Yamaha AT-800 El manual del propietario

Marca: Yamaha

Modelo: AT-800

Categoría: Accesorios de pantalla plana

Tipo: El manual del propietario

Yamaha AT-800: Conecta este dispositivo a la pared para instalar tu unidad de audio de manera segura y evitar caídas. Viene con tornillos de seguridad para mayor estabilidad. Es fácil de instalar y está diseñado para soportar el peso de la unidad de audio y brindar una experiencia de audio segura y placentera.

English Français Deutsch Svenska Italiano Español Nederlands

中文 한국어

Русский

ATTACHMENT

ATTACHE

AT-800

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Bruksanvisning

Manuale di istruzioni

Manual de instrucciones

Gebruiksaanwijzing

Инструкция по эксплуатации

使用说明书

사용 설명서

JTG

DIMENSIONS

ABMESSUNGEN

MATTSKISSER

DIMENSIONI

DIMENSIONES

AFMETINGEN

ГАБАРИТЫ

各个部分的尺寸

크기

200 mm (7-7/8")

51 mm

(2")

51 mm

(2")

22 mm

(7/8")

61.5 mm

(2-3/8")

90 mm

(3-1/2")

227 mm (8-7/8")

215.5 mm

(8-1/2")

183 mm (7-1/4")

308 mm (12-1/8")

410 mm (16-1/8")

(ISX-800)

1 En

English

ATTACHMENT

AT-800

Owner’s Manual

Thank you for selecting this Yamaha product. Be sure to read this manual thoroughly before using this product.

After you have read this manual, retain it for future reference.

* For information on the dimensions of the Attachment, please refer to page i (back of the cover page).

SAFETY INSTRUCTIONS

 Always follow the instructions set forth in this manual when installing the audio unit using this

Attachment.

Insufficiently secure installation or insecure Attachment could cause the audio unit to fall, resulting in personal injury.

• Install the audio unit so that it will withstand extended use and will not fall due to vibrations caused by earthquakes or children.

• To ensure safety, all screws must be tightened securely.

• Never hang from the audio unit or the Attachment.

 Once the audio unit is installed, safety checks should be conducted on a regular basis.

If the audio unit is used over an extended period of time, screws can become loose and the installation can become

weaker due to the passage of time, vibrations, etc.

 Yamaha is not responsible for any accident or personal injury caused by a falling audio unit, nor for

damage to a wall caused by inappropriate wall conditions or inadequate installation.

 Make sure to leave adequate ventilation space around the unit to allow heat generated by the audio

unit to dissipate.

Failure to provide adequate space around the unit could cause the audio unit to overheat internally, resulting in a fire.

 Install the audio unit in a location where the unit’s buttons will be easily accessible. Leave enough

space around the unit so that you can easily insert a CD or connect a USB device, or iPod, etc. to the

unit.

iPod

USB

2 En

Make sure the package contains the following items.

Make sure that you leave adequate ventilation space around the unit and follow the instructions below. Be sure to use the

specified mounting screws for installation to prevent the audio unit from falling. Illustrations for each step use the ISX-800.

1 Use the template on the back cover to mark screw positions on the wall with a pin.

Remove the template, and then attach commercially-available tapping screws

(ø6

(1/4")) in the marked positions.

To prevent the wall surface from being damaged, drill pilot holes, then attach the screws.

Notes

• Choose a secure wall or beam to fasten the screws. Do not install them into walls made of weak material that can easily come off,

such as mortar or plywood wall panels. Loose screws could cause the audio unit to fall, resulting in personal injury.

• Do not use screws shorter than the specified length, nails, or double-sided adhesive tape. Otherwise, the audio unit may fall due

to wear or vibration, possibly resulting in personal injury.

PACKAGE CONTENTS

ASSEMBLING PROCEDURE

Attaching the screws to the wall

Attachment (AT-800)

Have the following items ready in addition:

• Commercially available tapping screws (x4)

(

6 mm (1/4") , 31 mm (1-1/4") or more in

length, 7 mm (1/4") or more in screw head

diameter)

• M4 screws that came with the audio unit (x4)

(If the screws are being used to mount the

audio unit on a dedicated stand, remove the

screws.)

• Phillips(+) screwdriver

(Do not use electric tools.)

Weight: 1.3 kg (2.9 lbs)

Safety wire (x2)

Length: 300 mm

(11-3/4")

Washer (x2)

(for M6, 16 mm (5/8")

of outer diameter)

7 mm (1/4") or more

25 mm (1") or more

200 mm (7-7/8")

6mm

(1/4")

3 En

English

1 Remove the rear cover and terminal cover from the audio unit.

If the audio unit has been mounted on a dedicated

stand, remove the stand. Also, remove the power

cable, antenna and/or external devices.

Four M4 screws that you remove from the stand

will be used in Step

Note

Spread a soft cloth under the audio unit to avoid any

damage to the audio unit or work surface.

For more information, refer to the Assembly Guide

for the ISX-800.

2 Connect the power cable, antenna and/or external devices.

Pass the cables through a hole in the bottom of the Attachment, then connect them to the audio unit.

After connecting the cables, replace the terminal cover.

3 Install the Attachment on the audio unit.

Attach four M4 screws that came with the audio

unit (for attaching the stand to the audio unit).

Do not tighten the screws using excessive force.

Do not use electric tools.

Notes

• Be careful not to pinch the cables between the

Attachment and audio unit.

• Make sure that you identify the screws for the rear

cover and the screws for the stand correctly.

• If you tighten the screws on a slant, the screw

threads in the audio unit might break.

Installing the Attachment on the audio unit

The rear cover and the screws you

removed from the rear cover will not

be used to install the Attachment.

Keep them in a safe place.

Terminal cover

Rear cover

4 En

1 Attach the safety wires to the Attachment.

Attach the safety wires as

shown in the figure on the

right.

2 Installing the audio unit on the wall.

Hang the audio unit by hooking the mounting

holes on the upper part of the Attachment onto

the screws in the wall.

3 Attach the safety wires to the wall.

Pass the screws (commercially

available) through the washers

(supplied), and then through the loops

on the end of the safety wires, and

tighten the screws into the wall to

secure the safety wires while

removing any slack of the wires.

Notes

• Make sure that the screws are strong

enough to bear the weight of the audio

unit and the Attachment in case they

fall.

• Choose a secure wall or beam to fasten

the screws.

Notes

• After installation is complete, make sure that the audio unit is securely affixed. Yamaha is not responsible for any accident

caused by inappropriate wall conditions or inadequate installation.

• Be sure to secure the cables so that they will not be caught by feet or hands, possibly causing the audio unit to fall.

Installing the audio unit on the wall

Slip one end through

the loop at the other

end

Safety wire

Screw

(

ø6 mm;

commercially

available)

Washer

(supplied)

Printed in China WZ39290

200 mm (7-7/8")

Yamaha AT-800 El manual del propietario

Marca: Yamaha

Modelo: AT-800

Categoría: Accesorios de pantalla plana

Tipo: El manual del propietario

Descargar PDF

informe

en otros idiomas

français: Yamaha AT-800 Le manuel du propriétaire
italiano: Yamaha AT-800 Manuale del proprietario
English: Yamaha AT-800 Owner's manual
Deutsch: Yamaha AT-800 Bedienungsanleitung
русский: Yamaha AT-800 Инструкция по применению
Nederlands: Yamaha AT-800 de handleiding
português: Yamaha AT-800 Manual do proprietário
dansk: Yamaha AT-800 Brugervejledning
svenska: Yamaha AT-800 Bruksanvisning
Türkçe: Yamaha AT-800 El kitabı
suomi: Yamaha AT-800 Omistajan opas

Yamaha AT-800 El manual del propietario

Yamaha AT-800 El manual del propietario

en otros idiomas

Artículos relacionados