Transcripción de documentos

ZT16380 Connections EN POWER AMPLIFIER Attaching Euroblock Plugs Connecting a Control Panel Example (connection to the [REMOTE] connector) 1 Loosen Slotted screwdriver 2 3 Approx. 5 mm (approx. 0.2”) Tighten Thank you for your purchase of the Yamaha PA2120 power amplifie . Please read through this manual carefully before beginning use, so that you will be able to take full advantage of the device’s various functions. After you have read the manual, keep it in a safe place. • The illustrations as shown in this manual are for instructional purposes only. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. 4 200m (according to DCH8 specifications). If you need a longer connection, we ecommend not using the DCH8, but connecting the devices in a daisy-chain configuration Features • • • • Complies with the ENERGY STAR international standard for energy efficient p oducts. Supports both high-impedance and low-impedance speaker connections. Source and volume zoning capability for two zones in mono connection. Equipped with an auto-wake function that turns the power on after detecting an input signal when in standby mode. • Able to be remotely controlled by connecting a DCP series control panel. • Built-in “Speaker EQ” that allows for tuning the sound quality to be perfect for use with Yamaha speakers. Accessories (Please confirm that all items are included) • Power cord • Euroblock plugs (6-pin x 1, 3-pin x 1, both with a 3.5mm pitch) • Technical Specifications (English only): includes block diagrams, dimensions, and input/output specifications • Owner’s Manual (this sheet) Precautions when connecting two control panels: • Connect them in a daisy-chain configuration • Set the panel IDs separately. (0 or 1) • Set the second control panel DIP switch 4 to ON. (termination setting) This setting is only for the second device when connecting two devices. • Ensure that the total Ethernet cable length does not exceed 800 meters in the case of 24AWG. Terminal screw Euroblock plug NOTE • You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer. 1 2 3 4 • To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device, use a lacing bar when possible to bundle and fasten the cables. • Do not tin (solder) the exposed end. Panel ID setting for control panel ON 1 Loosen terminal screws. ■ When multiple speakers are connected to the two zones: (MODE: MONO) Connecting Speaker Cables Zone A: 15W x 6 = 90W 2 3 1 2 3 1 2 3 1 2 3 1 2 3 4 5 6 7 1 2 3 1 2 3 1 2 3 1 2 3 Rear panel Rear panel ON 1 Set the DIP switch 4 to ON (termination setting). (The second control panel only if connecting 1 2 3 4 two devices.) Sets the panel ID ON 2 3 4 Sets the panel ID Speaker transformer 70V/100V 10W Caution • Ensure that load is not applied to the speaker cable. • This device uses a BTL (Balanced Transformer-Less) connection method for the amplifier output. As the amplifier output is sent to the positive and negative connectors, any contact with other terminals or the device chassis may lead to malfunction. Loosen the screw, insert the spade lug all the way from below, and tighten the screw. DCP1V4S When using a bare conductor Encoder Volume control Loosen the screw, wrap the conductor wire around the barrier strip terminal, and tighten the screw. Be sure that the bare wire does not touch the chassis. Switch 3 Encoder operation target: SPEAKER A Switch 2 Volume up: SPEAKER A ≥3.2mm (≥ 0.13”) 15mm* (0.6”) ≤5.8mm (≤0.23”) Switch 4 Encoder operation target: SPEAKER B 4Ω Volume down: SPEAKER A Switch 3 Encoder 3 Volume up: SPEAKER B Serial Connection When connected in series, the total impedance is simply the sum of the impedances of the speaker systems connected. However, if one speaker system happens to fail, the electrical signal will not be passed on and subsequent speaker systems will be affected. Volume control: SPEAKER B NOTE • Controls not listed here will not work. 4Ω • Settings by using control panels will be retained even if the control panels have been disconnected. Using the [REMOTE] Connector (Euroblock 3-pin) You can connect switches to the rear panel [REMOTE] connector, and use them to remotely mute/unmute all channels, or switch the power standby/on status. From the left, the [REMOTE] connector consists of M (mute all), S (standby), and G (ground) pins. The [REMOTE] connector uses a Euroblock plug. For details on how to connect Euroblock plugs, refer to “Attaching Euroblock Plugs.” Connect a BGM (background music) tuner, a CD player, a portable audio player, etc. to the stereo input jacks of this device. After finishing all connections, connect the power co d to an AC outlet. When connecting the power cord to an AC outlet, an input signal will turn on the power of this device by the auto-wake function. To avoid unexpected loud sounds, be sure to connect microphones and external devices with the power off status. Muting/unmuting all channels Turning mute on Turning mute off 8Ω Total impedance = 4Ω Volume down: SPEAKER B Encoder 4 Volume control: SPEAKER A 8Ω Switch 4 DCP4V4S * Actual size 10W Cannot be connected 8Ω Switch 1 Wire should not touch the chassis. 10W Parallel Connection When multiple speaker systems having the same impedance are connected in parallel, the total impedance becomes the individual speaker system impedance divided by the number of systems connected. DCP4S Speaker cable 10W When connecting multiple low-impedance speaker systems to a single channel, the following methods are possible. ■ Functions Operated Via the Control Panel NOTE Connect the cables so that the amplifier s “+” and “-” symbols match those of the speaker. If they are reversed, the 10W Low-Impedance Connections PA2120 rear panel RCA Switching the power standby/on status Switching the power to standby Turning the power on BMG source Zone B: 7.5W x 10 = 75W As long as the total nominal power input rating for all speakers is within the power output capability of the amplifie , any number of speaker systems can be connected in parallel. The power input rating is determined by the speaker systems and speaker transformers used. It is also possible to connect speaker systems that have different input power ratings. In the case of speaker systems that are capable of changing their input power rating (Yamaha VXC and VXS series, etc.), this can be utilized to vary the volume of each speaker. Ethernet straight cable (CAT5e or more; 800m or less (24AWG)) Euroblock DCP (for zone B) High-Impedance Connections The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections are described below for two methods: using a spade lug and using a bare conductor. Warning DCP (for zone A) 4 RJ-45 Connecting External Devices Setup Example 3 1 For a high-impedance connection, a speaker transformer that raises the impedance to several hundred or thousand ohms is added to the speaker system. This allows the speaker system to be effectively driven with much lower current than is required for a low-impedance connection. Therefore, a large number of speaker systems can be connected. Even over long distances, there is very little transmission loss due to the cable resistance being negligible in relation to the impedance of the speaker system. High-impedance speaker connections usually operate at a specific maximum power amplifier voltage of 100 or 70 volt The more orthodox low-impedance connection does not use a speaker transformer. The speaker systems are directly connected to the power amplifier with a rated impedance generally a ound 4 - 16 ohms. For short distances over which cable resistance is insignificant, low-impedance connections deliver a sound quality that is superior to high-impedance connections. The differences between connection methods are explained as follows. ■ Multiple Speaker System Drive Capability Yamaha Digital Control Panel Insert the Euroblock plug into a terminal of this device. Auto-Standby and Auto-Wake Functions To reduce energy consumption, this device enters into standby mode when no input signal is detected for 25 minutes. It is also equipped with an auto-wake function that automatically turns the power on when an input signal is detected while in standby mode. Even when the device has been put into standby mode by the autostandby function, any microphone or BGM audio input will restore the power. The auto-wake function is turned on by default. The auto-wake function can be turned on or off by changing the rear panel [SETUP] DIP switch setting. (Refer to “Controls and Functions.”) 2 Securely tighten terminal screws. When using a spade lug This device complies with the ENERGY STAR international standard for energy efficient products. It automatically enters into standby mode when no input signal is detected for 25 minutes in order to save power while not in use. In addition, a highly efficient amplifier c cuitry design has been adopted to reduce energy consumption while the device is in use. 0 Insert cables. phase will be reversed and the sound will not be output correctly. ENERGY STAR Certification High-Impedance and Low-Impedance Connections Connecting Yamaha Digital Control Panel (DCP1V4S, DCP4S, DCP4V4S) to PA2120 enables you to control the volume remotely. You can connect up to two control panels. The total length of the cables from the PA2120 to the last control panel must not exceed 800 meters in the case of 24AWG. NOTE When connecting control panels via DCH8, the total length of the cables to the final cont ol panel must be less than Owner’s Manual First, please carefully read the “IMPORTANT SAFETY INSTRUCTIONS” on the reverse side. Appendix Interruption 4Ω Failure Total impedance = 8Ω No sound Precautions for Rack Mounting This unit is rated for operation at ambient temperatures ranging from 0 to 40 degrees Celsius. When mounting the unit with other PA2120 unit(s) or other device(s) in an EIA standard equipment rack, internal temperatures can exceed the specified upper limit, esulting in impaired performance or failure. When rack mounting the unit, always observe the following requirements to avoid heat buildup: • When mounting the unit in a rack with devices such as power amplifiers that generate a significan amount of heat, leave more than 1U of space between the PA2120 and other equipment. Also either leave the open spaces uncovered or install appropriate ventilating panels to minimize the possibility of heat buildup. • To ensure sufficient ai flo , leave the rear of the rack open and position it at least 10 centimeters from walls or other surfaces. If the rear of the rack can’t be left open, install a commercially available fan or similar ventilating option to secure sufficient ai flo . If you’ve installed a fan kit, there may be cases in which closing the rear of the rack will produce a greater cooling effect. Refer to the rack and/or fan unit manual for details. NOTE • When the device is put into standby mode via the [REMOTE] connector, it is not possible to turn the power back PA2120 rear panel on by pressing the [z] button on the front panel, or by the auto-wake function with input signal detection. The power can only be turned on via the [REMOTE] connector. • When the device is put into mute mode via the [REMOTE] connector, the [z] button will flash in green. NOTE Refer to “Attaching Euroblock Plugs” for Euroblock plug installation. Specifications (MODE: STEREO) BMG source DCP AMP MODE = 3Ω AMP MODE = 4Ω AMP MODE = 8Ω AMP MODE = 70V/120W AMP MODE = 100V/120W AMP MODE = 70V/200W AMP MODE = 100V/200W Amplifier type (Output circuitry) THD+N LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 3Ω, 4Ω, 8Ω LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/120W LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/200W Output Power (20msec Burst, THD+N=1%) ■ When two-channel stereo is used: 120W x 2 (two-channel stereo) 100W x 2ch 120W x 2ch 100W x 2ch 120W x 2ch 120W x 2ch 200W x 1ch 200W x 1ch Class D Frequency Response LINE IN to SPEAKER OUT, 50Hz to 20kHz@1W 0dB, -3.0dB, +1.0dB AMP MODE = 3Ω, 4Ω, 8Ω LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W 0dB, -3.0dB, +1.0dB AMP MODE = 70V, 100V/120W LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W 0dB, -3.0dB, +1.0dB AMP MODE = 70V, 100V/200W LINE to THRU OUT, 0dB, -2.5dB, +1.0dB 20Hz-20kHz AC Power Requirement 100V, 120V, 230V-240V 50Hz/60Hz (*1) *1 It has confi med that it is working with ± 10% of the voltage of the rated supply voltage. ≤ 0.2% ≤ 0.2% Power Consumption ≤ 0.2% ENERGY STAR 1 Standby, default setting AMP MODE = All Idle AMP MODE = 3Ω, 4Ω, 8Ω Idle AMP MODE = 70V, 100V 1/8 Output, Pink noise AMP MODE = 4Ω 1/8 Output, Pink noise AMP MODE = 70V/120W ≤ 1W 15W 20W 60W 60W • It automatically enters into standby mode when no input signal is detected for 25 minutes in order to save power while not in use. • Amplifier e ficiency: 44% and mo e. • Less than 1W in standby. Operating temperature Storage temperature Dimensions (W x H x D, not including knob) Net Weight Included Accessories Optional accessories 0°C to +40°C -20°C to +60°C 480 x 44 x 351mm (18.90 x 1.73 x 13.82 inch) 4.8kg AC power cord (2.0m) x1, 3.5mm Euroblock plug (6pin) x1, 3.5mm Euroblock plug (3pin) x1, Owner’s Manual x1, Technical Specifications x Digital Control Panel (DCP1V4S-US/EU, DCP4V4S-US/EU, DCP4S-US/EU) * The contents of this manual apply to the latest specifications as of the printing date. Since amaha makes continuous improvements to the product, this manual may not apply to the specifications of your pa ticular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separatel sold accessories may not be the same in every locale, please check with your Yamaha dealer. European models Purchaser/User Information specified in EN55103-2:2009 Conforms to Environments: E1, E2, E3 and E4  Controls and Functions Front Panel 4 5 4 Rear Panel 5 PRECAUTIONS 8 A PLEASE READ CAREFULLY BEFORE PROCEEDING D Please keep this manual in a safe place for future reference. WARNING 2 1 [z] button (Standby/On) Switches the device mode between standby and on. On: Press the [z] button when in standby mode. The button lights in green to indicate that the device is on. Standby: Press and hold the [z] button for at least one second when the device is on. The button lights in orange to indicate that the device is in standby mode. The button lights in lime green for a few seconds while the status is switched between on and standby. NOTE • The device automatically enters standby mode when no input signal is detected for 25 minutes. The rear panel DIP switch can be set to enable the auto-wake function that turns the power on upon detecting an input signal. • Rapidly turning the unit on and off in succession can cause it to malfunction. After turning the unit off, wait for about 6 seconds before turning it on again. 3 3 1 6 5 Setting 6 AC IN connector Connect the supplied power cord. 8 6 Setting Low pass filter 150Hz Frequency correction tailored for Yamaha VXS series speakers Setting Frequency correction tailored for the Yamaha VXS10S/ VXS10ST subwoofer (45–150 Hz) Initialize (initializes the settings when turning on the power) Frequency correction tailored for Yamaha VXC series speakers Barrier strip type speaker output connectors. Output connectors A and B are available. Refer to “Connecting Speaker Cables” for the installation instructions. Sets the amplifier mode and speaker EQ to match the type of speakers that are connected. The setting change will be applied after carrying out a power cycle by pressing the [z] button on the front panel. DIP switch setting combinations are shown as follows. DIP switches 1, 2, and 3: Amplifier mode setup Sets the amplifier output power and impedance If the DIP switch settings do not match the actual speaker impedance or input power rating, the device may have poor performance, and it may even lead to malfunction or sound dropout. Always ensure that appropriate settings are chosen. 7 [SETUP] DIP switches Low pass filter 200Hz Resume (keeps the previous settings) NOTICE Caution • When connecting the power cord, connect the power cord to the connector and then plug it into an appropriate AC power outlet. • Before connecting or disconnecting the power cord, make sure that the device power is in standby mode. 5 Link on (SPEAKER A and SPEAKER B volume levels are both controlled via the [VOLUME A] knob) 9 [SPEAKER A] and [SPEAKER B] DIP switches Lights up when the limiter that prevents excessive output to [SPEAKER A] and [SPEAKER B] compresses the signal more than 3dB. Adjust the input and output levels as LIMIT indicators do not light. DIP switches 4, 5, and 6: Speaker EQ Sets the speaker EQ that corrects the output signal to match the type of speakers that are connected. High pass filter 150Hz Lights up when the output signal to [SPEAKER A] or [SPEAKER B] is -42dBFS (42dB lower than the maximum output) or higher. 5 [LIMIT] indicator C Off NOTE [SETUP] DIP switches other than the ones described above are not used. 4 [SIG] indicator B 4 8 [SPEAKERS] output terminals 1 2 3 Set the following functions of the device. The setting change will be applied after carrying out a power cycle by pressing the [z] button on the front panel. DIP switch setting combinations are shown as follows. Setting Amplifier output 120W, High-impedance 100V Amplifier output 120W, High-impedance 70V Amplifier output 200W, High-impedance 100V, Output only from [SPEAKERS] output terminal A DIP switch 1: Panel lock Set whether to lock knobs and controls on the panel. Amplifier output 200W, High-impedance 70V, Output only from [SPEAKERS] output terminal A Setting Amplifier output 100W, Low-impedance 8Ω or more Panel lock off (controls are enabled) Amplifier output 120W, Low-impedance from 4Ω to less than 8Ω Panel lock on (controls are disabled) 0 [DCP] connector Allows you to connect up to two DCP1V4S, DCP4S, or DCP4V4S Yamaha Digital Control Panels. For more information regarding the connection method, refer to “Connecting a Control Panel.” A [REMOTE] connector A Euroblock 3-pin plug can be inserted to remotely carry out control such as muting all channels or putting the device in and out of standby mode. For more information, refer to “Using the [REMOTE] Connector (Euroblock 3-pin).” B [THRU OUT] jacks RCA type line output jacks (unbalanced output). Output jacks A and B are available. The unaltered audio signal input from the [INPUT] connectors is output at the line level. These jacks can be used to connect an additional amplifier when the number of speakers is too much for this device to handle alone. C [INPUT] jacks/connectors RCA type and Euroblock 3-pin line input jacks/connectors (RCA: unbalanced; Euroblock 3-pin: balanced). Two channels (A and B) are available. Connect the line output connector of an external device. D [MODE] switch Sets the method in which input signals from [INPUT A] and [INPUT B] are sent as output to the [SPEAKERS] output terminals. Switch INPUT A output destination INPUT B output destination STEREO A B MONO Output to A and B with INPUT A and INPUT B signals mixed as mono A and B PARALLEL Muted Amplifier output 100W, Low-impedance from 3Ω to less than 4Ω DIP switches 3/ 4: Auto-wake Enable the function where the device automatically turns on from standby mode upon detection of an input signal. 4 0 Link off (SPEAKER A and SPEAKER B volume levels are independently controlled) Two-band equalizer used to adjust the tone of the output signal to [SPEAKER A] and [SPEAKER B]. They can be adjusted with a tool such as a screwdriver. 3 9 DIP switch 8: DCP setup When turning on the power, this sets whether resuming the settings of connected control panels or initializing. Used to adjust [SPEAKER A] and [SPEAKER B] output levels. 1 7 DIP switch 5: A - B volume link Sets whether SPEAKER A and SPEAKER B volume is linked. When linked, the volume for both speakers can be controlled with the [VOLUME A] knob. 2 [VOLUME A] and [VOLUME B] knobs 3 [BASS] and [TREBLE] controls 2 Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/power cord • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Only use the voltage specified as cor ect for the device. The required voltage is printed on the name plate of the device. • Use only the supplied power cord/plug. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. • When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the device will not be disconnected from the power source. When installing in a rack, connect an AC power strip to make power on/off operations easier and more convenient. • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock, damage to the device(s), or even fi e. Do not open • This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified amaha service personnel. Water warning • Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Never insert or remove an electric plug with wet hands. Hearing loss • Avoid setting all equalizer controls and volume controls to their maximum. Depending on the condition of the connected devices, doing so may result in feedback that can cause hearing loss and damage the speakers. • Do not use speakers for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • When turning on the AC power in your audio system, always turn on the device LAST, to avoid hearing loss and speaker damage. When turning the power off, the device should be turned off FIRST for the same reason. Fire warning • Do not place any burning items or open flames near the device, since they may cause a fi e. If you notice any abnormality • If any of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. – The power cord or plug becomes frayed or damaged. – Unusual smells or smoke are emitted. – Some object has been dropped into the device. – There is a sudden loss of sound during use of the device. – Cracks or other visible damage appear on the device. Then have the device inspected or repaired by qualified Yamaha service personnel. • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified amaha service personnel. Output muted Setting Auto-wake function on Auto-wake function on. Only when the system is switched from AC off to standby mode due to insertion of the AC plug, or put into standby mode by the auto-standby function. Auto-wake function off CAUTION NOTE The auto-wake function is completely disabled if the device has been put into standby mode through operation via the [REMOTE] connector. Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/power cord • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Troubleshooting Symptom The power does not turn on. The power turns off. Cause The power cord is disconnected. The protection function of the device is activated. The [S] and [G] pins of [REMOTE] connector are shorted. The auto-power-off function has activated. The power automatically turns on. The auto-wake function has activated. No sound is heard. The volume is lowered too much with the [VOLUME A] or [VOLUME B] knobs. No audio signal is being input. Zone selection is not appropriate. Zone B is being used while the amplifier output is set to 200W. The settings via a control panel are retained. The volume is low. The sound is distorted. The setting does not change even when turning the [VOLUME] knob. The stereo source connected to the INPUT is not providing a valid stereo signal. The stereo source connected to the INPUT is not being played correctly in each zone. DIP switch settings are not applied to the device. The sound drops out, and the [z] button and [LIMIT] indicator flash three times. The [z] button and [LIMIT] indicator continue to flash. The sound goes off. The device is set to low-impedance connection; however, speakers with highimpedance input have been connected. The input level from an external device is too high. The EQ level is too high. The panel is locked. Solution Connect the power cord. Pull out the power cord to turn off the power, and make sure the connection is secure. Wait several minutes, and then turn on the power again. Be sure to install the device in a location not subject to high temperatures, such as a shaded, well-ventilated place. Use the controller connected to the [REMOTE] connector to turn on the power. When there is no input signal for 25 minutes, the system automatically switches to standby mode. This function cannot be disabled. The auto-wake function is turned on by default. If you wish to turn it off, set [SETUP] DIP switches 3 and 4 to their downward positions while the system is in standby mode. Then, turn the power on by the [z] button. Turn the applicable knob to the right. Check the output signal from an external device that has been connected. Check the [MODE] switch setting of [INPUT]. When the amplifier output is set to 200W, there is no signal output from zone B. To initialize the settings, switch the [SETUP] DIP switch 8 to the downward position, then use the [z] button to reset the device. Match the impedance settings of this device and the connected speakers. The [MODE] switch is not set to STEREO. Adjust the output level of the external device. Use a tool such as a screwdriver to adjust the [BASS] and [TREBLE] controls on the front panel. To turn off the panel lock, switch all [SETUP] DIP switches 1 and 2 to the upward position, then use the [z] button to reset the device. Set the [MODE] switch to STEREO. The [MODE] switch is not set to MONO. Set the [MODE] switch to MONO. The [z] button has not been used to turn the device on. Changes to DIP switch settings are only applied after the device has been turned on by the [z] button. They are not applied if the power is turned on by the auto-power-on function, or by control via the [REMOTE] connector. Use the [z] button on the front panel to turn the device on. Match the impedance setting and the input rating setting of this device and the speakers. The device is set to high-impedance connection; however, speakers with lowimpedance input have been connected or too many speakers are connected. When the device is set to low-impedance connection, the total impedance of the connected speakers is less than the impedance setting of this device. The speaker cable is shorted. The internal temperature of the device is extremely high. FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not exp essly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Match the impedance settings of this device and the connected speakers. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s Inspect the connection of the speaker cables. Pull out the power cord, leave the device at a well-ventilated place, and turn the device back on several minutes later. Heat dissipation slits are covered or the device is placed in a confined place with The protection function of the device is activated. Check the installation location and surrounding environment. Be poor ventilation. sure to install the device in a location not subject to high temperatures, such as a shaded, well-ventilated place. The device settings do not match speaker impedance. The protection function of the device is activated. Match the impedance settings of this device and the connected speakers. Loud sound that exceeds the performance specifications of the device is continually Lower the volume. generated. • Refer also to the Yamaha Pro Audio website that provides a FAQ (a list of frequently asked questions, with answers). http://www.yamahaproaudio.com/ • If taking the above steps does not solve the problem, contact your Yamaha dealer for repair. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. 2 (class B) Information for Users on Collection and Disposal of Old Equipment Location • Do not place the device in an unstable position where it might accidentally fall over and cause injuries. • Do not block the vents. This device has ventilation holes at the top/sides to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fi e. • When attempting to dissipate heat on the device, when installing it: – Do not cover it with any cloth. – Do not install it on a carpet or rug. – Make sure the top surface faces up; do not install on its sides or upside down. – Do not use the device in a confined, poorly-ventilated location. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fi e. Make sure that there is adequate space around the device: at least 10cm above, 10cm at the sides and 10cm behind. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. • Before moving the device, remove all connected cables. • If the device is mounted in an EIA standard rack, carefully read the section “Precautions for Rack Mounting” on page 1. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), malfunction, or even fi e. Connections • Before connecting the device to other devices, turn off the power for all devices. Also, before turning the power of all devices on or off, make sure that all volume levels are set to the minimum. Failing to do so may result in electric shock, hearing loss, or equipment damage. • Use only speaker cables for connecting speakers to the speaker jacks. Use of other types of cables may result in fi e. Maintenance • Remove the power plug from the AC outlet when cleaning the device. Handling caution • Do not touch or carry this device until it returns to normal temperature, if the device has become excessively hot during use or after using immediately. Prolonged contact may cause low-temperature burns. • Do not insert your fingers or hands in any gaps or openings on the device (vents, panel, etc.). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, panel, etc.) If this happens, immediately turn off the power unplug the power cord from the AC outlet, and have the device inspected by qualified amaha service personnel. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors to prevent injuries. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling and maintenance • Do not use the device in the vicinity of a TV, radio, AV equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise. • Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components. • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. • When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical impregnated wiping cloths. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. • Do not use this device for any purpose other than driving loudspeakers. • Always turn the power off when the device is not in use. • Even when the [(z)] (Standby/On) switch is in standby status (power lamp is off/ display is off), electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. Information About this manual • The illustrations as shown in this manual are for instructional purposes only. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. OBSERVERA! Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget, även om själva apparaten har stängts av. ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en stikkontakt, som er tændt — også selvom der er slukket på apparatets afbryder. VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. (standby) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH : NEUTRAL BLUE BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the or colored GREEN or letter E or by the safety earth symbol GREEN-and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) Explanation of Graphical Symbols The lightning flash with ar owhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (UL60065_03) For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. CANADA NORTH AMERICA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col. San José Insurgentes, Delegación Benito Juárez, México, D.F., C.P. 03900 Tel: +52-55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila Olímpia – CEP 04551-010 – São Paulo/SP, Brazil Tel: +55-11-3704-1377 ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK, Buenos Aires, Argentina Tel: +54-11-4119-7000 VENEZUELA Yamaha Musical de Venezuela, C.A. AV. Manzanares, C.C. Manzanares Plaza, Piso 4, Oficina 0401, Baruta, Caracas, Venezuela Tel: +58-212-943-1877 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Edif. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, República de Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: +44-1908-366700 GERMANY Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH, Rellingen, Branch Switzerland in Zürich Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: +41-44-3878080 AUSTRIA/BULGARIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 POLAND/LITHUANIA/LATVIA/ESTONIA Yamaha Music Europe GmbH Sp.z o.o. Oddzial w Polsce ul. Wrotkowa 14, 02-553 Warsaw, Poland Tel: +48-22-880-08-88 PA41 MALTA ASIA Olimpus Music Ltd. Valletta Road, Mosta MST9010, Malta Tel: +356-2133-2093 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 INDIA NETHERLANDS/BELGIUM/ LUXEMBOURG FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activités de Pariest, 77183 Croissy-Beaubourg, France Tel: +33-1-6461-4000 ITALY Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020, Lainate (Milano), Italy Tel: +39-02-93577-1 SPAIN/PORTUGAL Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: +86-400-051-7700 Yamaha Music India Private Limited Spazedge Building, Ground Floor, Tower A, Sector-47, Gurgaon- Sohna Road, Gurgaon-122002, Haryana, India Tel: +91-124-485-3300 INDONESIA PT. Yamaha Musik Indonesia (Distributor) Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: +62-21-520-2577 KOREA Yamaha Music Korea Ltd. 8F, Dongsung Bldg. 21, Teheran-ro 87-gil, Gangnam-gu, Seoul, 135-880, Korea Tel: +82-2-3467-3300 Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17,200, 28231 Las Rozas de Madrid, Spain Tel: +34-91-639-88-88 MALAYSIA Philippos Nakas S.A. The Music House 19th klm. Leof. Lavriou 190 02 Peania – Attiki, Greece Tel: +30-210-6686168 SINGAPORE Yamaha Music Europe GmbH Germany filial Scandinavia JA Wettergrensgata 1, 400 43 Göteborg, Sweden Tel: +46-31-89-34-00 TAIWAN Yamaha Music Denmark, Fillial of Yamaha Music Europe GmbH, Tyskland Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark Tel: +45-44-92-49-00 THAILAND GREECE SWEDEN/FINLAND/ICELAND DENMARK NORWAY Yamaha Music Europe GmbH Germany Norwegian Branch Grini Næringspark 1, 1361 Østerås, Norway Tel: +47-6716-7800 RUSSIA Yamaha Music (Russia) LLC. Room 37, entrance 7, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: +7-495-626-5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 MIDDLE EAST TURKEY Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz Böl. No:3, Sanyer Istanbul, Turkey Tel: +90-212-999-8010 CYPRUS Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 Yamaha Music (Malaysia) Sdn. Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: +60-3-78030900 Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: +65-6740-9200 Yamaha Music & Electronics Taiwan Co.,Ltd. 2F., No.1, Yuandong Rd. Banqiao Dist. New Taipei City 22063, Taiwan Tel: +886-2-7741-8888 Siam Music Yamaha Co., Ltd. 3, 4, 15, 16th Fl., Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: +66-2215-2622 VIETNAM Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-8-3818-1122 OTHER ASIAN COUNTRIES Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Vic. 3006, Australia Tel: +61-3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 OTHER COUNTRIES Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 (3 wires) In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan. In Norway: Apparatet må tilkoples jordet stikkontakt. In Sweden: Apparaten skall anslutas till jordat uttag. The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the top of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.com/ (class I hokuo) 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. (class b korea) Model No. Serial No. (rear_en_01) Manual Development Department © 2016 Yamaha Corporation Published 02/2016 KSHD-A0 Printed in China