Transcripción de documentos

V2.0 Supplementary Manual This supplementary manual explains mainly the functions that have been added or changed in CL5/CL3/CL1 firmware V2.0. Use it in conjunction with the CL5/CL3/CL1 Owner’s Manual, Reference Manual, and V1.7 Supplementary Manual. EN  Contents Contents SELECTED CHANNEL section ...................................................... 3 Added fader function............................................................................................... 3 Added insert function .............................................................................................. 3 Input channels .......................................................................... 4 Added gain function ................................................................................................ 4 Grouping and linking ............................................................... 5 DCA Roll-out function.............................................................................................. Added DCA output channels ................................................................................... Added mute group function .................................................................................... Added channel link function .................................................................................... Added channel job function..................................................................................... 5 6 7 7 7 Scene memory........................................................................... 8 Added scene memory function ................................................................................ 8 Graphic EQ, Effects, and Premium Rack ................................... 9 Enhanced Graphic EQ functions............................................................................... 9 User settings ........................................................................... 10 Functions added to the channel name display ....................................................... 10 Recorder (Nuendo Live) .......................................................... 10 Added Recorder (Nuendo Live) function ................................................................ 10 Other functions....................................................................... 11 Added GPI functions .............................................................................................. Added functions that can be assigned to the USER DEFINED keys .......................... Added functions that can be assigned to the USER DEFINED knobs ....................... Added functions that can be assigned to the assignable encoders.......................... 11 11 11 11 2 V2.0 Supplementary Manual  SELECTED CHANNEL section SELECTED CHANNEL section Added insert function You can now insert two devices into a single channel or bus. Added fader function ■ Setting inserts The TOUCH AND TURN function assigned to one of the USER DEFINED knobs enables you to control the fader in the FADER field of the SELECTED CHANNEL VIEW screen. 1. Use a bank select key or [SEL] key to select the channel or bus to which you want to insert devices. 2. In the INSERT field of the SELECTED CHANNEL VIEW screen, press the popup button to open the INSERT/DIRECT OUT popup window (1ch). (In the OVERVIEW screen, press the INSERT/DIRECT OUT field to access the INSERT popup window (8ch).) INSERT OUT buttons 3. 3 INSERT IN buttons Press the INSERT OUT or INSERT IN button. V2.0 Supplementary Manual  Input channels 4. Input channels Select an output port or input port. NOTE • There is a limit to the sum of INSERT 1 and INSERT 2 for each channel group, as shown in the table below. You can select any output or input ports. CH1-16 CH17-32 CH33-48 CH49-64 (CL5 and CL3 only) Added gain function CH65-72 MIX1-24/ MATRIX1-8 (CL5 only) ST/MONO INSERT OUT 16 16 16 16 8 30 8 INSERT IN 16 16 16 16 8 30 8 • If you exceed the INSERT OUT or INSERT IN limitation, the If GC (Gain Compensation) is enabled, you can link the digital gain to the analog gain operation. While you are controlling the analog gain, the Gain Compensation function enables you to modify the level on your own console without affecting the level of other consoles. ■ Linking the gains indicator will light up on the left. 1. Press the GAIN knob in the GAIN/PATCH field in the OVERVIEW screen (or SELECTED CHANNEL VIEW screen). 2. Press the 1ch tab or 8ch tab in the GAIN/PATCH popup window. AG➞DG ALL ON button/ AG➞DG ALL OFF button AG➞DG ALL ON button/ AG➞DG ALL OFF button AG➞DG LINK button 3. Press the AG➞DG LINK button to turn the link on. Using the AG→DG ALL ON button and AG→DG ALL OFF button enables you to turn the link between the analog and digital gain for all input channels simultaneously. You can also view the link status in the SELECTED CHANNEL VIEW screen. • If the limit is exceeded, invalid ports will be marked with a strike-out line. • If the limit is exceeded, the following ports will take priority per channel group (listed in the table above.) 1 INSERT 1 will take priority over INSERT 2. 2 Lower-number channel will take priority. : Link is on. : Link is off. 4 V2.0 Supplementary Manual  Grouping and linking ■ Setting the DCA Roll-out function Grouping and linking 1. In the Function Access Area, press the CH JOB button. DCA Roll-out function DCA GROUP button You can now access all of the channels assigned to a DCA group simultaneously through the fader banks. This function enables flexible fader operations. For example, while controlling the DCA fader in the Centralogic section, you can use the Roll-out function to access (roll-out) and control the faders (assigned to the corresponding DCA group) through the fader bank located to the left of the Centralogic section. Alternatively, you can control the faders rolled out to the Centralogic section via DCA Roll-out, while operating the DCA faders through the fader bank on the left. ■ DCA Roll-out operation 1. Use a bank select key to select the DCA group that you want to control, then press the [SEL] key for that DCA group. DCA Roll-out mode is engaged, and the faders that have been assigned to the DCA group will be rolled out. 2. If you press the [SEL] key for another DCA group, faders that have been assigned to that DCA group will be rolled out. 3. 2. Press the DCA GROUP button to access the DCA/MUTE GROUP ASSIGN MODE popup window. DCA ROLL-OUT button Press the same [SEL] key again to exit DCA Roll-out mode. NOTE • You cannot turn Roll-out mode on while operating the DCA group (for example, while assigning channels or editing the group name). • Even if Roll-out mode is turned on while you are controlling a GEQ via faders, you cannot edit the DCA group using the faders. • If the number of channels assigned to a DCA group exceeds the number of faders in the block (that is a roll-out target), you will be unable to control extra channels. • All bank select keys in the block (to which the displayed channels belong) will light up. • If the faders are rolled out to the Centralogic section (block B), the IN/OUT select keys in the Centralogic section will be disabled. • Bank select keys in blocks in which no faders are rolled out will operate normally. 3. 5 Press the DCA ROLL-OUT button. V2.0 Supplementary Manual  Grouping and linking Added DCA output channels You can now assign the Stereo/Mono bus master, Mix bus master, and Matrix bus master channels to a DCA group. DCA groups were formerly used exclusively for input channels. However, with this new feature, you can use the DCA groups for output master channels, which enables for more flexible simultaneous controls. 2 1 1. In the Function Access Area, press the CH JOB button. 2. Press the DCA GROUP button to access the DCA/ MUTE GROUP ASSIGN MODE popup window. DCA GROUP button 3 1 ROLL-OUT BLOCK Enables you to select a block in which the DCA group is rolled out to the faders. CL5 : Blocks A, B, C CL3/CL1 : Blocks A, B DCA GROUP select button 2 ALIGN button Enables you to choose whether the DCA group is rolled out to the faders from the left or right. 3 DCA group select button Selects the DCA group that you want to control. 4. Select the DCA group that you want to control. If you press a [SEL] key for a DCA group other than the selected one, the group selection will change. 5. Select a block (in which the DCA group is rolled out to the faders) and the alignment. 6. Press the CLOSE button to close the popup window. NOTE 3. Use the DCA GROUP select buttons to select the DCA group to which you want to assign channels. 4. Press the [SEL] key for the output channel to select the channel that you want to assign. 5. When you finish assigning the channels, press the CLOSE button to close the popup window, then press the “x” symbol in the Function Access Area (CH JOB display). You cannot turn DCA Roll-out mode on if one of the following popup windows is open. If DCA Roll-out mode is already turned on, opening one of the windows will cause DCA Roll-out mode to quit. - DCA/MUTE GROUP ASSIGN MODE popup window - RECALL SAFE MODE popup window 6 V2.0 Supplementary Manual  Grouping and linking 2. Added mute group function The MIX MINUS popup window will open. You can now unmute a muted channel in the mute group temporarily. If the master button is turned on for the mute group to which the target channel belongs, press the [ON] key for that channel to temporarily unmute the channel. However, in Preview mode, any operation during mute will be invalid. Added channel link function Recall Safe parameters are now linked for linked channels. If you specify Recall Safe parameters for the selected channel in the RECALL SAFE MODE popup window, the Recall Safe parameter setting will be effective on other channels that are linked to the selected channel. Added channel job function Now CL units support the Mix Minus function, which removes a specific channel signal from the signals sent to the MIX/MATRIX buses. You can use this function to quickly send monitoring signals to a performer or announcer simply by removing his or her audio signal. NOTE This Mix Minus function is a shortcut for settings, rather than an operation to switch between modes. Therefore, even after using this function, you can still edit any parameter on the window without restrictions. HINT You can also access the MIX MINUS popup window by pressing the CH JOB button in the Function Access Area, then pressing the MIX MINUS button. ■ Mix Minus operation 1. While holding down the [SEL] key, press the MIX knob or MATRIX knob in the SELECTED CHANNEL section. 3. If you wish to remove an additional input channel, press the corresponding [SEL] key. 4. If necessary, in the DESTINATION field, select a bus. NOTE You cannot select a FIXED bus. 5. Press the OK button to set the parameters as follows: • The send level of the signals sent from the selected input channels is lowered to –∞ dB. • The send level of the signals sent from all other input channels is set to nominal (0.0dB). • Send to the destination bus is turned on, and the send point is switched to POST. NOTE For the stereo input channels, the send level of the signal sent from both channels is set to –∞ dB. 7 V2.0 Supplementary Manual  Scene memory Scene memory • R (READ ONLY) symbol Not only will the scene be protected, it will also not be overwritten by any file loaded from a USB flash drive. You can only apply the protect setting to scenes with consecutive scene numbers starting with scene #001. Added scene memory function • No symbol No scene will be protected. Now you can create a read-only scene memory. By specifying certain scenes as read-only, you can prevent those scenes from being overwritten when you load a console file. NOTE The R symbol for scene number 000 cannot be disabled. ■ SCENE LIST window 1 1 R symbol (READ ONLY)/Protect symbol An “R” symbol is displayed for read-only scenes, and a protect (lock) icon is displayed for writeprotected scenes. To enable/disable the scene protect setting, press the R symbol or protect symbol of the selected scene. Pressing the protect (lock) symbol or the R (read-only) symbol repeatedly will switch between displaying and hiding the corresponding symbol. • Protect (lock) symbol You will be unable to overwrite the scene. 8 V2.0 Supplementary Manual  Graphic EQ, Effects, and Premium Rack Graphic EQ, Effects, and Premium Rack Enhanced Graphic EQ functions Now you can compare the sound before and after gain adjustments during GEQ operations. In the GEQ popup window, use the buttons in the FADER ASSIGN field to specify the frequency band you want to control. Adjust the gain value using the fader assigned for the specified frequency band. Press the lit [ON] key to make it go dark, and the gain value of the corresponding frequency band will immediately return to ± 0dB. With CL version 2.0 or later, pressing the [ON] key again for this band will restore the adjusted gain value. In this way, comparison is easy and quick. However, please note that if the [ON] key for this band is off and if you press the [ON] key for the fader of a different frequency band, the adjusted gain value will be canceled and will return to ± 0dB. 9 V2.0 Supplementary Manual  User settings User settings Recorder (Nuendo Live) Functions added to the channel name display Added Recorder (Nuendo Live) function You can now view the gain reduction meters for Dynamics 1 and 2, as well as other information, on the channel name display. In addition, if a channel is off during SENDS ON FADER mode, the channel name display will be highlighted. The current CL version supports Yamaha Console Extension V2. Due to this support, you can now edit the marker description from the console. ■ Editing the marker description 1. On the Preference page, you can choose whether you want to view (a) only the channel name and number, (b) gain reduction meters, or (c) the channel encoder value. In the Function Access Area, press the RECORDER button to access the RECORDER screen. Select NAME ONLY to display only the channel name and number. Select GR METER to display the GR meters and fader level value. Select ENCODER INFO to display the information of a function that has been assigned to the GAIN/ PAN/ASSIGN knob on the channel fader strip. This option is the same as the FULL FUNCTION option in CL version 1.7 or earlier. 1 GR meters indicator NOTE The GR meters function enables you to easily view the movement of the gain reduction. 2. Press the NUENDO Live tab in the upper-right of the screen. 1 Marker list field When you press this field, a keyboard window allowing you to edit the marker information will appear. 3. 10 Use the keyboard window to edit the marker description. V2.0 Supplementary Manual  Other functions Other functions Function PARAMETER 1 SENDS ON FADER MIX1-24 PARAMETER 2 NORMAL/WITH CUE Added GPI functions MTRX1-8 NORMAL/WITH CUE New functions have been added that can be set for GPI OUT. MIX ON FADER NORMAL/WITH CUE Function DANTE PARAMETER 1 PARAMETER 2 REDUNDANCY IND. PRIMARY SECONDARY Description MATRIX ON FADER NORMAL/WITH CUE This function activates when the primary connection is working properly on the Dante audio network with a star connection (redundancy network). SENDS ON FADER This function activates when the secondary connection is working properly on the Dante audio network with a star connection (redundancy network). NORMAL/WITH CUE Description This function switches between the normal function on/off (NORMAL), and the function with cue on/off (WITH CUE). With the WITH CUE option, cue will be enabled if SENDS ON FADER mode is engaged or if you switch mode during SENDS ON FADER mode. Also, with the WITH CUE option, cue for all output channels will be canceled if SENDS ON FADER mode is disengaged. Added functions that can be assigned to the USER DEFINED knobs New functions have been added that can be assigned to the USER DEFINED knobs. Added functions that can be assigned to the USER DEFINED keys DIRECT OUT LEVEL New functions have been added that can be assigned to the USER DEFINED keys. Function PARAMETER 1 PARAMETER 2 Description CUE CUE MODE This function switches the cue mode. DCA ROLL-OUT LAST DCA SEL This function rolls out or retracts the selected DCA group. DCA1 Function PARAMETER 2 SELECTED CH, CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48 OUTPUT LEVEL LEVEL MIX1–MIX24, MTRX1–MTRX8, ST L, ST R, MONO (C) SCENE SELECT RECORDER INPUT GAIN OUTPUT GAIN Description of PARAMETER 1 for function SET BY SEL has been changed to match the description for the QL series. The name of function SEND ENCODER MODE has been changed to SEND MODE. : DCA16 FADER BANK SNAPSHOT PARAMETER 1 LEVEL This function takes a snapshot of the bank settings for all blocks (A, B, and C). (Hold down the key for two seconds or longer.) Alternatively, this function displays the last snapshot of the bank settings. (Hold down the key, then release it within two seconds.) Added functions that can be assigned to the assignable encoders New functions have been added that can be assigned to the assignable encoders (GAIN/PAN/ASSIGN knobs). NUENDO LIVE ADD MARKER This function executes ADD MARKER of NUENDO Live. SCENE INC This function selects the next existing scene number. NO ASSIGN (Nothing will be displayed.) DIGITAL GAIN D.GAIN DEC This function selects the previous existing scene number. EQ ATT ATT INPUT DELAY DELAY Units of scale are m, ms, and ft. No description for samples. DIRECT OUT LEVEL D.OUT RECALL This function recalls the currentlyselected scene. STORE This function stores the current settings. Function 11 Channel name display indication V2.0 Supplementary Manual  Yamaha Pro Audio Global Web Site http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ C.S.G., PA Development Division © 2014 Yamaha Corporation Published 06/2014 IP-A0