Samsung NE59M4320SB/AA-00 El manual del propietario

Categoría
Cocinas
Tipo
El manual del propietario

Este manual también es adecuado para

Electric Range
User manual
NE59M4320**
NE59M4320_DG68-00882A-01_EN.indd 1 2/16/2017 3:45:22 PM
2 English
Memo
Anti-tip device
WARNING
To reduce the risk of tipping the range, the range must be secured
by a properly installed Anti-Tip device. AFTER THE RANGE HAS
BEEN INSTALLED, CONFIRM THAT THE ANTI-TIP DEVICE HAS BEEN
PROPERLY INSTALLED AND VERIFY THAT THE ANTITIP DEVICE
IS PROPERLY ENGAGED. Refer to the installation manual for
instructions.
a) If the anti-tip device is not installed, a child or adult can tip the
range and be killed.
b) Verify that the anti-tip device has been properly installed and
engaged at the rear right (or rear left) of the range bottom.
c) If you move the range and then move it back into place, ensure
the antitip device is re-engaged at the right or left rear of the
range bottom.
d) Do not operate the range without the anti-tip device in place and
engaged.
e) Failure to do so can result in death or serious burns to children
or adults.
WARNING
Do not step, lean, or sit on the doors of the range. You can
cause the range to tip, resulting in burns or serious injuries.
Conrm that the Anti-Tip device is installed properly. Then, to
verify that the Anti-Tip device is engaged, grasp the top rear
edge of the range and carefully attempt to tilt it forward. The
Anti-Tip device should prevent the range from tilting forward
more than a few inches.
If you pull the range out from the wall for any reason, make
sure the antitip device is properly engaged when you push the
range back against the wall. If it is not, there is a risk of the
range tipping over and causing injury if you or a child stand,
sit, or lean on the open door.
Never completely remove the leveling legs. If you remove
the leveling legs, the range will not be secured to the anti-tip
device properly.
NE59M4320_DG68-00882A-01_EN.indd 2 2/16/2017 3:45:22 PM
English 3
Contents
Contents
Important safety instructions 4
Introducing your new range 16
Overview 16
What’s included with your range 16
Before you begin 17
Energy saving tips 17
Cooktop cooking 17
About cooktop cooking 17
How to set the appliance for cooktop cooking 19
Using the proper cookware 20
Choosing the proper cookware 21
Protecting the smoothtop 21
Operating the oven 22
The oven control panel 22
Setting the clock 23
Setting the kitchen timer 23
Timed cooking 24
Delay start 24
Turning the oven light on and off 25
Minimum and maximum settings 25
Using the oven racks 25
Baking 26
Convection baking 27
Convection roasting 28
Broiling 28
Using the easy cook feature 29
Using the keep warm feature 30
Using the sabbath feature 31
Extra features 32
Maintaining your appliance 34
Self-cleaning 34
Steam-cleaning 36
Care and cleaning of the oven 36
Care and cleaning of the glass cooktop 38
Removing and replacing the oven door 40
Removing and replacing the storage drawer 41
Changing the oven light 41
Troubleshooting 42
Troubleshooting 42
Information codes 46
Warranty (U.S.A) 47
Warranty (CANADA) 48
NE59M4320_DG68-00882A-01_EN.indd 3 2/16/2017 3:45:22 PM
4 English
Important safety instructions
Important safety instructions
Read and follow all instructions before using your oven to prevent
the risk of re, electric shock, personal injury, or damage when using
the range. This guide does not cover all possible conditions that may
occur. Always contact your service agent or manufacturer about
problems that you do not understand.
WHAT YOU NEED TO KNOW ABOUT
SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not
cover all possible conditions and situations that may occur. It is
your responsibility to use common sense, caution, and care when
installing, maintaining, and operating your oven.
Important safety symbols and precautions
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury
or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury
or property damage.
CAUTION
To reduce the risk of re, explosion, electric shock, or personal injury
when using your oven, follow these basic safety precautions.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicitly.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Note
These warning signs are here to prevent injury to you and others.
Please follow them explicitly.
After reading this section, keep it in a safe place for future reference.
STATE OF CALIFORNIA PROPOSITION
65 WARNING US ONLY
WARNING : This product contains chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
NE59M4320_DG68-00882A-01_EN.indd 4 2/16/2017 3:45:23 PM
English 5
Important safety instructions
FOR YOUR SAFETY
When using electrical appliances, you should follow basic safety
precautions, including the following:
CAUTION
Use this appliance only for its intended purpose as described in
this Owner’s Manual.
Potentially hot surfaces include the cooktop, areas facing the
cooktop, oven vent opening, surfaces near the opening, crevices
around the oven door.
Be sure your appliance is properly installed and grounded by a
qualied technician.
User servicing - Do not repair or replace any part of the
appliance unless specically recommended in this manual. All
other servicing should be referred to a qualied technician.
Always disconnect the power to the appliance before servicing
by removing the fuse or switching off the circuit breaker.
Do not enter the oven.
Do not store items of interest to children in cabinets above a
range or on the back guard of a range. Children climbing on
the range to reach items could be seriously injured.
Do not leave children alone. Never leave children alone or
unattended in an area where this appliance is in use. They
should never be allowed to sit or stand on any part of the
appliance.
Never use your appliance for warming or heating the room.
Do not use water on grease res. Turn off the oven to avoid
spreading the ames. Smother the re or ames by closing
the door or use a dry chemical, baking soda, or foam-type
extinguisher.
Avoid scratching or impacting glass doors, cooktops or control
panels. Doing so may lead to glass breakage. Do not cook on a
product with broken glass. Shock, re, or cuts may occur.
If there is a re in the oven during self clean, turn the oven
off and wait for the re to go out. Do not force the door
open. Introduction of fresh air at self-clean temperatures may
lead to a burst of ame from the oven. Failure to follow this
instruction may result in severe burns.
If the oven is heavily soiled with oil, self clean the oven before
using the oven again. Leaving the oil in place creates a risk of re.
Wipe up heavy soil on the oven bottom with a paper tower or
rag before self cleaning. Self cleaning the oven when there is
heavy soil on the oven bottom requires longer cleaning cycles
and produces more smoke.
NE59M4320_DG68-00882A-01_EN.indd 5 2/16/2017 3:45:23 PM
6 English
Important safety instructions
Important safety instructions
Storage in or on the appliance. Do not store ammable
materials in the oven or near the surface units. Be sure all
packing materials are removed from the appliance before
operating it. Keep plastics, clothes, and paper away from parts
of the appliance that may become hot.
Wear proper apparel. Never wear loose-tting or hanging
garments while using the appliance.
Use only dry potholders. Placing moist or damp potholders
on hot surfaces may result in burns from steam. Do not let the
potholder touch hot heating elements. Do not use a towel or
other bulky cloth.
Teach children not to play with the controls or any other part
of the range.
For your safety, do not use high-pressure water cleaners or
steam jet cleaners.
If the power cord is damaged, it must be replaced by the
manufacturer, its service agent, or similarly qualied persons
to avoid creating a hazard.
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
SURFACE COOKING UNITS
Never leave surface units unattended at high heat settings.
Boilovers cause smoking and greasy spillovers that may
ignite.
Protective Liners – Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested in the
manual. Improper installation of these liners may result in a
risk of electric shock or re.
To avoid oil spillover and re, use a minimum amount of oil
when shallow pan-frying and avoid cooking frozen foods with
excessive amounts of ice.
Do not lift the cooktop. Lifting the cooktop can damage the
range and cause the range to malfunction.
Do not operate the cooktop without cookware. If the cooktop
operates without cookware, the control knobs will become
hot.
Never use the glass cooktop surface as a cutting board.
NE59M4320_DG68-00882A-01_EN.indd 6 2/16/2017 3:45:23 PM
English 7
Important safety instructions
Use care when touching the cooktop. The glass surface of the
cooktop will retain heat after the controls have been turned
off.
Be careful when placing spoons or other stirring utensils on
the glass cooktop surface when it is in use. They may become
hot and could cause burns.
Use proper pan sizes. This appliance is equipped with surface
units of different size. Select pots and pans that have at
bottoms large enough to cover the surface area of the heating
element. Using undersized cookware will expose a portion of
the heating element to direct contact and may result in the
ignition of clothing. Matching the size of the pot or pan to the
burner will also improve efciency.
Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units – To reduce the risk of
burns, ignition of ammable materials, or spillage due to
unintentional contact with utensils, position utensil handles so
that they are turned inward and do not extend over adjacent
surface units.
Glazed cooking utensils. Only certain types of glass, glass/
ceramic, ceramic, earthenware, or other glazed cookware can
be used for rangetop service without breaking due to sudden
changes in temperature.
Cleaning. Read and follow all instructions and warnings on
the cleaning cream labels.
Be sure you know which control knob operates each surface
unit. Make sure you turned on the correct surface unit.
Always turn the surface units off before removing cookware.
When preparing aming foods under the hood, turn the fan
on.
Keep an eye on foods being fried at high or medium high
heat settings.
Do not store heavy items above the cooktop surface that
could fall and damage it.
Do not Use Decorative Surface Element Covers – If an element
is accidentally turned on, the decorative cover will become
hot and possibly melt. Burns will occur if the hot covers are
touched. Damage may also be done to the cooktop.
NE59M4320_DG68-00882A-01_EN.indd 7 2/16/2017 3:45:23 PM
8 English
Important safety instructions
Important safety instructions
ELECTRICAL SAFETY
Proper Installation - Be sure your appliance is properly
installed and grounded by a qualied technician.
The appliance should be serviced only by qualied service
personnel. Repairs carried out by unqualied individuals may
cause injury or a serious malfunction. If your appliance is in
need of repair, contact a Samsung authorized service center.
Failure to follow these instructions may result in damage and
void the warranty.
Flush - mounted appliances may be operated only after they
have been installed in cabinets and workplaces that conform
to the relevant standards. This ensures that the appliances are
installed in compliance with the appropriate safety standards.
If your appliance malfunctions or if fractures, cracks, or splits
appear:
- switch off all cooking zones
- unplug the range from the AC wall outlet
- contact your local Samsung service center.
WARNING
If the surface is cracked, switch off and unplug the appliance to avoid
the possibility of electrical shock. Do not use your cooktop until the
glass surface has been replaced.
WARNING
Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
The range should not be placed on a base.
CHILD SAFETY
WARNING
This appliance is not intended for use by young children or inrm
persons without the adequate supervision of a responsible adult.
Young children should be supervised to ensure that they do not
play with the appliance.
Keep children away from the door when opening or closing it as they
may bump themselves on the door or catch their ngers in the door.
The cooking zones will become hot when you cook. To keep small
children from being burned, always keep them away from the
appliance while you are cooking.
During self cleaning, the surfaces may get hotter than usual. Keep
small children away from the range when it is in the self-cleaning
mode.
WARNING
Accessible parts may become hot during use. To avoid burns, young
children should be kept away.
NE59M4320_DG68-00882A-01_EN.indd 8 2/16/2017 3:45:24 PM
English 9
Important safety instructions
OVEN
DO NOT TOUCH THE HEATING ELEMENTS OR INTERIOR
SURFACES OF THE OVEN. Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use, do
not touch or let clothing or other ammable materials contact
the heating elements or interior surfaces of the oven until
they have had sufcient time to cool. Other surfaces of the
appliance may become hot enough to cause burns. Among
these surfaces are oven vent openings and surfaces near these
openings, the oven door, and the window of the oven door.
Do not heat unopened food containers. The build-up of
pressure may cause the container to burst and result in injury.
Do not use the oven to dry newspapers. If overheated,
newspapers can catch on re.
Do not use the oven for a storage area. Items stored in an
oven can ignite.
Use care when opening the door. Let hot air or steam escape
before you remove food from or put food into the oven.
Protective liners. Do not use aluminum foil to line the oven
bottoms, except as suggested in the manual. Improper
installation of these liners may result in a risk of electric
shock or re.
Keep oven vent ducts unobstructed. The oven vent is located
above the right rear surface unit. This area could become hot
during oven use. Never block this vent or place plastic or
heat-sensitive items on it.
Placement of oven racks. Always place oven racks in the
desired location while the oven is cool. If the rack must be
moved while the oven is hot, use potholders. Do not let the
potholders come in contact with the hot heating element in
the oven.
Do not allow aluminum foil or a meat probe to contact the
heating elements.
During use, the appliance becomes hot. Care should be taken
to avoid touching heating elements inside the oven.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the oven door glass. They can scratch the surface which
may result in the glass shattering.
CAUTION
Do not attempt to operate the oven during a power failure. If the
power fails, always turn the oven off. If the oven is not turned off
and the power returns, the oven may begin to operate again. Food
left unattended could catch re or spoil.
NE59M4320_DG68-00882A-01_EN.indd 9 2/16/2017 3:45:24 PM
10 English
Important safety instructions
Important safety instructions
SELFCLEANING OVENS
Do not clean the door gasket. The door gasket is essential for a
good seal. Care should be taken not to rub, damage, or move the
gasket.
Never keep pet birds in the kitchen. Birds are extremely
sensitive to the fumes released during an oven self-clean
cycle. Fumes may be harmful or fatal to birds. Move birds to a
well-ventilated room.
Clean only the parts listed in this manual in the self-clean
cycle. Before self-cleaning the oven, remove the partition,
rack, utensils, and any food.
Before operating the self-clean cycle, wipe grease and food
soils from the oven. Excessive amounts of grease may ignite,
leading to smoke damage to your home.
Do not use any commercial oven cleaner or oven liner
protective coating of any kind in or on the outside of the oven.
Remove the nickel oven shelves from the oven before you
begin the self cleaning cycle or they may discolor.
If the self-clean mode malfunctions, turn the oven off and
disconnect the power supply. Have it serviced by a qualied
technician.
Excess spillage must be removed before you run the self
cleaning cycle.
VENTILATING HOOD
Clean ventilating hoods frequently. Do not let grease
accumulate on the hood or lter.
When aming foods under the hood, turn the fan on.
GLASS/CERAMIC COOKING SURFACES
DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS.
Surface units may be hot even though they are dark in color.
Areas near surface units may become hot enough to cause
burns. During and after use, do not touch, or let clothing or
other ammable materials contact the surface units or areas
near the units until they have had sufcient time to cool.
Among these areas are the cook-top and the facing of the
cook-top.
Do not cook on a broken cooktop. If the cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cook-top and create a risk of electric shock. Contact a
qualied technician immediately.
Clean the cooktop with caution. If a wet sponge or cloth is used
to wipe spills on a hot cooking area, be careful to avoid steam
burns. Some cleaners can produce noxious fumes if applied to a
hot surface.
NE59M4320_DG68-00882A-01_EN.indd 10 2/16/2017 3:45:24 PM
English 11
Important safety instructions
CRITICAL INSTALLATION WARNINGS
WARNING
This appliance must be installed by a qualied technician or
service company.
- Failing to have a qualied technician install the range may
result in electric shock, re, an explosion, problems with
the product, or injury.
Unpack the oven, remove all packaging material and examine
the oven for any damage such as dents on the interior or
exterior of the oven, broken door latches, cracks in the door,
or a door that is not lined up correctly. If there is any damage,
do not operate the oven and notify your dealer immediately.
Plug the power cord into a properly grounded outlet with
the proper conguration. Your oven should be the only item
connected to this circuit.
Keep all packaging materials out of the reach of children.
Children may use them for play and injure themselves.
Install your appliance on a level and hard oor that can
support its weight.
- Failing to do so may result in abnormal vibrations, noise, or
problems with the product.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe,
or telephone line.
- This may result in electric shock, re, an explosion, or
problems with the product
Do not cut or remove the ground prong from the power cord
under any circumstances.
Connect the oven to a circuit that provides the correct
amperage.
Do not install this appliance in a humid, oily or dusty location,
or in a location exposed to direct sunlight or water (rain
drops).
- This may result in electric shock or re.
Do not use a damaged power cord or loose wall socket.
- This may result in electric shock or re.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a
heavy object on the power cord, or insert the power cord
between objects.
- This may result in electric shock or re.
If the power cord is damaged, contact your nearest Samsung
service center.
NE59M4320_DG68-00882A-01_EN.indd 11 2/16/2017 3:45:24 PM
12 English
Important safety instructions
Important safety instructions
CRITICAL USAGE WARNING
CAUTION
If the appliance is ooded by any liquid, please contact your
nearest service center. Failing to do so may result in electric
shock or re.
If the appliance produces a strange noise, a burning smell, or
smoke, unplug the power plug immediately and contact your
nearest service center.
- Failing to do so may result in electric shock or re
In the event of a gas leak (such as propane gas, LP gas, etc.),
ventilate the area immediately. Do not touch the power cord.
Do not touch the appliance.
- A spark may result in an explosion or re.
Take care not to contact the oven door, heating elements, or
any of the other hot parts with your body while cooking or
just after cooking.
- Failing to do so may result in burns.
If materials inside the oven should ignite, keep the oven door
closed, turn the oven off and disconnect the power cord, or
shut off power at the fuse or circuit breaker panel. If the door
is opened, the re may spread.
Always observe safety precautions when using your oven.
Never try to repair the oven on your own - there is dangerous
voltage inside. If the oven needs to be repaired, contact an
authorized service center near you.
If you use the appliance when it is contaminated by foreign
substances such as food waste, it may result in a problem
with the appliance.
Take care when removing the wrapping from food taken out
of the appliance.
- If the food is hot, hot steam may be emitted abruptly when
you remove the wrapping and this may result in burns.
Do not attempt to repair, disassemble, or modify the
appliance yourself.
- Since a high voltage current enters the product chassis, it
may result in electric shock or re.
- When a repair is needed, contact your nearest service
center.
If any foreign substance such as water has entered the
appliance, contact your nearest service center.
- Failing to do so may result in electric shock or re.
Do not touch the power cord with wet hands.
- This may result in electric shock.
Do not turn the appliance off while an operation is in progress.
- This may cause a spark and result in electric shock or re.
NE59M4320_DG68-00882A-01_EN.indd 12 2/16/2017 3:45:24 PM
English 13
Important safety instructions
Keep all packaging materials well out of the reach of children,
as packaging materials can be dangerous to children.
- If a child places a plastic bag over its head, the child can
suffocate.
Do not let children or any person with reduced physical,
sensory, or mental capabilities use this appliance
unsupervised.
Make sure that the appliance’s controls and cooking areas are
out of the reach of children.
- Failing to do so may result in electric shock, burns, or injury.
Do not touch the inside of the appliance immediately after
cooking. The inside of the appliance will be hot.
- Failing to do so may result in burns.
Do not use or place ammable sprays or objects near the oven.
- Flammable items or sprays can cause res or an explosion.
Do not insert ngers, foreign substances, or metal objects
such as pins or needles into inlets, outlets, or holes. If foreign
substances are inserted into any of these holes, contact your
product provider or nearest service center.
Do not tamper with or make any adjustments or repairs to the
door. Under no circumstances should you remove the door or
outer shell of the oven.
Do not store or use the oven outdoors.
Never use this appliance for purposes other than cooking.
- Using the appliance for any purpose other than cooking
may result in re.
Open the cap or stopper of sealed containers (herb tonic tea
bottle, baby bottle, milk bottle and so on) before heating
them. Make a hole in food items that have shells (eggs,
chestnuts, etc) with a knife before cooking them.
- Failing to do so may result in burns or injury.
Never heat plastic or paper containers and do not use them
for cooking.
- Failing to do so may result in re.
Do not heat food wrapped in paper from magazines,
newspapers, etc..
- This may result in re.
Do not open the door when the food in the oven is burning.
- If you open the door, it causes an inow of oxygen and
may cause the food to ignite.
Do not apply excessive pressure to the door or the inside of the
appliance. Do not strike the door or the inside or the appliance.
- Hanging on to the door may result in the product falling
and cause serious injury.
- If the door is damaged, do not use the appliance. Contact a
service center.
NE59M4320_DG68-00882A-01_EN.indd 13 2/16/2017 3:45:24 PM
14 English
Important safety instructions
Important safety instructions
Do not hold food in your bare hands during or immediately
after cooking.
- Use cooking gloves. The food may be very hot and you
could burn yourself.
- Use a cooking glove or gloves, Handle and oven surfaces
may be hot enough to cause burns after cooking.
USAGE CAUTIONS
CAUTION
If the surface is cracked, turn the appliance off.
- Failing to do so may result in electric shock.
Dishes and containers can become hot. Handle with care.
Hot foods and steam can cause burns. Carefully remove container
coverings, directing the steam away your hands and face.
Remove lids from baby food jars before heating. After heating
baby food, stir well to distribute the heat evenly. Always test
the temperature by tasting before feeding the baby. The glass
jar or the surface of the food may appear to be cooler than the
interior, which can be hot enough to burn an infant’s mouth.
Take care as beverages or food may be very hot after heating.
- Especially when feeding a child. Check that it has cooled
sufciently.
Take care when heating liquids such as water or other beverages.
- Make sure to stir during or after cooking.
- Avoid using a slippery container with a narrow neck.
- Wait at least 30 seconds after heating before removing the
heated liquid.
- Failing to do so may result in an abrupt overow of the
contents and cause burns.
Do not stand on top of the appliance or place objects (such as
laundry, oven cover, lighted candles, lighted cigarettes, dishes,
chemicals, metal objects, etc.) on the appliance.
- Items, such as a cloth, may get caught in the door.
- This may result in electric shock, re, problems with the
product, or injury.
Do not operate the appliance with wet hands.
- This may result in electric shock.
Do not spray volatile substances such as insecticide onto the
surface of the appliance.
- As well as being harmful to humans, it may also result in
electric shock, re, or problems with the product.
Do not put your face or body close to the appliance while
cooking or when opening the door just after cooking.
- Take care that children do not come too close to the
appliance.
- Failing to do so may result in children burning themselves.
NE59M4320_DG68-00882A-01_EN.indd 14 2/16/2017 3:45:25 PM
English 15
Important safety instructions
Do not place food or heavy objects over the edge of the oven
door.
- If you open the door, the food or object may fall and this
may result in burns or injury.
Do not abruptly cool the door, the inside of the appliance, or a
dish by pouring water over it during or just after cooking.
- This may result in damage to the appliance. The steam or
water spray may result in burns or injury.
Do not operate while empty except for self-cleaning.
Do not defrost frozen beverages in narrow-necked bottles.
The bottles can break.
Do not scratch the glass of the oven door with a sharp object.
- This may result in the glass being damaged or broken.
Do not store anything directly on top of the appliance when it
is in operation.
Do not use sealed containers. Remove seals and lids before
cooking. Sealed containers can explode due to the build up of
pressure even after the oven has been turned off.
Take care that food you are cooking in the oven does not
come into contact with the heating element.
- This may result in re.
Do not over-heat food.
- Overheating food may result in re.
CRITICAL CLEANING WARNINGS
CAUTION
Do not clean the appliance by spraying water directly on to it.
Do not use benzene, thinner, or alcohol to clean the appliance.
- This may result in discoloration, deformation, damage,
electric shock, or re.
Take care not to hurt yourself when cleaning the appliance
(externally or internally).
- You may hurt yourself on the sharp edges of the appliance.
Do not clean the appliance with a steam cleaner.
- This may result in corrosion.
Keep the inside of the oven clean. Food particles or spattered
oils stuck to the oven walls or oor can cause paint damage
and reduce the efciency of the oven.
NE59M4320_DG68-00882A-01_EN.indd 15 2/16/2017 3:45:25 PM
16 English
Introducing your new range
Introducing your new range
Overview
05
02
03
04
06
07
08
09
10
11
01
01 Oven control panel
(See page 22 for
more information)
02 Glass surface 03 Oven door
04 Storage drawer 05 * Surface control
knobs
(See page 18 for
more information)
06 Self/steam clean
latch
07 Automatic oven
light switch
08 * Oven light 09 Convection fan
10 Shelf position 11 Gasket
What’s included with your range
* Wire racks (2)
NOTE
If you need an accessory marked with a *, you can buy it from the Samsung
Contact Center (1-800-726-7864).
NE59M4320_DG68-00882A-01_EN.indd 16 2/16/2017 3:45:25 PM
English 17
Before you begin
Before you begin
Clean the oven thoroughly before using it for the rst time. Then, remove the
accessories, set the oven to bake, and then run the oven at 400 °F for 1 hour.
There will be a distinctive odor. This is normal.
Ensure your kitchen is well ventilated during this conditioning period.
Energy saving tips
During cooking, the oven door should remain closed except when you turn
food over.
Do not open the door frequently during cooking to maintain the oven
temperature and to save energy.
If cooking time is more than 30 minutes, you can switch the oven off
5-10 minutes before the end of the cooking time to save energy. The residual
heat will complete the cooking process.
To save energy and reduce the time needed for re-heating the oven, plan oven
use to avoid turning the oven off between cooking one item and the next.
Whenever possible, cook more than one item at a time.
Cooktop cooking
About cooktop cooking
CAUTION
BEFORE COOKING
Do not use the glass cooktop surface as a cutting board.
Do not place or store items that can melt or catch re on the glass cooktop,
even when it is not being used.
Turn the surface units on only after placing cookware on them.
Do not store heavy items above the cooktop surface. They could fall and
damage it.
CAUTION
DURING COOKING
Do not place aluminum foil or plastic items such as salt and pepper shakers,
spoon holders, or plastic wrappings on the range when it is in use. The hot air
from the vent could melt plastics or ignite ammable items.
Make sure the correct surface unit is turned on.
Never cook directly on the glass. Always use cookware.
Always place the pan in the center of the surface unit you are cooking on.
Never leave surface units unattended while using a high heat setting.
Boilovers cause smoking and greasy spillovers that may catch on re.
Turn the surface units off before removing cookware.
Do not use plastic wrap to cover food. Plastic may melt onto the surface and
be very difcult to remove.
NE59M4320_DG68-00882A-01_EN.indd 17 2/16/2017 3:45:26 PM
18 English
Cooktop cooking
Cooktop cooking
Location of the radiant surface elements and controls
The radiant control knobs operate the radiant surface elements on the cooktop as
shown below.
01
02
06 07
05
04
03
01 Left Front:
6”/9”, 3000 W
02 Left Rear:
6”, 1200 W
03 Right Front:
9”/12”, 3000 W
04 Right Rear:
6”, 1200 W
05 Warming Center:
100 W
06 Hot surface
indicator
07 Cooktop on
indicator
CAUTION
AFTER COOKING
Do not touch the surface units until they have cooled down.
The surface may be still be hot and burns may occur if you touch the glass
surface before it has cooled down sufciently.
Immediately clean spills on the cooking area to prevent a tough cleaners,
chore later.
If cabinet storage is provided directly above the cooking surface, make sure
that the items are infrequently used and can be safely stored in an area
subjected to heat. Temperatures may be unsafe for items such as volatile
liquids, cleaners or aerosol sprays.
About the radiant surface elements
The temperature rises gradually and evenly. As the temperature rises, the radiant
element will glow red. To maintain the selected setting, the element will cycle
on and off. The heating element retains enough heat to provide a uniform and
consistent heat during the off cycle. For efcient cooking, turn off the element
several minutes before cooking is complete. This will allow residual heat to
complete the cooking process.
NOTE
Radiant elements have a limiter that allows the element to cycle ON and OFF, even
at the HI setting. This helps to prevent damage to the ceramic cooktop. Cycling at
the HI setting is normal and can occur if the cookware is too small for the radiant
element or if the cookware bottom is not at.
NE59M4320_DG68-00882A-01_EN.indd 18 2/16/2017 3:45:26 PM
English 19
Cooktop cooking
Hot surface indicator
Comes on when the unit is turned on or hot to the touch.
Stays on even after the unit is turned off.
Glows until the unit is cooled to approximately 150 °F.
Cooking areas
The cooking areas on your range are identied by permanent circles on the
glass cooking surface. For the most efcient cooking, t the pan size to the
element size.
Pans should not extend more than ½” to 1” beyond the cooking area.
When a control is turned on, a glow can be seen through the glass cooking
surface. The element will cycle on and off to maintain the preset heat setting,
even at high settings.
For more information on selecting proper types of cookware, refer to the
section “Using the proper cookware” on page 20.
How to set the appliance for cooktop cooking
CAUTION
The surface elements may be hot and burns may occur. Do not touch the
surface elements until they have cooled down sufciently.
At high or medium-high settings, never leave food unattended. Boilovers
cause smoking and greasy spillovers may catch on re.
Be sure you turn the control knob to OFF when you nish cooking.
Surface unit control knob
1
2
A
B
1
2
Single
(Left rear, Right rear)
Dual
(Left front, Right front)
1. Push the knob in.
2. Turn in either direction to the setting you want.
Position A : Single burner
Position B : Dual burner
CAUTION
The area between the high and off settings is not appropriate for cooking.
Recommended settings
SETTING TYPE OF COOKING
HIGH Starting most foods, bringing water to a boil, pan broiling
MEDIUM HIGH Continuing a rapid boil, frying, deep fat frying
MEDIUM
Maintaining a slow boil, thickening sauces and gravies,
steaming vegetables
MEDIUM LOW Keeping foods cooking, poaching, stewing
LOW Keeping food warm, melting, simmering
NE59M4320_DG68-00882A-01_EN.indd 19 2/16/2017 3:45:27 PM
20 English
Cooktop cooking
Cooktop cooking
Using the proper cookware
Using the right cookware can prevent many problems, such as uneven cooking or
extended cooking times. Using the proper pans will reduce cooking times and cook
food more evenly.
Check for atness by rotating a ruler across
the bottom of the cookware.
CORRECT INCORRECT
Flat bottom and straight sides.
Tight tting lids.
Weight of handle does not tilt
pan.
Pan is well balanced.
Pan size matches the amount
of food to be prepared and the
size of the surface element.
Made of a material that
conducts heat well.
Always match pot diameter to
element surface diameter.
Curved and warped pan bottoms.
Pan overhangs element by more
than one-half inch.
Pan is smaller than element.
Heavy handle tilts pan.
Using the warming center
The Warming Center, located in the back center of the glass surface, will keep hot,
cooked food at serving temperature.
NOTE
The surface warmer will not glow red like the cooking elements.
CAUTION
Do not warm food on the warming center for more than two hours.
U
se only cookware and dishes recommended as safe for oven and cooktop use.
Always use potholders or oven mitts when removing food from the warming
center as cookware and plates will be hot.
When warming pastries and breads, the cover should have an opening to
allow moisture to escape.
Always start with hot food. Eating uncooked or cold food placed on the
warming center could result in illness.
1. Turn the warming center on. Press the Warming Center On/Off pad.
2. Select the power setting you want. Pressing the Warming Center Level pad
once will set it to the Lo setting.
Press the pad twice for the Med setting, 3 times for Hi.
3. Turn the warming center off. Press the Warming Center On/Off pad.
NOTE
Pressing the OFF/CLEAR pad does not turn the warming center off.
For best results, all foods on the warming center should be covered with a
lid or aluminum foil. When warming pastries or breads, the cover should be
vented to allow moisture to escape.
Recommended settings
LEVEL TYPE OF FOOD
LO Breads/Pastries, Casseroles, Gravies, Eggs
MED
Dinner plate with food, Soups (cream), Vegetables, Sauces, Stews, Meats
HI Fried foods, Soups (liquid), Hot beverages
NE59M4320_DG68-00882A-01_EN.indd 20 2/16/2017 3:45:28 PM
English 21
Cooktop cooking
Choosing the proper cookware
What your cookware is made of determines how evenly and quickly heat is
transferred from the surface element to the pan bottom.
ALUMINUM - Excellent heat conductor. Some types of food will cause the
aluminum to darken. (Anodized aluminum cookware resists staining & pitting.).
If aluminum pans are slid across the ceramic cooktop, they may leave metal
marks that resemble scratches. Remove these marks as soon as the cooktop
cools down.
COPPER - Excellent heat conductor but discolors easily. May leave metal
marks on ceramic glass (see above).
STAINLESS STEEL - Slow heat conductor with uneven cooking results. Is
durable, easy to clean and resists staining.
C
AST IRON - A poor conductor; retains heat very well. Cooks evenly once
cooking temperature is reached. Not recommended for use on ceramic cooktops.
ENAMELWARE - Heating characteristics will vary depending on the base
material. Porcelain enamel coating must be smooth to avoid scratching
ceramic cooktops.
GLASS - Slow heat conductor. Not recommended for ceramic cooktop surfaces
because it may scratch the glass.
Protecting the smoothtop
Cleaning
Clean the cooktop before using it for the rst time.
Clean your cooktop daily or after each use. This will keep your cooktop
looking good and can prevent damage.
If a spillover occurs while you are cooking, immediately clean the spill from
the cooking area while it is hot to prevent a tough cleaning chore later. Using
extreme care, wipe the spill with a clean dry towel.
Do not allow spills to remain on the cooking area or the cooktop trim for a
long period of time.
Do not use abrasive cleansing powders or scouring pads which will scratch the
cooktop.
Do not use chlorine bleach, ammonia, or other cleansers not specically
recommended for use on a glass-ceramic surface.
Preventing marks and scratches
Do not use glass cookware. It may scratch the cooktop.
Do not place a trivet or wok ring between the cooktop and the pan.
These items can mark or scratch the cooktop.
Make sure the cooktop and the pan bottom are clean.
Do not slide metal pans across the cooktop.
Preventing stains
Do not use a soiled dish cloth or sponge to clean the cooktop surface.
A lm will remain, which may cause stains on the cooking surface after the
area is heated.
Continuously cooking on a soiled surface can result in a permanent stain.
Preventing other damage
Do not allow plastic, sugar, or foods with high sugar content to melt onto the
hot cooktop. Should this happen, clean immediately.
Do not let a pan boil dry as this will damage the cooktop and the pan.
Do not use the cooktop as a work surface or cutting board.
Do not cook food directly on the cooktop. Always use the proper cookware.
NE59M4320_DG68-00882A-01_EN.indd 21 2/16/2017 3:45:28 PM
22 English
Operating the oven
12 COOKING TIME: Press, and then use the number pad to set the amount of time
you want your food to cook. The oven will shut off when the cooking time has
run out.
13 DELAY START: Press to set the oven to start and stop automatically at a time
you set. (Bake, Conv.bake/Roast, Cooking Time, and self clean only.)
14 CLOCK: Use to set the time of day.
15 LAMP: Press to turn the oven light on or off.
16 START/SET: Press to start any cooking or cleaning function in the oven.
17 OFF/CLEAR: Press to cancel all oven operations except the clock and timer.
Operating the oven
The oven control panel
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For satisfactory
use of your oven, become familiar with the various features and functions of the
oven as described below. Detailed instructions for each feature and function follow
later in this user manual.
03 07 04
08
05 06 01
1110 12 13 14 17 15
02 1609
01 DISPLAY: Shows the time of day, oven temperature, whether the oven is in the
bake, broil or self-cleaning mode, and the time set for the timer or automatic
oven operations.
02 NUMBER PAD: Use to set any function requiring numbers such as the time of
day on the clock, the timer, the oven temperature, the start time, and length of
operation for timed baking.
03 CONVECTION BAKE: Use to select the Convection bake function of the oven.
04 CONVECTION ROAST: Use to select the Convection roast function of the oven.
05 BAKE: Use to select the bake function of the oven.
06 BROIL: Use to select the broil function of the oven.
07 KEEP WARM: Use to select the keep warm function of the oven to keep cooked
foods warm.
08 STEAM CLEAN: Use to select the steam cleaning function of the oven.
09 SELF CLEAN: Use to select the Self-cleaning function of the oven.
10 EASY COOK: Use to recall the easy cook recipe setting of the oven.
11 TIMER ON/OFF: Use to set or cancel the minute timer. The minute timer does
not start or stop cooking.
NE59M4320_DG68-00882A-01_EN.indd 22 2/16/2017 3:45:29 PM
English 23
Operating the oven
Setting the clock
The clock must be set to the correct time of day for the automatic oven timing
functions to work properly.
The time of day cannot be changed during a timed cooking, a delay-timed
cooking, or a self-cleaning cycle.
This model is set only 12-hour.
How to set the clock
1. Start the setup. Press Clock.
2. Enter the current time in hours and minutes on the number pad, eg.
1, 3, 0, for 1:30.
3. Press Clock or START/SET to save the changes.
Setting the kitchen timer
The kitchen timer serves as an extra timer that will beep when the set time has
elapsed. It does not start or stop cooking functions. You can use the kitchen timer
with any of the other oven functions.
How to set the timer
1. Turn the timer on. Press Timer On/Off.
2. Enter the amount of time you want. Enter the amount of time you want using
the number pad, eg. 1, 5. The timer can be set for any amount of time from
1 minute to 9 hours and 59 minutes.
If you make a mistake, press Timer On/Off and enter the amount of time again.
3. Start the timer. Press Timer On/Off.
4. When the set time has elapsed, the oven will beep and the display will show
End until you press Timer On/Off pad. You can cancel the timer at any time by
pressing Timer On/Off.
NE59M4320_DG68-00882A-01_EN.indd 23 2/16/2017 3:45:29 PM
24 English
Operating the oven
Operating the oven
Delay start
In a delay timed cooking, the oven’s timer turns the oven on and off at times you
select in advance.
You can use the delay start feature only with another cooking operation
(bake, convection bake, convection roast, slow cook, or dehydrate).
You can set the oven for a delay start before setting other cooking operations.
The clock must be set to the current time.
How to set the oven for delay start
1. Position the oven rack(s) and place the food in the oven.
2. Enter the setup. Press the pad for the cooking operation you want, eg. Bake.
The default temperature is 350 °F.
3. Use the number pad to enter the temperature you want, eg. 375 °F.
4. Press Cooking Time.
5. Enter the cooking time you want, eg. 45 min, using the number pad.
You can set the cooking time for any amount of time from 1 minute to 9 hours
and 59 minutes.
6. Press Delay Start.
7. Enter the time you want the oven to turn on, eg. 4:30, using the number pad.
8. Press START/SET. At the set time, a short beep will sound. The oven will begin
to bake.
Timed cooking
In timed cooking, the oven turns on immediately and cooks for the length of time
you select. At the end of the cooking time, the oven turns off automatically.
You can use the timed cooking feature only with another cooking operation
(bake, convection bake, convection roast, slow cook, or dehydrate).
How to set the oven for timed cooking
1. Enter the setup. Press the pad for the cooking operation you want, eg. Bake.
The default temperature is 350 °F.
2. Enter the temperature you want, eg. 375 °F, using the number pad.
3. Press Cooking Time.
4. Enter the cooking time you want, eg. 45 min, using the number pad.
You can set the cooking time for any amount of time from 1 minute to 9 hours
and 59 minutes.
5. Press START/SET to begin cooking. The temperature display will start to
change once the oven temperature reaches 175 °F.
The oven will continue to cook until the set amount of time has elapsed, then
turn off automatically unless you set the keep warm feature. (Refer to the
section on the keep warm feature on page 30.)
6. You can cancel a cook time at any time by setting cook time 0 min.
(Press Cooking Time -> enter 0 -> press START/SET)
When the timed cooking is done, the range will beep 10 times.
CAUTION
Use caution with the timed cooking or delay start features. Use these features to
cook cured or frozen meats and most fruits and vegetables. Foods that can easily
spoil, such as milk, eggs, sh, meat, or poultry, should be chilled in the refrigerator
rst. Even when chilled, they should not stand in the oven for more than 1 hour
before cooking begins, and should be removed promptly when cooking is
completed. Eating spoiled food can result in sickness from food poisoning.
NE59M4320_DG68-00882A-01_EN.indd 24 2/16/2017 3:45:29 PM
English 25
Operating the oven
Turning the oven light on and off
The oven light turns on automatically when the door is opened.
The oven light turns off automatically when the door is closed.
You can turn the oven light on and off manually by pressing the pad.
Minimum and maximum settings
All of the features listed in the table below have minimum and maximum time
or temperature settings. A beep will sound each time a pad on the control panel
is pressed and the entry is accepted. An error tone will sound in the form of a
long beep if the entered temperature or time is below the minimum or above the
maximum setting for the feature.
FEATURE MINIMUM MAXIMUM
Bake 175 °F (80 °C) 550 °F (285 °C)
Broil
LO HI
Convection Bake 175 °F (80 °C) 550 °F (285 °C)
Convection Roast 175 °F (80 °C) 550 °F (285 °C)
Warming Center - 3 Hr.
Keep Warm - 3 Hr.
Proof - 12 Hr.
Self Clean 2 Hr. 5 Hr.
Steam Clean 20 Min. 20 Min.
Using the oven racks
Oven rack positions
1
2
3
4
5
6
7
Recommended rack position for cooking
Type of food Rack Position
Broiling hamburgers 7
Broiling meats or Small
cuts of poultry, Fish
5-7
Bundt caked, Pound
cakes, Frozen pies,
Casseroles
4 or 3
Angel food cakes, Small
roasts
2
Turkey, Large roasts,
Hams, Fresh pizza
1
This table is for reference only.
NE59M4320_DG68-00882A-01_EN.indd 25 2/16/2017 3:45:29 PM
26 English
Operating the oven
Operating the oven
Rack and Pan placement
3 4
Single Oven Rack
or
Centering the baking pans in the oven
as much as possible will produce better
results. If baking with more than one pan,
place the pans so each has at least 1˝ to
1½˝ of air space around it.
When baking on a single oven rack, place
the oven rack in position 3 or 4. See the
gure on the left.
5
3
Multiple Oven Rack
When baking cakes and cookies on
multiple racks, place the oven racks in
positions 3 and 5. See the gure on the left.
Using Multiple Oven Racks
Type of Baking Rack Position
Cakes and Cookies 3 and 5
Before using the racks
The oven has two racks.
Each rack has stops that need to be placed correctly on the supports. These stops
will keep the rack from coming completely out.
REMOVING THE RACKS
1. Pull the rack straight out until it stops.
2. Lift up the front of the rack, and then pull it out.
REPLACING THE RACKS
1. Place the end of the rack on the support.
2. Tilt the front end up and push the rack in.
CAUTION
Do not cover a rack with aluminum foil or place aluminum foil on the oven
bottom. This will hamper heat circulation, resulting in poor baking, and may
damage the oven bottom.
Arrange the oven racks only when the oven is cool.
Baking
The oven can be programmed to bake at any temperature from 175 °F to 550 °F.
Baking temperature and time will vary depending on the ingredients and the size
and shape of the baking pan used. Dark or nonstick coatings may cook faster with
more browning.
How to set the temperature
1. Start the set up. Press Bake. The default temperature is 350 °F.
2. Enter the temperature you want on the number pad, eg. 3, 7, 5.
3. Start the bake function. Press START/SET. The temperature display will start to
change once the oven temperature reaches 175 °F.
4. If you want to cancel baking or if you have nished, press OFF/CLEAR.
Place food in the oven after preheating if the recipe calls for it. Preheating
is very important for good results when baking cakes, cookies, pastry, and
breads. After the oven has reached the desired temperature, the range will
beep 6 times.
NOTE
For performance reasons, the convection fan may be turned on or off during the
operation.
NE59M4320_DG68-00882A-01_EN.indd 26 2/16/2017 3:45:30 PM
English 27
Operating the oven
How to adjust the temperature while cooking
1. Start the setup.
Press Bake. The display will show the present temperature, eg. 375 °F.
2. Enter the temperature you want, eg. 425 °F, using the number pad.
3. Complete the entry by pressing START/SET.
Convection baking
1
2
3
4
5
6
7
By using the convection bake feature, you
will be able to cook faster. You can program
the oven for convection baking at any
temperature between 175 °F and 550 °F.
Convection baking uses a fan to circulate
the oven’s heat evenly and continuously
within the oven. This improved heat
distribution allows for even cooking and
excellent results using multiple racks at the
same time. Foods cooked on a single oven
rack will generally cook faster and more
evenly with convection baking. Multiple
oven rack cooking may slightly increase
cook times for some foods, but the overall
result is time saved. Breads and pastries
brown more evenly.
Tips for convection baking
The amount of time you save will vary depending on the amount and type of food
you are cooking. When baking cookies or biscuits, you should use pans with no
sides or very low sides to allow the heated air to circulate around the food. Using
a pan with a dark nish will allow faster cooking times.
When using convection baking with a single rack, place the oven rack in position
3 or 4. If cooking on multiple racks, place the oven racks in position 3 and 5.
When baking a cake, using the bake mode will produce better results.
How to set the oven for convection baking
1. Start the convection baking mode.
Press Bake. The default temperature is 350 °F.
2. Enter the temperature you want, eg. 400 °F, using the number pad.
3. Press START/SET to begin convection baking.
Conv. Bake and the adjusted oven temperature, eg. 400 °F, will appear in the
display for 2 seconds.
The temperature display will start to change once the oven temperature
reaches 175 °F.
The range will beep 6 times when the oven reaches the adjusted oven
temperature.
4. To turn off or cancel convection baking, press OFF/CLEAR.
The convection oven fan shuts off when the oven door is opened.
DO NOT leave the door open for long periods of time while using convection
cooking or you may shorten the life of the convection heating element.
NOTE
For performance reasons, the convection fan may be turned on or off during the
operation.
NE59M4320_DG68-00882A-01_EN.indd 27 2/16/2017 3:45:30 PM
28 English
Operating the oven
Operating the oven
Broiling
Broil mode is best for meats, sh, and poultry up to 1” thick. Broiling is a method
of cooking tender cuts of meat by direct heat under the broil element of the oven.
The high heat cooks quickly and gives a rich, brown outer appearance.
Broil stop position
Broil stop position
Leave the door open at the broil stop
position. The door will stay open by itself,
yet the proper temperature is maintained in
the oven.
CAUTION
Should an oven re occur, close the oven
door and turn the oven off. If the re
continues, throw baking soda on the re
or use a foam-type re extinguisher. Do
not put water or our on the re. Flour can
explode and water can cause a grease re
to spread and cause personal injury.
How to set the oven for broiling
1. Select the broil setting you want. Press Broil once for HI or twice for LO.
Use LO to cook foods such as poultry or thick cuts of meat thoroughly without
over-browning them.
2. Start the broiling function. Press START/SET.
Broil one side until the food is browned. Turn over and broil the other side.
3. Press OFF/CLEAR once you have nished cooking or if you want to cancel
broiling.
Convection roasting
Convection roasting is good for cooking large tender cuts of meat, uncovered.
Heat comes from the top heating element. The convection fan circulates the heated
air evenly over and around the food. Meat and poultry are browned on all sides
as if they were cooked on a rotisserie. The heated air seals in juices quickly for a
moist and tender product while, at the same time, creating a rich golden brown
exterior.
How to set the oven for convection roasting
1. Start the convection roasting mode.
Press Roast. The default temperature is 350 °F.
2. Enter the temperature you want, eg. 400 °F, using the number pad.
3. Press START/SET to begin convection roasting.
Conv. Roast and the adjusted oven temperature, eg. 400 °F, will appear in the
display for 2 seconds. The temperature display will start to change once the
oven temperature reaches 175 °F. The range will beep 6 times when the oven
reaches the adjusted oven temperature.
4. To turn off or cancel convection roasting, press OFF/CLEAR.
The convection oven fan shuts off when the oven door is opened.
DO NOT leave the door open for long periods of time while using convection
cooking or you may shorten the life of the convection heating element.
NOTE
For performance reasons, the convection fan may be turned on or off during the
operation.
NE59M4320_DG68-00882A-01_EN.indd 28 2/16/2017 3:45:30 PM
English 29
Operating the oven
Broiling recommendation guide
The size, weight, thickness, starting temperature, and your doneness preference
will affect broiling times. This guide is based on meats at refrigerator temperature.
Always use a broiler pan and its grid when broiling. Always preheat the oven for
5 minutes before broiling.
Food Doneness Size Thickness
Broil
setting
Rack
position
Cooking time (Minutes)
1st side 2nd side
Hamburgers
Medium 9 patties 1” HI 7 3:40 2:40
Medium 9 patties ¾” HI 7 3:20 2:20
Toast
- 9 slices - HI 7 0:32 0:30
- 9 slices - HI 6 1:00 0:45
Beef steaks
Rare - 1” HI 7 3:00-3:30 2:00-2:30
Medium - 1” HI 6 4:30-5:00 3:30-4:00
Well done - 1” HI 5 8:00-9:00 6:00-7:00
Rare - 1½” HI 7 3:30-4:00 2:30-3:00
Medium - 1½” HI 6 5:30-6:00 4:30-5:00
Well done - 1½” HI 5 12:00-14:00 10:00-12:00
Chicken
pieces
Well done 4.5 lbs. ¾”-1” LO 4 18:00-20:00 16:00-18:00
Well done 2-2½ lbs. ¾”-1” LO 4 15:00-18:00 13:00-16:00
Pork chops Well done 1 lb. ½” HI 5 8:00-8:30 6:30-7:00
Lamb chops
Medium 10 oz. 1” LO 4 5:00-6:00 4:00-5:00
Well done 1 lb. 1½” LO 4 7:00-8:00 6:00-7:00
Fish llets Well done - ¼-½” LO 5 5:00-7:00 4:00-5:00
Ham slices
(precooked)
- - 1½” HI 4 4:00-5:00 3:00-4:00
Using the easy cook feature
Slow Cook
The Slow Cook feature cooks food more slowly at lower oven temperatures.
The extended cooking times allow better distribution of avors in many recipes.
This feature is ideal for roasting beef, pork & poultry. Slow cooking meats may
cause the exterior of meats to become dark but not burnt. This is normal.
1. Press Slow Cook once for HI or twice for LO.
2. Press START/SET.
NOTE
Use only 1 rack and place the rack in position 1 or 2 for the best results.
Preheating the oven is not necessary.
Bread Proof
The Bread Proof function automatically provides the optimum temperature for the
bread proof process, and therefore does not have a temperature adjustment.
If you press Bread Proof when the oven temperature is above 100 °F, Hot will
appear in the display. Because these functions produce the best results when
started while the oven is cool, we recommend that you wait until the oven has
cooled down and Hot disappears from the display.
1. Press Bread Proof.
2. Press START/SET.
3. Press OFF/CLEAR at any time to turn off the Bread Proof feature.
NOTE
Use rack position 3 for bread proong.
NE59M4320_DG68-00882A-01_EN.indd 29 2/16/2017 3:45:31 PM
30 English
Operating the oven
Operating the oven
Using the keep warm feature
The keep warm feature will keep cooked food warm for serving up to 3 hours after
cooking has nished.
After 3 hours, the feature will shut the oven off automatically. The feature may be
used without any other cooking operations or may be set to activate after a timed
or delay timed cooking operation.
You should not use this feature to reheat cold foods.
How to use the keep warm feature
1. Press Keep Warm.
2. Press START/SET.
3. Press OFF/CLEAR at any time to turn the feature off.
How to set the oven to activate the keep warm mode after a timed cooking
1. Set up the oven for Timed cooking.
(Refer to the section on the time cooking feature on pages 24.)
2. Press Keep Warm before pressing START/SET to begin cooking.
3. Press OFF/CLEAR at any time to turn the feature off.
Dehydrate
Dehydrate dries food or removes moisture from food via heat circulation. After
drying the food, keep it in a cool and dry place. For fruit, adding lemon (or
pineapple) juice or sprinkling sugar on the fruit will help fruit retain sweetness.
1. Press Dehydrate. The default temperature is 150 °F.
2. Enter the temperature you want on number pad. (100 °F - 175 °F)
3. Press START/SET.
Category Rack position Temperature (˚F)
Vegerables of Fruits 3 or 4 100-150
Meat 3 or 4 145-175
NOTE
Drying time depends on the moisture content of the food, the size of the food,
and the atmospheric humidity.
Preheating the oven is not necessary.
NE59M4320_DG68-00882A-01_EN.indd 30 2/16/2017 3:45:31 PM
English 31
Operating the oven
Using the sabbath feature
(For use on the Jewish Sabbath & Holidays)
K
For further assistance, guidelines for proper usage, and a complete list
of models with the Sabbath feature, please visit the web at
http:\\www.star-k.org.
You can use the Sabbath feature with baking only. The oven temperature may
be set higher or lower after setting the Sabbath feature. (The oven temperature
adjustment feature should be used only during Jewish holidays.) The display,
however, will not change and tones will not sound when a change occurs.
Once the oven is properly set for baking with the Sabbath feature active, the
oven will remain continuously on until the Sabbath feature is cancelled. This will
override the factory preset 12 hour energy saving feature. If the oven light is
needed during the Sabbath, press before activating the Sabbath feature.
Once the oven light is turned on and the Sabbath feature is active, the oven light
will remain on until the Sabbath feature is turned off. If the oven light needs to be
off, be sure to turn the oven light off before activating the Sabbath feature.
How to use the Sabbath feature
1. Press Bake. The default temperature is 350 °F.
2. Enter the temperature you want, eg. 375 °F, by using the number pad.
3. Press START/SET. The temperature display will start to change once the oven
temperature reaches 175 °F.
4. Press Bake and 1 at the same time for 3 seconds. The display will show SAb.
Once SAb appears in the display, the oven will not beep or display any further
changes. You may change the oven temperature once baking has started.
Remember that the oven will not beep or display any further changes once
the Sabbath feature is engaged.
5. You can turn the oven off at any time by pressing OFF/CLEAR. This will turn
only the oven off. If you want to deactivate the Sabbath feature, hold down
Bake and 1 at the same time for 3 seconds. Sab will disappear from the
display.
Do not to attempt to activate any other program feature except BAKE while
the Sabbath feature is active. ONLY the following key pads will function
correctly with the Sabbath feature on: NUMBER, BAKE, START/SET and OFF/
CLEAR. ALL OTHER KEYPADS should not be used once the Sabbath feature is
activated.
You can change the oven temperature, but the display will not change
and tones will not sound when a change occurs. (The oven temperature
adjustment feature should be used only on Jewish holidays.) After changing
the temperature while the unit is in Sabbath mode there is a 15 seconds
delay before the unit will recognize the change.
You can set the Cook time function before activating the Sabbath feature.
Should you experience a power failure or interruption, the oven will shut off.
When power is returned, the oven will not turn back on automatically. SAb
will be displayed in the oven control display, but the oven will not operate.
Food may be safely removed from the oven while it is still in the Sabbath
mode, however the oven cannot be turned back on until after the Sabbath/
Holidays. After the Sabbath observance, turn OFF the Sabbath mode. Press
and hold both BAKE and 1 for at least 3 seconds simultaneously to turn the
Sabbath mode off. The oven may then be used with all normal functions.
Do not open the oven door or change the oven temperature for about
30 minutes after you have started Sabbath mode to allow the oven to reach
the set temperature. Note that, for best performance, the oven fan operates
only when the oven temperature is rising.
Do not use the cooktop when the oven is in the Sabbath MODE.
NE59M4320_DG68-00882A-01_EN.indd 31 2/16/2017 3:45:31 PM
32 English
Operating the oven
Operating the oven
Extra features
Thermostat adjustment
The temperature in the oven has been preset at the factory. When rst using the
oven, be sure to follow recipe times and temperatures. If you think the oven is
too hot or too cool, the temperature in the oven can be adjusted. Before adjusting,
test a recipe by using a temperature setting that is higher or lower than the
recommended temperature. The baking results should help you to decide how
much of an adjustment is needed.
The oven temperature can be adjusted ±35 °F (±19 °C).
How to adjust the oven temperature
1. Press Broil and 1 at the same time for 3 seconds.
The display will show 0.
2. Enter the adjustment you want, eg. 20 °F, using the number pad.
You can adjust the temperature so that it is lower than the factory setting by
pressing Broil.
3. Press START/SET.
NOTE
This adjustment will not affect the broiling or the self-cleaning temperatures. The
adjustment will be retained in memory after a power failure.
Convection auto conversion feature
When you use the auto conversion feature, the convection auto conversion feature
will automatically convert entered regular baking temperatures to convection
baking temperatures.
If this feature is activated, the display will show the actual converted (reduced)
temperature. For example, if you enter a regular recipe temperature of 350 °F and
press START/SET, the display will show the converted temperature of 325 °F.
How to disable or enable the auto conversion feature
1. Press Broil and 3 at the same time for 3 seconds.
The display will show On (enabled) or OFF (disabled).
The default setting is Con OFF.
2. Press 0 to select Con On or Con OFF.
Pressing 0 changes the mode between Con On and Con OFF.
3. Press START/SET.
NE59M4320_DG68-00882A-01_EN.indd 32 2/16/2017 3:45:31 PM
English 33
Operating the oven
Sound on/off
By using this feature, you can set the oven controls to operate silently.
How to turn the sound on or off
1. Press Broil and 6 at the same time for 3 seconds.
The display will show On (sound on) or OFF (sound off).
The default setting is Snd On.
2. Press 0 to select Snd OFF or Snd On.
Pressing 0 changes the mode between Snd On and Snd OFF.
3. Press START/SET.
Demo mode
This option is for use by retail establishments for display purposes only.
(The heating element does not operate.)
How to enable or disable the demo mode
1. Press Broil and 7.
2. Pressing 0 changes the mode between On and OFF.
3. Press START/SET.
Control lockout
This feature lets you lock the buttons on the touch pad so they cannot be activated
accidentally.
How to activate the control lockout feature
1. Press START/SET for 3 seconds.
Loc and the Loc icon appear in the display, as well as the current time.
All functions must be cancelled before the control lockout is activated.
This function is available when the oven temperature is under 400°F.
How to unlock the controls
1. Press START/SET for 3 seconds.
Loc and the lock icon will disappear from the display.
NE59M4320_DG68-00882A-01_EN.indd 33 2/16/2017 3:45:31 PM
34 English
Maintaining your appliance
Maintaining your appliance
Self-cleaning
This self-cleaning oven uses high temperatures (well above cooking temperatures)
to burn off leftover grease and residue completely or reduce them to a nely
powdered ash that you can wipe away with a damp cloth.
CAUTION
During the self-cleaning cycle, the outside of the range will become very hot
to the touch. Do not leave small children unattended near the appliance.
Some birds are extremely sensitive to the fumes given off during the self-
cleaning cycle of any range. Move birds to another well-ventilated room.
Do not line the oven walls, racks, bottom, or any other part of the range with
aluminum foil. Doing so will result in poor heat distribution, poor baking
results, and cause permanent damage to the oven interior. Aluminum foil will
melt and adhere to the interior surface of the oven.
Do not force the oven door open. This can damage the automatic door locking
system. Use care when opening the oven door after the self-cleaning cycle is
complete. Stand to the side of the oven when opening the door to allow hot
air or steam to escape. The oven may still be VERY HOT.
Before a self-cleaning cycle
Fig. 1
We recommend venting your kitchen
with an open window or using a
ventilation fan or hood during the self-
cleaning cycle.
Remove the wire rack, broil pan, broil
pan insert, all cookware, and any
aluminum foil from the oven.
Wipe up debris from the oven bottom.
(Fig. 1)
The silver-colored oven racks can be
self-cleaned, but they will darken, lose
their luster, and become hard to slide.
Don’t hand
clean the oven
door gasket.
You may
hand clean
the door.
Fig. 2
Residue on the front frame of the
range and outside the gasket on the
door will need to be cleaned by hand.
Clean these areas with hot water, soap-
lled steel-wool pads, or cleansers such
as Soft Scrub. Rinse well with clean
water and dry.
Do not clean the gasket. The berglass
material of the oven door gasket
cannot withstand abrasion. It is
essential for the gasket to remain
intact. If you notice it becoming worn
or frayed, have it replaced. (Fig. 2)
Make sure the oven light bulb cover is
in place and the oven light is off.
NOTE
Remove oven racks and accessories before
starting the self-clean mode.
NE59M4320_DG68-00882A-01_EN.indd 34 2/16/2017 3:45:32 PM
English 35
Maintaining your appliance
How to run a self-cleaning cycle
1. Select the length of time for the self-cleaning operation, eg. 3 hours.
Press Self Clean once for a 3 hour clean time, twice for a 5 hour clean time,
or 3 times for a 2 hour clean time.
The default setting is 3 hours.
2. Start the self-cleaning cycle. Press START/SET. The motor-driven door lock will
engage automatically.
You will not be able to start a self-cleaning cycle if the control lockout
feature is activated or if the oven’s temperature is too hot.
The oven door locks automatically. The display will show the clean
time remaining. It is not be possible to open the oven door until the
temperature drops to a safe/cool temperature.
The self-cleaning feature will not operate when the warming center is on.
3. When the self-cleaning cycle is done, End will appear in the display and the
range will beep 6 times.
How to delay the start of self-cleaning
1. Press Self Clean. Select the desired self-clean time by pressing Self Clean.
2. Press Delay Start.
3. Enter the time you want the clean cycle to start.
4. Press START/SET. The display will show Delay, Self clean, and the Lock icon.
The motor-driven door lock will engage automatically.
5. The Self-Cleaning cycle will turn on automatically at the set time.
How to turn off the self-cleaning feature
You may nd it necessary to stop or interrupt a self-cleaning cycle due to smoke in
the oven.
1. Press OFF/CLEAR.
2. You will be able to open the oven door once the oven has cooled down for
approximately 1 hour.
After a self-cleaning cycle
You may notice some white ash in the oven. Wipe it up with a damp cloth
after the oven cools. (If white spots remain, remove them with a soap-lled
steel wool pad and rinse thoroughly with a vinegar and water mixture.)
If the oven is not clean after one cycle, repeat the cycle.
You cannot set the oven for cooking until the oven is cool enough for the door
to unlock.
NE59M4320_DG68-00882A-01_EN.indd 35 2/16/2017 3:45:32 PM
36 English
Maintaining your appliance
Maintaining your appliance
Steam-cleaning
How to set the oven for steam-cleaning
For light cleaning, the Steam-cleaning function saves time and energy. For heavier-
duty cleaning, use the self-cleaning function.
1. Remove all accessories from the oven.
2. Pour approximately 10 oz. (300 ml) of
water onto the bottom of the empty
oven and close the oven door.
Use normal water only, not distilled
water.
3. Press Steam Clean.
4. Press START/SET.
When the operation is complete, the
display will blink and a beep will
sound.
5. Press OFF/CLEAR.
6. Clean the oven’s interior.
There will be a signicant amount of
water remaining on the bottom of the
oven after a steam-cleaning cycle.
Remove the residual water with a
sponge or soft dry cloth.
When steam-cleaning, use exactly 10 oz. of water since this produces the
best results.
NOTE
If you press Steam Clean when the oven temperature is above 100˚F, Hot will
appear in the display. Because these functions produce the best results when
started while the oven is cool, we recommend that you wait until the oven has
cooled down and Hot disappears from the display.
After a steam-cleaning cycle
Take care when opening the door before a steam-cleaning procedure has
ended. The water on the bottom is hot.
Open the oven door and remove the remaining water with a sponge. Do not
leave the residual water in the oven for any length of time. Wipe the oven
clean and dry with a soft cloth. Do not forget to wipe under the oven door
seal.
Use a detergent-soaked sponge, a soft brush, or a nylon scrubber to wipe the
oven interior. Remove stubborn residue with a nylon scourer. You can remove
lime deposits with a cloth soaked in vinegar.
If the oven remains dirty, you can repeat the procedure once the oven has
cooled.
For heavy residue, such as grease left over from roasting, we recommend
that you rub detergent into the residue before activating the steam-cleaning
function.
After cleaning, leave the oven door ajar at a 15 ° angle to allow the interior
enamel surface to dry thoroughly.
Care and cleaning of the oven
WARNING
Be sure all controls are OFF and all surfaces are COOL before cleaning any part
of the range.
If your range is removed for cleaning, servicing, or any
reason, be sure the Anti-Tip device is re-engaged properly
when the range is replaced. If you fail to reengage the
Anti-Tip device, the range could tip and cause serous
injury.
NE59M4320_DG68-00882A-01_EN.indd 36 2/16/2017 3:45:32 PM
English 37
Maintaining your appliance
Oven vent
Oven vent
The oven vent is located above the
right rear surface unit.
This area could become hot during
oven use.
It is normal for steam to come out of
the vent.
The vent is important for proper air
circulation. Never block this vent.
Cleaning painted parts and decorative trim
For general cleaning, use a cloth with hot and soapy water.
For more difcult residue and built-up grease, apply a liquid detergent directly
onto the area and leave for 30 to 60 minutes. Wipe with a damp cloth and dry.
Do not use abrasive cleaners on any of these surfaces. They can scratch.
Cleaning stainless steel surfaces
1. Shake the bottle of Stainless Steel Appliance Cleaner or Polish well.
2. Place a small amount of stainless steel appliance cleaner or polish on a damp
cloth or damp paper towel.
3. Clean a small area, rubbing with the grain of the stainless steel if applicable.
4. Dry and buff with a clean, dry paper towel or soft cloth.
5. Repeat as necessary.
NOTE
Do not use a steel-wool pad. It will scratch the surface.
If a mineral oil-based stainless steel appliance cleaner has been used before to
clean the appliance, wash the surface with dishwashing liquid and water prior
to using the Stainless Steel Appliance Cleaner or Polish.
Oven racks
If the racks are left in the oven during a self-cleaning cycle, their color will
turn slightly blue and the nish will be dull. After the self-cleaning cycle is
complete and the oven has cooled, rub the sides of the racks with wax paper
or a cloth containing a small amount of oil. This will help the racks glide more
easily in their tracks.
Oven door
Don’t hand
clean the oven
door gasket.
You may
hand clean
the door.
Use soap & water to thoroughly clean
the top, sides, and front of the oven
door. Rinse well. You may use a glass
cleaner on the outside glass of the
oven door. DO NOT immerse the door
in water. DO NOT spray or allow water
or the glass cleaner to enter the door
vents. DO NOT use oven cleaners,
cleaning powders, or any harsh
abrasive cleaning materials on the
outside of the oven door.
DO NOT clean the oven door gasket.
The oven door gasket is made of a
woven material which is essential for a
good seal. Care should be taken not to
rub, damage, or remove this gasket.
NE59M4320_DG68-00882A-01_EN.indd 37 2/16/2017 3:45:33 PM
38 English
Maintaining your appliance
Maintaining your appliance
Care and cleaning of the glass cooktop
Normal daily use cleaning
Use only a ceramic cooktop cleaner. Other creams may not be as effective.
By following these steps, you can maintain and protect the surface of your glass
cooktop.
1. Before using the cooktop for the rst time, clean it with a ceramic cooktop
cleaner.
This helps protect the top and makes cleanup easier.
2. Daily use of a ceramic cooktop cleaner will help keep the cooktop looking new.
3. Shake the cleaning cream well. Apply a few drops of cleaner directly to the
cooktop.
4. Use a paper towel or a cleaning pad for ceramic cooktops to clean the entire
cooktop surface.
5. Use a dry cloth or paper towel to remove all cleaning residue. No need to
rinse.
WARNING
DAMAGE to your glass surface may occur if you use scrub pads other than those
recommended.
Removing burned-on residue
1. Allow the cooktop to cool.
2. Spread a few drops of ceramic cooktop
cleaner on the entire burned residue
area.
3. Using the cleaning pad for ceramic
cooktops, rub the residue area,
applying pressure as needed.
4. If any residue remains, repeat the steps
listed above as needed.
5. For additional protection, after all
residue has been removed, polish the
entire surface with ceramic cooktop
cleaner and a paper towel.
NE59M4320_DG68-00882A-01_EN.indd 38 2/16/2017 3:45:33 PM
English 39
Maintaining your appliance
Removing heavy, burned-on residue
1. Allow the cooktop to cool.
2. Use a single-edge razor-blade scraper
at approximately a 45° angle against
the glass surface and scrape the soil.
It will be necessary to apply pressure
to remove the residue.
3. After scraping with the razor scraper,
spread a few drops of ceramic cooktop
cleaner on the entire burned residue
area. Use the cleaning pad to remove
any remaining residue. (Do not scrape
the seal.)
4. For additional protection, after all
residue has been removed, polish the
entire surface with the cooktop cleaner
and a paper towel.
Removing metal marks and scratches
1. Be careful not to slide pots and pans across your cooktop. It will leave marks
on the cooktop surface. You can remove these marks by applying ceramic
cooktop cleaner with a cleaning pad for ceramic cooktops.
2. If pots with a thin overlay of aluminum or copper are allowed to boil dry, the
overlay may leave black discoloration on the cooktop. You should remove this
discoloration immediately or it may become permanent.
WARNING
Carefully check the bottoms of pans for roughness that may scratch the cooktop.
Cleaning the cooktop seal
To clean the seal around the edges of
the glass, lay a wet cloth on it for a
few minutes, then wipe clean with a
nonabrasive cleaner.
Potential for permanent damage to the glass surface
Sugary spillovers (such as jellies, fudge, candy, syrups) or melted plastics can
cause pitting of the surface of your cooktop. This is not covered under the
warranty. You should clean the spill while it is still hot. Take special care when
removing hot substances. Refer to the following section.
When using a scraper, be sure it is new and the razor blade is still sharp.
Do not use a dull or nicked blade.
Cleaning sugary spills and melted plastic
1. Turn off all surface units. Remove hot pans.
2. Wearing an oven mitt, use a single-edge razor-blade scraper to move the spill
to a cool area of the cooktop. Remove the spill with paper towels.
3. Any remaining spillover should be left until the surface of the cooktop has
cooled.
4. Don’t use the surface units again until all of the residue has been completely
removed.
NOTE
If pitting or indentations in the glass surface have already occurred, the cooktop
glass will have to be replaced. In this case, service will be necessary.
NE59M4320_DG68-00882A-01_EN.indd 39 2/16/2017 3:45:33 PM
40 English
Maintaining your appliance
Maintaining your appliance
Removing and replacing the oven door
How to remove the door
CAUTION
The door is very heavy. Be careful when removing and lifting the door.
Do not lift the door by the handle.
Turn the power OFF before removing the door.
Hinge lock
Locked position Unlocked position
1. Open the door completely.
2. Pull the hinge locks down toward the door frame to the unlocked position.
about 5°
Fig. 1
3. Firmly grasp both sides of the door at
the top.
4. Close the door to the door removal
position, which is approximately
5 degrees from vertical (Fig. 1).
Fig. 2
5. Lift door up and out until the hinge
arm is clear of the slot (Fig. 2).
How to replace the door
Hinge arm
Bottom
edge of
slot
Indentation
1. Firmly grasp both sides of the door at the top.
2. With the door at the same angle as the removal position, slide the indentation
of the hinge arm into the bottom edge of the hinge slot. The notch in the
hinge arm must be fully inserted into the bottom of the slot.
NE59M4320_DG68-00882A-01_EN.indd 40 2/16/2017 3:45:34 PM
English 41
Maintaining your appliance
Hinge lock
Locked positionUnlocked position
3. Open the door fully. If the door will not open fully, the indentation is not
inserted correctly in the bottom edge of the slot.
4. Push the hinge locks up against the front frame of the oven cavity to the
locked position.
5. Close the oven door.
Removing and replacing the storage drawer
Hook
How to remove the storage drawer
1. Pull the drawer out until it stops.
2. Tilt the front of the drawer and pull out
it until it stops.
3. Lift and pull the drawer out.
How to replace the storage drawer
1. Put the left side of the drawer over the
left hook and the right side over the
right hook.
2. Push the drawer until it stops.
3. Tilt and lift the drawer.
4. Push the drawer in.
Changing the oven light
The oven light is a standard 40-watt appliance bulb. It will come on when the oven
door is open. When the oven door is closed, press the pad to turn it on or
off. It will not work during a self-cleaning cycle.
Bulb
Remove Replace
Glass bulb cover
1. Make sure the oven and the bulb are
cool.
2. Unplug the range or disconnect the
power.
3. Turn the glass bulb cover in the back of
the oven counterclockwise to remove.
4. Turn the bulb counterclockwise to
remove it from its socket.
5. Insert a new 40 watt appliance bulb,
and then turn it clockwise to tighten.
Replace the bulb cover by turning
clockwise.
6. Plug in the range or reconnect the
power.
CAUTION
Before changing your oven light bulb,
disconnect the electrical power to the range
at the main fuse or circuit breaker panel.
Make sure the oven and the bulb are cool.
NE59M4320_DG68-00882A-01_EN.indd 41 2/16/2017 3:45:35 PM
42 English
Troubleshooting
Troubleshooting
Troubleshooting
Samsung works hard to ensure that you don’t have problems with your new electric
range. If you run into unexpected trouble, look rst for a solution in the table below.
If, after trying the suggested solution, you’re still having trouble, call Samsung at
1-800-SAMSUNG (1-800-726-7864).
Installtion
Problem Possible cause Solution
The range is not
level.
The appliance has been
installed improperly.
Place the oven rack
in the center of the
oven. Place a level on
the oven rack. Adjust
the leveling legs at the
base of the range until
the oven rack is level.
Insure the oor is level
and strong and stable
enough to adequately
support the range.
The oor is sagging or
sloping.
Contact a carpenter to
correct the situation.
The kitchen cabinets are
not properly aligned and
make the range appear to
be not level.
Insure the cabinets are
square and provide
sufcient room for
installation.
The appliance
must be accessed
for servicing and
cannot be moved
easily.
The kitchen cabinets are
not square and too close to
the appliance.
Contact a builder or
installer to make the
appliance accessible.
Carpet is interfering with
movement of the range.
Provide sufcient space so
the range can be lifted over
the carpet.
CONTROL DISPLAY
Problem Possible cause Solution
The Display goes
blank.
A fuse in your home may be
blown or the circuit breaker
tripped.
Replace the fuse or reset the
circuit breaker.
The Display ashes. There was a power failure. Reset the clock.
COOKTOP
Problem Possible cause Solution
The surface units will
not maintain a rolling
boil or will not cook
fast enough.
You may be using
inappropriate cookware.
Use pans which are at and
match the diameter of the
surface unit selected.
In some areas, the power
(voltage) may be low.
Cover the pan with a lid until
the desired heat is obtained.
The surface units will
not turn on.
A fuse in your home may be
blown or the circuit breaker
tripped.
Replace the fuse or reset the
circuit breaker.
The cooktop controls are set
improperly.
Check if the correct control is
set for the surface unit you
are using.
Areas of discoloration
on the cooktop.
Food spillover was not
cleaned.
Refer to the section on the
care and cleaning of the
glass cooktop on pages
38-39.
The surface is hot and the
model features a light-
colored cooktop.
This is normal. The surface
may appear discolored when
it is hot. This is temporary
and will disappear as the
glass cools.
NE59M4320_DG68-00882A-01_EN.indd 42 2/16/2017 3:45:35 PM
English 43
Troubleshooting
Problem Possible cause Solution
The surface unit
frequently cycles on
and off.
The surface unit
stops glowing when
changed to a lower
setting.
The element will cycle on
and off to maintain the
power setting.
This is normal operation, and
not a system failure. Use the
oven as usual.
Scratches or
abrasions on the
cooktop surface.
The cooktop is being cleaned
improperly.
Scratches are not removable.
Tiny scratches will become
less visible in time as a result
of cleaning. Use ceramic
glass top cleaning cream. Do
not use chemical or corrosive
agents. These agents may
damage the surface of the
product.
Cookware with rough
bottoms was used on the
cooktop or there were
coarse particles (eg. salt or
sand) present between the
cookware and the surface of
the cooktop.
To avoid scratches, use the
recommended cleaning
procedures. Make sure
cookware bottoms are
clean before use, and use
cookware with smooth
bottoms.
Cookware has been slid
across the cooktop surface.
Problem Possible cause Solution
Brown streaks or
specks.
Boilovers have been cooked
onto the surface.
Wait until the surface
cools down. Then, use a
scraper to remove those
impurities. Use the
blade scraper to remove
soil.
See the section on the
care and cleaning of the
glass cooktop on pages
38-39.
Areas of discoloration
with metallic sheen.
Mineral deposits from water
and food have been left on
the surface of the cooktop.
Remove using a
ceramic-glass cooktop
cleaning cream.
Use cookware with
clean, dry bottoms.
Clean the cooktop with
a ceramic cleaning
agent regularly every
week.
“Cracking” or
“popping” sound.
This is the sound of the
metal heating and cooling
during both the cooking and
self-cleaning functions.
This is normal operation, and
not a system failure. Use the
oven as usual.
NE59M4320_DG68-00882A-01_EN.indd 43 2/16/2017 3:45:35 PM
44 English
Troubleshooting
Troubleshooting
OVEN
Problem Possible cause Solution
The oven will not
turn on.
The range is not completely
plugged into the electrical
outlet.
Make sure the electrical
plug is inserted into a live,
properly grounded outlet.
A fuse in your home may
be blown or the circuit
breaker tripped.
Replace the fuse or reset
the circuit breaker.
The oven controls have
been set improperly.
See the chapter on
operating the oven.
The oven is too hot. Allow the oven to cool.
Incomplete service wiring. Call for service.
Power outage. Check to see if the house
lights will turn on. If
required, call your local
electric company for
service.
The oven light will
not turn on.
The light bulb is loose or
defective.
Tighten or replace the bulb.
The switch operating the
light is broken.
Call for service.
Problem Possible cause Solution
Oven smokes
excessively during
broiling.
The control has not been
set properly.
Refer to the section on
setting oven controls.
The meat has been placed
too close to the element.
Reposition the rack to
provide proper clearance
between the meat and the
element. Preheat the broil
element for searing.
The meat has not been
properly prepared.
Remove the excess fat
from the meat. Cut away
fatty edges that may curl,
leaving the lean intact.
Grease has built up on oven
surfaces.
Regular cleaning is
necessary when broiling
frequently.
Food does not bake
or roast properly.
The oven controls have not
been set correctly.
See the chapter on
operating the oven.
The oven rack has been
positioned incorrectly or is
not level.
See the section on using
the oven racks on pages
25-26.
Incorrect cookware or
cookware of improper size
is being used.
The oven sensor needs to
be adjusted.
See the section on
adjusting the thermostat on
page 32.
NE59M4320_DG68-00882A-01_EN.indd 44 2/16/2017 3:45:35 PM
English 45
Troubleshooting
Problem Possible cause Solution
Food does not broil
properly.
The serving size may not
be appropriate.
Refer to the cooking guide
for serving sizes and try
again.
The rack has not been
properly positioned.
See the broiling
recommendation guide on
page 29.
Cookware not suited for
broiling.
Use suitable cookware.
In some areas, the power
(voltage) may be low.
Preheat the
broil element for
10 minutes.
See the broiling
recommendation guide
on page 29.
The oven
temperature is too
hot or too cold.
The oven sensor needs to
be adjusted.
See the section on
adjusting the thermostat on
page 32.
The oven will not
self-clean.
The oven temperature is
too high to start a self-
clean operation.
Allow the range to cool,
and then reset the controls.
The oven controls have
been set incorrectly.
See the section on self-
cleaning on page 34.
A self-cleaning cycle cannot
be started if the oven
lockout feature has been
activated or if a radiant
surface element is on.
Deactivate the oven
lockout (see page 33).
Make sure all surface
elements are turned off.
Problem Possible cause Solution
Excessive smoking
during a self-
cleaning cycle.
There is excessive soiling in
the oven.
Press OVEN OFF. Open the
windows to rid the room of
smoke. Wait until the self-
cleaning cycle is cancelled.
Wipe up the excessive soil,
and then start the self-
cleaning cycle again.
The oven door will
not open after a
self-cleaning cycle.
The oven is too hot. Allow the oven to cool.
The oven is not
clean after a self-
cleaning cycle.
The oven controls were not
set correctly.
See the section on self-
cleaning on page 34.
The oven was heavily
soiled.
Wipe up heavy spillovers
before starting the self-
cleaning cycle. Heavily
soiled ovens may need to
be self-cleaned again or for
a longer period of time.
Steam is coming out
of the vent.
When using the convection
feature, it is normal to see
steam coming out of the
oven vent.
This is normal operation,
and not a system failure.
Use the oven as usual.
As the number of racks
or amount of food being
cooked increases, the
amount of visible steam
will increase.
NE59M4320_DG68-00882A-01_EN.indd 45 2/16/2017 3:45:35 PM
46 English
Troubleshooting
Troubleshooting
Problem Possible cause Solution
A burning or oily
odor is coming from
the vent.
This is normal in a new
oven and will disappear in
time.
To speed the process,
set a self-cleaning
cycle for a minimum of
3 hours.
See the section on
self-cleaning on page
34.
Strong odor. An odor coming from the
insulation around the inside
of the oven is normal for
the rst few times the oven
is used.
Operate the oven at the
bake setting at 400 °F for
1 hour.
Fan noise. A convection fan may
automatically turn on and
off.
This is normal operation,
and not a system failure.
Use the oven as usual.
Oven racks are
difcult to slide.
The shiny, silver-colored
racks were cleaned in a
self-cleaning cycle.
Apply a small amount of
vegetable oil to a paper
towel and wipe the edges
of the oven racks with the
paper towel.
DRAWER
Problem Possible cause Solution
The Drawer does
not slide smoothly
or drags.
The drawer is out of
alignment.
Fully extend the drawer
and push it all the way in.
See the page 41.
The drawer is over-loaded
or the load is unbalanced.
Reduce weight. Redistribute
drawer contents.
Information codes
OVEN
Problem Possible cause Solution
C-20 The oven sensor is open
when the oven is operating.
Press OVEN OFF and restart
the oven. If the problem
persists, disconnect all
power to the range for at
least 30 seconds and then
reconnect the power. If this
does not solve the problem,
call for service.
The oven sensor is short
when the oven is operating.
C-21 This code occurs if the
internal temperature rises
abnormally high.
C-d1 This code occurs if the door
lock is mispositioned.
C-d0 This code occurs if the
Control key is short for
1 minute.
Press OVEN OFF and restart
the oven. If the problem
persists, disconnect all
power to the range for at
least 30 seconds and then
reconnect the power. If this
does not solve the problem,
call for service.
C-30 The PCB sensor is open
when the oven is operating.
The PCB sensor is short
when the oven is operating.
C-31 This code occurs if the
PCB temperature rises
abnormally high.
Call for service.
NE59M4320_DG68-00882A-01_EN.indd 46 2/16/2017 3:45:35 PM
English 47
Warranty (U.S.A)
Warranty (U.S.A)
PLEASE DO NOT DISCARD. THIS PAGE REPLACES THE WARRANTY PAGE IN THE
USE & CARE GUIDE
SAMSUNG ELECTRIC RANGE
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG
ELECTRONICS AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to
the original consumer purchaser, is warranted by SAMSUNG against manufacturing
defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor, One (1) Year Parts Warranty
For Glass Cooktop and Radiant Heater
This limited warranty begins on the original date of purchase, and is valid only
on products purchased and used in the United States. To receive warranty service,
the purchaser must contact SAMSUNG for problem determination and service
procedures. Warranty service can only be performed by a SAMSUNG authorized
service center. The original dated bill of sale must be presented upon request as
proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. Samsung
will provide in-home service during the warranty period at no charge subject to
availability within the contiguous United States. In home service is not available in
all areas. To receive in home service product must be unobstructed and accessible
to the service agent. If service is not available Samsung may elect to provide
transportation of the product to and from an authorized service center. SAMSUNG
will repair or replace this product, at our option and at no charge as stipulated
herein, with new or reconditioned parts or products if found to be defective
during the limited warranty period specied above. All replaced parts and
products become the property of SAMSUNG and must be returned to SAMSUNG.
Replacement parts and products assume the remaining original warranty, or ninety
(90) days, whichever is longer.
This limited warranty covers manufacturing defects in materials and workmanship
encountered in normal, noncommercial use of this product and shall not apply
to the following: damage which occurs in shipment; delivery and installation;
applications and uses for which this product was not intended; altered product
or serial numbers; cosmetic damage or exterior nish; accidents, abuse, neglect,
re, water, lightning or other acts of nature; use of products, equipment, systems,
utilities, services, parts, supplies, accessories, applications, installations, repairs,
external wiring or connectors not supplied or authorized by SAMSUNG which
damage this product or result in service problems; incorrect electrical line voltage,
uctuations and surges; customer adjustments and failure to follow operating
instructions, maintenance and environmental instructions that are covered and
prescribed in the instruction book; product removal and reinstallation; problems
caused by pest infestations, and overheating or overcooking by user. This limited
warranty shall not cover cases of incorrect electric current, voltage or supply, light
bulbs, house fuses, house wiring, cost of a service call for instructions, or xing
installation errors. Furthermore, damage to the glass cooktop caused by the use
of cleaners other than the recommended cleaners and pads, damage to the glass
cook top caused by hardened spills of sugary materials or melted plastic that are
not cleaned according to the directions in the use and care guide are not covered.
SAMSUNG does not warrant uninterrupted or error-free operation of the product.
NE59M4320_DG68-00882A-01_EN.indd 47 2/16/2017 3:45:35 PM
48 English
Warranty (CANADA)
EXCEPT AS SET FORTH HEREIN THERE ARE NO WARRANTIES ON THIS
PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL
NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS
OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT,
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN
IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR
SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT
THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING
THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER
ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING
OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some provinces or territories may or may not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specic legal rights, and you may also have other rights which
vary from state to state. User Replaceable Parts may be sent to the customer for
unit repair. If necessary, a Service Engineer can be dispatched to perform service.
To obtain warranty service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
85 Challenger Road Ridgeeld Park, NJ 07660
1-800-SAMSUNG (726-7864) and www.samsung.com/us/support
Warranty (CANADA)
PLEASE DO NOT DISCARD. THIS PAGE REPLACES THE WARRANTY PAGE IN THE
USE & CARE GUIDE
SAMSUNG ELECTRIC RANGE
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG
ELECTRONICS CANADA, INC. (SAMSUNG) and delivered new, in the original carton to
the original consumer purchaser, is warranted by SAMSUNG against manufacturing
defects in materials and workmanship for a limited warranty period of:
One (1) Year Parts and Labor, One (1) Year Parts Warranty
For Glass Cooktop and Radiant Heater
This limited warranty begins on the original date of purchase, and is valid only
on products purchased and used in the CANADA. To receive warranty service,
the purchaser must contact SAMSUNG for problem determination and service
procedures. Warranty service can only be performed by a SAMSUNG authorized
service center. The original dated bill of sale must be presented upon request as
proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. Samsung
will provide in-home service during the warranty period at no charge subject to
availability within the contiguous CANADA. In home service is not available in all
areas. To receive in home service product must be unobstructed and accessible
to the service agent. If service is not available Samsung may elect to provide
transportation of the product to and from an authorized service center.
NE59M4320_DG68-00882A-01_EN.indd 48 2/16/2017 3:45:36 PM
English 49
Warranty (CANADA)
SAMSUNG will repair or replace this product, at our option and at no charge
as stipulated herein, with new or reconditioned parts or products if found to
be defective during the limited warranty period specied above. All replaced
parts and products become the property of SAMSUNG and must be returned
to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer. This limited warranty covers
manufacturing defects in materials and workmanship encountered in normal,
noncommercial use of this product and shall not apply to the following: damage
which occurs in shipment; delivery and installation; applications and uses for
which this product was not intended; altered product or serial numbers; cosmetic
damage or exterior nish; accidents, abuse, neglect, re, water, lightning or
other acts of nature; use of products, equipment, systems, utilities, services,
parts, supplies, accessories, applications, installations, repairs, external wiring or
connectors not supplied or authorized by SAMSUNG which damage this product or
result in service problems; incorrect electrical line voltage, uctuations and surges;
customer adjustments and failure to follow operating instructions, maintenance
and environmental instructions that are covered and prescribed in the instruction
book; product removal and reinstallation; problems caused by pest infestations,
and overheating or overcooking by user. This limited warranty shall not cover
cases of incorrect electric current, voltage or supply, light bulbs, house fuses,
house wiring, cost of a service call for instructions, or xing installation errors.
Furthermore, damage to the glass cooktop caused by the use of cleaners other
than the recommended cleaners and pads, damage to the glass cook top caused
by hardened spills of sugary materials or melted plastic that are not cleaned
according to the directions in the use and care guide are not covered. SAMSUNG
does not warrant uninterrupted or error-free operation of the product.
EXCEPT AS SET FORTH HEREIN THERE ARE NO WARRANTIES ON THIS
PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL
NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS
OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT,
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN
IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR
SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT
THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING
THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER
ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING
OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specic
legal rights, and you may also have other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
Samsung Electronics Canada Inc.
2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada
1-800-SAMSUNG (726-7864) and www.samsung.com/ca/support (English)
www.samsung.com/ca_fr/support (French)
NE59M4320_DG68-00882A-01_EN.indd 49 2/16/2017 3:45:36 PM
Memo
NE59M4320_DG68-00882A-01_EN.indd 50 2/16/2017 3:45:36 PM
Memo
NE59M4320_DG68-00882A-01_EN.indd 51 2/16/2017 3:45:36 PM
Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or
maintenance.
QUESTIONS OR COMMENTS?
COUNTRY CALL OR VISIT US ONLINE AT
U.S.A
Consumer Electronics
1-800-SAMSUNG (726-7864) www.samsung.com/us/support
CANADA 1-800-SAMSUNG (726-7864)
www.samsung.com/ca/support (English)
www.samsung.com/ca_fr/support (French)
DG68-00882A-01
Scan the QR code* or visit
www.samsung.com/spsn
to view our helpful
How-to Videos and Live Shows
* Requires reader to be installed on
your smartphone
NE59M4320_DG68-00882A-01_EN.indd 52 2/16/2017 3:45:36 PM
Estufa eléctrica
Manual del usuario
NE59M4320**
NE59M4320_DG68-00882A-01_MES.indd 1 2/16/2017 3:45:48 PM
2 Español
Notas
Dispositivo anti inclinación
ADVERTENCIA
Para reducir el riesgo de inclinación o vuelco de la estufa, ésta debe estar
asegurada mediante un Dispositivo Anti Inclinación correctamente instalado.
DESPUÉS DE INSTALAR LA ESTUFA, CONFIRME QUE EL DISPOSITIVO ANTI
INCLINACIÓN ESTÉ CORRECTAMENTE INSTALADO Y VERIFIQUE QUE ESTÉ
CORRECTAMENTE CONECTADO. Consulte el manual de instalación donde se
brindan las instrucciones correspondientes.
a) Si el dispositivo anti inclinación no está instalado, un niño o un
adulto podrían inclinar la estufa y morir.
b) Verique que el dispositivo anti inclinación haya sido instalado
y conectado correctamente en la parte posterior derecha
(o posterior izquierda) de la base de la estufa.
c) Si mueve la estufa y luego la vuelve a colocar en su lugar,
asegúrese de volver a conectar el dispositivo anti inclinación
en la parte posterior derecha o izquierda de la base de la
estufa.
d) No opere la estufa sin el dispositivo anti inclinación en su lugar
y conectado.
e) No hacerlo puede provocar la muerte o quemaduras serias a
niños o adultos.
ADVERTENCIA
No se pare sobre las puertas de la estufa, ni se apoye o siente sobre
ellas. Puede causar que la estufa se incline o vuelque, produciendo
quemaduras o lesiones severas.
Conrme que el dispositivo anti inclinación se encuentre instalado
correctamente. Luego, para vericar que dicho dispositivo
esté conectado, tome el borde superior trasero de la estufa y
cuidadosamente intente inclinarla hacia adelante. El dispositivo anti
inclinación debería prevenir que la estufa se incline hacia adelante
más de unas pocas pulgadas.
Si, por cualquier razón, hala la estufa alejándola de la pared,
asegúrese de que el dispositivo anti inclinación encaje correctamente
cuando empuje la estufa a su lugar contra la pared. Si no se encuentra
encajado, hay riesgo de que la estufa se incline o vuelque y cause
lesiones si usted o un niño se parasen, sentasen o apoyasen sobre la
puerta abierta.
Nunca retire completamente las patas niveladoras. Si las retira, la
estufa no quedará sujeta correctamente al dispositivo anti inclinación.
NE59M4320_DG68-00882A-01_MES.indd 2 2/16/2017 3:45:48 PM
Español 3
Contenido
Contenido
Instrucciones de seguridad importantes 4
Introducción a su nueva estufa 16
Descripción general 16
Elementos incluidos con su estufa 16
Antes de comenzar 17
Sugerencias para ahorrar energía 17
Cocción en cubierta 17
Acerca de la cocción en cubierta 17
Como regular su estufa para la cocción de cubierta 19
Utilización de los recipientes de cocción correctos 20
Selección de los recipientes de cocción correctos 21
Protección de la cubierta 21
Funcionamiento del horno 22
Panel de control del horno 22
Ajuste del reloj 23
Cómo programar el temporizador de cocina 23
Cocción por temporizador 24
Inicio retardado 24
Cómo encender y apagar la luz del horno 25
Ajustes mínimos y máximos 25
Uso de las parrillas del horno 25
Hornear 26
Hornear por convección 27
Asar por convección 28
Asar a la parrilla 28
Cómo utilizar la función de cocción fácil 29
Cómo usar la función de mantener temperatura 30
Uso de la función Shabat 31
Funciones adicionales 32
Mantenimiento de su electrodoméstico 34
Auto-limpieza 34
Limpieza con vapor 36
Cuidado y limpieza del horno 36
Cuidado y limpieza de la cubierta de vidrio 38
Cómo retirar y volver a colocar la puerta del horno 40
Cómo retirar y volver a colocar el cajón de almacenamiento 41
Recambio de la luz del horno 41
Resolución de problemas 42
Resolución de problemas 42
Códigos de información 46
Garantía (EE.UU.) 47
Garantía (CANADÁ) 48
NE59M4320_DG68-00882A-01_MES.indd 3 2/16/2017 3:45:48 PM
4 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
Lea y siga todas las instrucciones antes de utilizar su horno con el n de
evitar riesgos de incendio, descargas eléctricas, lesiones personales o daños
al utilizar su estufa. Esta guía no cubre todas las situaciones que podrían
ocurrir. Siempre tome contacto con su agente de servicio o con el fabricante
para consultar sobre cualquier problema que usted no comprenda.
LO QUE NECESITA SABER SOBRE LAS
INSTRUCCIONES DE SEGURIDAD
Las advertencias y las instrucciones de seguridad importantes de este
manual no cubren todos los problemas y situaciones que podrían ocurrir.
Usted tiene la responsabilidad de usar el sentido común, de ser precavido y
cuidadoso al instalar, mantener y manejar su horno.
Símbolos y precauciones de seguridad
importantes
Signicado de iconos y símbolos en este manual del usuario:
ADVERTENCIA
Prácticas peligrosas o inseguras que pueden provocar lesiones personales
graves o la muerte.
PRECAUCIÓN
Prácticas peligrosas o inseguras que pueden provocar lesiones personales
leves o daños a la propiedad.
PRECAUCIÓN
Para reducir el riesgo de incendio, explosión, descarga eléctrica o lesiones
personales cuando utilice el horno, siga estas instrucciones básicas de seguridad.
NO intentar.
NO desensamblar.
NO tocar.
Siga las instrucciones explícitamente.
Desenchufe la alimentación eléctrica del tomacorriente de la pared.
Asegúrese de que la máquina tenga buena conexión a tierra para
evitar descargas eléctricas.
Comuníquese con el centro de servicio técnico para obtener ayuda.
Nota
Estas señales de advertencia se incluyen para evitar lesiones a usted y a
otras personas. Sígalas explícitamente.
Una vez que haya leído esta sección, consérvela en un lugar seguro para
consultas futuras.
ADVERTENCIA SOBRE LA STATE OF
CALIFORNIA PROPOSITION 65 SOLO EE.UU.
ADVERTENCIA: Este producto contiene productos químicos
reconocidos en el estado de California como capaces de provocar
cáncer y defectos de nacimiento u otras afecciones reproductivas.
NE59M4320_DG68-00882A-01_MES.indd 4 2/16/2017 3:45:49 PM
Español 5
Instrucciones de seguridad importantes
PARA SU SEGURIDAD
Cuando utilice electrodomésticos, debe seguir unas precauciones de
seguridad básicas, a saber:
PRECAUCIÓN
Utilice este electrodoméstico solo para el uso para el que fue destinado, tal
como se describe en este Manual del propietario.
Las supercies que podrían estar calientes incluyen la cubierta, áreas
enfrente de la cubierta, abertura de ventilación del horno, supercies
cercanas a dicha abertura y las hendeduras alrededor de la puerta del horno.
Asegúrese de que su electrodoméstico sea correctamente instalado y
conectado a tierra por un técnico calicado.
Mantenimiento del usuario- No repare ni reemplace ninguna pieza de
este electrodoméstico salvo que esto se encuentre especícamente
recomendado en este manual. Todas las demás tareas de reparación o
mantenimiento deben ser encomendadas a un técnico calicado.
Antes de realizar tareas de mantenimiento o reparación, siempre
desconecte la alimentación eléctrica al electrodoméstico quitando el fusible
o accionando el disyuntor.
No se introduzca en el horno.
Ningún artículo que pueda resultar de interés para los niños debe
almacenarse en gabinetes arriba de una estufa o en su anaquel
posterior. Los niños que se trepasen a la estufa para alcanzar los
elementos podrían resultar seriamente lesionados.
No deje solos a los niños. Los niños nunca deben quedar solos o sin
vigilancia en el lugar donde se utiliza este electrodoméstico. Nunca
se les debe permitir sentarse o pararse sobre ninguna parte del
electrodoméstico.
Nunca utilice su electrodoméstico para entibiar o calentar el ambiente.
No eche agua sobre grasas en llamas. Apague el horno para evitar
que las llamas se extiendan. Ahogue el fuego o las llamas cerrando la
puerta, o bien utilice un producto químico seco, bicarbonato de sosa o
un extintor de incendio a base de espuma.
Evite rayar o impactar las puertas de vidrio, cubiertas o paneles de
control. Hacerlo puede producir la rotura del vidrio. No cocine sobre un
producto con vidrios rotos. Se pueden producir descargas eléctricas, un
incendio o cortes.
Si se produce un incendio en el horno durante la auto-limpieza, apague
el horno y espere a que se extinga el fuego. No fuerce la apertura de la
puerta. La entrada de aire fresco a las temperaturas de auto-limpieza
puede avivar las llamas en el horno. No cumplir con esta instrucción
puede dar como resultado quemaduras graves.
Si el horno está muy sucio de aceite, haga auto-limpieza del mismo
antes de usarlo nuevamente. Dejar el aceite crea un riesgo de incendio.
Friegue la suciedad resistente de la parte baja del horno con un trapo
o una toalla de papel antes de la auto limpieza Hacer auto limpieza
del horno cuando hay aceite pesado en el interior requiere ciclos de
limpieza más largos y produce más humo.
NE59M4320_DG68-00882A-01_MES.indd 5 2/16/2017 3:45:49 PM
6 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
Almacenamiento en o sobre el electrodoméstico. No almacene
materiales inamables en el horno o cerca de las unidades de supercie.
Asegúrese de que todos los materiales de empaque hayan sido retirados
del electrodoméstico antes de ponerlo en funcionamiento. Mantenga
materiales plásticos, indumentaria y papeles alejados de las partes del
electrodoméstico que podrían calentarse.
Utilice la indumentaria apropiada. Nunca use prendas amplias o
colgantes mientras utiliza el electrodoméstico.
Utilice solamente agarradores aislantes secos. Colocar agarradores
aislantes mojados o húmedos sobre supercies calientes podría
producir quemaduras por vapor. No permita que el agarrador entre en
contacto con los elementos calentadores cuando están calientes.
No utilice una toalla o cualquier otra tela voluminosa.
Enseñe a los niños que no deben jugar con los controles ni con ninguna
otra parte de la estufa.
Por seguridad, no use limpiadores de agua a alta presión ni limpiadores
a chorro de vapor.
Si el cable de alimentación está dañado, deberá ser reemplazado por el
fabricante, su agente de servicio técnico o personas con una calicación
similar a n de evitar riesgos.
El uso de este electrodoméstico no es apto para personas (incluye niños)
con capacidades físicas, sensoriales o mentales reducidas, o que no
tengan experiencia y conocimientos, a menos que sean supervisados o
hayan recibido instrucción sobre el uso del electrodoméstico por parte
de una persona responsable de su seguridad.
UNIDADES DE SUPERFICIE DE COCCIÓN
Nunca deje sin atención unidades de supercie reguladas a altas
temperaturas. Los derrames por exceso de hervor producen humo y
los derrames de sustancias grasas pueden arder en llamas.
Revestimientos protectores – No utilice papel de aluminio para
revestir los boles recogegotas o el fondo del horno, salvo de la
manera sugerida en el manual. La instalación incorrecta de estos
revestimientos puede causar riesgos de descarga eléctrica o
incendio.
Para evitar derrame de aceite o incendio, use una cantidad mínima
de aceite cuando haga frituras y evite cocinar alimentos congelados
con cantidades excesivas de hielo.
No levante la cubierta. Levantar la cubierta puede dañar la estufa y
generar un funcionamiento defectuoso.
No haga funcionar la cubierta sin utensilios de cocina. Si se hace
funcionar la cubierta sin un recipiente de cocción, se calentarán las
perillas de control.
Nunca utilice la supercie de vidrio de la cubierta como tabla para
cortar.
NE59M4320_DG68-00882A-01_MES.indd 6 2/16/2017 3:45:49 PM
Español 7
Instrucciones de seguridad importantes
Sea precavido al tocar la cubierta. La supercie de vidrio de la
cubierta retendrá el calor aún después de que se hayan apagado los
controles.
Tenga cuidado cuando coloque cucharas u otros utensilios para
revolver sobre la supercie de vidrio de la cubierta mientras se
encuentre en uso. Podrían calentarse y causar quemaduras.
Utilice recipientes de cocción del tamaño adecuado. Este
electrodoméstico se encuentra equipado con unidades de supercie
de diferentes tamaños. Seleccione ollas y sartenes que tengan bases
planas lo sucientemente grandes para cubrir la supercie del
elemento calentador. Si se utilizan recipientes demasiado pequeños,
una porción del elemento calentador quedará expuesta al contacto
directo y podría causar que sus ropas ardieran. Hacer coincidir el
tamaño de la olla o sartén con el quemador también mejorará la
eciencia.
Las manijas de los utensilios deben estar posicionadas hacia
adentro y sin proyectarse sobre unidades de supercie adyacentes
– Para reducir el riesgo de quemaduras, encendido de materiales
inamables o derrames causados por contactos accidentales con los
utensilios, posicione las manijas de los mismos hacia adentro y sin
proyectarse sobre unidades de supercie adyacentes.
Utensilios de cocción vidriados, enlozados o esmaltados. Solamente
ciertos tipos de utensilios de vidrio, vidrio/cerámica o cerámica, o
con supercies esmaltadas o con otros tratamientos pueden usarse
en la supercie de cocción sin romperse por bruscas diferencias de
temperatura.
Limpieza. Lea y siga todas las instrucciones y advertencias de las
etiquetas de las cremas de limpieza.
Asegúrese de saber cuál de las perillas controla cada unidad de
supercie. Asegúrese de que encendió la unidad de supercie
correcta.
Siempre apague las unidades de supercie antes de retirar los
recipientes de cocción.
Cuando prepare platillos ambeados debajo de la campana, encienda
el ventilador.
Vigile las frituras que se realicen con regulaciones de temperatura
altas o medianas.
No almacene objetos pesados sobre la supercie de la cubierta que
pudieran caerse y dañarla.
No use cubiertas decorativas para elementos de supercie – Si se
enciende accidentalmente un elemento, la cubierta decorativa se
calentará y posiblemente derretirá. Se producirán quemaduras si se
tocan las cubiertas calientes. También se puede dañar la cubierta.
NE59M4320_DG68-00882A-01_MES.indd 7 2/16/2017 3:45:49 PM
8 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
SEGURIDAD ELÉCTRICA
Instalación adecuada - Asegúrese de que su electrodoméstico sea
correctamente instalado y conectado a tierra por un técnico calicado.
El electrodoméstico debe ser reparado únicamente por personal
técnico calicado. Las reparaciones realizadas por personas no
calicadas pueden causar lesiones o fallas graves. Si necesita reparar
su electrodoméstico, comuníquese con un centro de servicio autorizado
de Samsung. No seguir estas instrucciones puede resultar en daños y
anular la garantía.
Los electrodomésticos montados a nivel pueden operarse solo después
de que fueron instalados en gabinetes y lugares de trabajo que cumplen
con las normas pertinentes. Esto asegura que los electrodomésticos
sean instalados cumpliendo con las normas de seguridad adecuadas.
Si su electrodoméstico funciona mal o si aparecen roturas, rajaduras o
grietas:
- apague todas las zonas de cocción
- desenchufe la estufa del tomacorriente CA de la pared
- comuníquese con su centro de servicio local de Samsung.
ADVERTENCIA
Si la supercie está rajada, apague y desenchufe el electrodoméstico para
evitar la posibilidad de una descarga eléctrica. No utilice su cubierta hasta
que la supercie de vidrio haya sido reemplazada.
ADVERTENCIA
Asegúrese de que el electrodoméstico esté apagado antes de reemplazar
la bombilla de luz para evitar la posibilidad de una descarga eléctrica.
La estufa no debe colocarse sobre una base.
SEGURIDAD DE LOS NIÑOS
ADVERTENCIA
Este electrodoméstico no está previsto para ser utilizado por niños o
personas enfermas sin la adecuada supervisión de un adulto responsable.
Los niños deben ser supervisados para garantizar que no jueguen con el
electrodoméstico.
Mantenga a los niños alejados de la puerta cuando la abra o la
cierre ya que podría golpearlos o pillarles los dedos.
Las zonas de cocción se calentarán cuando usted cocine. Para evitar
que los niños pequeños se quemen, siempre manténgalos alejados del
electrodoméstico cuando cocina.
Durante la auto-limpieza, las supercies pueden calentarse más que lo
normal. Mantenga los niños pequeños alejados de la estufa cuando es
en el modo de auto-limpieza
ADVERTENCIA
Las partes accesibles pueden calentarse durante el uso. Los niños pequeños
deben mantenerse alejados para evitar quemaduras.
NE59M4320_DG68-00882A-01_MES.indd 8 2/16/2017 3:45:50 PM
Español 9
Instrucciones de seguridad importantes
HORNO
NO TOQUE LOS ELEMENTOS CALENTADORES NI LAS SUPERFICIES
INTERIORES DEL HORNO. Los elementos calentadores pueden estar
calientes aun cuando su color sea oscuro. Las supercies interiores de
un horno se calientan lo suciente como para producir quemaduras.
Durante y después del uso, no toque los elementos calentadores ni las
supercies interiores del horno y tampoco permita que sus ropas ni
otros materiales inamables entren en contacto con ellos hasta que haya
transcurrido tiempo suciente como para que se enfríen. Otras supercies
del electrodoméstico pueden calentarse lo suciente como para producir
quemaduras. Entre ellas se encuentran las aberturas de ventilación del
horno y supercies cercanas a estas aberturas, la puerta del horno y la
ventana de la puerta del horno.
No caliente envases de alimentos que no hayan sido abiertos.
La acumulación de presión puede hacer que el envase explote y cause
lesiones.
No utilice el horno para secar periódicos. Si se recalientan, pueden arder en
llamas.
No utilice el horno para almacenar objetos ni alimentos. Los elementos
almacenados en un horno pueden arder.
Cuando abra la puerta, hágalo con precaución. Permita la salida del vapor o
aire caliente antes de retirar o volver a colocar los alimentos en el horno.
Revestimientos protectores. No utilice papel de aluminio para revestir el
fondo del horno, salvo de la manera sugerida en el manual. La instalación
incorrecta de estos revestimientos puede causar riesgos de descarga
eléctrica o incendio.
Mantenga los conductos de ventilación del horno libres de obstrucciones.
La abertura de ventilación se encuentra ubicada por sobre la unidad de
supercie trasera derecha. Esta área podría calentarse durante el uso del
horno. Nunca tapone esta abertura de ventilación ni coloque elementos de
plástico o sensibles al calor sobre dicha abertura.
Colocación de las parrillas del horno. Siempre coloque las parrillas del
horno en la posición deseada mientras el horno esté frío. Si debe moverse
la parrilla cuando el horno está caliente, use agarradores aislantes.
No deje que los agarradores aislantes entren en contacto con el elemento
calentador caliente en el horno.
No permita que papel de aluminio o una sonda para carne entren en
contacto con los elementos calentadores.
Durante el uso, el electrodoméstico se calienta. Se debe tener la precaución
de evitar tocar los elementos calentadores del interior del horno.
No utilice limpiadores abrasivos ni espátulas de metal losas para limpiar
el vidrio de la puerta del horno. Podrían rayar la supercie, lo cual puede
provocar que el vidrio se haga añicos.
PRECAUCIÓN
No intente hacer funcionar el horno durante un corte de energía eléctrica.
Si se produce un corte de energía, siempre apague el horno. Si no se apaga
el horno y se restablece el suministro de energía, el horno puede empezar
a funcionar nuevamente. Los alimentos que quedaron desatendidos podrían
arder en llamas o arruinarse.
NE59M4320_DG68-00882A-01_MES.indd 9 2/16/2017 3:45:50 PM
10 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
HORNOS AUTOLIMPIANTES
No limpie la junta selladora de la puerta. La junta de la puerta es esencial
para lograr que el horno quede bien sellado. Se debe tener cuidado de no
frotar, dañar o mover la junta.
Nunca tenga aves mascota en la cocina. Las aves son extremadamente
sensibles a las emanaciones gaseosas que se producen durante el
ciclo de auto-limpieza del horno. Tales emanaciones pueden resultar
dañinas o mortales para las aves. Lleve las aves a una habitación bien
ventilada.
Aplique el ciclo de auto-limpieza únicamente a las piezas enumeradas
en este manual. Antes de la auto-limpieza del horno, quite la partición,
la parrilla, los utensilios y los alimentos.
Antes de hacer funcionar el ciclo de auto-limpieza, limpie la grasa y
los restos de comida del horno. Unas cantidades excesivas de grasa
podrían encenderse y generar daños por el humo en su hogar.
No use ningún producto limpiador de hornos ni revestimiento
protector dentro del horno ni sobre sus supercies exteriores.
Retire los estantes niquelados del horno antes de comenzar el ciclo de
auto-limpieza, de lo contrario pueden sufrir alteraciones de color.
Si el ciclo de auto-limpieza funciona mal, apague el horno y desconecte
la alimentación eléctrica. Hágalo reparar por un técnico calicado.
Los derrames excesivos deben eliminarse antes de ejecutar el ciclo de
auto-limpieza.
CAMPANAS DE VENTILACIÓN
Limpie con frecuencia las campanas de ventilación. No deje que se
acumule grasa en la campana o el ltro.
Cuando ambee alimentos debajo de la campana, encienda el
ventilador.
SUPERFICIES DE COCCIÓN VITROCERÁMICAS
NO TOQUE LAS UNIDADES DE SUPERFICIE NI LAS ÁREAS CERCANAS
A LAS UNIDADES. Las unidades de supercie pueden estar calientes
aun cuando su color sea oscuro. Las áreas cercanas a las unidades
de supercie pueden calentarse lo suciente como para producir
quemaduras. Durante y después del uso, no toque las unidades de
supercie ni las áreas cercanas ni tampoco permita que sus ropas ni
otros materiales inamables entren en contacto con ellas hasta que
haya transcurrido tiempo suciente como para que se enfríen. Entre
estas áreas se cuentan la cubierta y su revestimiento.
No cocine sobre una cubierta quebrada. Si la cubierta se quebrase,
las soluciones de limpieza y sustancias derramadas podrían penetrar
la cubierta quebrada y generar riesgos de descarga eléctrica.
Comuníquese inmediatamente con un técnico calicado.
Limpie la cubierta con precaución. Si utiliza una esponja o un paño
húmedo para limpiar derrames en una supercie de cocción caliente,
cuídese de posibles quemaduras por vapor. Algunos productos de
limpieza pueden producir emanaciones nocivas si se aplican sobre una
supercie caliente.
NE59M4320_DG68-00882A-01_MES.indd 10 2/16/2017 3:45:50 PM
Español 11
Instrucciones de seguridad importantes
ADVERTENCIAS FUNDAMENTALES
PARA LA INSTALACIÓN
ADVERTENCIA
La instalación de este electrodoméstico debe estar a cargo de un
técnico o una compañía de servicio calicados.
- Si la estufa no es instalada por un técnico calicado, pueden
producirse descargas eléctricas, incendios, explosiones, problemas
con el producto o lesiones.
Desempaque el horno, retire todo el material de empaque y examine
el horno para determinar si hay daños tales como abolladuras en
el interior o exterior del electrodoméstico, pestillos de la puerta
rotos, rajaduras en la puerta o una puerta que no esté correctamente
alineada. Si hay algún daño, no ponga el horno en funcionamiento y
notique de inmediato al distribuidor.
Enchufe el cable de alimentación en un tomacorriente conectado
a tierra con la conguración adecuada. Su horno debe ser el único
elemento conectado en este circuito.
Mantenga todos los materiales de empaque fuera del alcance de los
niños. Podrían utilizarlos para jugar y lastimarse.
Instale el electrodoméstico en un piso nivelado y resistente que
pueda soportar el peso.
- De no hacerlo así, se pueden producir vibraciones anormales,
ruidos o problemas con el producto.
Este electrodoméstico debe conectarse a tierra correctamente.
No conecte el electrodoméstico a una tubería de gas, una tubería
plástica de agua o un cable de teléfono.
- Esto puede provocar descarga eléctrica, incendio, explosión o
problemas con el producto.
No corte ni retire el pin de conexión a tierra del cable de
alimentación bajo ninguna circunstancia.
Conecte el horno a un circuito que proporcione el amperaje correcto.
No instale este electrodoméstico en un lugar húmedo, engrasado o
cubierto de polvo, ni en un lugar expuesto a la luz solar directa o al
agua (gotas de lluvia).
- Se puede producir una descarga eléctrica o un incendio.
No utilice un cable de alimentación dañado ni un tomacorriente de
pared ojo.
- Se puede producir una descarga eléctrica o un incendio.
No jale ni doble excesivamente el cable de alimentación.
No retuerza ni ate el cable de alimentación.
No enganche el cable de alimentación de un objeto metálico, ni
coloque un objeto pesado sobre el cable de alimentación, ni inserte
el cable de alimentación entre objetos.
- Se puede producir una descarga eléctrica o un incendio.
Si se daña el cable de alimentación, comuníquese con el centro de
servicio técnico Samsung más cercano.
NE59M4320_DG68-00882A-01_MES.indd 11 2/16/2017 3:45:50 PM
12 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
ADVERTENCIA FUNDAMENTAL PARA
EL USO
PRECAUCIÓN
Si el electrodoméstico se inunda con cualquier líquido, comuníquese
con el centro de servicios más cercano. No hacerlo puede provocar
descarga eléctrica o incendio.
Si el electrodoméstico produce un ruido extraño, olor a quemado o
humo, desenchufe de inmediato la alimentación y comuníquese con
el centro de servicio técnico más cercano.
- No hacerlo puede provocar descarga eléctrica o incendio
En caso de producirse una fuga de gas (como gas propano, gas LP,
etc.), ventile el área de inmediato. No toque el cable de alimentación.
No toque el electrodoméstico.
- Una chispa puede causar una explosión o un incendio.
Tenga cuidado de no entrar en contacto con la puerta del horno, los
elementos calentadores o cualquier otra pieza caliente con su cuerpo
mientras cocina o justo después de cocinar.
- No hacerlo puede provocar quemaduras.
Si los materiales en el interior del horno se encendieran, mantenga
la puerta cerrada, apague el horno y desconecte el cable de
alimentación o corte la alimentación en el panel del disyuntor o
fusible. Si abre la puerta, el fuego puede expandirse.
Siempre respete las precauciones de seguridad cuando utilice su
horno. Nunca intente reparar el horno: contiene voltaje peligroso en
el interior. Si se debe reparar el horno, comuníquese con un centro
de servicio técnico autorizado cercano.
Si utiliza el electrodoméstico cuando está contaminado por
sustancias extrañas como, por ejemplo, restos de comida, pueden
surgir problemas.
Tenga cuidado al quitar el envoltorio cuando retira comida del
electrodoméstico.
- Si la comida está caliente, puede salir vapor caliente cuando retira
el envoltorio y esto puede provocar quemaduras.
No intente reparar, desarmar ni modicar el electrodoméstico.
- Como ingresa corriente de alta tensión en el chasis del producto,
esto puede provocar descarga eléctrica o incendio.
- Cuando sea necesaria una reparación, comuníquese con el centro
de servicio técnico más cercano.
Si alguna sustancia extraña como, por ejemplo, agua ingresa en el
electrodoméstico, comuníquese con el centro de servicio técnico más
cercano.
- No hacerlo puede provocar descarga eléctrica o incendio.
No toque el cable de alimentación con las manos húmedas.
- Se puede producir una descarga eléctrica.
No apague el electrodoméstico cuando hay una operación en
progreso.
- Esto puede provocar chispas y causar una descarga eléctrica o
incendio.
NE59M4320_DG68-00882A-01_MES.indd 12 2/16/2017 3:45:50 PM
Español 13
Instrucciones de seguridad importantes
Mantenga todos los materiales de empaque fuera del alcance de los
niños, ya que pueden ser peligrosos para ellos.
- Si un niño se coloca una bolsa de plástico en la cabeza, puede
asxiarse.
No deje que los niños ni ninguna persona con capacidades físicas,
sensoriales o mentales reducidas utilice el electrodoméstico sin
supervisión.
Asegúrese de que los controles del electrodoméstico y las áreas de
cocción estén fuera del alcance de los niños.
- No hacerlo puede provocar una descarga eléctrica, quemaduras o
lesiones.
No toque el interior del electrodoméstico inmediatamente después
de cocinar. El interior del electrodoméstico estará caliente.
- No hacerlo puede provocar quemaduras.
No utilice ni coloque objetos ni aerosoles inamables cerca del
horno.
- Los elementos inamables o aerosoles pueden causar incendios o
una explosión.
No introduzca los dedos, sustancias extrañas ni objetos metálicos
como alleres o agujas en las entradas, tomacorrientes u oricios.
Si se introducen sustancias extrañas en alguno de estos oricios,
comuníquese con el distribuidor del producto o con el centro de
servicio técnico más cercano.
No altere ni haga ajustes ni reparaciones en la puerta. Bajo ninguna
circunstancia debe quitar la puerta o la coraza externa del horno.
No almacene ni utilice el horno al aire libre.
Nunca use este electrodoméstico con otros nes que no sean cocinar.
- El uso de este electrodoméstico para otro n que no sea cocinar
puede provocar un incendio.
Abra la tapa o el tapón de recipientes sellados (botellas de té tónico
de hierbas, mamaderas, botellas de leche, etc.) antes de calentarlos.
Haga un oricio en los alimentos con cáscara (huevos, castañas, etc.)
con un cuchillo, antes de cocinarlos.
- No hacerlo puede provocar quemaduras o lesiones.
Nunca caliente en recipientes de plástico ni papel y no los utilice
para cocinar.
- Podría provocar un incendio.
No caliente comida envuelta en papel de revistas, periódicos, etc.
- Se podría provocar un incendio.
No abra la puerta cuando los alimentos en el horno se están
quemando.
- Si lo hace, esto provoca una entrada de oxígeno que puede causar
que los alimentos se prendan fuego.
No aplique presión excesiva a la puerta o al interior del
electrodoméstico. No golpee la puerta o la parte interior del
electrodoméstico.
- Colgarse de la puerta puede provocar fallas en el producto y
causar lesiones graves.
- Si la puerta está dañada, no use el electrodoméstico.
Comuníquese con un centro de servicios.
NE59M4320_DG68-00882A-01_MES.indd 13 2/16/2017 3:45:50 PM
14 Español
Instrucciones de seguridad importantes
Instrucciones de seguridad importantes
No sostenga alimentos con los manos durante o inmediatamente
después de cocinar.
- Use guantes de cocina. Los alimentos pueden estar muy calientes
y podría quemarse.
- Use guantes o guantes de cocina, ya que la manija y las
supercies del horno pueden estar lo sucientemente calientes
como para causar quemaduras luego de cocinar.
PRECAUCIONES PARA EL USO
PRECAUCIÓN
Si la supercie está rajada, apague el electrodoméstico.
- No hacerlo puede provocar una descarga eléctrica.
La vajilla y los envases pueden calentarse. Manipúlelos con cuidado.
Los alimentos calientes y el vapor pueden provocar quemaduras.
Retire cuidadosamente las tapas de los envases, dirigiendo el vapor
lejos de las manos y la cara.
Retire las tapas de los frascos de alimentos para bebé antes de
calentarlos. Después de calentar los alimentos para bebé, revuelva
bien para distribuir el calor en forma pareja. Siempre pruebe los
alimentos para corroborar la temperatura antes de alimentar al bebé.
Los frascos de vidrio o la supercie de los alimentos pueden parecer
más fríos que el interior, el cual puede estar lo sucientemente
caliente como para quemar la boca de un niño.
Tenga cuidado dado que las bebidas o los alimentos pueden estar
muy calientes después de calentarlos.
- Especialmente cuando alimenta a un niño. Compruebe que se
enfrió lo suciente.
Tenga cuidado al calentar líquidos como, por ejemplo, agua u otras
bebidas.
- Asegúrese de revolver durante o después de cocinar.
- Evite utilizar un recipiente resbaladizo con cuello angosto.
- Espere al menos 30 segundos después del calentamiento antes de
quitar el líquido calentado.
- No hacerlo puede provocar el derrame del contenido y causar
quemaduras.
No se pare sobre el electrodoméstico ni coloque sobre él objetos
(como ropa sucia, fundas para hornos, velas encendidas, cigarrillos
encendidos, platos, productos químicos, objetos metálicos, etc.).
- Artículos tales como paños pueden quedar enganchados en la
puerta.
- Se pueden producir descargas eléctricas, incendios, problemas con
el producto o lesiones personales.
No haga funcionar el electrodoméstico con las manos húmedas.
- Se puede producir una descarga eléctrica.
No rocíe sustancias volátiles como insecticidas en la supercie del
electrodoméstico.
- Además de ser perjudiciales para las personas, pueden producirse
descargas eléctricas, incendios o problemas en el producto.
No acerque el rostro ni el cuerpo al electrodoméstico mientras es
cocinando o al abrir la puerta inmediatamente después de la cocción.
- Asegúrese de que los niños no se acerquen demasiado al
electrodoméstico.
- No hacerlo puede provocar quemaduras en los niños.
NE59M4320_DG68-00882A-01_MES.indd 14 2/16/2017 3:45:50 PM
Español 15
Instrucciones de seguridad importantes
No coloque alimentos ni objetos pesados sobre el borde de la puerta
del horno.
- Si abre la puerta, los alimentos o el objeto podrían caerse y
provocar quemaduras o lesiones.
No enfríe abruptamente la puerta, el interior del electrodoméstico ni
el plato vertiendo agua sobre estas partes durante o después de la
cocción.
- Esto puede provocar daños en el electrodoméstico. El vapor o el
rocío de agua pueden provocar quemaduras o lesiones.
No haga funcionar el horno mientras está vacío excepto para auto-
limpieza.
No descongele bebidas congeladas en botellas de cuello angosto.
Las botellas pueden romperse.
No raye el vidrio de la puerta del horno con un objeto puntiagudo.
- Esto puede provocar que el vidrio se dañe o se rompa.
No almacene nada directamente encima del electrodoméstico cuando
está en funcionamiento.
No utilice recipientes sellados. Quíteles los sellos y las tapas antes
de cocinar. Los recipientes sellados pueden explotar debido a la
acumulación de presión incluso después de que el horno se ha
apagado.
Tenga cuidado de que los alimentos que está cocinando en el horno
no entren en contacto con el elemento calentador.
- Se podría provocar un incendio.
No caliente los alimentos en exceso.
- El sobrecalentamiento podría provocar un incendio.
ADVERTENCIAS FUNDAMENTALES
PARA LA LIMPIEZA
PRECAUCIÓN
No rocíe agua directamente sobre el electrodoméstico para limpiarlo.
No utilice benceno, diluyente ni alcohol para limpiar el
electrodoméstico.
- Esto puede provocar decoloración, deformación, daños, descarga
eléctrica o incendio.
Tenga cuidado de no lastimarse cuando limpia el electrodoméstico
(exterior/interior).
- Puede lastimarse con los bordes puntiagudos del
electrodoméstico.
No limpie el electrodoméstico con un limpiador a vapor.
- Esto puede provocar corrosión.
Mantenga limpia la parte interna del horno. Las partículas de
alimentos o los aceites salpicados que se adhieren a las paredes o
al piso pueden causar daños en la pintura y reducir la eciencia del
horno.
NE59M4320_DG68-00882A-01_MES.indd 15 2/16/2017 3:45:51 PM
16 Español
Introducción a su nueva estufa
Introducción a su nueva estufa
Descripción general
05
02
03
04
06
07
08
09
10
11
01
01 Panel de control del
horno (Consulte la
página 22 para obtener
más información)
02 Supercie de vidrio 03 Puerta del horno
04 Cajón de
almacenamiento
05 * Perillas de control
de la supercie
(Consulte la página
18 para obtener más
información)
06 Pestillo de auto-limpieza
y limpieza con vapor
07 Interruptor de la luz
automática del horno
08 * Luz del horno 09 Ventilador de
convección
10 Posición del estante 11 Junta selladora
Elementos incluidos con su estufa
* Estantes de alambre (2)
NOTA
Si necesita un accesorio marcado con un *, puede adquirirlo en el Centro de contacto de
Samsung (1-800-726-7864).
NE59M4320_DG68-00882A-01_MES.indd 16 2/16/2017 3:45:51 PM
Español 17
Antes de comenzar
Antes de comenzar
Limpie el horno a fondo antes de utilizarlo por primera vez. Luego, retire los accesorios,
programe el horno para hornear y luego haga funcionar el horno a 400 °F durante 1 hora.
Se notará un olor característico. Esto es normal.
Asegúrese de que su cocina se encuentre bien ventilada durante el período de
acondicionamiento.
Sugerencias para ahorrar energía
Durante la cocción, la puerta del horno debe permanecer cerrada excepto para dar vuelta
los alimentos.
No abra la puerta con frecuencia durante la cocción para mantener la temperatura del
horno y ahorrar energía.
Si el tiempo de cocción supera los 30 minutos, puede apagar el horno 5-10 minutos antes
del n del tiempo de cocción para ahorrar energía. El calor residual completará el proceso
de cocción.
Para ahorrar energía y reducir el tiempo necesario para volver a calentar el horno,
planique el uso del horno para evitar tener que apagarlo entre la cocción de un alimento
y el siguiente.
Cuando sea posible cocine más de un alimento a la vez.
Cocción en cubierta
Acerca de la cocción en cubierta
PRECAUCIÓN
ANTES DE COCINAR
No utilice la supercie de vidrio de la cubierta como tabla para cortar.
No coloque ni almacene sobre la cubierta de vidrio elementos susceptibles de derretirse o
prenderse fuego, aun cuando no se encuentre en uso.
Encienda las unidades de supercie solamente después de colocar recipientes de cocción
sobre ellas.
No almacene objetos pesados por encima de la supercie de la cubierta. Podrían caerse y
dañar tal supercie
PRECAUCIÓN
DURANTE LA COCCIÓN
Mientras la estufa esté en uso, no coloque sobre ella papel de aluminio ni elementos
plásticos tales como saleros y pimenteros, apoyos para cucharas, ni envoltorios plásticos.
El aire caliente que sale por la abertura de ventilación podría derretir plásticos o hacer
arder elementos inamables.
Asegúrese de que se encuentre encendida la unidad de supercie correcta.
Nunca cocine directamente sobre el vidrio. Siempre utilice recipientes.
Siempre coloque la cacerola o sartén en el centro de la unidad de supercie sobre la cual
está cocinando.
Nunca deje las unidades de supercie sin atención mientras las utiliza reguladas a altas
temperaturas. Los derrames por exceso de hervor producen humo y los derrames de
sustancias grasas pueden arder en llamas.
Apague las unidades de supercie antes de retirar los recipientes de cocción.
No utilice películas plásticas para tapar los alimentos. El plástico podría derretirse, caer
sobre la supercie y resultar muy difícil de quitar.
NE59M4320_DG68-00882A-01_MES.indd 17 2/16/2017 3:45:51 PM
18 Español
Cocción en cubierta
Cocción en cubierta
Ubicación de los elementos radiantes de la supercie y los controles
Las perillas controlan los elementos radiantes de la supercie de cocción tal como se indica a
continuación.
01
02
06 07
05
04
03
01 Delantero izquierdo:
6”/9”, 3000 W
02 Trasero izquierdo:
6”, 1200 W
03 Delantero derecho:
9”/12”, 3000 W
04 Trasero derecho:
6”, 1200 W
05 Centro de calentamiento:
100 W
06 Indicador de supercie
caliente
07 Indicador de cubierta
encendida
PRECAUCIÓN
DESPUÉS DE COCINAR
No toque las unidades de supercie hasta que se hayan enfriado.
La supercie podría estar caliente aún y producirle quemaduras si toca la supercie de
vidrio antes de que se haya enfriado lo suciente.
Limpie inmediatamente los derrames sobre las áreas de cocción, a n de evitar un duro
trabajo de limpieza más adelante.
Si hay gabinetes de almacenamiento instalados directamente sobre la supercie de
limpieza, procure que sean elementos de uso infrecuente y asegúrese de que puedan ser
almacenados con seguridad en un lugar que reciba calor. Las temperaturas alcanzadas
pueden resultar inseguras para elementos tales como líquidos volátiles, agentes
limpiadores o spray en aerosol.
Sobre los elementos radiantes de la supercie
La temperatura se eleva en forma gradual y pareja. Al elevarse la temperatura, el elemento
irradiará un color rojo. Para mantener la regulación seleccionada, el elemento alternará ciclos
de encendido y apagado. El elemento calentador retiene calor suciente como para suministrar
calor suciente y uniforme durante su ciclo de apagado. Para mejorar la eciencia de cocción,
apague el elemento varios minutos antes de que se complete la cocción. Esto permitirá que el
calor residual complete el proceso de cocción.
NOTA
Los elementos radiantes tienen un dispositivo limitante que les permite alternar en ciclos
de encendido y apagado aun en la regulación alta. Esto ayuda a evitar daños a la cubierta
vitrocerámica. La alternancia en ciclos en la regulación alta es normal y puede ocurrir si
el recipiente de cocción es demasiado pequeño para el elemento radiante o si la base del
recipiente no es plana.
NE59M4320_DG68-00882A-01_MES.indd 18 2/16/2017 3:45:52 PM
Español 19
Cocción en cubierta
Indicador de supercie caliente
Se ilumina cuando la unidad se encuentra encendida o caliente al tacto.
Permanece encendido aún después de que se haya apagado la unidad.
Emite luz hasta que la unidad se haya enfriado hasta aproximadamente 150 °F.
Áreas de cocción
Las áreas de cocción de su estufa están señaladas por círculos permanentes sobre la
supercie de cocción de vidrio. Para lograr la máxima eciencia de cocción, seleccione un
tamaño de recipiente adecuado con relación al elemento calentador.
Los recipientes de cocción no deben proyectarse más de ½” a 1” más allá del área de
cocción.
Cuando un control se encuentra encendido, se puede ver una luz tenue a través de la
supercie de cocción de vidrio. El elemento alternará ciclos de encendido y apagado para
mantener la regulación de temperatura seleccionada previamente, aun cuando se hayan
regulado temperaturas altas.
Para mayor información sobre la selección de tipos correctos de recipientes de cocción,
consulte la sección "Utilización de los recipientes de cocción correctos", en la página 20.
Como regular su estufa para la cocción de cubierta
PRECAUCIÓN
Los elementos de supercie pueden estar calientes y pueden causar quemaduras.
No toque los elementos de supercie hasta que se hayan enfriado lo suciente.
Nunca deje la comida desatendida cuando haya regulado temperaturas altas o de
medianas a altas. Los derrames por exceso de hervor producen humo y los derrames de
sustancias grasas pueden arder.
Asegúrese de girar la perilla de control a OFF (APAGADO) cuando termine de cocinar.
Perilla de control de las unidades de supercie
1
2
A
B
1
2
Simple
(Trasera izquierda, Trasera derecha)
Doble
(Delantera izquierda, Delantera derecha)
1. Empuje la perilla hacia adentro.
2. Gire en cualquier dirección hasta la regulación deseada.
Posición A : Quemador simple
Posición B : Quemador doble
PRECAUCIÓN
La zona entre las regulaciones alta (HI) y apagada (OFF) no es apropiada para cocinar.
Regulaciones recomendadas
REGULACIÓN TIPO DE COCCIÓN
ALTO
Cocción inicial de la mayoría de las comidas, hacer hervir agua, asar en
cacerola
MEDIO ALTO Mantener un hervor rápido, frituras, frituras sumergidas en grasa
MEDIO
Mantener un hervor lento, reducir salsas y jugos de cocción, cocción al
vapor de vegetales
MEDIO BAJO Mantener el proceso de cocción, escalfado, cocer guisados.
BAJO Mantener la comida caliente, derretir, hervir a fuego lento
NE59M4320_DG68-00882A-01_MES.indd 19 2/16/2017 3:45:52 PM
20 Español
Cocción en cubierta
Cocción en cubierta
Utilización de los recipientes de cocción correctos
Utilizar los recipientes de cocción correctos puede evitar muchos problemas, tales como cocción
despareja o tiempos de cocción demasiado largos. Utilizar las cacerolas y sartenes adecuadas
redundará en menor tiempo de cocción y los alimentos se cocinarán en forma más pareja.
Controle que el fondo sea plano haciendo girar
una regla sobre la base del recipiente.
CORRECTO INCORRECTO
Fondo plano y lados verticales.
Tapas bien ajustadas.
El peso del mango no inclina el
recipiente.
El recipiente está bien equilibrado.
El tamaño del recipiente guarda
adecuada relación con la cantidad de
alimento que se preparará y con el
elemento calentador.
Hecho de un material que es buen
conductor del calor.
Siempre haga corresponder el diámetro del
recipiente con el diámetro del elemento
calentador.
Recipientes cuyos fondos están curvados o
deformados.
El recipiente sobresale del elemento en más
de media pulgada.
El recipiente es más pequeño que el
elemento calentador.
Mango demasiado pesado causa inclinación
del recipiente.
Uso del centro de calentamiento
El Warming Center (Centro de calentamiento), ubicado en la parte posterior central de la supercie
de vidrio mantendrá calientes los alimentos ya cocidos a temperatura apta para servir.
NOTA
El calentador de supercie no se pondrá al rojo como los demás elementos de cocción.
PRECAUCIÓN
No mantenga alimentos sobre el centro de calentamiento por más de dos horas.
Utilice únicamente recipientes y vajilla recomendada como segura para uso en horno y sobre
supercies de cocción.
Siempre utilice agarradores o guantes aislantes cuando retira los alimentos del centro de
calentamiento ya que los recipientes y los platos estarán calientes.
Cuando se calientan pasteles y panes, la tapa debe tener una abertura para permitir que escape
la humedad.
Siempre comience con alimentos calientes. Consumir alimentos que fueron colocados sobre el
centro de calentamiento crudos o fríos podría causar enfermedades.
1. Encienda el centro de calentamiento. Presione la tecla Warming Center On/Off (Centro de
calentamiento Encender/Apagar).
2. Regule la potencia al nivel deseado. Presionar la tecla Warming Center Level (Centro de
calentamiento Nivel) una vez lo regulará en el nivel bajo.
Presione la tecla dos veces para el nivel medio, tres veces para el nivel alto.
3. Apague el centro de calentamiento. Presione la tecla Warming Center On/Off (Centro de
calentamiento Encender/Apagar).
NOTA
Presionar la tecla OFF/CLEAR (APAGAR/BORRAR) no apaga el centro de calentamiento.
Para obtener óptimos resultados, todas las comidas en el centro de calentamiento deben
cubrirse con una tapa o papel de aluminio. Cuando se calientan pasteles o panes, la tapa debe
tener una abertura para permitir que escape la humedad.
Regulaciones recomendadas
NIVEL TIPO DE ALIMENTO
BAJO Panes y pasteles, guisados, jugos de cocción, huevos
MEDIO Plato de mesa con comida, sopa (crema), vegetales, salsas, guisos, carnes
ALTO Comidas fritas, sopas (líquidas), bebidas calientes
NE59M4320_DG68-00882A-01_MES.indd 20 2/16/2017 3:45:53 PM
Español 21
Cocción en cubierta
Selección de los recipientes de cocción correctos
El material del que están hechos sus recipientes de cocción determina que tan rápida y
parejamente se transere el calor del elemento calentador de la supercie al fondo del
recipiente.
ALUMINIO - Excelente conductor de calor. Algunos tipos de alimentos causarán el
oscurecimiento del aluminio. (Los recipientes de aluminio anodizado son resistentes a
las manchas y a las picaduras). Si se deslizan recipientes de aluminio sobre la cubierta
vitrocerámica, podrían quedar marcas de metal semejantes a rayaduras. Retire estas
marcas no bien la cubierta se enfríe.
COBRE - Excelente conductor de calor pero su color se altera con facilidad. Puede dejar
marcas de metal sobre la supercie vitro-cerámica (ver arriba).
ACERO INOXIDABLE - Lento conductor de calor, los resultados de cocción pueden ser
disparejos. Es duradero, fácil de limpiar y resistente a las manchas.
HIERRO FUNDIDO - Mal conductor del calor; retiene el calor muy bien. Una vez alcanzada
la temperatura necesaria, produce cocción uniforme. Se desaconseja su uso en cubiertas
vitrocerámicas.
UTENSILIOS ESMALTADOS - Las características de conducción de calor dependerán del
material base. Los revestimientos de porcelana deben ser lisos para evitar rayaduras en
las cubiertas vitrocerámicas.
VIDRIO - Lento conductor de calor. Se desaconseja su uso en supercies de cocción
cerámicas porque puede causar rayaduras.
Protección de la cubierta
Limpieza
Limpie la cubierta antes de utilizarla por primera vez.
Limpie la cubierta diariamente o después de cada uso. Esto mantendrá la buena
apariencia de la cubierta y puede evitar daños.
Si durante la cocción ocurre un derrame, límpielo inmediatamente del área de cocción
mientras esté caliente para evitar tener que hacer un duro trabajo de limpieza más
adelante. Con extremo cuidado, limpie el derrame con una toalla limpia y seca.
No permita que los derrames permanezcan mucho tiempo en el área de cocción o las
terminaciones de la cubierta.
No utilice polvos limpiadores abrasivos, paños abrasivos ni esponjas metálicas, porque
producirán rayaduras en la cubierta.
No utilice cloro, amoníaco ni otros productos limpiadores no especícamente
recomendados para ser usados en supercies vitrocerámicas.
Cómo evitar marcas y rayaduras
No utilice recipientes de cocción de vidrio. Pueden causar rayaduras en la cubierta.
No coloque un trébedes o un aro para wok entre la cubierta y el recipiente.
Estos elementos pueden marcar o rayar la cubierta.
Asegúrese de que la cubierta y el fondo del recipiente se encuentren limpios.
No deslice recipientes metálicos sobre la cubierta.
Prevención de manchas
No utilice paños ni esponjas sucias para limpiar la supercie de la cubierta.
Quedará una película que podría causar manchas sobre la supercie de la cubierta cuando
se caliente el área.
La cocción continuada sobre una supercie sucia puede causar manchas permanentes.
Prevención de otros daños
No permita que plásticos, azúcar o alimentos con alto contenido de azúcar se derritan
sobre la cubierta. Si esto ocurriese, limpie inmediatamente.
No permita que un recipiente quede seco por hervor prolongado, ya que esto dañará la
cubierta y el recipiente.
No utilice la cubierta como mesada ni como tabla para cortar.
No cocine alimentos directamente sobre la cubierta. Use siempre los recipientes de
cocción adecuados.
NE59M4320_DG68-00882A-01_MES.indd 21 2/16/2017 3:45:53 PM
22 Español
Funcionamiento del horno
09 SELF CLEAN (AUTO-LIMPIEZA): Use para seleccionar la función de auto-limpieza del
horno.
10 EASY COOK (COCCIÓN FÁCIL): Use para recuperar el ajuste de la receta de cocción fácil del
horno.
11 TIMER ON/OFF (ACTIVAR/DESACTIVAR TEMPORIZADOR): Use para programar o cancelar el
temporizador para minutos. El temporizador para minutos no inicia ni detiene la cocción.
12 COOKING TIME (TIEMPO DE COCCIÓN): Presione y luego utilice el teclado numérico para
programar la duración de la cocción para los alimentos en cuestión. El horno se apagará
cuando haya transcurrido el tiempo de cocción.
13 DELAY START (INICIO RETARDADO): Presione para programar que el horno se active y
detenga automáticamente a las horas que usted je. (Solo hornear, hornear/asar por
convección, tiempo de cocción y auto-limpieza.)
14 CLOCK (RELOJ): Use para jar la hora del día.
15 LUZ: Presione para encender o apagar la luz del horno.
16 START/SET (INICIO/CONFIGURAR): Presione para iniciar cualquier función de cocción o de
limpieza en el horno.
17 OFF/CLEAR (APAGAR/BORRAR): Presione para cancelar todas las operaciones del horno
excepto reloj y temporizador.
Funcionamiento del horno
Panel de control del horno
LEA LAS INSTRUCCIONES CON ATENCIÓN ANTES DE UTILIZAR EL HORNO. Para obtener
un funcionamiento satisfactorio del horno, familiarícese con las diversas características y
funciones que se describen a continuación. Encontrará instrucciones detalladas para cada
característica y función más adelante en este manual.
03 07 04
08
05 06 01
1110 12 13 14 17 15
02 1609
01 PANTALLA: Muestra la hora del día, la temperatura del horno, si el horno está en el modo
de hornear, asar a la parrilla o auto-limpieza y las horas jadas para el temporizador o
las operaciones automáticas del horno.
02 TECLADO NUMÉRICO: Utilícelo para marcar o jar cualquier función que requiera números
tales como la hora en el reloj, el temporizador, la temperatura del horno y la hora de
comienzo y la duración de la operación para el caso de horneado temporizado.
03 CONVECTION BAKE (HORNEAR POR CONVECCIÓN): Use para seleccionar la función de
hornear por convección del horno.
04 CONVECTION ROAST (ASAR POR CONVECCIÓN): Use para seleccionar la función de asar
por convección del horno.
05 BAKE (HORNEAR): Use para seleccionar la función de hornear del horno.
06 BROIL (ASAR A LA PARRILLA): Use para seleccionar la función de asar a la parrilla del
horno.
07 KEEP WARM (MANTENER TEMPERATURA): Use para seleccionar la función de mantener
temperatura del horno para mantener calientes los alimentos cocidos.
08 STEAM CLEAN (LIMPIEZA CON VAPOR): Use para seleccionar la función de limpieza con
vapor del horno.
NE59M4320_DG68-00882A-01_MES.indd 22 2/16/2017 3:45:54 PM
Español 23
Funcionamiento del horno
Ajuste del reloj
El reloj debe ajustarse para mostrar la hora correcta y permitir el buen funcionamiento de las
opciones de temporizador del horno.
La hora del día no se puede cambiar mientras estén en proceso una cocción regida por el
temporizador, una cocción temporizada diferida o un ciclo de auto-limpieza.
Este modelo solo dispone del formato de 12 horas.
Cómo ajustar el reloj
1. Inicio de la conguración. Presione Clock (Reloj).
2. Ingrese la hora del momento en horas y minutos mediante el teclado numérico, por
ejemplo: 1, 3, 0, para 1:30.
3. Presione Clock (Reloj) o START/SET (INICIO/CONFIGURAR) para guardar los cambios.
Cómo programar el temporizador de cocina
El temporizador de cocina funciona como un temporizador adicional que emitirá un sonido
agudo cuando el tiempo jado haya transcurrido. No inicia ni detiene las funciones de cocción.
Puede usar el temporizador de cocina con cualquiera de las funciones del horno.
Cómo programar el temporizador
1. Encienda el temporizador. Presione Timer On/Off (Activar/Desactivar temporizador).
2. Ingrese el tiempo que desea. Ingrese el tiempo que desea mediante el teclado numérico,
por ejemplo 1, 5. El temporizador puede congurarse para cualquier cantidad de tiempo,
desde 1 minuto hasta 9 horas y 59 minutos.
Si comete un error, presione Timer On/Off (Activar/Desactivar temporizador) e ingrese la
cantidad de tiempo nuevamente.
3. Active el temporizador. Presione Timer On/Off (Activar/Desactivar temporizador).
4. Cuando haya transcurrido el tiempo jado, el horno emitirá un sonido agudo y en la
pantalla se verá "End" (Fin) hasta que usted presione la tecla Timer On/Off (Activar/
Desactivar temporizador). El temporizador se puede desactivar en cualquier momento
presionando la tecla Timer On/Off (Activar/Desactivar temporizador).
NE59M4320_DG68-00882A-01_MES.indd 23 2/16/2017 3:45:54 PM
24 Español
Funcionamiento del horno
Funcionamiento del horno
Inicio retardado
En una cocción con inicio retardado, el temporizador del horno enciende y apaga el horno a las
horas que usted seleccione con anticipación.
La función de inicio retardado se puede utilizar únicamente en combinación con otra
operación de cocción
(hornear, hornear por convección, asar por convección,
cocción lenta o deshidratar).
Se puede programar el horno para un inicio retardado antes de seleccionar las otras
operaciones de cocción.
Se debe ajustar el reloj en la hora actual.
Cómo programar el horno para inicio diferido
1. Coloque la(s) parrilla(s) y los alimentos en el horno.
2. Ingrese la conguración. Presione la tecla para denir la operación de cocción que desea,
por ejemplo Bake (Hornear). La temperatura predeterminada es de 350 °F.
3. Utilice el teclado numérico para ingresar la temperatura que desea, por ejemplo 375 °F.
4. Presione Cooking Time (Tiempo de cocción).
5. Ingrese el tiempo de cocción que desea, por ej. 45 minutos, mediante el teclado numérico.
El tiempo de cocción se puede jar para cualquier duración desde 1 minuto hasta 9 horas
y 59 minutos.
6. Presione Delay Start (Inicio retardado).
7. Ingrese la hora a la cual desea que se encienda el horno, por ejemplo 4:30, mediante el
teclado numérico.
8. Presione START/SET (INICIO/CONFIGURAR). A la hora jada, se emitirá una breve señal
sonora. El horno comenzará la cocción.
Cocción por temporizador
En un proceso de cocción regido por el temporizador, el horno se enciende inmediatamente y
cocina durante el tiempo que usted je. Una vez completado ese tiempo de cocción, el horno
se apaga automáticamente.
La función de cocción regida por temporizador se puede utilizar únicamente en
combinación con otra operación de cocción (hornear, hornear por convección, asar por
convección, cocción lenta o deshidratar).
Cómo programar el horno para cocción por temporizador
1. Ingrese la conguración. Presione la tecla para denir la operación de cocción que desea, por
ejemplo Bake (Hornear). La temperatura predeterminada es de 350 °F.
2. Ingrese la temperatura que desea, por ejemplo 375 °F, mediante el teclado numérico.
3. Presione Cooking Time (Tiempo de cocción).
4. Ingrese el tiempo de cocción que desea, por ej. 45 minutos, mediante el teclado numérico.
El tiempo de cocción se puede jar para cualquier duración desde 1 minuto hasta 9 horas y
59 minutos.
5. Presione START/SET (INICIO/CONFIGURAR) para iniciar la cocción. El indicador de temperatura
comenzará a variar una vez que la temperatura del horno alcance 175 °F.
El horno continuará cocinando hasta que haya transcurrido el tiempo jado, luego se apagará
automáticamente salvo que se haya programado la función de mantener la temperatura.
(Consulte la sección sobre la función de mantener temperatura en la página 30.)
6. Puede cancelar un tiempo de cocción en cualquier momento ajustando el tiempo de cocción
en 0 minutos. (Presione Cooking Time (Tiempo de cocción) -> ingrese 0 -> presione START/SET
(INICIO/CONFIGURAR))
Cuando haya transcurrido el tiempo de cocción, la estufa emite una señal sonora 10 veces.
PRECAUCIÓN
Tenga precaución al utilizar las funciones timed cooking (Cocción con temporizador) o delay
start (inicio retardado). Utilice estas funciones para cocinar carnes curadas o congeladas y
la mayor parte de las frutas y vegetales. Los alimentos que se pueden echar a perder con
facilidad tales como leche, huevos, pescado, carnes (incluidas las aves) deben enfriarse
previamente en el refrigerador. Aun enfriados, no deben permanecer en el horno durante más
de 1 hora antes de que se inicie la cocción y una vez completada la cocción deben retirarse a
la brevedad. La ingestión de alimentos en mal estado puede producir intoxicación alimentaria.
NE59M4320_DG68-00882A-01_MES.indd 24 2/16/2017 3:45:54 PM
Español 25
Funcionamiento del horno
Cómo encender y apagar la luz del horno
La luz del horno se enciende automáticamente cuando se abre la puerta.
La luz del horno se apaga automáticamente cuando se cierra la puerta.
La luz del horno se puede encender y apagar manualmente presionando la tecla .
Ajustes mínimos y máximos
Todas las funciones enumeradas en la siguiente tabla tienen ajustes de tiempo o temperatura
mínimos y máximos. Se oirá una señal sonora cada vez que se presione una tecla del panel de
control y el dato ingresado haya sido aceptado. Si la temperatura o el tiempo ingresados se
encuentran por debajo del mínimo o por arriba del valor ajustable máximo para la función en
cuestión, sonará un tono de error en la forma de un sonido más prolongado.
FUNCIÓN MÍNIMO MÁXIMO
Hornear 175 °F (80 °C) 550 °F (285 °C)
Asar a la parrilla
BAJA ALTA
Hornear por
convección
175 °F (80 °C) 550 °F (285 °C)
Asar por convección 175 °F (80 °C) 550 °F (285 °C)
Centro de
calentamiento
- 3 h
Mantener
temperatura
- 3 h
Entibiar para leudado - 12 h
Auto-limpieza 2 h 5 h
Limpieza con vapor 20 min 20 min
Uso de las parrillas del horno
Posiciones de las parrillas en el horno
1
2
3
4
5
6
7
Posición recomendada de las parrillas para
cocción
Tipo de alimento
Posición de la
parrilla
Hamburguesas a la parrilla 7
Carnes o cortes pequeños
de ave, pescado, a la
parrilla
5-7
Panqués, pasteles molde
savarin, tartas congeladas,
guisos
4 o 3
Pasteles de ángel, carnes
asadas de pequeño tamaño
2
Pavo, carnes asadas de
gran tamaño, jamones,
pizza fresca
1
Esta tabla es para referencia solamente.
NE59M4320_DG68-00882A-01_MES.indd 25 2/16/2017 3:45:54 PM
26 Español
Funcionamiento del horno
Funcionamiento del horno
Colocación de parrillas y recipientes
3 4
Parrilla del horno simple
o
Colocar los moldes o las charolas lo más cerca
posible del centro del horno producirá los mejores
resultados. Si hornea con más de un recipiente,
colóquelos de manera tal que cada uno tenga 1
a
de espacio libre a su alrededor.
Cuando hornee en una única parrilla, coloque la
parrilla del horno en la posición 3 o 4. Consulte la
gura de la izquierda.
5
3
Parrilla del horno múltiple
Cuando hornee galletas en parrillas múltiples,
coloque las parrillas en las posiciones 3 y 5.
Consulte la gura de la izquierda.
Uso de múltiples parrillas del horno
Tipo de horneado Posición de la parrilla
Tortas y galletas 3 y 5
Antes de usar las parrillas
El horno tiene dos parrillas.
Cada parrilla tiene topes que requieren una colocación correcta sobre las guías. Estos topes
impedirán que la parrilla se salga completamente.
RETIRAR LAS PARRILLAS
1. Jale la parrilla directamente hacia afuera hasta que se trabe.
2. Levante la parte delantera de la parrilla y extráigala.
RECOLOCAR LAS PARRILLAS
1. Coloque el extremo de la parrilla sobre la guía.
2. Incline el extremo delantero y empuje la parrilla hacia adentro.
PRECAUCIÓN
No use papel de aluminio para cubrir las parrillas ni el fondo del horno. Tales acciones
entorpecerían la circulación del calor, crearían problemas en el proceso de horneado y
podrían dañar el fondo del horno.
Coloque las parrillas en la distribución deseada solamente cuando el horno se encuentre
frío.
Hornear
El horno puede programarse para hornear a cualquier temperatura en el rango de 175 °F a
550 °F.
La temperatura y el tiempo de horneado varían según los ingredientes y el tamaño y la forma
de la bandeja de hornear utilizada. Los recubrimientos oscuros y antiadherentes cocinan los
alimentos más rápidos y los doran más.
Cómo ajustar la temperatura
1. Comience el proceso de ajuste. Presione Bake (Hornear). La temperatura predeterminada
es de 350 °F.
2. Ingrese la temperatura que desea mediante el teclado numérico, por ejemplo 3, 7, 5.
3. Active la función de hornear. Presione START/SET (INICIO/CONFIGURAR). El indicador de
temperatura comenzará a variar una vez que la temperatura del horno alcance 175 °F.
4. Si desea cancelar el horneado o si terminó, presione OFF/CLEAR (APAGAR/BORRAR).
Coloque los alimentos en el horno después de precalentarlo, si así lo requiere la receta.
El precalentamiento es muy importante para lograr buenos resultados cuando se
hornean tortas, pasteles, galletas, masas y panes. Cuando el horno haya alcanzado la
temperatura deseada, la estufa emitirá una señal sonora 6 veces.
NOTA
Por razones de rendimiento, el ventilador de convección puede encenderse o apagarse durante
el funcionamiento.
NE59M4320_DG68-00882A-01_MES.indd 26 2/16/2017 3:45:55 PM
Español 27
Funcionamiento del horno
Cómo ajustar la temperatura durante el proceso de cocción
1. Inicio de la conguración.
Presione Bake (Hornear). La pantalla mostrará la temperatura jada hasta el momento,
por ejemplo 375 °F.
2. Ingrese la temperatura que desea, por ejemplo 425 °F, mediante el teclado numérico.
3. Complete el ingreso presionando START/SET (INICIO/CONFIGURAR).
Hornear por convección
1
2
3
4
5
6
7
Utilizar la función de hornear por convección,
le permitirá una cocción más rápida. Se puede
programar el horno para hornear por convección
a temperaturas de entre 175 °F y 550 °F. En el
horneado por convección se activa un ventilador
para hacer circular el calor del horno en forma
pareja y continua. Esta mejor distribución del
calor posibilita la cocción pareja y excelentes
resultados cuando se utilizan múltiples parrillas al
mismo tiempo. Las comidas que se cocinen sobre
una única parrilla generalmente se cocinarán en
forma más rápida y pareja si se utiliza la función
de hornear por convección. La cocción utilizando
múltiples parrillas en el horno puede resultar
en tiempos de cocción un poco más largos para
ciertas comidas, pero a n de cuentas se ahorra
tiempo. Los panes, pasteles y masas se doran en
forma más pareja.
Consejos para el horneado por convección
El tiempo que ahorre dependerá del tipo y de la cantidad de alimento que esté cocinando.
Al hornear galletas, se aconseja utilizar charolas sin lados o con lados muy bajos para permitir
que el aire caliente circule alrededor de la comida. Utilizar una charola de supercie oscura
permitirá una cocción más rápida.
Cuando hornee por convección con una única parrilla, colóquela en la posición 3 o 4. Si cocina
con parrillas múltiples, colóquelas en la posición 3 y 5.
Si hornea una torta o pastel, el modo de hornear simple producirá mejores resultados.
Cómo ajustar el horno para hornear por convección
1. Active el modo de hornear por convección.
Presione Bake (Hornear por convección). La temperatura predeterminada es de 350 °F.
2. Ingrese la temperatura que desea, por ejemplo 400 °F, mediante el teclado numérico.
3. Presione START/SET (INICIO/CONFIGURAR) para iniciar el horneado por convección.
Conv. Bake (Hornear por convección) y la temperatura ajustada del horno, por ejemplo
400 °F, se verán en la pantalla durante 2 segundos.
El indicador de temperatura comenzará a variar una vez que la temperatura del horno
alcance 175 °F.
La estufa emitirá una señal sonora 6 veces cuando el horno alcance la temperatura
deseada.
4. Para apagar o cancelar el horneado por convección presione OFF/CLEAR (APAGAR/
BORRAR).
Cuando se abre la puerta del horno, el ventilador del horno de convección se apaga.
NO DEJE la puerta del horno abierta durante mucho tiempo mientras funciona en
modo de convección porque ello podría reducir la vida útil del elemento calentador de
convección.
NOTA
Por razones de rendimiento, el ventilador de convección puede encenderse o apagarse durante
el funcionamiento.
NE59M4320_DG68-00882A-01_MES.indd 27 2/16/2017 3:45:55 PM
28 Español
Funcionamiento del horno
Funcionamiento del horno
Asar a la parrilla
El modo asar a la parrilla es el mejor para carnes, pescados y aves de hasta 1” de grosor. Asar
a la parrilla es un método de cocinar cortes tiernos de carne mediante el calor directo bajo el
elemento de asado a la parrilla del horno. La elevada temperatura realiza una cocción rápida y
deja el exterior con un aspecto sabroso y dorado.
Posición de traba para asar a la parrilla
Posición de traba para asar a la
parrilla
Deje la puerta abierta en la posición de traba para
asar a la parrilla. La puerta se mantendrá abierta
en esa posición por si sola; sin embargo, el horno
se mantiene a la temperatura correcta.
PRECAUCIÓN
Si se produjese fuego dentro del horno, cierre la
puerta del horno y apague el horno. Si el fuego
continúa, arroje bicarbonato de sodio sobre las
llamas o utilice un extintor de espuma. No eche
agua ni harina sobre el fuego. La harina podría
explotar y el agua puede causar que la grasa en
llamas se extienda y cause lesiones personales.
Cómo ajustar el horno para asar a la parrilla
1. Regule la temperatura de asar al nivel deseado. Presione Broil (Asar a la parrilla) una vez
para ALTA o dos veces para BAJA.
Use BAJA para cocinar comidas tales como aves o cortes de carne gruesos sin tostarlos
en exceso.
2. Active la función de asar a la parrilla. Presione START/SET (INICIO/CONFIGURAR).
Ase un lado hasta que los alimentos estén dorados. Délos vuelta y ase el otro lado.
3. Presione OFF/CLEAR (APAGAR/BORRAR) cuando haya completado la cocción o si desea
cancelarla.
Asar por convección
Asar al horno por convección es conveniente para cortes de carne tiernos y de gran tamaño,
sin cubrir.
El calor procede del elemento calentador de la parte superior. El ventilador de convección
hace circular el aire caliente en forma pareja sobre y por alrededor de la comida. Las carnes,
incluidas las aves, se doran por todos lados como si hubiesen sido cocidas en un asador
giratorio. El aire caliente rápidamente sella los alimentos dejando dentro los jugos y el
producto resulta jugoso y tierno, a la vez que el exterior adquiere un atractivo color pardo
dorado.
Cómo ajustar el horno para asar al horno por convección
1. Active el modo asar por convección.
Presione Roast (Asar por convección). La temperatura predeterminada es de 350 °F.
2. Ingrese la temperatura que desea, por ejemplo 400 °F, mediante el teclado numérico.
3. Presione START/SET (INICIO/CONFIGURAR) para iniciar el asado por convección.
Conv. Roast (Asar por convección) y la temperatura ajustada del horno, por ejemplo
400 °F, se verán en la pantalla durante 2 segundos. El indicador de temperatura
comenzará a variar una vez que la temperatura del horno alcance 175 °F. La estufa
emitirá una señal sonora 6 veces cuando el horno alcance la temperatura deseada.
4. Para apagar o cancelar el asado por convección presione OFF/CLEAR (APAGAR/BORRAR).
Cuando se abre la puerta del horno, el ventilador del horno de convección se apaga.
NO DEJE la puerta del horno abierta durante mucho tiempo mientras funciona en
modo de convección porque ello podría reducir la vida útil del elemento calentador de
convección.
NOTA
Por razones de rendimiento, el ventilador de convección puede encenderse o apagarse durante
el funcionamiento.
NE59M4320_DG68-00882A-01_MES.indd 28 2/16/2017 3:45:55 PM
Español 29
Funcionamiento del horno
Guía de recomendaciones para asar a la parrilla
Los tiempos necesarios para asar a la parrilla dependerán del tamaño, peso, espesor, temperatura
inicial y su preferencia en cuanto al grado de cocción. Esta guía está basada en carnes a temperatura
de refrigerador.
Para asar a la parrilla, utilice siempre una asadera y su rejilla. Antes de asar precaliente siempre el
horno por 5 minutos.
Alimento
Grado de
cocción
Tamaño Espesor
Ajuste de
asado a
la parrilla
Posición
de la
parrilla
Tiempo de cocción
(minutos)
1er lado 2do lado
Hamburguesas
A punto
9 hamburguesas
1” Alta 7 3:40 2:40
A punto
9 hamburguesas
¾” Alta 7 3:20 2:20
Tostada
- 9 rebanadas - Alta 7 0:32 0:30
- 9 rebanadas - Alta 6 1:00 0:45
Bistecs de
carne de res
Jugoso - 1” Alta 7 3:00-3:30 2:00-2:30
A punto - 1” Alta 6 4:30-5:00 3:30-4:00
Cocido - 1” Alta 5 8:00-9:00 6:00-7:00
Jugoso - 1½” Alta 7 3:30-4:00 2:30-3:00
A punto - 1½” Alta 6 5:30-6:00 4:30-5:00
Cocido - 1½” Alta 5 12:00-14:00 10:00-12:00
Presas de
pollo
Cocido 4.5 lb ¾”-1” Baja 4 18:00-20:00 16:00-18:00
Cocido 2-2½ lb ¾”-1” Baja 4 15:00-18:00 13:00-16:00
Costillas de
cerdo
Cocido 1 lb ½” Alta 5 8:00-8:30 6:30-7:00
Chuletas de
cordero
A punto 10 oz 1” Baja 4 5:00-6:00 4:00-5:00
Cocido 1 lb 1½” Baja 4 7:00-8:00 6:00-7:00
Filetes de
pescado
Cocido - ¼-½” Baja 5 5:00-7:00 4:00-5:00
Lonchas
de jamón
(precocidas)
- - 1½” Alta 4 4:00-5:00 3:00-4:00
Cómo utilizar la función de cocción fácil
Cocción lenta
La función Cocción lenta cocina los alimentos más lentamente a más baja temperatura del
horno.
Los tiempos de cocción prolongados permiten una mejor distribución de sabores en muchas
recetas. Esta función es ideal para asar carne, cerdo y aves. Cocinar lentamente las carnes
puede provocar que la parte exterior se oscurezca pero no se queme. Esto es normal.
1. Presione la tecla Slow Cook (Cocción lenta) una vez para ALTA o dos veces para BAJA.
2. Presione START/SET (INICIO/CONFIGURAR).
NOTA
Use solo 1 parrilla y colóquela en la posición 1 o 2 para obtener los mejores resultados.
No es necesario precalentar el horno.
Entibiar pan para leudado
Esta función automáticamente genera la temperatura óptima para el proceso de leudado del
pan y, por ende, no le corresponde ningún ajuste de temperatura.
Si presiona Bread Proof (Entibiar pan para leudado) cuando la temperatura del horno es
superior a los 100 °F, la palabra Caliente aparecerá en la pantalla. Dado que estas funciones
producen mejores resultados si se inician cuando el horno esta frío, le recomendamos que
aguarde hasta que el horno se haya enfriado y Caliente desaparezca de la pantalla.
1. Presione Bread Proof (Entibiar pan para leudado).
2. Presione START/SET (INICIO/CONFIGURAR).
3. Presione OFF/CLEAR (APAGAR/BORRAR) en cualquier momento para desactivar la función
de entibiar pan para leudado.
NOTA
Utilice la posición 3 de la parrilla para el leudado del pan.
NE59M4320_DG68-00882A-01_MES.indd 29 2/16/2017 3:45:56 PM
30 Español
Funcionamiento del horno
Funcionamiento del horno
Cómo usar la función de mantener temperatura
Esta función mantendrá los alimentos calientes a una temperatura apta para servir por hasta
tres horas después de nalizada la cocción.
Después de 3 horas, la función apagará el horno automáticamente. Esta función puede
utilizarse sin combinar con otras operaciones de cocción o se puede congurar para que se
active después de una operación de cocción regida por el temporizador o de inicio retardado.
No debe usar esta función para recalentar alimentos fríos.
Cómo utilizar la función de mantener temperatura
1. Presione Keep Warm (Mantener temperatura).
2. Presione START/SET (INICIO/CONFIGURAR).
3. Presione OFF/CLEAR (APAGAR/BORRAR) en cualquier momento para desactivar esta
función.
Cómo programar el horno para que se active la función de mantener
temperatura a continuación de una cocción temporizada
1. Programe el horno para Timed cooking (Cocción con temporizador).
(Consulte la sección sobre la función de cocción con temporizador en la página 24.)
2. Presione Keep Warm (Mantener temperatura) antes de presionar START/SET (INICIO/
CONFIGURAR) para iniciar la cocción.
3. Presione OFF/CLEAR (APAGAR/BORRAR) en cualquier momento para desactivar esta
función.
Deshidratar
Deshidratar seca los alimentos o elimina la humedad de los alimentos a través de la circulación
de calor. Después de secar los alimentos, guárdelos en un lugar fresco y seco. Agregar jugo de
limón o ananá o espolvorear azúcar sobre las frutas ayuda a conservar su dulzura.
1. Presione Dehydrate (Deshidratar). La temperatura predeterminada es de 150 °F.
2. Ingrese la temperatura que desee en el teclado numérico. (100 °F - 175 °F)
3. Presione START/SET (INICIO/CONFIGURAR).
Categoría Posición de la parrilla Temperatura (˚F)
Vegetales o frutas 3 o 4 100-150
Carne 3 o 4 145-175
NOTA
El tiempo de secado depende del grado de humedad y el tamaño de los alimentos y de la
humedad en el aire.
No es necesario precalentar el horno.
NE59M4320_DG68-00882A-01_MES.indd 30 2/16/2017 3:45:56 PM
Español 31
Funcionamiento del horno
Uso de la función Shabat
(Para uso en el Shabat y otras fechas sagradas judías)
K
Para obtener asistencia adicional, pautas para el uso adecuado y una lista completa
de modelos con la función Shabat, visite la web en http:\\www.star-k.org.
Puede usar la función Shabat solo con horneado. La temperatura del horno se puede regular
más alta o más baja después de haber congurado la función Shabat. (La función de ajuste de
temperatura del horno debe utilizarse solamente durante fechas sagradas judías.) Sin embargo,
la pantalla no cambiará ni se producirán sonidos cuando se produzca un cambio.
Una vez que el horno se encuentra correctamente congurado para hornear con la función
Shabat activada, el horno permanecerá encendido continuamente hasta que se cancele esa
función. Esto anulará la función de ahorro de energía transcurridas 12 horas que viene
congurada de fábrica. Si la luz del horno es necesaria durante el Shabat, presione
antes de activar la función Shabat. Una vez que la luz del horno se encuentre encendida y se
encuentre activada la función Shabat, la luz del horno permanecerá encendida hasta que la
función Shabat sea desactivada. Si la luz del horno debe estar apagada, asegúrese de apagarla
antes de activar la función Shabat.
Cómo utilizar la función Shabat
1. Presione Bake (Hornear). La temperatura predeterminada es de 350 °F.
2. Ingrese la temperatura que desea, por ejemplo 375 °F, mediante el teclado numérico.
3. Presione START/SET (INICIO/CONFIGURAR). El indicador de temperatura comenzará a
variar una vez que la temperatura del horno alcance 175 °F.
4. Presione Bake (Hornear) y 1 a la vez durante 3 segundos. En la pantalla se verá SAb.
Una vez que SAb haya aparecido en la pantalla, el horno ya no emitirá señales sonoras
ni mostrará ningún cambio. Usted podrá cambiar la temperatura del horno una vez
comenzada la operación de hornear. Recuerde que, una vez activada la función Shabat, el
horno ya no emitirá señales sonoras ni mostrará ningún cambio.
5. Puede apagar el horno en cualquier momento presionando OFF/CLEAR (APAGAR/
BORRAR). Esto apagará el horno. Si quiere desactivar la función Shabat, mantenga
presionado Bake (Hornear) y 1 al mismo tiempo durante 3 segundos. La palabra Sab
desaparecerá de la pantalla.
No intente activar ninguna otra función de programa excepto Hornear mientras la
función Shabat está activa. ÚNICAMENTE las siguientes teclas funcionarán correctamente
con la función Shabat activada: NÚMERO, BAKE (HORNEAR), START/SET (INICIO/
CONFIGURAR) y OFF/CLEAR (APAGAR/BORRAR). NINGUNA DE LAS DEMÁS TECLAS deben
utilizarse una vez que se haya activado la función Shabat.
Puede cambiar la temperatura del horno, pero la pantalla no cambiará y los tonos no
sonarán cuando se produzca un cambio. (La función de ajuste de temperatura del horno
debe utilizarse solamente en fechas sagradas judías.) Después de cambiar la temperatura
mientras la unidad está en modo Shabat hay una demora de 15 segundos antes de que
la unidad reconozca el cambio.
Puede programar la función de tiempo de cocción antes de activar la función Shabat.
Si se produjera un corte o interrupción de electricidad, el horno se apagará. Cuando
vuelva la electricidad el horno no se encenderá automáticamente. Aparecerá SAb en
la pantalla de control del horno, pero el horno no funcionará. Los alimentos pueden
retirarse con seguridad del horno mientras está en el modo Shabat, sin embargo, el
horno no puede volver a encenderse hasta después del Shabat/fechas sagradas judías.
Después de la celebración del Shabat apague el modo Shabat. Mantenga presionados
simultáneamente BAKE (HORNEAR) y 1 durante al menos 3 segundos para apagar el
modo Shabat. El horno podrá entonces usarse con todas las funciones normales.
No abra la puerta del horno ni cambie la temperatura del horno durante alrededor
de 30 minutos después de haber iniciado el modo Shabat para permitir que el horno
alcance la temperatura jada. Observe que para obtener un mejor rendimiento,
el ventilador del horno funciona solamente cuando la temperatura del horno está
aumentando.
No use la cubierta cuando el horno está en modo Shabat.
NE59M4320_DG68-00882A-01_MES.indd 31 2/16/2017 3:45:56 PM
32 Español
Funcionamiento del horno
Funcionamiento del horno
Funciones adicionales
Ajuste del termostato
La temperatura dentro del horno ya ha sido regulada en la fábrica. Al principio, cuando utilice
el horno, asegúrese de seguir las indicaciones de tiempo y temperatura de las recetas. En caso
de que usted crea que la temperatura del horno es excesiva o insuciente, es posible ajustarla.
Antes de ajustar, pruebe una receta utilizando una regulación de temperatura más alta o más
baja que la recomendada. Los resultados de horneado de esa manera probablemente le sirvan
de guía para decidir la magnitud del ajuste requerido.
La temperatura del horno puede ajustarse ±35 °F (±19 °C).
Cómo ajustar la temperatura del horno
1. Presione Broil (Asar a la parrilla) y 1 a la vez durante 3 segundos.
En la pantalla aparece 0.
2. Ingrese el ajuste que desea, por ejemplo 20 °F, mediante el teclado numérico.
Se puede ajustar la temperatura a un nivel más bajo que el congurado en fábrica
presionando Broil (Asar a la parrilla).
3. Presione START/SET (INICIO/CONFIGURAR).
NOTA
Este ajuste no afectará la temperatura para asar a la parrilla ni la de auto-limpieza. El ajuste se
mantendrá en la memoria incluso después de un corte de electricidad.
Función de auto-conversión por convección
Cuando se utiliza la función de autoconversión, la función de autoconversión por convección
convertirá automáticamente las temperaturas normales ingresadas a las temperaturas
correspondientes para convección.
Si se encuentra activada esta función, en la pantalla se verá la temperatura real convertida
(reducida). Por ejemplo, si usted ingresa una temperatura de receta normal de 350 °F y
presiona START/SET (INICIO/CONFIGURAR), en la pantalla se verá la temperatura convertida de
325 °F.
Cómo desactivar o activar la función de auto-conversión
1. Presione Broil (Asar a la parrilla) y 3 a la vez durante 3 segundos.
En la pantalla se verá On (activada) o OFF (desactivada).
La conguración predeterminada es Con OFF (Conversión desactivada).
2. Presione 0 para seleccionar Con On (Conversión activada) o Con OFF (Conversión
desactivada).
Presionar 0 cambia el modo entre Con On (Conversión activada) y Con OFF (Conversión
desactivada).
3. Presione START/SET (INICIO/CONFIGURAR).
NE59M4320_DG68-00882A-01_MES.indd 32 2/16/2017 3:45:56 PM
Español 33
Funcionamiento del horno
Activar o desactivar las señales sonoras
Mediante esta función se pueden congurar los controles del horno para que funcionen
silenciosamente.
Cómo activar o desactivar el sonido
1. Presione Broil (Asar a la parrilla) y 6 a la vez durante 3 segundos.
La pantalla mostrará On (sonido activado) o OFF (sonido desactivado).
El ajuste predeterminado es Snd On (Sonido activado).
2. Presione 0 para seleccionar Snd On (Sonido activado) o Snd OFF (Sonido desactivado).
Presionar 0 cambia el modo entre Snd On (Sonido activado) y Snd OFF (Sonido
desactivado).
3. Presione START/SET (INICIO/CONFIGURAR).
Modo demostración
Esta opción es para ser usada por comercios minoristas para nes de exhibición únicamente.
(El elemento calentador no funciona).
Cómo activar o desactivar el modo demostración
1. Presione Broil (Asar a la parrilla) y 7.
2. Presionar 0 cambia el modo entre On (activado) y OFF (desactivado).
3. Presione START/SET (INICIO/CONFIGURAR).
Traba de controles
Esta función permite trabar los botones del panel táctil de modo que no puedan activarse
accidentalmente.
Cómo activar la función de traba de controles
1. Presione START/SET (INICIO/CONFIGURAR) por 3 segundos.
Loc y el icono de la cerradura aparecen en la pantalla al igual que la hora actual.
Se deben cancelar todas las funciones antes de poder activar la traba de controles.
Esta función está disponible cuando la temperatura del horno es inferior a 400 °F.
Cómo destrabar los controles
1. Presione START/SET (INICIO/CONFIGURAR) por 3 segundos.
Loc y el icono de bloqueo desaparecerán de la pantalla
NE59M4320_DG68-00882A-01_MES.indd 33 2/16/2017 3:45:56 PM
34 Español
Mantenimiento de su electrodoméstico
Mantenimiento de su electrodoméstico
Auto-limpieza
Este horno auto-limpiante utiliza altas temperaturas (mucho más altas que las
temperaturas de cocción) para eliminar por incineración los restos de grasa y
otros residuos o reducirlas a no polvo de ceniza que se puede limpiar con un
paño húmedo.
PRECAUCIÓN
Durante el ciclo de auto-limpieza, el exterior de la estufa puede volverse muy caliente al
tacto. No deje a niños pequeños sin vigilancia en la proximidad del electrodoméstico.
Algunas aves son muy sensibles a las emanaciones que se producen durante el ciclo de
auto-limpieza de cualquier estufa. Lleve las aves a otra habitación bien ventilada.
No revista con papel de aluminio las paredes del horno, parrillas, fondo o ninguna otra
parte de la estufa. Hacerlo podría tener como consecuencia una mala distribución del
calor, malos resultados de horneado y daños permanentes al interior del horno. El papel
de aluminio se derretirá y adherirá a la supercie interior del horno.
No fuerce la apertura de la puerta del horno. Tales maniobras pueden dañar el sistema
de traba automática de la puerta. Tenga precaución al abrir la puerta del horno cuando
se haya completado el ciclo de auto-limpieza. Tome una posición hacia un lado del horno
cuando abra la puerta para dejar salir el vapor o aire caliente. El horno aún se encontrará
MUY CALIENTE.
Antes de un ciclo de auto-limpieza
Fig. 1
Recomendamos habilitar una ventilación en su
cocina con una ventana abierta o mediante una
campana de ventilación o ventilador durante el
ciclo de auto-limpieza.
Retire del horno las parrillas, la asadera y su
accesorio, todos los recipientes de cocción y
todo el papel de aluminio.
Utilice una esponja o un paño para retirar la
suciedad del fondo del horno. (Fig. 1)
Las parrillas plateadas pueden soportar el ciclo
de auto-limpieza, pero se oscurecerán, perderán
lustre y se volverán difíciles de deslizar.
No limpie
manualmente la
junta selladora de la
puerta del horno.
La puerta se
puede limpiar
manualmente.
Fig. 2
Los residuos sobre el marco frontal de la estufa
y la parte que queda por fuera de la junta
selladora de la puerta deben ser limpiados
manualmente. Limpie estas áreas con agua
caliente, esponjas de lana de acero bien
enjabonadas o productos de limpieza tales
como Soft Scrub. Enjuague cuidadosamente con
agua limpia y seque las supercies.
No limpie la junta selladora. El material de bra
de vidrio de la junta de la puerta del horno no
resiste la abrasión. Es fundamental que esa
junta selladora permanezca intacta. Si usted
nota que se está desgastando o deshilachando,
reemplácela. (Fig. 2)
Asegúrese de que la cubierta de la bombilla de
la luz del horno se encuentre bien colocada y
que la luz del horno esté apagada.
NOTA
Quite las parrillas y los accesorios del horno antes
de activar el modo de auto-limpieza.
NE59M4320_DG68-00882A-01_MES.indd 34 2/16/2017 3:45:57 PM
Español 35
Mantenimiento de su electrodoméstico
Cómo hacer funcionar un ciclo de auto-limpieza
1. Seleccione la duración de la operación de auto-limpieza, por ejemplo: 3 horas.
Presione Self Clean (Auto-limpieza) una vez para un tiempo de limpieza de 3 horas, dos
veces para un tiempo de limpieza de 5 horas, o 3 veces para un tiempo de limpieza de
2 horas.
La conguración predeterminada es de 3 horas.
2. Inicie el ciclo de auto-limpieza. Presione START/SET (INICIO/CONFIGURAR). La traba de la
puerta del horno accionada por motor se cerrará automáticamente.
Le resultará imposible iniciar un ciclo de auto-limpieza si se encuentra activada la
función de traba de controles o si la temperatura del horno es demasiado elevada.
La puerta del horno se traba automáticamente. En la pantalla se verá el tiempo que
falta para completar la limpieza. La apertura de la puerta será imposible hasta que
la temperatura del horno disminuya hasta un nivel seguro.
La función de auto-limpieza no funcionará cuando el centro de calentamiento es
encendido.
3. Cuando el ciclo de auto-limpieza haya nalizado, la palabra Fin aparecerá en la pantalla y
la estufa emitirá una señal sonora 6 veces.
Cómo diferir el inicio del proceso de auto-limpieza
1. Presione Self Clean (Auto-limpieza). Presione el tiempo de auto-limpieza deseado
presionando Self Clean (Auto-limpieza).
2. Presione Delay Start (Inicio retardado).
3. Ingrese la hora a la que desea que inicie el ciclo de limpieza.
4. Presione START/SET (INICIO/CONFIGURAR). En la pantalla se verá Delay (Inicio retardado),
Self clean (Auto-limpieza) y el icono de bloqueo. La traba de la puerta del horno
accionada por motor se cerrará automáticamente.
5. El ciclo de auto-limpieza se activará automáticamente a la hora jada.
Como apagar la función de auto-limpieza
Es posible que se vea en la necesidad de detener o interrumpir un ciclo de auto-limpieza
debido a humo dentro del horno.
1. Presione OFF/CLEAR (APAGAR/BORRAR).
2. La puerta solamente se podrá abrir cuando la temperatura del horno se haya reducido lo
suciente, lo cual demora aproximadamente una hora.
Después de un ciclo de auto-limpieza
Es posible que note una cierta cantidad de ceniza blanca dentro del horno. Límpiela con
un paño húmedo una vez que el horno se haya enfriado. (Si quedan manchas blancas,
quítelas con una esponja de lana de acero bien enjabonada y enjuague a fondo con una
mezcla de vinagre y agua).
Si el horno no ha quedado limpio después de un ciclo, repita el ciclo.
No se puede programar el horno para cocción hasta que su temperatura se haya reducido
lo suciente como para permitir que la puerta se destrabe.
NE59M4320_DG68-00882A-01_MES.indd 35 2/16/2017 3:45:57 PM
36 Español
Mantenimiento de su electrodoméstico
Mantenimiento de su electrodoméstico
Limpieza con vapor
Cómo programar el horno para limpieza con vapor
Para limpieza liviana, la función de limpieza con vapor ahorra tiempo y energía. Si se requiere
un trabajo de limpieza más intenso, use la función de auto-limpieza.
1. Retire del horno todos los accesorios.
2. Vierta aproximadamente 10 onzas (300 ml)
de agua en el fondo del horno vacío y cierre
la puerta del horno. Utilice solamente agua
normal, no agua destilada.
3. Presione Steam Clean (Limpieza con vapor).
4. Presione START/SET (INICIO/CONFIGURAR).
Cuando se haya completado la operación,
la pantalla parpadeará y se oirá una señal
sonora.
5. Presione OFF/CLEAR (APAGAR/BORRAR).
6. Limpie el interior del horno.
Después de un ciclo de limpieza al vapor
quedará una signicativa cantidad de agua
en la parte inferior del horno. Retire el agua
residual utilizando una esponja o un paño
suave seco.
Al realizar la limpieza al vapor, utilice exactamente 10 onzas de agua, ya que así se
obtienen los mejores resultados.
NOTA
Si presiona Steam Clean (Limpieza con vapor) cuando la temperatura del horno se encuentra
por encima de los 100 °F, aparecerá la palabra Hot (caliente) en la pantalla. Dado que
estas funciones producen mejores resultados si se inician cuando el horno esta frío, le
recomendamos que aguarde hasta que el horno se haya enfriado y Caliente desaparezca de la
pantalla.
Después de un ciclo de limpieza al vapor
Tenga cuidado al abrir la puerta antes de que nalice el procedimiento de limpieza al
vapor. El agua en la base está caliente.
Abra la puerta del horno y retire el agua remanente con una esponja. No permita que el
agua residual permanezca en el horno por más tiempo que el indispensable. Limpie el
horno y séquelo con un paño suave. No olvide limpiar debajo de la junta selladora de la
puerta del horno.
Para limpiar el interior del horno, utilice una esponja empapada en detergente, un
cepillo suave, o un estropajo de nylon. Quite los residuos tenazmente adheridos con un
estropajo de nylon. Para quitar los depósitos calcáreos puede utilizar un paño empapado
en vinagre.
Si el horno aún está sucio, puede repetir el proceso una vez que el horno se haya
enfriado.
Para el caso de residuos pesados, tales como la grasa remanente después de asar, le
recomendamos que frote detergente sobre el residuo antes de activar la función de
limpieza al vapor.
Después de limpiar, deje la puerta del horno entornada en un ángulo de 15° para que la
supercie interior esmaltada pueda secarse completamente.
Cuidado y limpieza del horno
ADVERTENCIA
Asegúrese de que todos los controles estén APAGADOS y todas las supercies FRÍAS
antes de limpiar cualquier parte de la estufa.
Si su estufa es removida para limpieza, reparación o cualquier
motivo, asegúrese de que el dispositivo anti inclinación se vuelva a
encastrar correctamente cuando se vuelve a colocar la estufa. Si no
encastra el dispositivo anti inclinación, la estufa podría inclinarse y
producir lesiones graves.
NE59M4320_DG68-00882A-01_MES.indd 36 2/16/2017 3:45:57 PM
Español 37
Mantenimiento de su electrodoméstico
Abertura de ventilación del horno
Abertura de
ventilación
del horno
La abertura de ventilación se encuentra
ubicada por sobre la unidad de supercie
trasera derecha.
Esta área podría calentarse durante el uso
del horno.
Es normal que salga vapor por esta abertura.
La abertura de ventilación es importante
para la correcta circulación del aire. Nunca
tapone esta abertura de ventilación.
Limpieza de las partes pintadas y las terminaciones decorativas
Para su limpieza general, utilice un paño con agua jabonosa caliente.
Para residuos más resistentes o grasa acumulada, aplique un detergente líquido
directamente sobre el área y espere de 30 a 60 minutos. Limpie con un paño húmedo y
luego seque. No utilice limpiadores abrasivos sobre ninguna de estas supercies. Pueden
causar rayaduras.
Limpieza de supercies de acero inoxidable
1. Agite bien el envase del producto limpiador de electrodomésticos de acero inoxidable o
de líquido de pulir.
2. Coloque una pequeña cantidad de producto limpiador de electrodomésticos de acero
inoxidable o de líquido de pulir sobre un paño húmedo o sobre una toalla de papel
húmeda.
3. Limpie un área pequeña, frotando en la dirección del grano del acero inoxidable, si fuese
el caso.
4. Seque y lustre con una toalla de papel seca y limpia o un paño húmedo.
5. Repita en la medida de lo necesario.
NOTA
No use una esponja de lana de acero. Rayará la supercie.
Si anteriormente el electrodoméstico fue limpiado utilizando un producto a base de
aceite mineral, lave la supercie con líquido lavavajilla y agua antes de utilizar producto
limpiador de electrodomésticos de acero inoxidable o de líquido de pulir.
Parrillas del horno
Si las parrillas se dejan en el horno durante un ciclo de auto-limpieza, su color virará a
tonos azulados y se volverán opacas. Una vez nalizado el ciclo de auto-limpieza y que
se haya enfriado el horno, frote las barras laterales de las parrillas con un papel encerado
o con un paño humedecido con una pequeña cantidad de aceite. Esto permitirá que las
parrillas se deslicen más fácilmente en sus carriles.
Puerta del horno
No limpie
manualmente la
junta selladora de
la puerta del horno.
La puerta se
puede limpiar
manualmente.
Utilice agua y jabón para limpiar a fondo
la parte superior, los lados y el frente de la
puerta del horno. Enjuague bien. Se puede
utilizar un líquido limpiavidrios sobre la cara
exterior de la ventana de la puerta del horno.
NO sumerja la puerta en agua. NO rocíe ni
permita que agua ni líquido limpiavidrios
penetre en los oricios de ventilación de
la puerta. NO utilice productos para limpiar
hornos, polvos de pulir, ni ningún material
de limpieza fuertemente abrasivo sobre el
exterior de la puerta del horno.
NO limpie la junta selladora de la puerta del
horno. La junta selladora de la puerta del
horno está confeccionada con un material
tejido que es esencial para un cierre bien
sellado. Se debe tener cuidado de no frotar,
dañar o retirar la junta.
NE59M4320_DG68-00882A-01_MES.indd 37 2/16/2017 3:45:57 PM
38 Español
Mantenimiento de su electrodoméstico
Mantenimiento de su electrodoméstico
Cuidado y limpieza de la cubierta de vidrio
Limpieza en el uso normal diario
Use solo un producto de limpieza para cubiertas vitrocerámicas. Otras cremas podrían resultar
menos efectivas.
Seguir estos pasos le permitirá mantener y proteger la supercie de su cubierta de vidrio.
1. Antes de utilizar la cubierta por primera vez, límpiela con un producto de limpieza para
cubiertas vitrocerámicas.
Esto ayuda a proteger la cubierta y facilita la limpieza.
2. Utilizar diariamente un producto de limpieza para cubiertas vitrocerámicas ayudará a que
la cubierta mantenga la apariencia de nueva.
3. Agite bien la crema de limpieza. Aplique unas pocas gotas del producto de limpieza
directamente sobre la cubierta.
4. Utilice una toalla de papel o una almohadilla para limpiar cubiertas vitrocerámicas para
limpiar toda la supercie de la cubierta.
5. Utilice un paño seco o una toalla de papel para quitar todos los residuos de la limpieza.
No es necesario enjuagar.
ADVERTENCIA
Se podrían producir DAÑOS a la supercie de vidrio si se utilizaran almohadillas o estropajos
distintos de los recomendados.
Cómo quitar los residuos quemados
1. Espere que la cubierta se enfríe.
2. Esparza unas pocas gotas de limpiador para
cubiertas vitrocerámicas sobre toda la zona
de residuos quemados.
3. Utilice el paño de limpieza para supercies
de cocción cerámicas y frote la zona de los
residuos aplicando la presión necesaria.
4. Si queda algún residuo, repita los pasos
arriba enumerados según resulte necesario.
5. Para protección adicional, después de
haber quitado todo el residuo, lustre toda la
supercie con el producto de limpieza para
la cubierta cerámica y una toalla de papel.
NE59M4320_DG68-00882A-01_MES.indd 38 2/16/2017 3:45:58 PM
Español 39
Mantenimiento de su electrodoméstico
Cómo quitar gruesas capas de residuos quemados y adheridos
1. Espere que la cubierta se enfríe.
2. Utilice una rasqueta de navaja de un solo
lo a un ángulo de 45° sobre la supercie de
vidrio y raspe la suciedad.
Será necesario aplicar presión para poder
quitar los residuos.
3. Después de raspar con la rasqueta de navaja,
esparza unas pocas gotas de limpiador para
cubiertas vitrocerámicas sobre toda la zona
de residuos quemados. Utilice el paño de
limpieza para quitar los residuos que queden.
(No raspe la junta selladora).
4. Para protección adicional, después de
haber quitado todo el residuo, lustre toda la
supercie con el producto de limpieza para
la cubierta y una toalla de papel.
Cómo quitar marcas de metal y arañazos
1. Tenga cuidado de no deslizar cacerolas y sartenes sobre su cubierta. Esto dejará marcas
en la supercie de la cubierta. Puede quitar estas marcas utilizando o un limpiador
para cubiertas vitrocerámicas con un paño de limpieza especíco para limpiar estas
supercies.
2. Si se dejan hirviendo hasta secarse los recipientes de limpieza someramente revestidos
con aluminio o cobre, el revestimiento puede dejar manchas de color sobre la cubierta.
Estas manchas de color se deben quitar inmediatamente o se pueden volver permanentes.
ADVERTENCIA
Controle cuidadosamente los fondos de los recipientes de cocción para asegurarse de que
estén libres de rugosidades que puedan rayar la cubierta.
Limpieza de la junta selladora de la cubierta
Para limpiar la junta selladora a lo largo de los
bordes del vidrio, deje un paño mojado reposando
contra ella por unos minutos y luego limpie con
un producto no abrasivo.
Potenciales daños permanentes a la supercie de vidrio
Los derrames de materiales azucarados (tales como jaleas, caramelo, almíbares) o
plásticos fundidos pueden causar picaduras en la supercie de la cubierta. Esta situación
no está cubierta por la garantía. El derrame debe limpiarse mientras permanezca caliente.
Tenga especial cuidado al quitar sustancias calientes. Consulte la sección siguiente.
Si utiliza una rasqueta, asegúrese de que sea nueva y que su navaja mantenga buen lo.
No utilice una navaja sin lo o con mordeduras.
Limpieza de derrames azucarados y plástico fundido
1. Apague todas las unidades de supercie. Quite todos los recipientes de cocción calientes.
2. Usando un guante aislante, utilice una rasqueta de navaja de un solo lo para mover la
sustancia derramada a una zona de la cubierta que no se encuentre caliente. Quite la
sustancia derramada con toallas de papel.
3. El remanente del derrame debe dejarse hasta que la supercie de cocción se haya
enfriado.
4. No vuelva a utilizar las unidades de supercie hasta que todo el residuo haya sido
eliminado completamente.
NOTA
Si ya se han producido picaduras o hendiduras en la supercie de vidrio, la cubierta de vidrio
deberá ser reemplazada. En tal caso, será necesario llamar al servicio de reparaciones.
NE59M4320_DG68-00882A-01_MES.indd 39 2/16/2017 3:45:58 PM
40 Español
Mantenimiento de su electrodoméstico
Mantenimiento de su electrodoméstico
Cómo retirar y volver a colocar la puerta del horno
Cómo retirar la puerta
PRECAUCIÓN
La puerta es muy pesada. Tenga cuidado al retirarla y levantarla.
No levante la puerta por la manija.
Desconecte la electricidad antes de retirar la puerta.
Traba de la
bisagra
Posición trabada Posición destrabada
1. Abra la puerta por completo.
2. Jale las trabas de las bisagras hacia abajo, hacia el marco de la puerta hasta la posición
destrabada.
aprox. 5°
Fig. 1
3. Sujete rmemente ambos lados de la puerta
en su extremo superior.
4. Cierre la puerta hasta la posición de
remoción, que es a aproximadamente
5 grados de la posición vertical (Fig. 1).
Fig. 2
5. Levante la puerta y hale hacia afuera hasta
que el brazo de la bisagra esté fuera de la
ranura (Fig. 2).
Cómo volver a colocar la puerta
Brazo de la
bisagra
Borde
inferior de
la ranura
Muesca
1. Sujete rmemente ambos lados de la puerta en su extremo superior.
2. Con la puerta en el mismo ángulo que en la posición para retirar, deslice la muesca del
brazo de la bisagra hasta que encaje en el borde inferior de la ranura para la bisagra.
La muesca en el brazo de la bisagra debe quedar completamente inserta en la parte
inferior de la ranura.
NE59M4320_DG68-00882A-01_MES.indd 40 2/16/2017 3:45:59 PM
Español 41
Mantenimiento de su electrodoméstico
Traba de la bisagra
Posición trabadaPosición destrabada
3. Abra la puerta por completo. Si la puerta no se abre completamente, la muesca no se
encuentra correctamente insertada en el borde inferior de la ranura.
4. Empuje las trabas de bisagra hacia arriba contra el marco frontal de la cavidad del horno
hasta que queden en la posición trabada.
5. Cierre la puerta del horno.
Cómo retirar y volver a colocar el cajón de almacenamiento
Gancho
Cómo retirar el cajón de almacenamiento
1. Retire el cajón hacia afuera hasta que se
detenga.
2. Incline el frontal del cajón y extráigalo hasta
que se detenga.
3. Levante el cajón y extráigalo.
Cómo volver a colocar el cajón de
almacenamiento
1. Ponga el lado izquierdo del cajón sobre el
gancho izquierdo y el lado derecho sobre el
gancho derecho.
2. Empuje el cajón hasta que se detenga.
3. Incline y levante el cajón.
4. Empuje el cajón hacia adentro.
Recambio de la luz del horno
La luz del horno es una bombilla para electrodomésticos estándar de 40 watts. Se encenderá al
abrirse la puerta del horno. Cuando la puerta del horno se encuentre cerrada, presione la tecla
para encenderla o apagarla. No funcionará durante el ciclo de auto-limpieza.
Bombilla
Retirar Volver a colocar
Cubierta de vidrio de la bombilla
1. Asegúrese de que el horno y la bombilla se
encuentren fríos.
2. Desenchufe la estufa o desconecte la
corriente.
3. Para retirar la cubierta de vidrio de la
bombilla en la parte trasera del horno, gírela
en sentido contrario a las agujas del reloj.
4. Gire la bombilla en sentido contrario a las
agujas del reloj para retirarla de su casquillo.
5. Inserte una bombilla nueva para
electrodomésticos de 40 watts y, luego,
gírela hacia la derecha para ajustarla. Vuelva
a colocar la cubierta de la bombilla girando
hacia la derecha.
6. Enchufe la estufa o vuelva a conectar la
electricidad.
PRECAUCIÓN
Antes de cambiar la bombilla de la luz de su
horno, desconecte la alimentación de electricidad
a la estufa en el fusible principal o en el panel
del disyuntor. Asegúrese de que el horno y la
bombilla se encuentren fríos.
NE59M4320_DG68-00882A-01_MES.indd 41 2/16/2017 3:45:59 PM
42 Español
Resolución de problemas
Resolución de problemas
Resolución de problemas
Samsung hace grandes esfuerzos para asegurar que usted no experimente problemas con su nueva estufa
eléctrica. Si se encuentra con problemas inesperados, como primera medida busque la solución en la
siguiente tabla. Si, luego de intentar la solución sugerida, aún experimenta problemas, llame a Samsung al
número 1-800-SAMSUNG (1-800-726-7864).
Instalación
Problema Causa posible Solución
La estufa está desnivelada. El electrodoméstico fue instalado
incorrectamente.
Coloque la parrilla del horno
en el centro del horno.
Coloque un nivel sobre la
parrilla. Ajuste las patas de
nivelación en la base de la
estufa hasta que la parrilla del
horno quede nivelada.
Asegúrese de que el piso
esté nivelado y sea lo
sucientemente fuerte y
estable como para soportar
la estufa.
El piso se encuentra vencido,
combado, hundido o inclinado.
Contáctese con un carpintero para
corregir esta situación.
Son los gabinetes de cocina los que
están desalineados y hacen que la
estufa parezca desnivelada.
Asegúrese de que los gabinetes se
encuentren en escuadra y dejan
suciente lugar para la instalación.
Es necesario acceder
al electrodoméstico
para efectuarle servicio
de mantenimiento o
reparación y resulta difícil
de mover.
Los gabinetes de cocina no
están en escuadra o están
construidos demasiado cerca del
electrodoméstico.
Comuníquese con un constructor o
instalador para posibilitar el acceso
al electrodoméstico.
La alfombra interere con el
movimiento de la estufa.
Despeje suciente espacio para que
la estufa pueda ser levantada por
encima de la alfombra.
PANTALLA DE CONTROL
Problema Causa posible Solución
La pantalla queda en
blanco.
Puede haberse quemado un fusible
en su casa o haberse disparado el
disyuntor.
Reemplace el fusible o reinicie el
disyuntor.
La pantalla destella. Hubo un corte de energía eléctrica. Reajuste el reloj.
CUBIERTA
Problema Causa posible Solución
Las unidades de supercie
no mantienen un hervor
continuo o no cocinan con
la rapidez esperable.
Puede estar usando recipientes de
cocción inadecuados.
Utilice recipientes de fondo plano
y cuyo diámetro se corresponda
con la unidad de supercie
seleccionada.
En algunas áreas, el potencial
eléctrico (voltaje) puede estar
demasiado bajo.
Cubra el recipiente con una tapa
hasta que se alcance la temperatura
deseada.
Las unidades de supercie
no se encienden.
Puede haberse quemado un fusible
en su casa o haberse disparado el
disyuntor.
Reemplace el fusible o reinicie el
disyuntor.
Los controles de la supercie de
cocción están incorrectamente
congurados.
Controle que se encuentre
congurado el control correcto para
la unidad de supercie en uso.
Zonas con alteraciones de
color en la cubierta.
Se omitió limpiar alimentos
derramados.
Remítase a la sección sobre cuidado
y limpieza de la cubierta de vidrio,
en las páginas 38-39.
La supercie está caliente y el
modelo se caracteriza por una
cubierta de color claro.
Esto es normal. El color de la
supercie puede aparecer alterado
cuando está caliente. Esto es
transitorio y desaparecerá a medida
que el vidrio se enfríe.
NE59M4320_DG68-00882A-01_MES.indd 42 2/16/2017 3:45:59 PM
Español 43
Resolución de problemas
Problema Causa posible Solución
La unidad de supercie
alterna frecuentemente
entre encendido y
apagado.
La unidad de supercie
deja de estar al rojo vivo
cuando se cambia a una
regulación más baja.
El elemento pasará por ciclos
de encendido y apagado para
mantener la regulación de energía.
Este funcionamiento es normal y no
se debe a una falla del sistema. Use
el horno como siempre.
Rayaduras o abrasiones
en la supercie de la
cubierta.
La limpieza de la cubierta se es
realizando incorrectamente.
Las rayaduras son imposibles de
quitar. Por efectos de la limpieza,
las rayaduras muy pequeñas se
volverán menos visibles con el
transcurrir del tiempo. Use una
crema para limpiar la supercie
vitrocerámica. No use sustancias
químicas ni productos abrasivos.
Estos productos pueden dañar la
supercie del electrodoméstico.
Se usaron sobre la cubierta
recipientes de cocción con fondos
rugosos, o se depositaron partículas
gruesas y abrasivas (por ejemplo,
sal o arena) entre los recipientes y
la supercie de la cubierta.
Para evitar rayaduras, utilice
los procedimientos de limpieza
recomendados. Asegúrese de que
los fondos de los recipientes de
cocción estén limpios antes de
usarlos. Utilice recipientes de
fondos lisos.
Se ha deslizado algún utensilio
de cocina sobre la supercie de
cocción.
Problema Causa posible Solución
Pintas o vetas pardas. Ocurrieron derrames que fueron
cocinados hasta adherirse a la
supercie.
Espere hasta que la supercie
se enfríe. Luego, utilice una
rasqueta para eliminar las
impurezas. Utilice la rasqueta
de navaja para quitar la
suciedad.
Consulte la sección sobre
cuidado y limpieza de la
cubierta de vidrio, en las
páginas 38-39.
Zonas con alteración de
color con brillo metálico.
Depósitos minerales originados
en el agua o los alimentos
permanecieron sobre la supercie
de la cubierta.
Quítelos utilizando una crema
de limpieza para cubiertas
vitrocerámicas.
Utilice recipientes de cocción
con fondos limpios y secos.
Limpie la cubierta con un
limpiador para cerámica
regularmente cada semana.
Se oyen ruidos como
crujidos o suaves
estallidos.
Estos son los ruidos que emite
el metal al calentarse y enfriarse
durante las funciones de cocción y
auto-limpieza.
Este funcionamiento es normal y no
se debe a una falla del sistema. Use
el horno como siempre.
NE59M4320_DG68-00882A-01_MES.indd 43 2/16/2017 3:46:00 PM
44 Español
Resolución de problemas
Resolución de problemas
HORNO
Problema Causa posible Solución
El horno no se enciende. La estufa no se encuentra bien
enchufada al tomacorriente.
Asegúrese de que el enchufe
se encuentre insertado en un
tomacorriente alimentado con
corriente y bien conectado a tierra.
Puede haberse quemado un fusible
en su casa o haberse disparado el
disyuntor.
Reemplace el fusible o reinicie el
disyuntor.
Los controles del horno se han
congurado incorrectamente.
Vea el capítulo donde se describe la
operación del horno.
El horno está demasiado caliente. Espere a que el horno se enfríe.
El servicio técnico no completó la
conexión de cables.
Solicite servicio técnico.
Hay un corte de energía en su
localidad.
Controle si se encienden las luces
de su casa. De ser necesario, llame
a su compañía de electricidad local.
No se enciende la luz del
horno.
La bombilla está oja o fallada. Ajuste o reemplace la bombilla.
El interruptor de la luz está roto. Solicite servicio técnico.
Problema Causa posible Solución
El horno emite demasiado
humo cuando se asa a la
parrilla.
El control no fue regulado
correctamente.
Consulte la sección sobre la
regulación de los controles del
horno.
La carne fue colocada demasiado
próxima al elemento radiante.
Cambie la posición de la parrilla
para dejar el espacio adecuado
entre la carne y el elemento
radiante. Si desea sellar la carne,
precaliente el elemento radiante.
La carne no fue preparada
correctamente.
Quite el exceso de grasa de la
carne. Corte y retire los bordes
grasos que podrían retorcerse,
dejando intacto la carne magra.
Hay acumulación de grasa sobre las
supercies del horno.
Es necesario limpiar con
regularidad si se asa a la parrilla
con frecuencia.
Los alimentos no se
hornean o asan como es
debido.
Los controles del horno se han
congurado incorrectamente.
Vea el capítulo donde se describe la
operación del horno.
La parrilla del horno fue colocada
en una posición incorrecta o no se
encuentra nivelada.
Vea la sección sobre el uso de las
parrillas del horno en las páginas
25-26.
Se están utilizando recipientes de
cocción no adecuados o de tamaño
incorrecto.
El sensor del horno requiere ajuste. Vea la sección sobre cómo ajustar
el termostato, en la página 32.
NE59M4320_DG68-00882A-01_MES.indd 44 2/16/2017 3:46:00 PM
Español 45
Resolución de problemas
Problema Causa posible Solución
Los alimentos no se asan a
la parrilla correctamente.
El tamaño de la porción puede no
ser el adecuado.
Consulte la guía de cocción para el
tamaño de las porciones y vuelva a
intentarlo.
La parrilla fue colocada en una
posición incorrecta.
Vea la guía de recomendaciones
para asar a la parrilla, en la página
29.
El recipiente no es adecuado para
asar a la parrilla.
Utilice utensilios de cocción
adecuados.
En algunas áreas, el potencial
eléctrico (voltaje) puede estar
demasiado bajo.
Precaliente durante
10 minutos el elemento de
asado a la parrilla.
Vea la guía de
recomendaciones para asar a
la parrilla, en la página 29.
El horno está a
temperatura demasiado
alta o demasiado baja.
El sensor del horno requiere ajuste. Vea la sección sobre cómo ajustar
el termostato, en la página 32.
El horno no ejecuta el
proceso de auto-limpieza.
La temperatura del horno es
demasiado alta como para iniciar
una operación de auto-limpieza.
Deje que la estufa se enfríe y,
luego, restablezca los controles.
Los controles del horno se han
congurado incorrectamente.
Vea la sección sobre auto-limpieza,
en la página 34.
No se puede iniciar un ciclo de
auto-limpieza si ha activado la
función de traba del horno o
si algún elemento radiante de
supercie se encuentra encendido.
Desactive la traba del horno
(consulte la página 33).
Asegúrese de que todos los
elementos superiores estén
apagados.
Problema Causa posible Solución
Humo excesivo durante un
ciclo de auto-limpieza.
El horno se encuentra demasiado
sucio.
Presione OVEN OFF (APAGAR
HORNO). Abra las ventanas para
que el humo salga del ambiente.
Aguarde hasta que el ciclo de auto-
limpieza se cancele. Limpie toda la
suciedad excesiva y luego inicie el
ciclo de auto-limpieza.
Después de un ciclo de
auto-limpieza la puerta del
horno, no se abre.
El horno está demasiado caliente. Espere a que el horno se enfríe.
Cumplido un ciclo de auto-
limpieza, el horno aún no
está limpio.
Los controles del horno se han
congurado incorrectamente.
Vea la sección sobre auto-limpieza,
en la página 34.
El horno tenía suciedad pesada. Limpie los derrames pesados antes
de iniciar el ciclo de auto-limpieza.
Cuando el horno está muy sucio,
puede ser necesario repetir la
auto-limpieza o darle una duración
mayor.
Sale vapor por la abertura
de ventilación.
Cuando se usa la función de
convección, es normal ver
salir vapor por la abertura de
ventilación.
Este funcionamiento es normal y no
se debe a una falla del sistema. Use
el horno como siempre.
La cantidad de vapor visible
aumenta cuando se usan más
parrillas o se cocina mayor cantidad
de alimento.
Sale olor a quemado o a
aceite de la abertura de
ventilación.
Esto es normal cuando el horno
es nuevo y desaparecerá con el
tiempo.
Para acelerar este proceso,
programe un ciclo de auto-
limpieza de por lo menos
3 horas.
Vea la sección sobre auto-
limpieza, en la página 34.
NE59M4320_DG68-00882A-01_MES.indd 45 2/16/2017 3:46:00 PM
46 Español
Resolución de problemas
Resolución de problemas
Problema Causa posible Solución
Olor fuerte. Las primeras veces que se usa el
horno, es normal que emane olor
del material aislante que envuelve
al horno.
Opere el horno en el ajuste de
horneado a 400 °F durante una
hora.
Ruido del ventilador. Un ventilador de convección
puede encenderse y apagarse
automáticamente.
Este funcionamiento es normal y no
se debe a una falla del sistema. Use
el horno como siempre.
Resulta difícil deslizar las
parrillas del horno.
Las parrillas plateadas quedaron
dentro del horno durante un ciclo
de auto-limpieza.
Aplique una pequeña cantidad de
aceite vegetal sobre una toalla de
papel y frote con él los lados de la
parrilla.
CAJÓN
Problema Causa posible Solución
El cajón no se desliza con
suavidad o se arrastra con
fricción.
El cajón se encuentra desalineado. Jale el cajón hacia afuera
completamente y empújelo
totalmente hacia adentro.
Ver página 41.
El cajón está sobrecargado o la
carga está desbalanceada.
Reduzca el peso. Redistribuya el
contenido de los cajones.
Códigos de información
HORNO
Problema Causa posible Solución
C-20 El sensor del horno está
abierto cuando el horno está
funcionando.
Presione OVEN OFF (APAGAR
HORNO) y vuelva a encender el
horno. Si el problema persiste,
desconecte toda alimentación
eléctrica a la estufa durante
por lo menos 30 segundos y
luego reconecte la alimentación
eléctrica. Si esto no soluciona el
problema, llame al servicio de
reparaciones.
Hay un cortocircuito en el sensor
del horno cuando el horno está
funcionando.
C-21 Este código se muestra si
la temperatura interna es
anormalmente alta.
C-d1 Este código se muestra si el
bloqueo de la puerta está mal
colocado.
C-d0 Este código se muestra si en
la tecla de control hay un
cortocircuito durante 1 minuto.
Presione OVEN OFF (APAGAR
HORNO) y vuelva a encender el
horno. Si el problema persiste,
desconecte toda alimentación
eléctrica a la estufa durante
por lo menos 30 segundos y
luego reconecte la alimentación
eléctrica. Si esto no soluciona el
problema, llame al servicio de
reparaciones.
C-30 El sensor PCB está abierto cuando
el horno está funcionando.
El sensor PCB está
cortocircuitado cuando el horno
está funcionando.
C-31 Este código se muestra si
la temperatura de PCB es
anormalmente alta.
Solicite servicio técnico.
NE59M4320_DG68-00882A-01_MES.indd 46 2/16/2017 3:46:00 PM
Español 47
Garantía (EE.UU.)
Garantía (EE.UU.)
NO LA DESECHE. ESTA HOJA REEMPLAZA LA PÁGINA DE GARANTÍA EN LA
GUÍA DE USO Y MANTENIMIENTO
ESTUFA ELÉCTRICA SAMSUNG
GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL
El presente producto de la marca SAMSUNG, tal como lo provee y distribuye
SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) y lo entrega como nuevo,
en su empaque de cartón original al comprador o consumidor original, está
garantizado por SAMSUNG contra defectos de fabricación de los materiales y la
mano de obra durante el período limitado de la garantía de:
Un (1) año para las piezas y la mano de obra, un (1) año para las piezas de la Garantía
Para la cubierta de vidrio y la hornalla radiante
La presente garantía limitada comienza en la fecha original de compra y es válida únicamente
para productos comprados y usados en los Estados Unidos. Para recibir el servicio técnico
de la garantía, el comprador debe comunicarse con SAMSUNG a n de que se determine el
problema y los procedimientos del servicio. El servicio técnico de la garantía solo puede
ser prestado por un centro de servicio técnico autorizado de SAMSUNG. Se debe presentar
la factura de compra original como prueba de compra a SAMSUNG o al servicio técnico
autorizado de SAMSUNG. Samsung brindará servicio técnico a domicilio sin cargo durante
el período de garantía, sujeto a disponibilidad, dentro del territorio contiguo de los Estados
Unidos. El servicio técnico a domicilio no se encuentra disponible en todas las áreas. Como
condición para que se preste este servicio a domicilio, el producto debe encontrarse libre
de obstrucciones y accesible para el agente de servicio. Si el servicio no está disponible,
Samsung podrá optar por brindar el servicio de transporte del producto de ida y vuelta
al centro de servicio. SAMSUNG reparará o reemplazará el producto a nuestra discreción
y sin cargo tal como se establece en la presente garantía, con piezas o productos nuevos
o reacondicionados si se comprueba que es defectuoso durante el período limitado de la
garantía especicado anteriormente. Todas las piezas y los productos reemplazados pasan
a ser propiedad de SAMSUNG y deben ser devueltos a SAMSUNG. Las piezas y los productos
reemplazados asumen la garantía original que resta, o noventa (90) días, el período que sea el
más prolongado.
La presente garantía limitada cubre defectos de fabricación de los materiales y la mano de
obra encontrados durante el uso normal y doméstico de este producto y no será válida para
lo siguiente: daños que ocurran durante el envío; entrega e instalación; aplicaciones y usos
para los cuales el presente producto no fue destinado; producto o números de serie alterados;
daño cosmético o acabado exterior; accidentes, abuso, descuido, incendio, inundación, caída
de rayos, u otros casos fortuitos o de fuerza mayor; uso de productos, equipo, sistemas,
utilidades, servicios, piezas, suministros, accesorios, aplicaciones, instalaciones, reparaciones,
cableado externo o conectores no provistos ni autorizados por SAMSUNG que dañen este
producto o que acarreen problemas en el servicio; voltaje de la línea eléctrica incorrecto,
uctuaciones y sobretensión; ajustes del cliente e incumplimiento de lo establecido en el
manual de instrucciones sobre instrucciones de utilización, mantenimiento y ambientales que
están cubiertas y recomendadas en el manual de instrucciones; desmontaje y reinstalación del
producto; problemas causados por plagas; recalentamiento o exceso de cocción causado por
el usuario. Esta garantía limitada no cubre casos de corriente, voltaje o alimentación eléctrica
incorrectos, bombillas de luz, fusibles y cableado en la casa, el costo de las llamadas al servicio
técnico para solicitar instrucciones, ni la corrección de errores de instalación. Tampoco están
cubiertos los daños a la cubierta de vidrio causados por el uso de productos y elementos
de limpieza distintos de los productos y almohadillas recomendadas, daños a la cubierta de
vidrio causados por derrames endurecidos de sustancias azucaradas o plásticos fundidos que
no hubiesen sido limpiados de acuerdo con las instrucciones incluidas en la guía de uso y
cuidados. SAMSUNG no garantiza el funcionamiento ininterrumpido o sin errores del producto.
NE59M4320_DG68-00882A-01_MES.indd 47 2/16/2017 3:46:00 PM
48 Español
Garantía (CANADÁ)
SALVO LO ESTABLECIDO EN ESTE DOCUMENTO, NO EXISTEN GARANTÍAS RESPECTO DE ESTE
PRODUCTO NI EXPRESAS NI TÁCITAS Y SAMSUNG DESCONOCE Y RECHAZA TODA GARANTÍA
INCLUIDAS, AUNQUE NO TAXATIVAMENTE ENUMERADAS, TODA GARANTÍA TÁCITA DE
COMERCIABILIDAD, INFRACCIÓN O APTITUD PARA UN PROPÓSITO ESPECIAL. NINGUNA OTRA
GARANTÍA OTORGADA POR PERSONA, COMPAÑÍA O CORPORACIÓN ALGUNA CON RESPECTO
AL PRESENTE PRODUCTO REVESTIRÁ CARÁCTER VINCULANTE PARA SAMSUNG. SAMSUNG
NO SERÁ RESPONSABLE POR PÉRDIDA DE INGRESOS O LUCRO CESANTE, IMPOSIBILIDAD
DE GENERAR AHORROS U OBTENER OTROS BENEFICIOS, O CUALQUIER DAÑO DERIVADO DE
CIRCUNSTANCIAS ESPECIALES, DAÑO IMPREVISTO O DERIVADO CAUSADO POR EL USO, USO
INCORRECTO, O INCAPACIDAD PARA USAR EL PRESENTE PRODUCTO, INDEPENDIENTEMENTE
DE LA TEORÍA LEGAL EN QUE SE FUNDE EL RECLAMO Y AUN CUANDO SE LE HAYA
NOTIFICADO A SAMSUNG DE LA POSIBILIDAD DE TALES DAÑOS. NINGÚN RESARCIMIENTO
DE NINGUNA ÍNDOLE CONTRA SAMSUNG SUPERARÁ EL MONTO DEL PRECIO DE COMPRA
DEL PRODUCTO VENDIDO POR SAMSUNG Y CAUSANTE DEL PRESUNTO DAÑO. SIN LIMITAR
LO PRECEDENTE, EL COMPRADOR ASUME TODO EL RIESGO Y LA RESPONSABILIDAD
POR PÉRDIDA, DAÑO O LESIÓN AL COMPRADOR Y A LOS BIENES DEL COMPRADOR Y A
TERCEROS Y A SUS BIENES DERIVADOS DEL USO, USO INCORRECTO O INCAPACIDAD PARA
USAR EL PRESENTE PRODUCTO. LA PRESENTE GARANTÍA LIMITADA NO SE EXTENDERÁ A
NINGUNA PERSONA DISTINTA DEL COMPRADOR ORIGINAL DEL PRESENTE PRODUCTO, ES
INTRANSFERIBLE Y ESTABLECE SU EXCLUSIVA REPARACIÓN.
Algunos territorios o provincias pueden permitir, o no, las limitaciones en cuanto al plazo de
una garantía implícita, o la exclusión o limitación de daños imprevistos o derivados, por lo
tanto las limitaciones o exclusiones antedichas pueden no aplicarse en su caso. Esta garantía
le otorga derechos legales especícos, y además puede tener otros derechos que varían según
el Estado en el que se encuentre. Las piezas sustituibles por el usuario se pueden enviar al
cliente para la reparación de la unidad. Si es necesario, se puede enviar a un técnico para que
efectúe el servicio.
Para recibir un servicio técnico de garantía, comuníquese con SAMSUNG a:
Samsung Electronics America, Inc.
85 Challenger Road Ridgeeld Park, NJ 07660
1-800-SAMSUNG (726-7864) y www.samsung.com/us/support
Garantía (CANADÁ)
NO LA DESECHE. ESTA HOJA REEMPLAZA LA PÁGINA DE GARANTÍA EN LA
GUÍA DE USO Y MANTENIMIENTO
ESTUFA ELÉCTRICA SAMSUNG
GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL
El presente producto de la marca SAMSUNG, tal como lo provee y distribuye
SAMSUNG ELECTRONICS CANADA, INC. (SAMSUNG) y lo entrega como nuevo,
en su empaque de cartón original al comprador o consumidor original, está
garantizado por SAMSUNG contra defectos de fabricación de los materiales y la
mano de obra durante el período limitado de la garantía de:
Un (1) año para las piezas y la mano de obra, un (1) año para las piezas de la Garantía
Para la cubierta de vidrio y la hornalla radiante
La presente garantía limitada comienza en la fecha original de compra y es válida únicamente
para productos comprados y usados en CANADÁ. Para recibir el servicio técnico de la garantía,
el comprador debe comunicarse con SAMSUNG a n de que se determine el problema y los
procedimientos del servicio. El servicio técnico de la garantía solo puede ser prestado por un
centro de servicio técnico autorizado de SAMSUNG. Se debe presentar la factura de compra
original como prueba de compra a SAMSUNG o al servicio técnico autorizado de SAMSUNG.
Samsung brindará servicio técnico a domicilio sin cargo durante el período de garantía, sujeto
a disponibilidad, dentro del territorio contiguo de CANADÁ. El servicio técnico a domicilio no
se encuentra disponible en todas las áreas. Como condición para que se preste este servicio
a domicilio, el producto debe encontrarse libre de obstrucciones y accesible para el agente
de servicio. Si el servicio no está disponible, Samsung podrá optar por brindar el servicio de
transporte del producto de ida y vuelta al centro de servicio.
NE59M4320_DG68-00882A-01_MES.indd 48 2/16/2017 3:46:00 PM
Español 49
Garantía (CANADÁ)
SAMSUNG reparará o reemplazará el producto a nuestra discreción y sin cargo tal como
se establece en la presente garantía, con piezas o productos nuevos o reacondicionados si
se comprueba que es defectuoso durante el período limitado de la garantía especicado
anteriormente. Todas las piezas y los productos reemplazados pasan a ser propiedad de
SAMSUNG y deben ser devueltos a SAMSUNG. Las piezas y los productos reemplazados
asumen la garantía original que resta, o noventa (90) días, el período que sea el más
prolongado. La presente garantía limitada cubre defectos de fabricación de los materiales
y la mano de obra encontrados durante el uso normal y doméstico de este producto y no
será válida para lo siguiente: daños que ocurran durante el envío; entrega e instalación;
aplicaciones y usos para los cuales el presente producto no fue destinado; producto o
números de serie alterados; daño cosmético o acabado exterior; accidentes, abuso, descuido,
incendio, inundación, caída de rayos, u otros casos fortuitos o de fuerza mayor; uso de
productos, equipo, sistemas, utilidades, servicios, piezas, suministros, accesorios, aplicaciones,
instalaciones, reparaciones, cableado externo o conectores no provistos ni autorizados por
SAMSUNG que dañen este producto o que acarreen problemas en el servicio; voltaje de la línea
eléctrica incorrecto, uctuaciones y sobretensión; ajustes del cliente e incumplimiento de lo
establecido en el manual de instrucciones sobre instrucciones de utilización, mantenimiento y
ambientales que están cubiertas y recomendadas en el manual de instrucciones; desmontaje
y reinstalación del producto; problemas causados por plagas; recalentamiento o exceso de
cocción causado por el usuario. Esta garantía limitada no cubre casos de corriente, voltaje o
alimentación eléctrica incorrectos, bombillas de luz, fusibles y cableado en la casa, el costo
de las llamadas al servicio técnico para solicitar instrucciones, ni la corrección de errores de
instalación. Tampoco están cubiertos los daños a la cubierta de vidrio causados por el uso de
productos y elementos de limpieza distintos de los productos y almohadillas recomendadas,
daños a la cubierta de vidrio causados por derrames endurecidos de sustancias azucaradas o
plásticos fundidos que no hubiesen sido limpiados de acuerdo con las instrucciones incluidas
en la guía de uso y cuidados. SAMSUNG no garantiza el funcionamiento ininterrumpido o sin
errores del producto.
SALVO LO ESTABLECIDO EN ESTE DOCUMENTO, NO EXISTEN GARANTÍAS RESPECTO DE ESTE
PRODUCTO NI EXPRESAS NI TÁCITAS Y SAMSUNG DESCONOCE Y RECHAZA TODA GARANTÍA
INCLUIDAS, AUNQUE NO TAXATIVAMENTE ENUMERADAS, TODA GARANTÍA TÁCITA DE
COMERCIABILIDAD, INFRACCIÓN O APTITUD PARA UN PROPÓSITO ESPECIAL. NINGUNA OTRA
GARANTÍA OTORGADA POR PERSONA, COMPAÑÍA O CORPORACIÓN ALGUNA CON RESPECTO
AL PRESENTE PRODUCTO REVESTIRÁ CARÁCTER VINCULANTE PARA SAMSUNG. SAMSUNG
NO SERÁ RESPONSABLE POR PÉRDIDA DE INGRESOS O LUCRO CESANTE, IMPOSIBILIDAD
DE GENERAR AHORROS U OBTENER OTROS BENEFICIOS, O CUALQUIER DAÑO DERIVADO DE
CIRCUNSTANCIAS ESPECIALES, DAÑO IMPREVISTO O DERIVADO CAUSADO POR EL USO, USO
INCORRECTO, O INCAPACIDAD PARA USAR EL PRESENTE PRODUCTO, INDEPENDIENTEMENTE
DE LA TEORÍA LEGAL EN QUE SE FUNDE EL RECLAMO Y AUN CUANDO SE LE HAYA
NOTIFICADO A SAMSUNG DE LA POSIBILIDAD DE TALES DAÑOS. NINGÚN RESARCIMIENTO
DE NINGUNA ÍNDOLE CONTRA SAMSUNG SUPERARÁ EL MONTO DEL PRECIO DE COMPRA
DEL PRODUCTO VENDIDO POR SAMSUNG Y CAUSANTE DEL PRESUNTO DAÑO. SIN LIMITAR
LO PRECEDENTE, EL COMPRADOR ASUME TODO EL RIESGO Y LA RESPONSABILIDAD
POR PÉRDIDA, DAÑO O LESIÓN AL COMPRADOR Y A LOS BIENES DEL COMPRADOR Y A
TERCEROS Y A SUS BIENES DERIVADOS DEL USO, USO INCORRECTO O INCAPACIDAD PARA
USAR EL PRESENTE PRODUCTO. LA PRESENTE GARANTÍA LIMITADA NO SE EXTENDERÁ A
NINGUNA PERSONA DISTINTA DEL COMPRADOR ORIGINAL DEL PRESENTE PRODUCTO, ES
INTRANSFERIBLE Y ESTABLECE SU EXCLUSIVA REPARACIÓN.
Algunos Estados no permiten limitaciones en cuanto al plazo de una garantía implícita, o
la exclusión o limitación de daños imprevistos o derivados, por lo tanto las limitaciones o
exclusiones antedichas pueden no aplicarse en su caso. Esta garantía le otorga derechos
legales especícos, y además puede tener otros derechos que varían según el Estado en el que
se encuentre.
Para recibir un servicio técnico de garantía, comuníquese con SAMSUNG a:
Samsung Electronics Canada Inc.
2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada
1-800-SAMSUNG (726-7864) y www.samsung.com/ca/support (English)
www.samsung.com/ca_fr/support (French)
NE59M4320_DG68-00882A-01_MES.indd 49 2/16/2017 3:46:00 PM
Notas
NE59M4320_DG68-00882A-01_MES.indd 50 2/16/2017 3:46:00 PM
Notas
NE59M4320_DG68-00882A-01_MES.indd 51 2/16/2017 3:46:00 PM
Veuillez noter que la garantie Samsung n'inclut pas les déplacements du service après-vente pour expliquer le fonctionnement de l'appareil, corriger une installation non correcte ou exécuter des
travaux de nettoyage ou d'entretien réguliers.
UNE QUESTION ? UN COMMENTAIRE ?
PAYS N° DE TÉLÉPHONE SITE INTERNET
U.S.A
Consumer Electronics
1-800-SAMSUNG (726-7864) www.samsung.com/us/support
CANADA 1-800-SAMSUNG (726-7864)
www.samsung.com/ca/support (English)
www.samsung.com/ca_fr/support (French)
DG68-00882A-01
Scannez le code QR* ou rendez-vous sur
le site www.samsung.com/spsn pour voir
nos vidéos et démonstrations en direct
d'utilisation.
* Requiert l'installation d'un lecteur sur
votre smartphone
NE59M4320_DG68-00882A-01_CFR.indd 52 2/16/2017 3:46:25 PM
1 / 1

Samsung NE59M4320SB/AA-00 El manual del propietario

Categoría
Cocinas
Tipo
El manual del propietario
Este manual también es adecuado para

En otros idiomas