Transcripción de documentos

RX-V901 Natural Sound Stereo Receiver Thank you for selecting this YAMAHA stereo receiver. OWNER’S MANUAL CAUTION RISK OF ELECTRIC SHOCK CONTENTS Safety Instructions ................... 2 Features ................................... 4 Supplied Accessories .............. 4 Profile of This Unit .................... 5 Speaker Setup for This Unit.................................... 6 Connections ............................. 7 Speaker Balance Adjustment ... 12 Basic Operations .................... 15 Tuning Operations .................. 18 Preset Tuning ...........................19 Using Digital Sound Field Processor (DSP) .................... 22 Setting the SLEEP Timer ....... 26 Remote Control Transmitter ... 27 Troubleshooting ...................... 33 Specifications ......................... 34 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT! Please record the serial number of this unit in the space below. • Explanation of Graphical Symbols Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.  SAFETY INSTRUCTIONS 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. A. The power-supply cord or the plug has been damaged; Retain Instructions – The safety and operating instructions should be retained for future reference. B. Objects have fallen, or liquid has been spilled into the unit; 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. C. The unit has been exposed to rain; or 4 Follow Instructions – All operating and other instructions should be followed. 5 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 2 6 or or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. 19 Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST 10 Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. GROUND CLAMP 11 Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS 12 Cleaning – The unit should be cleaned only as POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) recommended by the manufacturer. 13 Nonuse Periods – The power cord of the unit should be ANTENNA LEAD IN WIRE NEC – NATIONAL ELECTRICAL CODE unplugged from the outlet when left unused for a long period of time. Note to CATV system installer: 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: 2 This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.  Caution: Read this before operating your unit 1 2 3 4 5 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. Do not operate the unit upside-down. It may overheat, possibly causing damage. Never open the cabinet. If something drops into the set, contact your dealer. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 6 7 8 9 10 Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Always set the VOLUME control to “– ∞” before starting the audio source play. Increase the volume gradually to an appropriate level after the play back has been started. To prevent lightning damage, pull out the power cord and remove the antenna cable during an electrical storm. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. AC outlet Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide. FCC INFORMATION 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. 3  FEATURES ● 5 Speaker Configuration ● Test Tone Generator for Easier Speaker Output Balance Adjustment ● 3 Center Channel Modes (NORMAL/WIDE/PHANTOM) ● 40-Station Random Access Preset Tuning ● Automatic Preset Tuning Digital Sound Field Processor 6 Programs for Digital Sound Field Processing 2 Programs for Dolby Surround Decoding (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED) ● Preset Station Shifting Capability (Preset Editing) ● IF Count Direct PLL Synthesizer Tuning System ● Video Signal Input/Output Capability Automatic Input Balance Control for Dolby Surround ● SLEEP Timer ● Remote Control Capability Front: 85W + 85W (8Ω) RMS Output Power, 0.07% THD, 1 kHz Center: 85W (8Ω) RMS Output Power, 0.07% THD, 1 kHz Rear: 20W + 20W (8Ω) RMS Output Power, 0.3% THD, 1 kHz ● ● SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. Remote Control Transmitter <U.S.A., Canada and Australia models> 4 Batteries (size AA, R6, UM-3) Indoor FM Antenna User Program Sheets AM Loop Antenna <General model>  PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on. In addition, you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder. Please read this operation manual carefully and store it in a safe place for later reference. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert. What’s more, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home. Dolby Pro Logic Surround The Dolby Pro Logic Surround Decoder program lets you experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic gets its name from its professional-grade steering logic circuitry, which provides greater effective front and rear channel separation for a much higher degree of realism than the “passive” Dolby Surround circuits found in less sophisticated home audio/video equipment. Dolby Pro Logic Surround provides a true center channel, so that there are four independent channels, unlike passive Dolby Surround which has in effect only three channels: left, right, and rear. This center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from action on the screen while getting a stereo effect as well. This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system increases sound stability at each channel and minimizes crosstalk between channels compared to conventional analog Dolby signal processing. In addition, this unit features a built-in automatic input balance control. This circuit always presents you the best surround conditions without performing manual adjustments. Dolby Pro Logic Surround + DSP You can also enjoy a combination of Dolby Pro Logic Surround and DSP in the sound field program “ PRO LOGIC ENHANCED”. It recreates the surround effect of a movie theater, effectively duplicating its multiple surround loudspeaker system, completely surrounding the listener with the sounds of the action taking place on the screen. 5  SPEAKER SETUP FOR THIS UNIT SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The speakers to be used with this unit will be mainly front speakers, rear speakers, and a center speaker. (You can omit the center speaker. Refer to the “4-Speaker Configuration” shown below.) The front speakers are used for the main source sound and the effect sound. They will probably be the speakers of your present stereo speaker system. The rear speakers are used for the effect sound. And the center speaker is used for the center sound (dialog etc.) encoded with the Dolby Surround. The rear and center speakers do not need to be equal in power to the front speakers. However, all the speakers should have high enough power handling to accept the maximum output of this unit. SPEAKER CONFIGURATION 5-Speaker Configuration 4-Speaker Configuration This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as well as the rear speakers. If the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, conversations will be output from the center speaker and the ambience will be excellent. ● Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 13.) The center speaker is not used in this configuration. If the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound is output from the left and the right front speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration. ● Be sure to set the center channel mode to the “PHANTOM” position. (For details, refer to page 13.) Front L Center Front R Front L Dialogue Dialogue Surround sound Surround sound Rear L Rear R Rear L Front R Rear R SPEAKER PLACEMENT The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following. Front: In normal position. (The position of your present stereo speaker system.) Rear: Behind your listening position, facing slightly inward. Nearly six feet (approx. 1.8 m) up from the floor. Center: Precisely between the front speakers. (To avoid interference with TV sets, use a magnetically shielded speaker.) Front R Center Front L TV set Rear R Rear L 6  CONNECTIONS Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. LD player, TV tuner, etc. AUDIO IN VIDEO OUT AUDIO OUT VIDEO IN Video cassette recorder 2 VIDEO OUT VIDEO IN AUDIO OUT Monitor TV GND OUTPUT Turntable (U.S.A. model) OUTPUT 8ΩMIN. /SPEAKER FRONT CENTER REAR REAR GND 75Ω UNBAL. AC OUTLETS CENTER FM ANT C SWITCHED I20W MAX. TOTAL l20W MAX. TOTAL I.0A MAX. TOTAL D DUAL C D:4ΩMIN./SPEAKER SINGLE:8ΩMIN./SPEAKER VIDEO SIGNAL GND MONITOR LD/TV OUT IN VCR 1 OUT IN VCR 2 OUT LOW PASS fc:200Hz SINGLE MAINS SPEAKERS SPEAKERS AM ANT A A A OR B:8ΩMIN. /SPEAKER A B:l6ΩMIN. /SPEAKER B PHONO CD TAPE REC PB OUT TAPE IN LD/TV OUT VCR 1 IN B OUT VCR 2 FRONT AUDIO SIGNAL CD player Tape deck VIDEO IN AUDIO IN AUDIO OUT VIDEO OUT LINE IN OUTPUT LINE OUT To AC outlet Video cassette recorder 1 : Refer to “ABOUT THE ACCESSORY TERMINALS” on page 10. CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL) These terminals are used to connect any video input source such as a camcorder to this unit. VIDEO AUX VIDEO L AUDIO R AUDIO OUT R AUDIO OUT L VIDEO OUT R L VIDEO Camcorder 7  CONNECTING SPEAKERS Connect the respective speakers to this unit as figured below. Rear speakers Left Right OUTPUT 8ΩMIN. /SPEAKER FRONT CENTER REAR REAR CENTER C D DUAL C D:4ΩMIN./SPEAKER SINGLE:8ΩMIN./SPEAKER Center speaker LOW PASS fc:200Hz SINGLE SPEAKERS SPEAKERS A A B B FRONT Left Right Left Right Front speakers A Front speakers B Note on front speaker connection: One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. IMPEDANCE SELECTOR switch (Canada model only) Be sure to switch this only when the power of this unit is turned off. Select the position proper for the use of your front speakers. Note on center speaker connection: One or two center speakers can be connected to this unit. If you cannot place the center speaker on or under the TV, it is recommended to use two center speakers and place them on both sides of the TV to orient the center sound at the center position. For connecting two center speakers, follow the method shown below. When using one pair of front speakers; • If the impedance of each speaker is 8Ω or higher, set to right ( ). • If the impedance of each speaker is 4Ω or higher, but lower than 8Ω, set to left ( ). A OR B:USE 4ΩMIN. /SPEAKER A B:USE 8ΩMIN. /SPEAKER A OR B:USE 8ΩMIN. /SPEAKER When using two pairs of front speakers; The impedance of each speaker must be 8Ω or higher. Set this switch to left ( ). IMPEDANCE SELECTOR SELECTEUR D’IMPEDANCE REAR CENTER C D DUAL FRONT LEVEL switch (Australia model only) Normally set to “0 dB”. If desired, you can decrease the output level at the FRONT SPEAKERS terminals by 10 dB by setting this switch to “–10 dB”. l0 dB 0 dB FRONT LEVEL l SINGLE Center speaker 8 Center speaker  How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers. Note Use speakers with the specified impedance shown on the rear of this unit. For connecting to the FRONT SPEAKERS terminals Red: positive (+) Black: negative (–) For connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) ➀ Unscrew the knob. ➁ Insert the bare wire. 2 1 [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire. 3 <U.S.A., Canada and General models only> ➀ Press up the tab. ➁ Insert the bare wire. ➀ ➂ [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Release the tab and secure the wire. ➁ Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. 9  ABOUT THE ACCESSORY TERMINALS AC OUTLET(S) (SWITCHED) FRONT OUTPUT terminals (U.S.A., Canada and General models) ...........................................................2 SWITCHED OUTLETS (Australia model) ................................. 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 120 watts. These terminals are for front channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive front speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. This terminal is for output to a monaural amplifier driving a subwoofer. Only frequencies below 200 Hz from the front and center channels are output. ADDING A SUBWOOFER You may wish to add a subwoofer to reinforce the bass frequencies. Connect the LOW PASS terminal to the INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. OUTPUT CENTER REAR LOW PASS fc:200Hz Subwoofer system 10 These terminals are for rear channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive rear speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. CENTER OUTPUT terminal LOW PASS terminal FRONT REAR OUTPUT terminals This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal.  ANTENNA CONNECTIONS ● ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Outdoor AM antenna Indoor FM antenna (included) AM loop antenna (included) GND 75Ω UNBAL. FM ANT 300-ohm feeder GND AM ANT TAPE PB PHONO 75-ohm coaxial cable CD 75-ohm/300-ohm antenna adapter Ground Connecting the AM loop antenna 1 2 ➀ ➂ ➁ 3 Orient so that the best reception is obtained. * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes ● When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. ● If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. 11  SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor. The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. Otherwise, the result may not be satisfactory. <For U.S.A., Canada and Australia models only> Use the remote control transmitter with the YPC-USER-LEARN switch on it set to the YPC position. 1 5 4 <U.S.A., Canada and Australia models> SEARCH STOP PLAY DIR A DIR B <General model> TAPE MON REC PAUSE REC MUTE REC/PAUSE DIR A PLAY TEST SEARCH PAUSE/STOP PLAY LD/TV 5 PRO LOGIC 1 ENHANCED DISPLAY STOP CONCERT VIDEO MONO MOVIE 3 4 DISCO ROCK HALL 6 7 2 VCR 1 VCR 2 SURROUND STADIUM 5 V–AUX HALL DELAY TIME 1 ON/OFF 5 Set to the “ ∞ ” position. PRO LOGIC ENHANCED A B ON ON DISCO OFF OFF * If you use two front speaker systems, press both the A and B switches. 3 BASS TREBLE l l 2 3 3 4 4 5 5 0 BALANCE l 2 l 2 3 3 4 4 5 5 Set to the “0” position. 12 V AUX VOLUME Select the PRO LOGIC or PRO LOGIC ENHANCED mode, so that the corresponding name is illuminated on the display. DIGITAL SOUND FIELD PROCESSOR SPEAKERS 2 EFFECT ON/OFF POWER Select the front speakers to be used. 0 VCR 2 MASTER VOLUME 4 l DISCO 3 2 2 ROCK REAR LEVEL VCR 1 SUR. MONO MOVIE STADIUM 8 EFFECT DSP CENTER LEVEL TAPE MON LD/TV ENHANCED CNCT VIDEO PRO LOGIC CHAPTER/CH DIR B STOP 0 l 2 2 3 3 4 4 L 5 5 R CONCERT VIDEO ROCK CONCERT CONCERT HALL MONO MOVIE STADIUM EFFECT 5  <U.S.A., Canada and Australia models> 8 6 <General model> SURROUND STADIUM DISCO ROCK HALL 5 6 7 8 EFFECT DSP ON/OFF CENTER LEVEL V–AUX REC PAUSE 7 MASTER VOLUME DELAY TIME REAR LEVEL RESET CLEAR CENTER LEVEL DIR B TAPE MON LD/TV ENHANCED CNCT VIDEO VCR 1 SUR. MONO MOVIE STADIUM ROCK REAR LEVEL PLAY STOP PRO LOGIC 8 7 TEST DIR A TEST HALL DISCO VCR 2 EFFECT ON/OFF V AUX DELAY TIME VOLUME 8 6 Select the center channel output mode according to your speaker configuration. (Refer to “SPEAKER CONFIGURATION” on page 6.) CENTER MODE 7 TEST TEST ER Flashes continuously. NORMAL WIDE PHANTOM 8 Turn up the volume. MASTER VOLUME <U.S.A., Canada and Australia models> <General model> VOLUME On the feature of each mode, refer to the “Note” shown below. Note In step 6, when you select the center channel output mode, note the following. For 5 speaker configuration) NORMAL: Select this mode when you use a center speaker that is smaller than the front speakers. In this mode, the bass tone will be output from the front speakers. WIDE: Select this mode when you use the center speaker approximately same sized as the front speakers. You will hear a test tone (like pink noise) from the left front speaker, then the center speaker, then the right front speaker, and then the rear speakers, for about two seconds each. The display changes as shown below. Front (L) Center TEST For 4 speaker configuration) PHANTOM: Select this mode when you do not use the center speaker. The center sound will be output from the left and right front speakers. Rear (L and R) Front (R) * The test tone from the left rear speaker and the right rear speaker will be heard at the same time. CONTINUED 13  <U.S.A.,Canada and Australia models> PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE 1 2 3 4 <General model> VCR 2 SURROUND STADIUM DISCO ROCK 5 6 7 HALL DSP 10 1 12 9 9 Adjust the BALANCE control so that the effect sound output level of the left front speaker and the right front speaker are the same. CENTER LEVEL 0 2 RESET 11 3 10 DIR A PLAY TEST STOP CENTER LEVEL MONO MOVIE STADIUM PRO LOGIC DIR B TAPE MON LD/TV ENHANCED CNCT VIDEO VCR 1 SUR. ROCK REAR LEVEL HALL DELAY TIME DISCO VCR 2 EFFECT ON/OFF V AUX VOLUME CLEAR Adjust the sound output level of the rear speakers to be at the same level as that of the front speakers with the REAR LEVEL keys. 4 L 5 12 10 11 <U.S.A., Canada and Australia models> 2 4 TEST DELAY TIME l 3 MASTER VOLUME REAR LEVEL BALANCE l ON/OFF REC PAUSE V–AUX 8 EFFECT <General model> REAR LEVEL 5 R REAR LEVEL Adjust the sound output level of the center speaker to be at the same level as that of the front speakers with the CENTER LEVEL keys. TEST <U.S.A., Canada and Australia models> <General model> Lights up. 0 REAR Adjustable CENTER LEVEL CENTER LEVEL 12 Cancel the test tone. TEST TEST R TEST Stops flashing and disappears Lights up. CENTER 00 Notes Once you have completed these adjustments, you can adjust whole sound level on your audio system by using the VOLUME control (or the VOLUME keys on the remote control transmitter). ● If you use external power amplifiers, their volume controls may also be adjusted to achieve proper balance. ● In step 10, if the center channel mode is in the “PHANTOM” position, the sound output level of the center speaker cannot be adjusted. This is because in this mode, the center sound is automatically output from the left and right front speakers. ● <Australia model only> If there is insufficient sound output from the center and rear speakers, you may decrease the front speaker output level by setting the FRONT LEVEL switch on the rear panel to “–10 dB”. ● Adjustable 14  BASIC OPERATIONS 1, 6 3 2 4 7 7 TO PLAY A SOURCE 1 5 Play the source. (For detailed information on the tuning operation, refer to page 18.) 6 Set to the “ ∞ ” position. 2 POWER Adjust to the desired output level. 7 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON.) TAPE MONITOR TUNER CD PHONO VIDEO AUX VCR 2 VCR 1 LD/TV * The name of the selected input source will appear in the display. 4 Select the front speakers to be used. SPEAKERS A B ON ON OFF OFF If desired, adjust the BASS, TREBLE, BALANCE controls, etc. (refer to page 17) and use the digital sound field processor. (Refer to page 24.) Notes on using the input selector buttons Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. * To select the source connected to the VIDEO AUX terminals on the front panel, press VIDEO AUX. ● The selection of TAPE MONITOR cannot be canceled by pressing another input selector button. To cancel it, press TAPE MONITOR again. When you select a button other than TAPE MONITOR, make sure that TAPE MONITOR is not also selected. ● If you select the input selector button for a video source without canceling the selection of TAPE MONITOR, the playback result will be the video image from the video source and the sound from the audio tape. ● Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. ● To turn off the power Press the POWER switch again. * If you use two front speaker systems, press both the A and B switches. 15  1, 4 2 TO RECORD A SOURCE TO TAPE (OR DUB FROM TAPE TO TAPE) 1 2 3 4 16 Note DSP, VOLUME, BASS, TREBLE and BALANCE control settings have no effect on the material being recorded. Select the source to be recorded. TAPE MONITOR TUNER CD PHONO VIDEO AUX VCR 2 VCR 1 LD/TV Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to page 18.) Set the tape deck or VCR to the recording mode. If the tape deck is used for recording, you can monitor the sounds being recorded by pressing TAPE MONITOR. TAPE MONITOR TUNER CD PHONO VIDEO AUX VCR 2 VCR 1 LD/TV  Selecting the SPEAKER system Because one or two speaker systems (as front speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. Adjusting the BASS and TREBLE controls BASS l 0 TREBLE l 2 SPEAKERS A B ON ON OFF OFF 3 l 2 3 4 5 0 2 3 4 BASS l 2 3 4 5 4 5 5 : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE l 0 l 2 2 3 TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Note These controls are effective only for the sound from the front speakers. 3 4 4 L 5 5 R Note This control is effective only for the sound from the front speakers. When you listen with headphones Connect the headphones to the PHONES jack. You can listen to the sound to be output from the front speakers through headphones. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position and switch off the digital sound field processor (so that no DSP program name is illuminated on the display) by pressing the EFFECT switch. PHONES 17  TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). 2 1 3 AUTOMATIC TUNING 1 MANUAL TUNING Select the reception band (FM or AM) while watching the display. 1 FM/AM FM/AM or FM 2 Select the reception band (FM or AM) while watching the display. AM FM 2 TUNING MODE 3 “AUTO TUNING” goes off. AUTO/MAN’L MONO DOWN TUNING 3 UP Tune to a desired station manually. DOWN To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. AM TUNING MODE AUTO TUNING AUTO/MAN’L MONO or TUNING UP * To continue tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. Display information ➀ ➀ ➁ ➁ ➂ STEREO PRESET FM MHz 0 20 ➂ 18 l00 RE Displays the band and frequency of the received station. Lights up when an FM stereo broadcast is received in stereo. Indicates the signal level of the received station.  PRESET TUNING MANUAL PRESET TUNING This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this function, you can select any desired station by only pressing the corresponding preset station button. Up to 40 stations (8 stations x 5 pages) can be stored. 2, 1 4, 2 (Preset station buttons) 3 To recall a preset station To store stations 1 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) Select the page of preset station buttons. A/B/C/D/E 2 PRESET Select a desired page (A – E) of preset station buttons while watching the display. A/B/C/D/E PRESET 2 Select the desired preset station button. l 2 3 PRESET STATIONS 4 5 6 7 8 3 MEMORY MEMORY MAN’L/AUTO FM PRESET Flashes on and off for about 5 seconds. 4 Press a preset station button before “MEMORY” goes off from the display. l 2 3 PRESET STATIONS 4 5 Notes A new setting can be programmed in place of the former one. ● For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. ● 6 7 8 STEREO PRESET FM MHz 0 20 l00 RE AUTO TUNING Shows the displayed station has been programmed to A1. * * Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. In the same way, program other stations to A2, A3 ... A8. You can program more stations to the preset station buttons on other pages in the same way by selecting other pages in step 2. 19  AUTOMATIC PRESET TUNING You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 19. 2 13 To store stations 1 When the automatic preset tuning is finished FM/AM FM The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 19. To recall a preset station 2 Simply follow the procedure of the section “To recall a preset station” on page 19. MEMORY PRESET MAN’L/AUTO FM MEMORY AUTO TUNING Press and hold for about 3 seconds. 3 DOWN Flashes. TUNING UP To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also programmed to the preset station numbers on other pages (B, C, D and E) in that order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the first received station to C5, select “C5” by using the A/B/C/D/E button and the preset station buttons after pressing the MEMORY button in step 2. Then press the TUNING button. The first received station is stored to C5, and next stations to C6, C7 ... sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically. 20 Notes ● You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 19. ● If the number of received stations is not enough to be stored up to E8, the search is finished automatically when it reaches the highest frequency after searching through all frequencies. ● With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 19.  EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. 2, 4 Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 2 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 19). 4 EDIT EDIT MEMORY Flashes 3 Next, recall the preset station on A5 by following the same method with step 1. Shows the exchange of stations is completed. MEMORY Flashes 21  USING DIGITAL SOUND FIELD PROCESSOR (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand and shape the audio sound field from both the audio and video sources, for a theater-like experience in the listening/viewing room. This digital sound field processor has 8 programs; 6 programs for digital sound field processing and 2 programs for the Dolby Pro Logic Surround sound system (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED). You can create an excellent audio sound field by selecting the suitable program and adding desired adjustments. In addition, when the DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED program is selected, the built-in automatic input balance control functions. This presents you the best surround condition without manual adjustment. Front Panel 1 CINEMA DSP AM FM ENTER MEMORY TAPE MONITOR AUTO TUNING NORMAL WIDEPHANTOM 0 20 CD PHONO VIDEO AUX VCR 2 VCR 1 LD/TV SLEEP kHz MHz TUNER TEST STEREO PRESET TAPE MONITOR l00 DELAY CENTER REAR ms PRO LOGIC CONCERT MONO STADIUM ROCK CONCERT ENHANCED VIDEO MOVIE DISCO CONCERT HALL DIGITAL SOUND FIELD PROCESSOR 2 DOWN PRESET STATIONS 4 5 3 TUNING UP CENTER MODE DELAY TIME 2 3 6 7 8 CENTER LEVEL PRO LOGIC ENHANCED REAR LEVEL 4 DISCO CONCERT VIDEO MONO MOVIE ROCK CONCERT CONCERT HALL STADIUM EFFECT 5 6 Remote Control Transmitter <U.S.A., Canada and Australia models> <General model> 1 Displays your selection on the DSP or other informations. 2 CENTER MODE Selects the center channel output mode. (For details, refer to page 13.) TRANSMIT USER LEARN /LEARN YPC POWER SLEEP TV VCR SKIP AUX 3 DELAY TIME –/+ PHONO DISC SKIP SEARCH PAUSE/STOP DECK A/B PRESET PLAY A/B/C/D/E TUNER STOP PLAY TAPE MON DIR A DIR B SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 SEARCH REC MUTE REC/PAUSE POWER SLEEP 7 DECK A/B PAUSE/STOP PRESET DIR A TEST 5 ENHANCED CONCERT VIDEO MONO MOVIE 1 2 3 4 STADIUM 5 DISCO ROCK 6 7 HALL 3 4 TEST DELAY TIME REAR LEVEL 4 DIR B TAPE MON LD/TV ENHANCED CNCT VIDEO 4 CENTER LEVEL –/+ 5 VCR 1 SUR. MONO MOVIE STADIUM ROCK REAR LEVEL MASTER VOLUME CD TUNER STOP PRO LOGIC CENTER LEVEL PLAY PLAY A/B/C/D/E HALL DELAY TIME DISCO VCR 2 EFFECT ON/OFF V AUX VOLUME 6 REAR LEVEL –/+ Adjusts sound output level at each speaker. (For details, refer to page 24 and 25.) 5 Selects a digital sound field program. 6 EFFECT Switches on/off the digital sound field processor (DSP). 7 7 TEST RESET 22 ON/OFF CENTER LEVEL V–AUX 8 EFFECT DSP 6 VCR 2 SURROUND PHONO DISC SKIP SKIP REC PAUSE PRO LOGIC Adjusts the delay time. (For details, refer to page 25.) CD CLEAR 3 Used for speaker balance adjustment. (For details, refer to page 12, 13 and 14.)  Description of Each Sound Field Program The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for them was recorded at the locations described using sophisticated sound field measurement equipment. Note The channel level balance between the left rear effect speaker and the right rear effect speaker may vary depending on the sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments. PROGRAM PRO LOGIC PRO LOGIC ENHANCED FEATURE This program is effective for playback of sources encoded with Dolby Surround. The employment of the digital signal processing system improves crosstalk and transfers the sound source more smoothly and precisely, compared to the conventional type. A stable movie sound field is recreated. This program is effective for playback of sources encoded with Dolby Surround. Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker systems of a 35 mm film theater, thus widening the surrounded-sound field with greater presence. CONCERT VIDEO This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall. MONO MOVIE This program is designed specifically to enhance mono source programs. Compared to a strictly mono setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective when used with old mono movies, news broadcasts and dialog. STADIUM DISCO This program gives you long delays between direct sounds and effect sounds, and extraordinarily spacious feel of a large stadium. This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. ROCK CONCERT This program is suitable for rock music. A big, powerful sound is reproduced lively and dynamically. CONCERT HALL In this program, the center seems deep behind the front speaker pair, creating an expansive, large hall ambience. Description of Dolby Pro Logic Surround DOLBY PRO LOGIC SURROUND: This unit employs the Dolby Pro Logic Surround system. This system is similar to professional Dolby Stereo decoders used in movie theaters. By employing a four-channel system, the Dolby Pro Logic Surround system divides the input signals into four levels: the left and right main channels, the center channel (to characterize dialog), and the rear surround-sound channels (to characterize sound effects, background noise and other ambient noise). Dolby Surround is encoded on the sound track of commercially available video cassettes and video discs as well. When you play a source encoded with Dolby Surround on your home video system, the Dolby Pro Logic Surround system in this unit decodes the signal and feeds the surround-sound effects. The Dolby Pro Logic Surround mode may not be always effective on video sources not encoded with Dolby Surround. Manufactured under license from Dolby Laboratories Licensing Corporation. Additionally licensed under Canadian patent number 1,037,877. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. 23  To play a source with the digital sound field processor <U.S.A., Canada and Australia models> CHAPTER/CH 2 DISPLAY STOP VCR 1 PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE VCR 2 1 2 3 4 DISCO ROCK HALL 6 7 <General model> REC PAUSE DIR A TEST 5 V–AUX PRO LOGIC ON/OFF LD/TV CENTER LEVEL REAR LEVEL CENTER LEVEL 3 ENHANCED CNCT VIDEO VCR 1 SUR. MONO MOVIE STADIUM DISCO VCR 2 EFFECT ON/OFF V AUX MASTER VOLUME ROCK TEST HALL DELAY TIME 2 VOLUME DELAY TIME REAR LEVEL RESET 2 TAPE MON 8 EFFECT 1 DIR B SURROUND STADIUM DSP 3 PLAY STOP CLEAR 2 3 Follow steps 1 – 6 shown in “BASIC OPERATIONS” on page 15. 3 If desired, adjust the delay time and the output level of each speaker. (For details, refer to the corresponding descriptions on this page and the next page.) Select the desired program that is suitable for the source. DIGITAL SOUND FIELD PROCESSOR CONCERT VIDEO PRO LOGIC ENHANCED DISCO ROCK CONCERT CONCERT HALL MONO MOVIE STADIUM EFFECT Notes ● If you prefer to cancel the DSP, press the EFFECT switch. The sound will be the normal 2-channel stereo without surround sound effect. ● When CONCERT VIDEO, MONO MOVIE, STADIUM, DISCO, ROCK CONCERT or CONCERT HALL is selected, no sound is heard from the center speaker. ● When a monaural sound source is played with DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is heard from the front speakers and the rear speakers. Sound is heard only from the center speaker. However, if the center channel mode is in PHANTOM, the front speakers output the sound of the center channel. ● When this unit’s Dolby Pro Logic Surround system is used, if the main-source sound is considerably altered by overadjustment of the BASS or TREBLE controls, the relationship between the center and rear channels may produce an unnatural effect. PRO LOGIC The selected program name is shown on the display. * The following adjustments can be done on the remote control transmitter as well as on the front panel. Adjustment of the CENTER LEVEL If desired, you can adjust the sound output level of the center speaker even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 14. By continuously pressing “+” or “–” on the CENTER LEVEL control, the level value changes continuously. However, the value stops changing momentarily at the preset point (80). ● If the digital sound field program CONCERT VIDEO, MONO MOVIE, STADIUM, DISCO, ROCK CONCERT or CONCERT HALL is selected, the CENTER LEVEL control cannot function. ● Once the output level is adjusted, the level value will be the same in the DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED programs. ● If a digital sound field program is not used, the CENTER LEVEL control will not function. Lights up. CENTER LEVEL CENTER Adjustable 24  Adjustment of the REAR LEVEL If desired, you can adjust the sound output level of the rear speakers even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 14. Lights up. By continuously pressing “+” or “–” on the REAR LEVEL control, the level value changes continuously. However, the value stops changing momentarily at the preset point (80). ● Once the output level is adjusted, the level value will be the same in all the digital sound field programs. ● If DOLBY PRO LOGIC or a digital sound field program is not used, the REAR LEVEL control will not function. REAR LEVEL REAR Adjustable Adjustment of DELAY TIME You can adjust the time difference between the beginning of the source sound and the beginning of the effect sound with the DELAY TIME control. The DELAY TIME control is effective with all programs. By applying more or less delay, sound effects, background noise, and ambient noise coming at you from the rear speakers can be enhanced or subdued for extra effect. 1. PRO LOGIC : from 15 to 30 milliseconds (Preset value: 20 milliseconds) 2. PRO LOGIC : from 15 to 30 milliseconds ENHANCED (Preset value: 20 milliseconds) 3. CONCERT VIDEO : from 1 to 100 milliseconds (Preset value: 28 milliseconds) 4. MONO MOVIE : from 1 to 100 milliseconds (Preset value: 20 milliseconds) 5. STADIUM : from 1 to 50 milliseconds (Preset value: 45 milliseconds) 6. DISCO : from 1 to 100 milliseconds (Preset value: 14 milliseconds) 7. ROCK CONCERT : from 1 to 100 milliseconds (Preset value: 17 milliseconds) 8. CONCERT HALL : from 1 to 100 milliseconds (Preset value: 30 milliseconds) By continuously pressing “+” or “–” on the DELAY TIME control, the value changes continuously. However, the value stops changing momentarily at the preset point. Adjustable DELAY TIME STEREO DELAY 0 20 l00 ms ONCERT VIDEO Note Adding too much delay will cause an unnatural effect with some sources. Experiment with the DELAY TIME control to create the effect that you find most suitable. Note The values of the DELAY TIME, CENTER LEVEL and REAR LEVEL you set the last time will remain memorized even when the power of this unit is off. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. 25  SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. Notes ● The SLEEP timer can be controlled only with the remote control transmitter. ● The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. To set the SLEEP time To cancel the selected SLEEP time 1 SLEEP SLEEP Press once or more to select the desired SLEEP time. Press once or more so that the display returns to the indication before the SLEEP timer is set. (“SLEEP” will go off from the display.) Indicates the SLEEP time. SLEEP ms l00 T Flashes on and off continuously. Whenever the SLEEP key is pressed, the SLEEP time will change as follows. (Minutes) 120 90 60 30 The SLEEP timer is OFF. (The indication before the SLEEP key is pressed.) After a while, the display returns to the indication before the SLEEP timer is set, and the “SLEEP” indicator stops flashing and lights up. 2 26 The unit will be turned off automatically at the selected SLEEP time. Note The SLEEP timer setting can also be canceled by turning off the power with the POWER switch or disconnecting the power plug of this unit from the AC outlet.  REMOTE CONTROL TRANSMITTER NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range <U.S.A., Canada and Australia models> Remote control sensor 2 1 3 Within approximately 6m (19.7 feet) 30° <General model> 30° 1 3 2 Notes ● There should be no large obstacles between the remote control transmitter and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control transmitter will not be used for an extended period of time. ● If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 27  KEY FUNCTIONS The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, tape deck, etc. connected to this unit are YAMAHA components, then this remote control transmitter will also control various functions of each component. <U.S.A., Canada and Australia models> 4 5 <General model> 6 45 6 TRANSMIT USER LEARN /LEARN YPC POWER SLEEP TV VCR SKIP AUX PHONO DISC SKIP 1 SEARCH PAUSE/STOP DECK A/B PRESET PLAY A/B/C/D/E POWER CD SEARCH REC MUTE REC/PAUSE SEARCH 3 STOP PLAY DIR A DIR B PAUSE/STOP PLAY 1 TUNER TAPE MON 2 7 REC PAUSE PAUSE/STOP PRESET DIR A TEST PLAY PLAY CD A/B/C/D/E TUNER DIR B TAPE MON STOP LD/TV 7 LD/TV PRO LOGIC CHAPTER/CH PHONO DISC SKIP DECK A/B 2 SLEEP SKIP DISPLAY STOP VCR 1 PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE VCR 2 1 2 3 4 CENTER LEVEL ENHANCED CNCT VIDEO VCR 1 SUR. MONO MOVIE STADIUM ROCK HALL DISCO VCR 2 EFFECT ON/OFF V AUX SURROUND STADIUM DISCO ROCK 5 6 7 HALL DSP ON/OFF CENTER LEVEL TEST DELAY TIME V–AUX REAR LEVEL 8 EFFECT MASTER VOLUME 8 REAR LEVEL RESET * 28 CLEAR When you operate this unit and/or other YAMAHA components with this remote control transmitter, set the YPC-USER-LEARN switch to the YPC (Yamaha Preset Code) position. DELAY TIME VOLUME 8  For Other Component Control For Control of This Unit Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their functions will be the same. On each key function, refer to the corresponding instruction on your component’s manual. 4 POWER Turns the power on/off. 5 SLEEP Refer to “SETTING THE SLEEP TIMER” on page 26. 1 CD player keys Controls compact disc player. * DISC SKIP is applicable only to compact disc changer. 6 Tuner keys Controls tuner. +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E Selects the page (A – E) of preset station buttons. 2 Tape deck keys Controls tape deck. * DIR A, B and DECK A/B are applicable only to double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. 3 LD player keys (U.S.A., Canada and Australia models only) Controls LD player. * Some models have a key which possesses both the functions of PLAY and PAUSE. 7 Input selector keys Selects input source. 8 (MASTER) VOLUME +/– Turns the volume level up/down. * For the DSP control keys, refer to the page 22. 29  REMOTE CONTROL “LEARNING” FUNCTION (U.S.A., Canada and Australia models only) All of the keys on this remote control transmitter can be programmed to “learn” key-functions from other remote control transmitters without losing the preset key functions. By using this feature, this unit can then be used in place of one or more other remote control transmitters, thus making operation of your various audio and video components more convenient. Use the included user program sheets to indicate a new function learned for each key. Note There may occasionally be instances in which, due to the signal-coding and modulation employed by the other remote control transmitter, this unit will not be able to “learn” its signals. ➊➋ ➊ TRANSMIT/LEARN indicator ➋ YPC-USER-LEARN TRANSMIT USER LEARN /LEARN YPC POWER SLEEP TV VCR SKIP AUX PHONO DISC SKIP SEARCH PAUSE/STOP DECK A/B PRESET SEARCH PLAY CD A/B/C/D/E TUNER TAPE MON STOP PLAY DIR A DIR B SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 VCR 2 REC MUTE REC/PAUSE switch Set to this position when using preset key functions (for controlling this unit and/or YAMAHA components). * “YPC” is the abbreviation of YAMAHA Preset Code. USER: Set to this position when using “learned” key functions. LEARN: Set to this position when learning new key functions from other remote control transmitters. YPC: PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE 1 2 3 4 ➌ ➌ Blank keys These keys have no preset functions and are used only for learning other remote control transmitter’s functions. SURROUND STADIUM DISCO ROCK 5 6 7 HALL DSP ON/OFF CENTER LEVEL TEST DELAY TIME REAR LEVEL RESET CLEAR V–AUX 8 EFFECT MASTER VOLUME ➍ RESET button Press this button to “reset” the internal microcomputer which controls remote control operations. Microcomputer “reset” is necessary when the remote control freezes. * Pressing the RESET button will not erase learned functions. ➎ CLEAR button This button is used to clear one or all learned key functions. (Refer to page 32.) ➍ ➎ 30  To Learn a New Function 1 YPC USER LEARN Set to the “LEARN” position. 2 Press a key on this unit where a new function will be learned. Notes ● When you operate the desired component with this remote control transmitter, TRANSMIT/LEARN indicator will flash steadily. ● The originally preset function of a key is still available in the USER position if a new function has not been learned to the key. ● Successful learning to a key results in the erasure of previously learned functions and their replacement by the newly learned ones. ● If there is no more room in the memory area for a function to be learned, the TRANSMIT/LEARN indicator will flash on and off. In this case, even if some keys are not occupied with functions from other remote control transmitters, no further learning is possible. This unit Other remote control transmitter Memory back-up All of the learned functions will be retained while you replace the batteries. However, if no batteries are installed for a few hours, the learned functions will be erased and will have to be learned again. About 5–10 cm (2–4 in.) 3 Press and hold the key (on the other remote control transmitter) where the desired new function is. Lights up. * When the TRANSMIT/LEARN indicator stops lighting, the learning is finished. 4 Repeat step 2 and 3 until all desired functions are successfully learned. 5 Set to the “USER” position. YPC USER LEARN Try operating your components. 31  To Clear a Learned Function 1 YPC USER To Clear All Learned Functions 1 YPC LEARN Set to the “USER” position. USER LEARN Set to the “LEARN” position. 2 Press and hold the CLEAR button using the point of a mechanical pencil, etc. 2 Press and hold the CLEAR button using the point of a mechanical pencil, etc. CLEAR CLEAR 3 Press and hold the key where the learned function to be deleted is until the indicator flashes 3 times. 3 Press and hold any key until the indicator flashes 7 times. TRANSMIT /LEARN TRANSMIT /LEARN To clear two or more functions, repeat step 2 and 3. Note If a key is not pressed soon after the CLEAR button is pressed, this unit will automatically return to the status that was in effect before the CLEAR button was pressed. Trouble shooting guide SYMPTOM The remote control transmitter does not work. Learning cannot be made successfully. (The TRANSMIT/LEARN indicator does not light up or flash.) CAUSE The batteries of this remote control transmitter are weak. The internal microcomputer “freezes”. The batteries of this remote control transmitter and/or the other remote control transmitter are weak. The distance between the two remote control transmitters is too long or too short. The signal coding or modulation of the other remote control transmitter is not compatible with this remote control transmitter. Memory capacity is full. The internal microcomputer “freezes”. 32 REMEDY Replace the batteries with new ones and press the RESET button on the remote control transmitter. Replacce the batteries (and press the RESET button for this remote control transmitter). Place the remote control transmitters with the proper distance. Learning is not possible. Further learning is not possible without deleting unnecessary commands. Press the RESET button on the remote control transmitter.  TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Firmly plug in the power cord. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input selector is not pressed. Press the appropriate input selector corresponding to the input source. The protection circuit has been activated because of short circuit etc. Turning the unit off and then on will reset the protection circuit. The SLEEP timer functioned. Do not make the SLEEP timer function. Incorrect setting of the BALANCE control. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The power to the component connected to the REC OUT terminals of this unit is off. Turn the power to the component on. No sound from the rear speakers. The sound output level to the rear speakers is set to 0. Turn up the sound output level with the REAR LEVEL control. The monaural sound source is played in DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED mode. Select another program suitable for the monaural sound source. The sound output level to the center speaker is set to 0. Turn up the sound output level with the CENTER LEVEL control. The center channel mode is in PHANTOM mode. Select NORMAL or WIDE. Only one side speaker outputs the sound. Sound “hums”. No sound from the center speaker. Incorrect sound field program selection. No sound field program is selected. FM REMEDY Power cord is not plugged in or is not completely inserted. The sound suddenly goes off. Amplifier CAUSE The unit fails to turn on when the POWER switch is pressed. Select the appropriate program. FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a multiple element FM antenna. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with Auto tuning. The station is too weak. Use Manual tuning mode. Use a high quality directional FM antenna. A desired station cannot be tuned in with Auto tuning. Weak signal or loose antenna connections. Tighten the AM loop antenna connections and rotate it for best reception. There are continuous crackling and hissing noises. Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit. Change the position of the main unit. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. The power to this unit is off. Turn the power to this unit on. Others Remote control transmitter AM Use Manual tuning mode. The sound is degraded when monitoring is performed by using the headphones connected to the compact disc player or cassette deck which are connected with this unit. 33  SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power per Channel Front L, R 8 ohms, 1 kHz, 0.07% THD [U.S.A. and Canada models] ...................................................85W+85W [Australia and General models] ...................................................70W+70W Center 8 ohms, 1 kHz, 0.07% THD [U.S.A. and Canada models] ............................................................75W [Australia and General models] ............................................................70W Rear L, R 8 ohms, 1 kHz, 0.3% THD............20W+20W Maximum Output Power [General model only] 8 ohms, 1 kHz, 10% THD (FRONT L/R) .................................................105W+105W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) [U.S.A. and Canada models] 8/6/4/2 ohms.................110/140/170/190W [Australia and General models] 8/6/4/2 ohms...................95/120/150/170W Dynamic Headroom [U.S.A. and Canada models only] 8 ohms............................................1.66 dB Power Band Width 8 ohms, 30W, 0.08% THD ..........................................10 Hz to 50 kHz Damping Factor (SPEAKERS A) 8 ohms, 20 Hz to 20 kHz .............80 or more Input Sensitivity/Impedance PHONO MM .....................2.5 mV/47 k-ohms CD/TAPE/LD·TV/VCR......150 mV/47 k-ohms Maximum Input Signal (1 kHz, 0.5% THD) PHONO MM......................................115 mV CD/TAPE/LD·TV/VCR (EFFECT ON) .....2.2V Output Level/Impedance REC OUT .......................150 mV/1.0 k-ohms PRE OUT ............................2.2V/1.2 k-ohms LPF (EFFECT OFF).............3.5V/1.5 k-ohms Headphone Jack Rated Output/Impedance Output Level (8 ohms, 1 kHz, 150 mV) ............................................................0.5V Impedance.....................................390 ohms Frequency Response (20 Hz to 20 kHz) CD/TAPE/LD·TV/VCR (FRONT L/R) ........................................................0±0.5 dB RIAA Equalization Deviation PHONO MM....................................0±0.5 dB 34 Total Harmonic Distortion PHONO MM to REC OUT 20 Hz to 20 kHz, 1V ..............0.02% or less CD/TAPE/LD·TV/VCR to SP OUT FRONT L/R (EFFECT OFF) 20 Hz to 20 kHz, 30W/8 ohms ...........................................0.02% or less REAR L/R 1 kHz, 10W/8 ohms ..............0.3% or less Signal-to-Noise Ratio (IHF-A Network) PHONO MM to REC OUT (5 mV Input Shorted) ...............................................85 dB or more CD/TAPE/LD·TV/VCR to SP OUT (Input Shorted, EFFECT OFF) .........99 dB or more Residual Noise (IHF-A Network) FRONT L/R ............................140 µV or less Channel Separation (Vol. –30 dB, EFFECT OFF) PHONO MM (Input Shorted 1 kHz/10 kHz) .....................60 dB or more/50 dB or more CD/TAPE/LD·TV/VCR (Input 5.1 k-ohms Shorted 1 kHz/10 kHz) .....................60 dB or more/44 dB or more Tone Control Characteristics BASS: Boost/cut ................±10 dB (50 Hz) Turnover Frequency .........(350 Hz) TREBLE: Boost/cut...........±10 dB (20 kHz) Turnover Frequency.....(3.5 kHz) Filter Characteristics LPF (fc=200 Hz)...............................6 dB/oct Gain Tracking Error (0 to –60 dB) ...................................................3 dB or less VIDEO SECTION Video Signal Level..................1 Vp-p/75 ohms Maximum Input Level............1.5 Vp-p or more Signal-to-Noise Ratio ................50 dB or more Monitor Out Frequency Response ..................................5 Hz to 10 MHz, –3 dB FM SECTION Tuning Range [U.S.A. and Canada models] .........................................87.5 to 107.9 MHz [Australia and General models] .........................................87.5 to 108.0 MHz 50 dB Quieting Sensitivity (IHF, 75 ohms) Mono ................................1.55 µV (15.1 dBf) Stereo .................................21 µV (37.7 dBf) Usable Sensitivity (75 ohms) (30 dB S/N Quieting, 1 kHz, 100% mod.) ..........................................0.8 µV (9.3 dBf) Image Response Ratio...........................45 dB IF Response Ratio..................................80 dB Spurious Response Ratio.......................70 dB AM Suppression Ratio............................55 dB Capture Ratio ........................................1.5 dB Alternate Channel Selectivity ................85 dB Signal-to-Noise Ratio (IHF) Mono/Stereo .............................80 dB/75 dB Harmonic Distortion (1 kHz) Mono/Stereo ...................................0.1/0.2% Stereo Separation (1 kHz)......................50 dB Frequency Response 20 Hz to 15 kHz .............................0 ±1.5 dB AM SECTION Tuning Range [U.S.A. and Canada models] ...........................................531 to 1,611 kHz [Australia and General models] ...........................................530 to 1,710 kHz Usable Sensitivity .............................100 µV/m Selectivity ...............................................32 dB Signal-to-Noise Ratio .............................50 dB Image Response Ratio...........................40 dB Spurious Response Ratio.......................50 dB Harmonic Distortion (400 Hz) ..................0.3% AUDIO SECTION Output Level/Impedance FM (100% mod., 1 kHz) .....................................500 mV/2.2 k-ohms AM (30% mod., 400 Hz) .....................................150 mV/2.2 k-ohms GENERAL Power Supply [U.S.A. and Canada models] ............................................AC 120V, 60 Hz [Australia model]..................AC 240V, 50 Hz [General model] ..................AC 110/120/220/240V, 50/60 Hz Power Consumption [U.S.A. and Canada models] ................................................290W/350 VA [Australia and General models] ...........300W AC Outlets 2 SWITCHED OUTLETS [U.S.A., Canada and General models] ..........................................120W max. total 1 SWITCHED OUTLET [Australia model] ...............120W max. total Dimensions (W x H x D) ........................................435 x 146 x 386 mm (17-1/8” x 5-3/4” x 15-3/16”) Weight ..............................10 kg (22 lbs. 0 oz.) Accessories ..........................AM loop antenna Indoor FM antenna Remote control transmitter Batteries User Program Sheets (U.S.A.,Canada and Australia models only) Specifications are subject to change without notice.  YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VS73070