Yamaha A8D Manual de usuario

Yamaha
Marca
Yamaha
Modelo
A8D
Tipo
Manual de usuario
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 1
Nio
500
-
D
16
AUDIO INTERFACE
Nio
500
-
A
16
AUDIO INTERFACE
Nio
500
-
A8D8
AUDIO INTERFACE
Operation Manual
Benutzerhandbuch
Fonctions Détaillées
Manual de Operaciones
Manuale Operativo
Руководство пользователя
JA
ZH
RU
IT
ES
FR
DE
EN
NUAGE I/O
(
16
D
)
NUAGE I/O
(
16
A
)
NUAGE I/O
(
8
A
8
D
)
EnglishDeutschFrançaisEspañolItalianoРусский
2 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of this
product in a residential environment will not result in harmful
interference with other electronic devices. This equipment gen-
erates/uses radio frequencies and, if not installed and used
according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic
devices. Compliance with FCC regulations does not guarantee
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
that interference will not occur in all installations. If this product
is found to be the source of interference, which can be deter-
mined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America, Elec-
tronic Service Division, 6600 Orangethorpe Ave, Buena Park,
CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Audio Interface
Model Name : Nio500-D16/Nio500-A16/Nio500-A8D8
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
(FCC DoC)
이 기기는 가정용(B급) 전자파적합기기로서 주로
가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수 있습니다.
(class b korea)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the fol-
lowing code:
GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals
in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by
the safety earth symbol or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
(3 wires)
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 3
The above warning is located on the top of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
4 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
Contents
PRECAUTIONS .....................................................................................5
NOTICE .............................................................................................................. 6
Information.......................................................................................................... 6
Introduction ..........................................................................................7
A Message from the Development Team........................................................... 7
Included Accessories......................................................................................... 7
Items to Have Ready .......................................................................................... 7
Precautions for Rack Mounting .......................................................................... 8
Connection between the Device and a Computer ............................................. 8
How to Read the Manual .................................................................................... 8
About Dante..........................................................................................9
Overview............................................................................................................. 9
Connection with Dante Enabled Devices........................................................... 9
Setup ...................................................................................................10
Overall Process ................................................................................................ 10
Connection between the Device and a Computer ........................................... 10
Setting up the Power Supply ............................................................................ 11
Configuring the Audio Routing of the Dante Network ...................................... 11
Installing TOOLS for NUAGE............................................................................ 11
Configuring the Workgroup on NUAGE ........................................................... 11
Description of the Device ..................................................................12
Front Panel ....................................................................................................... 12
Rear Panel ........................................................................................................ 14
Description of the Software Programs.............................................17
NUAGE I/O Setup............................................................................................. 17
NUAGE Workgroup Manager........................................................................... 19
Troubleshooting.................................................................................21
Appendix.............................................................................................21
Firmware Updates ............................................................................................ 21
Specifications ....................................................................at the end of the book
Pin Assignment..................................................................at the end of the book
Dimensions........................................................................at the end of the book
Block Diagrams .................................................................at the end of the book
GNU GENERAL PUBLIC LICENSE ...................................at the end of the book
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 5
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you purchased,
the included power cord may not be compatible. Please check with your Yamaha
dealer.
• Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
• This device contains no user-serviceable parts. Do not open the device or
attempt to disassemble the internal parts or modify them in any way. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place on it any containers (such as vases, bottles or glasses) containing
liquids which might spill into any openings. If any liquid such as water seeps
into the device, turn off the power immediately and unplug the power cord from
the AC outlet. Then have the device inspected by qualified Yamaha service
personnel.
• Never insert or remove an electric plug with wet hands.
• Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
• When one of the following problems occur, immediately turn off the power
switch and disconnect the electric plug from the outlet. Then have the device
inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• Do not place the device in an unstable position where it might accidentally fall
over.
• Do not block the vents. This device has ventilation holes at the sides to prevent
the internal temperature from becoming too high. In particular, do not place the
device on its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or even fire.
• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the front-panel power switch can be
easily turned ON/OFF. If some trouble or malfunctions occurs, immediately turn
off the power switch and disconnect the plug from the outlet.
• If the device is mounted in an EIA standard rack, carefully read the section
“Precautions for Rack Mounting” on page 8. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), malfunction, or even
fire.
• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
• Remove the power plug from the AC outlet when cleaning the device.
Power supply/Power cord
Do not open
Water warning
Fire warning
If you notice any abnormality
Power supply/Power cord
Location
Connections
Maintenance
PA_en_1 1/2
6 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
• Do not insert your fingers or hands in any gaps or openings on the device
(vents, etc.).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device (vents, etc.) If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
European Models
Inrush Current based on EN 55103-1:2009
2.0 A (on initial switch-on)
2.0 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
NOTICE
To avoid the possibility of malfunction/ damage to the
product, damage to data, or damage to other property, follow
the notices below.
Handling and Maintenance
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices.
Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or
damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic
changes in ambient temperature — when the device is
moved from one location to another, or air conditioning is
turned on or off, for example. Using the device while
condensation is present can cause damage. If there is
reason to believe that condensation might have occurred,
leave the device for several hours without turning on the
power until the condensation has completely dried out.
• Always turn the power off when the device is not in use.
Information
About copyrights
Copying of the commercially available musical data
including but not limited to MIDI data and/or audio data is
strictly prohibited except for your personal use.
About this manual
• The illustrations and LCD screens as shown in this manual
are for instructional purposes only, and may appear
somewhat different from those on your device.
• Windows is a registered trademark of Microsoft
®
Corporation in the United States and other countries.
• Apple, Mac and Macintosh are trademarks of Apple Inc.,
registered in the U.S. and other countries.
• The company names and product names in this manual
are the trademarks or registered trademarks of their
respective companies.
• To view PDF files, you will need to install Adobe Reader on
your computer. You can download the latest Adobe Reader
at the following website.
http://www.adobe.com
About this product
The input/output level (Max. before clip) specification can be
customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will
be charged for this procedure.) For details, contact your
Yamaha dealer.
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the device, or data that is lost or destroyed.
Handling caution
PA_en_1 2/2
The model number, serial number, power requirements, etc.,
may be found on or near the name plate, which is at the top of
the unit. You should note this serial number in the space
provided below and retain this manual as a permanent record
of your purchase to aid identification in the event of theft.
Model No.
Serial No.
Introduction
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 7
Introduction
A Message from the
Development Team
Thank you for choosing a NUAGE series NUAGE I/O unit.
The NUAGE series is a professional music and sound
production system based around Steinberg Nuendo
digital audio workstation software.
Over the 20 years that have elapsed since Yamaha began
offering DM and O series digital consoles and other
equipment for post production and music production,
work schedules have become notably tighter with less
time available for individual projects. The NUAGE series
was created to respond to the deadline crunch with an
optimized working environment that provides
unprecedented efficiency as well as final quality.
The core of the system is Steinberg Nuendo, a DAW that
is acclaimed for its outstanding workflow efficiency and
sonic quality. The NUAGE MASTER (Ncs500-CT control
surface) and NUAGE FADER (Ncs500-FD control surface)
units were specifically developed to support and enhance
Nuendo operability. NUAGE MASTER provides a
comprehensive concentration of post production controls
in an efficient, easy-access layout. NUAGE FADER
integrates seamlessly with the Nuendo mixer window,
providing an intuitive hands-on extension to the software.
And then there’s the sound. NUAGE I/O audio interface
units have been designed to deliver the superior Nuendo
sound without compromise. Three models are currently
available: the Nio500-D16 with 16 channels of AES/EBU
input and output, the Nio500-A16 with 16 channels of
analog input and output, and the Nio500-A8D8 with a
combination of 8 channels of analog and 8 channels of
AES/EBU input and output. The NUAGE I/O units connect
to computers running Nuendo via the highly expandable
Dante digital audio protocol, allowing multiple NUAGE I/O
units to be flexibly incorporated in a wide variety of system
configurations. Monitoring latency is near zero for
comfortable, stress-free monitoring while recording, even
when multiple I/O units are used with cascaded monitor
buses. The development team was adamant that near-
zero latency would be essential to allow musicians and
artists to deliver their full creative and performance
potential.
Stability and dependability are essential in any
professional working environment. In addition to
minimizing latency, the DANTE ACCELERATOR (AIC128-
D audio interface card) used in conjunction with the
NUAGE I/O units offers stable, reliable communication
between I/O units and computer while allowing fast
recovery from any problems that do arise. You can
concentrate on the job at hand, secure in the knowledge
that you’ll be able to deliver great results on time.
Thanks to experience with the DM and O series, intensive
research, and invaluable feedback from our users, it is our
great pleasure to be able to deliver a new level of
production support in the NUAGE series. Our technology
is there to give you unrestricted creative freedom, and we
sincerely hope that the NUAGE series plays a role in your
growth and continued success.
The Yamaha NUAGE series development team.
Included Accessories
• Power cable
• Ferrite core
• Rubber stoppers (4)
• Operation Manual (this book)
NOTE
• Attach the ferrite core to prevent electromagnetic interference
when using the [CASCADE] connector. Fasten it to the
Ethernet cable near the [CASCADE OUT] connector.
• When using the unit on a slippery surface, attach the rubber
stoppers to the specified location on the bottom panel of this
device to prevent sliding.
Items to Have Ready
• Gigabit Ethernet Switch
A network switch that features various functions for
controlling and monitoring the network (such as QoS, the
ability to assign priority to data flows — e.g., clock
synchronization or audio transmission on certain data
circuits — and IGMP Snooping, the ability to filter
unnecessary multi-cast traffic) is recommended.
• Ethernet cable
A straight type (STP) of CAT5e or better is recommended.
•TOOLS for NUAGE
TOOLS for NUAGE is a software program which is
necessary when connecting the device to a computer.
When you install TOOLS for NUAGE, NUAGE Workgroup
Manager, NUAGE Extension, and NUAGE PT Bridge (Mac
only) will be installed. NUAGE Workgroup Manager is an
application that allows control over the devices and DAW
software applications as a Workgroup on NUAGE system.
NUAGE Extension is a program that allows you to link the
device with Nuendo (for versions which support the link
function). NUAGE PT Bridge is a program that allows you
to control Pro Tools (Mac only) using NUAGE FADER and
NUAGE MASTER (with the exception of certain functions).
TOOLS for NUAGE is available on the following website.
http://www.yamahaproaudio.com/downloads/
Introduction
8 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
Precautions for Rack
Mounting
This unit is rated for operation at ambient temperatures
ranging from 0 to 40 degrees Celsius. When mounting the
unit with other device(s) in an EIA standard equipment
rack, internal temperatures can exceed the specified
upper limit, resulting in impaired performance or failure.
When rack mounting the unit, always observe the
following requirements to avoid heat buildup:
• When mounting the unit in a rack with devices such as
power amplifiers that generate a significant amount of
heat, leave more than 1U of space between NUAGE I/O
and other equipment. Also either leave the open spaces
uncovered or install appropriate ventilating panels to
minimize the possibility of heat buildup.
• To ensure sufficient airflow, leave the rear of the rack
open and position it at least 10 centimeters from walls or
other surfaces. If the rear of the rack can’t be left open,
install a commercially available fan or similar ventilating
option to secure sufficient airflow. If you’ve installed a
fan kit, there may be cases in which closing the rear of
the rack will produce a greater cooling effect. Refer to
the rack and/or fan unit manual for details.
Connection between the
Device and a Computer
The device can be connected to a computer in one of two
ways: with or without the DANTE ACCELERATOR. Using
the DANTE ACCELERATOR gives you the added
advantages of lower latency, using more channels, and
utilization of a redundant network. The descriptions in this
manual assume you are using the DANTE
ACCELERATOR.
To connect the device and a computer with the DANTE
ACCELERATOR, install the Dante Controller to the
computer. Dante Controller is a software application that
allows configuration and audio routing of the Dante
network.
When not using the DANTE ACCELERATOR, install the
Dante Controller and DVS (Dante Virtual Soundcard).
Dante Controller is a software application that allows
configuration and audio routing of the Dante network. DVS
is a software application that uses the computer as a
Dante-enabled device.
Dante Controller is available on the following website.
http://www.yamahaproaudio.com/
DVS is commercially available on the following website.
http://www.audinate.com/
For details on Dante Controller and DVS, refer to the
respective manuals.
How to Read the Manual
Conventions
• Brackets and quotation marks
Brackets ([ ]) and quotation marks (“ ”) around names and
phrases in this manual are used to indicate the following.
• Windows or Mac
When the procedures or explanations are specific to only
one of the platforms, Windows or Mac, this is properly
indicated in the manual. When the platforms do not
appear, procedures or explanations are for both Windows
and Mac.
• Procedures
“” appears on some procedures in the manual. For
example, the string “Devices” “Device Setup”
“Control Panel” indicates that you should perform the
procedures in the following order.
1. Click the “Devices” menu.
2. Select the “Device Setup” option.
3. Click the “Control Panel” button.
• Keyboard Shortcuts
[Windows modifier key]/[Mac modifier key]+[key] shows
the shortcut keys. For example, [Ctrl]/[command]+[Z]
means “press [Ctrl] under Windows or [command] under
Mac, then press [Z].”
• Screens
This manual predominantly uses screenshots of Windows.
However, Mac screenshots are used when instructions of
the function apply only to the Mac. Also, this manual uses
screenshots of Nuendo 6. If you are using another version
of Nuendo, the actual screenshots might not be the same.
For details, refer to the Nuendo manuals (PDF) opened
from the “Help” menu.
Nuendo References
For brevity, the descriptions of Nuendo functions in this
manual have been kept simple and basic. For details on
Nuendo functions, refer to the Nuendo manuals (PDF)
opened from the “Help” menu.
Mark Indication target
[ ] • Buttons, switches, indicators, terminals, etc. on the
device.
• Keys on a computer keyboard.
“ ” • Menus, buttons, tabs, areas, windows, etc. on a
computer window or software window.
• Excerpts of messages, function names, terms in
the manual, etc.
About Dante
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 9
About Dante
Overview
This product features Dante technology as a protocol to
transmit audio signals. Dante is a network protocol
developed by Audinate. It is designed to deliver multi-
channel audio signals at various sampling and bit rates,
as well as device control signals over a Giga-bit Ethernet
(GbE) network. Dante also offers the following benefits:
• It transmits up to 512 in/512 out, for a maximum total of
1024 audio channels over a GbE network. (The NUAGE
I/O series can be accommodate up to eight devices,
128 in/128 out with a 24-bit resolution on a NUAGE
system.)
• Dante-enabled devices will automatically configure their
network interfaces and find each other on the network.
You can label Dante devices and their audio channels
with names that make sense to you.
• Dante uses high accuracy network synchronization
standards to achieve sample-accurate playback with
extremely low latency and jitter.
• Dante supports redundant connections via primary and
secondary circuits to defend against unforeseen
difficulties.
By taking advantages of these benefits, you can skip any
complicated procedures to automate connections and
setups of Dante-enabled devices, remotely control I/O
racks or amplifiers from a mixing console, or make multi-
track recordings to a DAW, such as Nuendo, installed on a
computer in the network. Visit Audinate website for more
details on Dante.
http://www.audinate.com/
More information on Dante-enabled devices are also
posted on the Yamaha Pro Audio website:
http://www.yamahaproaudio.com/
Connection with Dante
Enabled Devices
To connect with Dante enabled devices, use a star
connection or a daisy chain connection (enabled devices
only).
Star Connection
In a star connection, each device is connected to a
central network switch. Using a GbE-compatible network
switch enables you to configure a wide-band, large-scale
network. We recommend a network switch that features
various functions to control and monitor the network (such
as Qos, the ability to assign priority to data flows — e.g.,
clock synchronization or audio transmission on certain
data circuits.)
With this topology, it is common to configure a redundant
network so that an unexpected network problem will not
affect any audio or otherwise stable communications.
Redundant Network
A redundant network consists of two circuits, a primary
circuit and a secondary circuit. Normally, the network
operates on the primary circuit. However, if the primary
connection is broken, the secondary circuit will
automatically take over communications. Therefore, using
a redundant network with a star topology would increase
communication stability relative to a daisy chain network.
Daisy Chain Connection (enabled
devices only)
A daisy chain is a wiring scheme in which multiple
devices are connected together in sequence. This
connection method is suitable for a simple system with a
small number of devices.
However, if a large number of devices are connected, the
latency value must be increased. Also, if a connection is
broken in a daisy chain network, the signal flow is
interrupted at that point and no signal will be transferred
beyond that point.
Computer
Ethernet port
Network switch Network switch
Dante-enabled device
Dante-enabled device
Dante-enabled device
PRIMARY
PRIMARY
PRIMARY
SECONDARY
SECONDARY
SECONDARY
Computer
Ethernet port
Network switch
Dante-enabled device
Dante-enabled device
PRIMARY
PRIMARY
PRIMARY
SECONDARY
SECONDARY
Dante-enabled device
Setup
10 NUAGE I/O (16D )/ NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
Setup
Overall Process
This section explains how to set up the device for use with
the DANTE ACCELERATOR. Before setting up, make sure
that the following conditions are met.
• The DANTE ACCELERATOR installed to the computer
works properly.
• The Dante Controller has already been installed.
For details, refer to the DANTE ACCELERATOR manual.
1. Connect the device to a computer with a
Ethernet cable. “Connection between the
Device and a Computer” (page 10)
2. Connect the power cable then turn the
power on. “Setting up the Power Supply”
(page 11)
3. Configure the audio routing of the Dante
network with the Dante Controller.
“Configuring the Audio Routing of the Dante
Network” (page 11)
4. Install TOOLS for NUAGE. “Installing
TOOLS for NUAGE” (page 11)
5. Configure the Workgroup on NUAGE with
the NUAGE Workgroup Manager.
“Configuring the Workgroup on NUAGE”
(page 11)
Connection between the
Device and a Computer
Connect the devices and computer by using a star
connection or a daisy chain connection.
Star Connection
This section explains the connections when configuring a
redundant network.
1. Connect the Ethernet cable as shown below.
2. Set the [UNIT ID rotary switch] on the rear
panel to a unique ID.
3. Turn on (down) the [Dip switch] No.1 on the
rear panel.
NOTE
Redundant network operation may not be available on the
DANTE ACCELERATOR depending on its firmware version. Make
sure that the firmware version currently on the DANTE
ACCELERATOR supports a redundant network by checking the
following website.
Computer
Ethernet port
Network switch Network switch
PRIMARY
PRIMARY
PRIMARY
SECONDARY
SECONDARY
SECONDARY
PRIMARY SECONDARY
CASCADE
OUT
CASCADE
OUT
CASCADE IN
CASCADE IN
DANTE
ACCELERATOR
ID#1
ID#2
ID#3
Setup
NUAGE I/O (16D )/ NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 11
Daisy Chain Connection
1. Connect the Ethernet cable as shown below.
2. Set the [UNIT ID rotary switch] on the rear
panel to a unique ID.
3. Turn off (up) the [Dip switch] No.1 on the
rear panel.
Setting up the Power Supply
1. Insert one plug of the power cable into the
[AC IN] terminal on the device.
2. Insert the other plug of the power cable into
a proper AC wall outlet.
3. Turn on (|) the power.
WARNING
Only use the included power cable (or an equivalent
recommended by Yamaha). Using the wrong cable can result
in damage to the device or overheating.
CAUTION
Remove the plug of the power cable from the outlet when the
device is not be used for extended periods of time, or during
electrical storms.
Configuring the Audio Routing
of the Dante Network
1. Launch Dante Controller.
2. In the “Routing” tab on the “Network View”
window, set the audio routing by placing a
check mark at the intersection of the desired
devices.
To use the link function with Nuendo, set up as
follows.
• Set the sample rate and pull-up/pull-down
parameters on NUAGE I/O and DANTE
ACCELERATOR to the same settings.
• Join the inputs and outputs in the matrix. For
example, set channels 1 through 16 on NUAGE I/
O to channels 1 through 16 on DANTE
ACCELERATOR.
NOTE
For details on the Dante Controller, refer to the Dante
Controller manual.
Installing TOOLS for NUAGE
To install TOOLS for NUAGE, double-click the installer file
you have downloaded from the website. For details, refer
to the TOOLS for NUAGE installation guide.
Configuring the Workgroup on
NUAGE
To configure the Workgroup, open the NUAGE Workgroup
Manager then register the devices and DAW software
applications to the Workgroup. For details, refer to the
NUAGE Workgroup Manager manual (PDF). To open the
NUAGE Workgroup Manager manual, double-click the
NUAGE Workgroup Manager icon on the task tray
(Windows) or menu bar (Mac) for opening the window,
then click the “Manual” icon.
The setup is now completed.
Computer
Ethernet port
Network switch
PRIMARY
SECONDARYCASCADE OUT
CASCADE IN
DANTE
ACCELERATOR
ID#1
ID#2
ID#3
PRIMARY
SECONDARYCASCADE OUT
CASCADE IN
PRIMARY
PRIMARY
Description of the Device
12 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
Description of the Device
Front Panel
NUAGE I/O (16D)
NUAGE I/O (16A)
NUAGE I/O (8A8D)
Description of the Device
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 13
[INPUT level meter]
Indicates the input signal level of [ANALOG INPUT]
(page 16) or [AES/EBU] (page 16) on the rear panel.
[SAMPLE RATE indicator]
Indicates the sample rate of the device. To select the
sample rate of the device, use the NUAGE Workgroup
Manager (page 19).
[CLOCK indicator]
Indicates the word clock source of the device. To select
the word clock source of the device, use the NUAGE
Workgroup Manager (page 19).
The [SYSTEM indicator] indicates the system status of the
device on the Dante network.
The [SYNC indicator] indicates the synchronization status
of the device on the Dante network.
[SRC indicator]
Indicates the status of the SRC (sample rate converter),
on (lit) or off (unlit).
When you turn SRC on, even if the sample rate at which
the device is operating differs from the sample rate of the
audio signal input to the device, the SRC function
automatically converts the rate of the signal so that
playback will be correct. SRC is available on every two
adjacent channels. To turn SRC on/off, use the NUAGE
Workgroup Manager (page 19).
[OUTPUT level meter]
Indicates the output signal level of [ANALOG OUTPUT]
(page 16) or [AES/EBU] (page 16) on the rear panel.
[Power switch]
Turns the power on (I) and off ( ). The lamp lights when
the power is on, and is unlit when the power is off.
NOTICE
Rapidly turning the unit on and off in succession can cause it to
malfunction. After turning the unit off, wait for at least 6 seconds
before turning it on again.
Lamp Lighting level
Top (red) 0 dBFS
Second (orange) -3 dBFS or more
Third (orange) -14 dBFS or more
Bottom (green) -48 dBFS or more
Lamp Status Description
Left (green) Lit The device is working properly.
Left (green) Flashes (every
second)
The firmware updating is in
progress.
Right (red) Lit The memory on the device does not
work properly.
Right (red) Flashes (every
second)
The CPU on the device does not
work properly.
Lamp Status Description
Left (green) Lit The device is working as the slave
on the Dante network.
Left (green) Flashes (every
second)
The device is working as the master
on the Dante network.
Right
(orange)
Lit Synchronization with the Dante
network is in progress.
Right
(orange)
Flashes (every
second)
The device is not synchronized with
the Dante network.
Lamp Lighting level
Top (red) 0 dBFS
Second (orange) -3 dBFS or more
Third (orange) -14 dBFS or more
Bottom (green) -48 dBFS or more
Description of the Device
14 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
Rear Panel
NUAGE I/O (16D)
NUAGE I/O (16A)
NUAGE I/O (8A8D)
Description of the Device
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 15
[AC IN]
For connection to the power cable.
[Fan]
The electric fan for expelling heat and cooling the unit.
[UNIT ID rotary switch]
Sets the device ID on the Dante network. When
connecting multiple devices, set the ID on each device to
a different number. Note that you can only select the
device ID while the power is off. If you change this while
the power is on, the new device ID will not be applied.
[Dip switch]
Sets the device settings or initializes them. Note that you
can only select [Dip switch] while the power is off. If you
change this while the power is on, the settings will not be
applied.
[PRIMARY] (RJ-45 connector)
For connection to the Ethernet cable (CAT5e or better
recommended). This connector is for construction of the
Dante network, and is capable for input/output of sixteen
channels of audio. For details on how to connect the
devices, refer to “Setup” (page 10).
The lamp on this connector lights when the device is
communicating with the Dante network.
NOTE
• Use STP (shielded twisted pair) cable to prevent
electromagnetic interference. Make sure that the metal parts of
the plugs are electrically connected to the STP cable shield by
conductive tape or comparable means.
• Connect only Dante-compatible devices or GbE-compatible
devices (including a computer).
[SECONDARY] (RJ-45 connector)
The same as [PRIMARY]. However, the connection
configuration varies depending on the settings of [Dip
switch] (page 15). For details on how to connect the
devices, refer to “Setup” (page 10).
[SYSTEM LINK OUT] (BNC connector)
For connection to the BNC coaxial cable. When
connecting this connector to NUENDO SyncStation,
Nuendo and the devices maintain accurate
synchronization with each other.
[WORDCLOCK OUT] (BNC connector)
For connection to the BNC coaxial cable. This connector
outputs the word clock signal.
[WORDCLOCK IN] (BNC connector)
For connection to the BNC coaxial cable. This connector
receives the word clock signal.
[CASCADE OUT] (RJ-45 connector)
For connection to the Ethernet cable (CAT5e or better
recommended). This connector inputs and outputs
sixteen channels of audio for the direct monitoring. This is
useful when outputting the audio signal to another device
with near-zero latency. You can use this function with
Nuendo.
When connecting multiple devices, connect this to the
[CASCADE IN] terminals on other devices as shown.
Up to eight devices can be connected in this way.
NOTE
• Use a straight type (STP) cable of less than 3 meters.
• To use direct monitoring, complete “Setup” (page 10) then turn
on “Direct Monitoring” in the “Device Setup” menu on Nuendo.
• The device can input and output audio signals for direct
monitoring when the sample rate setting on the device is
96 kHz or lower. Direct monitoring is not supported for settings
of over 96 kHz.
[CASCADE IN] (RJ-45 connector)
Refer to [CASCADE OUT].
[Dip switch] Description
1 Selects whether [SECONDARY] (page 15) will
operate as a redundant network (page 9) or
daisy chain connection (page 9). [SECONDARY]
will operate as a redundant network when you
turn this on (down), and daisy chain connection
when you turn this off (up).
2 Initializes the device settings. Follow the steps
below.
1. Turn the power of the device off.
2. Turn [Dip switch 2] on (down).
3. Turn the power of the device on, then wait for
the [OUTPUT level meter] of the 16 channels to
flash at intervals.
4. Turn the power of the device off.
5. Turn [Dip switch 2] off (up).
6. Turn the power of the device on.
3 Not used. Turn it off (up) at any time.
4 Not used. Turn it off (up) at any time.
CASCADE OUT
CASCADE OUT
CASCADE IN
CASCADE IN
ID#1
ID#2
ID#3
Description of the Device
16 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
[ANALOG OUTPUT] (D-sub 25-pin connector)
For connection to a 25-pin D-sub analog cable. This
connector outputs eight channels of audio.
[ANALOG INPUT] (D-sub 25-pin connector)
For connection to a 25-pin D-sub analog cable. This
connector inputs eight channels of audio.
[AES/EBU] (D-sub 25-pin connector)
For connection to a 25-pin D-sub digital cable. This
connector inputs and outputs eight channels of audio.
Description of the Software Programs
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 17
Description of the
Software Programs
NUAGE I/O Setup
Overview
This software is for configuring the settings of the device
from Nuendo. To open this window, click the Nuendo
menu “Device” “NUAGE I/O Setup.”
NUAGE I/O Setup has the following two windows.
• Bass Management window
• ATT & Delay window
In the Bass Management window, you can separately
adjust the bass sound of the output signal from the device
in surround sound applications. In the ATT & Delay
window, you can adjust the level and delay of the output
signal from the device. To select the windows, click the
tabs on the upper side of the NUAGE I/O Setup window.
When you press the NUAGE Workgroup Manager button
on the upper right of the window, you can open the device
settings window opened from the NUAGE Workgroup
Manager. However, this is only available when launching
the NUAGE Workgroup Manager on the same computer.
NOTE
• To use these functions, complete “Setup” (page 10).
• To use the Bass Management function, create a surround
output bus (such as 5.1 channels) in the Nuendo menu
“Devices” “VST connection.” Also, assign the ports in one
NUAGE I/O to the ports of this output bus.
Controls and Functions
Bass Management Window
On/Off
Turns Bass Management on and off.
Presets
For selecting, storing, and deleting the preset.
The following presets are available in the default settings.
HPF1/2/3/4
Selects the type of high pass filter for each channel.
Preset
HPF
1/2/3/4
LPF1 LPF2
ATT
1/2
AMP
DVD LFE80Hz 80-12 80-24 80-24 0 +10
DVD LFE120Hz 80-12 120-42 80-24 0 +10
Movie LFE80Hz 80-12 80-24 80-24 -3 +10
Movie LFE120Hz 80-12 120-42 80-24 -3 +10
Bypass THRU THRU MUTE 0 0
Option Description
THRU The filter is not applied.
80-12 A Butterworth filter with a cutoff frequency of
80 Hz and -12 dB of attenuation.
80-12L A Linkwitz filter with a cutoff frequency of
80 Hz and -12 dB of attenuation.
80-24 A Butterworth filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
80-24L A Linkwitz filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
Description of the Software Programs
18 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
LPF1
Selects the type of low pass filter for the LFE channel.
LPF2
Selects the type of low pass filter for the LFE channel
which is sent the signal from each channel.
ATT1/2
Sets the attenuator for each channel. The setting range is
from 0dB to -12dB.
AMP
Sets the amplifier for the LFE channel. The setting range is
from 0dB to +12dB.
Block diagram
Indicates the position of each parameter in Bass
Management.
ATT & Delay Window
Presets
For selecting, storing, and deleting the preset.
Monitor
Selects the monitor for configuring the settings.
Mute on/off
Turns muting of the channel on and off.
Channel
Displays the channel.
Port
Displays the channel port.
ATT(dB)
Sets the attenuator/gain for speaker 1 and 2. The setting
range is from 0 dB to -12 dB, and the smallest unit is
0.1 dB.
DELAY(ms)
Sets the delay for the channel. The setting range is from 0
to 30 milliseconds, and the smallest unit is 0.02
milliseconds.
Option Description
THRU The filter is not applied.
80-24 A Butterworth filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
80-24L A Linkwitz filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
120-42 A Butterworth filter with a cutoff frequency of
120 Hz and -42 dB of attenuation.
Option Description
THRU The filter is not applied.
80-24 A Butterworth filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
80-24L A Linkwitz filter with a cutoff frequency of
80 Hz and -24 dB of attenuation.
MUTE The filter is muted.
Description of the Software Programs
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 19
NUAGE Workgroup Manager
Overview
This is a software application that allows control over the
devices and DAW software applications as a Workgroup
on NUAGE system. To open this window, double-click the
NUAGE Workgroup Manager icon on the task tray
(Windows) or menu bar (Mac).
This section provides only the descriptions regarding the
device settings on the NUAGE Workgroup Manager. For
details on the NUAGE Workgroup Manager, refer to the
corresponding manual (PDF) which can be opened from
the “Manual” icon.
You can configure the following device settings in the
NUAGE Workgroup Manager. However, the setting menu
will differ depending on the particular devices being used.
• Adjusting the trim of the analog input and output
signals.
• Selecting the level of the analog input signal.
• Selecting the word clock source.
• Turning the SRC (sample rate converter) of the digital
input signal on and off.
• Turning the dual wire on and off.
To configure these settings, use the “Property Window”
opened by clicking “Property” on the Workgroup area in
the Main window.
Controls and Functions
NUAGE I/O (16D)
Description of the Software Programs
20 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual
NUAGE I/O (16A)
NUAGE I/O (8A/8D)
Name
Displays the name of the device or DAW software. To
change this name, click “Property” on the Workgroup area
in the Main window.
Version
Displays the version. You can confirm the firmware version
in case of devices, or the version of NUAGE Extension in
the case of Nuendo, or the version of NUAGE PT Bridge in
the case of Pro Tools.
Update
Update the device’s firmware. For details, refer to the
NUAGE Firmware Update Guide.
MAC Address
Displays the MAC Address.
Word Clock Source
Selects the word clock source.
Input and output
Displays the input and output.
Dual Wire
Turns the Dual Wire function on and off. You can turn on
and off the Dual Wire by eight channels.
This function is available when the sample rate is set to
88.2, 96, 176.4, and 192 kHz, and also the SRC is turned
off.
SRC
Turns the sample rate converter on and off. This function
is only available when the Dual Wire is turned off.
Level
Selects the input level.
Trim
Adjusts the trim.
Troubleshooting
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 21
Troubleshooting
Power does not turn on.
• Is [Power switch] turned on?
• Is the power cable connected to a proper AC outlet?
• Is the power cable plug inserted all the way?
If the power still does not turn on, contact your Yamaha
dealer.
Device is not communicating with
Nuendo
• Is the Ethernet cable connected properly?
• Has “Installing TOOLS for NUAGE” (page 11) already
been completed?
• Has “Configuring the Workgroup on NUAGE” (page 11)
already been completed?
• Has “Configuring the Audio Routing of the Dante
Network” (page 11) already been completed?
• In case of connecting multiple devices, has the [UNIT
ID rotary switch] been set to a unique ID?
• Have the fire wall settings been set property?
Appendix
Firmware Updates
This product enables you to update the unit firmware to
improve operations, add functions, and correct possible
malfunctions. The following two types of firmware are
available for the unit.
•Unit’s firmware
• Dante module firmware
You must update each type of firmware separately. Details
on updating the firmware are available on the following
website:
http://www.yamahaproaudio.com/
For information on updating and setting up the unit,
please refer to the firmware update guide available on the
website.
NOTE
When you update Dante firmware on the unit, be sure to update
Dante firmware on other Dante-compatible devices connected to
the NUAGE I/O.
Specifications
ELECTRICAL CHARACTERISTICS
ANALOG INPUT CHARACTERISTICS
The input level (Max. before clip) specification can be customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will be
charged for this procedure.) For details, contact your Yamaha dealers.
ANALOG OUTPUT CHARACTERISTICS
The output level (Max. before clip) specification can be customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will be
charged for this procedure.) For details, contact your Yamaha dealer.
Sampling
Frequency
Internal
44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz
External
44.1kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
48kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
88.2kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
96kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
176.4kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
192kHz
+4.1667%/+0.1%/-0.1%/-4.0%
±200ppm
Analog Input/
Output
Frequency Response
±0.5dB, 20Hz – 20kHz, ref to the nominal output level @1kHz,
Input&Output Gain: 0dB, Input level +4dBu(typ)
THD+N
*1
Less than 0.005%, input to output, GAIN: 0dB
Dynamic Range
120dB typ., ADC
120dB typ., DAC
Crosstalk@1kHz
-100dB, CH1 – 16 , adjacent inputs
Input Terminals
Actual Load
Impedance
For Use With
Nominal
GAIN
Input level
Connector in
Console
Nominal
Max. before
clip
ANALOG INPUT 20kΩ (BAL) 150Ω Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB
Connector 25P
(Female)+12dB -10dBV (0.32 V) +10dBV (3.16 V)
10kΩ (UNBAL) 600Ω Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB
Connector 25P
(Female)+12dB -10dBV (0.32 V) +10dBV (3.16 V)
Output Terminals
Actual Source
Impedance
For Use With
Nominal
GAIN
Output level
Connector in
Console
Nominal
Max. before
clip
ANALOG OUTPUT 75Ω (BAL) 10kΩ Lines 0dB +4dBu (1.23 V) +24dBu (12.28V) D-SUB
Connector 25P
(Female)
DIGITAL INPUT CHARACTERISTICS
DIGITAL OUTPUT CHARACTERISTICS
DIGITAL INPUT & OUTPUT CHARACTERISTICS
CONTROL I/O CHARACTERISTICS
General Specifications
*1 These characteristics are measured with A-weighting filter and/or 30kHz LPF.
*2 Hi Speed CML
*3 AES-3id
Terminal Format Data length Level Connector in Console
AES/EBU AES/EBU 24bit RS422 D-SUB Connector 25P (Female)
Terminal Format Data length Level Connector in Console
AES/EBU AES/EBU
Professional use
24bit RS422 D-SUB Connector 25P (Female)
Terminal Format Data length Level Connector in Console
Primary/Secondary Dante 24bit 1000Base-T RJ-45 x 2
Cascade - 32bit LVDS
*2
RJ-45 x 2
Terminal Format Level Connector in Console
WORD CLOCK IN - TTL/75Ω terminated BNC Connector
OUT - TTL/75Ω BNC Connector
System Link Out - 1.0±0.2Vp-p/75Ω
*3
BNC Connector
Power Requirements
(wattage)
Nio500-D16: 51W
Nio500-A16: 51W
Nio500-A8D8: 51W
Power Requirements
(voltage and hertz)
US/Canada: 120V 60Hz
Japan: 100V 50/60Hz
China: 110 – 240V 50/60Hz
Korea: 220V 60Hz
Other: 110 – 240V 50/60Hz
Temperature Range
Operating temperature range: 0 – 40°C
Storage temperature range: -20 – 60°C
Dimensions (W x H x D)
480 x 88 x 369 mm
Net Weight
Nio500-D16: 6.4kg
Nio500-A16: 6.7kg
Nio500-A8D8: 6.7kg
Included Accessories
Power cable, Ferrite core, Ruber stoppers (4), Operation Manual
Pin Assignment
Analog Input
Analog Output
Digital Input & Output
Specifications and descriptions in this manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale,
please check with your Yamaha dealer.
Die technischen Daten und Beschreibungen in diesem Handbuch dienen nur der Information. Yamaha Corp. behält sich das Recht vor,
Produkte oder technische Daten jederzeit ohne vorherige Ankündigung zu ändern oder zu modifizieren. Da die technischen Daten, das
Gerät selbst oder das Zubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifelsfall bitte mit Ihrem Yamaha-Händler in
Verbindung.
Les caractéristiques techniques et les descriptions figurant dans le présent manuel sont fournies à titre d'information uniquement. Yamaha
Corp. se réserve le droit de changer ou modifier les produits et leurs caractéristiques techniques à tout moment sans aucun préavis. Les
caractéristiques techniques, le matériel ou les options peuvent varier selon le lieu de distribution. Veuillez par conséquent vous renseigner
auprès de votre revendeur Yamaha.
Las especificaciones y descripciones incluidas en este manual tienen una finalidad meramente informativa. Yamaha Corp. se reserva el
derecho de cambiar o modificar los productos o especificaciones en cualquier momento y sin previo aviso. Puesto que las especificaciones,
los equipos o las opciones podrían no ser las mismas en todos los casos, le rogamos consulte a su distribuidor de Yamaha.
Le specifiche e le descrizioni riportate in questo manuale sono fornite a scopo puramente informativo. Yamaha Corp. si riserva il diritto di
modificare prodotti o specifiche in qualsiasi momento senza preavviso. Poiché le specifiche tecniche, le apparecchiature e i componenti
opzionali potrebbero variare a seconda del Paese in cui viene distribuito il prodotto, controllare queste informazioni presso il proprio
rivenditore Yamaha.
Технические характеристики и описания приводятся в данном руководстве исключительно в справочных целях. Корпорация
Yamaha Corp. оставляет за собой право изменять или модифицировать продукты и технические характеристики в любое время без
предварительного уведомления. Так как технические характеристики, оборудование и компоненты могут различаться в разных
странах, обратитесь за информацией к местному представителю корпорации Yamaha.
本说明书中的技术规格及介绍仅供参考。Yamaha公司保留随时更改或修订产品或技术规格的权利，若确有更改，恕不事先通知。技术规格、设备或选
购件在各个地区可能均会有所不同，因此如有问题，请和当地Yamaha经销商确认。
Signal Input Ch Open GND
1
(9)
2
(10)
3
(11)
4
(12)
5
(13)
6
(14)
7
(15)
8
(16)
Pin Hot 24 10 21 7 18 4 15 1 13 2, 5, 8, 11, 16, 19, 22,
25
Cold1223920617314
Signal Output Ch Open GND
1
(9)
2
(10)
3
(11)
4
(12)
5
(13)
6
(14)
7
(15)
8
(16)
Pin Hot 24 10 21 7 18 4 15 1 13 2, 5, 8, 11, 16, 19, 22,
25
Cold1223920617314
Signal Data In Ch Data Out Ch Open GND
1-2
(9-10)
3-4
(11-12)
5-6
(13-14)
7-8
(15-16)
1-2
(9-10)
3-4
(11-12)
5-6
(13-14)
7-8
(15-16)
PinHot123456789, 1110, 12, 13, 22, 23, 24,
25
Cold 14 15 16 17 18 19 20 21
113
1425
Dimensions
NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D)
480
88 358
430
11
369
Block Diagrams
OUTPUT
1-16
[DANTE]
(OUTPUT 1-16)
[DANTE]
(INPUT 1-16)
INPUT
1-16
METER
METER
16
NUAGE I/O (16A)
[ANALOG 1-8]
[ANALOG 9-16]
INPUT
1-8
INPUT
9-16
OUTPUT
1-8
[ANALOG 1-8]
NUAGE I/O (16D)
8
TRIM
8
8
TRIM
NUAGE I/O (8A8D)
LEVEL
+4dBu/-10dBV
OUTPUT
9-16
[ANALOG 9-16]
8
TRIM
[AES/EBU 1-8]
[AES/EBU 9-16]
INPUT
1-8
INPUT
9-16
8
8
OUTPUT
1-8
[AES/EBU 1-8]
8
OUTPUT
9-16
[AES/EBU 9-16]
8
[ANALOG 1-8]
INPUT
1-8
OUTPUT
1-8
[ANALOG 1-8]
8
TRIM
8
TRIM
LEVEL
+4dBu/-10dBV
[AES/EBU 9-16]
INPUT
9-16
8
OUTPUT
9-16
[AES/EBU 9-16]
8
16
NUAGE I/O — 176.4/192kHz
GNU GENERAL PUBLIC
LICENSE
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change
free software—to make sure the software is free for all its users. This
General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is
covered by the GNU Library General Public License instead.) You can
apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and charge
for this service if you wish), that you receive source code or can get it if
you want it, that you can change the software or use pieces of it in new
free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone
to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must give the recipients all the rights that you have.
You must make sure that they, too, receive or can get the source code.
And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and
(2) offer you this license which gives you legal permission to copy,
distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original,
so that any problems introduced by others will not reflect on the
original authors' reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent
must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed
under the terms of this General Public License. The “Program”, below,
refers to any such program or work, and a “work based on the
Program” means either the Program or any derivative work under
copyright law: that is to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without
limitation in the term “modification”.) Each licensee is addressed as
“you”.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running
the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether
that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any warranty; and give
any other recipients of the Program a copy of this License along with
the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion
of it, thus forming a work based on the Program, and copy and
distribute such modifications or work under the terms of Section 1
above, provided that you also meet all of these conditions:
• a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
• b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
• c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but does
not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the Program,
and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote
it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise
the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
• a) Accompany it with the complete corresponding machine-
readable source code, which must be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for
software interchange; or,
• b) Accompany it with a written offer, valid for at least three years,
to give any third party, for a charge no more than your cost of
physically performing source distribution, a complete machine-
readable copy of the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
• c) Accompany it with the information you received as to the offer
to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such
an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access
to copy from a designated place, then offering equivalent access to
copy the source code from the same place counts as distribution of the
source code, even though third parties are not compelled to copy the
source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is void,
and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and
all its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the
original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further
restrictions on the recipients' exercise of the rights granted herein. You
are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not
permit royalty-free redistribution of the Program by all those who
receive copies directly or indirectly through you, then the only way you
could satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public
license practices. Many people have made generous contributions to
the wide range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add
an explicit geographical distribution limitation excluding those
countries, so that distribution is permitted only in or among countries
not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and
conditions either of that version or of any later version published by the
Free Software Foundation. If the Program does not specify a version
number of this License, you may choose any version ever published
by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the
author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by
the two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New
Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it
free software which everyone can redistribute and change under these
terms.
To do so, attach the following notices to the program. It is safest to
attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found.
one line to give the program's name and an idea of what it does.
Copyright © yyyy name of author
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or (at
your option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software Foundation,
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and paper
mail.
If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright © year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type `show w'. This is free software, and you are welcome to
redistribute it under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than `show w' and
`show c'; they could even be mouse-clicks or menu items--whatever
suits your program.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your
program into proprietary programs. If your program is a subroutine
library, you may consider it more useful to permit linking proprietary
applications with the library. If this is what you want to do, use the GNU
Library General Public License instead of this License.
Note on source code distribution
For three years after the final factory shipment, you may request from
Yamaha the source code for any portions of the product which are
licensed under the GNU General Public License by writing to the
following address:
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
The source code will be provided at no charge; however, we may
require you to reimburse Yamaha for the cost of delivering the source
code to you.
• Note that we shall bear no responsibility whatsoever for any damage
arising from changes (additions/ deletions) made to the software for
this product by a third party other than Yamaha (or party authorized
by Yamaha).
• Note that re-use of source code released to the public domain by
Yamaha is unguaranteed, and Yamaha shall not bear any
responsibility whatsoever for the source code.
• The source code can be downloaded from the following address:
http://yamahaproaudio.com/
Hinweis für den Zugriff auf Quellcode
In einem Zeitraum von bis zu drei Jahren nach endgültiger
Auslieferung können Sie von Yamaha den Quellcode für alle Teile des
Produkts anfordern, die der allgemein-öffentlichen Lizenz (General
Public License) GNU unterliegen, indem Sie ein Schreiben an
folgende Adresse richten:
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
Der Quellcode wird kostenlos zur Verfügung gestellt; es kann jedoch
sein, dass wir Sie bitten, Yamaha für die durch die Lieferung
entstandenen Kosten zu entschädigen.
• Bedenken Sie bitte, dass wir keine Verantwortung für Schäden
übernehmen, die aus Änderungen (Hinzufügung/Löschung) an der
Software für dieses Produkt entstehen, die von Dritten außer
Yamaha selbst (oder von Yamaha hierfür autorisierten Parteien)
vorgenommen wurden.
• Bedenken Sie, dass die Wiederverwendung von Quellcode, der von
Yamaha an die Public Domain übergeben wurde, keiner Garantie
unterliegt und dass Yamaha keine Verantwortung für den Quellcode
übernimmt.
• Der Quellcode kann von der folgenden Adresse heruntergeladen
werden: http://yamahaproaudio.com/
Note concernant la distribution du code
source
Au cours des trois années qui suivent la sortie définitive d'usine, vous
pouvez demander à Yamaha le code source de toute partie du produit
fournie sous licence dans le cadre d'une licence GNU General Public
License en envoyant un courrier à l'adresse suivante :
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
Le code source vous sera fourni gratuitement. Nous pouvons toutefois
vous demander de rembourser à Yamaha les frais d'expédition du
code.
• Notez que nous déclinons toute responsabilité pour les dommages
résultant de modifications (ajouts/suppressions) apportées au
logiciel de ce produit par un tiers autre que Yamaha (ou une partie
autorisée par Yamaha).
• Notez que la réutilisation du code source distribué dans le domaine
public par Yamaha n'est pas garantie et que Yamaha décline toute
responsabilité pour le code source.
• Vous pouvez également télécharger le code source à l'adresse
suivante : http://yamahaproaudio.com/
Nota sobre la distribución del código fuente
Durante tres años tras la salida final de fábrica, puede solicitar a
Yamaha el código fuente de cualquier parte del producto para el que
se conceda licencia según la Licencia Pública General (GNU),
enviando solicitud escrita a:
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
El código fuente se proporcionará sin cargo alguno; sin embargo,
Yamaha podría solicitar el reembolso del coste de envío.
• Debe tenerse en cuenta que no admitiremos responsabilidad alguna
por cualesquiera daños que puedan derivarse de los cambios
(adiciones o eliminaciones) realizados en el software de este
producto por un tercero que no sea Yamaha (o alguien autorizado
por Yamaha).
• Asimismo, debe tenerse en cuenta que la reutilización del código
fuente que Yamaha hace de dominio público no tiene garantía
alguna, y Yamaha no asumirá responsabilidad respecto a este
código.
• El código fuente se puede descargar de la siguiente dirección:
http://yamahaproaudio.com/
Note sulla distribuzione del codice sorgente
Entro tre anni dalla consegna di fabbrica finale, è possibile richiedere
a Yamaha il codice sorgente di qualsiasi parte del prodotto fornita con
licenza GNU General Public License scrivendo al seguente indirizzo:
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
Il codice sorgente verrà fornito senza spese, tuttavia Yamaha
richiederà un rimborso per i relativo costi di spedizione.
• Yamaha non si assume alcuna responsabilità per eventuali danni
derivanti da modifiche (aggiunte/eliminazioni) effettuate al software
di questo prodotto da terze parti diverse da Yamaha (o da terze parti
autorizzate da Yamaha).
• Il riutilizzo del codice sorgente rilasciato come dominio pubblico da
parte di Yamaha non è garantito e Yamaha non si assume alcuna
responsabilità relativa al codice sorgente.
• È possibile scaricare il codice sorgente dal seguente indirizzo:
http://yamahaproaudio.com/
Замечание о распространении исходного
кода
В течение трех лет после отгрузки с завода можно запросить в
компании Yamaha исходный код для любой категории
программных продуктов, на которые распространяется
Универсальная общественная лицензия GNU, обратившись по
следующему адресу:
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA Corporation
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
Исходный код поставляется бесплатно, однако вас могут
попросить возместить корпорации Yamaha расходы по его
пересылке.
• Следует отметить, что корпорация не несет ответственности за
любой ущерб, возникший в результате изменений (дополнений/
удалений), произведенных в программном обеспечении для
данного продукта третьими лицами, не имеющими отношения к
корпорации Yamaha (или не являющимися уполномоченными
представителями корпорации Yamaha).
• Также следует отметить, что вторичное использование
исходного кода, выпущенного для публичного использования
корпорацией Yamaha, не является предметом гарантии и что
Yamaha не несет ответственности за любое использование
такого исходного кода.
• Исходный код можно загрузить с веб-сайта по адресу:
http://yamahaproaudio.com/
关于源代码分发的注意事项
在产品最终出厂后的3年内，您可以通过写信到以下地址向Yamaha索
取经GNU General Public License授权的本产品任何部分的源代码。
PA Marketing Group Marketing Department Pro Audio Division,
YAMAHA 公司
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN
虽然源代码是免费提供的，但是我们可能会向您收取源代码的运送费
用。
• 请注意，我们对于由Yamaha （或Yamaha授权单位）以外的第三方
对本产品的软件所进行的变动 （添加/删除）而造成的任何损失概不
承担责任。
• 请注意，Yamaha不保证公开发布的源代码能再次使用，Yamaha对
源代码概不承担责任。
• 源代码可从下列地址下载：
http://yamahaproaudio.com/
SJ/T 11363-2006
×
SJ/T 11363-2006
EU RoHS
(This product conforms to the RoHS regulations in the EU.)
(Dieses Produkt entspricht der RoHS-Richtlinie der EU.)
(Ce produit est conforme aux réglementations RoHS de l'UE.)
(Este producto cumple con los requisitos de la directiva RoHS en la UE.)
Pb Hg Cd Cr (VI)
PBB
PBDE
×
×
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should
not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service
or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct
method of disposal.
(weee_eu_en_01)
Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.
Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être
mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les déposer aux
points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC.
En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de précieuses
ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement inapproprié des déchets.
Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contacter votre
municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits.
[Pour les professionnels dans l'Union Européenne]
Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour plus d'informations.
[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]
Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et électroniques, veuillez
contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée.
(weee_eu_fr_01)
Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo
Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos
usados no deben ser mezclados con desechos hogareños corrientes.
Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables,
de acuerdo a su legislación nacional y las directivas 2002/96/EC.
Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo
sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.
Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de
gestión de residuos o el punto de venta en el cual usted adquirió los artículos.
[Para usuarios de negocios en la Unión Europea]
Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor información.
[Información sobre la Disposición en otros países fuera de la Unión Europea]
Este símbolo sólo es válido en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte por el
método correcto de disposición.
(weee_eu_es_01)
Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte
Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische Geräte
nicht mit dem normalen Haushaltsabfall entsorgt werden.
In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC bringen Sie alte Geräte bitte zur fachgerechten
Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.
Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern mögliche negative
Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten.
Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche Stadt- oder
Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.
[Information für geschäftliche Anwender in der Europäischen Unio]
Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.
[Entsorgungsinformation für Länder außerhalb der Europäischen Union]
Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder
Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.
(weee_eu_de_01)
Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura
Questo simbolo sui prodotti, sull’imballaggio e/o sui documenti che li accompagnano significa che i prodotti elettrici ed elettronici non
dovrebbero essere mischiati con i rifiuti domestici generici.
Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con la
Sua legislazione nazionale e le direttive 2002/96/CE.
Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla salute
umana e l'ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.
Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo
servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.
[Per utenti imprenditori dell'Unione europea]
Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni.
[Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea]
Questo simbolo è valid0 solamente nell'Unione Europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il rivenditore e
richieda la corretta modalità di smaltimento.
(weee_eu_it_01)
ADDRESS LIST
HEAD OFFICE Yamaha Corporation, Commercial Audio Business Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: +1-416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: +1-714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: +52-55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila
Olímpia – CEP 04551-010 – São Paulo/SP, Brazil
Tel: +55-11-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Edif. Torre Banco General, Piso 7, Urbanización
Marbella, Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: +44-1908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH, Branch
Switzerland in Thalwil
Seestrasse 18a, 8800 Thalwil, Switzerland
Tel: +41-44-3878080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Sp.z o.o. Oddzial w Polsce
ul. Wrotkowa 14, 02-553 Warsaw, Poland
Tel: +48-22-880-08-88
MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010, Malta
Tel: +356-2133-2093
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5b, 4133 AB Vianen, The Netherlands
Tel: +31-347-358040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activités de Pariest,
77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020, Lainate (Milano), Italy
Tel: +39-02-93577-1
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
19th klm. Leof. Lavriou 190 02 Peania – Attiki,
Greece
Tel: +30-210-6686168
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
JA Wettergrensgata 1, 400 43 Göteborg, Sweden
Tel: +46-31-89-34-00
DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe GmbH, Tyskland
Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark
Tel: +45-44-92-49-00
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, 1332 Østerås, Norway
Tel: +47-6716-7800
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7, Kievskaya street,
Moscow, 121059, Russia
Tel: +7-495-626-5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz
Böl. No:3, Sariyer Istanbul, Turkey
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
OTHER COUNTRIES
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: +86-400-051-7700
INDIA
Yamaha Music India Private Limited
P-401, JMD Megapolis, Sector-48, Sohna Road,
Gurgaon-122018, Haryana, India
Tel: +91-124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: +62-21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, Dongsung Bldg. 21, Teheran-ro 87-gil,
Gangnam-gu, Seoul, 06169, Korea
Tel: +82-2-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn. Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: +60-3-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: +65-6740-9200
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
2F., No.1, Yuandong Rd. Banqiao Dist.
New Taipei City 22063, Taiwan, R.O.C.
Tel: +886-2-7741-8888
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15, 16th Fl., Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: +66-2215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
VIC 3006, Australia
Tel: +61-3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
PA45
Manual Development Group
© 2012 Yamaha Corporation
Published 07/2016
ᬍ⠜
MWHD-D0
Printed in China
ZF63600
Yamaha Pro Audio global website:
http://www.yamahaproaudio.com/
Yamaha Downloads
http://download.yamaha.com/
䲙偀જФ఼䷇ડ˄Ё೑˅ᡩ䌘᳝䰤݀ৌ
Ϟ⍋Ꮦ䴭ᅝऎᮄ䯌䏃
1818
োѥ੠໻ॺ
2
ὐ
ᅶ᠋᳡ࡵ⛁㒓˖
4000517700
݀ৌ㔥ഔ˖
http://www.yamaha.com.cn
ॖৡ
:
䲙偀જ⬉ᄤ˄㢣Ꮂ˅᳝䰤݀ৌ
ॖഔ
:
∳㢣ⳕ㢣ᎲᏖ㢣Ꮂᮄऎ呓ቅ䏃
18
ো

Transcripción de documentos

English Deutsch Français NUAGE I/O (16D) Nio500-D16 NUAGE I/O (16A) Nio500-A16 NUAGE I/O (8A8D) Nio500-A8D8 Español AUDIO INTERFACE AUDIO INTERFACE Русский Operation Manual Benutzerhandbuch Fonctions Détaillées Manual de Operaciones Manuale Operativo Руководство пользователя Italiano AUDIO INTERFACE EN DE FR ES IT RU ZH NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual JA 1 FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620 714-522-9011 Audio Interface Nio500-D16/Nio500-A16/Nio500-A8D8 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC) 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. (class b korea) IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. (3 wires) 2 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (UL60065_03) NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 3 Contents PRECAUTIONS .....................................................................................5 NOTICE .............................................................................................................. 6 Information.......................................................................................................... 6 Introduction ..........................................................................................7 A Message from the Development Team........................................................... 7 Included Accessories......................................................................................... 7 Items to Have Ready .......................................................................................... 7 Precautions for Rack Mounting .......................................................................... 8 Connection between the Device and a Computer ............................................. 8 How to Read the Manual .................................................................................... 8 About Dante..........................................................................................9 Overview............................................................................................................. 9 Connection with Dante Enabled Devices........................................................... 9 Setup ...................................................................................................10 Overall Process ................................................................................................ 10 Connection between the Device and a Computer ........................................... 10 Setting up the Power Supply ............................................................................ 11 Configuring the Audio Routing of the Dante Network ...................................... 11 Installing TOOLS for NUAGE............................................................................ 11 Configuring the Workgroup on NUAGE ........................................................... 11 Description of the Device ..................................................................12 Front Panel ....................................................................................................... 12 Rear Panel ........................................................................................................ 14 Description of the Software Programs.............................................17 NUAGE I/O Setup............................................................................................. 17 NUAGE Workgroup Manager........................................................................... 19 Troubleshooting.................................................................................21 Appendix.............................................................................................21 Firmware Updates ............................................................................................ 21 Specifications ....................................................................at the end of the book Pin Assignment..................................................................at the end of the book Dimensions........................................................................at the end of the book Block Diagrams .................................................................at the end of the book GNU GENERAL PUBLIC LICENSE ...................................at the end of the book 4 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Use only the supplied power cord/plug. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Never insert or remove an electric plug with wet hands. Fire warning • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. If you notice any abnormality Do not open • This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - It emits unusual smells or smoke. - Some object has been dropped into the instrument. - There is a sudden loss of sound during use of the device. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • When setting up the device, make sure that the front-panel power switch can be easily turned ON/OFF. If some trouble or malfunctions occurs, immediately turn off the power switch and disconnect the plug from the outlet. • If the device is mounted in an EIA standard rack, carefully read the section “Precautions for Rack Mounting” on page 8. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), malfunction, or even fire. Location • Do not place the device in an unstable position where it might accidentally fall over. • Do not block the vents. This device has ventilation holes at the sides to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. Connections • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. Maintenance • Remove the power plug from the AC outlet when cleaning the device. • Before moving the device, remove all connected cables. PA_en_1 1/2 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 5 NOTICE Handling caution • Do not insert your fingers or hands in any gaps or openings on the device (vents, etc.). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, etc.) If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling and Maintenance • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise. • Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. European Models • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. Inrush Current based on EN 55103-1:2009 2.0 A (on initial switch-on) 2.0 A (after a supply interruption of 5s) Conforms to Environments: E1, E2, E3 and E4 • When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature — when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the top of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. • Always turn the power off when the device is not in use. Serial No. Information About copyrights Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. About this manual • The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. • Windows is a registered trademark of Microsoft® Corporation in the United States and other countries. • Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. • To view PDF files, you will need to install Adobe Reader on your computer. You can download the latest Adobe Reader at the following website. http://www.adobe.com About this product The input/output level (Max. before clip) specification can be customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will be charged for this procedure.) For details, contact your Yamaha dealer. PA_en_1 6 2/2 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Introduction Introduction Thanks to experience with the DM and O series, intensive research, and invaluable feedback from our users, it is our great pleasure to be able to deliver a new level of production support in the NUAGE series. Our technology is there to give you unrestricted creative freedom, and we sincerely hope that the NUAGE series plays a role in your growth and continued success. A Message from the Development Team Thank you for choosing a NUAGE series NUAGE I/O unit. The NUAGE series is a professional music and sound production system based around Steinberg Nuendo digital audio workstation software. Over the 20 years that have elapsed since Yamaha began offering DM and O series digital consoles and other equipment for post production and music production, work schedules have become notably tighter with less time available for individual projects. The NUAGE series was created to respond to the deadline crunch with an optimized working environment that provides unprecedented efficiency as well as final quality. The Yamaha NUAGE series development team. Included Accessories • Power cable • Ferrite core • Rubber stoppers (4) • Operation Manual (this book) The core of the system is Steinberg Nuendo, a DAW that is acclaimed for its outstanding workflow efficiency and sonic quality. The NUAGE MASTER (Ncs500-CT control surface) and NUAGE FADER (Ncs500-FD control surface) units were specifically developed to support and enhance Nuendo operability. NUAGE MASTER provides a comprehensive concentration of post production controls in an efficient, easy-access layout. NUAGE FADER integrates seamlessly with the Nuendo mixer window, providing an intuitive hands-on extension to the software. NOTE And then there’s the sound. NUAGE I/O audio interface units have been designed to deliver the superior Nuendo sound without compromise. Three models are currently available: the Nio500-D16 with 16 channels of AES/EBU input and output, the Nio500-A16 with 16 channels of analog input and output, and the Nio500-A8D8 with a combination of 8 channels of analog and 8 channels of AES/EBU input and output. The NUAGE I/O units connect to computers running Nuendo via the highly expandable Dante digital audio protocol, allowing multiple NUAGE I/O units to be flexibly incorporated in a wide variety of system configurations. Monitoring latency is near zero for comfortable, stress-free monitoring while recording, even when multiple I/O units are used with cascaded monitor buses. The development team was adamant that nearzero latency would be essential to allow musicians and artists to deliver their full creative and performance potential. • Gigabit Ethernet Switch Stability and dependability are essential in any professional working environment. In addition to minimizing latency, the DANTE ACCELERATOR (AIC128D audio interface card) used in conjunction with the NUAGE I/O units offers stable, reliable communication between I/O units and computer while allowing fast recovery from any problems that do arise. You can concentrate on the job at hand, secure in the knowledge that you’ll be able to deliver great results on time. • Attach the ferrite core to prevent electromagnetic interference when using the [CASCADE] connector. Fasten it to the Ethernet cable near the [CASCADE OUT] connector. • When using the unit on a slippery surface, attach the rubber stoppers to the specified location on the bottom panel of this device to prevent sliding. Items to Have Ready A network switch that features various functions for controlling and monitoring the network (such as QoS, the ability to assign priority to data flows — e.g., clock synchronization or audio transmission on certain data circuits — and IGMP Snooping, the ability to filter unnecessary multi-cast traffic) is recommended. • Ethernet cable A straight type (STP) of CAT5e or better is recommended. • TOOLS for NUAGE TOOLS for NUAGE is a software program which is necessary when connecting the device to a computer. When you install TOOLS for NUAGE, NUAGE Workgroup Manager, NUAGE Extension, and NUAGE PT Bridge (Mac only) will be installed. NUAGE Workgroup Manager is an application that allows control over the devices and DAW software applications as a Workgroup on NUAGE system. NUAGE Extension is a program that allows you to link the device with Nuendo (for versions which support the link function). NUAGE PT Bridge is a program that allows you to control Pro Tools (Mac only) using NUAGE FADER and NUAGE MASTER (with the exception of certain functions). TOOLS for NUAGE is available on the following website. http://www.yamahaproaudio.com/downloads/ NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 7 Introduction Precautions for Rack Mounting How to Read the Manual This unit is rated for operation at ambient temperatures ranging from 0 to 40 degrees Celsius. When mounting the unit with other device(s) in an EIA standard equipment rack, internal temperatures can exceed the specified upper limit, resulting in impaired performance or failure. When rack mounting the unit, always observe the following requirements to avoid heat buildup: Conventions • When mounting the unit in a rack with devices such as power amplifiers that generate a significant amount of heat, leave more than 1U of space between NUAGE I/O and other equipment. Also either leave the open spaces uncovered or install appropriate ventilating panels to minimize the possibility of heat buildup. • To ensure sufficient airflow, leave the rear of the rack open and position it at least 10 centimeters from walls or other surfaces. If the rear of the rack can’t be left open, install a commercially available fan or similar ventilating option to secure sufficient airflow. If you’ve installed a fan kit, there may be cases in which closing the rear of the rack will produce a greater cooling effect. Refer to the rack and/or fan unit manual for details. Connection between the Device and a Computer The device can be connected to a computer in one of two ways: with or without the DANTE ACCELERATOR. Using the DANTE ACCELERATOR gives you the added advantages of lower latency, using more channels, and utilization of a redundant network. The descriptions in this manual assume you are using the DANTE ACCELERATOR. To connect the device and a computer with the DANTE ACCELERATOR, install the Dante Controller to the computer. Dante Controller is a software application that allows configuration and audio routing of the Dante network. When not using the DANTE ACCELERATOR, install the Dante Controller and DVS (Dante Virtual Soundcard). Dante Controller is a software application that allows configuration and audio routing of the Dante network. DVS is a software application that uses the computer as a Dante-enabled device. Dante Controller is available on the following website. http://www.yamahaproaudio.com/ • Brackets and quotation marks Brackets ([ ]) and quotation marks (“ ”) around names and phrases in this manual are used to indicate the following. Mark Indication target [] • Buttons, switches, indicators, terminals, etc. on the device. • Keys on a computer keyboard. “” • Menus, buttons, tabs, areas, windows, etc. on a computer window or software window. • Excerpts of messages, function names, terms in the manual, etc. • Windows or Mac When the procedures or explanations are specific to only one of the platforms, Windows or Mac, this is properly indicated in the manual. When the platforms do not appear, procedures or explanations are for both Windows and Mac. • Procedures “” appears on some procedures in the manual. For example, the string “Devices”  “Device Setup”  “Control Panel” indicates that you should perform the procedures in the following order. 1. Click the “Devices” menu. 2. Select the “Device Setup” option. 3. Click the “Control Panel” button. • Keyboard Shortcuts [Windows modifier key]/[Mac modifier key]+[key] shows the shortcut keys. For example, [Ctrl]/[command]+[Z] means “press [Ctrl] under Windows or [command] under Mac, then press [Z].” • Screens This manual predominantly uses screenshots of Windows. However, Mac screenshots are used when instructions of the function apply only to the Mac. Also, this manual uses screenshots of Nuendo 6. If you are using another version of Nuendo, the actual screenshots might not be the same. For details, refer to the Nuendo manuals (PDF) opened from the “Help” menu. DVS is commercially available on the following website. 8 http://www.audinate.com/ Nuendo References For details on Dante Controller and DVS, refer to the respective manuals. For brevity, the descriptions of Nuendo functions in this manual have been kept simple and basic. For details on Nuendo functions, refer to the Nuendo manuals (PDF) opened from the “Help” menu. NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual About Dante About Dante Redundant Network Overview This product features Dante technology as a protocol to transmit audio signals. Dante is a network protocol developed by Audinate. It is designed to deliver multichannel audio signals at various sampling and bit rates, as well as device control signals over a Giga-bit Ethernet (GbE) network. Dante also offers the following benefits: • It transmits up to 512 in/512 out, for a maximum total of 1024 audio channels over a GbE network. (The NUAGE I/O series can be accommodate up to eight devices, 128 in/128 out with a 24-bit resolution on a NUAGE system.) • Dante-enabled devices will automatically configure their network interfaces and find each other on the network. You can label Dante devices and their audio channels with names that make sense to you. • Dante uses high accuracy network synchronization standards to achieve sample-accurate playback with extremely low latency and jitter. • Dante supports redundant connections via primary and secondary circuits to defend against unforeseen difficulties. By taking advantages of these benefits, you can skip any complicated procedures to automate connections and setups of Dante-enabled devices, remotely control I/O racks or amplifiers from a mixing console, or make multitrack recordings to a DAW, such as Nuendo, installed on a computer in the network. Visit Audinate website for more details on Dante. http://www.audinate.com/ More information on Dante-enabled devices are also posted on the Yamaha Pro Audio website: http://www.yamahaproaudio.com/ Connection with Dante Enabled Devices To connect with Dante enabled devices, use a star connection or a daisy chain connection (enabled devices only). A redundant network consists of two circuits, a primary circuit and a secondary circuit. Normally, the network operates on the primary circuit. However, if the primary connection is broken, the secondary circuit will automatically take over communications. Therefore, using a redundant network with a star topology would increase communication stability relative to a daisy chain network. Computer Ethernet port Network switch Network switch Dante-enabled device PRIMARY SECONDARY Dante-enabled device PRIMARY SECONDARY Dante-enabled device SECONDARY PRIMARY Daisy Chain Connection (enabled devices only) A daisy chain is a wiring scheme in which multiple devices are connected together in sequence. This connection method is suitable for a simple system with a small number of devices. However, if a large number of devices are connected, the latency value must be increased. Also, if a connection is broken in a daisy chain network, the signal flow is interrupted at that point and no signal will be transferred beyond that point. Computer Ethernet port Star Connection In a star connection, each device is connected to a central network switch. Using a GbE-compatible network switch enables you to configure a wide-band, large-scale network. We recommend a network switch that features various functions to control and monitor the network (such as Qos, the ability to assign priority to data flows — e.g., clock synchronization or audio transmission on certain data circuits.) With this topology, it is common to configure a redundant network so that an unexpected network problem will not affect any audio or otherwise stable communications. Network switch PRIMARY Dante-enabled device SECONDARY PRIMARY Dante-enabled device SECONDARY PRIMARY Dante-enabled device NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 9 Setup Setup Connection between the Device and a Computer Overall Process Connect the devices and computer by using a star connection or a daisy chain connection. This section explains how to set up the device for use with the DANTE ACCELERATOR. Before setting up, make sure that the following conditions are met. Star Connection • The DANTE ACCELERATOR installed to the computer works properly. This section explains the connections when configuring a redundant network. • The Dante Controller has already been installed. 1. Connect the Ethernet cable as shown below. For details, refer to the DANTE ACCELERATOR manual. 1. Connect the device to a computer with a Ethernet cable.  “Connection between the Device and a Computer” (page 10) Computer Ethernet port 2. Connect the power cable then turn the DANTE ACCELERATOR power on.  “Setting up the Power Supply” (page 11) PRIMARY SECONDARY 3. Configure the audio routing of the Dante network with the Dante Controller.  “Configuring the Audio Routing of the Dante Network” (page 11) Network switch Network switch ID#1 4. Install TOOLS for NUAGE.  “Installing TOOLS for NUAGE” (page 11) PRIMARY 5. Configure the Workgroup on NUAGE with CASCADE OUT ID#2 the NUAGE Workgroup Manager.  “Configuring the Workgroup on NUAGE” (page 11) PRIMARY ID#3 SECONDARY CASCADE IN SECONDARY CASCADE OUT CASCADE IN PRIMARY SECONDARY 2. Set the [UNIT ID rotary switch] on the rear panel to a unique ID. 3. Turn on (down) the [Dip switch] No.1 on the rear panel. NOTE Redundant network operation may not be available on the DANTE ACCELERATOR depending on its firmware version. Make sure that the firmware version currently on the DANTE ACCELERATOR supports a redundant network by checking the following website. http://www.yamahaproaudio.com/ 10 NUAGE I/O (16D )/ NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Setup Daisy Chain Connection 1. Connect the Ethernet cable as shown below. Configuring the Audio Routing of the Dante Network 1. Launch Dante Controller. 2. In the “Routing” tab on the “Network View” window, set the audio routing by placing a check mark at the intersection of the desired devices. Computer DANTE ACCELERATOR To use the link function with Nuendo, set up as follows. Ethernet port PRIMARY • Set the sample rate and pull-up/pull-down parameters on NUAGE I/O and DANTE ACCELERATOR to the same settings. Network switch ID#1 CASCADE OUT ID#2 CASCADE IN CASCADE OUT ID#3 CASCADE IN • Join the inputs and outputs in the matrix. For example, set channels 1 through 16 on NUAGE I/ O to channels 1 through 16 on DANTE ACCELERATOR. PRIMARY SECONDARY PRIMARY SECONDARY PRIMARY 2. Set the [UNIT ID rotary switch] on the rear panel to a unique ID. NOTE 3. Turn off (up) the [Dip switch] No.1 on the For details on the Dante Controller, refer to the Dante Controller manual. rear panel. Setting up the Power Supply 1. Insert one plug of the power cable into the Installing TOOLS for NUAGE To install TOOLS for NUAGE, double-click the installer file you have downloaded from the website. For details, refer to the TOOLS for NUAGE installation guide. [AC IN] terminal on the device. 2. Insert the other plug of the power cable into a proper AC wall outlet. 3. Turn on (|) the power. WARNING Only use the included power cable (or an equivalent recommended by Yamaha). Using the wrong cable can result in damage to the device or overheating. CAUTION Remove the plug of the power cable from the outlet when the device is not be used for extended periods of time, or during electrical storms. Configuring the Workgroup on NUAGE To configure the Workgroup, open the NUAGE Workgroup Manager then register the devices and DAW software applications to the Workgroup. For details, refer to the NUAGE Workgroup Manager manual (PDF). To open the NUAGE Workgroup Manager manual, double-click the NUAGE Workgroup Manager icon on the task tray (Windows) or menu bar (Mac) for opening the window, then click the “Manual” icon. The setup is now completed. NUAGE I/O (16D )/ NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 11 Description of the Device Description of the Device Front Panel NUAGE I/O (16D) 1 2 1 2 1 2 4 3 5 6 3 5 6 3 5 6 NUAGE I/O (16A) NUAGE I/O (8A8D) 12 4 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Description of the Device 1 [INPUT level meter] 4 [SRC indicator] Indicates the input signal level of [ANALOG INPUT] (page 16) or [AES/EBU] (page 16) on the rear panel. Indicates the status of the SRC (sample rate converter), on (lit) or off (unlit). Lamp Lighting level Top (red) 0 dBFS Second (orange) -3 dBFS or more Third (orange) -14 dBFS or more Bottom (green) -48 dBFS or more When you turn SRC on, even if the sample rate at which the device is operating differs from the sample rate of the audio signal input to the device, the SRC function automatically converts the rate of the signal so that playback will be correct. SRC is available on every two adjacent channels. To turn SRC on/off, use the NUAGE Workgroup Manager (page 19). 2 [SAMPLE RATE indicator] 5 [OUTPUT level meter] Indicates the sample rate of the device. To select the sample rate of the device, use the NUAGE Workgroup Manager (page 19). Indicates the output signal level of [ANALOG OUTPUT] (page 16) or [AES/EBU] (page 16) on the rear panel. 3 [CLOCK indicator] Indicates the word clock source of the device. To select the word clock source of the device, use the NUAGE Workgroup Manager (page 19). Lamp Lighting level Top (red) 0 dBFS Second (orange) -3 dBFS or more Third (orange) -14 dBFS or more Bottom (green) -48 dBFS or more The [SYSTEM indicator] indicates the system status of the device on the Dante network. 6 [Power switch] Turns the power on (I) and off (P). The lamp lights when the power is on, and is unlit when the power is off. Lamp Status Left (green) Lit Description NOTICE The device is working properly. Rapidly turning the unit on and off in succession can cause it to malfunction. After turning the unit off, wait for at least 6 seconds before turning it on again. Left (green) Flashes (every The firmware updating is in second) progress. Right (red) Lit The memory on the device does not work properly. Right (red) Flashes (every The CPU on the device does not second) work properly. The [SYNC indicator] indicates the synchronization status of the device on the Dante network. Lamp Status Left (green) Lit Description The device is working as the slave on the Dante network. Left (green) Flashes (every The device is working as the master second) on the Dante network. Right (orange) Lit Synchronization with the Dante network is in progress. Right (orange) Flashes (every The device is not synchronized with second) the Dante network. NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 13 Description of the Device Rear Panel NUAGE I/O (16D) 1 14 2 7 8 5 6 3 4 2 NUAGE I/O (8A8D) 1 4 2 NUAGE I/O (16A) 1 3 3 4 ) ! 7 8 5 6 $ 9 ) ! 7 8 5 6 9 @ 9 @ ) ! NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual # # $ Description of the Device 1 [AC IN] 6 [SECONDARY] (RJ-45 connector) For connection to the power cable. The electric fan for expelling heat and cooling the unit. The same as [PRIMARY]. However, the connection configuration varies depending on the settings of [Dip switch] (page 15). For details on how to connect the devices, refer to “Setup” (page 10). 3 [UNIT ID rotary switch] 7 [SYSTEM LINK OUT] (BNC connector) Sets the device ID on the Dante network. When connecting multiple devices, set the ID on each device to a different number. Note that you can only select the device ID while the power is off. If you change this while the power is on, the new device ID will not be applied. For connection to the BNC coaxial cable. When connecting this connector to NUENDO SyncStation, Nuendo and the devices maintain accurate synchronization with each other. 2 [Fan] 8 [WORDCLOCK OUT] (BNC connector) 4 [Dip switch] Sets the device settings or initializes them. Note that you can only select [Dip switch] while the power is off. If you change this while the power is on, the settings will not be applied. For connection to the BNC coaxial cable. This connector outputs the word clock signal. 9 [WORDCLOCK IN] (BNC connector) For connection to the BNC coaxial cable. This connector receives the word clock signal. [Dip switch] Description 1 2 Selects whether [SECONDARY] (page 15) will operate as a redundant network (page 9) or daisy chain connection (page 9). [SECONDARY] will operate as a redundant network when you turn this on (down), and daisy chain connection when you turn this off (up). Initializes the device settings. Follow the steps below. 1. Turn the power of the device off. 2. Turn [Dip switch 2] on (down). 3. Turn the power of the device on, then wait for the [OUTPUT level meter] of the 16 channels to flash at intervals. 4. Turn the power of the device off. 5. Turn [Dip switch 2] off (up). 6. Turn the power of the device on. 3 Not used. Turn it off (up) at any time. 4 Not used. Turn it off (up) at any time. ) [CASCADE OUT] (RJ-45 connector) For connection to the Ethernet cable (CAT5e or better recommended). This connector inputs and outputs sixteen channels of audio for the direct monitoring. This is useful when outputting the audio signal to another device with near-zero latency. You can use this function with Nuendo. When connecting multiple devices, connect this to the [CASCADE IN] terminals on other devices as shown. ID#1 CASCADE OUT ID#2 5 [PRIMARY] (RJ-45 connector) CASCADE IN CASCADE OUT For connection to the Ethernet cable (CAT5e or better recommended). This connector is for construction of the Dante network, and is capable for input/output of sixteen channels of audio. For details on how to connect the devices, refer to “Setup” (page 10). ID#3 CASCADE IN Up to eight devices can be connected in this way. The lamp on this connector lights when the device is communicating with the Dante network. NOTE NOTE • To use direct monitoring, complete “Setup” (page 10) then turn on “Direct Monitoring” in the “Device Setup” menu on Nuendo. • Use STP (shielded twisted pair) cable to prevent electromagnetic interference. Make sure that the metal parts of the plugs are electrically connected to the STP cable shield by conductive tape or comparable means. • Connect only Dante-compatible devices or GbE-compatible devices (including a computer). • Use a straight type (STP) cable of less than 3 meters. • The device can input and output audio signals for direct monitoring when the sample rate setting on the device is 96 kHz or lower. Direct monitoring is not supported for settings of over 96 kHz. ! [CASCADE IN] (RJ-45 connector) Refer to [CASCADE OUT]. NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 15 Description of the Device @ [ANALOG OUTPUT] (D-sub 25-pin connector) For connection to a 25-pin D-sub analog cable. This connector outputs eight channels of audio. # [ANALOG INPUT] (D-sub 25-pin connector) For connection to a 25-pin D-sub analog cable. This connector inputs eight channels of audio. $ [AES/EBU] (D-sub 25-pin connector) For connection to a 25-pin D-sub digital cable. This connector inputs and outputs eight channels of audio. 16 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Description of the Software Programs Description of the Software Programs Controls and Functions Bass Management Window NUAGE I/O Setup 1 2 3 6 7 4 5 8 1 On/Off Turns Bass Management on and off. Overview 2 Presets This software is for configuring the settings of the device from Nuendo. To open this window, click the Nuendo menu “Device”  “NUAGE I/O Setup.” The following presets are available in the default settings. NUAGE I/O Setup has the following two windows. • Bass Management window • ATT & Delay window In the Bass Management window, you can separately adjust the bass sound of the output signal from the device in surround sound applications. In the ATT & Delay window, you can adjust the level and delay of the output signal from the device. To select the windows, click the tabs on the upper side of the NUAGE I/O Setup window. For selecting, storing, and deleting the preset. Preset HPF LPF1 1/2/3/4 LPF2 ATT 1/2 AMP DVD LFE80Hz 80-12 80-24 80-24 0 +10 DVD LFE120Hz 80-12 120-42 80-24 0 +10 Movie LFE80Hz 80-12 80-24 80-24 -3 +10 Movie LFE120Hz 80-12 120-42 80-24 -3 +10 Bypass THRU THRU 0 0 MUTE 3 HPF1/2/3/4 When you press the NUAGE Workgroup Manager button on the upper right of the window, you can open the device settings window opened from the NUAGE Workgroup Manager. However, this is only available when launching the NUAGE Workgroup Manager on the same computer. Selects the type of high pass filter for each channel. NOTE Option Description THRU The filter is not applied. 80-12 A Butterworth filter with a cutoff frequency of 80 Hz and -12 dB of attenuation. 80-12L A Linkwitz filter with a cutoff frequency of 80 Hz and -12 dB of attenuation. 80-24 A Butterworth filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. 80-24L A Linkwitz filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. • To use these functions, complete “Setup” (page 10). • To use the Bass Management function, create a surround output bus (such as 5.1 channels) in the Nuendo menu “Devices”  “VST connection.” Also, assign the ports in one NUAGE I/O to the ports of this output bus. NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 17 Description of the Software Programs ATT & Delay Window 4 LPF1 Selects the type of low pass filter for the LFE channel. Option Description THRU The filter is not applied. 80-24 A Butterworth filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. 80-24L A Linkwitz filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. 120-42 A Butterworth filter with a cutoff frequency of 120 Hz and -42 dB of attenuation. 1 2 5 LPF2 Selects the type of low pass filter for the LFE channel which is sent the signal from each channel. Option Description THRU The filter is not applied. 80-24 A Butterworth filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. 80-24L A Linkwitz filter with a cutoff frequency of 80 Hz and -24 dB of attenuation. MUTE The filter is muted. 6 ATT1/2 Sets the attenuator for each channel. The setting range is from 0 dB to -12 dB. 7 AMP Sets the amplifier for the LFE channel. The setting range is from 0 dB to +12 dB. 8 Block diagram Indicates the position of each parameter in Bass Management. 3 4 5 6 7 1 Presets For selecting, storing, and deleting the preset. 2 Monitor Selects the monitor for configuring the settings. 3 Mute on/off Turns muting of the channel on and off. 4 Channel Displays the channel. 5 Port Displays the channel port. 6 ATT(dB) Sets the attenuator/gain for speaker 1 and 2. The setting range is from 0 dB to -12 dB, and the smallest unit is 0.1 dB. 7 DELAY(ms) Sets the delay for the channel. The setting range is from 0 to 30 milliseconds, and the smallest unit is 0.02 milliseconds. 18 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Description of the Software Programs NUAGE Workgroup Manager To configure these settings, use the “Property Window” opened by clicking “Property” on the Workgroup area in the Main window. Overview This is a software application that allows control over the devices and DAW software applications as a Workgroup on NUAGE system. To open this window, double-click the NUAGE Workgroup Manager icon on the task tray (Windows) or menu bar (Mac). This section provides only the descriptions regarding the device settings on the NUAGE Workgroup Manager. For details on the NUAGE Workgroup Manager, refer to the corresponding manual (PDF) which can be opened from the “Manual” icon. You can configure the following device settings in the NUAGE Workgroup Manager. However, the setting menu will differ depending on the particular devices being used. • Adjusting the trim of the analog input and output signals. Controls and Functions NUAGE I/O (16D) 1 2 4 3 5 6 7 8 • Selecting the level of the analog input signal. • Selecting the word clock source. • Turning the SRC (sample rate converter) of the digital input signal on and off. • Turning the dual wire on and off. NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 19 Description of the Software Programs NUAGE I/O (16A) 1 2 4 3 Update Update the device’s firmware. For details, refer to the NUAGE Firmware Update Guide. 3 4 MAC Address Displays the MAC Address. 5 6 5 Word Clock Source Selects the word clock source. 9 ) 6 Input and output Displays the input and output. 7 Dual Wire Turns the Dual Wire function on and off. You can turn on and off the Dual Wire by eight channels. This function is available when the sample rate is set to 88.2, 96, 176.4, and 192 kHz, and also the SRC is turned off. 8 SRC Turns the sample rate converter on and off. This function is only available when the Dual Wire is turned off. NUAGE I/O (8A/8D) 9 Level Selects the input level. 1 2 4 3 ) Trim Adjusts the trim. 5 6 9 ) 7 8 1 Name Displays the name of the device or DAW software. To change this name, click “Property” on the Workgroup area in the Main window. 2 Version Displays the version. You can confirm the firmware version in case of devices, or the version of NUAGE Extension in the case of Nuendo, or the version of NUAGE PT Bridge in the case of Pro Tools. 20 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Troubleshooting Troubleshooting Appendix Firmware Updates Power does not turn on. • Is [Power switch] turned on? • Is the power cable connected to a proper AC outlet? • Is the power cable plug inserted all the way? If the power still does not turn on, contact your Yamaha dealer. Device is not communicating with Nuendo • Is the Ethernet cable connected properly? • Has “Installing TOOLS for NUAGE” (page 11) already been completed? • Has “Configuring the Workgroup on NUAGE” (page 11) already been completed? • Has “Configuring the Audio Routing of the Dante Network” (page 11) already been completed? This product enables you to update the unit firmware to improve operations, add functions, and correct possible malfunctions. The following two types of firmware are available for the unit. • Unit’s firmware • Dante module firmware You must update each type of firmware separately. Details on updating the firmware are available on the following website: http://www.yamahaproaudio.com/ For information on updating and setting up the unit, please refer to the firmware update guide available on the website. NOTE When you update Dante firmware on the unit, be sure to update Dante firmware on other Dante-compatible devices connected to the NUAGE I/O. • In case of connecting multiple devices, has the [UNIT ID rotary switch] been set to a unique ID? • Have the fire wall settings been set property? NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 21 Specifications ELECTRICAL CHARACTERISTICS Internal Sampling Frequency Analog Input/ Output 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz 44.1kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm 48kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm 88.2kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm 96kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm 176.4kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm 192kHz +4.1667%/+0.1%/-0.1%/-4.0% ±200ppm External Frequency Response ±0.5dB, 20Hz – 20kHz, ref to the nominal output level @1kHz, Input&Output Gain: 0dB, Input level +4dBu(typ) THD+N*1 Less than 0.005%, input to output, GAIN: 0dB Dynamic Range 120dB typ., ADC 120dB typ., DAC Crosstalk@1kHz -100dB, CH1 – 16 , adjacent inputs ANALOG INPUT CHARACTERISTICS Input level Input Terminals ANALOG INPUT Actual Load Impedance For Use With Nominal GAIN 20kΩ (BAL) 150Ω Lines 10kΩ (UNBAL) 600Ω Lines Nominal Max. before clip 0dB +4dBu (1.23 V) +24dBu (12.28V) +12dB -10dBV (0.32 V) +10dBV (3.16 V) 0dB +4dBu (1.23 V) +24dBu (12.28V) +12dB -10dBV (0.32 V) +10dBV (3.16 V) Connector in Console D-SUB Connector 25P (Female) D-SUB Connector 25P (Female) The input level (Max. before clip) specification can be customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will be charged for this procedure.) For details, contact your Yamaha dealers. ANALOG OUTPUT CHARACTERISTICS Output level Output Terminals ANALOG OUTPUT Actual Source Impedance For Use With Nominal GAIN 75Ω (BAL) 10kΩ Lines 0dB Nominal Max. before clip +4dBu (1.23 V) +24dBu (12.28V) Connector in Console D-SUB Connector 25P (Female) The output level (Max. before clip) specification can be customized to +22dBu, +20dBu,+18dBu, +15dBu. (A fee will be charged for this procedure.) For details, contact your Yamaha dealer. DIGITAL INPUT CHARACTERISTICS Terminal Format Data length Level Connector in Console AES/EBU AES/EBU 24bit RS422 D-SUB Connector 25P (Female) DIGITAL OUTPUT CHARACTERISTICS Terminal Format Data length Level Connector in Console AES/EBU AES/EBU Professional use 24bit RS422 D-SUB Connector 25P (Female) DIGITAL INPUT & OUTPUT CHARACTERISTICS Terminal Format Data length Level Connector in Console Primary/Secondary Dante 24bit 1000Base-T RJ-45 x 2 Cascade - 32bit LVDS*2 RJ-45 x 2 CONTROL I/O CHARACTERISTICS Terminal WORD CLOCK Format Level Connector in Console IN - TTL/75Ω terminated BNC Connector OUT - TTL/75Ω BNC Connector - 1.0±0.2Vp-p/75Ω*3 BNC Connector System Link Out General Specifications Power Requirements (wattage) Nio500-D16: 51W Nio500-A16: 51W Nio500-A8D8: 51W Power Requirements (voltage and hertz) US/Canada: 120V 60Hz Japan: 100V 50/60Hz China: 110 – 240V 50/60Hz Korea: 220V 60Hz Other: 110 – 240V 50/60Hz Temperature Range Operating temperature range: 0 – 40°C Storage temperature range: -20 – 60°C Dimensions (W x H x D) 480 x 88 x 369 mm Net Weight Nio500-D16: 6.4kg Nio500-A16: 6.7kg Nio500-A8D8: 6.7kg Included Accessories Power cable, Ferrite core, Ruber stoppers (4), Operation Manual *1 These characteristics are measured with A-weighting filter and/or 30kHz LPF. *2 Hi Speed CML *3 AES-3id Pin Assignment 13 1 25 14 Analog Input Signal Input Ch 1 (9) 2 (10) 3 (11) 4 (12) 5 (13) 6 (14) 7 (15) 8 (16) Hot 24 10 21 7 18 4 15 1 Cold 12 23 9 20 6 17 3 14 Pin Open GND 13 2, 5, 8, 11, 16, 19, 22, 25 Open GND 13 2, 5, 8, 11, 16, 19, 22, 25 Open GND 9, 11 10, 12, 13, 22, 23, 24, 25 Analog Output Signal Output Ch 1 (9) 2 (10) 3 (11) 4 (12) 5 (13) 6 (14) 7 (15) 8 (16) Hot 24 10 21 7 18 4 15 1 Cold 12 23 9 20 6 17 3 14 Pin Digital Input & Output Signal Pin Data In Ch Data Out Ch 1-2 (9-10) 3-4 (11-12) 5-6 (13-14) 7-8 (15-16) 1-2 (9-10) 3-4 (11-12) 5-6 (13-14) 7-8 (15-16) Hot 1 2 3 4 5 6 7 8 Cold 14 15 16 17 18 19 20 21 Specifications and descriptions in this manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Die technischen Daten und Beschreibungen in diesem Handbuch dienen nur der Information. Yamaha Corp. behält sich das Recht vor, Produkte oder technische Daten jederzeit ohne vorherige Ankündigung zu ändern oder zu modifizieren. Da die technischen Daten, das Gerät selbst oder das Zubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifelsfall bitte mit Ihrem Yamaha-Händler in Verbindung. Les caractéristiques techniques et les descriptions figurant dans le présent manuel sont fournies à titre d'information uniquement. Yamaha Corp. se réserve le droit de changer ou modifier les produits et leurs caractéristiques techniques à tout moment sans aucun préavis. Les caractéristiques techniques, le matériel ou les options peuvent varier selon le lieu de distribution. Veuillez par conséquent vous renseigner auprès de votre revendeur Yamaha. Las especificaciones y descripciones incluidas en este manual tienen una finalidad meramente informativa. Yamaha Corp. se reserva el derecho de cambiar o modificar los productos o especificaciones en cualquier momento y sin previo aviso. Puesto que las especificaciones, los equipos o las opciones podrían no ser las mismas en todos los casos, le rogamos consulte a su distribuidor de Yamaha. Le specifiche e le descrizioni riportate in questo manuale sono fornite a scopo puramente informativo. Yamaha Corp. si riserva il diritto di modificare prodotti o specifiche in qualsiasi momento senza preavviso. Poiché le specifiche tecniche, le apparecchiature e i componenti opzionali potrebbero variare a seconda del Paese in cui viene distribuito il prodotto, controllare queste informazioni presso il proprio rivenditore Yamaha. Технические характеристики и описания приводятся в данном руководстве исключительно в справочных целях. Корпорация Yamaha Corp. оставляет за собой право изменять или модифицировать продукты и технические характеристики в любое время без предварительного уведомления. Так как технические характеристики, оборудование и компоненты могут различаться в разных странах, обратитесь за информацией к местному представителю корпорации Yamaha. 本说明书中的技术规格及介绍仅供参考。Yamaha公司保留随时更改或修订产品或技术规格的权利，若确有更改，恕不事先通知。技术规格、设备或选 购件在各个地区可能均会有所不同，因此如有问题，请和当地Yamaha经销商确认。 仕様および外観は改良のため予告なく変更することがあります。 Dimensions NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) 11 358 369 430 88 480 [DANTE] (INPUT 1-16) (INPUT 1-16 FROM NEXT NUAGE I/O) [CASCADE OUT] (INPUT 1-16 FROM PREV. NUAGE I/O) [CASCADE IN] INPUT 1-16 16 16 16 METER 1 2 3 4 16 MATRIX BUS Same as the above Same as the above Same as the above Same as the above NUAGE I/O — 44.1/48/88.2/96kHz DELAY DELAY DELAY DELAY DELAY DELAY DELAY DELAY DELAY DELAY 8 OUTPUT 9-16 LEVEL 8 [ANALOG 1-8] [ANALOG 9-16] TRIM INPUT 9-16 INPUT 1-8 TRIM TRIM +4dBu/-10dBV 8 CASCADE MASTER/SLAVE 8 OUTPUT 1-8 [ANALOG 9-16] [ANALOG 1-8] NUAGE I/O (16A) OUTPUT 9-16 OUTPUT 1-8 [AES/EBU 9-16] [AES/EBU 1-8] 8 8 8 8 SURROUND MONITOR [AES/EBU 9-16] [AES/EBU 1-8] INPUT 9-16 INPUT 1-8 NUAGE I/O (16D) SELECTOR Block Diagrams OUTPUT PATCH [DANTE] (OUTPUT 1-16) METER 16 16 OUTPUT 9-16 OUTPUT 1-8 8 [AES/EBU 9-16] [ANALOG 1-8] 8 OUTPUT 1-16 (OUTPUT 1-16 TO PREV. NUAGE I/O) [CASCADE IN] (OUTPUT 1-16 TO NEXT NUAGE I/O) [CASCADE OUT] [AES/EBU 9-16] [ANALOG 1-8] TRIM 8 INPUT 9-16 INPUT 1-8 8 TRIM +4dBu/-10dBV LEVEL NUAGE I/O (8A8D) 16 [DANTE] (INPUT 1-16) INPUT 1-16 16 METER NUAGE I/O — 176.4/192kHz 8 8 OUTPUT 1-8 OUTPUT 9-16 8 [ANALOG 9-16] [ANALOG 1-8] [ANALOG 9-16] TRIM TRIM INPUT 9-16 OUTPUT 9-16 OUTPUT 1-8 [AES/EBU 9-16] [AES/EBU 1-8] 8 8 8 8 [AES/EBU 9-16] [AES/EBU 1-8] INPUT 9-16 INPUT 1-8 METER OUTPUT 9-16 OUTPUT 1-8 8 [AES/EBU 9-16] [ANALOG 1-8] 8 8 TRIM 8 INPUT 9-16 INPUT 1-8 OUTPUT 1-16 [AES/EBU 9-16] [ANALOG 1-8] TRIM LEVEL TRIM +4dBu/-10dBV 8 [ANALOG 1-8] INPUT 1-8 NUAGE I/O (8A8D) LEVEL NUAGE I/O (16D) [DANTE] (OUTPUT 1-16) +4dBu/-10dBV NUAGE I/O (16A) 16 GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: • a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. • b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. • c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: • a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, • b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machinereadable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, • c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. one line to give the program's name and an idea of what it does. Copyright © yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright © year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program. • Bedenken Sie, dass die Wiederverwendung von Quellcode, der von Yamaha an die Public Domain übergeben wurde, keiner Garantie unterliegt und dass Yamaha keine Verantwortung für den Quellcode übernimmt. • Der Quellcode kann von der folgenden Adresse heruntergeladen werden: http://yamahaproaudio.com/ Note concernant la distribution du code source Au cours des trois années qui suivent la sortie définitive d'usine, vous pouvez demander à Yamaha le code source de toute partie du produit fournie sous licence dans le cadre d'une licence GNU General Public License en envoyant un courrier à l'adresse suivante : You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker. Le code source vous sera fourni gratuitement. Nous pouvons toutefois vous demander de rembourser à Yamaha les frais d'expédition du code. signature of Ty Coon, 1 April 1989 • Notez que nous déclinons toute responsabilité pour les dommages résultant de modifications (ajouts/suppressions) apportées au logiciel de ce produit par un tiers autre que Yamaha (ou une partie autorisée par Yamaha). Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License. Note on source code distribution For three years after the final factory shipment, you may request from Yamaha the source code for any portions of the product which are licensed under the GNU General Public License by writing to the following address: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN The source code will be provided at no charge; however, we may require you to reimburse Yamaha for the cost of delivering the source code to you. • Note that we shall bear no responsibility whatsoever for any damage arising from changes (additions/ deletions) made to the software for this product by a third party other than Yamaha (or party authorized by Yamaha). • Note that re-use of source code released to the public domain by Yamaha is unguaranteed, and Yamaha shall not bear any responsibility whatsoever for the source code. • Notez que la réutilisation du code source distribué dans le domaine public par Yamaha n'est pas garantie et que Yamaha décline toute responsabilité pour le code source. • Vous pouvez également télécharger le code source à l'adresse suivante : http://yamahaproaudio.com/ Nota sobre la distribución del código fuente Durante tres años tras la salida final de fábrica, puede solicitar a Yamaha el código fuente de cualquier parte del producto para el que se conceda licencia según la Licencia Pública General (GNU), enviando solicitud escrita a: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN El código fuente se proporcionará sin cargo alguno; sin embargo, Yamaha podría solicitar el reembolso del coste de envío. • Debe tenerse en cuenta que no admitiremos responsabilidad alguna por cualesquiera daños que puedan derivarse de los cambios (adiciones o eliminaciones) realizados en el software de este producto por un tercero que no sea Yamaha (o alguien autorizado por Yamaha). • The source code can be downloaded from the following address: http://yamahaproaudio.com/ • Asimismo, debe tenerse en cuenta que la reutilización del código fuente que Yamaha hace de dominio público no tiene garantía alguna, y Yamaha no asumirá responsabilidad respecto a este código. Hinweis für den Zugriff auf Quellcode • El código fuente se puede descargar de la siguiente dirección: http://yamahaproaudio.com/ In einem Zeitraum von bis zu drei Jahren nach endgültiger Auslieferung können Sie von Yamaha den Quellcode für alle Teile des Produkts anfordern, die der allgemein-öffentlichen Lizenz (General Public License) GNU unterliegen, indem Sie ein Schreiben an folgende Adresse richten: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN Der Quellcode wird kostenlos zur Verfügung gestellt; es kann jedoch sein, dass wir Sie bitten, Yamaha für die durch die Lieferung entstandenen Kosten zu entschädigen. • Bedenken Sie bitte, dass wir keine Verantwortung für Schäden übernehmen, die aus Änderungen (Hinzufügung/Löschung) an der Software für dieses Produkt entstehen, die von Dritten außer Yamaha selbst (oder von Yamaha hierfür autorisierten Parteien) vorgenommen wurden. Note sulla distribuzione del codice sorgente Entro tre anni dalla consegna di fabbrica finale, è possibile richiedere a Yamaha il codice sorgente di qualsiasi parte del prodotto fornita con licenza GNU General Public License scrivendo al seguente indirizzo: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN Il codice sorgente verrà fornito senza spese, tuttavia Yamaha richiederà un rimborso per i relativo costi di spedizione. • Yamaha non si assume alcuna responsabilità per eventuali danni derivanti da modifiche (aggiunte/eliminazioni) effettuate al software di questo prodotto da terze parti diverse da Yamaha (o da terze parti autorizzate da Yamaha). • Il riutilizzo del codice sorgente rilasciato come dominio pubblico da parte di Yamaha non è garantito e Yamaha non si assume alcuna responsabilità relativa al codice sorgente. • È possibile scaricare il codice sorgente dal seguente indirizzo: http://yamahaproaudio.com/ Замечание о распространении исходного кода В течение трех лет после отгрузки с завода можно запросить в компании Yamaha исходный код для любой категории программных продуктов, на которые распространяется Универсальная общественная лицензия GNU, обратившись по следующему адресу: PA Marketing Group Marketing Department Pro Audio Division, YAMAHA Corporation 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN Исходный код поставляется бесплатно, однако вас могут попросить возместить корпорации Yamaha расходы по его пересылке. • Следует отметить, что корпорация не несет ответственности за любой ущерб, возникший в результате изменений (дополнений/ удалений), произведенных в программном обеспечении для данного продукта третьими лицами, не имеющими отношения к корпорации Yamaha (или не являющимися уполномоченными представителями корпорации Yamaha). • Также следует отметить, что вторичное использование исходного кода, выпущенного для публичного использования корпорацией Yamaha, не является предметом гарантии и что Yamaha не несет ответственности за любое использование такого исходного кода. • Исходный код можно загрузить с веб-сайта по адресу: http://yamahaproaudio.com/ 关于源代码分发的注意事项 在产品最终出厂后的3年内，您可以通过写信到以下地址向Yamaha索 取经GNU General Public License授权的本产品任何部分的源代码。 PA Marketing Group Marketing Department Pro Audio Division, YAMAHA 公司 10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, JAPAN 虽然源代码是免费提供的，但是我们可能会向您收取源代码的运送费 用。 • 请注意，我们对于由Yamaha （或Yamaha授权单位）以外的第三方 对本产品的软件所进行的变动 （添加/删除）而造成的任何损失概不 承担责任。 • 请注意，Yamaha不保证公开发布的源代码能再次使用，Yamaha对 源代码概不承担责任。 • 源代码可从下列地址下载： http://yamahaproaudio.com/ ソースコード配布について 本製品の最終出荷日から3年間は、製品のソースコードのうちGNU General Public Licenseに基づいてライセンス供与された部分につ いては、ソースコードを配布させていただきます。以下の住所にお 問い合わせください。 〒430-8650 浜松市中区中沢町10-1 ヤマハ(株) PA事業部マーケティング部 PAマーケティングG ソースコードの配布自体は無償ですが、ソースコードの送料につき ましてはご負担いただきます。 • 弊社(または弊社認定の関係者)以外の第三者による、この製品のソ フトウェアに対する変更や追加、削除などによって発生したいか なる損害に対しても、弊社は一切責任を負いません。 • 弊社により一般に公開されたソースコードの再利用は保証されて おりません。ソースコードに関して弊社は一切責任を負いません。 • また、ソースコードは以下のURLでも配布しております。 http://www.yamahaproaudio.com/japan/ja/ 有毒有害物质或元素 部件名称 铅（Pb） 汞（Hg） 镉（Cd） 六价铬（Cr (VI)） 多溴联苯 （PBB） 多溴二苯醚 （PBDE） 外壳、框架 × ○ ○ ○ ○ ○ 印刷线路板 × ○ ○ ○ ○ ○ ○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006标准规定的限量要 求以下。 × ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006标准规定的 限量要求。 （此产品符合EU的RoHS指令。） (この製品はEUのRoHS指令には適合しています。) (This product conforms to the RoHS regulations in the EU.) (Dieses Produkt entspricht der RoHS-Richtlinie der EU.) (Ce produit est conforme aux réglementations RoHS de l'UE.) (Este producto cumple con los requisitos de la directiva RoHS en la UE.) 此标识适用于在中华人民共和国销售的电子信息产品。 标识中间的数字为环保使用期限的年数。 Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. (weee_eu_en_01) Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden. In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC bringen Sie alte Geräte bitte zur fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen. Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten. Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel. [Information für geschäftliche Anwender in der Europäischen Unio] Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen. [Entsorgungsinformation für Länder außerhalb der Europäischen Union] Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode. (weee_eu_de_01) Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques. Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels. Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC. En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement inapproprié des déchets. Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits. [Pour les professionnels dans l'Union Européenne] Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour plus d'informations. [Information sur le traitement dans d'autres pays en dehors de l'Union Européenne] Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée. (weee_eu_fr_01) Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes. Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC. Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos. Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de gestión de residuos o el punto de venta en el cual usted adquirió los artículos. [Para usuarios de negocios en la Unión Europea] Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor información. [Información sobre la Disposición en otros países fuera de la Unión Europea] Este símbolo sólo es válido en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte por el método correcto de disposición. (weee_eu_es_01) Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura Questo simbolo sui prodotti, sull’imballaggio e/o sui documenti che li accompagnano significa che i prodotti elettrici ed elettronici non dovrebbero essere mischiati con i rifiuti domestici generici. Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con la Sua legislazione nazionale e le direttive 2002/96/CE. Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla salute umana e l'ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti. Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli. [Per utenti imprenditori dell'Unione europea] Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni. [Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea] Questo simbolo è valid0 solamente nell'Unione Europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il rivenditore e richieda la corretta modalità di smaltimento. (weee_eu_it_01) ADDRESS LIST NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col. San José Insurgentes, Delegación Benito Juárez, México, D.F., C.P. 03900 Tel: +52-55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda. Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila Olímpia – CEP 04551-010 – São Paulo/SP, Brazil Tel: +55-11-3704-1377 ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK, Buenos Aires, Argentina Tel: +54-11-4119-7000 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Edif. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, República de Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: +44-1908-366700 GERMANY Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH, Branch Switzerland in Thalwil Seestrasse 18a, 8800 Thalwil, Switzerland Tel: +41-44-3878080 NETHERLANDS/BELGIUM/ LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activités de Pariest, 77183 Croissy-Beaubourg, France Tel: +33-1-6461-4000 ITALY Yamaha Music Europe GmbH, Branch Italy Viale Italia 88, 20020, Lainate (Milano), Italy Tel: +39-02-93577-1 SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibérica, Sucursal en España Ctra. de la Coruna km. 17,200, 28231 Las Rozas de Madrid, Spain Tel: +34-91-639-88-88 GREECE Philippos Nakas S.A. The Music House 19th klm. Leof. Lavriou 190 02 Peania – Attiki, Greece Tel: +30-210-6686168 SWEDEN/FINLAND/ICELAND Yamaha Music Europe GmbH Germany filial Scandinavia JA Wettergrensgata 1, 400 43 Göteborg, Sweden Tel: +46-31-89-34-00 DENMARK Yamaha Music Denmark, Fillial of Yamaha Music Europe GmbH, Tyskland Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark Tel: +45-44-92-49-00 NORWAY Yamaha Music Europe GmbH Germany Norwegian Branch Grini Næringspark 1, 1332 Østerås, Norway Tel: +47-6716-7800 RUSSIA Yamaha Music (Russia) LLC. Room 37, entrance 7, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: +7-495-626-5005 OTHER EUROPEAN COUNTRIES Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 POLAND/LITHUANIA/LATVIA/ESTONIA Yamaha Music Europe GmbH Sp.z o.o. Oddzial w Polsce ul. Wrotkowa 14, 02-553 Warsaw, Poland Tel: +48-22-880-08-88 MALTA Olimpus Music Ltd. Valletta Road, Mosta MST9010, Malta Tel: +356-2133-2093 PA45 Yamaha Music India Private Limited P-401, JMD Megapolis, Sector-48, Sohna Road, Gurgaon-122018, Haryana, India Tel: +91-124-485-3300 INDONESIA PT. Yamaha Musik Indonesia (Distributor) Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: +62-21-520-2577 KOREA Yamaha Music Korea Ltd. 8F, Dongsung Bldg. 21, Teheran-ro 87-gil, Gangnam-gu, Seoul, 06169, Korea Tel: +82-2-3467-3300 MALAYSIA Yamaha Music (Malaysia) Sdn. Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: +60-3-78030900 SINGAPORE Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: +65-6740-9200 TAIWAN Yamaha Music & Electronics Taiwan Co.,Ltd. 2F., No.1, Yuandong Rd. Banqiao Dist. New Taipei City 22063, Taiwan, R.O.C. Tel: +886-2-7741-8888 THAILAND Siam Music Yamaha Co., Ltd. 3, 4, 15, 16th Fl., Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: +66-2215-2622 VIETNAM Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-8-3818-1122 OTHER ASIAN COUNTRIES AUSTRALIA TURKEY Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz Böl. No:3, Sariyer Istanbul, Turkey Tel: +90-212-999-8010 Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0 OTHER COUNTRIES INDIA OCEANIA MIDDLE EAST CYPRUS Yamaha Music & Electronics (China) Co.,Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: +86-400-051-7700 Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 AFRICA AUSTRIA/BULGARIA Yamaha Music Europe GmbH Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900 ASIA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, VIC 3006, Australia Tel: +61-3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation Sales & Marketing Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500 HEAD OFFICE Yamaha Corporation, Commercial Audio Business Division 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650 䲙偀જФ఼䷇ડ˄Ё೑˅ᡩ䌘᳝䰤݀ৌ Ϟ⍋Ꮦ䴭ᅝऎᮄ䯌䏃 1818 োѥ੠໻ॺ 2 ὐ ᅶ᠋᳡ࡵ⛁㒓˖4000517700 ݀ৌ㔥ഔ˖http://www.yamaha.com.cn ॖৡ : 䲙偀જ⬉ᄤ˄㢣Ꮂ˅᳝䰤݀ৌ ॖഔ : ∳㢣ⳕ㢣ᎲᏖ㢣Ꮂᮄऎ呓ቅ䏃 18 ো Yamaha Pro Audio global website: http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Group © 2012 Yamaha Corporation Published 07/2016 ᬍ⠜ MWHD-D0 Printed in China ZF63600
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Yamaha A8D Manual de usuario

Yamaha
Marca
Yamaha
Modelo
A8D
Tipo
Manual de usuario
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos