Yamaha MUSICCAST RXA2050 El manual del propietario

Marca: Yamaha

Modelo: MUSICCAST RXA2050

Categoría: Receptores AV

Tipo: El manual del propietario

Este manual también es adecuado para

AV Receiver

Owner's Manual

Read the supplied booklet “Safety Brochure” before using the unit.

CONTENTS

BEFORE USING THE UNIT 4

Accessories................................................................................................ 4

How to use this manual............................................................................ 4

Remote control.......................................................................................... 4

Insert the batteries................................................................................................................................................................... 4

Operating range of the remote control........................................................................................................................... 4

FEATURES 5

What you can do with the unit................................................................. 5

Part names and functions......................................................................... 7

Front panel................................................................................................................................................................................. 7

Front display (indicators)....................................................................................................................................................... 8

Rear panel................................................................................................................................................................................... 9

Remote control....................................................................................................................................................................... 10

PREPARATIONS 11

1 Placing speakers............................................................................... 12

Typical speaker layouts....................................................................................................................................................... 13

Other speaker layouts.......................................................................................................................................................... 14

Setting the speaker impedance....................................................................................................................................... 15

2 Connecting speakers........................................................................ 16

Connecting speaker cables................................................................................................................................................ 17

Connecting the subwoofer (with built-in amplifier)................................................................................................. 17

3 Connecting a TV/playback devices.................................................. 18

Input/output jacks and cables.......................................................................................................................................... 18

Connecting a TV..................................................................................................................................................................... 19

Connecting video devices (such as BD/DVD players).............................................................................................. 20

Connecting audio devices (such as CD players)......................................................................................................... 22

Connecting to the jack on the front panel................................................................................................................... 22

4 Connecting the FM/AM antennas.................................................... 23

5 Connecting the power cable............................................................ 23

6 Selecting an on-screen menu language.......................................... 24

7 Optimizing the speaker settings automatically (YPAO)................ 25

Error messages....................................................................................................................................................................... 27

Warning messages................................................................................................................................................................ 28

PLAYBACK 29

Basic playback procedure...................................................................... 29

Enjoying playback................................................................................................................................................................. 29

Switching information on the front display................................................................................................................. 30

Selecting the input source and favorite settings with one touch

(SCENE).................................................................................................... 31

Selecting a registered scene.............................................................................................................................................. 31

Registering a scene............................................................................................................................................................... 31

Selecting the sound mode..................................................................... 32

Enjoying sound field effects (CINEMA DSP)................................................................................................................. 33

Enjoying unprocessed playback...................................................................................................................................... 35

Enhancing the bass (Extra Bass)....................................................................................................................................... 36

Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed

Music Enhancer)

..................................................................................................................................................................... 36

Listening to FM/AM radio....................................................................... 37

Setting the frequency steps............................................................................................................................................... 37

Selecting a frequency for reception............................................................................................................................... 37

Registering favorite radio stations (presets)................................................................................................................ 38

Radio Data System tuning.................................................................................................................................................. 41

Playing back music stored on a Bluetooth® device.............................. 42

Connecting a Bluetooth® device (pairing).................................................................................................................... 42

Playback of Bluetooth® device contents....................................................................................................................... 43

Disconnecting a Bluetooth® connection....................................................................................................................... 43

Playing back music stored on a USB storage device (Except for USA,

Canada, Australia models)..................................................................... 44

Connecting a USB storage device................................................................................................................................... 44

Playback of USB storage device contents..................................................................................................................... 44

Configuring playback settings for different playback sources

(Option menu)......................................................................................... 47

Option menu items............................................................................................................................................................... 47

CONFIGURATIONS 51

Configuring various functions (Setup Menu)....................................... 51

Setup menu items................................................................................................................................................................. 52

Speaker...................................................................................................................................................................................... 54

HDMI........................................................................................................................................................................................... 57

Sound......................................................................................................................................................................................... 59

ECO............................................................................................................................................................................................. 61

Function.................................................................................................................................................................................... 62

Language.................................................................................................................................................................................. 64

Configuring the system settings (ADVANCED SETUP menu).............. 65

ADVANCED SETUP menu items........................................................................................................................................ 65

Changing the speaker impedance setting (SP IMP.)................................................................................................. 65

Selecting the remote control ID (REMOTE ID)............................................................................................................. 66

Changing the FM/AM tuning frequency setting (TU)............................................................................................... 66

Switching the video signal type (TV FORMAT)............................................................................................................ 66

Selecting the HDMI 4K signal format (4K MODE)....................................................................................................... 66

Restoring the default settings (INIT)............................................................................................................................... 67

Updating the firmware (UPDATE) (Except for USA, Canada, Australia models)............................................. 67

Checking the firmware version (VERSION)................................................................................................................... 67

APPENDIX 68

Frequently asked questions................................................................... 68

Troubleshooting..................................................................................... 69

First, check the following:................................................................................................................................................... 69

Power, system and remote control................................................................................................................................. 69

Audio.......................................................................................................................................................................................... 70

Video.......................................................................................................................................................................................... 72

FM/AM radio............................................................................................................................................................................ 73

USB (Except for USA, Canada, Australia models)........................................................................................................ 73

Bluetooth®................................................................................................................................................................................ 74

Error indications on the front display................................................... 75

Glossary................................................................................................... 76

Audio information................................................................................................................................................................. 76

HDMI and video information............................................................................................................................................. 77

Yamaha technologies.......................................................................................................................................................... 77

Supported devices and file formats...................................................... 78

Supported devices................................................................................................................................................................ 78

File formats.............................................................................................................................................................................. 78

Video signal flow.................................................................................... 78

Information on HDMI.............................................................................. 79

HDMI Control.......................................................................................................................................................................... 79

Audio Return Channel (ARC)............................................................................................................................................. 81

HDMI signal compatibility.................................................................................................................................................. 81

Trademarks............................................................................................. 82

Specifications.......................................................................................... 83

BEFORE USING THE UNIT

Accessories

Check that the following accessories are supplied with the product.

£ AM antenna £ FM antenna

* One of the above is supplied depending on

the region of purchase.

£ YPAO microphone £ Remote control

£ Batteries (AAA, R03, UM-4) (x2)

£ CD-ROM (Owner's Manual

)

£ Easy Setup Guide

£ Safety Brochure

How to use this manual

• Some features are not available in certain regions.

• Due to product improvements, specifications and appearance are subject to

change without notice.

• This manual explains operations using the supplied remote control.

Notice:

Indicates precautions for use to avoid the possibility of malfunction/damage to the unit.

Note:

Indicates instructions and supplementary explanations for optimum use.

Remote control

The supplied remote control is used as follows.

Insert the batteries

Insert the batteries the right way round.

Operating range of the remote control

Point the remote control at the remote control sensor on the unit and remain within the

operating range shown below.

Within 6 m (20 ft)

30° 30°

FEATURES

What you can do with the unit

The unit is equipped with full of useful functions.

Supports 2- to 5.1-channel speaker system

You can enjoy your favorite acoustic spaces in various styles.

YPAO automatically optimizes the speaker settings to suit your room.

• “Optimizing the speaker settings automatically (YPAO)” (p.25)

CINEMA DSP allows you to create stereo or multichannel sounds with

the sound fields like actual movie theaters and concert halls in your

own room.

• “Enjoying sound field effects (CINEMA DSP)” (p.33)

You can enjoy compressed music with enhanced sound (Compressed

Music Enhancer).

• “Playing back digitally compressed formats (such as MP3, etc.) with enriched sound

(Compressed Music Enhancer)”

(p.36)

Change the input source and favorite settings with

one touch (SCENE)

The SCENE function allows you to select the input source and settings registered to

the corresponding scene, such as sound program and Compressed Music Enhancer

on/off, with just one touch.

• “Selecting the input source and favorite settings with one touch (SCENE)” (p.31)

4K Ultra HD signal and HDCP 2.2 supported

You can enjoy the high definition video quality of 4K with HDCP 2.2 that complies with

the latest copyright protection.

• “Selecting the HDMI 4K signal format (4K MODE)” (p.66)

The ECO mode (power saving function) allows you to

create an eco-friendly home theater system

When the ECO mode is enabled, you can reduce the unit's power consumption.

• “ECO Mode” (p.61)

Sequential operation of a TV, AV receiver, and

BD/DVD player (HDMI Control)

When the unit is connected to an HDMI Control-compatible TV and BD/DVD player

with each HDMI cable, you can control the unit (such as power and volume) and

BD/DVD player with TV remote control operations.

• “HDMI Control” (p.79)

Supports Bluetooth® devices

You can play back music stored on a Bluetooth device.

• “Playing back music stored on a Bluetooth

device” (p.42)

Supports USB storage devices

You can play back music stored on a USB storage device.

• “Playing back music stored on a USB storage device (Except for USA, Canada,

Australia models)” (p.44)

Connecting various devices

A number of HDMI jacks and various input/output jacks on the unit allow you to

connect video devices (such as BD/DVD players), audio devices (such as CD

players), game consoles, portable audio player, and other devices.

• “Connecting a TV/playback devices” (p.18)

Playing back TV audio in surround sound with a

single HDMI cable connection (Audio Return

Channel: ARC)

When using an ARC -compatible TV, you only need one HDMI cable to enable video

output to the TV, audio input from the TV, and the transmission of HDMI Control

signals.

• “Connecting a TV” (p.19)

Surround playback with 5 speakers placed in front

You can enjoy the surround sound even when the surround speakers are placed in

front.

• “Enjoying sound field effects without surround speakers (Virtual CINEMA

DSP)” (p.34)

Enhanced bass reproduction

Extra Bass allows you to enjoy enhanced bass reproduction that does not depend on

the speakers used.

• “Enhancing the bass (Extra Bass)” (p.36)

Listening to FM/AM radio

The unit is equipped with a built-in FM/AM tuner. You can register up to 40 favorite

radio stations as presets.

• “Listening to FM/AM radio” (p.37)

Easy operation with a TV screen

You can operate the USB storage device, view information, or easily configure the

settings using the on-screen menu.

Auto Rename function

The unit creates an input source name, displayed on the front display, automatically

according to the connected HDMI-compatible device.

• “Input Rename” (p.62)

Useful applications

The useful application for connections and operations of the unit is as follows.

Application for tablets “AV SETUP GUIDE”

AV SETUP GUIDE is an application that assists you with cable connections

between AV Receiver

and source devices as well as AV Receiver setup. This

app guides you through the various settings such as speaker connections, TV

and source device connections.

Functions:

1) Connection support guide

– Speaker connection

– TV/source devices connection

2) Setup support guide

– Various setup assistance with illustrations.

– YPAO setting guidance

3) View Owner's Manual

* This application is for tablets only.

For details, search for “AV SETUP GUIDE” on the App Store or Google Play™.

Part names and functions

The part names and functions of the unit and the supplied remote control are as follows.

Front panel

YPAO MIC

INFO

MEMORY

(

PAIRING

)

PRESET

FM AM

TUNING

PHONES

SILENT

CINEMA

VOLUME

AUX

TONE

CONTROL

STRAIGHT

DVD

RADIO

INPUT

PROGRAM

SCENE

AUDIO

USB

3 94 521 6 7 8

B D E

HF GA C

z (power) key

Turns on/off (standby) the unit.

YPAO MIC jack

For connecting the supplied YPAO microphone (p.25).

Remote control sensor

Receives remote control signals (p.4).

INFO key

Selects the information displayed on the front display

(p.30).

MEMORY (PAIRING) key

Registers FM/AM radio stations as preset stations (p.38).

Starts pairing with a Bluetooth device by holding down for 3

seconds (p.42).

PRESET keys

Select a preset FM/AM radio station (p.40).

FM and AM keys

Switch between FM and AM (p.37).

TUNING keys

Select the radio frequency (p.37).

Front display

Displays information (p.8).

PHONES jack

For connecting headphones.

INPUT keys

Select an input source.

TONE CONTROL key

Adjusts the high-frequency range and low-frequency range

of output sounds (p.

48).

SCENE keys

Select the registered input source and sound program with

one touch. Also, turns on the unit when it is in standby

mode (p.31).

PROGRAM keys

Select a sound program or a surround decoder (p.32).

STRAIGHT key

Enables/disables the straight decode mode (p.35).

AUX jack

For connecting devices, such as portable audio players

(p.22).

USB jack

For connecting a USB storage device (p.44).

VOLUME knob

Adjusts the volume.

Front display (indicators)

L C R

SL SW SR

VOL.

MUTE

ENHANCER

TUNEDSTEREO

SLEEP

OUT

ADAPTIVE DRC

6 7 8

2 5

HDMI

Lights up when HDMI signals are being input or output.

OUT

Lights up when HDMI signals are being output.

ENHANCER

Lights up when Compressed Music Enhancer (p.36) is

working.

CINEMA DSP

Lights up when CINEMA DSP (p.33) is working.

STEREO

Lights up when the unit is receiving a stereo FM radio

signal.

TUNED

Lights up when the unit is receiving an FM/AM radio station

signal.

Bluetooth indicator

Light up while the unit is connecting to a Bluetooth device.

SLEEP

Lights up when the sleep timer is on.

MUTE

Blinks when audio is temporarily muted.

Volume indicator

Indicates the current volume.

ECO

Lights up when the eco mode (p.61) is enabled.

Cursor indicators

Indicate the remote control cursor keys currently

operational.

Information display

Displays the current status (such as input name and sound

mode name). You can switch the information by pressing

INFO (p.

30).

Speaker indicators

Indicate speaker terminals from which signals are output.

A Front speaker (L)

S Front speaker (R)

D Center speaker

F Surround speaker (L)

G Surround speaker (R)

L Subwoofer

ADAPTIVE DRC

Lights up when Adaptive DRC (p.48) is working.

Rear panel

8 95 7

▪ The area around the video/audio output jacks is marked in white

on the actual product to prevent improper connections.

HDMI OUT jack

For connecting to an HDMI-compatible TV and outputting

video/audio signals (

p.18). When using ARC, TV audio

signal can also be input through the HDMI OUT jack.

HDMI 1–4 jacks

For connecting to HDMI-compatible playback devices and

inputting video/audio signals (

p.19).

ANTENNA jacks

For connecting to FM and AM antennas (p.23).

Power cable

For connecting to an AC wall outlet (p.23).

AV jacks

AUDIO jacks

For connecting to video/audio playback devices and

inputting video/audio signals (

p.20).

MONITOR OUT jacks

For connecting to a TV and outputting video signals

(p.18).

SUBWOOFER PRE OUT jack

For connecting to a subwoofer (with built-in amplifier)

(p.16).

SPEAKERS terminals

For connecting to speakers (p.16).

VOLTAGE SELECTOR

(Taiwan, Brazil and General models only)

Selects the switch position according to your local voltage

(p.23).

Remote control

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROG RAM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPUT

DVD

S C E NE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

Remote control signal transmitter

Transmits infrared signals.

SLEEP key

Pressing this key repeatedly will specify the time (120 min,

90 min, 60 min, 30 min, off), in which the unit switches to

the standby mode.

SCENE keys

Select the registered input source and sound program with

one touch. Also, turn on the unit when it is in standby mode

(p.31).

Sound mode keys

Select a sound mode (p.32).

Input selection keys

Select an input source for playback.

SETUP key

Displays the setup menu (p.51).

Menu operation keys

Cursor keys

Select a menu or the parameter.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen.

789 External device operation keys

Let you perform playback operations when “USB” is

selected as the input source, or control playback of the

HDMI Control-compatible playback device.

Note

▪ The playback devices must support HDMI Control. Some

HDMI Control-compatible devices cannot be used.

▪ You can assign the unit's functions to the RED/GREEN/

YELLOW/BLUE keys (

p.64).

Radio keys

Operate the FM/AM radio when “TUNER” is selected as the

input source (p.37).

MEMORY

Registers FM/AM radio stations as

presets.

PRESET

Select a preset station.

TUNING

Select the radio frequency.

z (receiver power) key

Turns on/off (standby) the unit.

VOLUME keys

Adjust the volume.

MUTE key

Mutes the audio output.

OPTION key

Displays the option menu (p.47).

PREPARATIONS

General setup procedure

1 Placing speakers................................................................................................................................ (p.12)

2 Connecting speakers........................................................................................................................ (p.16)

3 Connecting a TV/playback devices.................................................................................................. (p.18)

4 Connecting the FM/AM antennas.................................................................................................... (p.23)

5 Connecting the power cable............................................................................................................ (p.23)

6 Selecting an on-screen menu language.......................................................................................... (p.24)

7 Optimizing the speaker settings automatically (YPAO)................................................................ (p.25)

This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!

1 Placing speakers

Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer in your room. This section describes the representative speaker

layout examples.

Notice

▪ (U.S.A. and Canada models only)

Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6

Ω MIN”. For details, see “Setting the speaker impedance” (p.15).

▪ (Except for U.S.A. and Canada models)

Use speakers with an impedance of at least 6 W.

▪ Use a subwoofer with built-in amplifier.

▪ Be sure to connect the front left and right speakers.

Typical speaker layouts

5.1-channel system

We recommend this speaker layout which can maximize the performance of the unit.

4 5

1 2

10° to 30° 10° to 30°

Speaker type Abbr. Function

Front (L/R)

1/2

Produce front left/right channel sounds (stereo sounds).

Center

Produces center channel sounds (such as movie dialogue

and vocals).

Surround (L/R)

4/5

Produce surround left/right channel sounds.

Subwoofer

Produces LFE (low-frequency effect) channel sounds and

reinforces the bass parts of other channels.

This channel is counted as “0.1”.

Note

▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system).

▪ You can place the subwoofer either in the left or right side.

5.1-channel system (Virtual CINEMA FRONT)

We recommend this speaker layout when the speakers can't be placed in back of the

room.

1 2

4 5

Speaker type Abbr. Function

Front (L/R)

1/2

Produce front left/right channel sounds (stereo sounds).

Center

Produces center channel sounds (such as movie dialogue

and vocals).

Surround (L/R)

4/5

Produce surround left/right channel sounds. By this

system, place the surround speakers in front.

Subwoofer

Produces LFE (low-frequency effect) channel sounds and

reinforces the bass parts of other channels.

This channel is counted as “0.1”.

Note

▪ To utilize this configuration, set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On”.

▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system).

▪ You can place the subwoofer either in the left or right side.

Other speaker layouts

The following speaker layouts are also available.

3.1-channel system

1 2

2.1-channel system

1 2

Setting the speaker impedance

(U.S.A. and Canada models only)

Under its default settings, the unit is configured for 8-ohm speakers. When connecting

6-ohm speakers, set the speaker impedance to “6 Ω MIN”.

Before connecting speakers, connect the power cable to an AC

wall outlet.

While holding down STRAIGHT on the front panel, press z

(power).

(power)

STRAIGHT

Check that “SP IMP.” is displayed on the front display.

1 2

PARTY

VIRTUAL

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

ZONE

2 A

ZONE

3 B

SP IMP.••8¬MIN

Press STRAIGHT to select “6 Ω MIN”.

Press z (power) to set the unit to standby mode and remove the

power cable from the AC wall outlet.

You are now ready to connect the speakers.

2 Connecting speakers

Connect the speakers placed in your room to the unit. The following diagrams provide connections for a 5.1-channel system as an example. For other systems, connect speakers

while referring to the connection diagram for the 5.1-channel system.

Notice

▪ Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before connecting the speakers.

▪ The speaker has the polarity (+/-). Connect the speaker cable correctly between the positive (+) terminal of the unit and the speaker, and also between the negative (-) terminal of them.

Cables required for connection (commercially available)

Speaker cables (x the number of speakers)

–

Audio pin cable (x1: for connecting a subwoofer)

5 4

3 2 1

The unit (rear)

10 mm (3/8”)

Audio pin cable

Use a subwoofer with built-in amplifier.

Subwoofer Surround (L)Surround (R) Center Front (R) Front (L)

10 mm (3/8”)

Precaution for connecting of the speaker cables

Improper connecting of the speaker cables may cause short circuit and

also damage the unit or the speakers.

▪ Twist the bare wires of the speaker cables

firmly together.

▪ Do not let the core wires of the speaker cable

touch one another.

▪ Do not let the core wires of the speaker cable

come into contact with the unit’s metal parts

(rear panel and screws).

If “Check SP Wires” appear on the front display when the unit is turned

on, turn off the unit, and then check the speaker cables short circuit.

Connecting speaker cables

Speaker cables have two wires. One is for connecting the negative (-) terminal of the

unit and the speaker, and the other is for the positive (+) terminal. If the wires are

colored to prevent confusion, connect the black wire to the negative and the other wire

to the positive terminal.

Connecting front speakers

Remove approximately 10 mm (3/8”) of insulation from the ends of

the speaker cable, and twist the bare wires of the cable firmly

together.

Loosen the speaker terminal.

Insert the bare wires of the cable into the gap on the side (upper

right or bottom left) of the terminal.

Tighten the terminal.

FRONT

+ (red)

- (black)

Using a banana plug

(U.S.A., Canada, Australia, Taiwan, Brazil and General models only)

Tighten the speaker terminal.

Insert a banana plug into the end of the terminal.

FRONT

Banana plug

Connecting center/surround speakers

Remove approximately 10 mm (3/8”) of insulation from the ends of

the speaker cable, and twist the bare wires of the cable firmly

together.

Press down the tab.

Insert the bare wires of the cable into the hole in the terminal.

Release the tab.

SURROUND

CENTER

+ (red)

- (black)

Connecting the subwoofer (with built-in amplifier)

Use an audio pin cable to connect the subwoofer.

AV 2

AV 3

Audio pin cable

3 Connecting a TV/playback devices

The unit is equipped with a variety of input jacks

including HDMI input jacks to allow you to connect

different types of playback devices. For information on

how to connect a Bluetooth device or a USB storage

device, see the following pages.

• Connecting a Bluetooth device (p.42)

• Connecting a USB storage device (p.44)

Input/output jacks and cables

Video/audio jacks

HDMI jacks

Transmit digital video and digital sound through a

single jack. Use an HDMI cable.

HDMI cable

Note

▪ Use a 19-pin HDMI cable with the HDMI logo. We

recommend using a cable less than 5.0 m (16.4 ft) long to

prevent signal quality degradation.

▪ The unit’s HDMI jacks support the HDMI Control, Audio

Return Channel (ARC), and 3D and 4K Ultra HD video

transmission (through output) features.

▪ Use high speed HDMI cables to enjoy 3D or 4K Ultra HD

videos.

Video jacks

VIDEO jacks

Transmit analog video signals. Use a video pin

cable.

Video pin cable

Audio jacks

OPTICAL jacks

Transmit digital audio signals. Use a digital optical

cable. Remove the tip protector (if available) before

using the cable.

OPTICAL

Digital optical cable

COAXIAL jacks

Transmit digital audio signals. Use a digital coaxial

cable.

Digital coaxial cable

AUDIO jacks

(Stereo L/R jacks)

Transmit analog stereo audio signals. Use a stereo

pin cable (RCA cable).

Stereo pin cable

(Stereo mini jack)

Transmits analog stereo audio signals. Use a

stereo mini-plug cable.

Stereo mini-plug cable

Connecting a TV

Connect a TV to the unit so that video input to the unit can be output to the TV. You

can also enjoy playback of TV audio on the unit.

To maximize the performance of the unit, we recommend connecting a TV with an

HDMI cable.

HDMI connection

Connect the TV to the unit with an HDMI cable and a digital optical cable.

HDMI

AUDIO 1

(

)

OPTICAL

O O

HDMI

AUDIO 1

(

)

OPTICAL

O O

The unit (rear)

AUDIO 1 (OPTICAL) jack

HDMI OUT jack HDMI input

Audio output

(digital optical)

Note

▪ You do not make a digital optical cable connection between the TV and the unit in the following cases:

– If your TV supports Audio Return Channel (ARC)

– If you will receive TV broadcasts only from the set-top box

▪ If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s

power and volume with the TV’s remote control.

To use HDMI Control and ARC, you need to configure the HDMI settings on the unit.

For details on the settings, see “Information on HDMI”

(p.79).

About Audio Return Channel (ARC)

▪ ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a

single HDMI cable, you can output video/audio to the TV or input TV audio to the unit.

▪ When using ARC, connect a TV with an HDMI cable that supports ARC.

Composite video connection

When connecting any video device with a video pin cable, connect the TV to the

MONITOR OUT

(VIDEO) jack.

Note

▪ If you connect your TV to the unit with a cable other than HDMI, video input to the unit via HDMI cannot be

output to the TV.

▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI.

▪ If you will receive TV broadcasts only from the set-top box, you do not need to make an audio cable

connection between the TV and the unit.

VIDEO (composite video) connection

Connect the TV to the unit with a video pin cable and a digital optical cable.

VIDEO

AUDIO 1

(

)

OPTICAL

O O

MONITOR

OUT

The unit (rear)

AUDIO 1 (OPTICAL) jack

MONITOR OUT (VIDEO) jack

Video input

(composite video)

Audio output

(digital optical)

Connecting video devices (such as BD/DVD players)

Connect video devices such as BD/DVD players, set-top boxes (STBs) and game

consoles to the unit. Depending on the video/audio output jacks available on your

video device, choose one of the following connections. We recommend using an

HDMI connection if the video device has an HDMI output jack.

Note

If the combination of video/audio input jacks available on the unit does not match your video device, change

its combination according to the output jacks of your device (p.21).

HDMI connection

Connect a video device to the unit with an HDMI cable.

HDMI

The unit (rear)

HDMI OUT jack

HDMI 1–4 jacks

Video device

If you select HDMI 1–4 as the input source by pressing INPUT, the video/audio played

back on the video device will be output from the unit.

Note

To watch videos input to the HDMI 1–4 jacks, you need to connect your TV to the HDMI OUT jack of the unit

(p.19).

Composite video connection

Connect a video device to the unit with a video pin cable and an audio cable (digital

coaxial or stereo pin cable). Choose a set of input jacks (on the unit) depending on the

audio output jacks available on your video device.

Output jacks on video device

Input jacks on the unit

Video Audio

Composite video

Digital coaxial AV 1 (VIDEO + COAXIAL)

Analog stereo AV 2–3 (VIDEO + AUDIO)

Digital optical

You need to change the combination

of video/audio input jacks (p.21).

COAXIAL

VIDEO

C C

The unit (rear)

AV 1 (COAXIAL) jack or AV 2–3

(AUDIO) jacks

AV 1–3 (VIDEO) jacks

Video output

(composite video)

Audio output

(digital coaxial or analog

stereo)

Video device

If you select AV 1-3 as the input source by pressing INPUT, the video/audio played

back on the video device will be output from the unit.

Note

To watch videos input to the AV 1–3 (VIDEO) jacks, you need to connect your TV to the MONITOR OUT

(VIDEO) jack of the unit (p.19).

Changing the combination of video/audio input jacks

If the combination of video/audio input jacks available on the unit does not match your

video device, change its combination according to the output jacks of your device.

You can connect a video device that has the following video/audio output jacks.

Output jacks on video device Input jacks on the unit

Video Audio Video Audio

HDMI

Digital optical HDMI 1–4 AUDIO 1 (OPTICAL)

Digital coaxial HDMI 1–4

AUDIO 2 (COAXIAL)

AV 1 (COAXIAL)

Analog stereo HDMI 1–4 AV 2–3 (AUDIO)

Composite video Digital optical AV 1–3 (VIDEO) AUDIO 1 (OPTICAL)

Necessary setting

For example, if you have connected a video device to AV 2 (VIDEO) and AUDIO 1

(OPTICAL) jack of the unit, change the combination setting as follows.

VIDEO

AUDIO 1

(

)

OPTICAL

O O

The unit (rear)

AUDIO 1 (OPTICAL) jack

AV 2 (VIDEO) jack

Video output

(composite video)

Audio output

(digital optical)

Video device

After connecting external devices (such as a TV and playback

devices) and power cable of the unit, turn on the unit.

Press INPUT to select “AV 2” (video input jack to be used) as

the input source.

Press OPTION.

MUTE

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

MUTE

P MENU

HOME

POP-UP/MENU

DISPLA

DISPLADISPLA

DISPLA

DISPLADISPLA

DISPLA

RETURN

RETURNRETURN

RETURN

SETU

OPTION

ENTER

Cursor keys

Use the cursor keys (q/w) to select “Audio In” and press

ENTER.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Audio In

VOL.

Use the cursor keys (e/r) to select “AUDIO 1” (audio input

jack to be used).

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Audio••AUDIO 1

VOL.

Press OPTION.

This completes the necessary settings.

If you select “AV 2” as the input source by pressing INPUT, the video/audio

played back on the video device will be output from the unit.

Connecting audio devices (such as CD players)

Connect audio devices such as CD players and MD players to the unit. Depending on

the audio output jacks available on your audio device, choose one of the following

connections.

Audio output jacks on audio device Audio input jacks on the unit

Digital optical AUDIO 1 (OPTICAL)

Digital coaxial

AUDIO 2 (COAXIAL)

AV 1 (COAXIAL)

Analog stereo AV 2–3 (AUDIO)

COAXIAL

OPTICAL

COAXIAL

OPTICAL

C C

O O

The unit (rear)

AV 1–3 jacks

AUDIO 1–2 jacks

Audio output

(either digital optical, digital coaxial,

or analog stereo)

Audio device

If you select AV 1-3 or AUDIO 1-2 as the input source by pressing INPUT, the audio

played back on the audio device will be output from the unit.

Connecting to the jack on the front panel

Use the AUX jack on the front panel to temporarily connect devices such as portable

audio players to the unit.

Before making a connection, stop playback on the device and turn down the volume

on the unit.

AUX

TONE

CONTROL

STRAIGHT

DVD

RADIO

INPUT

PROGRAM

AUDIO

USB

The unit (front)

Portable audio player

If you select “AUX” as the input source by pressing INPUT, the audio played back on

the device will be output from the unit.

Note

▪ You need to prepare the audio cable that matches the output jacks on your device.

▪ For details on how to connect a USB storage device, see “Connecting a USB storage device” (p.44).

4 Connecting the FM/AM antennas

Connect the supplied FM/AM antennas to the unit.

Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.

The unit (rear)

FM antenna

AM antenna

Assembling and connecting the AM antenna

ReleaseHold down Insert

Note

▪ Unwind only the length of cable needed from the AM antenna unit.

▪ The wires of the AM antenna have no polarity.

5 Connecting the power cable

Warning

(Taiwan, Brazil and General models only)

Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall

outlet. Improper setting of

VOLTAGE SELECTOR

may cause damage to the unit and create a potential

fire hazard.

Before connecting the power cable

Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110–

120/220–240 V, 50/60 Hz.

VOLTAGE

SELECTOR

110V

–

120V

220V

–

240V

The unit (rear) VOLTAGE SELECTOR

After all the connections are complete, plug in the power cable.

The unit (rear)

To an AC wall outlet

6 Selecting an on-screen menu language

Select the desired on-screen menu language.

Press z (receiver power) to turn on the unit.

Turn on the TV and switch the TV input to display video from the

unit (HDMI OUT jack).

Note

Operations with TV screen are available only when your TV is connected to the unit via HDMI. If

not, carry out operations while viewing the front display.

Press SETUP.

Use the cursor keys to select “Language” and press ENTER.

Setup

Speaker

HDMI

Sound

ECO

Function

Language

Back

RETURN

Use the cursor keys to select the desired language.

Language

English

Français

Deutsch

Español

Русский

Italiano

To exit from the menu, press SETUP.

Note

The information on the front display is provided in English only.

7 Optimizing the speaker settings automatically (YPAO)

The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker

connections, measures the distances from them to your listening position(s), and then

automatically optimizes the speaker settings, such as volume balance and acoustic

parameters, to suit your room.

Note

▪ When you use the front 5.1-channel speaker (Virtual CINEMA FRONT) configuration (p.13), set “Virtual

CINEMA FRONT” (p.55) in the “

Setup

” menu to “On” beforehand.

▪ Please note the following when using YPAO.

– Use YPAO after connecting a TV and speakers to the unit.

– During the measuring process, test tones are output at high volume. Ensure that the test tones do not

frighten small children.

– During the measuring process, you cannot adjust the volume.

– During the measuring process, keep the room as quiet as possible.

– Do not connect headphones.

– Do not stand between the speakers and the YPAO microphone during the measurement process (about

3 minutes).

Press z (receiver power) to turn on the unit.

Turn on the TV and switch the TV input to display video from the

unit (HDMI OUT jack).

Note

Operations with TV screen are available only when your TV is connected to the unit via HDMI. If

not, carry out operations while viewing the front display.

Turn on the subwoofer and set the volume to half. If the crossover

frequency is adjustable, set it to maximum.

VOLUME HIGH CUT

CROSSOVER/

MIN MAXMIN MAX

Place the YPAO microphone at your listening position and

connect it to the YPAO MIC jack on the front panel.

Note

Place the YPAO microphone at your listening position (same height as your ears). We recommend

the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the

microphone.

1 2

4 5

The unit (front)

Ear height

The following screen appears on the TV.

Auto Setup

Start

Exit

To start the measurement, use the cursor keys to select “Start”

and press ENTER.

The measurement will start in 10 seconds. Press ENTER to start the

measurement immediately.

Note

To stop the measurement temporarily, press RETURN and follow the procedure in “Error

messages”

(p.27).

The following screen appears on the TV when the measurement finishes.

Auto Setup

Meaurement Finished

Result

3 / 2 / 0.1 ch

3.0 / 10.5 m

-3.0 / +10.0 dB

ENTER

The number of speakers (front side/rear side/subwoofer)

Speaker distance (nearest/farthest)

Adjustment range of speaker output level

Warning message (if available)

Note

▪ If any error message (such as E-1) or warning message (such as W-1) appears, see “Error

messages”

(p.27)

or “Warning messages” (p.28).

▪ A speaker with a problem is indicated by blinking of the speaker indicators in the front display.

▪ If multiple warnings are given (when operating with the front display), use the cursor keys (q/w)

to check the other warning messages.

Confirm the results displayed on the screen and press ENTER.

Use the cursor keys (e/r) to select “SAVE” and press ENTER.

Auto Setup

Start

Exit < SAVE >

The adjusted speaker settings are applied.

Note

To finish the measurement without saving the result, select “CANCEL”.

Disconnect the YPAO microphone from the unit.

This completes optimization of the speaker settings.

Notice

▪ The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be

exposed to direct sunlight or high temperatures (such as on top of AV equipment).

Error messages

If any error message is displayed during the measurement, resolve the problem and

perform YPAO again.

Auto Setup

ERROR

E-9 : User Cancel

< RETRY >

2 %

Error message

TV screen

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

E-5:NOISY

VOL.

Front display

Procedure to handle errors

Check the content of error message and press ENTER.

Use the cursor keys (e/r) to select the desired operation.

To exit the YPAO measurement:

Select “EXIT” and press ENTER.

Use the cursor keys (q/w) to select “Exit” and press ENTER.

Disconnect the YPAO microphone from the unit.

To retry the YPAO measurement from beginning:

Select “RETRY” and press ENTER.

To proceed with the current YPAO measurement (for E-5 and E-9

only):

Select “PROCEED” and press ENTER.

Error message Cause Remedy

E-1:No Front SP

(E-1:NO FRNT SP)

Front speakers are not

detected.

Exit YPAO, turn off the unit, and then

check the speaker connections.

E-2:No Sur. SP

(E-2:NO SUR SP)

One of the surround

speakers cannot be

detected.

E-5:Noisy

(E-5:NOISY)

The noise is too loud.

Keep the room quiet and retry YPAO. If

you select “PROCEED”, YPAO takes the

measurement again and ignores any

noise detected.

E-7:No MIC

(E-7:NO MIC)

The YPAO microphone has

been removed.

Connect the YPAO microphone to the

YPAO MIC

jack firmly and retry YPAO.

E-8:No Signal

(

E-8:NO SIGNAL)

The YPAO microphone

cannot detect test tones.

Connect the YPAO microphone to the

YPAO MIC

jack firmly and retry YPAO. If

this error occurs repeatedly, contact the

nearest authorized Yamaha dealer or

service center.

E-9:User Cancel

(E-9:CANCEL)

The measurement has been

canceled.

Retry or exit YPAO as necessary.

E-10:Internal Err.

(E-10:INTERNAL)

An internal error has

occurred.

Exit YPAO, and turn off and on the unit. If

this error occurs repeatedly, contact the

nearest authorized Yamaha dealer or

service center.

Note

Texts in parentheses denote indicators on the front display.

Warning messages

If a warning message is displayed after the measurement, you can still save the

measurement results by following on-screen instructions.

However, we recommend you perform YPAO again in order to use the unit with the

optimal speaker settings.

Auto Setup

Meaurement Finished

Result

3 / 2 / 0.1 ch

3.0 / 10.5 m

-3.0 / +10.0 dB

W-1 : Out of Phase

ENTER

Warning message

TV screen

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

W-1:PHASE

VOL.

Problem speaker (blinks)

Front display

Procedure to handle warnings

Check the content of warning message and press ENTER.

Use the cursor keys (e/r) to select the desired operation.

To save the measurement results:

Select “SAVE” and press ENTER.

To discard the measurement result:

Select “CANCEL” and press ENTER.

Disconnect the YPAO microphone from the unit.

Warning message Cause Remedy

W-1:Out of Phase

(W-1:PHASE)

A speaker cable may be

connected with the reverse

polarity (+/-).

Check the cable connections (+/-) of the

problem speaker.

If the speaker is connected incorrectly:

Turn off the unit, reconnect the speaker

cable.

If the speaker is connected correctly:

Depending on the type of speakers or

room environment, this message may

appear even if the speakers are

connected correctly. In this case, you

can ignore the message.

W-2:Over Distance

(W-2:DISTANCE)

A speaker is placed more

than 24 m (80 ft) from the

listening position.

Exit YPAO, turn off the unit, and place the

problem speaker within 24 m (80 ft) of the

listening position.

W-3:Level Error

(W-3:LEVEL)

There are significant volume

differences between the

speakers.

Check the usage environment and cable

connections (+/-) of each speaker, and

the volume of the subwoofer. If there is

any problem, exit YPAO, turn off the unit,

and then reconnect speaker cable or

correct the speaker positions. We

recommend using the same speakers or

speakers with specifications that are as

similar as possible.

Note

Texts in parentheses denote indicators on the front display.

PLAYBACK

Basic playback procedure

Enjoying playback

Turn on the external devices (such as a TV or BD/DVD player)

connected to the unit.

Use the input selection keys to select an input source.

MUTE

FM/AM

VOLUME

PROG RAM

USB

BLUETOOTH

INPUT

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

OG R

VOLUME

MUTE

Input selection keys

Start playback on the external device or select a radio station.

Refer to the instruction manual for the external device.

For details on the following operations, see the corresponding pages.

▪ “Listening to FM/AM radio” (p.37)

▪ “Playing back music stored on a Bluetooth

device” (p.42

)

▪ “Playing back music stored on a USB storage device (Except for USA,

Canada, Australia models)”

(p.44)

Press VOLUME to adjust the volume.

Note

▪ To mute the audio output, press MUTE. Press MUTE again to unmute.

▪ To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL on the front panel

(p.48).

Switching information on the front display

Press INFO repeatedly to select between the various display

items.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Audio Decoder

VOL.

Item name

About 3 seconds after a display item is selected, its corresponding

information appears.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

†‡Pro Logic

VOL.

Information

Note

Available items vary depending on the selected input source. The displayed item can also be

applied separately to each input source.

Currently input source Item

HDMI

AUDIO

AUX

Bluetooth

Input (input source name), DSP Program (sound mode name), Audio

Decoder (decoder name*)

USB

Song (song title), Artist (artist name), Album (album name), DSP

Program (sound mode name), Audio Decoder (decoder name*)

TUNER

Frequency (frequency), DSP Program (sound mode name), Audio

Decoder (decoder name*)

(U.K. and Europe models only)

Radio Data System data is also available when the unit is tuned into a

Radio Data System broadcasting station (p.41).

* The name of the audio decoder currently activated is displayed. If no audio decoder

is activated, “Decoder Off” appears.

Selecting the input source and favorite settings with one touch (SCENE)

The SCENE function allows you to select the assigned input source, sound program,

and Compressed Music Enhancer on/off with just one touch.

Selecting a registered scene

Press SCENE.

The input source and settings registered to the corresponding scene are

selected. The unit turns on automatically when it is in standby mode.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

PROG RAM

STRAIGHT

ENHANCER BASS

DVD

S C E NE

RADIO

SLEEP

OG R

IGHT

ENHANCER

SLEE

SCENE

By default, the following settings are registered for each scene.

SCENE

Input

HDMI1 AUDIO1 AUDIO2 TUNER

Sound program

MOVIE (Sci-Fi) STRAIGHT STRAIGHT

STEREO

(5ch Stereo

)

Compressed Music

Enhancer

Off On Off On

SCENE link playback

On On Off Off

Note

The SCENE link playback function allows you to automatically turn on the TV or start playback of an external

device connected to the unit via HDMI, in conjunction with a scene selection. To enable

SCENE link

playback, set “SCENE” (p.58) in the “Setup” menu to “On”.

Registering a scene

Perform the following operations to prepare the settings you want

to assign to a scene.

▪ Select an input source (p.29)

▪ Select a sound program (p.32) or straight decode (p.35)

▪ Enable/disable Compressed Music Enhancer (p.36)

Hold down the desired SCENE key until “SET Complete” appears

on the front display.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

SET Complete

VOL.

Selecting the sound mode

The unit is equipped with a variety of sound programs and surround decoders that

allow you to enjoy playback sources with your favorite sound mode (such as sound

field effect or stereo playback).

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

PROG RAM

STRAIGHT

ENHANCER BASS

DVD

S C E NE

RADIO

SLEEP

S C E N

ADIO

SLEE

STRAIGHT

ENHANCER

BASS

PROGRAM

I want to enjoy viewing video sources such as movies, TV programs, or

games.

• Select a sound program suitable for each video source by pressing PROGRAM

repeatedly (

p.33).

I want to enjoy listening to music sources or stereo playback.

• Select a sound program suitable for music or stereo playback by pressing

PROGRAM

repeatedly (p.34).

I want to enjoy multichannel playback from 2-channel sources.

• Select a surround decoder in the “Option” menu (p.47).

I want to enjoy unprocessed sounds in original channels.

• Switch to the straight decode mode by pressing STRAIGHT (p.35).

I want to enjoy enhanced bass sounds.

• Enable Extra Bass by pressing BASS (p.36).

I want to enjoy listening to compressed music.

• Enable Compressed Music Enhancer by pressing ENHANCER (p.36).

This mode lets you enjoy compressed music stored on a Bluetooth device or USB

storage device with additional depth and breadth (p.36).

Note

▪ The sound mode can be applied separately to each input source.

▪ When you play back audio signals with a sampling rate of higher than 96 kHz, the straight decode mode

(p.35) is automatically selected.

▪ You can check which speakers are currently outputting sound by looking at the speaker indicators on the

unit’s front panel (p.8).

Enjoying sound field effects (CINEMA DSP)

The unit is equipped with a variety of sound programs that utilize Yamaha’s original

DSP technology (CINEMA DSP). It allows you to easily create sound fields like actual

movie theaters or concert halls in your room.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Sci-Fi

VOL.

Sound program category

“CINEMA DSP” lights up

Sound program

Note

You can adjust the sound field effect level in “DSP Level (DSP Level)” (p.48) in the “Option” menu.

Sound programs suitable for movies (MOVIE)

The following sound programs are optimized for viewing video sources, such as

movies, TV programs, and games.

Standard

This program creates a sound field that emphasizes the surround feeling

without disturbing the original acoustic positioning of multichannel audio,

such as Dolby Digital and DTS. Its design is based on the concept of the

ideal movie theater, in which the audience is surrounded by beautiful

reverberations from the left, right, and rear.

Spectacle

This program delivers the scale and grandeur of spectacular movie

productions. It delivers an expansive sound space to match the

cinemascope wide-screen, and boasts a broad dynamic range,

providing everything from small delicate sounds to powerful loud booms.

Sci-Fi

This program clearly reproduces the finely elaborated sound design of

the latest Sci-Fi and SFX movies. You can enjoy a variety of

cinematographically created virtual spaces reproduced with clear

separation between dialogue, sound effects, and background music.

Adventure

This program is ideal for reproducing the sound design of action and

adventure movies precisely. The sound field restrains reverberations, but

puts emphasis on reproducing a sensation of expansiveness on both

sides, powerful space expanded widely to the left and right. The

restrained depth creates a clear and powerful space, while also

maintaining the articulation of the sounds and the separation of the

channels.

Drama

This program features stable reverberations that match a wide range of

movie genres, from serious dramas to musicals and comedies. The

reverberations are modest, but suitably stereophonic. The sound effects

and background music are reproduced with a gentle echo that does not

impinge on the articulation of the dialogue. You’ll never get tired listening

for long periods.

Mono Movie

This program reproduces monaural video sources, such as classic

movies, in an atmosphere of a good old movie theater. The program

creates a pleasant space with depth, by adding breadth and the

appropriate reverberation to the original audio.

Sports

This program allows listeners to enjoy the rich vividness of sport

broadcasts and light entertainment programs. In sports broadcasts, the

commentators’ voices are positioned clearly at the center, while the

atmosphere inside the stadium is realistically conveyed by the peripheral

delivery of the sounds of the fans in a suitable space.

Action Game

This program is suitable for action games, such as car racing and

fighting games. The reality of, and emphasis on, various effects makes

the player feel like they are right in the middle of the action, allowing for

greater concentration. Use this program in combination with Compressed

Music Enhancer for a more dynamic and strong sound field.

Roleplaying Game

This program is suitable for role-playing and adventure games. This

program adds depth to the sound field for natural and realistic

reproduction of background music, special effects, and dialogue from a

wide variety of scenes. Use this program in combination with

Compressed Music Enhancer for a clearer and more spatial sound field.

Sound programs suitable for music (MUSIC)

The following sound programs are optimized for listening to music sources.

Hall in Munich

This program simulates a Munich concert hall with approximately 2,500

seats that uses stylish wood for the interior finishing. Fine, beautiful

reverberations spread richly, creating a calming atmosphere. The

listener’s virtual seat is at the center left of the arena.

Hall in Vienna

This program simulates a 1700-seat, middle-sized concert hall with a

shoebox shape that is traditional in Vienna. Pillars and ornate carvings

create extremely complex reverberations from all around the audience,

producing a very full, rich sound.

Chamber

This program creates a relatively wide space with a high ceiling, like an

audience hall in a palace. It offers pleasant reverberations that are

suitable for courtly music and chamber music.

Cellar Club

This program simulates an intimate concert venue with a low ceiling and

homey atmosphere. A realistic, live sound field delivers powerful sounds

that make you feel as if you are sitting in the front row in front of a small

stage.

The Roxy Theatre

This program creates the sound field of a 460-seat rock music concert

venue in Los Angeles. The listener’s virtual seat is at the center left of the

hall.

The Bottom Line

This program creates the sound field at stage front in The Bottom Line, a

famous New York jazz club once. The floor can seat 300 people to the

left and right in a sound field offering real and vibrant sound.

Music Video

This program allows you to enjoy videos of pop, rock, and jazz concerts,

as if you were there yourself. Immerse yourself in the hot concert

atmosphere thanks to the vividness of the singers and solos on stage, a

presence sound field that emphasizes the beat of rhythm instruments,

and a surround sound field that reproduces the space of a big live hall.

Sound programs suitable for stereo playback (STEREO)

You can select stereo playback.

2ch Stereo

Use this program to mix down multichannel sources to 2 channels. When

multichannel signals are input, they are down mixed to 2 channels and

output from the front speakers (this program does not utilize CINEMA

DSP).

5ch Stereo

Use this program to output sound from all speakers. When you play back

multichannel sources, the unit mixes down the source to 2 channels, and

then outputs the sound from all speakers. This program creates a larger

sound field and is ideal for background music at parties.

Enjoying sound field effects without surround speakers

(Virtual CINEMA DSP)

If you select one of the sound programs (except 2ch Stereo and 5ch Stereo) when no

surround speakers are connected, the unit automatically creates the surround sound

field using the front-side speakers.

Enjoying surround sound with 5 speakers placed in

front (Virtual CINEMA FRONT)

You can enjoy the surround sound even when the surround speakers are placed in

front.

Enjoying surround sound with headphones (SILENT

CINEMA)

You can enjoy surround or sound field effects, like a multichannel speaker system, with

stereo headphones by connecting the headphones to the

PHONES jack and selecting

a sound program or a surround decoder.

Enjoying unprocessed playback

You can play back input sources without any sound field effect processing.

Playing back in original channels (straight decode)

When the straight decode mode is enabled, the unit produces stereo sound from the

front speakers for 2-channel sources such as CDs, and produces unprocessed

multichannel sounds for multichannel sources.

Press STRAIGHT.

Each time you press the key, the straight decode mode is enabled or

disabled.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

STRAIGHT

VOL.

Playing back 2-channel sources in multichannel

(surround decoder)

The surround decoder enables unprocessed multichannel playback from 2-channel

sources. When a multichannel source is input, it works the same way as the straight

decode mode.

For details on each decoder see “Glossary” (p.76).

Press PROGRAM repeatedly to select a surround decoder.

The previously selected surround decoder is selected. You can change

the surround decoder in “Sur.Decode

” (p.47) in the “Option” menu.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

PROG RAM

STRAIGHT

ENHANCER BASS

DVD

S C E NE

RADIO

SLEEP

IGHT

ENHANCER

S C E N

ADIO

SLEE

PROGRAM

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

†‡Pro Logic

VOL.

“SUR. DECODE” appears

bPro Logic

Uses the Dolby Pro Logic decoder suitable for all sources.

bPLII Movie

Uses the Dolby Pro Logic II decoder suitable for movies.

bPLII Music

Uses the Dolby Pro Logic II decoder suitable for music.

bPLII Game

Uses the Dolby Pro Logic II decoder suitable for games.

Neo:6 Cinema

Uses the DTS Neo: 6 decoder suitable for movies.

Neo:6 Music

Uses the DTS Neo: 6 decoder suitable for music.

Note

You can adjust the surround decoder parameters in “DSP Parameter” (p.59) in the “Setup” menu.

Enhancing the bass (Extra Bass)

Extra Bass allows you to enjoy enhanced bass sounds, regardless of the size of the

front speakers and the presence or absence of the subwoofer.

Press BASS.

Each time you press the key, Extra Bass is enabled or disabled.

Note

You can also use “Extra Bass” (p.55) in the “Setup” menu to enable/disable Extra Bass.

Playing back digitally compressed formats (such as

MP3, etc.) with enriched sound (Compressed Music

Enhancer)

Compressed Music Enhancer adds depth and breadth to the sound, allowing you to

enjoy a dynamic sound close to the original sound before it was compressed. This

function can be used along with any other sound modes.

Press ENHANCER.

Each time you press the key, Compressed Music Enhancer is enabled or

disabled.

MUTE

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Enhancer On

VOL.

ENHANCER

“ENHANCER” lights up

Note

▪ Compressed Music Enhancer does not work on the following audio sources.

– Signals whose sampling rate is over 48 kHz

– High-definition streaming audio

▪ You can also use “Enhancer (Enhancer)” (p.48) in the “Option” menu to enable/disable

Compressed Music Enhancer.

Listening to FM/AM radio

You can tune into a radio station by specifying its frequency or selecting from

registered radio stations.

Note

▪ The radio frequencies differ depending on the country or region where the unit is being used. The

explanation of this section uses a display with frequencies used in U.K. and Europe models.

▪ If you cannot obtain good reception on the radio, adjust the direction of the FM/AM antennas.

Setting the frequency steps

(Asia, Taiwan, Brazil and General models only)

At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz for AM.

Depending on your country or region, set the frequency steps to 100 kHz for FM and

10 kHz for AM.

Set the unit to standby mode.

When holding down STRAIGHT on the front panel, press z

(power).

(power)

STRAIGHTPROGRAM

Press PROGRAM repeatedly to select “TU”.

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

TU••••FM50/AM9

Press STRAIGHT to select “FM100/AM10”.

Press z (power) to set the unit to standby mode and turn it on

again.

Selecting a frequency for reception

Press FM/AM to select a band.

“TUNER” is selected as the input source and then the frequency currently

selected is displayed.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

FM 87.50MHz

VOL.

Press TUNING repeatedly to set a frequency.

Hold down the key for about a second to search stations automatically.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

TUNING

PRESET

TUNING

MEMORY

BLUE

YELLOWGREEN

RED

PRESET

MEMO

BLUE

YEL

GREEN

TUNING

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

FM 98.50MHz

VOL.

STEREO

TUNED

“TUNED” lights up when a signal is received from a radio station.

“STEREO” also lights up when a stereo signal is received.

Note

▪ You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio reception by

selecting “

FM Mode” (p.47) in the “Option” menu. When the signal reception for an FM radio

station is unstable, switching to monaural may improve it.

▪ You can watch videos input from external devices while listening to radio by selecting the video

input jack in

“Video Out (Video Out)” (p.50) in the “Option” menu.

Registering favorite radio stations (presets)

You can register up to 40 radio stations as presets. Once you have registered stations,

you can easily tune into them by selecting their preset numbers.

Registering radio stations automatically (Auto Preset)

Automatically register FM radio stations with strong signals (up to 40 stations).

Note

▪ To register AM radio stations, follow “Registering a radio station manually” (p.39).

▪ (U.K. and Europe models only)

Only Radio Data System broadcasting stations are registered automatically by the Auto Preset function.

Press FM/AM to select “TUNER” as the input source.

Press OPTION.

Use the cursor keys to select “Preset” and press ENTER.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Preset

VOL.

To start the Auto Preset process, press ENTER.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

01:FM 87.50MHz

VOL.

“SEARCH” appears during Auto Preset

Preset number from which to start the registration

Note

▪ To specify the preset number from which to start the registration, press cursor keys (e/r) or

PRESET to select a preset number.

▪ To cancel the Auto Preset process, press RETURN.

When the Auto Preset process finishes, “FINISH” appears and the “Option” menu

closes automatically.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Auto Preset

VOL.

Registering a radio station manually

Select a radio station manually and register it to a preset number.

Follow “Selecting a frequency for reception” (p.37) to tune into

the desired radio station.

Hold down MEMORY for a few seconds.

The first time that you do register a station, the selected radio station will

be registered to the preset number “01”. Thereafter, each radio station

you select will be registered to the next empty (unused) preset number

after the most recently registered number.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

TUNING

PRESET

TUNING

MEMORY

BLUE

YELLOWGREEN

RED

TUNING

PRESET

TUNING

BLUE

YEL

GREEN

MEMORY

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

01:FM 98.50MHz

STEREO

TUNED

VOL.

Preset number

Note

To specify the preset number for registering, press PRESET to select a preset number, and then

press MEMORY.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

02:Empty

STEREO

TUNED

VOL.

“Empty” (not in use) or the frequency currently registered

Selecting a preset station

Tune into a registered radio station by selecting its preset number.

Press FM/AM to select “TUNER” as the input source.

Press PRESET repeatedly to select the desired radio station.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

TUNING

PRESET

TUNING

MEMORY

BLUE

YELLOWGREEN

RED

TUNING

MEMO

BLUE

YEL

GREEN

PRESET

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

01:FM 98.50MHz

STEREO

TUNED

VOL.

Note

“No Presets” appears when no radio stations are registered.

Clearing preset stations

Clear radio stations registered to the preset numbers.

Press FM/AM to select “TUNER” as the input source.

Press OPTION.

Use the cursor keys to select “Preset” and press ENTER.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Preset

VOL.

Use the cursor keys (q/w) to select “CLEAR”.

Use the cursor keys (e/r) to select a preset station to be cleared

and press ENTER.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

01:FM 98.50MHz

STEREO

TUNED

VOL.

Preset station to be cleared

If the preset station is cleared, “Cleared” appears and then the next in-use

preset number is displayed.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

STEREO

TUNED

01:Cleared

VOL.

Repeat step 5 until all desired preset stations are cleared.

To exit from the menu, press OPTION.

Radio Data System tuning

(U.K. and Europe models only)

Radio Data System is a data transmission system used by FM stations in many

countries. The unit can receive various types of Radio Data System data, such as

“Program Service”, “Program Type”, “Radio Text

” and “Clock Time”, when it is tuned

into a Radio Data System broadcasting station.

Displaying the Radio Data System information

Tune into the desired Radio Data System broadcasting station.

Note

We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations

(p.38).

Press INFO.

Each time you press the key, the displayed item changes.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

Program Type

STEREO

TUNED

VOL.

Item name

About 3 seconds later, the corresponding information for the displayed

item appears.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

CLASSICS

STEREO

TUNED

VOL.

Information

Program Service

Program service name

Program Type

Current program type

Radio Text

Information on the current program

Clock Time

Current time

DSP Program

Sound mode name

Audio Decoder

Decoder name

Frequency

Note

“Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio

station does not provide the Radio Data System service.

Receiving traffic information automatically

When “TUNER” is selected as the input source, the unit automatically receives traffic

information. To enable this function, follow the procedure below to set the traffic

information station.

When “TUNER” is selected as the input source, press OPTION.

Use the cursor keys to select “Traffic Program” (TrafficProgram)

and press ENTER.

The traffic information station search will start in 5 seconds. Press ENTER

again to start the search immediately.

Note

▪ To search upward/downward from the current frequency, press the cursor keys (q/w) while

“READY” is displayed.

▪ To cancel the search, press RETURN.

▪ Texts in parentheses denote indicators on the front display.

The following screen appears for about 3 seconds when the search

finishes.

MUTE

ENHANCER

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

TP FM101.30MHz

VOL.

STEREO

TUNED

Traffic information station (frequency)

Note

“TP Not Found” appears for about 3 seconds when no traffic information stations are found.

Playing back music stored on a Bluetooth® device

You can play back music files stored on a Bluetooth device on the unit.

Please also refer to the owner’s manual of your Bluetooth device.

Note

▪ The Bluetooth device must support A2DP.

▪ You cannot play back video files stored on a Bluetooth device on the unit.

Connecting a Bluetooth® device (pairing)

When connecting a Bluetooth device to the unit for the first time, the pairing operation

is required to perform. Pairing is an operation that registers the Bluetooth devices with

each other beforehand. Once pairing has been completed, subsequent reconnection

will be easy even after the Bluetooth connection is disconnected.

Press BLUETOOTH to select “Bluetooth” as the input source.

Hold down MEMORY on the front panel or the remote control for

more than 3 seconds.

“Searching…” appears on the front display.

Note

▪ You can also use the “Option” menu to pair a Bluetooth device. Press OPTION, and then use the

cursor keys to select “Pairing

”.

▪ If another Bluetooth device is already connected, disconnect the Bluetooth connection before

you perform a pairing operation.

▪ To cancel pairing, press MEMORY.

Turn on the Bluetooth function on your device.

From the Bluetooth device list on your device, select “*******

Yamaha” (*******: model name of the unit).

After pairing has been completed and the unit is connected to the

Bluetooth device, “

Connected” appears on the front display. While a

Bluetooth connection is established, the Bluetooth indicators light up.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

VOL.

L C R

SL SW SR

VOL.

Connected

OUT

Note

▪ If you are prompted to input a passkey during a pairing procedure, input the numerals “0000”.

▪ Complete a pairing procedure within 30 seconds.

▪ If no Bluetooth devices are found, “Not found” appears.

Playback of Bluetooth® device contents

Connect a paired Bluetooth device and start playback. Check the following

beforehand:

• Pairing has been completed.

• Bluetooth function on the Bluetooth device is turned on.

Operate the Bluetooth device to establish a Bluetooth connection.

Select the model name of the unit from the Bluetooth device list on your

device.

When a connection is established, the unit’s input source automatically

switches to “

Bluetooth”.

Note

▪ If you do not want the input source to switch automatically when a connection is established, set

“Input Interlock” (

p.47) to “Off” in the “Option” menu.

▪ You can operate the unit to search and connect the Bluetooth device (only the most recently

connected device). In that case, follow one of the procedures below.

– Switch the input source to “Bluetooth”.

– Press ENTER while the input source is “Bluetooth”. Otherwise, press OPTION and use the

cursor keys to select “Connect”.

▪ If you cannot connect the device, please perform pairing again.

Operate the Bluetooth device to play back music.

Note

You cannot operate the unit to select or play back music, or display informations such as song

names.

Disconnecting a Bluetooth® connection

Follow one of the procedures below to disconnect a Bluetooth connection.

• Perform the disconnect operation on the Bluetooth device.

• Press ENTER.

• Press OPTION and use the cursor keys to select “Disconnect”.

• Switch the unit's input source to other than “Bluetooth”.

Playing back music stored on a USB storage device (Except for USA, Canada, Australia models)

You can play back music files stored on a USB storage device on the unit.

Note

For details on playable USB devices, see “Supported devices and file formats” (p.78).

Connecting a USB storage device

Connect the USB storage device to the USB jack.

AUX

STRAIGHT

RADIO

AUDIO

USB

The unit (front)

USB storage device

Note

▪ If the USB storage device contains many files, it may take time to load them. In this case, “Loading…”

appears in the front display.

▪ Stop playback of the USB storage device before disconnect it from the USB jack.

▪ Connect a USB storage device directly to the USB jack of the unit. Do not use extension cables.

Playback of USB storage device contents

Follow the procedure below to operate the USB storage device contents and start

playback.

You can control the USB memory device with the menu displayed on the TV screen.

Note

▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI.

▪ “_” (underscore) will be displayed for characters not supported by the unit.

Press USB to select “USB” as the input source.

The browse screen (p.45) is displayed on the TV.

Note

If playback is ongoing on your USB storage device, the playback screen is displayed.

Use the cursor keys to select an item and press ENTER.

If a song is selected, playback starts and the playback screen (p.45) is

displayed.

Note

▪ To return to the previous screen, press RETURN.

▪ To switch the screen mode browse/playback/off, press DISPLAY.

▪ Files not supported by the unit cannot be selected.

Browse screen

USB - Top

Blues

Classical

Electronica

Jazz

Pop

Rock

Soundtrack

Speaking

1/9999

List name

Contents list

Displays the list of USB storage device contents. Use the cursor keys to select an

item and press ENTER to confirm the selection.

Item number/total

Status indicators

Display the current repeat/random settings (p.46) and playback status (such as

play/pause).

Operation menu

Press the cursor key (r) and then use the cursor keys (q/w) to select an item.

Press ENTER to confirm the selection.

Icon Function

Moves 10 pages backward.

Moves to the previous page of the list.

Moves to the next page of the list.

Moves 10 pages forward.

Moves to the playback screen.

Note

A content selected by the cursor is displayed on the front display.

Playback screen

USB

Song

2 : 30 5 : 30

Album

Artist

Status indicators

Display the current repeat/random settings (p.46) and playback status (such as

play/pause).

Playback information

Displays the artist name, album name, song title, and elapsed time.

Use the following remote control keys to control playback.

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

TUNING

PRESET

TUNING

MEMORY

BLUE

YELLOWGREEN

RED

PRESET

BLUE

YEL

GREEN

External device operation

keys

External device

operation keys

Function

Resumes playback from pause or starts playback of the previously

selected song.

Stops playback.

Stops playback temporarily.

Skips forward/backward.

Searches forward/backward (by holding down).

Note

A content name of a current playback is displayed on the front display. To switch the displayed item, press

INFO (p.30).

Repeat/random settings

You can configure the repeat/random settings for playback of USB storage device

contents.

When “USB” is selected as the input source, press OPTION.

Use the cursor keys to select “Repeat” (Repeat) and press

ENTER.

Note

▪ To return to the previous screen during menu operations, press RETURN.

▪ Texts in parentheses denote indicators on the front display.

Use the cursor keys (e/r) to select a setting.

Setting Function

Off (Off) Turns off the repeat function.

One (One)

Plays back the current song repeatedly. “c” appears

on the TV screen.

All (All)

Plays back all songs in the current album (folder)

repeatedly.

“v” appears on the TV screen.

Random (Random)

Plays back songs in random order.

“x” appears on the TV screen.

To exit from the menu, press OPTION.

Configuring playback settings for different playback sources (Option menu)

You can configure separate playback settings for different playback sources. This

menu is available on the front panel (or on the TV screen), allowing you to easily

configure settings during playback.

Press OPTION.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

VOL.

Input Select

Front display

Option

Input Select

Tone Control

DSP/Surround

Volume Trim

Lipsync

Signal Info.

Audio In

Back

RETURN

TV screen

Use the cursor keys to select an item and press ENTER.

Note

To return to the previous screen during menu operations, press RETURN.

Use the cursor keys (e/r) to select a setting.

To exit from the menu, press OPTION.

Option menu items

Note

▪ Available items vary depending on the selected input source.

▪ Text in parentheses denotes indicators on the front display.

▪ Default settings are underlined.

Item Function Page

Input Select (Input Select)

Switches the input source. p.48

Tone Control (

Tone Control)

Adjusts the level of high-frequency range and low-

frequency range individually.

p.48

DSP/Surround

(DSP/

Surround)

Program (PRG)

Select the sound programs and stereo playback. p.33

Sur.Decode

(SrDec)

Select which surround decoder is used when

Sur.Decode

is selected as the program.

p.35

DSP Level

(DSP Level)

Adjusts the sound field effect level. p.48

Adaptive DRC

(A.DRC)

Sets whether the dynamic range (from maximum to

minimum) is automatically adjusted when the volume

is adjusted.

p.48

Enhancer

(Enhancer)

Enables/disables Compressed Music Enhancer. p.48

Volume Trim

(Volume Trim)

Input Trim

(In.Trim)

Corrects volume differences between input sources. p.49

Subwoofer Trim

(SW.Trim)

Fine-adjusts the subwoofer volume. p.49

Lipsync (Lipsync)

Enables/disables the “Lipsync” setting in the “Setup”

menu.

p.49

Signal Info. (Signal Info.)

Displays information about the video/audio signal. p.49

Audio In (Audio In)

Combines the video jack of the selected input source

with an audio jack of others.

p.49

Video Out (Video Out)

Selects a video to be output with radio sounds. p.50

FM Mode (FM Mode)

Switches between “Stereo” and “Mono” for FM radio

reception.

p.37

Preset (Preset)

Auto Preset

Automatically registers FM radio stations with strong

signals as presets.

p.38

Clear Preset

Clear radio stations registered to preset numbers. p.40

Traffic Program

(TrafficProgram)

(U.K. and Europe models only)

Automatically searches for a traffic information

station.

p.41

Item Function Page

Repeat

(Repeat)

(Except for USA, Canada, Australia models)

Configures the repeat setting for the USB storage

device.

p.46

Pairing

(Pairing)

Performs a pairing operation between the unit and

your Bluetooth device.

p.42

Connect/Disconnect (Connect/

Disconnect)

Connects/disconnects the Bluetooth device. p.43

Input Interlock (Interlock)

Sets whether the input source automatically switches

to "Bluetooth" when a Bluetooth connection is

established.

p.43

Input Select (Input Select)

Switches the input source. Press ENTER to switch to the selected input source.

Choices

HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX

Tone Control (Tone Control)

Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass)

individually.

Choices

Treble (Treble), Bass (Bass)

Setting range

-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)

Note

▪ When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears.

▪ You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or

“Bass”, then press PROGRAM to make an adjustment.

▪ If you set an extreme value, sounds may not match those from other channels.

DSP/Surround (DSP/Surround)

Configures the sound field program and surround settings.

DSP Level (DSP Level)

Adjusts the sound field effect level.

Setting range

-6 dB to

0 dB to +3 dB (1 dB increments)

Adaptive DRC (A.DRC)

Sets whether the dynamic range (from maximum to minimum) is automatically

adjusted when the volume level is adjusted. When it is set to “On”, it is useful for

listening to playback at a low volume at night.

Settings

On (On) Automatically adjusts the dynamic range.

Off (Off) The dynamic range is not automatically adjusted.

If “On” is selected, the dynamic range becomes narrow at a low volume and wide

at a high volume.

Enhancer (Enhancer)

Enables/disables Compressed Music Enhancer (p.36).

Note

▪ This setting is applied separately to each input source.

▪ You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer

(p.36).

Settings

Off (Off) Disables Compressed Music Enhancer.

On (On) Enables Compressed Music Enhancer.

Default

Bluetooth, USB, TUNER: On (On)

Others: Off (Off)

Volume Trim (Volume Trim)

Fine-adjusts volume difference between input sources or subwoofer volume.

Input Trim (In.Trim)

Corrects volume differences between input sources. If you are bothered by volume

differences when switching between input sources, use this function to correct it.

Note

This setting is applied separately to each input source.

Setting range

-6.0 dB to

0.0 dB to +6.0 dB (0.5 dB increments)

Subwoofer Trim (SW.Trim)

Fine-adjusts the subwoofer volume.

Setting range

-6.0 dB to

0.0 dB to +6.0 dB (0.5 dB increments)

Lipsync (Lipsync)

Enables/disables the adjustment configured in “Lipsync” (p.59) in the “Setup” menu.

Note

This setting is applied separately to each input source.

Settings

Off (Off) Disables the “Lipsync” adjustment.

On (On) Enables the “Lipsync” adjustment.

Signal Info. (Signal Info.)

Displays information about the video/audio signal.

Choices

Format (FORMAT) Audio format of the input signal

Channel (CHANNEL)

The number of source channels in the input signal (front/surround/LFE)

For example, “3/2/0.1” means 3 front channels, 2 surround channels, and

LFE.

Sampling (SAMPLING) The number of samples per second of the input digital signal

Bitrate (BITRATE) The amount of data per second of the input bitstream signal

Video In (VIDEO IN) Type and resolution of the input digital signal

Video Out

(VIDEO OUT

)

Type and resolution of the output digital signal

Note

To switch the information on the front display, press the cursor keys (q/w) repeatedly.

Audio In (Audio In)

Combines the video jack of the selected input source with an audio jack of others. For

example, use this function in the following cases.

• Connecting a playback device that supports HDMI video output, but not HDMI

audio output

Input sources

HDMI 1-4, AUDIO 1-2, AV 1-3

Setup procedure

See “Changing the combination of video/audio input jacks” (p.21).

Video Out (Video Out)

Selects a video to be output with the selected audio source. For example, you can

watch the video while listening to the radio.

Input sources

AUDIO, TUNER, USB, Bluetooth, AUX

Settings

Off (Off) Does not output video.

HDMI 1-4, AV 1-3 Outputs video input through the corresponding video input jacks.

CONFIGURATIONS

Configuring various functions (Setup Menu)

You can configure the unit’s various function with the menu displayed on the TV

screen.

Note

Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out

operations while viewing the front display.

Press SETUP.

Use the cursor keys to select a menu and press ENTER.

Setup

Speaker

HDMI

Sound

ECO

Function

Language

Back

RETURN

Use the cursor keys to select an item and press ENTER.

Speaker

Conﬁguration

Level

Equalizer

Test Tone

Note

To return to the previous screen during menu operations, press RETURN.

Use the cursor keys (e/r) to select a setting and press ENTER.

To exit from the menu, press SETUP.

Setup menu items

Menu Item Function Page

Speaker

Configuration

Subwoofer

Selects whether or not a subwoofer is connected. p.54

Front

Selects the size of the front speakers. p.54

Center

Selects whether or not a center speaker is connected and its size. p.54

Surround

Selects whether or not surround speakers are connected and their size. p.55

Crossover

Sets the lower limit of the low-frequency component that can be output from speakers whose size is set to “Small”. p.55

Subwoofer Phase

Sets the phase of the subwoofer. p.55

Extra Bass

Enables/disables Extra Bass. p.55

Virtual CINEMA FRONT

Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. p.55

Distance

Sets the distance between each speaker and listening position. p.55

Level

Adjusts the volume of each speaker. p.56

Equalizer

Adjusts the tone with an equalizer. p.56

Test Tone

Enables/disables the test tone output. p.56

HDMI

HDMI Control

Enables/disables HDMI Control. p.57

Audio Output

Selects a device to output audio. p.57

TV Audio Input

Selects an audio input jack of the unit to be used for TV audio input. p.57

Standby Sync

Selects whether to use HDMI control to link the standby behavior of the TV and the unit. p.58

ARC

Enables/disables ARC. p.58

SCENE

Enables/disables SCENE link playback. p.58

Sound

DSP Parameter

Panorama

Enables/disables the broadening effect of the front sound field. p.59

Center Width

Adjusts the broadening effect of the center sound field. p.59

Dimension

Adjusts the difference in level between the front and surround sound fields. p.59

Center Image

Adjusts the center orientation level (broadening effect) of the front sound field. p.59

Lipsync

Select

Selects the method to adjust the delay between video and audio output. p.59

Adjustment

Adjusts the delay between video and audio output manually. p.60

Dialogue Dialogue Level

Adjusts the volume of dialogue sounds. p.60

Volume

Scale

Switches the scale of the volume display. p.60

Dynamic Range

Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. p.60

Max Volume

Sets the limit value of the volume. p.60

Initial Volume

Sets the initial volume for when this receiver is turned on. p.60

Menu Item Function Page

ECO

Auto Power Standby

Set the amount of time for the auto-standby function. p.61

ECO Mode

Enables/disables the eco mode (power saving mode). p.61

Function

Input Rename

Changes the input source name displayed on the front display. p.62

Input Skip

Set which input source is skipped when operating the INPUT key. p.63

Dimmer

Adjusts the brightness of the front display. p.63

Memory Guard

Prevents accidental changes to the settings. p.63

Remote Color Key

Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. p.64

Language

Select an on-screen menu language. p.64

Speaker

Configures the speaker settings manually.

Note

Default settings are underlined.

Configuration

Configures the output characteristics of the speakers.

Note

When you configure the speaker size, select “Large” if the woofer diameter of your speaker is 16 cm (6‑1/4”)

or larger or “Small

” if it is smaller than 16 cm (6‑1/4”).

Subwoofer

Selects whether or not a subwoofer is connected.

Settings

Use

Select this option when a subwoofer is connected.

The subwoofer will produce LFE (low-frequency effect) channel audio

and low-frequency components from other channels.

None

Select this option when no subwoofer is connected.

The front speakers will produce LFE (low-frequency effect) channel

audio and low-frequency components from other channels.

Front

Selects the size of the front speakers.

Settings

Small

Select this option for small speakers.

The subwoofer will produce front channel low-frequency components

(configurable in “

Crossover”).

Large

Select this option for large speakers.

The front speakers will produce all of the front channel frequency

components.

Note

“Front” is automatically set to “Large” when “Subwoofer” is set to “None”.

Center

Selects whether or not a center speaker is connected and its size.

Settings

Small

Select this option for small speakers.

The subwoofer or front speakers will produce center channel low-

frequency components (configurable in “

Crossover”).

Large

Select this option for large speakers.

The center speaker will produce all of the center channel frequency

components.

None

Select this option when no center speaker is connected.

The front speakers will produce center channel audio.

Surround

Selects whether or not surround speakers are connected and their sizes.

Settings

Small

Select this option for small speakers.

The subwoofer or front speakers will produce surround channel low-

frequency components (configurable in “

Crossover”).

Large

Select this option for large speakers.

The surround speakers will produce all of the surround channel

frequency components.

None

Select this option when no surround speakers are connected.

The front speakers will produce surround channel audio. Virtual

CINEMA DSP works when you select a sound program.

Crossover

Sets the lower limit of the low-frequency components that can be output from a

speaker whose size is set to “

Small”. A frequency sound lower than the specified

value will be produced from the subwoofer or front speakers.

Settings

40 Hz, 60 Hz,

80 Hz, 90 Hz, 100 Hz, 110 Hz, 120 Hz, 160 Hz, 200 Hz

Note

If the volume and crossover frequency are adjustable on your subwoofer, set the volume to half and

crossover frequency to maximum.

Subwoofer Phase

Sets the phase of the subwoofer. When the bass sound is lacking or unclear,

switch the subwoofer phase.

Settings

Normal Does not reverse the subwoofer phase.

Reverse Reverses the subwoofer phase.

Extra Bass

Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy

enhanced bass sounds, regardless of the size of the front speakers and the

presence or absence of the subwoofer.

Settings

Off Disables Extra Bass.

On Enables Extra Bass.

Note

You can also use BASS on the remote control to enable/disable Extra Bass (p.36).

Virtual CINEMA FRONT

Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT)

configuration.

Settings

Off Disables the front 5-channel speaker configuration.

On Enables the front 5-channel speaker configuration.

Note

▪ Select “On” only when utilizing the Virtual CINEMA FRONT configuration (p.13).

▪ This setting is not available when “Surround” is set to “None”.

Distance

Sets the distance between each speaker and listening position so that sounds from the

speakers reach the listening position at the same time. First, select the unit of distance

from “Meter” or “Feet”.

Choices

Front L, Front R, Center, Surround L, Surround R, Subwoofer

Setting range

0.30 m to 24.00 m (1.0 ft to 80.0 ft), 0.05 m (0.2 ft) increments

Default

Front L, Front R, Subwoofer: 3.00 m (10.0 ft)

Center: 2.60 m (8.6 ft)

Others: 2.40 m (8.0 ft)

Level

Adjusts the volume of each speaker.

Choices

Front L, Front R, Center, Surround L, Surround R, Subwoofer

Setting range

-10.0 dB to +10.0 dB (0.5 dB increments)

Default

Front L, Front R, Subwoofer: 0.0 dB

Others: -1.0 dB

Equalizer

Adjusts the tone with an equalizer.

EQ Select

Selects the type of equalizer to be used.

Settings

PEQ

Applies the parametric equalizer values obtained by the YPAO

measurement (

p.25).

GEQ

Select this option when you want to adjust the equalizer manually.

For details, see “Manual equalizer adjustment”.

Off Does not use the equalizer.

Note

“PEQ” is available only when the YPAO has been performed (p.25).

Manual equalizer adjustment

Set “EQ Select” to “GEQ”.

Use the cursor keys (q/w) to select “Channel” and the cursor

keys (e/r) to select the desired speaker channel.

Use the cursor keys (q/w) to select the desired band

(frequency) and the cursor keys (e/r) to adjust the gain.

Setting range

-6.0 dB to +6.0 dB

To exit from the menu, press SETUP.

Test Tone

Enables/disables the test tone output. Test tone output helps you to adjust the speaker

balance or equalizer while confirming its effect.

Settings

Off Does not output test tones.

Outputs test tones automatically when you adjust the speaker balance or

equalizer.

HDMI

Configures the HDMI settings.

Note

Default settings are underlined.

HDMI Control

Enables/disables HDMI Control (p.79).

Settings

Off Disables HDMI Control.

Enables HDMI Control.

Configure the settings in “TV Audio Input”, “Standby Sync”, “ARC”, and

“SCENE”.

Note

To use HDMI control, you need to perform the HDMI Control link setup (p.79) after connecting HDMI

Control-compatible devices.

Audio Output

Selects a device to output audio.

Note

This setting is available only when “HDMI Control” is set to “Off”.

Amp

Enables/disables the audio output from the speakers connected to the unit.

Settings

Off Disables the audio output from the speakers.

On Enables the audio output from the speakers.

HDMI OUT (TV)

Enables/disables the audio output from a TV connected to the HDMI OUT jack.

Settings

Off Disables the audio output from the TV.

On Enables the audio output from the TV.

TV Audio Input

Selects an audio input jack of the unit to be used for TV audio input when “HDMI

Control” is set to “On”. The unit’s input source automatically switches to TV audio when

the TV input is switched to its built-in tuner.

Settings

AV 1–3, AUDIO 1–2

Default

AV 2

Note

When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an

external device because the input will be used for TV audio input.

Standby Sync

Select whether to use HDMI control to link the standby behavior of the TV and the unit

when “HDMI Control

” is set to “On”.

Settings

Off Does not set the unit to standby mode when the TV is turned off.

On Sets the unit to standby mode when the TV is turned off.

Auto

Sets the unit to standby mode when the TV is turned off only when the unit

is receiving TV audio or HDMI signals.

ARC

Enables/disables ARC (p.19) when “HDMI Control” is set to “On”.

Settings

Off Disables ARC.

On Enables ARC.

Note

You do not need to change this setting normally. In case noises are produced from the speakers connected

to the unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off”

and use the TV’s speakers.

SCENE

Enables/disable SCENE link playback when “HDMI Control” is set to “On”.

When SCENE link playback is enabled, HDMI Control-compatible devices connected

to the unit via HDMI automatically works as follows, with a scene selection.

• TV: turning on and displaying video from the playback device

• Playback device: starting playback

Choices (SCENE keys)

BD / DVD, TV, CD, RADIO

Settings

Off Disables SCENE link playback for the selected SCENE key.

On Enables SCENE link playback for the selected SCENE key.

Default

BD / DVD, TV: On

CD, RADIO: Off

Note

SCENE link playback may not work properly due to the compatibility between devices. We recommend using

TV and playback devices from the same manufacturer so that HDMI Control works more effectively.

Sound

Configures the audio output settings.

Note

Default settings are underlined.

DSP Parameter

Configures the surround decoder settings.

Panorama

Enables/disables the broadening effect of the front sound field. When this function

is enabled, you can wrap front left/right channel sounds around the field and

generate a spacious sound field in combination with the surround sound field. This

setting is effective when “bPLII Music” is selected.

Settings

Off Disables the broadening effect of the front sound field.

On Enables the broadening effect of the front sound field.

Center Width

Adjusts the broadening effect of the center sound field. Higher to enhance the

broadening effect, and lower to reduce it (closer to center). This setting is effective

when “bPLII Music” is selected.

Setting range

0 to 3 to 7

Dimension

Adjusts the difference in level between the front and surround sound fields. Higher

to strengthen the front sound field and lower to strengthen the surround sound

field. This setting is effective when “bPLII Music” is selected.

Setting range

-3 to 0 to +3

Center Image

Adjusts the center orientation level (broadening effect) of the front sound field.

Higher to strengthen the center orientation level (less broadening effect) and lower

to weaken (more broadening effect). This setting is effective when “

Neo:6 Music”

is selected.

Setting range

0.0 to

0.3 to 1.0

Lipsync

Adjusts the delay between video and audio output.

Note

You can enable/disable the Lipsync function by input sources in “Lipsync (Lipsync)” (p.49) in the “Option”

menu.

Select

Selects the method to adjust the delay between video and audio output.

Setting range

Manual

Select this option when you want to adjust the delay between video

and audio output manually.

Adjust the audio output timing in “Adjustment”.

Auto

Adjusts the delay between video and audio output automatically when

a TV that supports an automatic lipsync function is connected to the

unit via HDMI.

If necessary, you can fine-adjust the audio output timing in

“Adjustment”.

Note

“Select” is automatically set to “Manual” depending on the TV connected to the unit.

Adjustment

Adjusts the delay between video and audio output manually when “Select” is set to

“Manual

”. You can fine-adjust the audio output timing when “Select” is set to

“Auto”.

Setting range

0 ms to 500 ms (1 ms increments)

Dialogue

Adjusts the volume of dialogue sounds.

Dialogue Level

Adjusts the volume of the center orientation sounds such as dialogue.

Setting range

0 to 3 (higher to strengthen)

Volume

Configures the volume settings.

Scale

Switches the scale of the volume display.

Settings

dB Displays the volume in the “dB” unit.

0-97 Displays the volume in the numeric value (0.5 to 97.0).

Dynamic Range

Selects the dynamic range adjustment method for bitstream audio (Dolby Digital

and DTS signals) playback.

Settings

Maximum Produces audio without adjusting the dynamic range.

Standard Optimizes the dynamic range for regular home use.

Min/Auto

Sets the dynamic range for clear sound even at night or at low

volumes.

When playing back Dolby TrueHD signals, the dynamic range is

automatically adjusted based on the input signal information.

Max Volume

Sets the limit value of the volume.

Setting range

-30.0 dB to +15.0 dB (5.0 dB increments),

+16.5 dB [50.0 to 95.0 (5.0 increments),

97.0]

Initial Volume

Sets the initial volume when the receiver is turned on.

Settings

Off

Sets the level to the volume level of the unit when it last entered

standby mode.

Mute Sets the unit to mute the audio output.

-80.0 dB to +16.5 dB

(0.5 dB increments)

[0.5 to 97.0

(0.5 increments)]

Sets the level to the specified volume level.

ECO

Configures the power supply settings.

Note

Default settings are underlined.

Auto Power Standby

Set the amount of time for the auto-standby function.

Settings

Off Does not set the unit to standby mode automatically.

20 minutes

Sets the unit to standby mode when you have not operated the unit and

the unit has not detected any input signal for the specified time.

2 hours, 4 hours,

8 hours, 12 hours

Sets the unit to standby mode when you have not operated the unit for the

specified time.

Default

U.K. and Europe models: 20 minutes

Other models: Off

Note

Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front

display.

ECO Mode

You can reduce the unit’s power consumption by setting the eco mode to “On”. After

setting, be sure to press ENTER to restart the unit.

When the eco mode is enabled, you can reduce the unit’s power consumption.

Settings

Off Disables the eco mode.

On Enables the eco mode.

Note

▪ When “ECO Mode” is set to “On”, the front panel display may become dark.

▪ If you want to play audio at high volume, set “ECO Mode” to “Off”.

Function

Configures the functions that make the unit easier to use.

Note

Default settings are underlined.

Input Rename

Changes the input source name displayed on the front display. You can also select a

name from the presets or a name created by the Auto Rename function.

Input sources

HDMI 1-4, AUDIO 1-2, AV 1-3, USB, Bluetooth, AUX

Default

HDMI 1-4: Auto

Others: Manual (For USB, Bluetooth, AUX only “Manual” can be selected.)

Procedure to rename automatically

Use the cursor keys (q/w) to select an input source to be

renamed.

Use the cursor keys (e/r) to select “Auto”.

The unit creates a name automatically according to the connected

device.

To check a created name, press ENTER.

Note

During selecting “Auto”, the created name is saved even after the device connection is

terminated. To reset to the default setting, switch the setting to “

Manual” at once and then set

it again to “Auto”.

To change another input source name, repeat steps 1 to 3.

To exit from the menu, press SETUP.

Procedure to rename manually

Use the cursor keys (q/w) to select an input source to be

renamed.

Use the cursor keys (e/r) to select “Manual” and press

ENTER.

Note

To select the preset name, use the cursor keys (e/r).

Press ENTER.

The edit screen is displayed.

Use the cursor keys and ENTER key to edit the name, and then

select “OK” to confirm the new name.

Note

To cancel the entry, select “CANCEL”.

To change another input source name, repeat steps 1 to 4.

To exit from the menu, press SETUP.

Input Skip

Set which input source is skipped when operating the INPUT key.

You can select the desired input source quickly by using this function.

Input sources

HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX

Settings

Off Does not skip the selected input source.

On Skips the selected input source.

Dimmer

Adjusts the brightness of the front display.

Setting range

-4 to 0 (higher to brighten)

Note

The front display may become dark when “ECO Mode” (p.61) is set to “On”.

Memory Guard

Prevents accidental changes to the settings.

Settings

Off Does not protect the settings.

On Protects the settings until “Off” is selected.

Note

When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen.

Remote Color Key

Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control.

Settings

Default

Assigns the functions of playback devices connected to the unit with an

HDMI cable.

Input

Assigns the unit's input sources to each key. The assigned input sources

can be set separately.

Input sources

HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX

Default

RED: HDMI2, GREEN: HDMI4, YELLOW: AV 2, BLUE: AUX

Program

Assigns the functions of sound mode to each key.

RED: MOVIE

GREEN: MUSIC

YELLOW: STEREO

BLUE: SUR.DECODE

For example, if you press the RED key repeatedly, you can select your

favorite sound program from the sound programs (MOVIE

) (p.33) suitable

for the video source.

Language

Select an on-screen menu language.

Note

Default settings are underlined.

Settings

English English

日本語 Japanese

Français French

Deutsch German

Español Spanish

Русский Russian

Italiano Italian

中文 Chinese

Note

The information on the front display is provided in English only.

Configuring the system settings (ADVANCED SETUP menu)

Configure the system settings of the unit while viewing the front display.

Set the unit to standby mode.

While holding down STRAIGHT on the front panel, press

z (power).

(power)

STRAIGHTPROGRAM

Press PROGRAM to select an item.

Press STRAIGHT to select a setting.

Press z (power) to set the unit to standby mode and turn it on

again.

The new settings take effect.

ADVANCED SETUP menu items

Note

Default settings are underlined.

Item Function Page

SP IMP.

(U.S.A. and Canada models only)

Changes the speaker impedance setting.

p.65

REMOTE ID Selects the unit’s remote control ID. p.66

(Asia, Taiwan and General models only)

Changes the FM/AM tuning frequency setting.

p.66

TV FORMAT Switches the video signal type of HDMI output. p.66

4K MODE Selects the HDMI 4K signal format. p.66

INIT Restores the default settings. p.67

UPDATE Updates the firmware. p.67

VERSION Checks the version of firmware currently installed on the unit. p.67

Changing the speaker impedance setting (SP IMP.)

(U.S.A. and Canada models only)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

SP IMP.••8¬MIN

Change the unit’s speaker impedance settings depending on the impedance of the

speakers connected.

Settings

6 Ω MIN Select this option when you connect 6-ohm speakers to the unit.

8 Ω MIN Select this option when you connect 8-ohm or higher speakers to the unit.

Selecting the remote control ID (REMOTE ID)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

REMOTE ID••ID1

Change the unit’s remote control ID so that it matches the remote control’s ID (default:

ID1). When using multiple Yamaha AV receivers, you can set each remote control with

a unique remote control ID for its corresponding receiver.

Settings

ID1, ID2

Changing the remote control ID of the remote control

To select ID1, while holding down the cursor key (e), hold down

SCENE (BD/DVD) for more than 3 seconds.

To select ID2, while holding down the cursor key (e), hold down

SCENE (TV) for more than 3 seconds.

Changing the FM/AM tuning frequency setting (TU)

(Asia, Taiwan and General models only)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

TU••••FM50/AM9

Change the FM/AM tuning frequency setting of the unit depending on your country or

region.

Settings

FM100/AM10

Select this when you want to adjust the FM frequency by 100-kHz steps

and AM by 10-kHz steps.

FM50/AM9

Select this when you want to adjust the FM frequency by 50-kHz steps

and AM by 9-kHz steps.

Switching the video signal type (TV FORMAT)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

TV FORMAT•NTSC

Switch the video signal type of HDMI output so that it matches to the format of your TV.

Since the unit automatically selects the video signal type so that it matches to the TV, it

is unnecessary to change the setting normally. Change the setting only when images

on the TV screen do not appear correctly.

Settings

NTSC, PAL

Default

U.S.A., Canada, Korea, Taiwan and General models: NTSC

Other models: PAL

Selecting the HDMI 4K signal format (4K MODE)

4K MODE•MODE 2

Selects the format of signals input/output at the unit when HDMI 4K (60 Hz/50 Hz)

compatible TV and playback device are connected to the unit.

Settings

MODE 1

Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:4:4, 4:2:2 or 4:2:0 format.

Depending on the connected device or HDMI cables, video may not be

displayed correctly. In this case, select “MODE 2”.

MODE 2 Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:2:0 format.

Note

When “MODE 1” is selected, use a high-speed HDMI cable that supports 18 Gbps.

Restoring the default settings (INIT)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

INIT••••CANCEL

Restores the default settings for the unit.

Choices

ALL Restores the default settings for the unit.

CANCEL Does not perform an initialization.

Updating the firmware (UPDATE) (Except for USA,

Canada, Australia models)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

UPDATE•••••USB

New firmware that provides additional features or product improvements will be

released as needed. Updates can be downloaded from our website. For details, refer

to the information supplied with updates.

Firmware update procedure

Do not perform this procedure unless firmware update is necessary. Also, make sure

you read the information supplied with updates before updating the firmware.

Save the downloaded firmware to the root folder of a USB memory

device.

Press PROGRAM on the front panel to select “UPDATE”.

Connect the USB memory device to the USB jack.

To start firmware update, press INFO on the front panel.

Checking the firmware version (VERSION)

VOL.

MUTE

ENHANCER

STEREO

TUNED

SLEEP

OUT

ECO

CHARGE

ADAPTIVE DRC

VIRTUAL

VERSION••xx.xx

Check the version of firmware currently installed on the unit.

Note

It may take a while until the firmware version is displayed.

APPENDIX

Frequently asked questions

The frequently asked questions from customers and the answers are shown below.

The new speaker system does not provide an ideal sound balance...

If you have changed speakers or have a new speaker system, use YPAO to optimize

the speaker settings again (p.25). If you want to adjust the speaker settings manually,

use “Speaker” in the “Setup” menu (

p.54).

We want to set limitations on the volume control...

If someone accidentally operates the controls on the main unit or remote control, the

volume may suddenly increase. This may also cause injury or damage the unit or

speakers. We recommend using “

Max Volume” in the “Setup” menu to set the

maximum volume level for the unit in advance (p.60).

I want to fix the volume when turning on the unit...

By default, the volume level when the unit last entered standby mode is automatically

applied. If you want to fix the volume, use “

Initial Volume” in the “Setup” menu to set

the volume to be applied when the receiver is turned on (p.60).

The volume varies depending on the input sources...

You can correct volume differences between input sources by utilizing “Input Trim” in

the “Option” menu (p.49).

HDMI Control does not work at all...

To use HDMI Control, you need to perform the HDMI Control link setup (p.79). After

connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit,

enable HDMI Control on each device and perform the HDMI Control link setup. This

setup is required every time you add a new HDMI Control-compatible device to your

system. For information on how HDMI Control works between your TV and playback

devices, refer to the instruction manuals for each device.

I want to change the input source name...

By default, input source names (such as “HDMI1” and “AV 1”) are displayed on the

front display when an input source is selected. If you want to rename them as you like,

use “Input Rename”

(p.62) in the “Setup” menu. You can also select a name from the

presets (such as “Blu-ray” and “DVD”).

I want to prevent accidental changes to the settings...

You can protect the settings configured on the unit (such as speaker settings) by

utilizing “Memory Guard” in the “

Setup” menu (p.63).

The unit’s remote control is simultaneously controlling another Yamaha

product as well as the unit...

When using multiple Yamaha products, the remote control may work on another

Yamaha product or another remote control may work on the unit. If this happens,

remote control (p.66).

The combination of video/audio input jacks does not match an external

device...

Use “Audio In” in the “Option” menu to change the combination of video/audio input

jacks so that it matches the output jack(s) of your external device (

p.21).

Video and audio are not synchronized...

Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output

(p.59).

I want to hear audio from the TV speakers...

Use “Audio Output” in the “Setup” menu to select the output destination of signals

input into the unit (p.57). Your TV speakers may be selected as an output destination.

I want to change the on-screen menu language...

Use “Language” in the “Setup” menu to select a language from English, Japanese,

French, German, Spanish, Russian, Italian and Chinese (

p.24).

I want to update the firmware...

Use “UPDATE” in the “ADVANCED SETUP” menu to update the unit’s firmware (p.67).

Troubleshooting

Refer to the table below when the unit does not function properly.

If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized

Yamaha dealer or service center.

First, check the following:

The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely.

The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on.

The connectors of each cable are securely inserted in to jacks on each device.

Power, system and remote control

Problem Cause Remedy

The power does not turn on.

The protection circuitry has been activated three times

consecutively.

As a safety precaution, capability to turn on the power is disabled. Contact your

nearest Yamaha dealer or service center to request repair.

The power does not turn off.

The internal microcomputer has frozen, due to an external electric

shock (such as lightning or excessive static electricity) or to a drop

in the power supply voltage.

Hold down z (power) on the front panel for more than 15 seconds to reboot the

unit. (If the problem persists, disconnect the power cable from the AC wall outlet

and plug it again.)

The power turns off (standby mode) immediately.

The unit was turned on while a speaker cable was shorted.

Twist the bare wires of each speaker cable firmly and reconnect to the unit and

speakers (

p.17).

The unit enters standby mode automatically.

The sleep timer worked. Turn on the unit and start playback again.

The auto-standby function activated because the unit was not used

for the specified time.

To disable the auto-standby function, set “Auto Power Standby” in the “Setup”

menu to “Off

” (p.61).

The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers (p.65).

The protection circuitry has been activated because of a short

circuit.

Twist the bare wires of each speaker cable firmly and reconnect to the unit and

speakers (p.

17).

The unit is not reacting.

The internal microcomputer is frozen, due to an external electric

shock (such as lightning or excessive static electricity) or to a drop

in the power supply voltage.

Hold down z (power) on the front panel for more than 15 seconds to reboot the

unit. (If the problem persists, disconnect the power cable from the AC wall outlet

and plug it again.)

Problem Cause Remedy

The unit cannot be controlled using the remote

control.

The unit is out of the operating range. Use the remote control within the operating range (p.4).

The batteries are weak. Replace with new batteries.

The unit’s remote control sensor is exposed to direct sunlight or

strong lighting.

Adjust the lighting angle, or reposition the unit.

The remote control IDs of the unit and the remote control are not

identical.

Change the remote control ID of the unit or the remote control (p.66).

Cannot select the desired input source even if

“INPUT” is pressed.

The function which skips some input sources is set. Set “Input Skip” of the desired input source in the “Setup” menu to “Off” (p.63).

The RED/GREEN/YELLOW/BLUE keys of the

remote control do not operate.

The device which is connected to the unit via HDMI does not

support the operation of the RED/GREEN/

YELLOW/BLUE keys.

Use a device which supports the operation of the RED/GREEN/YELLOW/BLUE

keys.

The settings of the RED/GREEN/YELLOW/BLUE keys of the unit's

remote control have been changed.

Set the “Remote Color Key” settings in the “Setup” menu to “Default” (p.64).

Audio

Problem Cause Remedy

No sound.

Another input source is selected. Select an appropriate input source with the input selection keys.

Signals that the unit cannot reproduce are being input.

Some digital audio formats cannot be played back on the unit. To check the

audio format of the input signal, use “Signal Info.” in the “Option” menu (

p.49).

The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.

The volume cannot be increased.

The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.60).

A device connected to the output jacks of the unit is not turned on. Turn on all devices connected to the output jacks of the unit.

No sound is coming from a specific speaker.

The playback source does not contain a signal for the channel. To check it, use “Signal Info.” in the “Option” menu (p.49).

The currently selected sound program/decoder does not use the

speaker.

To check it, select “5ch Stereo” (p.32).

Audio output of the speaker is disabled.

Perform YPAO (p.25) or use “Configuration” in the “Setup” menu to change the

speaker settings (p.54).

The volume of the speaker is set too low.

Perform YPAO (p.25) or use “Level” in the “Setup” menu to adjust the speaker

volume (

p.56).

The speaker cable connecting the unit and the speaker is

defective.

If there is no problem with the connection, replace with another speaker cable.

The speaker is malfunctioning.

To check it, replace with another speaker. If the problem persists, the unit may be

malfunctioning.

Problem Cause Remedy

No sound is coming from the subwoofer.

The playback source does not contain Low Frequency Effect (LFE)

or low-frequency signals.

To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the

front channel low-frequency components from the subwoofer (

p.55).

Subwoofer output is disabled. Perform YPAO (p.25) or set “Subwoofer” in the “Setup” menu to “Use” (p.54).

The volume of the subwoofer is too low. Adjust the volume on the subwoofer.

The subwoofer has been turned off by its auto-standby function. Disable the auto-standby function of the subwoofer or adjust its sensitivity level.

No sound from the playback device (connected to

the unit with HDMI).

The TV does not support HDCP (High-bandwidth Digital Content

Protection).

Refer to the instruction manuals for the TV and check the TV’s specifications.

The unit is set not to output audio input through HDMI jacks from

the SPEAKERS

terminals.

In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.57).

The number of devices connected to the HDMI OUT jack exceeds

the limit.

Disconnect some of the HDMI devices.

No sound from the TV (when HDMI Control is

used).

The TV is set to output audio from the TV speakers.

Change the audio output setting on your TV so that the TV audio is output from

the speakers connected to the unit.

A TV that does not support ARC is connected to the unit only with

an HDMI cable.

Use a digital optical cable to make an audio connection (p.19).

(If the TV is connected to the unit with an audio cable)

The TV audio input setting does not match the actual connection.

Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack

(p.57).

(If you are trying to use ARC)

ARC is disabled on the unit or TV.

Set “ARC” in the “Setup” menu to “On” (p.58). Also, enable ARC on the TV.

When playing back DSD audio, the unit disables

the audio output from a TV.

The unit does not support DSD audio output from a TV. Change the audio output setting on the playback device to PCM.

Only the front speakers work on multichannel

audio.

The playback device is set to output 2-channel audio (such as

PCM) only.

To check it, use “Signal Info.” in the “Option” menu (p.49). If necessary, change

the digital audio output setting on the playback device.

Noise/hum is heard.

The unit is too close to another digital or radio frequency device. Move the unit further away from the device.

The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.

The sound is distorted.

The volume of the unit is too high.

Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to

“Off

” (p.61).

A device connected to the unit’s output jacks is not turned on. Turn on all devices connected to the unit’s output jacks.

Video

Problem Cause Remedy

No video.

Another input source is selected on the unit. Select an appropriate input source with the input selection keys.

Another input source is selected on the TV. Switch the TV input to display the video from the unit.

The video signal output from the unit is not supported by the TV.

Check the video output setting of the playback device. For information about

video signals supported by the TV, refer to the instruction manuals for the TV.

The cable connecting the unit and TV (or playback device) is

defective.

If there is no problem with the connection, replace with another cable.

No video from the playback device (connected to

the unit with HDMI).

The input video signal (resolution) is not supported by the unit.

To check the information about the current video signal (resolution), use “Signal

Info.

” in the “Option” menu (p.49). For information about video signals supported

by the unit, see “HDMI signal compatibility” (p.81).

The TV does not support HDCP (High-bandwidth Digital Content

Protection).

Refer to the instruction manuals for the TV and check the TV’s specifications.

The number of devices connected to the HDMI OUT jack is over

the limit.

Disconnect some of the HDMI devices.

No image (contents required the HDCP 2.2 -

compatible HDMI device) from the playback

device connected to the unit with HDMI.

The TV (HDMI input jack) does not support HDCP 2.2. (The

Warning message can be displayed on the TV screen.)

Connect the unit to the TV (HDMI input jack) that supports HDCP 2.2.

The menu of the unit is not displayed on the TV.

The TV is not connected to the unit via HDMI.

You can display the menu of the unit on the TV only when they are connected

with an HDMI cable. If necessary, use an HDMI cable to connect them (

p.19 to

p.20).

Another input source is selected on the TV. Switch the TV input to display the video from the unit (HDMI OUT jack).

FM/AM radio

Problem Cause Remedy

FM radio reception is weak or noisy.

There is multi-path interference. Adjust the FM antenna height or orientation, or place it in a different location.

Your area is too far from the FM station transmitter.

To select monaural FM radio reception “FM Mode” in the “Option” menu to

“

Mono” (p.37).

Use an outdoor FM antenna.

AM radio reception is weak or noisy.

The noises may be caused by fluorescent lamps, motors,

thermostats, or other electrical equipment.

It is difficult to completely eliminate noise. It may be reduced by using an outdoor

AM antenna.

Radio stations cannot be selected automatically.

Your area is too far from the FM station transmitter.

Select the station manually (p.37).

Use an outdoor antenna. We recommend using a sensitive multi-element

antenna.

The AM radio signal is weak.

Adjust the AM antenna orientation.

Select the station manually (p.37).

Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with

the supplied AM antenna.

AM radio stations cannot be registered as

presets.

Auto Preset has been used.

Auto Preset is for registering FM radio stations only. Register AM radio stations

manually (

p.38).

USB (Except for USA, Canada, Australia models)

Problem Cause Remedy

The unit does not detect the USB device.

The USB device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again.

The file system of the USB device is not FAT 16 or FAT 32. Use a USB device with FAT 16 or FAT 32 format, except USB HDDs.

Folders and files in the USB device cannot be

viewed.

The folder structure not supported by the unit is applied.

The unit supports folder hierarchies of up to eight levels and up to 65,000 files

per level. If necessary, modify the folder structure on your USB device.

Bluetooth®

Problem Cause Remedy

Cannot make the unit pair with a Bluetooth

device.

Another Bluetooth device is connected. Terminate current Bluetooth connection, and perform pairing with the new device.

This unit and the device are too far apart. Move the device closer to this unit.

There is a device (microwave oven, wireless LAN, etc.) that outputs

signals in the 2.4 GHz frequency band nearby.

Move this unit away from the device that is emitting radio-frequency signals.

The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP.

Cannot make a Bluetooth connection.

Another Bluetooth device is connected.

Terminate current Bluetooth connection, then establish a Bluetooth connection

with that device again.

The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device.

The pairing information has been deleted.

Delete the pairing information of the device, and then perform pairing again

(p.42).

This unit can be paired with eight devices. If pairing with a ninth device is

performed, the pairing information with the earliest connection date will be

deleted.

This unit is not registered on the device’s Bluetooth connection list. Perform paring again (p.42).

No sound is produced, or the sound is

interrupted during playback.

The volume of the connecting device is set too low. Turn up the volume of the connecting device.

The connecting device is not set to send Bluetooth audio signals to

the unit.

Switch the output of Bluetooth audio signals of the connecting device to the unit.

The Bluetooth connection of the unit with the device has

terminated.

Perform Bluetooth connection operations again (p.43).

There is a device (microwave oven, wireless LAN, etc.) that outputs

signals in the 2.4 GHz frequency band nearby.

Move this unit away from the device that is emitting radio-frequency signals.

This unit and the connecting device are too far apart. Move the connecting device closer to this unit.

Error indications on the front display

Refer to the table below when the error message is indicated on the front display.

Message Cause Remedy

Access error

The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.

Check SP Wires

The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly.

Internal Error

An internal error has occurred. Contact the nearest authorized Yamaha dealer or service center.

No content

There are no playable files in the selected folder. Select a folder that contains files supported by the unit.

Not found

The Bluetooth device is not found.

• Place the Bluetooth device within 10 m (32 ft) of the Bluetooth receiver.

• Perform pairing again.

RemID Mismatch

The remote control IDs of the unit and the remote control are not

identical.

Change the remote control ID of the unit or the remote control (p.66).

Glossary

This is a glossary of the technical terms used in this manual.

Audio information

Audio decoding format

Dolby Digital

Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that

supports 5.1-channel audio. This technology is used for audio on most DVD disc.

Dolby Pro Logic II

Dolby Pro Logic II enables 5-channel playback from 2-channel sources. There are three modes

available: “Music mode” for music sources, “Movie mode” for movie sources, and “Game mode”

for game sources.

Dolby TrueHD

Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to

offer a high-definition home theater experience with the quality of the studio master. Dolby TrueHD

can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)

simultaneously. This technology is used for audio on BD (Blu-ray Disc).

DTS 96/24

DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit

audio. This format remains fully compatible with the existing multichannel audio systems that

support DTS Digital Surround. This technology is used for music DVDs, etc.

DTS Digital Surround

DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports

5.1-channel audio. This technology is used for audio on most DVD discs.

DTS-ES

DTS-ES creates total 6.1-channel audio from 5.1-channel sources that are recorded with DTS-ES.

This decoder adds a surround back sound to the original 5.1-channel sound. In the DTS-ES Matrix

6.1 format, a surround back sound is recorded in the surround channels, and in the DTS-ES

Discrete 6.1 format, a discrete surround back channel is recorded.

DTS Express

DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a

higher compression rate than the DTS Digital Surround format developed by DTS, Inc. This

technology is developed for audio streaming services on the Internet and secondary audio on BD

(Blu-ray Disc).

DTS-HD High Resolution Audio

DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that

supports 7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully

compatible with the existing multichannel audio systems that support DTS Digital Surround. This

technology is used for audio on most BD (Blu-ray Disc).

DTS-HD Master Audio

DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition

home theater experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio

can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)

simultaneously. This technology is used for audio on BD (Blu-ray Disc).

DTS Neo: 6

DTS Neo: 6 enables 6-channel playback from 2-channel sources. There are two modes available:

“Music mode” for music sources and “Cinema mode” for movie sources. This technology provides

discrete full-bandwidth matrix channels of surround sound.

DSD (Direct Stream Digital)

DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as

SACD (Super Audio CDs). The signals are stored at a high-frequency sampling rate of 2.8224

MHz. The highest frequency response is equal to or higher than 100 kHz, with a dynamic range of

120 dB. This technology offers better audio quality than that used for CDs.

MP3

One of the compressed digital audio format used by MPEG. With psychoacoustic technologies,

this compression method achieves a high compression rate. Reportedly, it is capable of

compressing data quantity by about 1/10 maintaining a certain level of audio quality.

MPEG-4 AAC

An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio

streaming services on Internet because it allows a high compression rate of data while

maintaining better audio quality than MP3.

PCM (Pulse Code Modulation)

PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted.

This technology is the basis of all other audio format. This technology is used as a lossless audio

format called Linear PCM for audio on a variety of media, including CDs and BD (Blu-ray Disc).

Sampling frequency/Quantization bit

Sampling frequency and quantization bits indicate the quantity of information when an analog

audio signal is digitized. These values are noted as in the following example: “48 kHz/24-bit”.

• Sampling frequency

Sampling frequency (the number of times the signal is sampled per second) is called the

sampling rate. When the sampling frequency is higher, the range of frequencies that can be

played back are wider.

• Quantization bit

The number of quantization bits indicate the degree of accuracy when converting the sound

level into a numeric value. When the number of quantized bits is higher, the expression of the

sound level is more accurate.

WAV

Windows standard audio file format, which defines the method of recording the digital data

obtained by converting audio signals. By default, the PCM method (no compression) is used, but

you can also use other compression methods.

WMA (Windows Media Audio)

One of the compressed digital audio formats developed by Microsoft Corporation. With

psychoacoustic technologies, this compression method achieves a high compression rate.

Reportedly, it is capable of compressing data quantity by about 1/20 maintaining a certain level of

audio quality.

Others

LFE (Low Frequency Effects) 0.1 channel

This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to

120 Hz. This channel is added to the channels for all bands with Dolby Digital or DTS to enhance

low frequency audio effects. This channel is labeled 0.1 because it is limited to only low frequency

audio.

Lip sync

Video output sometimes lags behind audio output due to the complexity of signal processing

caused by an increase in video signal capacity. Lip sync is a technique for automatically

correcting the timing lag between audio and video output.

HDMI and video information

Composite video signal

With the composite video signal system, color, brightness, and synchronization data signals are

combined and transmitted with a single cable.

Deep Color

Deep Color is a technology that HDMI specification supports. Deep Color increases the number of

available colors within the boundaries defined by the RGB or YCbCr color space. Conventional

color systems process the color using 8 bits. Deep Color processes the color with 10, 12, or 16

bits. This technology allows HDTVs and other displays to increase from millions of colors to

billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle

gradations between colors.

HDMI

HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/

video signal transmission. This interface transmits both digital audio and digital video signals

using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content

Protection) and provides a secure audio/video interface. For further information on HDMI, visit the

HDMI website at “http://www.hdmi.org/”.

x.v.Color

“x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color

space than sRGB and allows the expression of colors that were not hitherto possible. While

remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color

space, and thus can produce more vivid, natural images.

Yamaha technologies

CINEMA DSP (Digital Sound Field Processor)

Since the Dolby Surround and DTS systems were originally designed for use in movie theaters,

their effect is best experienced in a theater that has many speakers designed for acoustic effects.

Since home conditions (such as room size, wall material, and number of speakers) can differ so

widely, it is inevitable that there are differences in the sound that you hear. Based on a wealth of

actually measured data, CINEMA DSP, Yamaha’s original DSP technology provides the

audiovisual experience of a movie theater in your own home.

Compressed Music Enhancer

The Compressed Music Enhancer feature compensates for missing harmonics in compression

music formats (such as MP3). As a result, this technology provides improved performance for the

overall sound system.

SILENT CINEMA

Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones.

Parameters for headphones have been set for each sound program, so that accurate

representations of all the sound programs can be enjoyed on headphones.

Virtual CINEMA DSP

Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround

speakers with front left and right speakers. Even if the surround speakers are not connected, the

unit creates the realistic sound field in a listening room.

YPAO (Yamaha Parametric room Acoustic Optimizer)

The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections,

measures the distances from them to your listening position(s), and then automatically optimizes

the speaker settings, such as volume balance and acoustic parameters, to suit your room.

Supported devices and file formats

The following devices and file formats can be used by the unit.

Supported devices

USB devices (Except for USA, Canada, Australia models)

• This unit supports USB mass storage class devices (e.g., flash memories or

portable audio players) using FAT16 or FAT32 format.

• Do not connect devices other than USB mass storage class devices (such as USB

chargers or USB hubs), PCs, card readers, an external HDD, etc.

• USB devices with encryption cannot be used.

• Some features may not be compatible, depending on the model or manufacturer of

the USB storage device.

Bluetooth® devices

• Bluetooth devices that support A2DP can be used.

• Yamaha does not assure the connections of all Bluetooth devices.

File formats

USB (Except for USA, Canada, Australia models)

• The unit supports WAV (PCM format only), MP3, WMA and MPEG-4 AAC files (1- or

2-channel audio only).

• The unit is compatible with sampling rate of up to 48 kHz.

• Digital Rights Management (DRM) contents cannot be played back.

Video signal flow

Video signals input from a video device to the unit are output to a TV as shown below.

HDMIHDMI

VIDEOVIDEO

HDMI HDMI

VIDEO VIDEO

Video device The unit TV

HDMI connection

Composite video connection

HDMI in HDMI out

VIDEO in VIDEO out

Information on HDMI

The additional information on HDMI is as follows.

HDMI Control

HDMI Control allows you to operate external devices via HDMI. If you connect a TV

that supports HDMI Control to the unit with an HDMI cable, you can control the unit

(such as power and volume) with TV remote control operations. You can also control

playback devices (such as HDMI Control-compatible BD/DVD players) connected to

the unit with an HDMI cable.

Operations available from the TV’s remote control

• Standby synchronization

• Volume control including mute

• Switching to input audio from the TV when the TV input is switched to its built-in

tuner

• Switching to input video/audio from the selected playback device

• Switching between audio output devices (the unit or TV speaker)

(Example)

HDMI Control HDMI Control

The unit turns off

(standby)

Playback device

also turns off

Turn off the TV

Operations available from the unit’s remote control

• Starting playback on the playback device and turning on the TV with a scene

selection (

p.31)

• Switching the TV input to display the “Setup” menu (when SETUP is pressed)

• Controlling the playback device (playback and menu operations)

(Example)

HDMI Control HDMI Control

Press SCENE (BD/DVD)

Playback starts

Turns on and displays

video from the playback

device

To use HDMI Control, you need to perform the following HDMI Control link setup after

connecting the TV and playback devices.

For details on settings and operating your TV, refer to the instruction manual for the TV.

Note

This setup is required every time you add a new HDMI Control-compatible device to your system.

Turn on the unit, TV, and playback devices.

Configure the settings of the unit.

Switch the TV input to display video from the unit.

Press SETUP.

MUTE

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

TUNING

PRESET

MUTE

TUNING

MEMORY

TOP MENU

HOME

POP-UP/MENU

DISPLAYRETURN

SETUP

OPTION

ENTER

FM/AM

VOLUME

PROGR AM

USB

STRAIGHT

ENHANCER BASS

BLUETOOTH

INPU T

DVD

SC ENE

RADIO

SLEEP

BLUE

YELLOWGREEN

RED

MUTE

P MENU

HOME

POP-UP/MENU

DISPLA

DISPLADISPLA

DISPLA

DISPLADISPLA

DISPLA

RETURN

RETURNRETURN

RETURN

OPTION

SETUP

ENTER

Cursor keys

Use the cursor keys to select “HDMI” and press ENTER.

Setup

Speaker

HDMI

Sound

ECO

Function

Language

Back

RETURN

Use the cursor keys (q/w) to select “HDMI Control” and the cursor keys

(e/r) to select “On” as shown below.

Back

RETURN

HDMI

HDMI Control On

Audio Output

TV Audio Input AV2

Standby Sync Auto

ARC On

SCENE

If you made a digital optical cable connection between the TV and the

unit, use the cursor keys (q/w) to select “TV Audio Input” and the

cursor keys (e/r) to select “AUDIO1”.

Press SETUP.

Enable HDMI Control on the TV and playback devices (such as

HDMI Control-compatible BD/DVD players).

Turn off the main power of the TV and then turn off the unit and

playback devices.

Turn on the unit and playback devices and then turn on the TV.

Switch the TV input to display the video from the unit.

Check the followings.

On the unit: The input to which the playback device is connected is

selected. If not, select the input source manually.

On the TV: The video from the playback device is displayed.

Check that the unit is properly synchronized with the TV by

turning off the TV or adjusting the TV volume with the TV remote

control.

Note

▪ If HDMI Control does not work properly, try unplugging the TV in Step 2 and plugging in the TV again in

Step 3. It may solve the problem. Also, HDMI Control may not work if the number of connected devices

exceeds the limit. In this case, disable HDMI Control on the devices not in use.

▪ If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting

on the TV.

▪ If you reconnect the HDMI cable, perform the procedure 5-8 again.

▪ We recommend using TV and playback devices from the same manufacturer so that HDMI Control works

more effectively.

Audio Return Channel (ARC)

ARC allows you to input TV audio to the unit with the HDMI cable which transmits video

signal to the TV.

Check the following after the HDMI Control settings.

Select a TV program with the TV remote control.

Check that the input source of the unit will be automatically

switched to “AV 2” and the TV audio will be played back on the

unit.

If you cannot hear the TV audio, check the following:

▪ “ARC” (p.58) in the “Setup” menu is set to “On”.

▪ The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI

jack marked “ARC”) on the TV.

Some HDMI jack on the TV is not compatible with ARC. For details, refer

to the instruction manual for the TV.

Note

▪ If the audio is interrupted while using ARC, set “ARC” (p.58) in the “Setup” menu to “Off” and use a digital

optical cable to input TV audio to the unit (

p.19).

▪ When using ARC, connect a TV with an HDMI cable that supports ARC.

▪ “AV 2” is set as TV audio input at the factory. If you have connected any external device to the AV 2 jacks,

use “TV Audio Input” (p.57)

in the “Setup” menu to change the TV audio input assignment. To use the

SCENE function (p.31), you also need to change the input assignment for SCENE (TV).

HDMI signal compatibility

Audio signals

Audio signal type Audio signal format Compatible media (example)

2ch Linear PCM 2ch, 32 to 192 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio

Multichannel Linear PCM 8ch, 32 to 192 kHz, 16/20/24 bit

DVD-Audio, BD (Blu-ray disc),

HD DVD

DSD 2 to 5.1ch, 2.8224 MHz, 1 bit SACD

Bitstream Dolby Digital, DTS DVD-Video

Bitstream

(High definition audio)

Dolby TrueHD, Dolby Digital Plus,

DTS-HD Master Audio, DTS-HD

High Resolution Audio, DTS

Express

BD (Blu-ray disc), HD DVD

Video signals

The unit is compatible with the video signals of the following resolutions:

• VGA • 720p/60 Hz, 50 Hz

• 480i/60 Hz • 1080i/60 Hz, 50 Hz

• 576i/50 Hz • 1080p/60 Hz, 50 Hz, 24 Hz

• 480p/60 Hz • 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz

• 576p/50 Hz

Note

▪ When CPPM copy-protected DVD-Audio is played back, video/audio signals may not be output,

depending on the type of the DVD player.

▪ The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For details, refer to the

instruction manual for each device.

▪ To decode audio bitstream signals on the unit, set the input source device appropriately so that the device

outputs the bitstream audio signals directly (does not decode the bitstream signals on the playback

device). For details, refer to the instruction manual for the playback device.

Trademarks

The trademarks used in this manual are as follows.

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic, and the double-D symbol are trademarks of Dolby

Laboratories.

For DTS patents, see http://patents.dts.com.

Manufactured under license from DTS Licensing Limited. DTS,

DTS-HD, the Symbol, & DTS and the Symbol together are

registered trademarks of DTS, Inc.

Reserved.

HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

The Bluetooth

word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of such

marks by Yamaha Corporation is under license.

App Store is a service mark of Apple Inc.

Android™ is a trademark of Google Inc.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

Specifications

The specifications of this unit are as follows.

Input jacks

Analog Audio

• Audio x 3

Digital Audio (Supported frequencies: 32 kHz to 96 kHz)

• Optical x 1

• Coaxial x 2

Video

• Composite x 3

HDMI Input

• HDMI x 4

Other jacks

• USB x 1 (USB2.0) (Except for USA, Canada, Australia models)

Output jacks

Analog Audio

• Speaker Out x 5 (FRONT L/R, CENTER, SURROUND L/R)

• Subwoofer Out x 1

• Headphone x 1

Video

• Composite x 1

HDMI Output

• HDMI OUT x 1

Other jacks

YPAO MIC x 1

HDMI

HDMI Features:

• 4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC (Audio Return Channel), HDMI

Control (CEC), Auto Lip Sync, Deep Color, “x.v.Color”, HD audio playback, 21:9 Aspect Ratio,

BT.2020 Colorimetry, HDR Compatible

Video Format (Repeater Mode)

• VGA

• 480i/60 Hz

• 576i/50 Hz

• 480p/60 Hz

• 576p/50 Hz

• 720p/60 Hz, 50 Hz

• 1080i/60 Hz, 50 Hz

• 1080p/60 Hz, 50 Hz, 24 Hz

• 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz

Audio Format

• Dolby TrueHD

• Dolby Digital Plus

• Dolby Digital

• DTS-HD Master Audio

• DTS-HD High Resolution Audio

• DTS Express

• DTS

• DSD 2-ch to 6-ch

• PCM 2-ch to 8-ch (Max. 192 kHz/24-bit)

Content Protection: HDCP 2.2 compatible

Link Function: CEC supported

TUNER

Analog Tuner

• [U.K. and Europe models]

FM/AM with Radio Data System x 1 (TUNER)

• [Other models]

FM/AM x 1 (TUNER)

USB (Except for USA, Canada, Australia models)

Capable of Mass Storage Class USB Memory

Current Supply Capacity: 0.5 A

Bluetooth

Bluetooth version

• Ver. 2.1+EDR

Supported profile

• A2DP

Supported codec

• SBC

Wireless output

• Bluetooth Class 2

Maximum communication distance

• 10 m (33 ft) without interference

Compatible Decoding Formats

Decoding Format

• Dolby TrueHD, Dolby Digital Plus

• Dolby Digital

• DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Express

• DTS, DTS 96/24, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1

Post Decoding Format

• Dolby Pro Logic

• Dolby Pro Logic II Music, Dolby Pro Logic II Movie, Dolby Pro Logic II Game

• DTS Neo: 6 Music, DTS Neo: 6 Cinema

Audio Section

Rated Output Power (2-channel driven)

• [U.S.A. and Canada models] (20 Hz to 20 kHz, 0.09% THD, 8 Ω)

• [Other models] (20 Hz to 20 kHz, 0.09% THD, 6 Ω)

– Front L/R 70 W+70 W

• [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω)

– Front L/R 85 W+85 W

– Center 85 W

– Surround L/R 85 W+85 W

Rated Output Power (1-channel driven)

• [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω)

• [Other models] (1 kHz, 0.9% THD, 6 Ω)

– Front L/R 100 W/ch

– Center 100 W/ch

– Surround L/R 100 W/ch

Maximum Effective Output Power (1-channel driven)

• [U.S.A. and Canada models]

(1 kHz, 10% THD, 8 Ω)

– Front L/R, Center, Surround L/R

130 W/ch

(1 kHz, 10% THD, 6 Ω)

– Front L/R, Center, Surround L/R

140 W/ch

• [Other models] (1 kHz, 10% THD, 6 Ω)

– Front L/R, Center, Surround L/R 135 W/ch

Dynamic Power (IHF)

• [U.S.A. and Canada models]

– Front L/R (8/6/4/2 Ω)

110/130/160/180 W

• [Other models]

– Front L/R (6/4/2 Ω)

110/130/150 W

Damping Factor

• Front L/R, 20 Hz to 20 kHz, 8 Ω

100 or more

Input Sensitivity / Input Impedance

• AV 2 etc. (1 kHz, 100 W/6 Ω) 200 mV/47 kΩ

Maximum Input Signal

• AV 2 etc. (1 kHz, 0.5% THD, Effect On) 2.3 V

Output Level / Output Impedance

• SUBWOOFER

1 V/1.2 kΩ

Headphone Jack Rated Output / Impedance

• AV 2 etc. (1 kHz, 50 mV, 8 Ω) 100 mV/470 Ω

Frequency Response

• AV 2 etc. to Front (10 Hz to 100 kHz) +0/-3 dB

Signal to Noise Ratio (IHF-A Network)

• AV 2 etc. (Input 1 kΩ Shorted, Speaker Out)

110 dB or more

Residual Noise (IHF-A Network)

• Front L/R (Speaker Out) 150 μV or less

Channel Separation

• AV 2 etc. (Input 1 kΩ Shorted, 1 kHz/10 kHz)

70 dB/50 dB or more

Volume Control

• Range MUTE, -80 dB to +16.5 dB

• Step 0.5 dB

Tone Control Characteristics

• Bass Boost/Cut ±6 dB/0.5 dB Step at 50 Hz

• Bass Turnover 350 Hz

• Treble Boost/Cut ±6 dB/0.5 dB Step at 20 kHz

• Treble Turnover 3.5 kHz

Filter Characteristics

(fc=40/60/80/90/100/110/120/160/200 Hz)

• H.P.F. (Front, Center, Surround) 12 dB/oct.

• L.P.F. (Subwoofer) 24 dB/oct.

Video Section

Video Signal Type

• [U.S.A., Canada, Korea, Taiwan, Brazil and General models] NTSC

• [Other models] PAL

Video Signal Level

• Composite

1 Vp-p/75 Ω

Video Maximum Input Level

1.5 Vp-p or more

Video Signal to Noise Ratio

50 dB or more

FM Section

Tuning Range

• [U.S.A. and Canada models] 87.5 MHz to 107.9 MHz

• [Asia, Taiwan, Brazil and General models] 87.5/87.50 MHz to 108.0/108.00 MHz

• [Other models] 87.50 MHz to 108.00 MHz

50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.)

• Mono 3 μV (20.8 dBf)

Signal to Noise Ratio (IHF)

• Mono 65 dB

• Stereo 64 dB

Harmonic Distortion (IHF, 1 kHz)

• Mono 0.5%

• Stereo 0.6%

Antenna Input

75 Ω unbalanced

AM section

Tuning Range

• [U.S.A. and Canada models] 530 kHz to 1710 kHz

• [Asia, Taiwan, Brazil and General models] 530/531 kHz to 1710/1611 kHz

• [Other models] 531 kHz to 1611 kHz

General

Power Supply

• [U.S.A. and Canada models] AC 120 V, 60 Hz

• [Taiwan, Brazil and General model] AC110 to 120/220 to 240 V, 50/60 Hz

• [Korea model] AC 220 V, 60 Hz

• [Australia model] AC 240 V, 50 Hz

• [U.K. and Europe models] AC 230 V, 50 Hz

• [Asia model] AC 220 to 240 V, 50/60 Hz

Power Consumption

260 W

Standby Power Consumption

• HDMI Control Off

– [Taiwan, Brazil and General model] 0.5 W

– [Other models] 0.3 W

• HDMI Control On (No Signals) 0.9 W

Maximum Power Consumption

• [Taiwan, Brazil and General models] 470 W

Dimensions (W x H x D)

435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”)

Weight

7.4 kg (16.3 lbs)

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain

the latest manual, access the Yamaha website then download the manual file.

Yamaha Global Site

http://www.yamaha.com/

Yamaha Downloads

http://download.yamaha.com/

Manual Development Department

Published 01/2016 NV-A0

YH631A0/EN2

Transcripción de documentos

AV Receiver Owner's Manual Read the supplied booklet “Safety Brochure” before using the unit. EN CONTENTS BEFORE USING THE UNIT 4 6 7 Accessories................................................................................................ 4 Optimizing the speaker settings automatically (YPAO)................ 25 Error messages....................................................................................................................................................................... 27 How to use this manual............................................................................ 4 Warning messages................................................................................................................................................................ 28 Remote control.......................................................................................... 4 PLAYBACK Insert the batteries................................................................................................................................................................... 4 Operating range of the remote control........................................................................................................................... 4 FEATURES Selecting an on-screen menu language.......................................... 24 29 Basic playback procedure...................................................................... 29 5 Enjoying playback................................................................................................................................................................. 29 What you can do with the unit................................................................. 5 Selecting the input source and favorite settings with one touch (SCENE).................................................................................................... 31 Switching information on the front display................................................................................................................. 30 Part names and functions......................................................................... 7 Selecting a registered scene.............................................................................................................................................. 31 Front panel................................................................................................................................................................................. 7 Registering a scene............................................................................................................................................................... 31 Front display (indicators)....................................................................................................................................................... 8 Rear panel................................................................................................................................................................................... 9 Selecting the sound mode..................................................................... 32 Remote control....................................................................................................................................................................... 10 Enjoying sound field effects (CINEMA DSP)................................................................................................................. 33 PREPARATIONS 1 2 Enjoying unprocessed playback...................................................................................................................................... 35 11 Enhancing the bass (Extra Bass)....................................................................................................................................... 36 Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer)..................................................................................................................................................................... 36 Placing speakers............................................................................... 12 Typical speaker layouts....................................................................................................................................................... 13 Listening to FM/AM radio....................................................................... 37 Other speaker layouts.......................................................................................................................................................... 14 Setting the frequency steps............................................................................................................................................... 37 Setting the speaker impedance....................................................................................................................................... 15 Selecting a frequency for reception............................................................................................................................... 37 Connecting speakers........................................................................ 16 Registering favorite radio stations (presets)................................................................................................................ 38 Radio Data System tuning.................................................................................................................................................. 41 Connecting speaker cables................................................................................................................................................ 17 3 Connecting the subwoofer (with built-in amplifier)................................................................................................. 17 Playing back music stored on a Bluetooth® device.............................. 42 Connecting a TV/playback devices.................................................. 18 Playback of Bluetooth® device contents....................................................................................................................... 43 Connecting a Bluetooth® device (pairing).................................................................................................................... 42 Input/output jacks and cables.......................................................................................................................................... 18 Disconnecting a Bluetooth® connection....................................................................................................................... 43 Connecting a TV..................................................................................................................................................................... 19 Playing back music stored on a USB storage device (Except for USA, Canada, Australia models)..................................................................... 44 Connecting video devices (such as BD/DVD players).............................................................................................. 20 Connecting audio devices (such as CD players)......................................................................................................... 22 Connecting a USB storage device................................................................................................................................... 44 Connecting to the jack on the front panel................................................................................................................... 22 4 Connecting the FM/AM antennas.................................................... 23 5 Connecting the power cable............................................................ 23 Playback of USB storage device contents..................................................................................................................... 44 2 En Configuring playback settings for different playback sources (Option menu)......................................................................................... 47 Glossary................................................................................................... 76 Option menu items............................................................................................................................................................... 47 HDMI and video information............................................................................................................................................. 77 CONFIGURATIONS Audio information................................................................................................................................................................. 76 Yamaha technologies.......................................................................................................................................................... 77 51 Supported devices and file formats...................................................... 78 Supported devices................................................................................................................................................................ 78 Configuring various functions (Setup Menu)....................................... 51 File formats.............................................................................................................................................................................. 78 Setup menu items................................................................................................................................................................. 52 Video signal flow.................................................................................... 78 Speaker...................................................................................................................................................................................... 54 HDMI........................................................................................................................................................................................... 57 Information on HDMI.............................................................................. 79 Sound......................................................................................................................................................................................... 59 HDMI Control.......................................................................................................................................................................... 79 ECO............................................................................................................................................................................................. 61 Audio Return Channel (ARC)............................................................................................................................................. 81 Function.................................................................................................................................................................................... 62 HDMI signal compatibility.................................................................................................................................................. 81 Language.................................................................................................................................................................................. 64 Trademarks............................................................................................. 82 Configuring the system settings (ADVANCED SETUP menu).............. 65 Specifications.......................................................................................... 83 ADVANCED SETUP menu items........................................................................................................................................ 65 Changing the speaker impedance setting (SP IMP.)................................................................................................. 65 Selecting the remote control ID (REMOTE ID)............................................................................................................. 66 Changing the FM/AM tuning frequency setting (TU)............................................................................................... 66 Switching the video signal type (TV FORMAT)............................................................................................................ 66 Selecting the HDMI 4K signal format (4K MODE)....................................................................................................... 66 Restoring the default settings (INIT)............................................................................................................................... 67 Updating the firmware (UPDATE) (Except for USA, Canada, Australia models)............................................. 67 Checking the firmware version (VERSION)................................................................................................................... 67 APPENDIX 68 Frequently asked questions................................................................... 68 Troubleshooting..................................................................................... 69 First, check the following:................................................................................................................................................... 69 Power, system and remote control................................................................................................................................. 69 Audio.......................................................................................................................................................................................... 70 Video.......................................................................................................................................................................................... 72 FM/AM radio............................................................................................................................................................................ 73 USB (Except for USA, Canada, Australia models)........................................................................................................ 73 Bluetooth®................................................................................................................................................................................ 74 Error indications on the front display................................................... 75 3 En BEFORE USING THE UNIT Accessories Remote control Check that the following accessories are supplied with the product. The supplied remote control is used as follows. £ AM antenna Insert the batteries £ FM antenna Insert the batteries the right way round. * One of the above is supplied depending on the region of purchase. £ YPAO microphone £ Remote control £ Batteries (AAA, R03, UM-4) (x2) Operating range of the remote control £ CD-ROM (Owner's Manual) £ Easy Setup Guide Point the remote control at the remote control sensor on the unit and remain within the operating range shown below. £ Safety Brochure How to use this manual • Some features are not available in certain regions. Within 6 m (20 ft) • Due to product improvements, specifications and appearance are subject to change without notice. 30° • This manual explains operations using the supplied remote control. Notice: Indicates precautions for use to avoid the possibility of malfunction/damage to the unit. Note: Indicates instructions and supplementary explanations for optimum use. 4 En 30° FEATURES What you can do with the unit The unit is equipped with full of useful functions. Supports 2- to 5.1-channel speaker system The ECO mode (power saving function) allows you to create an eco-friendly home theater system You can enjoy your favorite acoustic spaces in various styles. When the ECO mode is enabled, you can reduce the unit's power consumption. • “ECO Mode” (p.61) YPAO automatically optimizes the speaker settings to suit your room. Sequential operation of a TV, AV receiver, and BD/DVD player (HDMI Control) • “Optimizing the speaker settings automatically (YPAO)” (p.25) CINEMA DSP allows you to create stereo or multichannel sounds with the sound fields like actual movie theaters and concert halls in your own room. When the unit is connected to an HDMI Control-compatible TV and BD/DVD player with each HDMI cable, you can control the unit (such as power and volume) and BD/DVD player with TV remote control operations. • “Enjoying sound field effects (CINEMA DSP)” (p.33) • “HDMI Control” (p.79) You can enjoy compressed music with enhanced sound (Compressed Music Enhancer). Supports Bluetooth® devices • “Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer)” (p.36) You can play back music stored on a Bluetooth device. Change the input source and favorite settings with one touch (SCENE) • “Playing back music stored on a Bluetooth® device” (p.42) Supports USB storage devices The SCENE function allows you to select the input source and settings registered to the corresponding scene, such as sound program and Compressed Music Enhancer on/off, with just one touch. You can play back music stored on a USB storage device. • “Playing back music stored on a USB storage device (Except for USA, Canada, Australia models)” (p.44) • “Selecting the input source and favorite settings with one touch (SCENE)” (p.31) Connecting various devices 4K Ultra HD signal and HDCP 2.2 supported A number of HDMI jacks and various input/output jacks on the unit allow you to connect video devices (such as BD/DVD players), audio devices (such as CD players), game consoles, portable audio player, and other devices. You can enjoy the high definition video quality of 4K with HDCP 2.2 that complies with the latest copyright protection. • “Selecting the HDMI 4K signal format (4K MODE)” (p.66) • “Connecting a TV/playback devices” (p.18) 5 En Playing back TV audio in surround sound with a single HDMI cable connection (Audio Return Channel: ARC) Useful applications The useful application for connections and operations of the unit is as follows. n Application for tablets “AV SETUP GUIDE” When using an ARC -compatible TV, you only need one HDMI cable to enable video output to the TV, audio input from the TV, and the transmission of HDMI Control signals. AV SETUP GUIDE is an application that assists you with cable connections between AV Receiver and source devices as well as AV Receiver setup. This app guides you through the various settings such as speaker connections, TV and source device connections. • “Connecting a TV” (p.19) Surround playback with 5 speakers placed in front Functions: 1) Connection support guide – Speaker connection – TV/source devices connection You can enjoy the surround sound even when the surround speakers are placed in front. • “Enjoying sound field effects without surround speakers (Virtual CINEMA DSP)” (p.34) 2) Setup support guide – Various setup assistance with illustrations. – YPAO setting guidance Enhanced bass reproduction 3) View Owner's Manual Extra Bass allows you to enjoy enhanced bass reproduction that does not depend on the speakers used. • “Enhancing the bass (Extra Bass)” (p.36) * This application is for tablets only. Listening to FM/AM radio For details, search for “AV SETUP GUIDE” on the App Store or Google Play™. The unit is equipped with a built-in FM/AM tuner. You can register up to 40 favorite radio stations as presets. • “Listening to FM/AM radio” (p.37) Easy operation with a TV screen You can operate the USB storage device, view information, or easily configure the settings using the on-screen menu. Auto Rename function The unit creates an input source name, displayed on the front display, automatically according to the connected HDMI-compatible device. • “Input Rename” (p.62) 6 En Part names and functions The part names and functions of the unit and the supplied remote control are as follows. Front panel 1 2 3 4 5 6 7 8 9 YPAO MIC INFO MEMORY (PAIRING) PRESET FM AM TUNING VOLUME SCENE BD DVD CD TV RADIO AUX PHONES INPUT TONE CONTROL USB STRAIGHT PROGRAM SILENT CINEMA AUDIO 0 1 z (power) key Turns on/off (standby) the unit. 2 YPAO MIC jack For connecting the supplied YPAO microphone (p.25). 3 Remote control sensor Receives remote control signals (p.4). 4 INFO key Selects the information displayed on the front display (p.30). 5 MEMORY (PAIRING) key Registers FM/AM radio stations as preset stations (p.38). Starts pairing with a Bluetooth device by holding down for 3 seconds (p.42). 6 PRESET keys Select a preset FM/AM radio station (p.40). 7 FM and AM keys Switch between FM and AM (p.37). A BC D E F G H E STRAIGHT key 8 TUNING keys Select the radio frequency (p.37). Enables/disables the straight decode mode (p.35). F AUX jack 9 Front display For connecting devices, such as portable audio players (p.22). Displays information (p.8). : PHONES jack G USB jack For connecting headphones. For connecting a USB storage device (p.44). A INPUT keys H VOLUME knob Select an input source. Adjusts the volume. B TONE CONTROL key Adjusts the high-frequency range and low-frequency range of output sounds (p.48). C SCENE keys Select the registered input source and sound program with one touch. Also, turns on the unit when it is in standby mode (p.31). D PROGRAM keys Select a sound program or a surround decoder (p.32). 7 En Front display (indicators) 2 1 3 4 5 ENHANCER STEREO TUNED OUT 6 7 8 SLEEP MUTE VOL. ADAPTIVE DRC SL 9 A 0 1 HDMI Lights up when HDMI signals are being input or output. OUT Lights up when HDMI signals are being output. 2 ENHANCER Lights up when Compressed Music Enhancer (p.36) is working. 3 CINEMA DSP Lights up when CINEMA DSP (p.33) is working. 4 STEREO Lights up when the unit is receiving a stereo FM radio signal. 0 : Cursor indicators Indicate the remote control cursor keys currently operational. A Information display Displays the current status (such as input name and sound mode name). You can switch the information by pressing INFO (p.30). B Speaker indicators Indicate speaker terminals from which signals are output. A Front speaker (L) S Front speaker (R) D Center speaker TUNED F Surround speaker (L) Lights up when the unit is receiving an FM/AM radio station signal. G Surround speaker (R) 5 Bluetooth indicator Light up while the unit is connecting to a Bluetooth device. L Subwoofer C ADAPTIVE DRC Lights up when Adaptive DRC (p.48) is working. 6 SLEEP Lights up when the sleep timer is on. 7 MUTE Blinks when audio is temporarily muted. 8 Volume indicator Indicates the current volume. 9 ECO Lights up when the eco mode (p.61) is enabled. 8 En L C R SW SR B C Rear panel 2 1 5 ▪ The area around the video/audio output jacks is marked in white on the actual product to prevent improper connections. 6 3 7 4 8 7 SUBWOOFER PRE OUT jack For connecting to a subwoofer (with built-in amplifier) (p.16). 8 SPEAKERS terminals 1 HDMI OUT jack For connecting to an HDMI-compatible TV and outputting video/audio signals (p.18). When using ARC, TV audio signal can also be input through the HDMI OUT jack. 2 HDMI 1–4 jacks For connecting to speakers (p.16). 9 VOLTAGE SELECTOR (Taiwan, Brazil and General models only) Selects the switch position according to your local voltage (p.23). For connecting to HDMI-compatible playback devices and inputting video/audio signals (p.19). 3 ANTENNA jacks For connecting to FM and AM antennas (p.23). 4 Power cable For connecting to an AC wall outlet (p.23). 5 AV jacks AUDIO jacks For connecting to video/audio playback devices and inputting video/audio signals (p.20). 6 MONITOR OUT jacks For connecting to a TV and outputting video signals (p.18). 9 En 9 Remote control 1 1 Remote control signal transmitter B MUTE key 2 SLEEP key 2 0 SLEEP SCENE 3 BD DVD TV STRAIGHT 4 CD RADIO ENHANCER BASS Pressing this key repeatedly will specify the time (120 min, 90 min, 60 min, 30 min, off), in which the unit switches to the standby mode. 3 SCENE keys Select the registered input source and sound program with one touch. Also, turn on the unit when it is in standby mode (p.31). PROGRAM 4 Sound mode keys FM/AM Select a sound mode (p.32). USB 5 INPUT VOLUME A BLUETOOTH 5 Input selection keys Select an input source for playback. 6 SETUP key MUTE 6 Displays the setup menu (p.51). 7 Menu operation keys SETUP OPTION ENTER 7 RETURN TOP MENU DISPLAY HOME POP-UP/MENU 8 RED GREEN YELLOW BLUE MEMORY 9 B TUNING TUNING PRESET C A VOLUME keys Adjust the volume. Transmits infrared signals. Cursor keys Select a menu or the parameter. ENTER Confirms a selected item. RETURN Returns to the previous screen. 789 External device operation keys Let you perform playback operations when “USB” is selected as the input source, or control playback of the HDMI Control-compatible playback device. Note ▪ The playback devices must support HDMI Control. Some HDMI Control-compatible devices cannot be used. ▪ You can assign the unit's functions to the RED/GREEN/ YELLOW/BLUE keys (p.64). 9 Radio keys Operate the FM/AM radio when “TUNER” is selected as the input source (p.37). MEMORY Registers FM/AM radio stations as presets. PRESET Select a preset station. TUNING Select the radio frequency. : z (receiver power) key Turns on/off (standby) the unit. 10 En Mutes the audio output. C OPTION key Displays the option menu (p.47). PREPARATIONS General setup procedure 1 Placing speakers................................................................................................................................ (p.12) 2 Connecting speakers........................................................................................................................ (p.16) 3 Connecting a TV/playback devices.................................................................................................. (p.18) 4 Connecting the FM/AM antennas.................................................................................................... (p.23) 5 Connecting the power cable............................................................................................................ (p.23) 6 Selecting an on-screen menu language.......................................................................................... (p.24) 7 Optimizing the speaker settings automatically (YPAO)................................................................ (p.25) This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit! 11 En 1 Placing speakers Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer in your room. This section describes the representative speaker layout examples. Notice ▪ (U.S.A. and Canada models only) Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.15). ▪ (Except for U.S.A. and Canada models) Use speakers with an impedance of at least 6 W. ▪ Use a subwoofer with built-in amplifier. ▪ Be sure to connect the front left and right speakers. 12 En Typical speaker layouts n 5.1-channel system n 5.1-channel system (Virtual CINEMA FRONT) We recommend this speaker layout which can maximize the performance of the unit. We recommend this speaker layout when the speakers can't be placed in back of the room. 1 1 2 2 4 9 9 3 4 5 10° to 30° Speaker type Front (L/R) Center Surround (L/R) Subwoofer 5 3 Abbr. 1/2 3 4/5 9 10° to 30° Speaker type Function Produce front left/right channel sounds (stereo sounds). Front (L/R) Produces center channel sounds (such as movie dialogue and vocals). Center Produce surround left/right channel sounds. Surround (L/R) Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels. Subwoofer This channel is counted as “0.1”. Abbr. 1/2 3 4/5 9 Function Produce front left/right channel sounds (stereo sounds). Produces center channel sounds (such as movie dialogue and vocals). Produce surround left/right channel sounds. By this system, place the surround speakers in front. Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels. This channel is counted as “0.1”. Note Note ▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system). ▪ To utilize this configuration, set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On”. ▪ You can place the subwoofer either in the left or right side. ▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system). ▪ You can place the subwoofer either in the left or right side. 13 En Other speaker layouts The following speaker layouts are also available. n 2.1-channel system n 3.1-channel system 1 9 2 1 3 9 14 En 2 Setting the speaker impedance (U.S.A. and Canada models only) Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the speaker impedance to “6 Ω MIN”. 1 2 Before connecting speakers, connect the power cable to an AC wall outlet. While holding down STRAIGHT on the front panel, press z (power). z (power) STRAIGHT 3 Check that “SP IMP.” is displayed on the front display. CHARGE OUT 1 2 ECO ENHANCER STEREO TUNED PARTY SLEEP MUTE ZONE ZONE 2 A 3 B VOL. SP IMP.••8¬MIN 4 5 ADAPTIVE DRC VIRTUAL Press STRAIGHT to select “6 Ω MIN”. Press z (power) to set the unit to standby mode and remove the power cable from the AC wall outlet. You are now ready to connect the speakers. 15 En 2 Connecting speakers Connect the speakers placed in your room to the unit. The following diagrams provide connections for a 5.1-channel system as an example. For other systems, connect speakers while referring to the connection diagram for the 5.1-channel system. Notice ▪ Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before connecting the speakers. ▪ The speaker has the polarity (+/-). Connect the speaker cable correctly between the positive (+) terminal of the unit and the speaker, and also between the negative (-) terminal of them. Cables required for connection (commercially available) Speaker cables (x the number of speakers) + – Audio pin cable (x1: for connecting a subwoofer) + – The unit (rear) Precaution for connecting of the speaker cables 1 2 3 4 1 10 mm (3/8”) 10 mm (3/8”) Improper connecting of the speaker cables may cause short circuit and also damage the unit or the speakers. 2 ▪ Twist the bare wires of the speaker cables firmly together. 3 4 ▪ Do not let the core wires of the speaker cable touch one another. ▪ Do not let the core wires of the speaker cable come into contact with the unit’s metal parts (rear panel and screws). Audio pin cable Use a subwoofer with built-in amplifier. 9 Subwoofer 5 Surround (R) 4 Surround (L) 3 2 1 Center Front (R) Front (L) 16 En If “Check SP Wires” appear on the front display when the unit is turned on, turn off the unit, and then check the speaker cables short circuit. n Connecting center/surround speakers Connecting speaker cables 1 Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive terminal. 2 3 4 n Connecting front speakers 1 2 3 4 Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable, and twist the bare wires of the cable firmly together. Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable, and twist the bare wires of the cable firmly together. Press down the tab. Insert the bare wires of the cable into the hole in the terminal. Release the tab. SU RR OU ND Loosen the speaker terminal. ER d Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. FR ON T d a Audio pin cable AV 2 AV 3 Using a banana plug (U.S.A., Canada, Australia, Taiwan, Brazil and General models only) Tighten the speaker terminal. Insert a banana plug into the end of the terminal. a - (black) Use an audio pin cable to connect the subwoofer. - (black) 1 2 + (red) Connecting the subwoofer (with built-in amplifier) c b b c Tighten the terminal. + (red) CE NT a FR ON T Banana plug b 17 En 3 Connecting a TV/playback devices The unit is equipped with a variety of input jacks including HDMI input jacks to allow you to connect different types of playback devices. For information on how to connect a Bluetooth device or a USB storage device, see the following pages. • Connecting a Bluetooth device (p.42) • Connecting a USB storage device (p.44) n Video jacks HDMI jacks Transmit digital video and digital sound through a single jack. Use an HDMI cable. HDMI cable Transmit analog video signals. Use a video pin cable. ▪ The unit’s HDMI jacks support the HDMI Control, Audio Return Channel (ARC), and 3D and 4K Ultra HD video transmission (through output) features. ▪ Use high speed HDMI cables to enjoy 3D or 4K Ultra HD videos. Transmit analog stereo audio signals. Use a stereo pin cable (RCA cable). Stereo pin cable Video pin cable n Audio jacks (Stereo mini jack) Transmits analog stereo audio signals. Use a stereo mini-plug cable. OPTICAL jacks Transmit digital audio signals. Use a digital optical cable. Remove the tip protector (if available) before using the cable. Digital optical cable Note ▪ Use a 19-pin HDMI cable with the HDMI logo. We recommend using a cable less than 5.0 m (16.4 ft) long to prevent signal quality degradation. (Stereo L/R jacks) VIDEO jacks Input/output jacks and cables n Video/audio jacks AUDIO jacks OPTICAL COAXIAL jacks Transmit digital audio signals. Use a digital coaxial cable. Digital coaxial cable 18 En Stereo mini-plug cable Connecting a TV n Composite video connection Connect a TV to the unit so that video input to the unit can be output to the TV. You can also enjoy playback of TV audio on the unit. When connecting any video device with a video pin cable, connect the TV to the MONITOR OUT (VIDEO) jack. To maximize the performance of the unit, we recommend connecting a TV with an HDMI cable. Note n HDMI connection ▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI. ▪ If you connect your TV to the unit with a cable other than HDMI, video input to the unit via HDMI cannot be output to the TV. ▪ If you will receive TV broadcasts only from the set-top box, you do not need to make an audio cable connection between the TV and the unit. Connect the TV to the unit with an HDMI cable and a digital optical cable. The unit (rear) HDMI OUT jack VIDEO (composite video) connection HDMI input Connect the TV to the unit with a video pin cable and a digital optical cable. HDMI HDMI HDMI The unit (rear) Video input (composite video) MONITOR OUT (VIDEO) jack VIDEO OPTICAL O V V MONITOR OUT O OPTICAL (TV) AUDIO 1 TV AUDIO 1 (OPTICAL) jack Audio output (digital optical) OPTICAL O Note O OPTICAL (TV) AUDIO 1 ▪ You do not make a digital optical cable connection between the TV and the unit in the following cases: AUDIO 1 (OPTICAL) jack – If your TV supports Audio Return Channel (ARC) – If you will receive TV broadcasts only from the set-top box ▪ If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s power and volume with the TV’s remote control. To use HDMI Control and ARC, you need to configure the HDMI settings on the unit. For details on the settings, see “Information on HDMI” (p.79). About Audio Return Channel (ARC) ▪ ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a single HDMI cable, you can output video/audio to the TV or input TV audio to the unit. ▪ When using ARC, connect a TV with an HDMI cable that supports ARC. 19 En TV Audio output (digital optical) Connecting video devices (such as BD/DVD players) n Composite video connection Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the unit. Depending on the video/audio output jacks available on your video device, choose one of the following connections. We recommend using an HDMI connection if the video device has an HDMI output jack. Connect a video device to the unit with a video pin cable and an audio cable (digital coaxial or stereo pin cable). Choose a set of input jacks (on the unit) depending on the audio output jacks available on your video device. Output jacks on video device Video Note If the combination of video/audio input jacks available on the unit does not match your video device, change its combination according to the output jacks of your device (p.21). Input jacks on the unit Audio Digital coaxial Composite video n HDMI connection AV 1 (VIDEO + COAXIAL) Analog stereo AV 2–3 (VIDEO + AUDIO) Digital optical You need to change the combination of video/audio input jacks (p.21). Connect a video device to the unit with an HDMI cable. Video output (composite video) AV 1–3 (VIDEO) jacks HDMI 1–4 jacks VIDEO The unit (rear) V V VIDEO The unit (rear) HDMI OUT jack HDMI Video device HDMI C C COAXIAL HDMI COAXIAL L L L L R R R R Video device AV 1 (COAXIAL) jack or AV 2–3 (AUDIO) jacks If you select HDMI 1–4 as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Audio output (digital coaxial or analog stereo) If you select AV 1-3 as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Note To watch videos input to the HDMI 1–4 jacks, you need to connect your TV to the HDMI OUT jack of the unit (p.19). Note To watch videos input to the AV 1–3 (VIDEO) jacks, you need to connect your TV to the MONITOR OUT (VIDEO) jack of the unit (p.19). 20 En n Changing the combination of video/audio input jacks 3 If the combination of video/audio input jacks available on the unit does not match your video device, change its combination according to the output jacks of your device. You can connect a video device that has the following video/audio output jacks. Output jacks on video device Press OPTION. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS MUTE OPTION PROGRAM FM/AM Input jacks on the unit SETUPP USB INPUT OPTION VOLUME BLUETOOTH Video HDMI Composite video Audio Video Audio Digital optical HDMI 1–4 AUDIO 1 (OPTICAL) Digital coaxial HDMI 1–4 AUDIO 2 (COAXIAL) AV 1 (COAXIAL) Analog stereo HDMI 1–4 AV 2–3 (AUDIO) Digital optical AV 1–3 (VIDEO) AUDIO 1 (OPTICAL) MUTE SETUP RETURN ENTER DISPLAY TOP MENU HOME POP-UP/MENU RETURN RED GREEN YELLOW DISPLAYY DISPLA BLUE MEMORY TUNING TUNING TOP MENU 4 For example, if you have connected a video device to AV 2 (VIDEO) and AUDIO 1 (OPTICAL) jack of the unit, change the combination setting as follows. ENHANCER STEREO TUNED SLEEP MUTE OUT VOL. ECO ADAPTIVE DRC VIRTUAL Audio In 5 VIDEO V V Use the cursor keys (e/r) to select “AUDIO 1” (audio input jack to be used). CHARGE ENHANCER STEREO TUNED SLEEP MUTE OUT VOL. ECO Audio••AUDIO 1 Video device 6 OPTICAL O O OPTICAL AUDIO 1 1 2 ADAPTIVE DRC VIRTUAL Press OPTION. This completes the necessary settings. (TV) AUDIO 1 (OPTICAL) jack POP-UP/MENU Use the cursor keys (q/w) to select “Audio In” and press ENTER. CHARGE Video output (composite video) AV 2 (VIDEO) jack HOME PRESET Necessary setting The unit (rear) Cursor keys ENTER OPTION ENTER If you select “AV 2” as the input source by pressing INPUT, the video/audio played back on the video device will be output from the unit. Audio output (digital optical) After connecting external devices (such as a TV and playback devices) and power cable of the unit, turn on the unit. Press INPUT to select “AV 2” (video input jack to be used) as the input source. 21 En Connecting audio devices (such as CD players) Connecting to the jack on the front panel Connect audio devices such as CD players and MD players to the unit. Depending on the audio output jacks available on your audio device, choose one of the following connections. Use the AUX jack on the front panel to temporarily connect devices such as portable audio players to the unit. Audio output jacks on audio device Before making a connection, stop playback on the device and turn down the volume on the unit. Audio input jacks on the unit Digital optical AUDIO 1 (OPTICAL) Digital coaxial AUDIO 2 (COAXIAL) AV 1 (COAXIAL) Analog stereo AV 2–3 (AUDIO) BD DVD CD TV RADIO AUX INPUT TONE CONTROL PROGRAM USB STRAIGHT AUDIO The unit (rear) The unit (front) O O OPTICAL OPTICAL C C COAXIAL COAXIAL L L L Audio device Portable audio player L R If you select “AUX” as the input source by pressing INPUT, the audio played back on the device will be output from the unit. R R AV 1–3 jacks AUDIO 1–2 jacks R Note Audio output (either digital optical, digital coaxial, or analog stereo) ▪ You need to prepare the audio cable that matches the output jacks on your device. ▪ For details on how to connect a USB storage device, see “Connecting a USB storage device” (p.44). If you select AV 1-3 or AUDIO 1-2 as the input source by pressing INPUT, the audio played back on the audio device will be output from the unit. 22 En 4 Connecting the FM/AM antennas 5 Connecting the power cable Connect the supplied FM/AM antennas to the unit. Warning Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface. (Taiwan, Brazil and General models only) Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall outlet. Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create a potential fire hazard. FM antenna AM antenna Before connecting the power cable Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110– 120/220–240 V, 50/60 Hz. The unit (rear) VOLTAGE SELECTOR VOLTAGE SELECTOR 110V– 120V 220V– 240V The unit (rear) Assembling and connecting the AM antenna After all the connections are complete, plug in the power cable. The unit (rear) To an AC wall outlet Hold down Insert Release Note ▪ Unwind only the length of cable needed from the AM antenna unit. ▪ The wires of the AM antenna have no polarity. 23 En 6 Selecting an on-screen menu language Select the desired on-screen menu language. 1 2 6 Press z (receiver power) to turn on the unit. Note The information on the front display is provided in English only. Turn on the TV and switch the TV input to display video from the unit (HDMI OUT jack). Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 3 4 Press SETUP. Use the cursor keys to select “Language” and press ENTER. Setup Speaker HDMI Sound ECO Function Language RETURN 5 To exit from the menu, press SETUP. Back Use the cursor keys to select the desired language. Language English 日本語 Français Deutsch Español Русский Italiano 中文 24 En 7 Optimizing the speaker settings automatically (YPAO) The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. 4 Place the YPAO microphone at your listening position and connect it to the YPAO MIC jack on the front panel. Note Note ▪ When you use the front 5.1-channel speaker (Virtual CINEMA FRONT) configuration (p.13), set “Virtual CINEMA FRONT” (p.55) in the “Setup” menu to “On” beforehand. Place the YPAO microphone at your listening position (same height as your ears). We recommend the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the microphone. ▪ Please note the following when using YPAO. The unit (front) – Use YPAO after connecting a TV and speakers to the unit. – During the measuring process, test tones are output at high volume. Ensure that the test tones do not frighten small children. – During the measuring process, you cannot adjust the volume. – During the measuring process, keep the room as quiet as possible. – Do not connect headphones. 1 – Do not stand between the speakers and the YPAO microphone during the measurement process (about 3 minutes). 1 2 9 Press z (receiver power) to turn on the unit. Turn on the TV and switch the TV input to display video from the unit (HDMI OUT jack). 2 3 4 5 Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 3 Ear height Turn on the subwoofer and set the volume to half. If the crossover frequency is adjustable, set it to maximum. VOLUME CROSSOVER/ HIGH CUT The following screen appears on the TV. Auto Setup 9 Start Exit MIN MAX MIN MAX 25 En 5 7 To start the measurement, use the cursor keys to select “Start” and press ENTER. Use the cursor keys (e/r) to select “SAVE” and press ENTER. Auto Setup The measurement will start in 10 seconds. Press ENTER to start the measurement immediately. Start Exit < SAVE > Note To stop the measurement temporarily, press RETURN and follow the procedure in “Error messages” (p.27). The following screen appears on the TV when the measurement finishes. The adjusted speaker settings are applied. Auto Setup Meaurement Finished Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / +10.0 dB ENTER OK 1 2 3 4 Note To finish the measurement without saving the result, select “CANCEL”. 8 Disconnect the YPAO microphone from the unit. This completes optimization of the speaker settings. 1 The number of speakers (front side/rear side/subwoofer) 2 Speaker distance (nearest/farthest) 3 Adjustment range of speaker output level 4 Warning message (if available) Notice ▪ The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be exposed to direct sunlight or high temperatures (such as on top of AV equipment). Note ▪ If any error message (such as E-1) or warning message (such as W-1) appears, see “Error messages” (p.27) or “Warning messages” (p.28). ▪ A speaker with a problem is indicated by blinking of the speaker indicators in the front display. ▪ If multiple warnings are given (when operating with the front display), use the cursor keys (q/w) to check the other warning messages. 6 Confirm the results displayed on the screen and press ENTER. 26 En Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message Cause E-1:No Front SP Front speakers are not detected. (E-1:NO FRNT SP) Auto Setup ERROR E-9 : User Cancel E-2:No Sur. SP Error message (E-2:NO SUR SP) < RETRY > One of the surround speakers cannot be detected. (E-5:NOISY) E-7:No MIC TV screen (E-7:NO MIC) ENHANCER STEREO TUNED CHARGE OUT Keep the room quiet and retry YPAO. If you select “PROCEED”, YPAO takes the measurement again and ignores any noise detected. The YPAO microphone has been removed. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. SLEEP MUTE VOL. ECO E-5:NOISY ADAPTIVE DRC VIRTUAL E-8:No Signal Front display (E-8:NO SIGNAL) n Procedure to handle errors 1 2 E-9:User Cancel (E-9:CANCEL) Check the content of error message and press ENTER. E-10:Internal Err. (E-10:INTERNAL) Use the cursor keys (e/r) to select the desired operation. To exit the YPAO measurement: 1 2 3 Use the cursor keys (q/w) to select “Exit” and press ENTER. Disconnect the YPAO microphone from the unit. Select “RETRY” and press ENTER. To proceed with the current YPAO measurement (for E-5 and E-9 only): 1 An internal error has occurred. Texts in parentheses denote indicators on the front display. To retry the YPAO measurement from beginning: 1 The measurement has been Retry or exit YPAO as necessary. canceled. Note Select “EXIT” and press ENTER. Select “PROCEED” and press ENTER. 27 En Exit YPAO, turn off the unit, and then check the speaker connections. The noise is too loud. 2% E-5:Noisy Remedy Exit YPAO, and turn off and on the unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. Warning messages If a warning message is displayed after the measurement, you can still save the measurement results by following on-screen instructions. Warning message Cause Check the cable connections (+/-) of the problem speaker. However, we recommend you perform YPAO again in order to use the unit with the optimal speaker settings. If the speaker is connected incorrectly: Auto Setup Meaurement Finished Result W-1:Out of Phase 3 / 2 / 0.1 ch 3.0 / 10.5 m (W-1:PHASE) -3.0 / +10.0 dB ENTER OK W-1 : Out of Phase A speaker cable may be connected with the reverse polarity (+/-). Warning message Problem speaker (blinks) ENHANCER STEREO TUNED CHARGE OUT W-2:Over Distance (W-2:DISTANCE) SLEEP MUTE VOL. ECO W-1:PHASE ADAPTIVE DRC VIRTUAL Front display n Procedure to handle warnings W-3:Level Error (W-3:LEVEL) Check the content of warning message and press ENTER. Note Texts in parentheses denote indicators on the front display. 1 If the speaker is connected correctly: Select “SAVE” and press ENTER. Select “CANCEL” and press ENTER. Disconnect the YPAO microphone from the unit. 28 En Exit YPAO, turn off the unit, and place the problem speaker within 24 m (80 ft) of the listening position. Check the usage environment and cable connections (+/-) of each speaker, and the volume of the subwoofer. If there is There are significant volume any problem, exit YPAO, turn off the unit, differences between the and then reconnect speaker cable or speakers. correct the speaker positions. We recommend using the same speakers or speakers with specifications that are as similar as possible. To save the measurement results: To discard the measurement result: 3 A speaker is placed more than 24 m (80 ft) from the listening position. Use the cursor keys (e/r) to select the desired operation. 1 Turn off the unit, reconnect the speaker cable. Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. In this case, you can ignore the message. TV screen 1 2 Remedy PLAYBACK Basic playback procedure Enjoying playback 1 2 3 Refer to the instruction manual for the external device. Turn on the external devices (such as a TV or BD/DVD player) connected to the unit. For details on the following operations, see the corresponding pages. ▪ “Listening to FM/AM radio” (p.37) ▪ “Playing back music stored on a Bluetooth® device” (p.42) Use the input selection keys to select an input source. ▪ “Playing back music stored on a USB storage device (Except for USA, Canada, Australia models)” (p.44) SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM PROGRAM FM/AM 4 Input selection keys USB INPUT VOLUME BLUETOOTH FM/AM RETURN TOP MENU RED USB OPTION INPUT ENTER DISPLAY HOME GREEN YELLOW VOLUME VOLUME ▪ To mute the audio output, press MUTE. Press MUTE again to unmute. BLUETOOTH ▪ To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL on the front panel (p.48). POP-UP/MENU BLUE MEMORY TUNING TUNING PRESET Press VOLUME to adjust the volume. Note MUTE SETUP Start playback on the external device or select a radio station. MUTE MUTE 29 En Switching information on the front display 1 Currently input source AV Press INFO repeatedly to select between the various display items. ENHANCER STEREO TUNED CHARGE AUDIO AUX Input (input source name), DSP Program (sound mode name), Audio Decoder (decoder name*) Bluetooth SLEEP MUTE OUT Item HDMI VOL. ECO ADAPTIVE DRC VIRTUAL Audio Decoder USB Item name Frequency (frequency), DSP Program (sound mode name), Audio Decoder (decoder name*) About 3 seconds after a display item is selected, its corresponding information appears. ENHANCER STEREO TUNED CHARGE OUT TUNER SLEEP MUTE VOL. ECO †‡Pro Logic Song (song title), Artist (artist name), Album (album name), DSP Program (sound mode name), Audio Decoder (decoder name*) (U.K. and Europe models only) Radio Data System data is also available when the unit is tuned into a Radio Data System broadcasting station (p.41). ADAPTIVE DRC VIRTUAL * The name of the audio decoder currently activated is displayed. If no audio decoder is activated, “Decoder Off” appears. Information Note Available items vary depending on the selected input source. The displayed item can also be applied separately to each input source. 30 En Selecting the input source and favorite settings with one touch (SCENE) The SCENE function allows you to select the assigned input source, sound program, and Compressed Music Enhancer on/off with just one touch. Registering a scene 1 Selecting a registered scene 1 ▪ Select an input source (p.29) Press SCENE. ▪ Select a sound program (p.32) or straight decode (p.35) The input source and settings registered to the corresponding scene are selected. The unit turns on automatically when it is in standby mode. ▪ Enable/disable Compressed Music Enhancer (p.36) 2 SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Perform the following operations to prepare the settings you want to assign to a scene. Hold down the desired SCENE key until “SET Complete” appears on the front display. PROGRAM CHARGE ENHANCER STEREO TUNED SLEEP MUTE FM/AM OUT USB INPUT SLEEP VOLUME SET Complete SCENE MUTE SETUP BD DVD OPTION TV CD RADIO ENHANCER BASS SCENE ENTER RETURN TOP MENU RED STRAIGHT DISPLAY HOME GREEN YELLOW POP-UP/MENU BLUE PROGRAM MEMORY TUNING TUNING PRESET By default, the following settings are registered for each scene. SCENE Input HDMI1 VOL. ECO BLUETOOTH AUDIO1 AUDIO2 TUNER Sound program MOVIE (Sci-Fi) STRAIGHT STRAIGHT STEREO (5ch Stereo) Compressed Music Enhancer Off On Off On SCENE link playback On On Off Off Note The SCENE link playback function allows you to automatically turn on the TV or start playback of an external device connected to the unit via HDMI, in conjunction with a scene selection. To enable SCENE link playback, set “SCENE” (p.58) in the “Setup” menu to “On”. 31 En ADAPTIVE DRC VIRTUAL Selecting the sound mode I want to enjoy listening to compressed music. The unit is equipped with a variety of sound programs and surround decoders that allow you to enjoy playback sources with your favorite sound mode (such as sound field effect or stereo playback). • Enable Compressed Music Enhancer by pressing ENHANCER (p.36). This mode lets you enjoy compressed music stored on a Bluetooth device or USB storage device with additional depth and breadth (p.36). SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Note PROGRAM ▪ The sound mode can be applied separately to each input source. FM/AM USB INPUT VOLUME SLEEP MUTE SCENE BLUETOOTH SETUP OPTION BD DVD TV CD RADIO ENHANCER BASS ▪ When you play back audio signals with a sampling rate of higher than 96 kHz, the straight decode mode (p.35) is automatically selected. ▪ You can check which speakers are currently outputting sound by looking at the speaker indicators on the unit’s front panel (p.8). ENTER RETURN TOP MENU RED DISPLAY HOME GREEN YELLOW BLUE MEMORY TUNING STRAIGHT POP-UP/MENU PROGRAM TUNING PRESET STRAIGHT ENHANCER BASS PROGRAM I want to enjoy viewing video sources such as movies, TV programs, or games. • Select a sound program suitable for each video source by pressing PROGRAM repeatedly (p.33). I want to enjoy listening to music sources or stereo playback. • Select a sound program suitable for music or stereo playback by pressing PROGRAM repeatedly (p.34). I want to enjoy multichannel playback from 2-channel sources. • Select a surround decoder in the “Option” menu (p.47). I want to enjoy unprocessed sounds in original channels. • Switch to the straight decode mode by pressing STRAIGHT (p.35). I want to enjoy enhanced bass sounds. • Enable Extra Bass by pressing BASS (p.36). 32 En Enjoying sound field effects (CINEMA DSP) Drama This program features stable reverberations that match a wide range of movie genres, from serious dramas to musicals and comedies. The reverberations are modest, but suitably stereophonic. The sound effects and background music are reproduced with a gentle echo that does not impinge on the articulation of the dialogue. You’ll never get tired listening for long periods. Mono Movie This program reproduces monaural video sources, such as classic movies, in an atmosphere of a good old movie theater. The program creates a pleasant space with depth, by adding breadth and the appropriate reverberation to the original audio. Sports This program allows listeners to enjoy the rich vividness of sport broadcasts and light entertainment programs. In sports broadcasts, the commentators’ voices are positioned clearly at the center, while the atmosphere inside the stadium is realistically conveyed by the peripheral delivery of the sounds of the fans in a suitable space. Action Game This program is suitable for action games, such as car racing and fighting games. The reality of, and emphasis on, various effects makes the player feel like they are right in the middle of the action, allowing for greater concentration. Use this program in combination with Compressed Music Enhancer for a more dynamic and strong sound field. Roleplaying Game This program is suitable for role-playing and adventure games. This program adds depth to the sound field for natural and realistic reproduction of background music, special effects, and dialogue from a wide variety of scenes. Use this program in combination with Compressed Music Enhancer for a clearer and more spatial sound field. The unit is equipped with a variety of sound programs that utilize Yamaha’s original DSP technology (CINEMA DSP). It allows you to easily create sound fields like actual movie theaters or concert halls in your room. Sound program category “CINEMA DSP” lights up CHARGE ENHANCER STEREO TUNED OUT SLEEP MUTE VOL. ECO Sci-Fi ADAPTIVE DRC VIRTUAL Sound program Note You can adjust the sound field effect level in “DSP Level (DSP Level)” (p.48) in the “Option” menu. n Sound programs suitable for movies (MOVIE) The following sound programs are optimized for viewing video sources, such as movies, TV programs, and games. Standard This program creates a sound field that emphasizes the surround feeling without disturbing the original acoustic positioning of multichannel audio, such as Dolby Digital and DTS. Its design is based on the concept of the ideal movie theater, in which the audience is surrounded by beautiful reverberations from the left, right, and rear. Spectacle This program delivers the scale and grandeur of spectacular movie productions. It delivers an expansive sound space to match the cinemascope wide-screen, and boasts a broad dynamic range, providing everything from small delicate sounds to powerful loud booms. Sci-Fi This program clearly reproduces the finely elaborated sound design of the latest Sci-Fi and SFX movies. You can enjoy a variety of cinematographically created virtual spaces reproduced with clear separation between dialogue, sound effects, and background music. Adventure This program is ideal for reproducing the sound design of action and adventure movies precisely. The sound field restrains reverberations, but puts emphasis on reproducing a sensation of expansiveness on both sides, powerful space expanded widely to the left and right. The restrained depth creates a clear and powerful space, while also maintaining the articulation of the sounds and the separation of the channels. 33 En n Sound programs suitable for music (MUSIC) n Sound programs suitable for stereo playback (STEREO) The following sound programs are optimized for listening to music sources. You can select stereo playback. Hall in Munich This program simulates a Munich concert hall with approximately 2,500 seats that uses stylish wood for the interior finishing. Fine, beautiful reverberations spread richly, creating a calming atmosphere. The listener’s virtual seat is at the center left of the arena. Hall in Vienna This program simulates a 1700-seat, middle-sized concert hall with a shoebox shape that is traditional in Vienna. Pillars and ornate carvings create extremely complex reverberations from all around the audience, producing a very full, rich sound. Chamber This program creates a relatively wide space with a high ceiling, like an audience hall in a palace. It offers pleasant reverberations that are suitable for courtly music and chamber music. Cellar Club This program simulates an intimate concert venue with a low ceiling and homey atmosphere. A realistic, live sound field delivers powerful sounds that make you feel as if you are sitting in the front row in front of a small stage. The Roxy Theatre This program creates the sound field of a 460-seat rock music concert venue in Los Angeles. The listener’s virtual seat is at the center left of the hall. The Bottom Line This program creates the sound field at stage front in The Bottom Line, a famous New York jazz club once. The floor can seat 300 people to the left and right in a sound field offering real and vibrant sound. Music Video 2ch Stereo Use this program to mix down multichannel sources to 2 channels. When multichannel signals are input, they are down mixed to 2 channels and output from the front speakers (this program does not utilize CINEMA DSP). 5ch Stereo Use this program to output sound from all speakers. When you play back multichannel sources, the unit mixes down the source to 2 channels, and then outputs the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties. n Enjoying sound field effects without surround speakers (Virtual CINEMA DSP) If you select one of the sound programs (except 2ch Stereo and 5ch Stereo) when no surround speakers are connected, the unit automatically creates the surround sound field using the front-side speakers. n Enjoying surround sound with 5 speakers placed in front (Virtual CINEMA FRONT) You can enjoy the surround sound even when the surround speakers are placed in front. This program allows you to enjoy videos of pop, rock, and jazz concerts, as if you were there yourself. Immerse yourself in the hot concert atmosphere thanks to the vividness of the singers and solos on stage, a presence sound field that emphasizes the beat of rhythm instruments, and a surround sound field that reproduces the space of a big live hall. n Enjoying surround sound with headphones (SILENT CINEMA) You can enjoy surround or sound field effects, like a multichannel speaker system, with stereo headphones by connecting the headphones to the PHONES jack and selecting a sound program or a surround decoder. 34 En n Playing back 2-channel sources in multichannel Enjoying unprocessed playback (surround decoder) You can play back input sources without any sound field effect processing. The surround decoder enables unprocessed multichannel playback from 2-channel sources. When a multichannel source is input, it works the same way as the straight decode mode. n Playing back in original channels (straight decode) When the straight decode mode is enabled, the unit produces stereo sound from the front speakers for 2-channel sources such as CDs, and produces unprocessed multichannel sounds for multichannel sources. 1 For details on each decoder see “Glossary” (p.76). 1 Press STRAIGHT. Press PROGRAM repeatedly to select a surround decoder. The previously selected surround decoder is selected. You can change the surround decoder in “Sur.Decode” (p.47) in the “Option” menu. Each time you press the key, the straight decode mode is enabled or disabled. SLEEP SCENE BD DVD CHARGE ENHANCER STEREO TUNED OUT SLEEP MUTE TV STRAIGHT VOL. ECO STRAIGHT CD RADIO ENHANCER BASS PROGRAM ADAPTIVE DRC VIRTUAL FM/AM USB INPUT VOLUME SLEEP MUTE SCENE BLUETOOTH SETUP BD DVD OPTION TV CD RADIO ENHANCER BASS ENTER RETURN TOP MENU RED STRAIGHT DISPLAY POP-UP/MENU HOME GREEN YELLOW BLUE PROGRAM MEMORY TUNING PROGRAM TUNING PRESET “SUR. DECODE” appears ENHANCER STEREO TUNED CHARGE OUT SLEEP MUTE VOL. ECO †‡Pro Logic ADAPTIVE DRC VIRTUAL bPro Logic Uses the Dolby Pro Logic decoder suitable for all sources. bPLII Movie Uses the Dolby Pro Logic II decoder suitable for movies. bPLII Music Uses the Dolby Pro Logic II decoder suitable for music. bPLII Game Uses the Dolby Pro Logic II decoder suitable for games. Neo:6 Cinema Uses the DTS Neo: 6 decoder suitable for movies. Neo:6 Music Uses the DTS Neo: 6 decoder suitable for music. Note You can adjust the surround decoder parameters in “DSP Parameter” (p.59) in the “Setup” menu. 35 En Enhancing the bass (Extra Bass) Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer) Extra Bass allows you to enjoy enhanced bass sounds, regardless of the size of the front speakers and the presence or absence of the subwoofer. 1 Press BASS. Each time you press the key, Extra Bass is enabled or disabled. Compressed Music Enhancer adds depth and breadth to the sound, allowing you to enjoy a dynamic sound close to the original sound before it was compressed. This function can be used along with any other sound modes. Note You can also use “Extra Bass” (p.55) in the “Setup” menu to enable/disable Extra Bass. 1 Press ENHANCER. Each time you press the key, Compressed Music Enhancer is enabled or disabled. “ENHANCER” lights up CHARGE ENHANCER STEREO TUNED OUT SLEEP MUTE VOL. ECO Enhancer On ADAPTIVE DRC VIRTUAL Note ▪ Compressed Music Enhancer does not work on the following audio sources. – Signals whose sampling rate is over 48 kHz – High-definition streaming audio ▪ You can also use “Enhancer (Enhancer)” (p.48) in the “Option” menu to enable/disable Compressed Music Enhancer. 36 En Listening to FM/AM radio You can tune into a radio station by specifying its frequency or selecting from registered radio stations. 4 5 Note ▪ The radio frequencies differ depending on the country or region where the unit is being used. The explanation of this section uses a display with frequencies used in U.K. and Europe models. ▪ If you cannot obtain good reception on the radio, adjust the direction of the FM/AM antennas. Press STRAIGHT to select “FM100/AM10”. Press z (power) to set the unit to standby mode and turn it on again. Selecting a frequency for reception Setting the frequency steps 1 (Asia, Taiwan, Brazil and General models only) At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz for AM. Depending on your country or region, set the frequency steps to 100 kHz for FM and 10 kHz for AM. Press FM/AM to select a band. “TUNER” is selected as the input source and then the frequency currently selected is displayed. CHARGE OUT 1 2 ECO When holding down STRAIGHT on the front panel, press z (power). z (power) 3 STRAIGHT Press PROGRAM repeatedly to select “TU”. CHARGE OUT ECO ENHANCER STEREO TUNED SLEEP MUTE VOL. TU••••FM50/AM9 SLEEP MUTE VOL. FM 87.50MHz Set the unit to standby mode. PROGRAM ENHANCER STEREO TUNED ADAPTIVE DRC VIRTUAL 37 En ADAPTIVE DRC VIRTUAL 2 Registering favorite radio stations (presets) Press TUNING repeatedly to set a frequency. You can register up to 40 radio stations as presets. Once you have registered stations, you can easily tune into them by selecting their preset numbers. Hold down the key for about a second to search stations automatically. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS n Registering radio stations automatically (Auto Preset) PROGRAM FM/AM RED USB INPUT VOLUME GREEN YELLOW LO Automatically register FM radio stations with strong signals (up to 40 stations). BLUE BLUETOOTH TUNING MEMORY MUTE SETUP Note OPTION TUNING ENTER RETURN TUNING ▪ To register AM radio stations, follow “Registering a radio station manually” (p.39). DISPLAY TOP MENU HOME ▪ (U.K. and Europe models only) Only Radio Data System broadcasting stations are registered automatically by the Auto Preset function. POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY TUNING TUNING PRESET CHARGE OUT ECO ENHANCER STEREO TUNED 1 2 3 SLEEP MUTE VOL. FM 98.50MHz ADAPTIVE DRC VIRTUAL “TUNED” lights up when a signal is received from a radio station. “STEREO” also lights up when a stereo signal is received. Press FM/AM to select “TUNER” as the input source. Press OPTION. Use the cursor keys to select “Preset” and press ENTER. CHARGE OUT Preset Note ▪ You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio reception by selecting “FM Mode” (p.47) in the “Option” menu. When the signal reception for an FM radio station is unstable, switching to monaural may improve it. ▪ You can watch videos input from external devices while listening to radio by selecting the video input jack in “Video Out (Video Out)” (p.50) in the “Option” menu. 38 En ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO ADAPTIVE DRC VIRTUAL 4 n Registering a radio station manually To start the Auto Preset process, press ENTER. Select a radio station manually and register it to a preset number. “SEARCH” appears during Auto Preset ENHANCER STEREO TUNED CHARGE OUT 1 SLEEP MUTE VOL. ECO 01:FM 87.50MHz ADAPTIVE DRC VIRTUAL 2 Preset number from which to start the registration Follow “Selecting a frequency for reception” (p.37) to tune into the desired radio station. Hold down MEMORY for a few seconds. The first time that you do register a station, the selected radio station will be registered to the preset number “01”. Thereafter, each radio station you select will be registered to the next empty (unused) preset number after the most recently registered number. Note ▪ To specify the preset number from which to start the registration, press cursor keys (e/r) or PRESET to select a preset number. ▪ To cancel the Auto Preset process, press RETURN. When the Auto Preset process finishes, “FINISH” appears and the “Option” menu closes automatically. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM CHARGE ENHANCER STEREO TUNED SLEEP MUTE FM/AM OUT VOL. ECO Auto Preset RED USB INPUT VOLUME ADAPTIVE DRC VIRTUAL GREEN YELLOW LO BLUE BLUETOOTH MEMORY MEMORY MUTE SETUP OPTION TUNING ENTER RETURN TUNING DISPLAY TOP MENU HOME POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY TUNING TUNING PRESET ENHANCER STEREO TUNED CHARGE OUT SLEEP MUTE VOL. ECO 01:FM 98.50MHz ADAPTIVE DRC VIRTUAL Preset number Note To specify the preset number for registering, press PRESET to select a preset number, and then press MEMORY. CHARGE ENHANCER STEREO TUNED OUT SLEEP MUTE VOL. ECO 02:Empty ADAPTIVE DRC VIRTUAL “Empty” (not in use) or the frequency currently registered 39 En n Selecting a preset station n Clearing preset stations Tune into a registered radio station by selecting its preset number. Clear radio stations registered to the preset numbers. 1 2 1 2 3 Press FM/AM to select “TUNER” as the input source. Press PRESET repeatedly to select the desired radio station. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS Press FM/AM to select “TUNER” as the input source. Press OPTION. Use the cursor keys to select “Preset” and press ENTER. PROGRAM CHARGE RED USB VOLUME GREEN YELLOW LO TUNING TUNING DISPLAY TOP MENU HOME POP-UP/MENU PRESET RED 4 5 OPTION ENTER GREEN YELLOW BLUE PRESET MEMORY TUNING ADAPTIVE DRC VIRTUAL Preset MEMORY MUTE SETUP TUNING PRESET Use the cursor keys (q/w) to select “CLEAR”. Use the cursor keys (e/r) to select a preset station to be cleared and press ENTER. CHARGE ENHANCER STEREO TUNED OUT OUT ENHANCER STEREO TUNED 01:FM 98.50MHz SLEEP MUTE VOL. ECO 01:FM 98.50MHz SLEEP MUTE VOL. ECO CHARGE SLEEP MUTE VOL. ECO BLUE BLUETOOTH RETURN ENHANCER STEREO TUNED OUT FM/AM INPUT ADAPTIVE DRC VIRTUAL ADAPTIVE DRC VIRTUAL Preset station to be cleared If the preset station is cleared, “Cleared” appears and then the next in-use preset number is displayed. Note “No Presets” appears when no radio stations are registered. CHARGE ENHANCER STEREO TUNED OUT 01:Cleared 6 7 40 En SLEEP MUTE VOL. ECO ADAPTIVE DRC VIRTUAL Repeat step 5 until all desired preset stations are cleared. To exit from the menu, press OPTION. Radio Data System tuning n Receiving traffic information automatically (U.K. and Europe models only) When “TUNER” is selected as the input source, the unit automatically receives traffic information. To enable this function, follow the procedure below to set the traffic information station. Radio Data System is a data transmission system used by FM stations in many countries. The unit can receive various types of Radio Data System data, such as “Program Service”, “Program Type”, “Radio Text” and “Clock Time”, when it is tuned into a Radio Data System broadcasting station. 1 2 n Displaying the Radio Data System information 1 Use the cursor keys to select “Traffic Program” (TrafficProgram) and press ENTER. The traffic information station search will start in 5 seconds. Press ENTER again to start the search immediately. Tune into the desired Radio Data System broadcasting station. Note Note We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations (p.38). 2 When “TUNER” is selected as the input source, press OPTION. ▪ To search upward/downward from the current frequency, press the cursor keys (q/w) while “READY” is displayed. ▪ To cancel the search, press RETURN. Press INFO. ▪ Texts in parentheses denote indicators on the front display. Each time you press the key, the displayed item changes. ENHANCER STEREO TUNED CHARGE The following screen appears for about 3 seconds when the search finishes. SLEEP MUTE OUT VOL. ECO ADAPTIVE DRC VIRTUAL Program Type CHARGE Note “TP Not Found” appears for about 3 seconds when no traffic information stations are found. VOL. ECO CLASSICS ADAPTIVE DRC VIRTUAL Information Program service name Program Type Current program type Radio Text Information on the current program Clock Time Current time DSP Program Sound mode name Audio Decoder Decoder name Frequency Frequency ADAPTIVE DRC VIRTUAL Traffic information station (frequency) SLEEP MUTE OUT Program Service VOL. TP FM101.30MHz About 3 seconds later, the corresponding information for the displayed item appears. ENHANCER STEREO TUNED SLEEP MUTE ECO Item name CHARGE ENHANCER STEREO TUNED OUT Note “Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio station does not provide the Radio Data System service. 41 En Playing back music stored on a Bluetooth® device You can play back music files stored on a Bluetooth device on the unit. 4 Please also refer to the owner’s manual of your Bluetooth device. Note After pairing has been completed and the unit is connected to the Bluetooth device, “Connected” appears on the front display. While a Bluetooth connection is established, the Bluetooth indicators light up. ▪ The Bluetooth device must support A2DP. ▪ You cannot play back video files stored on a Bluetooth device on the unit. Connecting a Bluetooth® device (pairing) CHARGE SLEEP MUTE VOL. ECO Connected ADAPTIVE DRC VIRTUAL SL L C R SW SR Note ▪ If you are prompted to input a passkey during a pairing procedure, input the numerals “0000”. ▪ Complete a pairing procedure within 30 seconds. ▪ If no Bluetooth devices are found, “Not found” appears. Press BLUETOOTH to select “Bluetooth” as the input source. Hold down MEMORY on the front panel or the remote control for more than 3 seconds. “Searching…” appears on the front display. Note ▪ You can also use the “Option” menu to pair a Bluetooth device. Press OPTION, and then use the cursor keys to select “Pairing”. ▪ If another Bluetooth device is already connected, disconnect the Bluetooth connection before you perform a pairing operation. ▪ To cancel pairing, press MEMORY. 3 ENHANCER STEREO TUNED OUT When connecting a Bluetooth device to the unit for the first time, the pairing operation is required to perform. Pairing is an operation that registers the Bluetooth devices with each other beforehand. Once pairing has been completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected. 1 2 From the Bluetooth device list on your device, select “******* Yamaha” (*******: model name of the unit). Turn on the Bluetooth function on your device. 42 En Playback of Bluetooth® device contents Connect a paired Bluetooth device and start playback. Check the following beforehand: • Pairing has been completed. • Bluetooth function on the Bluetooth device is turned on. 1 Operate the Bluetooth device to establish a Bluetooth connection. Select the model name of the unit from the Bluetooth device list on your device. When a connection is established, the unit’s input source automatically switches to “Bluetooth”. Note ▪ If you do not want the input source to switch automatically when a connection is established, set “Input Interlock” (p.47) to “Off” in the “Option” menu. ▪ You can operate the unit to search and connect the Bluetooth device (only the most recently connected device). In that case, follow one of the procedures below. – Switch the input source to “Bluetooth”. – Press ENTER while the input source is “Bluetooth”. Otherwise, press OPTION and use the cursor keys to select “Connect”. ▪ If you cannot connect the device, please perform pairing again. 2 Operate the Bluetooth device to play back music. Note You cannot operate the unit to select or play back music, or display informations such as song names. Disconnecting a Bluetooth® connection Follow one of the procedures below to disconnect a Bluetooth connection. • Perform the disconnect operation on the Bluetooth device. • Press ENTER. • Press OPTION and use the cursor keys to select “Disconnect”. • Switch the unit's input source to other than “Bluetooth”. 43 En Playing back music stored on a USB storage device (Except for USA, Canada, Australia models) You can play back music files stored on a USB storage device on the unit. Playback of USB storage device contents Note For details on playable USB devices, see “Supported devices and file formats” (p.78). Follow the procedure below to operate the USB storage device contents and start playback. Connecting a USB storage device You can control the USB memory device with the menu displayed on the TV screen. 1 Note ▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI. Connect the USB storage device to the USB jack. ▪ “_” (underscore) will be displayed for characters not supported by the unit. The unit (front) 1 RADIO AUX Press USB to select “USB” as the input source. The browse screen (p.45) is displayed on the TV. USB STRAIGHT Note AUDIO If playback is ongoing on your USB storage device, the playback screen is displayed. 2 Use the cursor keys to select an item and press ENTER. If a song is selected, playback starts and the playback screen (p.45) is displayed. Note USB storage device ▪ To return to the previous screen, press RETURN. ▪ To switch the screen mode browse/playback/off, press DISPLAY. ▪ Files not supported by the unit cannot be selected. Note ▪ If the USB storage device contains many files, it may take time to load them. In this case, “Loading…” appears in the front display. ▪ Stop playback of the USB storage device before disconnect it from the USB jack. ▪ Connect a USB storage device directly to the USB jack of the unit. Do not use extension cables. 44 En n Playback screen n Browse screen 4 1 2 Blues Classical Electronica Jazz Pop Rock Soundtrack Speaking 1 USB USB - Top Artist Album 5 2 Song 2 : 30 5 : 30 1/9999 3 1 List name 2 Contents list 1 Displays the list of USB storage device contents. Use the cursor keys to select an item and press ENTER to confirm the selection. 3 4 2 Playback information Displays the artist name, album name, song title, and elapsed time. Item number/total Status indicators Use the following remote control keys to control playback. Display the current repeat/random settings (p.46) and playback status (such as play/pause). 5 Status indicators Display the current repeat/random settings (p.46) and playback status (such as play/pause). SLEEP SCENE BD DVD Operation menu TV STRAIGHT CD RADIO ENHANCER BASS PROGRAM Press the cursor key (r) and then use the cursor keys (q/w) to select an item. Press ENTER to confirm the selection. FM/AM RED USB INPUT VOLUME GREEN YELLOW LO BLUE BLUETOOTH MEMORY MUTE SETUP Icon OPTION Function TUNING ENTER RETURN Moves 10 pages backward. TOP MENU TUNING External device operation keys DISPLAY HOME POP-UP/MENU PRESET RED GREEN YELLOW BLUE MEMORY Moves to the previous page of the list. TUNING TUNING PRESET Moves to the next page of the list. Moves 10 pages forward. External device operation keys Moves to the playback screen. Note A content selected by the cursor is displayed on the front display. Function a Resumes playback from pause or starts playback of the previously selected song. s Stops playback. d Stops playback temporarily. f g h j Skips forward/backward. Searches forward/backward (by holding down). Note A content name of a current playback is displayed on the front display. To switch the displayed item, press INFO (p.30). 45 En n Repeat/random settings You can configure the repeat/random settings for playback of USB storage device contents. 1 2 When “USB” is selected as the input source, press OPTION. Use the cursor keys to select “Repeat” (Repeat) and press ENTER. Note ▪ To return to the previous screen during menu operations, press RETURN. ▪ Texts in parentheses denote indicators on the front display. 3 4 Use the cursor keys (e/r) to select a setting. Setting Function Off (Off) Turns off the repeat function. One (One) Plays back the current song repeatedly. “c” appears on the TV screen. All (All) Plays back all songs in the current album (folder) repeatedly. “v” appears on the TV screen. Random (Random) Plays back songs in random order. “x” appears on the TV screen. To exit from the menu, press OPTION. 46 En Configuring playback settings for different playback sources (Option menu) You can configure separate playback settings for different playback sources. This menu is available on the front panel (or on the TV screen), allowing you to easily configure settings during playback. 1 Option menu items Note ▪ Available items vary depending on the selected input source. Press OPTION. ▪ Text in parentheses denotes indicators on the front display. ENHANCER STEREO TUNED CHARGE OUT ▪ Default settings are underlined. SLEEP MUTE VOL. ECO Input Select ADAPTIVE DRC VIRTUAL Front display Option Input Select Item Function Input Select (Input Select) Switches the input source. p.48 Tone Control (Tone Control) Adjusts the level of high-frequency range and lowfrequency range individually. p.48 Program (PRG) Select the sound programs and stereo playback. p.33 Sur.Decode (SrDec) Select which surround decoder is used when Sur.Decode is selected as the program. p.35 Adjusts the sound field effect level. p.48 Sets whether the dynamic range (from maximum to minimum) is automatically adjusted when the volume is adjusted. p.48 Enables/disables Compressed Music Enhancer. p.48 Tone Control DSP/Surround Volume Trim Lipsync Signal Info. Audio In RETURN DSP Level DSP/Surround (DSP Level) (DSP/ Surround) Adaptive DRC (A.DRC) Back TV screen 2 Enhancer (Enhancer) Use the cursor keys to select an item and press ENTER. Input Trim Corrects volume differences between input sources. (In.Trim) Volume Trim (Volume Trim) Subwoofer Trim Fine-adjusts the subwoofer volume. (SW.Trim) Note To return to the previous screen during menu operations, press RETURN. 3 4 Use the cursor keys (e/r) to select a setting. To exit from the menu, press OPTION. p.49 p.49 Lipsync (Lipsync) Enables/disables the “Lipsync” setting in the “Setup” menu. p.49 Signal Info. (Signal Info.) Displays information about the video/audio signal. p.49 Audio In (Audio In) Combines the video jack of the selected input source with an audio jack of others. p.49 Video Out (Video Out) Selects a video to be output with radio sounds. p.50 FM Mode (FM Mode) Switches between “Stereo” and “Mono” for FM radio reception. p.37 Automatically registers FM radio stations with strong signals as presets. p.38 Clear radio stations registered to preset numbers. p.40 Preset (Preset) Auto Preset Clear Preset Traffic Program (TrafficProgram) 47 Page En (U.K. and Europe models only) Automatically searches for a traffic information station. p.41 Item Function n DSP/Surround (DSP/Surround) Page (Except for USA, Canada, Australia models) Repeat (Repeat) Configures the repeat setting for the USB storage device. Configures the sound field program and surround settings. p.46 Pairing (Pairing) Performs a pairing operation between the unit and your Bluetooth device. p.42 Connect/Disconnect (Connect/ Disconnect) Connects/disconnects the Bluetooth device. p.43 Input Interlock (Interlock) Sets whether the input source automatically switches to "Bluetooth" when a Bluetooth connection is established. DSP Level (DSP Level) Adjusts the sound field effect level. Setting range -6 dB to 0 dB to +3 dB (1 dB increments) p.43 Adaptive DRC (A.DRC) n Input Select (Input Select) Switches the input source. Press ENTER to switch to the selected input source. Sets whether the dynamic range (from maximum to minimum) is automatically adjusted when the volume level is adjusted. When it is set to “On”, it is useful for listening to playback at a low volume at night. Choices Settings HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX n Tone Control (Tone Control) On (On) Automatically adjusts the dynamic range. Off (Off) The dynamic range is not automatically adjusted. If “On” is selected, the dynamic range becomes narrow at a low volume and wide at a high volume. Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass) individually. Enhancer (Enhancer) Choices Treble (Treble), Bass (Bass) Enables/disables Compressed Music Enhancer (p.36). Setting range Note -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) ▪ This setting is applied separately to each input source. Note ▪ You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer (p.36). ▪ When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears. ▪ You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or “Bass”, then press PROGRAM to make an adjustment. Settings ▪ If you set an extreme value, sounds may not match those from other channels. Off (Off) Disables Compressed Music Enhancer. On (On) Enables Compressed Music Enhancer. Default Bluetooth, USB, TUNER: On (On) Others: Off (Off) 48 En n Volume Trim (Volume Trim) n Signal Info. (Signal Info.) Fine-adjusts volume difference between input sources or subwoofer volume. Displays information about the video/audio signal. Choices Input Trim (In.Trim) Corrects volume differences between input sources. If you are bothered by volume differences when switching between input sources, use this function to correct it. Format (FORMAT) The number of source channels in the input signal (front/surround/LFE) Channel (CHANNEL) Note This setting is applied separately to each input source. Audio format of the input signal For example, “3/2/0.1” means 3 front channels, 2 surround channels, and LFE. Sampling (SAMPLING) The number of samples per second of the input digital signal Setting range -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) Subwoofer Trim (SW.Trim) Bitrate (BITRATE) The amount of data per second of the input bitstream signal Video In (VIDEO IN) Type and resolution of the input digital signal Video Out (VIDEO OUT) Type and resolution of the output digital signal Note Fine-adjusts the subwoofer volume. To switch the information on the front display, press the cursor keys (q/w) repeatedly. Setting range n Audio In (Audio In) -6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments) n Lipsync (Lipsync) Combines the video jack of the selected input source with an audio jack of others. For example, use this function in the following cases. Enables/disables the adjustment configured in “Lipsync” (p.59) in the “Setup” menu. • Connecting a playback device that supports HDMI video output, but not HDMI audio output Note This setting is applied separately to each input source. Input sources Settings HDMI 1-4, AUDIO 1-2, AV 1-3 Off (Off) Disables the “Lipsync” adjustment. On (On) Enables the “Lipsync” adjustment. Setup procedure See “Changing the combination of video/audio input jacks” (p.21). 49 En n Video Out (Video Out) Selects a video to be output with the selected audio source. For example, you can watch the video while listening to the radio. Input sources AUDIO, TUNER, USB, Bluetooth, AUX Settings Off (Off) Does not output video. HDMI 1-4, AV 1-3 Outputs video input through the corresponding video input jacks. 50 En CONFIGURATIONS Configuring various functions (Setup Menu) You can configure the unit’s various function with the menu displayed on the TV screen. Note Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out operations while viewing the front display. 1 2 Press SETUP. Use the cursor keys to select a menu and press ENTER. Setup Speaker HDMI Sound ECO Function Language RETURN 3 Back Use the cursor keys to select an item and press ENTER. Speaker Conﬁguration Distance Level Equalizer Test Tone Note To return to the previous screen during menu operations, press RETURN. 4 5 Use the cursor keys (e/r) to select a setting and press ENTER. To exit from the menu, press SETUP. 51 En Setup menu items Menu Item Configuration Speaker Function Selects whether or not a subwoofer is connected. Front Selects the size of the front speakers. p.54 Center Selects whether or not a center speaker is connected and its size. p.54 p.55 Surround Selects whether or not surround speakers are connected and their size. Sets the lower limit of the low-frequency component that can be output from speakers whose size is set to “Small”. p.55 Subwoofer Phase Sets the phase of the subwoofer. p.55 Extra Bass Enables/disables Extra Bass. p.55 Virtual CINEMA FRONT Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. p.55 Sets the distance between each speaker and listening position. p.55 Level Adjusts the volume of each speaker. p.56 Equalizer Adjusts the tone with an equalizer. p.56 Test Tone Enables/disables the test tone output. p.56 HDMI Control Enables/disables HDMI Control. p.57 Audio Output Selects a device to output audio. p.57 TV Audio Input Selects an audio input jack of the unit to be used for TV audio input. p.57 Standby Sync Selects whether to use HDMI control to link the standby behavior of the TV and the unit. p.58 ARC Enables/disables ARC. p.58 SCENE Enables/disables SCENE link playback. p.58 Panorama Enables/disables the broadening effect of the front sound field. p.59 Center Width Adjusts the broadening effect of the center sound field. p.59 Dimension Adjusts the difference in level between the front and surround sound fields. p.59 Center Image Adjusts the center orientation level (broadening effect) of the front sound field. p.59 Select Selects the method to adjust the delay between video and audio output. p.59 Adjustment Adjusts the delay between video and audio output manually. p.60 Dialogue Level Adjusts the volume of dialogue sounds. p.60 Scale Switches the scale of the volume display. p.60 Dynamic Range Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. p.60 Max Volume Sets the limit value of the volume. p.60 Initial Volume Sets the initial volume for when this receiver is turned on. p.60 DSP Parameter Sound p.54 Crossover Distance HDMI Page Subwoofer Lipsync Dialogue Volume 52 En Menu ECO Function Language Item Function Auto Power Standby Set the amount of time for the auto-standby function. Page p.61 ECO Mode Enables/disables the eco mode (power saving mode). p.61 Input Rename Changes the input source name displayed on the front display. p.62 Input Skip Set which input source is skipped when operating the INPUT key. p.63 Dimmer Adjusts the brightness of the front display. p.63 Memory Guard Prevents accidental changes to the settings. p.63 Remote Color Key Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. p.64 Select an on-screen menu language. p.64 53 En Speaker Configures the speaker settings manually. Front Note Selects the size of the front speakers. Default settings are underlined. Settings n Configuration Select this option for small speakers. Small Configures the output characteristics of the speakers. Note Select this option for large speakers. When you configure the speaker size, select “Large” if the woofer diameter of your speaker is 16 cm (6‑1/4”) or larger or “Small” if it is smaller than 16 cm (6‑1/4”). Large “Front” is automatically set to “Large” when “Subwoofer” is set to “None”. Selects whether or not a subwoofer is connected. Center Settings Select this option when a subwoofer is connected. Selects whether or not a center speaker is connected and its size. The subwoofer will produce LFE (low-frequency effect) channel audio and low-frequency components from other channels. Settings Select this option for small speakers. Select this option when no subwoofer is connected. None The front speakers will produce all of the front channel frequency components. Note Subwoofer Use The subwoofer will produce front channel low-frequency components (configurable in “Crossover”). Small The front speakers will produce LFE (low-frequency effect) channel audio and low-frequency components from other channels. The subwoofer or front speakers will produce center channel lowfrequency components (configurable in “Crossover”). Select this option for large speakers. Large None 54 En The center speaker will produce all of the center channel frequency components. Select this option when no center speaker is connected. The front speakers will produce center channel audio. Surround Extra Bass Selects whether or not surround speakers are connected and their sizes. Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy enhanced bass sounds, regardless of the size of the front speakers and the presence or absence of the subwoofer. Settings Select this option for small speakers. Small Large Settings The subwoofer or front speakers will produce surround channel lowfrequency components (configurable in “Crossover”). Off Disables Extra Bass. Select this option for large speakers. On Enables Extra Bass. The surround speakers will produce all of the surround channel frequency components. Note You can also use BASS on the remote control to enable/disable Extra Bass (p.36). Select this option when no surround speakers are connected. None The front speakers will produce surround channel audio. Virtual CINEMA DSP works when you select a sound program. Virtual CINEMA FRONT Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration. Crossover Settings Sets the lower limit of the low-frequency components that can be output from a speaker whose size is set to “Small”. A frequency sound lower than the specified value will be produced from the subwoofer or front speakers. Settings Off Disables the front 5-channel speaker configuration. On Enables the front 5-channel speaker configuration. Note 40 Hz, 60 Hz, 80 Hz, 90 Hz, 100 Hz, 110 Hz, 120 Hz, 160 Hz, 200 Hz ▪ Select “On” only when utilizing the Virtual CINEMA FRONT configuration (p.13). Note ▪ This setting is not available when “Surround” is set to “None”. If the volume and crossover frequency are adjustable on your subwoofer, set the volume to half and crossover frequency to maximum. n Distance Subwoofer Phase Sets the distance between each speaker and listening position so that sounds from the speakers reach the listening position at the same time. First, select the unit of distance from “Meter” or “Feet”. Sets the phase of the subwoofer. When the bass sound is lacking or unclear, switch the subwoofer phase. Choices Settings Front L, Front R, Center, Surround L, Surround R, Subwoofer Normal Does not reverse the subwoofer phase. Reverse Reverses the subwoofer phase. Setting range 0.30 m to 24.00 m (1.0 ft to 80.0 ft), 0.05 m (0.2 ft) increments Default Front L, Front R, Subwoofer: 3.00 m (10.0 ft) Center: 2.60 m (8.6 ft) Others: 2.40 m (8.0 ft) 55 En n Manual equalizer adjustment n Level 1 2 Adjusts the volume of each speaker. Choices Front L, Front R, Center, Surround L, Surround R, Subwoofer Setting range -10.0 dB to +10.0 dB (0.5 dB increments) 3 Default Front L, Front R, Subwoofer: 0.0 dB 4 Adjusts the tone with an equalizer. To exit from the menu, press SETUP. n Test Tone EQ Select Enables/disables the test tone output. Test tone output helps you to adjust the speaker balance or equalizer while confirming its effect. Selects the type of equalizer to be used. Settings Off Use the cursor keys (q/w) to select the desired band (frequency) and the cursor keys (e/r) to adjust the gain. -6.0 dB to +6.0 dB n Equalizer GEQ Use the cursor keys (q/w) to select “Channel” and the cursor keys (e/r) to select the desired speaker channel. Setting range Others: -1.0 dB PEQ Set “EQ Select” to “GEQ”. Settings Applies the parametric equalizer values obtained by the YPAO measurement (p.25). Off Does not output test tones. Select this option when you want to adjust the equalizer manually. On Outputs test tones automatically when you adjust the speaker balance or equalizer. For details, see “Manual equalizer adjustment”. Does not use the equalizer. Note “PEQ” is available only when the YPAO has been performed (p.25). 56 En HDMI Configures the HDMI settings. HDMI OUT (TV) Note Enables/disables the audio output from a TV connected to the HDMI OUT jack. Default settings are underlined. Settings n HDMI Control Off Disables the audio output from the TV. Enables/disables HDMI Control (p.79). On Enables the audio output from the TV. Settings Off n TV Audio Input Disables HDMI Control. Selects an audio input jack of the unit to be used for TV audio input when “HDMI Control” is set to “On”. The unit’s input source automatically switches to TV audio when the TV input is switched to its built-in tuner. Enables HDMI Control. On Configure the settings in “TV Audio Input”, “Standby Sync”, “ARC”, and “SCENE”. Settings Note AV 1–3, AUDIO 1–2 To use HDMI control, you need to perform the HDMI Control link setup (p.79) after connecting HDMI Control-compatible devices. Default AV 2 n Audio Output Note When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an external device because the input will be used for TV audio input. Selects a device to output audio. Note This setting is available only when “HDMI Control” is set to “Off”. Amp Enables/disables the audio output from the speakers connected to the unit. Settings Off Disables the audio output from the speakers. On Enables the audio output from the speakers. 57 En n Standby Sync n SCENE Select whether to use HDMI control to link the standby behavior of the TV and the unit when “HDMI Control” is set to “On”. Enables/disable SCENE link playback when “HDMI Control” is set to “On”. When SCENE link playback is enabled, HDMI Control-compatible devices connected to the unit via HDMI automatically works as follows, with a scene selection. Settings Off Does not set the unit to standby mode when the TV is turned off. On Sets the unit to standby mode when the TV is turned off. Auto • TV: turning on and displaying video from the playback device • Playback device: starting playback Choices (SCENE keys) Sets the unit to standby mode when the TV is turned off only when the unit is receiving TV audio or HDMI signals. BD / DVD, TV, CD, RADIO Settings n ARC Enables/disables ARC (p.19) when “HDMI Control” is set to “On”. Settings Off Disables SCENE link playback for the selected SCENE key. On Enables SCENE link playback for the selected SCENE key. Default Off Disables ARC. BD / DVD, TV: On On Enables ARC. CD, RADIO: Off Note You do not need to change this setting normally. In case noises are produced from the speakers connected to the unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off” and use the TV’s speakers. 58 Note SCENE link playback may not work properly due to the compatibility between devices. We recommend using TV and playback devices from the same manufacturer so that HDMI Control works more effectively. En Sound Configures the audio output settings. Center Image Note n DSP Parameter Adjusts the center orientation level (broadening effect) of the front sound field. Higher to strengthen the center orientation level (less broadening effect) and lower to weaken (more broadening effect). This setting is effective when “Neo:6 Music” is selected. Configures the surround decoder settings. Setting range Default settings are underlined. 0.0 to 0.3 to 1.0 Panorama Enables/disables the broadening effect of the front sound field. When this function is enabled, you can wrap front left/right channel sounds around the field and generate a spacious sound field in combination with the surround sound field. This setting is effective when “bPLII Music” is selected. Settings Off Disables the broadening effect of the front sound field. On Enables the broadening effect of the front sound field. n Lipsync Adjusts the delay between video and audio output. Note You can enable/disable the Lipsync function by input sources in “Lipsync (Lipsync)” (p.49) in the “Option” menu. Select Selects the method to adjust the delay between video and audio output. Center Width Setting range Adjusts the broadening effect of the center sound field. Higher to enhance the broadening effect, and lower to reduce it (closer to center). This setting is effective when “bPLII Music” is selected. Manual Adjust the audio output timing in “Adjustment”. Setting range 0 to 3 to 7 Auto Dimension Adjusts the delay between video and audio output automatically when a TV that supports an automatic lipsync function is connected to the unit via HDMI. If necessary, you can fine-adjust the audio output timing in “Adjustment”. Adjusts the difference in level between the front and surround sound fields. Higher to strengthen the front sound field and lower to strengthen the surround sound field. This setting is effective when “bPLII Music” is selected. Note “Select” is automatically set to “Manual” depending on the TV connected to the unit. Setting range -3 to 0 to +3 59 Select this option when you want to adjust the delay between video and audio output manually. En Adjustment Dynamic Range Adjusts the delay between video and audio output manually when “Select” is set to “Manual”. You can fine-adjust the audio output timing when “Select” is set to “Auto”. Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback. Settings Setting range 0 ms to 500 ms (1 ms increments) n Dialogue Maximum Produces audio without adjusting the dynamic range. Standard Optimizes the dynamic range for regular home use. Min/Auto Adjusts the volume of dialogue sounds. Dialogue Level Sets the dynamic range for clear sound even at night or at low volumes. When playing back Dolby TrueHD signals, the dynamic range is automatically adjusted based on the input signal information. Max Volume Adjusts the volume of the center orientation sounds such as dialogue. Sets the limit value of the volume. Setting range Setting range 0 to 3 (higher to strengthen) -30.0 dB to +15.0 dB (5.0 dB increments), +16.5 dB [50.0 to 95.0 (5.0 increments), 97.0] n Volume Initial Volume Configures the volume settings. Sets the initial volume when the receiver is turned on. Scale Settings Switches the scale of the volume display. Settings Off Sets the level to the volume level of the unit when it last entered standby mode. Sets the unit to mute the audio output. dB Displays the volume in the “dB” unit. Mute 0-97 Displays the volume in the numeric value (0.5 to 97.0). -80.0 dB to +16.5 dB (0.5 dB increments) Sets the level to the specified volume level. [0.5 to 97.0 (0.5 increments)] 60 En ECO Configures the power supply settings. Note Default settings are underlined. n Auto Power Standby Set the amount of time for the auto-standby function. Settings Off Does not set the unit to standby mode automatically. 20 minutes Sets the unit to standby mode when you have not operated the unit and the unit has not detected any input signal for the specified time. 2 hours, 4 hours, 8 hours, 12 hours Sets the unit to standby mode when you have not operated the unit for the specified time. Default U.K. and Europe models: 20 minutes Other models: Off Note Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front display. n ECO Mode You can reduce the unit’s power consumption by setting the eco mode to “On”. After setting, be sure to press ENTER to restart the unit. When the eco mode is enabled, you can reduce the unit’s power consumption. Settings Off Disables the eco mode. On Enables the eco mode. Note ▪ When “ECO Mode” is set to “On”, the front panel display may become dark. ▪ If you want to play audio at high volume, set “ECO Mode” to “Off”. 61 En Function Configures the functions that make the unit easier to use. Procedure to rename manually Note Default settings are underlined. 1 n Input Rename 2 Changes the input source name displayed on the front display. You can also select a name from the presets or a name created by the Auto Rename function. Use the cursor keys (q/w) to select an input source to be renamed. Use the cursor keys (e/r) to select “Manual” and press ENTER. Input sources Note HDMI 1-4, AUDIO 1-2, AV 1-3, USB, Bluetooth, AUX To select the preset name, use the cursor keys (e/r). Default 3 HDMI 1-4: Auto Others: Manual (For USB, Bluetooth, AUX only “Manual” can be selected.) The edit screen is displayed. 4 Procedure to rename automatically 1 2 Use the cursor keys (q/w) to select an input source to be renamed. To cancel the entry, select “CANCEL”. 5 6 Use the cursor keys (e/r) to select “Auto”. To check a created name, press ENTER. Note During selecting “Auto”, the created name is saved even after the device connection is terminated. To reset to the default setting, switch the setting to “Manual” at once and then set it again to “Auto”. 4 5 Use the cursor keys and ENTER key to edit the name, and then select “OK” to confirm the new name. Note The unit creates a name automatically according to the connected device. 3 Press ENTER. To change another input source name, repeat steps 1 to 3. To exit from the menu, press SETUP. 62 En To change another input source name, repeat steps 1 to 4. To exit from the menu, press SETUP. n Input Skip n Dimmer Set which input source is skipped when operating the INPUT key. Adjusts the brightness of the front display. You can select the desired input source quickly by using this function. Setting range Input sources -4 to 0 (higher to brighten) HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX Note Settings The front display may become dark when “ECO Mode” (p.61) is set to “On”. Off Does not skip the selected input source. On Skips the selected input source. n Memory Guard Prevents accidental changes to the settings. Settings Off Does not protect the settings. On Protects the settings until “Off” is selected. Note When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen. 63 En n Remote Color Key Language Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control. Select an on-screen menu language. Settings Default Note Default settings are underlined. Assigns the functions of playback devices connected to the unit with an HDMI cable. Settings Assigns the unit's input sources to each key. The assigned input sources can be set separately. Input Input sources HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, USB, Bluetooth, AUX Default RED: HDMI2, GREEN: HDMI4, YELLOW: AV 2, BLUE: AUX Assigns the functions of sound mode to each key. RED: MOVIE GREEN: MUSIC Program YELLOW: STEREO English English 日本語 Japanese Français French Deutsch German Español Spanish Русский Russian Italiano Italian 中文 Chinese BLUE: SUR.DECODE Note For example, if you press the RED key repeatedly, you can select your favorite sound program from the sound programs (MOVIE) (p.33) suitable for the video source. The information on the front display is provided in English only. 64 En Configuring the system settings (ADVANCED SETUP menu) Configure the system settings of the unit while viewing the front display. 1 2 ADVANCED SETUP menu items Set the unit to standby mode. Note Default settings are underlined. While holding down STRAIGHT on the front panel, press z (power). Item SP IMP. z (power) REMOTE ID 3 4 5 STRAIGHT Press PROGRAM to select an item. Page (U.S.A. and Canada models only) Changes the speaker impedance setting. Selects the unit’s remote control ID. (Asia, Taiwan and General models only) TU PROGRAM Function Changes the FM/AM tuning frequency setting. p.65 p.66 p.66 TV FORMAT Switches the video signal type of HDMI output. p.66 4K MODE Selects the HDMI 4K signal format. p.66 INIT Restores the default settings. p.67 UPDATE Updates the firmware. p.67 VERSION Checks the version of firmware currently installed on the unit. p.67 Press STRAIGHT to select a setting. Changing the speaker impedance setting (SP IMP.) Press z (power) to set the unit to standby mode and turn it on again. (U.S.A. and Canada models only) The new settings take effect. CHARGE OUT ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO SP IMP.••8¬MIN ADAPTIVE DRC VIRTUAL Change the unit’s speaker impedance settings depending on the impedance of the speakers connected. Settings 65 6 Ω MIN Select this option when you connect 6-ohm speakers to the unit. 8 Ω MIN Select this option when you connect 8-ohm or higher speakers to the unit. En Selecting the remote control ID (REMOTE ID) ENHANCER STEREO TUNED CHARGE OUT Switching the video signal type (TV FORMAT) SLEEP MUTE CHARGE OUT VOL. ECO REMOTE ID••ID1 ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO ADAPTIVE DRC VIRTUAL TV FORMAT•NTSC Change the unit’s remote control ID so that it matches the remote control’s ID (default: ID1). When using multiple Yamaha AV receivers, you can set each remote control with a unique remote control ID for its corresponding receiver. ADAPTIVE DRC VIRTUAL Switch the video signal type of HDMI output so that it matches to the format of your TV. Settings Since the unit automatically selects the video signal type so that it matches to the TV, it is unnecessary to change the setting normally. Change the setting only when images on the TV screen do not appear correctly. ID1, ID2 Settings NTSC, PAL n Changing the remote control ID of the remote control 1 Default U.S.A., Canada, Korea, Taiwan and General models: NTSC To select ID1, while holding down the cursor key (e), hold down SCENE (BD/DVD) for more than 3 seconds. To select ID2, while holding down the cursor key (e), hold down SCENE (TV) for more than 3 seconds. Other models: PAL Selecting the HDMI 4K signal format (4K MODE) Changing the FM/AM tuning frequency setting (TU) 4K MODE•MODE 2 Selects the format of signals input/output at the unit when HDMI 4K (60 Hz/50 Hz) compatible TV and playback device are connected to the unit. (Asia, Taiwan and General models only) CHARGE OUT ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO TU••••FM50/AM9 Settings ADAPTIVE DRC VIRTUAL Change the FM/AM tuning frequency setting of the unit depending on your country or region. MODE 1 Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:4:4, 4:2:2 or 4:2:0 format. Depending on the connected device or HDMI cables, video may not be displayed correctly. In this case, select “MODE 2”. Settings MODE 2 Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:2:0 format. FM100/AM10 Select this when you want to adjust the FM frequency by 100-kHz steps and AM by 10-kHz steps. FM50/AM9 Select this when you want to adjust the FM frequency by 50-kHz steps and AM by 9-kHz steps. Note When “MODE 1” is selected, use a high-speed HDMI cable that supports 18 Gbps. 66 En Checking the firmware version (VERSION) Restoring the default settings (INIT) ENHANCER STEREO TUNED CHARGE OUT SLEEP MUTE CHARGE OUT VOL. ECO INIT••••CANCEL ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO ADAPTIVE DRC VIRTUAL VERSION••xx.xx ADAPTIVE DRC VIRTUAL Restores the default settings for the unit. Check the version of firmware currently installed on the unit. Choices Note ALL Restores the default settings for the unit. CANCEL Does not perform an initialization. It may take a while until the firmware version is displayed. Updating the firmware (UPDATE) (Except for USA, Canada, Australia models) CHARGE OUT ENHANCER STEREO TUNED SLEEP MUTE VOL. ECO UPDATE•••••USB ADAPTIVE DRC VIRTUAL New firmware that provides additional features or product improvements will be released as needed. Updates can be downloaded from our website. For details, refer to the information supplied with updates. n Firmware update procedure Do not perform this procedure unless firmware update is necessary. Also, make sure you read the information supplied with updates before updating the firmware. 1 2 3 4 Save the downloaded firmware to the root folder of a USB memory device. Press PROGRAM on the front panel to select “UPDATE”. Connect the USB memory device to the USB jack. To start firmware update, press INFO on the front panel. 67 En APPENDIX Frequently asked questions The frequently asked questions from customers and the answers are shown below. I want to prevent accidental changes to the settings... The new speaker system does not provide an ideal sound balance... You can protect the settings configured on the unit (such as speaker settings) by utilizing “Memory Guard” in the “Setup” menu (p.63). If you have changed speakers or have a new speaker system, use YPAO to optimize the speaker settings again (p.25). If you want to adjust the speaker settings manually, use “Speaker” in the “Setup” menu (p.54). The unit’s remote control is simultaneously controlling another Yamaha product as well as the unit... When using multiple Yamaha products, the remote control may work on another Yamaha product or another remote control may work on the unit. If this happens, register different remote control IDs for the devices that you want to control with each remote control (p.66). We want to set limitations on the volume control... If someone accidentally operates the controls on the main unit or remote control, the volume may suddenly increase. This may also cause injury or damage the unit or speakers. We recommend using “Max Volume” in the “Setup” menu to set the maximum volume level for the unit in advance (p.60). The combination of video/audio input jacks does not match an external device... I want to fix the volume when turning on the unit... Use “Audio In” in the “Option” menu to change the combination of video/audio input jacks so that it matches the output jack(s) of your external device (p.21). By default, the volume level when the unit last entered standby mode is automatically applied. If you want to fix the volume, use “Initial Volume” in the “Setup” menu to set the volume to be applied when the receiver is turned on (p.60). Video and audio are not synchronized... Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output (p.59). The volume varies depending on the input sources... You can correct volume differences between input sources by utilizing “Input Trim” in the “Option” menu (p.49). I want to hear audio from the TV speakers... Use “Audio Output” in the “Setup” menu to select the output destination of signals input into the unit (p.57). Your TV speakers may be selected as an output destination. HDMI Control does not work at all... To use HDMI Control, you need to perform the HDMI Control link setup (p.79). After connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit, enable HDMI Control on each device and perform the HDMI Control link setup. This setup is required every time you add a new HDMI Control-compatible device to your system. For information on how HDMI Control works between your TV and playback devices, refer to the instruction manuals for each device. I want to change the on-screen menu language... Use “Language” in the “Setup” menu to select a language from English, Japanese, French, German, Spanish, Russian, Italian and Chinese (p.24). I want to update the firmware... Use “UPDATE” in the “ADVANCED SETUP” menu to update the unit’s firmware (p.67). I want to change the input source name... By default, input source names (such as “HDMI1” and “AV 1”) are displayed on the front display when an input source is selected. If you want to rename them as you like, use “Input Rename” (p.62) in the “Setup” menu. You can also select a name from the presets (such as “Blu-ray” and “DVD”). 68 En Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: 1 2 3 The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely. The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on. The connectors of each cable are securely inserted in to jacks on each device. Power, system and remote control Problem Cause Remedy The power does not turn on. The protection circuitry has been activated three times consecutively. As a safety precaution, capability to turn on the power is disabled. Contact your nearest Yamaha dealer or service center to request repair. The power does not turn off. The internal microcomputer has frozen, due to an external electric Hold down z (power) on the front panel for more than 15 seconds to reboot the shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet in the power supply voltage. and plug it again.) The power turns off (standby mode) immediately. The unit was turned on while a speaker cable was shorted. The sleep timer worked. The unit enters standby mode automatically. The unit is not reacting. Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers (p.17). Turn on the unit and start playback again. The auto-standby function activated because the unit was not used To disable the auto-standby function, set “Auto Power Standby” in the “Setup” for the specified time. menu to “Off” (p.61). The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers (p.65). The protection circuitry has been activated because of a short circuit. Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers (p.17). Hold down z (power) on the front panel for more than 15 seconds to reboot the The internal microcomputer is frozen, due to an external electric shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet in the power supply voltage. and plug it again.) 69 En Problem The unit cannot be controlled using the remote control. Cannot select the desired input source even if “INPUT” is pressed. The RED/GREEN/YELLOW/BLUE keys of the remote control do not operate. Cause Remedy The unit is out of the operating range. Use the remote control within the operating range (p.4). The batteries are weak. Replace with new batteries. The unit’s remote control sensor is exposed to direct sunlight or strong lighting. Adjust the lighting angle, or reposition the unit. The remote control IDs of the unit and the remote control are not identical. Change the remote control ID of the unit or the remote control (p.66). The function which skips some input sources is set. Set “Input Skip” of the desired input source in the “Setup” menu to “Off” (p.63). The device which is connected to the unit via HDMI does not support the operation of the RED/GREEN/YELLOW/BLUE keys. Use a device which supports the operation of the RED/GREEN/YELLOW/BLUE keys. The settings of the RED/GREEN/YELLOW/BLUE keys of the unit's remote control have been changed. Set the “Remote Color Key” settings in the “Setup” menu to “Default” (p.64). Audio Problem No sound. The volume cannot be increased. No sound is coming from a specific speaker. Cause Remedy Another input source is selected. Select an appropriate input source with the input selection keys. Signals that the unit cannot reproduce are being input. Some digital audio formats cannot be played back on the unit. To check the audio format of the input signal, use “Signal Info.” in the “Option” menu (p.49). The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable. The maximum volume is set. Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.60). A device connected to the output jacks of the unit is not turned on. Turn on all devices connected to the output jacks of the unit. The playback source does not contain a signal for the channel. To check it, use “Signal Info.” in the “Option” menu (p.49). The currently selected sound program/decoder does not use the speaker. To check it, select “5ch Stereo” (p.32). Audio output of the speaker is disabled. Perform YPAO (p.25) or use “Configuration” in the “Setup” menu to change the speaker settings (p.54). The volume of the speaker is set too low. Perform YPAO (p.25) or use “Level” in the “Setup” menu to adjust the speaker volume (p.56). The speaker cable connecting the unit and the speaker is defective. If there is no problem with the connection, replace with another speaker cable. The speaker is malfunctioning. To check it, replace with another speaker. If the problem persists, the unit may be malfunctioning. 70 En Problem Cause Remedy The playback source does not contain Low Frequency Effect (LFE) To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the or low-frequency signals. front channel low-frequency components from the subwoofer (p.55). No sound is coming from the subwoofer. Subwoofer output is disabled. Perform YPAO (p.25) or set “Subwoofer” in the “Setup” menu to “Use” (p.54). The volume of the subwoofer is too low. Adjust the volume on the subwoofer. The subwoofer has been turned off by its auto-standby function. Disable the auto-standby function of the subwoofer or adjust its sensitivity level. The TV does not support HDCP (High-bandwidth Digital Content Protection). Refer to the instruction manuals for the TV and check the TV’s specifications. No sound from the playback device (connected to The unit is set not to output audio input through HDMI jacks from the unit with HDMI). the SPEAKERS terminals. No sound from the TV (when HDMI Control is used). In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.57). The number of devices connected to the HDMI OUT jack exceeds the limit. Disconnect some of the HDMI devices. The TV is set to output audio from the TV speakers. Change the audio output setting on your TV so that the TV audio is output from the speakers connected to the unit. A TV that does not support ARC is connected to the unit only with an HDMI cable. Use a digital optical cable to make an audio connection (p.19). (If the TV is connected to the unit with an audio cable) The TV audio input setting does not match the actual connection. (If you are trying to use ARC) Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack (p.57). Set “ARC” in the “Setup” menu to “On” (p.58). Also, enable ARC on the TV. ARC is disabled on the unit or TV. When playing back DSD audio, the unit disables the audio output from a TV. The unit does not support DSD audio output from a TV. Change the audio output setting on the playback device to PCM. Only the front speakers work on multichannel audio. The playback device is set to output 2-channel audio (such as PCM) only. To check it, use “Signal Info.” in the “Option” menu (p.49). If necessary, change the digital audio output setting on the playback device. Noise/hum is heard. The sound is distorted. The unit is too close to another digital or radio frequency device. Move the unit further away from the device. The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable. The volume of the unit is too high. Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to “Off” (p.61). A device connected to the unit’s output jacks is not turned on. Turn on all devices connected to the unit’s output jacks. 71 En Video Problem No video. No video from the playback device (connected to the unit with HDMI). No image (contents required the HDCP 2.2 compatible HDMI device) from the playback device connected to the unit with HDMI. The menu of the unit is not displayed on the TV. Cause Remedy Another input source is selected on the unit. Select an appropriate input source with the input selection keys. Another input source is selected on the TV. Switch the TV input to display the video from the unit. The video signal output from the unit is not supported by the TV. Check the video output setting of the playback device. For information about video signals supported by the TV, refer to the instruction manuals for the TV. The cable connecting the unit and TV (or playback device) is defective. If there is no problem with the connection, replace with another cable. The input video signal (resolution) is not supported by the unit. To check the information about the current video signal (resolution), use “Signal Info.” in the “Option” menu (p.49). For information about video signals supported by the unit, see “HDMI signal compatibility” (p.81). The TV does not support HDCP (High-bandwidth Digital Content Protection). Refer to the instruction manuals for the TV and check the TV’s specifications. The number of devices connected to the HDMI OUT jack is over the limit. Disconnect some of the HDMI devices. The TV (HDMI input jack) does not support HDCP 2.2. (The Warning message can be displayed on the TV screen.) Connect the unit to the TV (HDMI input jack) that supports HDCP 2.2. The TV is not connected to the unit via HDMI. You can display the menu of the unit on the TV only when they are connected with an HDMI cable. If necessary, use an HDMI cable to connect them (p.19 to p.20). Another input source is selected on the TV. Switch the TV input to display the video from the unit (HDMI OUT jack). 72 En FM/AM radio Problem FM radio reception is weak or noisy. Cause Remedy There is multi-path interference. Adjust the FM antenna height or orientation, or place it in a different location. Your area is too far from the FM station transmitter. To select monaural FM radio reception “FM Mode” in the “Option” menu to “Mono” (p.37). The noises may be caused by fluorescent lamps, motors, thermostats, or other electrical equipment. It is difficult to completely eliminate noise. It may be reduced by using an outdoor AM antenna. Use an outdoor FM antenna. AM radio reception is weak or noisy. Select the station manually (p.37). Your area is too far from the FM station transmitter. Use an outdoor antenna. We recommend using a sensitive multi-element antenna. Adjust the AM antenna orientation. Radio stations cannot be selected automatically. Select the station manually (p.37). The AM radio signal is weak. AM radio stations cannot be registered as presets. Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with the supplied AM antenna. Auto Preset is for registering FM radio stations only. Register AM radio stations manually (p.38). Auto Preset has been used. USB (Except for USA, Canada, Australia models) Problem The unit does not detect the USB device. Folders and files in the USB device cannot be viewed. Cause Remedy The USB device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again. The file system of the USB device is not FAT 16 or FAT 32. Use a USB device with FAT 16 or FAT 32 format, except USB HDDs. The folder structure not supported by the unit is applied. The unit supports folder hierarchies of up to eight levels and up to 65,000 files per level. If necessary, modify the folder structure on your USB device. 73 En Bluetooth® Problem Cannot make the unit pair with a Bluetooth device. Cause Remedy Another Bluetooth device is connected. Terminate current Bluetooth connection, and perform pairing with the new device. This unit and the device are too far apart. Move the device closer to this unit. There is a device (microwave oven, wireless LAN, etc.) that outputs Move this unit away from the device that is emitting radio-frequency signals. signals in the 2.4 GHz frequency band nearby. The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP. Another Bluetooth device is connected. Terminate current Bluetooth connection, then establish a Bluetooth connection with that device again. The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device. Delete the pairing information of the device, and then perform pairing again (p.42). Cannot make a Bluetooth connection. The pairing information has been deleted. This unit can be paired with eight devices. If pairing with a ninth device is performed, the pairing information with the earliest connection date will be deleted. This unit is not registered on the device’s Bluetooth connection list. Perform paring again (p.42). The volume of the connecting device is set too low. Turn up the volume of the connecting device. The connecting device is not set to send Bluetooth audio signals to Switch the output of Bluetooth audio signals of the connecting device to the unit. the unit. No sound is produced, or the sound is interrupted during playback. The Bluetooth connection of the unit with the device has terminated. Perform Bluetooth connection operations again (p.43). There is a device (microwave oven, wireless LAN, etc.) that outputs Move this unit away from the device that is emitting radio-frequency signals. signals in the 2.4 GHz frequency band nearby. This unit and the connecting device are too far apart. 74 En Move the connecting device closer to this unit. Error indications on the front display Refer to the table below when the error message is indicated on the front display. Message Cause Remedy Access error The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. Check SP Wires The speaker cables short circuit. Twist the bare wires of the cables firmly and connect to the unit and speakers properly. Internal Error An internal error has occurred. Contact the nearest authorized Yamaha dealer or service center. No content There are no playable files in the selected folder. Select a folder that contains files supported by the unit. Not found The Bluetooth device is not found. RemID Mismatch The remote control IDs of the unit and the remote control are not identical. • Place the Bluetooth device within 10 m (32 ft) of the Bluetooth receiver. • Perform pairing again. Change the remote control ID of the unit or the remote control (p.66). 75 En Glossary This is a glossary of the technical terms used in this manual. DTS-HD Master Audio Audio information DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition home theater experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on BD (Blu-ray Disc). n Audio decoding format DTS Neo: 6 DTS Neo: 6 enables 6-channel playback from 2-channel sources. There are two modes available: “Music mode” for music sources and “Cinema mode” for movie sources. This technology provides discrete full-bandwidth matrix channels of surround sound. Dolby Digital Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that supports 5.1-channel audio. This technology is used for audio on most DVD disc. DSD (Direct Stream Digital) Dolby Pro Logic II Dolby Pro Logic II enables 5-channel playback from 2-channel sources. There are three modes available: “Music mode” for music sources, “Movie mode” for movie sources, and “Game mode” for game sources. DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as SACD (Super Audio CDs). The signals are stored at a high-frequency sampling rate of 2.8224 MHz. The highest frequency response is equal to or higher than 100 kHz, with a dynamic range of 120 dB. This technology offers better audio quality than that used for CDs. Dolby TrueHD MP3 Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to offer a high-definition home theater experience with the quality of the studio master. Dolby TrueHD can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on BD (Blu-ray Disc). One of the compressed digital audio format used by MPEG. With psychoacoustic technologies, this compression method achieves a high compression rate. Reportedly, it is capable of compressing data quantity by about 1/10 maintaining a certain level of audio quality. DTS 96/24 An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio streaming services on Internet because it allows a high compression rate of data while maintaining better audio quality than MP3. DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit audio. This format remains fully compatible with the existing multichannel audio systems that support DTS Digital Surround. This technology is used for music DVDs, etc. MPEG-4 AAC PCM (Pulse Code Modulation) DTS Digital Surround DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports 5.1-channel audio. This technology is used for audio on most DVD discs. PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted. This technology is the basis of all other audio format. This technology is used as a lossless audio format called Linear PCM for audio on a variety of media, including CDs and BD (Blu-ray Disc). DTS-ES Sampling frequency/Quantization bit DTS-ES creates total 6.1-channel audio from 5.1-channel sources that are recorded with DTS-ES. This decoder adds a surround back sound to the original 5.1-channel sound. In the DTS-ES Matrix 6.1 format, a surround back sound is recorded in the surround channels, and in the DTS-ES Discrete 6.1 format, a discrete surround back channel is recorded. Sampling frequency and quantization bits indicate the quantity of information when an analog audio signal is digitized. These values are noted as in the following example: “48 kHz/24-bit”. DTS Express DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a higher compression rate than the DTS Digital Surround format developed by DTS, Inc. This technology is developed for audio streaming services on the Internet and secondary audio on BD (Blu-ray Disc). • Sampling frequency Sampling frequency (the number of times the signal is sampled per second) is called the sampling rate. When the sampling frequency is higher, the range of frequencies that can be played back are wider. • Quantization bit The number of quantization bits indicate the degree of accuracy when converting the sound level into a numeric value. When the number of quantized bits is higher, the expression of the sound level is more accurate. DTS-HD High Resolution Audio WAV DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that supports 7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully compatible with the existing multichannel audio systems that support DTS Digital Surround. This technology is used for audio on most BD (Blu-ray Disc). Windows standard audio file format, which defines the method of recording the digital data obtained by converting audio signals. By default, the PCM method (no compression) is used, but you can also use other compression methods. 76 En Yamaha technologies WMA (Windows Media Audio) One of the compressed digital audio formats developed by Microsoft Corporation. With psychoacoustic technologies, this compression method achieves a high compression rate. Reportedly, it is capable of compressing data quantity by about 1/20 maintaining a certain level of audio quality. CINEMA DSP (Digital Sound Field Processor) n Others LFE (Low Frequency Effects) 0.1 channel This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to 120 Hz. This channel is added to the channels for all bands with Dolby Digital or DTS to enhance low frequency audio effects. This channel is labeled 0.1 because it is limited to only low frequency audio. Lip sync Since the Dolby Surround and DTS systems were originally designed for use in movie theaters, their effect is best experienced in a theater that has many speakers designed for acoustic effects. Since home conditions (such as room size, wall material, and number of speakers) can differ so widely, it is inevitable that there are differences in the sound that you hear. Based on a wealth of actually measured data, CINEMA DSP, Yamaha’s original DSP technology provides the audiovisual experience of a movie theater in your own home. Compressed Music Enhancer The Compressed Music Enhancer feature compensates for missing harmonics in compression music formats (such as MP3). As a result, this technology provides improved performance for the overall sound system. SILENT CINEMA Video output sometimes lags behind audio output due to the complexity of signal processing caused by an increase in video signal capacity. Lip sync is a technique for automatically correcting the timing lag between audio and video output. Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound program, so that accurate representations of all the sound programs can be enjoyed on headphones. Virtual CINEMA DSP HDMI and video information Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround speakers with front left and right speakers. Even if the surround speakers are not connected, the unit creates the realistic sound field in a listening room. Composite video signal With the composite video signal system, color, brightness, and synchronization data signals are combined and transmitted with a single cable. YPAO (Yamaha Parametric room Acoustic Optimizer) Deep Color Deep Color is a technology that HDMI specification supports. Deep Color increases the number of available colors within the boundaries defined by the RGB or YCbCr color space. Conventional color systems process the color using 8 bits. Deep Color processes the color with 10, 12, or 16 bits. This technology allows HDTVs and other displays to increase from millions of colors to billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle gradations between colors. The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. HDMI HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/ video signal transmission. This interface transmits both digital audio and digital video signals using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content Protection) and provides a secure audio/video interface. For further information on HDMI, visit the HDMI website at “http://www.hdmi.org/”. x.v.Color “x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color space than sRGB and allows the expression of colors that were not hitherto possible. While remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color space, and thus can produce more vivid, natural images. 77 En Supported devices and file formats Video signal flow The following devices and file formats can be used by the unit. Video signals input from a video device to the unit are output to a TV as shown below. Video device Supported devices The unit TV n USB devices (Except for USA, Canada, Australia models) • This unit supports USB mass storage class devices (e.g., flash memories or portable audio players) using FAT16 or FAT32 format. • Do not connect devices other than USB mass storage class devices (such as USB chargers or USB hubs), PCs, card readers, an external HDD, etc. HDMI connection • USB devices with encryption cannot be used. • Some features may not be compatible, depending on the model or manufacturer of the USB storage device. HDMI in HDMI HDMI out HDMI n Bluetooth® devices HDMI HDMI Composite video connection • Bluetooth devices that support A2DP can be used. • Yamaha does not assure the connections of all Bluetooth devices. VIDEO in VIDEO File formats n USB (Except for USA, Canada, Australia models) • The unit supports WAV (PCM format only), MP3, WMA and MPEG-4 AAC files (1- or 2-channel audio only). • The unit is compatible with sampling rate of up to 48 kHz. • Digital Rights Management (DRM) contents cannot be played back. 78 En VIDEO VIDEO out VIDEO VIDEO Information on HDMI (Example) The additional information on HDMI is as follows. HDMI Control HDMI Control HDMI Control allows you to operate external devices via HDMI. If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit (such as power and volume) with TV remote control operations. You can also control playback devices (such as HDMI Control-compatible BD/DVD players) connected to the unit with an HDMI cable. Playback starts Press SCENE (BD/DVD) Turns on and displays video from the playback device To use HDMI Control, you need to perform the following HDMI Control link setup after connecting the TV and playback devices. n Operations available from the TV’s remote control For details on settings and operating your TV, refer to the instruction manual for the TV. • Standby synchronization Note • Volume control including mute This setup is required every time you add a new HDMI Control-compatible device to your system. • Switching to input audio from the TV when the TV input is switched to its built-in tuner 1 2 • Switching to input video/audio from the selected playback device • Switching between audio output devices (the unit or TV speaker) (Example) HDMI Control HDMI Control HDMI Control Turn on the unit, TV, and playback devices. Configure the settings of the unit. 1 2 Switch the TV input to display video from the unit. Press SETUP. SLEEP SCENE BD DVD TV STRAIGHT CD RADIO ENHANCER BASS MUTE SETUP PROGRAM Playback device also turns off The unit turns off (standby) FM/AM SETUP USB INPUT OPTION VOLUME BLUETOOTH Turn off the TV MUTE SETUP Cursor keys ENTER OPTION ENTER ENTER n Operations available from the unit’s remote control RETURN TOP MENU DISPLAY HOME POP-UP/MENU RETURN RED GREEN YELLOW DISPLAYY DISPLA BLUE MEMORY TUNING • Starting playback on the playback device and turning on the TV with a scene selection (p.31) TUNING PRESET • Switching the TV input to display the “Setup” menu (when SETUP is pressed) • Controlling the playback device (playback and menu operations) 79 En TOP MENU HOME POP-UP/MENU 3 8 Use the cursor keys to select “HDMI” and press ENTER. Setup Speaker HDMI Sound ECO Note Function Language RETURN 4 ▪ If HDMI Control does not work properly, try unplugging the TV in Step 2 and plugging in the TV again in Step 3. It may solve the problem. Also, HDMI Control may not work if the number of connected devices exceeds the limit. In this case, disable HDMI Control on the devices not in use. Back ▪ If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting on the TV. Use the cursor keys (q/w) to select “HDMI Control” and the cursor keys (e/r) to select “On” as shown below. HDMI HDMI Control ▪ If you reconnect the HDMI cable, perform the procedure 5-8 again. ▪ We recommend using TV and playback devices from the same manufacturer so that HDMI Control works more effectively. On Audio Output TV Audio Input Standby Sync ARC AV2 Auto On SCENE RETURN 5 6 3 4 5 6 7 Check that the unit is properly synchronized with the TV by turning off the TV or adjusting the TV volume with the TV remote control. Back If you made a digital optical cable connection between the TV and the unit, use the cursor keys (q/w) to select “TV Audio Input” and the cursor keys (e/r) to select “AUDIO1”. Press SETUP. Enable HDMI Control on the TV and playback devices (such as HDMI Control-compatible BD/DVD players). Turn off the main power of the TV and then turn off the unit and playback devices. Turn on the unit and playback devices and then turn on the TV. Switch the TV input to display the video from the unit. Check the followings. On the unit: The input to which the playback device is connected is selected. If not, select the input source manually. On the TV: The video from the playback device is displayed. 80 En Audio Return Channel (ARC) HDMI signal compatibility ARC allows you to input TV audio to the unit with the HDMI cable which transmits video signal to the TV. n Audio signals Check the following after the HDMI Control settings. 1 2 Select a TV program with the TV remote control. Check that the input source of the unit will be automatically switched to “AV 2” and the TV audio will be played back on the unit. If you cannot hear the TV audio, check the following: ▪ “ARC” (p.58) in the “Setup” menu is set to “On”. ▪ The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI jack marked “ARC”) on the TV. Audio signal type Audio signal format 2ch Linear PCM 2ch, 32 to 192 kHz, 16/20/24 bit Compatible media (example) CD, DVD-Video, DVD-Audio Multichannel Linear PCM 8ch, 32 to 192 kHz, 16/20/24 bit DVD-Audio, BD (Blu-ray disc), HD DVD DSD 2 to 5.1ch, 2.8224 MHz, 1 bit SACD Bitstream Dolby Digital, DTS DVD-Video Bitstream (High definition audio) Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio, DTS-HD BD (Blu-ray disc), HD DVD High Resolution Audio, DTS Express n Video signals Some HDMI jack on the TV is not compatible with ARC. For details, refer to the instruction manual for the TV. The unit is compatible with the video signals of the following resolutions: Note • VGA • 720p/60 Hz, 50 Hz ▪ If the audio is interrupted while using ARC, set “ARC” (p.58) in the “Setup” menu to “Off” and use a digital optical cable to input TV audio to the unit (p.19). • 480i/60 Hz • 1080i/60 Hz, 50 Hz • 576i/50 Hz • 1080p/60 Hz, 50 Hz, 24 Hz ▪ When using ARC, connect a TV with an HDMI cable that supports ARC. • 480p/60 Hz • 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz ▪ “AV 2” is set as TV audio input at the factory. If you have connected any external device to the AV 2 jacks, use “TV Audio Input” (p.57) in the “Setup” menu to change the TV audio input assignment. To use the SCENE function (p.31), you also need to change the input assignment for SCENE (TV). • 576p/50 Hz Note ▪ When CPPM copy-protected DVD-Audio is played back, video/audio signals may not be output, depending on the type of the DVD player. ▪ The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For details, refer to the instruction manual for each device. ▪ To decode audio bitstream signals on the unit, set the input source device appropriately so that the device outputs the bitstream audio signals directly (does not decode the bitstream signals on the playback device). For details, refer to the instruction manual for the playback device. 81 En Trademarks The trademarks used in this manual are as follows. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks of DTS, Inc. © DTS, Inc. All Rights Reserved. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. x.v.Color™ “x.v.Color” is a trademark of Sony Corporation. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license. App Store is a service mark of Apple Inc. Android™ is a trademark of Google Inc. “SILENT CINEMA” is a trademark of Yamaha Corporation. 82 En Specifications The specifications of this unit are as follows. HDMI Input jacks HDMI Features: • 4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC (Audio Return Channel), HDMI Control (CEC), Auto Lip Sync, Deep Color, “x.v.Color”, HD audio playback, 21:9 Aspect Ratio, BT.2020 Colorimetry, HDR Compatible Analog Audio • Audio x 3 Video Format (Repeater Mode) • VGA • 480i/60 Hz • 576i/50 Hz • 480p/60 Hz • 576p/50 Hz • 720p/60 Hz, 50 Hz • 1080i/60 Hz, 50 Hz • 1080p/60 Hz, 50 Hz, 24 Hz • 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz Digital Audio (Supported frequencies: 32 kHz to 96 kHz) • Optical x 1 • Coaxial x 2 Video • Composite x 3 HDMI Input • HDMI x 4 Other jacks • USB x 1 (USB2.0) (Except for USA, Canada, Australia models) Audio Format • Dolby TrueHD • Dolby Digital Plus • Dolby Digital • DTS-HD Master Audio • DTS-HD High Resolution Audio • DTS Express • DTS • DSD 2-ch to 6-ch • PCM 2-ch to 8-ch (Max. 192 kHz/24-bit) Output jacks Analog Audio • Speaker Out x 5 (FRONT L/R, CENTER, SURROUND L/R) • Subwoofer Out x 1 • Headphone x 1 Video • Composite x 1 HDMI Output • HDMI OUT x 1 Content Protection: HDCP 2.2 compatible Link Function: CEC supported Other jacks TUNER YPAO MIC x 1 Analog Tuner • [U.K. and Europe models] FM/AM with Radio Data System x 1 (TUNER) • [Other models] FM/AM x 1 (TUNER) 83 En USB (Except for USA, Canada, Australia models) Rated Output Power (1-channel driven) Capable of Mass Storage Class USB Memory • [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω) • [Other models] (1 kHz, 0.9% THD, 6 Ω) Current Supply Capacity: 0.5 A Bluetooth Bluetooth version • Ver. 2.1+EDR – Front L/R 100 W/ch – Center 100 W/ch – Surround L/R 100 W/ch Maximum Effective Output Power (1-channel driven) • [U.S.A. and Canada models] Supported profile • A2DP (1 kHz, 10% THD, 8 Ω) – Front L/R, Center, Surround L/R 130 W/ch Supported codec • SBC (1 kHz, 10% THD, 6 Ω) – Front L/R, Center, Surround L/R 140 W/ch • [Other models] (1 kHz, 10% THD, 6 Ω) Wireless output • Bluetooth Class 2 – Front L/R, Center, Surround L/R Dynamic Power (IHF) Maximum communication distance • 10 m (33 ft) without interference • [U.S.A. and Canada models] – Front L/R (8/6/4/2 Ω) Compatible Decoding Formats – Front L/R (6/4/2 Ω) • Front L/R, 20 Hz to 20 kHz, 8 Ω • AV 2 etc. (1 kHz, 100 W/6 Ω) 200 mV/47 kΩ Maximum Input Signal • AV 2 etc. (1 kHz, 0.5% THD, Effect On) 2.3 V Output Level / Output Impedance • SUBWOOFER Rated Output Power (2-channel driven) • [U.S.A. and Canada models] (20 Hz to 20 kHz, 0.09% THD, 8 Ω) • [Other models] (20 Hz to 20 kHz, 0.09% THD, 6 Ω) 1 V/1.2 kΩ Headphone Jack Rated Output / Impedance • AV 2 etc. (1 kHz, 50 mV, 8 Ω) 70 W+70 W • [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω) – Surround L/R 100 or more Input Sensitivity / Input Impedance Audio Section – Center 110/130/150 W Damping Factor Post Decoding Format • Dolby Pro Logic • Dolby Pro Logic II Music, Dolby Pro Logic II Movie, Dolby Pro Logic II Game • DTS Neo: 6 Music, DTS Neo: 6 Cinema – Front L/R 110/130/160/180 W • [Other models] Decoding Format • Dolby TrueHD, Dolby Digital Plus • Dolby Digital • DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Express • DTS, DTS 96/24, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1 – Front L/R 135 W/ch 100 mV/470 Ω Frequency Response 85 W+85 W • AV 2 etc. to Front (10 Hz to 100 kHz) 85 W 85 W+85 W 84 En +0/-3 dB FM Section Signal to Noise Ratio (IHF-A Network) • AV 2 etc. (Input 1 kΩ Shorted, Speaker Out) 110 dB or more Tuning Range • [U.S.A. and Canada models] Residual Noise (IHF-A Network) • Front L/R (Speaker Out) • [Asia, Taiwan, Brazil and General models] 150 μV or less • [Other models] Channel Separation • AV 2 etc. (Input 1 kΩ Shorted, 1 kHz/10 kHz) • Step • Mono • Bass Turnover • Treble Boost/Cut • Treble Turnover 0.5 dB • Mono 65 dB • Stereo 64 dB Harmonic Distortion (IHF, 1 kHz) ±6 dB/0.5 dB Step at 50 Hz 350 Hz ±6 dB/0.5 dB Step at 20 kHz 3.5 kHz • Mono 0.5% • Stereo 0.6% Antenna Input 75 Ω unbalanced Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz) • H.P.F. (Front, Center, Surround) 12 dB/oct. • L.P.F. (Subwoofer) 24 dB/oct. AM section Tuning Range • [U.S.A. and Canada models] Video Section • [Asia, Taiwan, Brazil and General models] • [Other models] Video Signal Type • [U.S.A., Canada, Korea, Taiwan, Brazil and General models] • [Other models] NTSC 530 kHz to 1710 kHz 530/531 kHz to 1710/1611 kHz 531 kHz to 1611 kHz General PAL Power Supply Video Signal Level • Composite 3 μV (20.8 dBf) Signal to Noise Ratio (IHF) MUTE, -80 dB to +16.5 dB Tone Control Characteristics • Bass Boost/Cut 87.50 MHz to 108.00 MHz 50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.) 70 dB/50 dB or more Volume Control • Range 87.5 MHz to 107.9 MHz 87.5/87.50 MHz to 108.0/108.00 MHz • [U.S.A. and Canada models] 1 Vp-p/75 Ω • [Taiwan, Brazil and General model] Video Maximum Input Level 1.5 Vp-p or more • [Korea model] AC 220 V, 60 Hz • [Australia model] AC 240 V, 50 Hz • [U.K. and Europe models] • [Asia model] Video Signal to Noise Ratio 50 dB or more AC 120 V, 60 Hz AC110 to 120/220 to 240 V, 50/60 Hz AC 230 V, 50 Hz AC 220 to 240 V, 50/60 Hz Power Consumption 260 W 85 En Standby Power Consumption • HDMI Control Off – [Taiwan, Brazil and General model] 0.5 W – [Other models] 0.3 W • HDMI Control On (No Signals) 0.9 W Maximum Power Consumption • [Taiwan, Brazil and General models] 470 W Dimensions (W x H x D) 435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”) Weight 7.4 kg (16.3 lbs) * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. 86 En Yamaha Global Site http://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Department © 2016 Yamaha Corporation Published 01/2016 NV-A0 YH631A0/EN2