Transcripción de documentos

English for Europe Quick Reference Guide ■ Accessories The following accessories are supplied with this product. PUSH Remote control Batteries (2) (AAA, R03, UM-4) AM loop antenna Indoor FM antenna VIDEO AUX input cover YPAO microphone Preparing the remote control 1 3 2 1 Take off the battery compartment cover. 2 Insert the two supplied AAA batteries into the battery case, following the polarity markings. 3 Snap the battery compartment cover back into place. ■ Items necessary for connection Speakers Ex. Ex. Front speaker Ex. Center speaker Surround speaker Ex. Active subwoofer • Use speakers with an impedance of at least 6Ω. • If you are using a CRT TV, we recommend that you use magnetically shielded speakers. • Prepare at least two speakers (for front). The priority of the other speakers is as follows: 1 Two surround speakers 2 One center speaker Cable External components • Cables for connecting external components (may differ depending on the devices you are connecting) • Speaker cables (a quantity to match the number of speakers you are connecting) • Audio pin cable (for subwoofer) TV Playback device such as BD (Blu-ray Disc)/DVD players -1-  Connect and install as follows the first time you use this unit. See the following explanations for the connections for each number. TV 3 2 BD/DVD player (recorder) 4 This unit Front speaker R Front speaker L Subwoofer 1 Surround speaker R Center speaker 1 Surround speaker L 1 Connect the speakers 2 Connect a TV 3 Connect playback device such as BD/DVD players and recorders 4 Connect the AC power cord, and turn the power on When connection and installation is finished, set up the speaker parameters automatically 5 . -2-  1 Connect the speakers Surround speaker R L Front speaker R L Caution: • Remove the AC power cord of this unit from the power outlet before connecting the speakers. • Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the “+” (positive, red) terminal on this unit and the speakers, and the other cable into the “-” (minus, black) terminal. • Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES!” will appear on the front panel display when this unit is switched on. ANTENNA FM GND AM SPEAKERS FRONT SURROUND CENTER SUBWOOFER Subwoofer Center speaker Connecting center speakers / surround speakers Connecting front speakers KE RS 2 SU RR OU 3 FR ON EA KE CE NT ER T 1 3 1 2 4 1 SP ND Remove approximately 10mm of insulation from the ends of the speaker cables, and twist the bare wires of the cables together firmly so that they will not cause short circuits. 1 Press the tab on the speaker terminal down. 2 Insert the speaker cable end into the terminal. Lift the tab to fix the speaker cable in place. 2 Loosen the speaker terminals. 3 3 Insert the bare wire of the speaker cable into the gap on the side of the terminal. Connecting the subwoofer 4 Tighten the terminal. 1 Connect the subwoofer input jack to the SUBWOOFER jack on this unit with an audio pin cable. 2 Set the subwoofer volume as follows. Volume: Set to approximately half volume (or slightly less than half). Crossover frequency (if available): Set to maximum. VOLUME MIN MAX CROSSOVER/ HIGH CUT MIN MAX Subwoofer examples -3-  2 Connect a TV Video input to this unit is output to a TV using output jacks of the same kind. When you have made connections using different types of video such as HDMI and component video, make the same connection with your TV. When viewing, be sure to switch the input source on your TV to match the playback device. Input Output HDMI HDMI COMPONENT VIDEO COMPONENT VIDEO VIDEO VIDEO HDMI input Component video input Video input If your TV has multiple inputs, connect with the following priority (A to C). HDMI HDMI COMPONENT VIDEO PR HDMI PB ARC (BD/DVD) HDMI OUT DOCK HDMI 2 HDMI 1 HDMI 3 HDMI 4 VIDEO COMPONENT PVIDEO R PR V PR PR PB PB PB PB COMPONENT VIDEO PR B When using a component V Y Y A When using an HDMI compatible TV. Y PB V Y COMPONENT VIDEO Y MONITOR OUT MONITOR OUT V VIDEO Y VIDEO video input-compatible TV. V OPTICAL A 1 AV COAXIAL AV A 2 COAXIAL OPTICAL (CD) ( TV ) AV A 3 AV A 4 A AV OUT AV A 5 AUDIO 1 AUDIO 2 AUDI OUT VIDEO V C When using a TV compatible with video input only. Listening to TV audio To playback TV audio on this unit, connect the TV audio output to this unit. When using an HDMI compatible TV that supports Audio Return Channel functions and / or HDMI Control functions (Ex. Panasonic VIERA Link), you can enjoy the TV sound on this unit as follows: Connect the following input jacks, matching the audio output jacks on your TV. When viewing your TV, select the appropriate input source on this unit. When using a TV that supports the Audio Return Channel functions and HDMI Control functions The audio / video output from the unit to the TV and audio output from the TV to the unit are possible using a single HDMI cable. The input source is switched automatically to match operations carried out on the TV, and that makes TV sound control easier to use. For the connections and settings, refer to “Single HDMI cable input to TV audio with Audio Return Channel function” in Owner’s Manual. ARC ARC OPTICAL O DOCK (BD/DVD) HDMI OUT HDMI 2 HDMI 1 H COMPONENT VIDEO Audio output PR PR PB PB Y MONITOR OUT Y COMPONENT VIDEO VIDEO O OPTICAL AV 1 COAXIAL AV 2 COAXIAL OPTICAL (CD) ( TV ) AV 3 AV 4 AV 5 When using a TV that supports HDMI Control functions Audio output from TV Input jack on this unit Optical digital output AV1 or AV4 Coaxial digital output AV2 or AV3 Analog output AV5, AUDIO1, AUDIO2, or V-AUX HDMI Audio Return Channel (Described in the right column) HDMI OUT When HDMI Control functions are enabled on the unit, input source can be switched automatically to match operations carried out on the TV. For the connections and settings, refer to “Switching the input source on this unit automatically when listening to TV audio” in Owner’s Manual. ✽ Connecting to AV4 allows you to playback TV audio just by pressing the “TV” under “SCENE” key. -4-  3 Connect playback device such as BD/DVD players and recorders If your playback device has multiple audio/video outputs, connect with the following priority (A to D) to enjoy a higher quality sounds and images. A When playback device is HDMI HDMI capable of HDMI output B When playback device is capable of component video output (with optical digital audio output) COMPONENT VIDEO PR HDMI PB ARC Y O (BD/DVD) HDMI OUT DOCK COMPONENT VIDEO OPTICAL PB capable of component video output (with coaxial digital audio output) HDMI 4 PB PB Y COMPONENT VIDEO HDMI 3 PR PR PB C When playback device is HDMI 2 HDMI 1 PR PR Y Y COMPONENT VIDEO Y MONITOR OUT PR V MONITOR OUT VIDEO L PB O Y R OPTICAL COAXIAL AV 1 COAXIAL AV 2 COAXIAL OPTICAL (CD) ( TV ) AV 3 A AV 4 A AV 5 A AV OUT AUDIO 1 AUDIO 2 AUDIO OUT C C D When playback device is capable of video output (with analog audio output) only • • • • VIDEO V AUDIO L R When playback, select the corresponding input source the jack is connected. Connecting to HDMI1 allows you to select the HDMI input just by pressing the “BD/DVD” under “SCENE” key. Connecting to AV3 allows you to select the AV3 input just by pressing the “CD” under “SCENE” key. If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from component video output jacks and audio from analog output jacks. Refer to Owner’s Manual for details. 4 Connect the AC power cord, and turn the power on Be sure to aim the remote control directly at the remote control sensor on this unit during operation. AC power cord To the power outlet. 30 30 within 6m TRANSMIT RECEIVER SLEEP HDMI 1 2 1 2 3 4 3 4 AV AUDIO 5 V-AUX -5- 1 2 DOCK Press  5 Set up the speaker parameters automatically (YPAO) When connection is finished, adjust the status, sizes, and volume balance of the speakers to provide an optimal sound field. This unit is equipped with a YPAO (Yamaha Parametric room Acoustic Optimizer) function that adjusts the speaker balance automatically with a simple procedure. When you use YPAO, a test tone will be output from the speakers for approximately three minutes and acoustic measuring will be performed. When using YPAO, be careful of the following. • The test tone is output at high volume. Please refrain from using this function at night when it may be a nuisance to others nearby. • Please take care that the test tone does not frighten any small children. 1 Check the following before using YPAO. This unit • The headphones are removed. Subwoofer • The power is turned on. • The auto power-off function (if present) is set to off. • Volume is set to approximately half, and the cross-over frequency (if present) is set to maximum. CROSSOVER/ HIGH CUT VOLUME MIN MIN MAX MAX Subwoofer examples 2 Place the supplied YPAO microphone at ear height in your listening position. YPAO microphone When positioning the microphone, we recommend that you use equipment that allows you to adjust the height (such as a tripod) as a microphone stand. When using a tripod, use the tripod screws to fix the microphone in place. 3 Press RECEIVER A on the remote control to switch this unit on. Continues to the next page -6-  4 Connect the YPAO microphone to the YPAO MIC jack on the front panel. RECEIVER A YPAO microphone DOCK “MIC ON. YPAO START” appears on the front panel display, and then changes to display the following. YPAO VOL. Press [SETUP] L SL SW C R SR SETUP This completes preparations. To achieve more accurate results, be careful of the following when measuring. • Measuring will take approximately three minutes. Keep the room as quiet as possible during measurement. • Wait in the corner of the listening room during measurement or leave it entirely, to avoid becoming an obstruction between the speakers and the YPAO microphone. 5 Press SETUP on the remote control to start measurement. Progress YPAO Progress VOL. 00% SW C L SL R SR The following display appears if measurement finishes without any problems. YPAO VOL. YPAO Complete L SL SW C R SR Note When a problem occurs, an error message or a warning message appears either during or after measurement. Refer to “Set up the speaker parameters automatically (YPAO)” in Owner’s Manual to solve the problem, and carry out YPAO again. 6 Press ENTER on the remote control to apply the results of measurement. YPAO VOL. Disconnect MIC 7 L SL SW C R SR Remove the YPAO microphone. YPAO finishes automatically when the YPAO microphone is removed. -7- ENTER  Operation guide A Switches this unit between on and standby modes This unit switches between on and standby mode every time you press this key. TRANSMIT B Choose an input source to listen to RECEIVER The name of the selected input source appears on the front panel display. SLEEP HDMI VOL. HDMI1 L SL SW C 1 2 R SR 3 4 3 4 AV 1 2 AUDIO C Select sound field programs and sound decoders 5 1 V-AUX Front panel Remote control Description MUSIC PROGRAM ENHANCER STEREO DOCK TUNER Selects sound field programs optimized for viewing movies, dramas, and sports. Selects sound field programs optimized for appreciating music. Selects settings for stereo playback or enhancers for compressed audio. MOVIE 2 FM AM INFO MEMORY MOVIE MUSIC PRESET TUNING ENHANCER SUR. DECODE STEREO STRAIGHT SCENE SUR. DECODE Selects surround decoders such as Dolby Pro Logic II. BD DVD TV SETUP STRAIGHT CD RADIO OPTION Switches to straight decoding mode for faithful reproduction of audio / video. STRAIGHT ENTER VOLUME RETURN D Adjusts the volume level The current volume level is displayed on the front panel display. MUTE VOL. Volume -18.5dB L SL SW C R SR E Mutes the sound The indicator blinks while the sound is muted. F Switches between input settings You can switch input sources and sound field programs with a single key. SCENE Input Sound field program BD/DVD TV CD RADIO HDMI 1 AV4 AV3 TUNER STRAIGHT STRAIGHT STRAIGHT 5ch Enhancer - Pressing and holding this key allows you to store input sources/sound field programs. - Press this key when this unit is in standby mode to switch on the unit. G Adjusting high/low-frequency sound (Tone control) 1 Press TONE CONTROL to select “Treble” or “Bass.” TONE Treble 2 VOL. 0.0dB L SL SW C R SR Press PROGRAM l / h to increase the setting. - You can set the tone control for speakers and headphones separately. Connect the headphones when adjusting the headphone tone control. - If you set an extreme tone balance, sounds may not match those from other channels. © 2011 Yamaha Corporation -8- YD282A0/QREN2