Yamaha VL-1 El manual del propietario

Marca: Yamaha

Modelo: VL-1

Categoría: Pianos digitales

Tipo: El manual del propietario

Este manual también es adecuado para

Owner’s Manual 2

Feature Reference

Contents

■ 3: Feedback Delay . . . . . . . . . . . . . . . . . . . . . . 53

• Mono Delay . . . . . . . . . . . . . . . . . . . . . . . 53

• L,R Delay . . . . . . . . . . . . . . . . . . . . . . . . 55

• L,C,R Delay . . . . . . . . . . . . . . . . . . . . . . 57

■ 4:Reverberation . . . . . . . . . . . . . . . . . . . . . . . . 60

• Hall1, Hall2, Room1, Room2, Studio,

Plate, Space, Reverse . . . . . . . . . . . . . . . 61

Element Controller . . . . . . . . . . . . . . . . . . . . . 64

■ 1: Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

■ 2: Embouchure . . . . . . . . . . . . . . . . . . . . . . . . 66

■ 3: Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

■ 4: Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

■ 5: Tonguing . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

■ 6: Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . 71

■ 7: Scream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

■ 8: Breath Noise . . . . . . . . . . . . . . . . . . . . . . . . 73

■ 9: Growl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

■ 10: Throat Formant . . . . . . . . . . . . . . . . . . . . . 75

■ 11: Dynamic Filter . . . . . . . . . . . . . . . . . . . . . 77

■ 12; Harmonic Enhancer . . . . . . . . . . . . . . . . . 78

■ 13: Damping . . . . . . . . . . . . . . . . . . . . . . . . . . 80

■ 14: Absorption . . . . . . . . . . . . . . . . . . . . . . . . . 81

Element Miscellaneous . . . . . . . . . . . . . . . . . 84

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

■ 2: Breath Noise . . . . . . . . . . . . . . . . . . . . . . . . 86

• 2-1: Breath Noise Level Key Scaling . . 88

• 2-2: Breath Noise HPF Key Scaling . . . 89

• 2-3: Breath Noise LPF Key Scaling . . . . 90

■ 3: Throat Formant . . . . . . . . . . . . . . . . . . . . . . 91

• 3-1: Throat Formant Pitch Key Scaling . 93

• 3-2: Throat Formant Amount Key

Scaling . . . . . . . . . . . . . . . . . . . . . . . 94

• 3-3: Throat Formant Intensity Key

Scaling . . . . . . . . . . . . . . . . . . . . . . . 95

• 3-4: Throat Formant HPF Key Scaling . 96

• 3-5: Throat Formant LPF Key Scaling . 97

■ 4: Mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

• 4-1: Mixing Driver Output Key Scaling 100

• 4-2: Mixing Pipe/String Output Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 101

• 4-3: Mixing Tap Output Key Scaling . 102

• 4-4: Mixing Tap Location Key Scaling 103

About the Manuals . . . . . . . . . . . . . . . . . . . . . . 4

■ The Getting Started Manual . . . . . . . . . . . . . . 4

■ The Feature Reference Manual (this manual) . 5

■ Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General Operation

■ The Three Main Modes . . . . . . . . . . . . . . . . . . . 8

■ Finding Functions & Parameters . . . . . . . . . . . 9

■ Other Navigation Aids . . . . . . . . . . . . . . . . . . 11

■ Selecting & Editing Parameters . . . . . . . . . . . 12

Play Mode

■ The Main Play Mode Display . . . . . . . . . . . . . 14

■ Voice Selection . . . . . . . . . . . . . . . . . . . . . . . . 15

■ Controller Views . . . . . . . . . . . . . . . . . . . . . . . 17

■ Quick Editing In the Play Mode . . . . . . . . . . . 19

Edit Mode

■ The Voice Number Buttons In the Edit Mode 22

■ The Edit Compare Function . . . . . . . . . . . . . . 24

■ The Copy Function . . . . . . . . . . . . . . . . . . . . . 25

■ Storing Edited Data . . . . . . . . . . . . . . . . . . . . . 28

Initial Edit Page . . . . . . . . . . . . . . . . . . . . . . . . 30

Common Miscellanous . . . . . . . . . . . . . . . . . 34

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

■ 2: Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 36

■ 3: Element Pitch . . . . . . . . . . . . . . . . . . . . . . . 37

■ 4: Element Level & Pan . . . . . . . . . . . . . . . . . 38

■ 5: Portamento . . . . . . . . . . . . . . . . . . . . . . . . . 40

■ 6: Micro Tuning . . . . . . . . . . . . . . . . . . . . . . . 42

■ 7: Continuous Slider . . . . . . . . . . . . . . . . . . . . 43

Common Effect . . . . . . . . . . . . . . . . . . . . . . . . 44

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

■ 2: Modulation Effect . . . . . . . . . . . . . . . . . . . . 46

• Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

• Pitch Change . . . . . . . . . . . . . . . . . . . . . . 49

• Distortion . . . . . . . . . . . . . . . . . . . . . . . . . 51

Feature Reference

■ 5: Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . 104

• 5-1: Total Amplitude Level Key Scaling104

Element Modifier . . . . . . . . . . . . . . . . . . . . . 106

■ 1: Harmonic Enhancer . . . . . . . . . . . . . . . . . 107

•1-1: Harmonic Enhancer HPF Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 110

•1-2: Harmonic Enhancer Overdrive Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 111

• 1-3: Harmonic Enhancer Carrier Level

Key Scaling . . . . . . . . . . . . . . . . . . 112

• 1-4: Harmonic Enhancer Modulator

Index Key Scaling . . . . . . . . . . . . . 113

• 1-5: Harmonic Enhancer Balance Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 114

■ 2: Dynamic Filter . . . . . . . . . . . . . . . . . . . . . 115

• 2-1: Dynamic Filter Cutoff Key Scaling 117

• 2-2: Dynamic Filter Resonance Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 118

■ 3: Equalizer Auxiliary . . . . . . . . . . . . . . . . . . 119

• 3-1: Equalizer Auxiliary HPF Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 120

• 3-2: Equalizer Auxiliary LPF Key

Scaling . . . . . . . . . . . . . . . . . . . . . . 121

■ 4: Equlizer Band . . . . . . . . . . . . . . . . . . . . . . 122

■ 5: Impulse Expander & Resonator Setting . . 123

■ 6: Impulse Expander . . . . . . . . . . . . . . . . . . . 125

■ 7: Resonator . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Element Envelope . . . . . . . . . . . . . . . . . . . . . 128

■ 1: Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

■ 2: Embouchure & Pitch . . . . . . . . . . . . . . . . . 130

• 2-1: Embouchure & Pitch Hold Time

Key Scaling . . . . . . . . . . . . . . . . . . 132

• 2-2: Embouchure & Pitch Initial Level

Key Scaling . . . . . . . . . . . . . . . . . . 133

• 2-3: Embouchure & Pitch Decay Rate

Key Scaling . . . . . . . . . . . . . . . . . . 134

■ 3: Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

• 3-1: Vibrato Delay Time Key Scaling . 137

• 3-2: Vibrato Attack Rate Key Scaling . 138

• 3-3: Vibrato Depth Key Scaling . . . . . . 139

• 3-4: Vibrato Speed Key Scaling . . . . . . 140

■ 4: Growl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

• 4-1: Growl Speed Key Scaling . . . . . . . 142

■ 5: Amplitude & Filter . . . . . . . . . . . . . . . . . . 143

• 5-1: Amplitude & Filter Attack Rate

Key Scaling . . . . . . . . . . . . . . . . . . 146

• 5-2: Amplitude & Filter Attack 1 Level

Key Scaling . . . . . . . . . . . . . . . . . . 147

• 5-3: Amplitude & Filter Decay Rate

Key Scaling . . . . . . . . . . . . . . . . . . 148

• 5-4: Amplitude & Filter Sustain Level

Key Scaling . . . . . . . . . . . . . . . . . . 149

• 5-5: Amplitude & Filter Release Rate

Key Scaling . . . . . . . . . . . . . . . . . . 150

Utility Mode

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

MIDI Bulk Dump . . . . . . . . . . . . . . . . . . . . . . 160

Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Edit Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . 172

Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174

Appendix

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 178

Error Messages . . . . . . . . . . . . . . . . . . . . . . . 180

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 184

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Feature Reference

About the Manuals

The VL1 comes with two manuals — Getting Started and Feature

Reference. If you’re just starting out with the VL1 we urge you to begin

with the Getting Started manual since it describes basic concepts and

procedures that are essential to proper operation of the VL1.

The Getting Started Manual

The Getting Started manual contains seven chapters that take you through

essential information and procedures you will need to know to become familiar

with your VL1:

1. VL1 Basics [≥ Page 8]

Basic concepts you’ll need to understand in order to get the

most out of the VL1.

2. The Controls & Connectors [≥ Page 16]

Brief descriptions of the VL1 controls and connectors, and their

functions.

3. Setting Up [≥ Page 22]

System connections, powering up, playing the demo, calibrating

the Breath Controller, and loading the pre-programmed voices.

4. Voice Selection [≥ Page 34]

Several ways to select and play the VL1’s 128 voices.

5. The Controllers [≥ Page 38]

The VL1 controllers and how they can be assigned and edited

for optimum control.

6. Mixing & The Modifiers [≥ Page 48]

Customizing the sound to suit your own personal needs.

7. Effects [≥ Page 58]

An overview of the built-in digital effects that you can use to

add depth and ambience to the VL1 sound.

We recommend that you go through the chapters in sequence and actually

try out the various operations described. Once you’ve gone through the entire

Getting Started manual in this way, you should be familiar enough with the VL1

to need only the VL1 Feature Reference manual in future.

Feature Reference

The Feature Reference Manual (this manual)

The Feature Reference manual is the “nuts and bolts” reference for

the VL1, individually describing its many functions in detail. The Feature

Reference manual is divided into five main sections, each describing the

various functions within a particular VL1 edit or utility mode.

1. General Operation [≥ Page 7]

2. Play Mode [≥ Page 13]

3. Edit Mode [≥ Page 21]

4. Utility Mode [≥ Page 151]

5. Appendix [≥ Page 177]

Once you have become familiar with the way the VL1 works by

going through the Getting Started manual, you should only need to refer

to the Feature Reference manual from time to time to get details on func-

tions you’ve never used before, or refresh your memory about functions

that you don’t use very often.

Each section of the Feature Reference manual has its own table of

contents, so you should be able to locate any particular function quickly

and easily. Functions and references can also be located by referring to the

index at the back of the manual.

Conventions

The following conventions are used through the VL1 manuals to

avoid confusion and make the text easier to read.

Buttons & Controls

Button and control names used on the VL1 panel appear in the text

in capital letters within a border: “the [ button”, for example.

Parameter Names

Parameter names and other labels which appear on the VL1 display

are printed in the courier typeface for easier identification: for

example, “adjust the “Balance” parameter as required”.

Parameter Ranges

An ellipsis is used to indicate a range of parameter values: e.g. “0

… 127”. This minimizes the confusion sometimes caused by the use

of a hyphen or dash for this purpose.

General Operation

The VL1 makes operation as easy as possible

by providing a consistent, logical control interface via

which its many functions and parameters can be

accessed and edited. Once you become familiar with

the system, operation should be smooth, efficient, and

easy.

● The Three Main Modes . . . . . . . . . . . . . 8

● Finding Functions & Parameters . . . . . 9

● Other Navigation Aids . . . . . . . . . . . . . 11

● Selecting & Editing Parameters . . . . . 12

Feature Reference

●

General Operation

The Three Main Modes

The VL1 has three main modes: PLAY, EDIT, and UTILITY. Each of these modes

can be directly accessed by pressing the P, E, or U button, respectively.

The PLAY mode is the one you use to select and play the VL1 voices.

The PLAY mode also includes several “Controller Views” that allow you

to check controller assignments, the status of several important

performance parameters, and the continuous slider assignments.

≥

Pages 13 through 19.

All voice editing functions are accessed via the EDIT mode: controller

assignments, mixing, modifiers, effects, and more.

≥

Pages 21 through 150.

The UTILITY mode includes a range of functions that affect overall

operation of the VL1 rather than individual voices. For example: master

tuning, MIDI settings, disk operations, etc.

≥

Pages 151 through 175.

PLAY

EDIT

UTILITY

Feature Reference

●

General Operation

Finding Functions & Parameters

To facilitate access to the many functions provided, the EDIT and UTILITY mode

functions are organized into logical groups arranged in a hierarchical structure (the PLAY

mode is simple enough that it doesn’t require this type of structure). The basic structure

of the EDIT mode, for example, looks like this:

EDIT MODE

ELEMENT

EFFECT

CONTROLLER

MODIFIER

ENVELOPE

COMMON

MISCELLANEOUS

Here you can see that the EDIT mode functions are divided into two main groups:

COMMON and ELEMENT, and that these are further sub-divided into related groups of

functions. The COMMON EFFECT group, for example, includes all the effect parameters

(flange, reverb, etc.) that apply to the entire voice. Here’s how you would access the

reverb parameters, starting from the PLAY mode:

●

Example: Locate the Effect Reverb Parameters

1. Press E

Pressing the E button from the PLAY or UTILITY mode will normally take

you to the initial EDIT display page (if the current voice has already been edited but not

stored, you will automatically return to the last EDIT mode page that was selected).

2. Press ¡ (“Com”)

Since you want the effect functions, which are in the common group, press the ¡

function button (immediately below “Com” on the display).

Feature Reference

●

General Operation

3. If Necessary, Press ™ (“Efct”)

If the miscellaneous directory is showing (in this case “Misc” above the ¡ button

will be highlighted), press the ™ button below “Efct” on the display to select the

effect directory.

4. Move the Cursor To “4:Reverberation” and Press [

Use the cursor buttons (or the - and = buttons, or the data dial)

to move the cursor to “4:Reverberation” and press the [ button. This will

take you to the first page of reverb parameters.

NOTES ■ Notice that the top line of the display shows the “path” to the current

level or function: “

EDIT/COM/EFFECT/REVERBERATION

”.

This example illustrates the two methods used to move downward through the EDIT

mode levels: 1) press the appropriate function button and 2) move the cursor to the

desired selection and press [.

From any point within the structure you can move upward toward the topmost level

(in this case the initial EDIT mode display) by pressing the ] button. You move up

one level each time the ] button is pressed, until the topmost level is reached.

To exit from the EDIT mode itself you must press either the P or U

button, depending on the mode you want to switch to. You can exit from the EDIT mode

at any level by doing this, and you will be returned automatically to the same display

page the next time you press the E button as long as the voice being edited is not

stored or a new voices is not selected.

Feature Reference

●

General Operation

Other Navigation Aids

In addition to the standard procedures described in the previous section, the VL1

sometimes provides additional help in moving between related functions via the function

buttons.

In this example display page from the ELEMENT CONTROLLER group, “Bpag”

(back page) and “Fpag” (forward page) appear above the § and ¶ function buttons.

In this case these buttons can be used to move forward and backward through the entire

list of controller functions so you don’t have to move up to the function directory and

then down to the next function every time you want to select a different element control-

ler page.

Also note the “Para” (Parameter) abbreviation above the • button. This enables

you to go directly to the parameters related to the current page: in this case the vibrato

parameters.

From here you can go back to the vibrato controller page by pressing the •

function button again (note that it is now labelled “Ctrl”), or to the vibrato key scaling

parameters by pressing ¶, below “KSC” on the display.

Another variation appears in the COMMON EFFECT parameter displays. In most

cases the number of parameters available for each effect exceeds the capacity of the

display, so the ¡ and ™ function buttons are used to scroll up and down the parameter

list — note the “>” and “<” arrows above the buttons in the display.

Feature Reference

●

General Operation

Selecting & Editing Parameters

Once you’ve locate the display page that contains the parameter(s) you want to edit,

simply use the cursor buttons to move the cursor to the parameter, and then use the data

dial or the = and - buttons to set the parameter as required. The data dial is ideal

for quickly covering a large range of settings, while the = and - buttons are best

for small stepwise changes.

Play Mode

The primary function of the PLAY mode is to

allow you to select and play voices. The VL1 play

mode additionally offers a range of controller views

that let you check controller assignments, and simple

“quick edit” capability. Select the PLAY mode from

either the EDIT or UTILITY mode by pressing the

P button.

● The Main Play Mode Display . . . . . . . 14

● Voice Selection . . . . . . . . . . . . . . . . . . 15

● Controller Views . . . . . . . . . . . . . . . . . 17

● Quick Editing In the Play Mode . . . . . 19

Feature Reference

●

Play Mode

The Main Play Mode Display

When you select the PLAY mode by pressing the P button, the main PLAY

mode display will appear. This display includes a considerable amount of information in

addition to the name of the currently selected voice.

The abbreviations in the section separated by a line at the bottom of the display

(“Cnt1”, “Cnt2”, etc) indicate the functions of the corresponding function buttons

below the display (described below).

■ The Normal Voice Display

Play mode.

Voice number.

Voice name.

Reverb on or off.

Stereo output mode.

Element E1 and E2 names.

Voice mode.

Effects in use.

Feature Reference

●

Play Mode

Voice Selection

The VL1’s 128 voices are organized into 8 banks of 16 voices each (8 x 16 = 128).

Any voice can be selected by specifying its bank using the bank keys (a through h),

and its number using the voice number keys (1 through ^).

To select voice “A7”, for example, first press the bank a key and then the voice

number 7 key. The bank a key indicator will flash until the voice number 7 key is

pressed and the D7 voice is actually engaged.

ALL

MOD

RSN

FBD

REV

EFFECT ON / OFF

ELEMENT ON / OFFELEMENT SELECT

MODIFIER ON / OFF

Note that when you select a different bank (or press the same bank button)

the voice directory for the selected bank will appear on the display, showing the names

of all voices in that bank with the cursor located at the currently selected voice number.

The VL1 returns to the normal voice display as soon as you specify the voice number.

You can also press the [ button if you want to stay with the same voice number.

To select a different voice within the same bank it is only necessary to press the

appropriate voice number key. To select a different bank, however, you’ll always have to

press both a bank key and a voice number key (or the [ key). This prevents un-

wanted voices from being selected until you’ve actually specified both the bank and

number of the voice you want to use.

Feature Reference

●

Play Mode

DEC INC

Alternate Voice Selection Methods

● = and - Buttons

These are best for small, step-wise changes —

e.g. selecting adjacent voice numbers, or

numbers that are only a few steps away. Press

the = or - key briefly to decrement or

increment the voice number by one, or hold

either key for continuous decrementing or

incrementing in the corresponding direction.

The bank will switch automatically if you

cross a bank voice-number boundary.

● Data Dial

The data dial provides a fast, efficient way to

cover a broad range of voice numbers when,

for example, you’re looking for a voice but

don’t know the voice number. Simply rotate

the data dial clockwise for higher voice

numbers or counter-clockwise for lower voice

numbers while watching the display. The

banks are automatically switched when neces-

sary as the voice numbers are changed.

●

Using the Voice Directory

Although the voice directory appears automatically any time you select a bank, you

can have the directory displayed continuously if you find it more convenient than the

normal voice display. To switch to the voice directory display, press the • button —

located directly below “Dir” on the display. Voices are selected using the same methods

described above, and the cursor will move to the selected voice.

To return to the normal voice display press the ] or P button.

Feature Reference

●

Play Mode

Controller Views

In the PLAY mode, function buttons ¡ (“Cnt1”) through § (“CS”) are used to

select “controller view” displays that list all controller assignments for the currently

selected voice. You can press the ] or P button from any controller view to

return to the normal play-mode display.

●

(“Cnt1”) through

(“Cnt4”): Main Controllers

¡ through ¢ display the assignments for the controller parameters.

(“Cnt1”)

(“Cnt3”)

™

(“Cnt2”)

Pressure

≥

Page 65.

Embouchure

≥

Page 66.

Pitch

≥

Page 67.

Vibrato

≥

Page 69.

Tounguing

≥

Page 70.

Amplitude

≥

Page 71.

Scream

≥

Page 72.

Breath Noise

≥

Page 73.

Growl

≥

Page 74.

Throat Formant

≥

Page 75.

Dynamic Filter

≥

Page 77.

Harmonic Enhancer

≥

Page 78.

Feature Reference

●

Play Mode

The controller parameters are listed in the left column of the controller view dis-

play, and the controllers assigned to them are listed in the center and right columns,

corresponding to elements 1 and 2, respectively.

●

∞

(“Cnt5”): Other Controller Settings

If you press the ∞ function button from the play mode you’ll see the following

controller view:

(“Cnt4”)

The controller parameters listed in this screen are not in the same category as those

discussed in the preceding section, and therefore need to be introduced separately. All of

the related parameters will be discussed in detail in the Feature Reference manual (pages

listed below).

Damping

≥

Page 80.

Absorption

≥

Page 81.

Polyphony

≥

Page 36.

Sustain

≥

Page 35.

Pitch Bend

≥

Page 35.

Portamento

≥

Page 40.

Effect

≥

Page 45.

Feature Reference

●

Play Mode

●

(“CS”): Continuous Sliders

The § function button calls the Continuous Slider (“CS”) controller view, which

will look something like this:

The continuous sliders — – and ≠ — can be independently assigned to

several parameters that you can control in real time while playing (also see “Quick

Editing In the Play Mode”, below). The parameters available for editing via the continu-

ous sliders are individually preset for each voice. You can select from the available range

by using the “Continuous Slider” assignment function (≥ Page 43).

The continuous slider view shows you which parameters are assigned to which

controller as well as the current positions of the controllers and their corresponding

values.

Quick Editing In the Play Mode

Although detailed voice editing is carried out in the EDIT mode, the – and ≠

sliders on the VL1 panel can be used to change the assigned parameters in real time

while playing in the PLAY mode. This can be used simply an expressive tool, or as a

way to actually change the sound of the voice to suit your individual musical require-

ments. Since the – and ≠ sliders actually edit the parameters to which they are

assigned, the “new” voice created by using the sliders can be stored to one of the VL1’s

voice memory locations and used just as if it had been edited in the EDIT mode (≥ the

STORE operation is described on page 28). The parameters available for editing via the

– and ≠ sliders are individually preset for each voice. You can select from the

available range by using the “Continuous Slider” assignment function (≥ Page 43).

Edit Mode

All voice editing functions are accessed via the

EDIT mode: controller assignments, mixing, modifi-

ers, effects, and more.

● The Voice Number Buttons

In the Edit Mode . . . . . . . . . . . . . . 22

● The Edit Compare Function . . . . . 24

● The Copy Function . . . . . . . . . . . . 25

● Storing Edited Data . . . . . . . . . . . 28

Initial Edit Page . . . . . . . . . . . . . . . . . . . 30

Common Miscellanous . . . . . . . . . . . . . . 34

Common Effect . . . . . . . . . . . . . . . . . . . . 44

Element Controller . . . . . . . . . . . . . . . . . 64

Element Miscellaneous . . . . . . . . . . . . . 84

Element Modifier . . . . . . . . . . . . . . . . . 106

Element Envelope . . . . . . . . . . . . . . . . . 128

Feature Reference

●

Edit Mode

ELEMENT ON / OFF

ELEMENT SELECT

The Voice Number Buttons In the Edit Mode

In the EDIT mode, voice number buttons 1 through 14 assume the functions listed

in purple below the buttons.

●

Element Select

These buttons select the element to be edited in a 2-element voice when an ELE-

MENT parameter is selected. The currently selected element is indicated by the indicators

above the ELEMENT SELECT buttons, and in the function name at the top of the

display page: “E1” for element 1 and “E2” for element 2.

In the example display below, element 2 is selected for editing (“EDIT/E2/

CTRL/PRESSURE”):

The ELEMENT SELECT buttons will not function when a COMMON parameter is

selected. Of course, “E2” can only be selected in a voice that uses two elements. Single-

element voices use only “E1”.

●

Element On/Off

While editing a 2-element voice it is handy to be able to turn one or the other

element off so you can clearly hear the result of edits to the element you are working on.

The ELEMENT ON/OFF buttons perform this function. The on/off status of the elements

is indicated by the indicators above the ELEMET ON/OFF buttons, and by the element

numbers (“12”) at the right end of the second display line: a highlighted number indi-

cates that the element is on, a plain number that the element is off. In the following

display, for example, element 2 is on while element 1 is off:

Feature Reference

●

Edit Mode

ALL

RSN

MODIFIER ON / OFF

ALL

MOD

FBD

REV

EFFECT ON / OFF

●

Effect On/Off

The VL1’s internal digital signal processor provides three effect stages: Modulation,

Feedback Delay, and Reverb. Each stage includes a number of effects. The Modulation,

Feedback Delay, and Reverb stages can be used simultaneously, but only one of the

effects available in each stage can be used at a time.The EXTERNAL EFFECT ON/OFF

buttons can be used to individually or simultaneously turn these effects on of off. The

current status of the effect stages is shown by the indicators above the MOD, FBD, and

REV buttons.

Alternately turns all three effect stages on or off.

Alternately turns the Modulation effect stage on or off.

≥

Page 46.

Alternately turns the Feedback Delay effect stage on or off.

≥

Page 53.

Alternately turns the Reverb effect stage on or off.

≥

Page 60.

ALL

MOD

FBD

REV

These buttons independently or simultaneously turn the VL1’s modifier stages on or

off. This allows fast on/off comparisons that make it easy to hear even subtle changes

produced by editing the modifier parameters.

●

Modifier On/Off

Alternately turns all five modifier stages on or off.

Alternately turns the Harmonic Enhancer stage on or off.

≥

Page 107.

Alternately turns the Dynamic Filter stage on or off.

≥

Page 115.

Alternately turns the Frequency Equalizer stage on or off.

≥

Page 119.

Alternately turns the Impulse Expander stage on or off.

≥

Page 123.

Alternately turns the Resonator stage on or off.

≥

Page 126.

ALL

RSN

Feature Reference

●

Edit Mode

The Edit Compare Function

When editing a voice in the EDIT mode, a copy of the original voice is retained in

the VL1 “edit buffer”, allowing the edited voice to be compared with the edited version

by using the “Edit Compare” function.

The Edit Compare function is engaged by pressing the E button while in the

EDIT mode (after making at least one change to the voice data). When the Edit Compare

mode is engaged the E indicator will flash, the inverse “E”(´) before the voice

number will disappear, and the sound of the original (pre-edit) voice can be monitored.

Press the E button again to return to the EDIT mode and the edited version of the

voice. You can toggle back and forth between the edited and original voices while editing

to monitor the effect of changes you make to the voices parameters.

NOTES ■ Editing can not be carried out while the Edit Compare function is

engaged.

Feature Reference

●

Edit Mode

The Copy Function

The copy function makes it possible to copy common or element data from any

specified voice to the current voice. You can copy all common or element data, or only

the data from a specified group of functions or a single function. It is also possible to

copy the original (pre-edit) data from the voice being edited to restore the specified data

to its original values.

●

Procedure

1. Specify the Data You Want To Copy

In the EDIT mode select the display page and function corresponding to the data

you want to copy:

• To copy all common data, go to the initial EDIT mode display and move the

cursor to the “Voice Name”, “Key Mode”, or “Voice Mode” parameter.

■ Example: Copy all common data.

• To copy all common miscellaneous data select the miscellaneous directory, or

to copy all common effect data select the Effect directory.

■ Example: Copy all common miscellaneous data.

• To copy the data from a single common miscellaneous or common effect

function select the display page for that function.

■ Example: Copy the common miscellaneous element pitch data.

Feature Reference

●

Edit Mode

• To copy all element data, go to the initial EDIT mode display and move the

cursor to the “E1 Name” or “E2 Name” parameter.

■ Example: Copy all element data.

• To copy the E1 or E2 controller, miscellaneous, modifier, or envelope data,

select the corresponding directory display page.

■ Example: Copy all E1 element modifier data.

• To copy the data from a single element function select the display page for

that function.

■ Example: Copy the E2 harmonic enhancer data.

2. Press C

Press the C button to call the COPY display.

3. Select the Voice You Want To Copy From

Use the cursor buttons, data dial, or = and - buttons to select the voice you

want to copy the data from (and the element when copying element data).

• At this point you can play the keyboard to hear how the voice will sound after

the specified data is copied before actually copying the data.

• The voice/element preceded by an asterisk (*) in the copy window is the

current voice/element. If you select this voice/element as the copy source the

Feature Reference

●

Edit Mode

pre-edit data will be copied, thus restoring the specified data to its original

values.

• Press § under “123…” to display the voices in numerical order, or ¶

under “ABC…” to display the voices in alphabetical order. Sometimes it may

take a few seconds to sort the data as specified — the “Now Sorting!”

message will appear during the sort operation.

• Pressing a voice bank button — a through h — instantly moves the cursor

to the first voice in that bank.

• When copying element data in a 2-element voice “E1” or “E2” will appear

above £ — this will be the name of the element

not currently being edited.

In this case the £ function button can be pressed to copy the data from the

second element to the element being edited.

4. Press [ and Confirm To Copy

Press the [ button once you’ve selected the copy source (at this point you can

also press the ] button to cancel the copy function).

Feature Reference

●

Edit Mode

Storing Edited Data

Once you’ve created a new voice in the edit mode, it’s necessary to store the voice

to one of the VL1’s internal memory locations otherwise the edited data will be lost when

a new voice is selected.

NOTES ■ Any previous data in the memory location to which the new voice is

stored will be erased. If you want to keep the previous data, save it to floppy

disk (

≥

Page 166).

■ Edited voice data can only be saved to floppy disk after it has been stored to

an internal memory location.

■ The STORE function can be accessed from the EDIT or PLAY mode.

■ If you have accidentally lost an edited voice by selecting a different voice after

returning to the PLAY mode, the RECALL function can be used to restore the

edited data as long as no other data has been edited in the meantime (

≥

Page

172).

●

Procedure

1. Make Sure Memory Protection Is Off

Make sure that the UTILITY mode Memory Protect function is turned off: press

U to select the UTILITY mode; make sure the “Sys” page is selected; select

“6:Miscellaneous” and press [; move the cursor to “Memory Protect”

and press = to turn it “off”.

2. Press S In the EDIT or PLAY Mode

If you had to go to the UTILITY mode to turn memory protection off, return to

either the EDIT or PLAY mode and press S. At this point you will get a “Memory

Protected” error message if memory protection is turned on — go back and turn

Memory Protect “off”.

3. Select the Destination Memory Location

Use the cursor buttons, data dial, or = and - buttons to select the memory

location you want to store the edited voice to.

NOTES ■ Press

under “

123…

” to display the voices in numerical order, or

under “

ABC…

” to display the voices in alphabetical order. Sometimes it may

take a few seconds to sort the data as specified — the “

Now Sorting!

”

message will appear during the sort operation.

■ Pressing a voice bank button —

through

— instantly moves the cursor

to the first voice in that bank.

Feature Reference

●

Edit Mode

4. Press [ and Confirm To Store

Press the [ button once you’ve selected the store destination (at this point you

can also press the ] button to cancel the store function). If you press [ the

confirmation display will appear.

Press the - button to actually store the data (or = to cancel). “Completed”

will appear on the display when the data has been successfully stored.

5. Press ]

Press the ] button to clear the STORE display and return to the previous mode.

Feature Reference

●

Edit Mode

Initial Edit Page

Select the EDIT mode from either the PLAY or UTILITY mode by

pressing the E button. The initial EDIT display will appear.

NOTES ■ If you are re-entering the EDIT mode while editing a voice (i.e. you

have edited but not yet stored the current voice), the last selected EDIT display

page will appear.

ELEMENT

EFFECT

CONTROLLER

MODIFIER

ENVELOPE

MISCELLANEOUS

EDIT MODE

COMMON

Feature Reference

●

Edit Mode

●

Voice Name

≤ A name of up to 10 characters.

To enter a new voice name position the cursor at the “Voice Name” parameter

and press [ or • (“Name” — “Name” only appears above the • button when

the cursor is positioned at the “Voice Name” parameter). The VOICE NAME display

will appear.

• Use the cursor , and . buttons to move the cursor to the character in the

voice name at the top of the display that you want to change.

• Use the = and - buttons or data dial to select a new character by

moving through the character list row by row.

• Press the ™ button (“Spc”) to enter a space at the current cursor position.

• Press the £ button (“Clr”) to clear the entire voice name.

• Press ] or [ when the voice name is complete.

●

E1 Name, E2 Name

≤ A name of up to 10 characters.

These parameters allow independent names to be entered for the E1 and E2 ele-

ments of the current voice (only E1 is available in a single-element voice). To enter a

new element name position the cursor at the “E1 Name” or “E2 Name” parameter and

press [ or • (“Name”). The ELEMENT NAME display will appear. Procedure is

the same as for the Voice Name parameter, above, except for the function of the ¢

button, below.

• Press the ¢ button to copy the voice name to the element name (suffixes

“_A” and “_B” will be appended to the E1 and E2 names respectively).

●

Key Mode

≤ Mono, Poly, Unison.

In conjunction with the Voice Mode parameter, below, the Key Mode parameter

determines how the VL1’s two elements are used to produce sound.

Initial Edit Page

Mono Only a single note can be played at a time.

Poly Two different notes may be played simultaneously.

Unison Playing a single key produces two notes in unison.

Feature Reference

●

Edit Mode

SaxBass

SaxSaxSaxSax

SaxSax

Sax

●

Voice Mode

≤ Single, Dual.

In conjunction with the Key Mode parameter, above, the Voice Mode parameter

determines how the VL1’s two elements are used to produce sound.

Single Only the sound of one element will be produced at a time.

Dual The sound of two elements may be produced simultaneously.

● Various Key Mode and Voice Mode setting combinations produce the following results:

Key: Mono

Voice: Single

Key: Poly

Voice: Single

Key: Unison

Voice: Single

Key: Mono

Voice: Dual

Key: Poly

Voice: Dual

Key: Unison

Voice: Dual

Feature Reference

●

Edit Mode

• When the cursor is positioned at the “E1 Name” or “E2 Name” parameter

in the initial EDIT mode display, “Swap” appears above the ¶ button.

Pressing this button exchanges the E1 and E2 data, including the element

names. This function can be used to swap the elements used for the high and

low notes when Key Mode is set to “Unison” and Voice Mode is set to

“Dual”. Since E2 always contains data, the Swap function can be use to

temporarily switch elements even when Key Mode is set to “Single”.

Initial Edit Page

Feature Reference

●

Edit Mode

Common Miscellaneous

ELEMENT

EFFECT

CONTROLLER

MODIFIER

ENVELOPE

MISCELLANEOUS

EDIT MODE

COMMON

MISCELLANEOUS

The COMMON MISCELLANEOUS group includes a miscellaneous

range of functions which affect the entire voice.

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

■ 2: Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

■ 3: Element Pitch . . . . . . . . . . . . . . . . . . . . . . . . . 37

■ 4: Element Level & Pan . . . . . . . . . . . . . . . . . . . 38

■ 5: Portamento . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

■ 6: Micro Tuning . . . . . . . . . . . . . . . . . . . . . . . . . 42

■ 7: Continuous Slider . . . . . . . . . . . . . . . . . . . . . 43

Feature Reference

●

Edit Mode

1: Setting

●

Assign Mode

≤ Bottom Note, Top Note, Last Note.

Determines which note(s) will be played when more than one note is played at a

time. Operation is different in the mono, poly, and unison key modes (≥ Page 31), as

noted below. This parameter also affects how the VL1 responds to external MIDI control.

Common Miscellaneous

Bottom Note The lowest note(s) played sounds.

Top Note The highest note(s) played sounds.

Last Note The last note(s) played sounds.

• The above settings apply when the “Mono” key mode is selected.

• When the “Poly” key mode is selected, “Top Note*” will appear in place

of the “Last Note” setting and operation will be the same as when “Top

Note” is selected.

• When the “Unison” key mode is selected, the lowest and highest notes

played will sound regardless of the Assign Mode setting.

●

Pitchbend Mode

≤ Normal, Bottom, Top.

Sets the pitch bend mode. The “Bottom” and “Top” modes are only effective

when the poly or unison key mode (≥ Page 31) is selected.

Normal Both notes are effected by the PITCH wheel.

Bottom The lowest of two notes played will be affected by the pitch wheel.

Top The highest of two notes played will be affected by the pitch wheel.

●

Sustain

≤ off, on.

Turns the VL1 sustain function on or off. When “off” the sustain function will not

work even if sustain is assigned to a footswitch (≥ Page 156) and a footswitch is

plugged into the appropriate FOOT SWITCH jack or a MIDI sustain message is received.

Off Sustain can not be applied via footswitch or MIDI.

On Sustain can be applied via footswitch or MIDI.

Feature Reference

●

Edit Mode

2: Controller

●

Breath Attack Time

≤ 5.00msec … 1.24 sec.

Determines how quickly the VL1 responds to changes in breath pressure applied to

the breath controller. A setting of “5.00msec” produces the fastest response; “1.24

sec” produces the slowest response. This parameter should be used with the “Breath

Attack Gain” parameter, below, to determine overall breath controller response.

●

Breath Attack Gain

≤ 0 … 127.

Determines the amount of audible change produced by a changes in breath pressure

applied to the breath controller. A setting of “0” results in no change; “127” produces

maximum change. “127” is the normal setting for this parameter.

●

Touch EG Time

≤ 5.00msec … 1.24 sec.

Sets the response time of the VL1 Touch Envelope Generator. The Touch Envelope

Generator controls the transition from the initial key velocity to aftertouch pressure when

a key is played. A setting of “5.00msec” produces the fastest response; “1.24 sec”

produces the slowest response.

●

Polyphony Ctrl

≤ off, Modulation Wheel … 119.

The VL1 allows any physical controller to be used to switch between the mono and

poly key modes while playing. This parameter assigns the desired controller to the key-

mode switching function.

The key-mode switching function is off. This setting automatically

selected when Key Mode set to Mono or Unison.

The selected controller will switch between the Mono and Poly key

modes.

Off

Modulation

Wheel … 119.

• The key-mode switching function can only be activated (i.e. a controller

assigned) when the Key Mode parameter is set to “Poly”.

Feature Reference

●

Edit Mode

3: Element Pitch

●

Element 1 Detune

●

Element 2 Detune

≤ -7 … 7.

Produces a slight upward or downward shift in the pitch of Element 1 or Element 2,

and therefore a detuning effect in relation to the other element. Minus values lower the

pitch while positive values raise the pitch. The change in pitch produced by each incre-

ment is very slight (on the order of a few cents per increment). Both elements can be

independently detuned in relation to each other, and in relation to the VL1’s true pitch as

determined by the UTILITY mode “Master Tuning” parameter (≥ Page 154). If a

1-element voice is being edited the “Element 2 Detune” parameter will not appear —

unless the Voice Mode is set to “Single” and the Key Mode is set to “Unison”. In the

latter case the “Element 2 Detune” parameter appears because the same voice is

being played in the unison mode.

●

Element 1 Note Shift

●

Element 2 Note Shift

≤ -64 … 63.

Shifts the pitch of Element 1 or Element 2 up or down in semitone increments.

Minus values lower the pitch while positive values raise the pitch. The pitches of both

elements can be independently shifted in relation to each other, and in relation to the

VL1’s true pitch as determined by the UTILITY mode “Master Tuning” parameter

(≥ Page 154).

●

Element 1 Random Pitch

●

Element 2 Random Pitch

≤ 0 … 7.

Produces a slight random variation in the pitch of Element 1 or Element 2, simulat-

ing the effect of acoustic instruments in which perfectly stable effect is rarely achieved. A

setting of “0” produces no random pitch variation; “7” produces maximum random pitch

variation.

Common Miscellaneous

Feature Reference

●

Edit Mode

063-64

Sound

Left Right

4: Element Level & Pan

●

Element 1 Level

●

Element 2 Level

≤ 0 … 127.

Sets the level (volume) of the output from Element 1 or Element 2. A setting of “0”

produces no output; “127” produces maximum output. Indepedent level parameters are

provided for Element 1 and Element 2, making it easy to create the desired “balance”.

The graphic bar to the right of the numeic parameter provides a visual indication of the

level setting: higher settings move the graphic “slider” to the right.

●

Element 1 Pan L

●

Element 1 Pan R

●

Element 2 Pan L

●

Element 2 Pan R

≤ -64 … 63.

Determines the position of Element 1 or Element 2 in the stereo sound field. Nor-

mally there would be only one pan parameter for each element, placing the sound of the

element anywhere from full left to right in the stereo sound field. The output from the

VL1 elements and modifier stages is already in stereo, so two pan parameters (L and R)

and provided for each element, offering maximum panning versatility. The “Element 1

Pan L” parameter, for example, determines the position of the left-channel output signal

from Element 1, while the “Element 1 Pan R” parameter determines the position of

the right-channel output from the same element. The graphic bar to the right of the

numeric parameters provides a visual indication of the pan settings: the “L” slider extends

above the bar and the “R” slider extends below the bar. Higher settings move the corre-

sponding slider to the right.

• To reproduce the original stereo

sound of the element, set the

“Pan L” parameter to “-64”

and the “Pan R” parameter to

“63”.

Feature Reference

●

Edit Mode

063-64

Left Right

Sound

063-64

Left Right

Sound

• To limit the sound of Element 1

to the left half of the sound field,

for example, set “Element 1

Pan L” to “-64” and “Ele-

ment 1 Pan R” to “0”.

• If both the “L” and “R” param-

eters are set to the same value,

the sound of the corresponding

element will appear as a mono

source at the appropriate position

in the stereo sound field. If both

parameters are set to “0”, for

example, the sound of the

element will be heard only in the

center of the sound field.

• The Element 2 pan and level parameters will not appear if the Voice Mode

parameter is set to “Single”.

• The pan parameters have no effect if the UTILITY mode “Output” param-

eter is set to “Monaural”.

Common Miscellaneous

Feature Reference

●

Edit Mode

5: Portamento

●

Portamento Mode

≤ Full Time, Fingered.

Portamento produces a “slide” effect between subsequently played notes. The

“Portamento Mode” parameter determines how the portamento slide is produced.

The portamento slide will occur between any two subsequent notes

when the portamento switch is on, even if the first note is released

before the scond is played.

The portamento slide will only occur if the first note is still held when

the second note is played.

Full Time

Fingered

• If the “Key Mode” parameter (≥ Page 31) is set to “Poly” or “Unison”

the “Portamento Mode” parameter is fixed at “Full Time” and cannot

be changed.

●

Time MIDI Control

≤ off, on.

The portamento time (the length of the slide between notes) can be controlled in

realtime via a foot controller connected to the FOOT CONTROLLER 2 jack, the MODU-

LATION 2 wheel, or MIDI portamento time messages from an external device. This

parameter turns realtime portamento time control off or on.

• In order to use the foot controller or modulation wheel for portamento time

control, use the UTILITY mode “Assignable Controller” page (≥

Page 156) to assign the foot controller or modulation wheel to “Porta

Time” (MIDI control number 005).

●

Time

≤ 0 … 127.

This parameter becomes active only when the “Time MIDI Control” param-

eter, above, is turned “off”. The “Time” parameter sets the portamento time. A setting

of “0” produces the fastest portamento time; “127” produces the longest portamento

slide effect.

●

Element 1

≤ off, on.

Turns portamento off or on for element 1 only.

Feature Reference

●

Edit Mode

●

Element 2

≤ off, on.

Turns portamento off or on for element 2 only.

• The “Element 2” parameter will not appear if the “Voice Mode” param-

eter (≥ Page 32) is set to “Single”.

Common Miscellaneous

Feature Reference

●

Edit Mode

6: Micro Tuning

●

Element 1

●

Element 2

≤ off, I-1 … I-2, P-1 … P-54.

Selects the micro-tuning for Element 1 or Element 2.

Equal Temperament: the standard modern keyboard tuning with

perfectly even intervals between all 12 notes of the scale. This tuning

allows transposition to any key without modification.

Internal Microtuning: These tuning are included in the system data on

the VL-1 voice disk.

Pure Major C … Pure Major B: A brass-instrument tuning based on

their natural harmonic series. Produces a beautiful beat-free sound in

ensemble, but the tuning must be changed to match the key of the

music.

Pure Minor C … Pure Minor B: Same as the Pure Major scales

above, but for minor keys.

Mean Tone C … Mean Tone B: This tuning was originally devised to

eliminate the conflict caused by the third degree of the Pythagorean

tuning (below). The tuning must be matched to the key of the music.

Pythagorean: A classic tuning from ancient Greece — with a few

rough spots that were fixed in later improvements. The tuning must be

matched to the key of the music.

Werckmeister: This and the following two tunings were created to

allow transposition to any key without the need for re-tuning. They have

the curious chacteristic, however, that the “tension” of the sound

increases in proportion to the number of sharps or flats in the key

being played. Many of the classics were created using these tunings.

Kirnberger: See “Werckmeister”.

Vallotti & Young: See “Werckmeister”.

1/4 Shifted Equal: This is an equal temperament tuning with the

overall pitch raised 1/4 tone. It can be used with other instruments in

standard equal temperament tuning for some unusual and very “tense”

effects.

1/4 Tone: All semitones on the keyboard become 1/4-tone intervals.

1/8 Tone: All semitones on the keyboard become 1/8-tone intervals.

Off

I-1, I-2

P-1 … P-12

P-13 … P-24

P-25 … P-36

P-37 … P-48

P-49

P-50

P-51

P-52

P-53

P-54

• The I-1 and I-2 tunings (Internal Microtuning) cannot be edited or modified

using the VL1. Microtuning data from the Yamaha SY99 or SY77 synthesizer

can, however, can be loaded into the VL1 via a MIDI bulk dump or parameter

change operation.

Feature Reference

●

Edit Mode

• The “Element 2” parameter will not appear if the “Voice Mode” param-

eter (≥ Page 32) is set to “Single”.

Common Miscellaneous

7: Continuous Slider

●

CS1

●

CS2

≤ off, Com, E1, E2, Both — plus the parameters available for the current voice.

Assigns the available common or element edit parameters to the – or ≠

continuous slider. The continuous sliders can then be used in the PLAY mode to edit the

assigned parameters in real time while playing (the same applies to the EDIT and UTIL-

ITY modes). The parameter consists of two parts which can be selected independently by

moving the cursor horizontally. The first (leftmost) part determines what type of param-

eter will be controlled.

Continuous slider not assigned. Choose this setting if you don’t want

the continuous slider to affect any edit parameters.

Selects the common edit parameters.

Selects the element 1 edit parameters. This setting will appear as “E1*”

if previously set to “E2” or “Both” with the Voice Mode parameter set to

“Dual”, then the Voice Mode parameter is switched to “Single”.

Selects the element 2 edit parameters.

Selects element edit parameters that will affect both element 1 and

element 2.

off

Com

Both

The second (rightmost) is the actual parameter which will be controlled. The param-

eters available for editing via the continuous sliders are individually preset for each voice.

• Since the continuous sliders actually edit the parameters to which they are

assigned, the “new” voice created by using the sliders can be stored to one of

the VL1’s voice memory locations and used just as if it had been edited in the

EDIT mode (≥ the STORE operation is described on page 28).

• The continuous slider view function, available in the PLAY mode (≥ Page

13), shows you which parameters are assigned to which controller as well as

the current positions of the controllers and their corresponding values.

Feature Reference

●

Edit Mode

Common Effect

ELEMENT

CONTROLLER

MODIFIER

ENVELOPE

MISCELLANEOUS

EDIT MODE

COMMON

EFFECT

The COMMON EFFECT parameters provide access to the VL1’s

sophisticated three-stage digital signal processing system.

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

■ 2: Modulation Effect . . . . . . . . . . . . . . . . . . . . . . 46

● Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

● Pitch Change . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

● Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

■ 3: Feedback Delay . . . . . . . . . . . . . . . . . . . . . . . 53

● Mono Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

● L,R Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

● L,C,R Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

■ 4:Reverberation . . . . . . . . . . . . . . . . . . . . . . . . . 60

● Hall1, Hall2, Room1, Room2, Studio, Plate,

Space, Reverse . . . . . . . . . . . . . . . . . . . . . . . . . 61

Feature Reference

●

Edit Mode

Common Effect

1: Setting

●

Feedback Delay/Reverb Mode

≤ Serial, Parallel.

Determines whether the Feedback Delay and Reverb effect stages are connected in

series (Serial) or in parallel, as shown in the illustration.

Feedback

Delay

Modulation

Reverb

Serial Mode

From

Element

Output

Parallel Mode

Feedback

Delay

From

Element

Output

Reverb

Modulation

●

Effect Control — Destination Effect

≤ off, Flanger Freq., Pitch Change Wet/Dry, Distortion Presence, FB Delay Send Level,

Reverb Send Level.

This and the following parameter make it possible to control certain effect param-

eters in real time via any physical controller. Use this parameter to select the effect

parameter you want to control (only settings corresponding to the currently selected

effects will be available). If the currently selected effect stage is turned off, “isn’t

used” will appear on the display and selection will not be possible.

●

Effect Control — Controller

≤ off, Modulation Wheel … Velocity.

Selects the controller which will be used to control the parameter selected via the

“Destination Effect” parameter. All MIDI control numbers and keyboard veloc-

ity are available. Be sure to turn this parameter “off” if you don’t require realtime effect

control.

Feature Reference

●

Edit Mode

2: Modulation Effect

●

Modulation Effect Type

≤ off, Flanger, Pitch Change, Distortion.

Selects the type of effect to be produced by the modulation effect stage. The effect

types and their parameters are individually described on the following pages. No effect

parameters appear when the modulation effect stage is turned “off”.

This type of effect is created by slightly delaying the sound and

periodically varying the delay time. The delayed signal is then added to

the direct signal causing a variable comb-filter effect which results in

the familiar “swishing” flanger sound.

A dual pitch change effect which can be used in the Mono mode, in

which both pitch-shifted notes appear on both channels, or the Stereo

mode in which one pitch-shifted note appears on the left channel and

the other on the right. The pitch of the two pitch-shifted notes can be

set over a two-octave range — from one octave below to one octave

above the input note.

An extremely versatile distortion effect which offers transistor, vintage

tube, fuzz and other distortion types, a variety of speaker types, and a

comprehensive range of other parameters that can be used to refine

the distortion sound.

Flanger

Pitch Change

Distortion

Feature Reference

●

Edit Mode

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Element on/off — E1: & E2:

≤ off, on.

In this parameter the cursor can be positioned at “E1:” or “E2:” to individually turn

the flanger effect on or off for elements 1 and 2, respectively. When “on” the output of

the corresponding element is fed to the input of the modulation stage, and when “off”

the modulation stage is bypassed. The “E2:” parameter will not appear when editing a

single-element voice.

●

Wave

≤ Triangle, Sine, Random.

Selects the waveform which will be used to modulate the flanger effect.

Flanger

Common Effect

●

Freq.

≤ 0.057 … 40.0 Hz when Triangle or Sine Wave selected,

≤ 0.229 … 160.0 Hz when Random Wave selected.

Sets the speed of modulation and therefore the rate of flanger effect variation.

●

Depth

≤ 0 … 100 %.

Sets the depth of modulation. Higher values produce deeper modulation and there-

fore a more pronounced flanger effect.

Triangle

Sine

Random

Feature Reference

●

Edit Mode

L In

R In

L Out

R Out

Flanger

●

Delay

≤ 0.33 … 32.87 ms.

Sets the flanger delay time (the flanger effect is basically produced by modulating

the delay time of one signal in relation to another). Shorter delay times produce the

greatest effect in the high-frequency range, while longer delay times extend the effect to

the middle and lower frequencies. Delays longer than about 5 milliseconds produce a

more chorus-like effect.

●

Phase

≤ -180.0 … 180.0 deg.

Sets the phase different between the left and right channel flanger signals. The

larger the value, the greater the “spread” in the sound. A setting of “0” produces a

centered effect.

●

FB Gain

≤ -100 … 100 %.

Determines the amount of effect-sound feedback returned to the input of the flanger

stage. Higher negative or positve values produce a more pronounced effect.

●

High

≤ 0.1 … 1.0.

Determines the amount of high-frequency effect-sound feedback returned to the

input of the flanger stage. Lower values produce more cut in the high-frequency range.

●

Analog Feel

≤ 0 … 10.

This parameters simulates the sound of traditional analog flanger devices. The

higher the value the stronger the “analog feel”.

●

Wet/Dry Balance

≤ 0 … 100 %.

Sets the balance between the direct (“dry”) and effect (“wet”) sound. Higher values

produce a greater proportion of effect sound in relation to direct sound.

■ Flanger Effect Block Diagram

Flanger

Feature Reference

●

Edit Mode

Pitch Change

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Element on/off — E1: & E2:

≤ off, on.

In this parameter the cursor can be positioned at “E1:” or “E2:” to individually

turn the pitch change effect on or off for elements 1 and 2, respectively. When “on” the

output of the corresponding element is fed to the input of the modulation stage, and when

“off” the modulation stage is bypassed. The “E2:” parameter will not appear when

editing a single-element voice.

●

Mode

≤ Monaural, Stereo.

Selects the monaural or stereo pitch change effect mode. In the monaural mode both

pitch-shifted notes appear on both channels. In the stereo mode one pitch-shifted note

appears on the left channel and the other on the right.

■ Stereo Mode BLock Diagram

Common Effect

L In

R In

L Out

R Out

Pitch Change L

Pitch Change R

L In

R In

L Out

R Out

Pitch Change 1

Pitch Change 2

■ Monaural Mode Block Diagram

Feature Reference

●

Edit Mode

●

1 Pitch (L Pitch)

●

2 Pitch (R Pitch)

≤ -12 … 12.

These two parameters individually set the pitch of the first and second pitch-

changed note between one octave below (“-12”) and one octave above (“+12”) the input

note. When the “Stereo” mode is selected, the “1 Pitch” parameter applies to the

left channel and the “2 Pitch” parameter to the right.

●

1 Fine (L Fine)

●

2 Fine (R Fine)

≤ -100 … 100.

Permit fine tuning of the first and second pitch-changed note in 1-cent steps (1 cent

is 1/100th of a semitone). When the “Stereo” mode is selected, the “L Fine” param-

eter applies to the left channel and the “R Fine” parameter to the right.

●

1 Output (L Output)

●

2 Output (R Output)

≤ 0 … 100 %.

Set the output level of the corresponding pitch-changed note. The higher the value

the higher the output level. When the “Stereo” mode is selected, the “1 Output”

parameter applies to the left channel and the “2 Output” parameter to the right.

●

Wet/Dry Balance

≤ 0 … 100 %.

Sets the balance between the direct (“dry”) and effect (“wet”) sound. Higher values

produce a greater proportion of effect sound in relation to direct sound. When set to “0”

no pitch change effect is produced.

Pitch Change

Feature Reference

●

Edit Mode

Distortion

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Element on/off — E1: & E2:

≤ off, on.

In this parameter the cursor can be positioned at “E1:” or “E2:” to individually

turn the distortion effect on or off for elements 1 and 2, respectively. When “on” the

output of the corresponding element is fed to the input of the modulation stage, and when

“off” the modulation stage is bypassed. The “E2:” parameter will not appear when

editing a single-element voice.

●

Overdrive

≤ 0 … 100 %.

Sets the intensity of the overdrive or distortion effect. Higer values produce more

distortion.

●

Device

≤ Transistor, Vintage Tube, Distortion 1, Distortion 2, Fuzz.

Determines the basic sound of the distortion effect.

Common Effect

The crisp, tight distortion of an overdriven transistor amplifier.

Simulates the warm, relatively “soft” distortion produced by vacuum

tube amplifiers.

A traditional “stomp-box” type distortion unit, type 1.

A traditional “stomp-box” type distortion unit, type 2.

Early “fuzz boxes” produced this type of distortion — rough and

somewhat rude.

Transistor

Vintage Tube

Distortion 1

Distortion 2

Fuzz

Feature Reference

●

Edit Mode

L In

R In

L Out

R Out

Distortion

●

Output Level

≤ 0 … 100 %.

Sets the output level of the distortion sound. Higher values produce higher level.

●

Speaker

≤ Flat, Stack, Combo, Twin, Radio, Megaphone.

Simulates a variety of speaker types and configurations via which the distortion

sound might be reproduced.

Distortion

No speaker — the sound of a “direct feed” to a recording or sound

reinforcement console.

The powerful, expansive sound of stacked speaker cabinets.

A single 12" speaker unit in an open-backed enclosure.

Two 12" speaker units in a relatively small open-backed enclosure.

The small, compressed, but pleasant tone of a radio receiver.

Constricted tone with emphasis on the middle frequencies.

Flat

Stack

Combo

Twin

Radio

Megaphone

●

Presence

≤ -10 … 10.

Varies the “presence” or “brilliance” of the sound. Higher values produce more

presence and “punch”.

■ Distortion Effect Block Diagram

Feature Reference

●

Edit Mode

3: Feedback Delay

●

Delay Type

≤ off, Mono, L,R, L,C,R.

Selects the type of effect to be produced by the Feedback Delay effect stage. The

effect types and their parameters are individually described on the following pages. No

effect parameters appear when the Feedback Delay effect stage is turned “off”.

Mono Delay

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Return

≤ 0 … 100 %.

Determines how much of the delayed sound is mixed with the direct sound. Higher

values produce higher delay sound levels.

The Mono delay effect produces a single delay sound which appears in

the center of the stereo sound field.

This variation provides independently programmable delays for the left

and right stereo channels.

Independent delays are provided for the left and right channels, plus a

center delay.

Mono

L,R

L, C, R

Common Effect

Feature Reference

●

Edit Mode

●

FB Delay Time

≤ 0 … 1024 ms.

Sets the delay time between repeats. The higher the value the longer the delay.

• Use the VL1 “Time Calculation” function (≥ Page 59) to enter delay times

based on musical tempo and note lengths.

●

FB Gain

≤ 0 … 100 %.

Determines the amount of effect-sound feedback returned to the input of the delay

stage. Higher values produce a greater number of repeats.

●

High

≤ 0.1 … 1.0.

Produces a natural decay in the high-frequency components of subsequent repeats.

The lower the value the faster and more pronounced the drop-off in high-frequencies.

●

Delay Time

≤ 0 … 1024 ms.

Sets the delay time between the direct sound and the first repeat.

• Use the VL1 “Time Calculation” function (≥ Page 59) to enter delay times

based on musical tempo and note lengths.

●

Level

≤ 0 … 100 %.

Sets the overall level of the delay sound. Higher values produce higher delay level.

Mono Delay

Time

Volume

Level

Direct Sound

FB Delay TimeDelay Time

FB Gain

■ Mono Delay Effect Block Diagram

L In

R In

L Out

R Out

Delay

Feature Reference

●

Edit Mode

L,R Delay

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Return

≤ 0 … 100 %.

Determines how much of the delayed sound is mixed with the direct sound. Higher

values produce higher delay sound levels.

●

Lch Delay Time

●

Rch Delay Time

≤ 0 … 512 ms.

Set the delay time between repeats. Independent parameters are provided for the left

(“Lch”) and right (“Rch”) channels.

• Use the VL1 “Time Calculation” function (≥ Page 59) to enter delay times

based on musical tempo and note lengths.

●

Lch Level

●

Rch Level

≤ 0 … 100 %.

Set the overall level of the delay sound. Higher values produce higher delay level.

Independent parameters are provided for the left (“Lch”) and right (“Rch”) channels.

●

Lch FB Gain

●

Rch FB Gain

≤ 0 … 100 %.

Determine the amount of effect-sound feedback returned to the input of the delay

stage. Higher values produce a greater number of repeats. Independent parameters are

provided for the left (“Lch”) and right (“Rch”) channels.

Common Effect

Feature Reference

●

Edit Mode

L In

R In

L Out

R Out

Delay

●

Lch High

●

Rch High

≤ 0.1 … 1.0.

Produces a natural decay in the in the high-frequency components of subsequent

repeats. The lower the value the faster and more pronounced the drop-off in high-frequen-

cies. Independent parameters are provided for the left (“Lch”) and right (“Rch”) chan-

nels.

L,R Delay

■ L,R Delay Effect Block Diagram

Feature Reference

●

Edit Mode

L,C,R Delay

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Return

≤ 0 … 100 %.

Determines how much of the delayed sound is mixed with the direct sound. Higher

values produce higher delay sound levels.

●

FB Delay Time

≤ 0 … 1024 ms.

Sets the delay time between repeats. The higher the value the longer the delay.

• Use the VL1 “Time Calculation” function (≥ Page 59) to enter delay times

based on musical tempo and note lengths.

●

FB Gain

≤ 0 … 100 %.

Determines the amount of effect-sound feedback returned to the input of the delay

stage. Higher values produce a greater number of repeats.

●

High

≤ 0.1 … 1.0.

Produces a natural decay in the in the high-frequency components of subsequent

repeats. The lower the value the faster and more pronounced the drop-off in high-frequen-

cies.

Common Effect

Feature Reference

●

Edit Mode

L In

R In

L Out

R Out

Delay

●

Lch Delay Time

●

Cch Delay Time

●

Rch Delay Time

≤ 0 … 1024 ms.

Set the delay time between the direct sound and the first repeat. Independent param-

eters are provided for the left (“Lch”), center (“Cch”), and right (“Rch”) channels.

• Use the VL1 “Time Calculation” function (≥ Page 59) to enter delay times

based on musical tempo and note lengths.

●

Lch Level

●

Cch Level

●

Rch Level

≤ 0 … 100 %.

Set the overall level of the delay sound. Higher values produce higher delay level.

Independent parameters are provided for the left (“Lch”), center (“Cch”), and right

(“Rch”) channels.

L,C,R Delay

■ L,C,R Delay Effect Block Diagram

Feature Reference

●

Edit Mode

Since the goal in producing a delay effect is often to match the delay time to a

musical time value, the VL1 includes a “time calculation” function that makes it easy to

convert standard note values to their corresponding delay times in milliseconds.

1. Select a Delay Time Parameter

Position the cursor at the delay time parameter you want to edit — “Calc” will

appear above the • button.

2. Press •

Press the • function button (“calc”). The “TIME CALCULATION” window

will appear.

3. Set the Required Tempo

Use the data dial or = and - buttons to specify the tempo you will be

playing at (quarter-note beats per minute). The delay time corresponding to one quarter

note at the specified tempo will appear, in milliseconds, below the selected tempo.

4. Select the Required Note Length

Use the £ through ¶ buttons to select the note length to which you want to

match the delay time. The corresponding delay time will appear, as in the preceding step.

5. Press [

Press the [ button. The “TIME CALCULATION” window will disappear and

the calculated delay time will automatically be entered for the delay time parameter (you

can also press ] to cancel this operation).

Musical Time Calculation

Common Effect

Feature Reference

●

Edit Mode

4: Reverberation

●

Reverb Type

≤ off, Hall1, Hall2, Room1, Room2, Studio, Plate, Space, Reverse.

Selects the type of effect to be produced by the Reverb effect stage. Unlike the

preceding effect stages, the parameters are the same for all Reverb effect types. No effect

parameters appear when the Reverb effect stage is turned “off”.

A simulation of the reverbation characteristics of a fairly standard

concert hall.

This hall simulation produces a richer low-frequency reverb sound than

the Hall 1 program.

The ambience of a small room rather than a large hall. This effect is

ideal when you just want a subtle touch of ambience.

A larger room than the Room 1 simulation, with a correspondingly

“bigger” reverb sound.

In recording studios it is generally desirable to suppress low-frequency

reverbeation without entirely losing the “live” sound of the room. The

Studio program simulates this type of environment.

The plate reverb unit is a classic tool of the recording trade — it was

the first mechanical method of creating artificial reverberation that

capable of producing satisfactory results in the studio. This is a very

realistic simulation.

A diffuse reverberation of the type you might experience in an ex-

tremely large space.

In this effect the reverb sound plays in reverse, building up to

maximum level rather than decaying as normal.

Hall 1

Hall 2

Room 1

Room 2

Studio

Plate

Space

Reverse

Feature Reference

●

Edit Mode

Time

Level

Reverb

Boost

Hall1, Hall2, Room1, Room2, Studio, Plate, Space, Reverse

• Use the ¡ (“>”) and ™ (“<”) buttons to switch between the two pages

of effect parameters.

●

Return

≤ 0 … 100 %.

Determines how much of the reverb sound is mixed with the direct sound. Higher

values produce higher reverb sound levels.

●

Reverb Time

≤ 0.05 … 100.0 sec.

Sets the amount of time it takes for the reverb sound to decay by 60 dB (virtually to

silence).

●

Reverb Time Boost

≤ 0 … 10.

This parameter ca be used to extend the tail end of the reverb sound. The higher the

value the greater the “boost”.

Common Effect

Feature Reference

●

Edit Mode

Time

Level

Reverb

Initial

Delay

Direct Sound

●

High Control

≤ 0.1 … 1.0.

Sets the reverb time of the high frequencies in relation to the overall reverb time.

Higher values produce longer high-frequency reverb times, gradually approaching the

overall reverb time.

●

Diffusion

≤ 0 … 10.

Adjusts the left-right “spread” of the reverb sound. The higher the value the greater

the spread.

●

Initial Delay

≤ 0 … 405 ms.

Sets the delay time before the reverb sound begins.

●

Feel

≤ 0 … 3.

Selects one of four variations in density or overall sound available for each of the

VL1’s reverb types.

●

Bass

≤ -21 … 12.

Emphasizes the bass frequencies. The higher the value the greater the bass empha-

sis.

●

Treble

≤ -21 … 12.

Emphasizes the treble frequencies. The higher the value the greater the treble

emphasis.

Feature Reference

●

Edit Mode

■ Reverb Effect Block Diagram

Common Effect

L In

R In

L Out

R Out

Reverb

Feature Reference

●

Edit Mode

Element Controller

ELEMENT

EFFECT

MODIFIER

ENVELOPE

MISCELLANEOUS

EDIT MODE

COMMON

CONTROLLER

MISCELLANEOUS

■ 1: Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

■ 2: Embouchure . . . . . . . . . . . . . . . . . . . . . . . . . . 66

■ 3: Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

■ 4: Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

■ 5: Tonguing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

■ 6: Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

■ 7: Scream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

■ 8: Breath Noise . . . . . . . . . . . . . . . . . . . . . . . . . 73

■ 9: Growl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

■ 10: Throat Formant . . . . . . . . . . . . . . . . . . . . . . 75

■ 11: Dynamic Filter . . . . . . . . . . . . . . . . . . . . . . . 77

■ 12; Harmonic Enhancer . . . . . . . . . . . . . . . . . . . 78

■ 13: Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

■ 14: Absorption . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Pressing the • button (“S&R”) from this page will take you to the

“CONTROLLER SEARCH & REPLACE” window, allowing you to see

which controllers are assigned to which parameters, and to modify the

assigmments as required (≥ Page 82).

Feature Reference

●

Edit Mode

1: Pressure

• The ¶ button (“Fpag”) can be used to go directly the next Element Control-

ler page without having to return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Pressure” parameter corresponds to the amount of breath pressure applied to a

reed or mouthpiece, or the speed of the bow applied to a string. Pressure variations affect

both volume and timbre. The “Controller” parameter specifies the controller to be

used for pressure control. When set to “off” maximum pressure is applied at all times.

• Please note that accurate keyboard pitch is produced only at maximum pres-

sure.

• The actual pressure value applied to the VL1 tone generator is the product of

the pressure from the controller and that from the pressure envelope (≥

Page 128).

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to pressure. The

higher the value the greater the variation. Positive values cause an increase in pressure in

response to higher controller values (e.g. increased breath pressure or higher modulation

wheel position), while minus values cause a decrease in pressure in response to higher

controller values. The “Depth” setting is reflected in the graph to the right of the param-

eters — the horizontal axis represents the controller value and the vertical axis represents

pressure.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and pressure. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in pressure. As the curve value increases the lower end of the controller

range has relatively little effect on the sound while higher controller values produce more

dramatic changes. Negative curve values have the opposite effect: the sound changes

dramatically at low controller values while higher values produce relatively little effect.

The “Curve” setting is reflected in the graph to the right of the parameters — the

horizontal axis represents the controller value and the vertical axis represents pressure.

Element Controller

Feature Reference

●

Edit Mode

2: Embouchure

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Embouchure” parameter corresponds to the tightness of the lips against the

reed or against each other. In a string instrument voice Embouchure corresponds to how

strongly the bow is pressed against the string. Affects both pitch and timbre. The “Con-

troller” parameter specifies the controller to be used for embouchure control. When

set to “off” medium embouchure is applied at all times.

• Please note that accurate keyboard pitch is produced only at medium embou-

chure.

• The actual embouchure value applied to the VL1 tone generator is a mix of

the embouchure from the controller and that from the embouchure and pitch

envelopes (≥ Page 130).

●

Upper Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to embouchure

when the controller is set to its maximum position (e.g. a modulation wheel rolled all the

way up). The higher the value the greater the variation. Positive values cause an increase

in embouchure in response to higher controller values, while minus values cause a

decrease in embouchure in response to higher controller values. The value of the “Lower

Depth” parameter, below, is automatically changed in response to changes in the “Up-

per Depth” value (the “Lower Depth” value is always negative when “Upper

Depth” is positive, and vice versa).

●

Lower Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to embouchure

when the controller is set to it minimum position (e.g. a modulation wheel rolled all the

way down). The higher the value the greater the variation. Positive values cause an

increase in embouchure in response to lower controller values, while minus values cause

a decrease in embouchure in response to lower controller values. Changing the value of

the “Lower Depth” parameter has no effect on the “Upper Depth” value. The

Feature Reference

●

Edit Mode

“Lower Depth” parameter is not available when the “Mode” parameter, below, is set

to “Minimum Base”.

●

Mode

≤ Center Base, Minimum Base.

Selects the controller value (position) which will produce “normal” embouchure.

When set to “Center Base” a central controller position will produce normal embou-

chure, allowing both downward and upward variation. A setting of “Minimum Base”

will produce normal embouchure when the controller is set to its minimum position,

allowing only upward variation.

Element Controller

3: Pitch

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Pitch” parameter changes the length of the air column or string, and thereby

the pitch of the sound. The “Controller” parameter specifies the controller to be used

for pitch control (normally this is “Pitch Bend — the VL1 PITCH wheel). When set

to “off” no pitch variation is produced.

• The actual pitch value applied to the VL1 tone generator is a mix of the pitch

value from the controller and that from the embouchure and pitch envelopes

(≥ Page 130).

• For the same type of simple pitch control available in conventional synthesiz-

ers, assign only the Pitch parameter to controller you intend to use for pitch

control (normally the pitch bend wheel). For more natural, realistic pitch bend

effects, it is sometimes effective to assign both the Pitch and Embouchure

parameters to the same controller.

Feature Reference

●

Edit Mode

●

Upper Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to pitch when the

controller is set to its maximum position (e.g. a modulation wheel rolled all the way up).

The higher the value the greater the variation. Positive values cause an increase in pitch

in response to higher controller values, while minus values cause a decrease in pitch in

response to higher controller values. The value of the “Lower Depth” parameter,

below, is automatically changed in response to changes in the “Upper Depth” value

(the “Lower Depth” value is always negative when “Upper Depth” is positive, and

vice versa).

●

Lower Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to pitch when the

controller is set to it minimum position (e.g. a modulation wheel rolled all the way

down). The higher the value the greater the variation. Positive values cause an increase in

pitch in response to lower controller values, while minus values cause a decrease in pitch

in response to lower controller values. Changing the value of the “Lower Depth”

parameter has no effect on the “Upper Depth” value. The “Lower Depth” param-

eter is not available when the “Mode” parameter, below, is set to “Minimum Base”.

●

Mode

≤ Center Base, Minimum Base.

Selects the controller value (position) which will produce normal pitch. When set to

“Center Base” a central controller position will produce normal pitch, allowing both

downward and upward variation. A setting of “Minimum Base” will produce normal

pitch when the controller is set to its minimum position, allowing only upward variation.

• Please note that accurate keyboard pitch is produced only when the “Mode”

parameter is set to “Center Base”.

Feature Reference

●

Edit Mode

4: Vibrato

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Vibrato parameter

page (≥ Page 135), also available from the ELEMENT ENVELOPE direc-

tory. You can then return to the controller vibrato page by pressing •

(“Ctrl”) again.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

This is essentially a standard vibrato (pitch modulation) effect. An extensive range

of parameters makes it possible to achieve extremely natural vibrato effects. The amounts

of vibrato applied via pitch and embouchure, for example, are independently programma-

ble. The “Controller” parameter specifies the controller to be used for vibrato depth

control. When set to “off” no vibrato can be applied.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to vibrato. The

higher the value the greater the variation. Positive values cause an increase in vibrato

depth in response to higher controller values (e.g. increased breath pressure or higher

modulation wheel position), while minus values cause a decrease in vibrato depth in

response to higher controller values.

• No vibrato effect can be applied via any controller if the ELEMENT ENVE-

LOPE “Vibrato Depth”, “Depth to Embouchure”, or “Depth to

Pitch” parameters are set to “0” (≥ Page 135, 136).

Element Controller

Feature Reference

●

Edit Mode

5: Tonguing

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Tonguing” parameter simulates the half-tonguing technique used by saxo-

phone players by changing the “slit” of the reed. The slit is the space between the tip of

the reed and the mouthpiece. The “Controller” parameter specifies the controller to

be used for tonguing control. When set to “off” no tonguing is applied.

• Please note that accurate keyboard pitch is produced only when maximum

tonguing is applied or the tonguing controller is turned off.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to tonguing. The

higher the value the greater the variation. Positive values cause an decrease in tonguing in

response to higher controller values (e.g. increased breath pressure or higher modulation

wheel position), while minus values cause an increase in tonguing in response to higher

controller values. The “Depth” setting is reflected in the graph to the right of the param-

eters — the horizontal axis represents the controller value and the vertical axis represents

tonguing.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and tonguing. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in tonguing. As the curve value increases the lower end of the controller

range has relatively little effect on the sound while higher controller values produce more

dramatic changes. Negative curve values have the opposite effect: the sound changes

dramatically at low controller values while higher values produce relatively little effect.

The “Curve” setting is reflected in the graph to the right of the parameters — the

horizontal axis represents the controller value and the vertical axis represents tonguing.

Feature Reference

●

Edit Mode

6: Amplitude

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

Unlike pressure, the “Amplitude” parameter controls the volume of the sound

without varying timbre. The “Controller” parameter specifies the controller to be

used for amplitude control. When set to “off” no amplitude control can be applied.

• Amplitude control via this parameter actually occurs between the modifier

Dynamic Filter and Equalizer stages, the effect of the subsequent impulse

expander and resonator stages is therefore not affected by the amplitude

setting. In contrast, amplitude control applied via MIDI volume control change

number (007) affects the sound level at the instrument’s output, and therefore

the total output from all modifier and effect stages.

• The Amplitude parameter affects the level of the sound prior to the VL1 effect

stages, so it can be used to vary the amount of overdrive produced by the

distortion effect, for example (≥ Page 51).

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to amplitude. The

higher the value the greater the variation. Positive values cause an increase in amplitude

in response to higher controller values (e.g. increased breath pressure or higher modula-

tion wheel position), while minus values cause a decrease in amplitude in response to

higher controller values. The “Depth” setting is reflected in the graph to the right of the

parameters — the horizontal axis represents the controller value and the vertical axis

represents amplitude.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and amplitude. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in amplitude. As the curve value increases the lower end of the control-

ler range has relatively little effect on the sound while higher controller values produce

more dramatic changes. Negative curve values have the opposite effect: the sound

changes dramatically at low controller values while higher values produce relatively little

effect. The “Curve” setting is reflected in the graph to the right of the parameters — the

horizontal axis represents the controller value and the vertical axis represents amplitude.

Element Controller

Feature Reference

●

Edit Mode

7: Scream

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Scream” parameter drives the entire system into chaotic oscillation, creating

effects that can only be achieved with physical modeling technology. The “Control-

ler” parameter specifies the controller to be used for scream control. When set to “off”

no scream effect variation can be produced, but an absolute scream value can be set via

the “Value” parameter, below.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to scream. The

higher the value the greater the variation. Positive values cause an increase in scream

effect in response to higher controller values (e.g. increased breath pressure or higher

modulation wheel position), while minus values cause a decrease in screan effect in

response to higher controller values. The “Depth” setting is reflected in the graph to the

right of the parameters — the horizontal axis represents the controller value and the

vertical axis represents scream.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and scream. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in scream effect. As the curve value increases the lower end of the

controller range has relatively little effect on the sound while higher controller values

produce more dramatic changes. Negative curve values have the opposite effect: the

sound changes dramatically at low controller values while higher values produce rela-

tively little effect. The “Curve” setting is reflected in the graph to the right of the

parameters — the horizontal axis represents the controller value and the vertical axis

represents scream.

●

Value

≤ 0 … 127.

Determines the amount of scream effect produced when the “Controller”

parameter is set to “off”. The higher the value the greater the effect.

Feature Reference

●

Edit Mode

8: Breath Noise

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Breath Noise

parameter page (≥ Page 86), also available from the ELEMENT MISCEL-

LANEOUS directory. You can then return to the controller Breath Noise page

by pressing • (“Ctrl”) again.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Breath Noise” parameter can be used to add the required amount of breath

noise to a voice. The sound of the breath noise itself can be varied over a wide range

using the Breath Noise parameters — accessible from this page by pressing the •

button, or from the ELEMENT MISCELLANEOUS directory. The “Controller”

parameter specifies the controller to be used for breath noise control. When set to “off”

no breath noise variation can be produced, but an absolute breath noise value can be set

via the “Value” parameter, below.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to breath noise.

The higher the value the greater the variation. Positive values cause an increase in breath

noise in response to higher controller values (e.g. increased breath pressure or higher

modulation wheel position), while minus values cause a decrease in breath noise in

response to higher controller values. The “Depth” setting is reflected in the graph to the

right of the parameters — the horizontal axis represents the controller value and the

vertical axis represents breath noise.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and breath noise. When set

to “0” the relationship is linear. That is, a change in the controller value produces a

corresponding change in breath noise. As the curve value increases the lower end of the

controller range has relatively little effect on the sound while higher controller values

produce more dramatic changes. Negative curve values have the opposite effect: the

sound changes dramatically at low controller values while higher values produce rela-

Element Controller

Feature Reference

●

Edit Mode

tively little effect. The “Curve” setting is reflected in the graph to the right of the

parameters — the horizontal axis represents the controller value and the vertical axis

represents breath noise.

●

Value

≤ 0 … 127.

Determines the amount of breath noise produced when the “Controller” param-

eter is set to “off”. The higher the value the greater the effect.

• No breath noise can be applied via any controller if the ELEMENT MISCEL-

LANEOUS Breath Noise page “Level” parameter is set to “0” or the “Con-

trol Balance” parameter is set to “63” (≥ Page 86).

9: Growl

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Growl parameter

page (≥ Page 141), also available from the ELEMENT ENVELOPE direc-

tory. You can then return to the controller Growl page by pressing •

(“Ctrl”) again.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Growl” parameter produces a periodic pressure modulation which produces

the “growl” effect often heard in wind instruments. An extensive range of parameters

allow remarkably realistic effects. The “Controller” parameter specifies the controller

to be used for growl control. When set to “off” no growl variation can be produced, but

an absolute growl value can be set via the “Value” parameter, below.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to growl. The

higher the value the greater the variation. Positive values cause an increase in growl

Feature Reference

●

Edit Mode

effect in response to higher controller values (e.g. increased breath pressure or higher

modulation wheel position), while minus values cause a decrease in growl effect in

response to higher controller values. The “Depth” setting is reflected in the graph to the

right of the parameters — the horizontal axis represents the controller value and the

vertical axis represents growl.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and growl. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in growl. As the curve value increases the lower end of the controller

range has relatively little effect on the sound while higher controller values produce more

dramatic changes. Negative curve values have the opposite effect: the sound changes

dramatically at low controller values while higher values produce relatively little effect.

The “Curve” setting is reflected in the graph to the right of the parameters — the

horizontal axis represents the controller value and the vertical axis represents growl.

●

Value

≤ 0 … 127.

Determines the amount of growl effect produced when the “Controller” param-

eter is set to “off”. The higher the value the greater the effect.

• No growl effect can be applied via any controller if the ELEMENT ENVE-

LOPE Growl page “Level” parameter is set to “0” or the “Control Bal-

ance” parameter is set to “63” (≥ Page 141).

10: Throat Formant

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Throat Formant

parameter page (≥ Page 91), also available from the ELEMENT MISCEL-

LANEOUS directory. You can then return to the controller Throat Formant

page by pressing • (“Ctrl”) again.

Element Controller

Feature Reference

●

Edit Mode

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The “Throat Formant” parameter controls the characteristics of the simulated

player’s lungs, trachea, and oral cavity. Can add a realistic “roughness” to the sound.

The “Controller” parameter specifies the controller to be used for throat formant

control. When set to “off” no throat formant variation can be produced, but an absolute

throat formant value can be set via the “Value” parameter, below.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to throat formant.

The higher the value the greater the variation. Positive values cause an increase in throat

formant effect in response to higher controller values (e.g. increased breath pressure or

higher modulation wheel position), while minus values cause a decrease in throat formant

effect in response to higher controller values. The “Depth” setting is reflected in the

graph to the right of the parameters — the horizontal axis represents the controller value

and the vertical axis represents throat formant depth.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and throat formant depth.

When set to “0” the relationship is linear. That is, a change in the controller value

produces a corresponding change in throat formant depth. As the curve value increases

the lower end of the controller range has relatively little effect on the sound while higher

controller values produce more dramatic changes. Negative curve values have the oppo-

site effect: the sound changes dramatically at low controller values while higher values

produce relatively little effect. The “Curve” setting is reflected in the graph to the right

of the parameters — the horizontal axis represents the controller value and the vertical

axis represents throat formant depth.

●

Value

≤ 0 … 127.

Determines the amount of throat formant effect produced when the “Control-

ler” parameter is set to “off”. The higher the value the greater the effect.

• No throat formant effect can be applied via any controller if the ELEMENT

MISCELLANEOUS Throat Formant page “Amount” or “Intensity”

parameters are set to “0” (≥ Page 91, 92).

Feature Reference

●

Edit Mode

11: Dynamic Filter

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Dynamic Filter

parameter page (≥ Page 115), also available from the ELEMENT MODI-

FIER directory. You can then return to the controller Dynamic Filter page by

pressing • (“Ctrl”) again.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The VL1 dynamic filter has selectable high-pass, bandpass, band elimnination, and

low-pass modes. The “Controller” parameter specifies the controller to be used for

filter cutoff frequency control. When set to “off” no filter frequency variation can be

applied via a controller.

• The actual dynamic filter frequency value applied to the VL1 tone generator is

a mix of the value from the controller, the value from the Dynamic Filter

parameter page, and that from the amplitude & filter envelope (≥ Page

143).

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to dynamic filter.

The higher the value the greater the variation. Positive values cause an increase in filter

cutoff frequency in response to higher controller values (e.g. increased breath pressure or

higher modulation wheel position), while minus values cause a decrease in filter cutoff

frequency in response to higher controller values. The “Depth” setting is reflected in the

graph to the right of the parameters — the horizontal axis represents the controller value

and the vertical axis represents filter cutoff frequency.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and dynamic filter cutoff

frequency. When set to “0” the relationship is linear. That is, a change in the controller

value produces a corresponding change in frequency. As the curve value increases the

lower end of the controller range has relatively little effect on the sound while higher

controller values produce more dramatic changes. Negative curve values have the oppo-

Element Controller

Feature Reference

●

Edit Mode

site effect: the sound changes dramatically at low controller values while higher values

produce relatively little effect. The “Curve” setting is reflected in the graph to the right

of the parameters — the horizontal axis represents the controller value and the vertical

axis represents filter cutoff frequency.

• No dynamic filter frequency variation can be applied via any controller if the

ELEMENT MODIFIER Dynamic Filter page “Balance” parameter is set to

“-64” (≥ Page 116).

12: Harmonic Enhancer

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

• The • button (“Para”) can be used to go directly to the Harmonic En-

hancer parameter page (≥ Page 107), also available from the ELEMENT

MODIFIER directory. You can then return to the controller Harmonic En-

hancer page by pressing • (“Ctrl”) again.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The Harmonic Enhancer can vary the harmonic structure of the sound over a wide

range. The “Controller” parameter specifies the controller to be used for harmonic

enhancer depth (wet/dry balance) control. When set to “off” no harmonic enhancer

depth variation can be applied via a controller.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to the harmonic

enhancer. The higher the value the greater the variation. Positive values cause an increase

in harmonic enhancer depth in response to higher controller values (e.g. increased breath

pressure or higher modulation wheel position), while minus values cause a decrease in

harmonic enhancer depth in response to higher controller values. The “Depth” setting is

reflected in the graph to the right of the parameters — the horizontal axis represents the

controller value and the vertical axis represents harmonic enhancer depth depth.

Feature Reference

●

Edit Mode

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and harmonic enhancer

depth. When set to “0” the relationship is linear. That is, a change in the controller value

produces a corresponding change in harmonic enhancer depth. As the curve value in-

creases the lower end of the controller range has relatively little effect on the sound while

higher controller values produce more dramatic changes. Negative curve values have the

opposite effect: the sound changes dramatically at low controller values while higher

values produce relatively little effect. The “Curve” setting is reflected in the graph to

the right of the parameters — the horizontal axis represents the controller value and the

vertical axis represents harmonic enhancer depth.

• No harmonic enhancer variation can be applied via any controller if the

ELEMENT MODIFIER Harmonic Enhancer page “Balance” parameter is

set to “-64” (≥ Page 108).

Element Controller

Feature Reference

●

Edit Mode

13: Damping

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Element Controller page without having to

return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

Simulates the effect of damping due to losses within the body of a wind instrument

or in a string due to air friction. Affects both pitch and timbre. The “Controller”

parameter specifies the controller to be used for damping control. When set to “off” no

damping variation can be applied via a controller.

• Please note that accurate keyboard pitch is produced only when damping is

maximum.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to damping. The

higher the value the greater the variation. Positive values cause a decrease in damping in

response to higher controller values (e.g. increased breath pressure or higher modulation

wheel position), while minus values cause an increase in damping in response to higher

controller values. The “Depth” setting is reflected in the graph to the right of the param-

eters — the horizontal axis represents the controller value and the vertical axis represents

damping.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and damping. When set to

“0” the relationship is linear. That is, a change in the controller value produces a corre-

sponding change in damping. As the curve value increases the lower end of the controller

range has relatively little effect on the sound while higher controller values produce more

dramatic changes. Negative curve values have the opposite effect: the sound changes

dramatically at low controller values while higher values produce relatively little effect.

The “Curve” setting is reflected in the graph to the right of the parameters — the

horizontal axis represents the controller value and the vertical axis represents damping.

Feature Reference

●

Edit Mode

14: Absorption

• The § button (“Bpag”) can be used to go directly back to the next Element

Controller page without having to return to the directory.

●

Controller

≤ off, Modulation Wheel … Touch EG (124 settings).

The absorption parameter simulates the effect of high-frequency loss at the end of

the air column or string. The “Controller” parameter specifies the controller to be

used for absorption control. When set to “off” no absorption variation can be applied

via a controller.

• Please note that accurate keyboard pitch is produced only at when absorption

is maximum.

●

Depth

≤ -127 … 127.

Sets the amount of variation produced by the controller assigned to absorption. The

higher the value the greater the variation. Positive values cause a decrease in absorption

in response to higher controller values (e.g. increased breath pressure or higher modula-

tion wheel position), while minus values cause an increase in absorption in response to

higher controller values. The “Depth” setting is reflected in the graph to the right of the

parameters — the horizontal axis represents the controller value and the vertical axis

represents absorption.

●

Curve

≤ -16 … 16.

Determines the relationship between the controller value and absorption. When set

to “0” the relationship is linear. That is, a change in the controller value produces a

corresponding change in absorption. As the curve value increases the lower end of the

controller range has relatively little effect on the sound while higher controller values

produce more dramatic changes. Negative curve values have the opposite effect: the

sound changes dramatically at low controller values while higher values produce rela-

tively little effect. The “Curve” setting is reflected in the graph to the right of the

parameters — the horizontal axis represents the controller value and the vertical axis

represents absorption.

Element Controller

Feature Reference

●

Edit Mode

Controller Search & Replace

This function is accessed by pressing the • button (“S&R”) from the element

controller directory page. It provides a fast, convenient way to see which controllers are

assigned to which parameters, and to modify the assignments as required.

1. Select the Controller Search & Replace Window

From the element controller directory page, press •.

2. Select a Controller

When the “CONTROLLER SEARCH & REPLACE” window appears, use the §

and ¶ buttons (“Prev” and “Next”) to search through the assigned controllers (unas-

signed controllers are not displayed). All parameters assigned to the selected controller

are displayed below the controller name (or number).

• In this example, only the Pressure parameter is assigned to the Breath Control-

ler:

• In the following example both Embouchure and Pitch are assigned to the Pitch

bend wheel.

3. Make a New Assignment As Required

You can assign a different controller to the parameters shown by using the data dial

or = and - buttons — without cancelling the original assignments. When a

different controller is selected the controller name will flash and any other parameters

assigned to that controller will appear in non-highlighted text.

• Here, for example, the Pitch Bend controller shown in the previous example

has been replaced with the Breath Attack controller, which is current is

asssigned to the Dynamic Filter.

Feature Reference

●

Edit Mode

Element Controller

4. Press [ to Confirm the new Assignment

When you’re satisfied with the new assignment press the [ button. The

controller name will stop flashing and all assigned parameters will appear in highlighted

text (or you can press the ] button to cancel the operation and return to the element

controller directory).

5. Exit When Done

Press the ] button when you’re ready to return to the element controller direc-

tory.

Feature Reference

●

Edit Mode

ELEMENT

CONTROLLER

MODIFIER

ENVELOPE

EDIT MODE

COMMON

EFFECT

MISCELLANEOUS

Element Miscellaneous

■ 1: Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

■ 2: Breath Noise . . . . . . . . . . . . . . . . . . . . . . . . . 86

● 2-1: Breath Noise Level Key Scaling . . . . . . . . 88

● 2-2: Breath Noise HPF Key Scaling . . . . . . . . . 89

● 2-3: Breath Noise LPF Key Scaling . . . . . . . . . . 90

■ 3: Throat Formant . . . . . . . . . . . . . . . . . . . . . . . 91

● 3-1: Throat Formant Pitch Key Scaling . . . . . . 93

● 3-2: Throat Formant Amount Key Scaling . . . . 94

● 3-3: Throat Formant Intensity Key Scaling . . . . 95

● 3-4: Throat Formant HPF Key Scaling . . . . . . . 96

● 3-5: Throat Formant LPF Key Scaling . . . . . . . 97

■ 4: Mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

● 4-1: Mixing Driver Output Key Scaling . . . . . . 100

● 4-2: Mixing Pipe/String Output Key Scaling . . 101

● 4-3: Mixing Tap Output Key Scaling . . . . . . . . 102

● 4-4: Mixing Tap Location Key Scaling . . . . . . 103

■ 5: Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

● 5-1: Total Amplitude Level Key Scaling . . . . . 104

Feature Reference

●

Edit Mode

Element Miscellaneous

1: Setting

●

Trigger Mode

≤ Single, Multi.

Determines how the attack portion of the sound will be triggered.

• The “Single” setting makes it easy to produce the “hammering on” and “pull-

ing off” type effects used by guitar players, for example.

●

Xfade Speed

≤ Fastest, 0.09msec … 390msec.

Simulates the naturally slow note-to-note transitions of acoustic instruments. The

slight “slur” that occurs between notes on wind instruments with tone holes is one exam-

ple. The “Fastest” setting produces the fastest, most synthesizer-like transition be-

tween subsequently-played notes. The higher the value, the longer the transition. Nor-

mally, as setting somewhere between 1 and 2 milliseconds produces the most natural

sound.

●

Interpolate Speed

≤ Fastest, 0.09msec … 6.35msec.

Determines the response time of the VL1 to control changes — Pressure, Embou-

chure, etc. The higher the value the faster the response (e.g. the slower the attack when

pressure is applied). Normally, as setting somewhere between 1 and 2 milliseconds

produces the most natural sound. Decay-type voices sound best a somewhat shorter value.

If a note is played on the keyboard, then a subsequent note or notes

are played while the first key is still held, no attack is produced.

The attack is always reproduced regardless of whether a previous key

is held or not.

Single

Multi

Feature Reference

●

Edit Mode

2: Breath Noise

• The • button (“Ctrl”) can be used to go directly to the breath noise

controller page (≥ Page 73), also available from the ELEMENT CON-

TROLLER directory. You can then return to the miscellaneous breath noise

page by pressing • (“Para”) again.

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the breath noise parameter page by pressing the ]

button.

●

Level

≤ 0 … 127.

Sets the level (volume) of the breath noise sound. The higher the value the higher

the level.

• If this parameter is set to “0”, no breath noise can be applied via a controller.

●

Slit Drive

≤ 0 … 32.

Breath noise is produced at the “slit” portion of the VL1’s physical model (in a reed

instrument, the space between the reed and the mouthpiece). This parameter determines

the intensity of the breath noise. The smaller the value the more intense and rough the

breath noise.

• If this parameter is set to “63”, no breath noise can be applied via a controller.

●

Ctrl Balance

≤ -64 … 63.

Sets the balance between two factors that determine the overall level of the breath

noise: “Ctrl” is the amount of control applied via the controller assigned to breath noise,

and “Slit” is the amount of breath noise produced by the slit. The graphic slider to the

right of the parameter provides a visual indication of the current balance.

Feature Reference

●

Edit Mode

●

HPF Cutoff Frq

≤ 31.1 Hz … 21.6 kHz.

Sets the cutoff frequency of the breath noise high-pass filter. Noise components

below the specified frequency are cut off.

●

LPF Cutoff Frq

≤ 31.1 Hz … 24.0 kHz.

Sets the cutoff frequency of the breath noise low-pass filter. Noise components

above the specified frequency are cut off.

• Virtually no breath noise sound will be produced if the high-pass filter is set

to a higher cutoff frequency than the low-pass filter.

●

Key On Reset

≤ off, on.

Determines the feel of the breath noise attack.

Element Miscellaneous

The noise generator is reset for each note, resulting in the same breath

noise attack feel for each note played.

The noise generator is not reset for each note, result in a different, and

therefore natural, attack feel for each note played.

off

Feature Reference

●

Edit Mode

2-1: Breath Noise Level Key Scalling

Breath noise level key scaling produces natural breath noise level variations across

the range of the keyboard by allowing different level offset values to be applied to each

of six breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly the next breath noise key

scaling page without having to return to the main parameter page.

●

Level

≤ 0 … 127.

The “Level” parameter is linked to the main breath noise “Level” parameter, and

sets the level (volume) of the breath noise sound. The higher the value the higher the

level. This value also determines the main level on which all key-scaled variations are

based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 6 Key

≤ C-2 … G8.

Allows six separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of level offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the level, and positive values increase the

level at the corresponding breakpoint. No matter what offset value is chosen, the actual

level will never exceed its minimum or maximum absolute value. When different offset

values are applied to adjacent breakpoints, the level varies smoothly between the break-

points.

■ If two breakpoints are

set to the same note, the

lower one functions as the

end of the key scaling

segment connecting to the

next lowest breakpoint

while the higher one

functions as the end of the

segment connecting to the

next highest breakpoint.

Further, the higher

breakpoint applies to the

specified note while the

lower one actually applies

to the next note to its left.

If more than two break-

points are set to the same

note, only the lowest and

highest of these will

function as ends of the

corresponding key scaling

segments while the rest

are ignored.

BP3

BP2

BP4

BP1

BP5

C2 C3 C4

NOTES

Feature Reference

●

Edit Mode

2-2: Breath Noise HPF Key Scalling

Element Miscellaneous

Breath noise HPF key scaling produces natural breath noise tone variations across

the range of the keyboard by allowing different cutoff frequency offset values to be

applied to each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next breath noise key scaling page without having

to return to the main parameter page.

●

HPF

≤ 31.1 Hz … 21.6 kHz.

The “HPF” parameter is linked to the main breath noise “HPF Cutoff Frq”

parameter, and sets the cutoff frequency of the breath noise high-pass filter. Noise com-

ponents below the specified frequency are cut off. This value also determines the main

cutoff frequency on which all key-scaled variations are based (indicated by a dotted line

on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Feature Reference

●

Edit Mode

2-3: Breath Noise LPF Key Scalling

Breath noise LPF key scaling produces natural breath noise tone variations across

the range of the keyboard by allowing different cutoff frequency offset values to be

applied to each of two breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly back to the next breath

noise key scaling page without having to return to the main parameter page.

●

LPF

≤ 31.1 Hz … 24.0 kHz.

The “LPF” parameter is linked to the main breath noise “LPF Cutoff Frq”

parameter, and sets the cutoff frequency of the breath noise low-pass filter. Noise compo-

nents above the specified frequency are cut off. This value also determines the main

cutoff frequency on which all key-scaled variations are based (indicated by a dotted line

on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Feature Reference

●

Edit Mode

3: Throat Formant

• The • button (“Ctrl”) can be used to go directly to the throat formant

controller page (≥ Page 75), also available from the ELEMENT CON-

TROLLER directory. You can then return to the miscellaneous throat formant

page by pressing • (“Para”) again.

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the throat formant parameter page by pressing the

] button.

●

Pitch Tracking

≤ Fixed, KeyTrack.

Determines whether the throat formant pitch is fixed or tracks the keyboard.

Element Miscellaneous

The throat formant is fixed at the pitch specified by the “Pitch”

parameter, below.

The pitch of the throat formant tracks the note(s) played on the

keyboard, offset by the amount specified by the “Pitch” parameter,

below.

Fixed

KeyTrack

●

Pitch

≤ 23.1 Hz … 48.0 kHz (when "Fixed" and "Intens"

≥

0).

≤ 11.4 Hz … 24.0 kHz (when "Fixed" and "Intens" < 0).

≤ -2.00oct … 1.98oct (when "KeyTrack").

When the “Pitch Tracking” parameter is set to “Fixed”, this parameter sets

the throat formant pitch to a specific frequency. When “Pitch Tracking” is set to

“KeyTrack”, however, this parameter determines how much the throat formant pitch is

offset from the pitch of the key played in octave units. In the latter case negative values

offset the throat formant pitch below the pitch of the key played, while positive values

offset the throat formant pitch above that of the key played.

●

Amount

≤ -64 … 63.

Determines the amount of effect the throat formant sound has on the air velocity

within the instrument. Positive values increase the air velocity, thereby increasing the

throat formant effect. Minus values decrease the air velocity, producing a more subtle

throat formant effect.

Feature Reference

●

Edit Mode

• If this parameter is set to “0”, no throat formant effect can be applied via a

controller.

●

Intens

≤ -127 … 127.

Sets the intensity of the throat formant effect. Higher values in both the positive and

negative ranges increase the intensity of the throat formant effect.

• If this parameter is set to “0”, no throat formant effect can be applied via a

controller.

●

HPF Cutoff Frq

≤ 31.1 Hz … 21.6 kHz.

Sets the cutoff frequency of the throat formant high-pass filter. Noise components

below the specified frequency are cut off.

●

LPF Cutoff Frq

≤ 31.1 Hz … 24.0 kHz.

Sets the cutoff frequency of the throat formant low-pass filter. Noise components

above the specified frequency are cut off.

• Virtually no throat formant sound will be produced if the high-pass filter is set

to a higher cutoff frequency than the low-pass filter.

Feature Reference

●

Edit Mode

Throat formant pitch key scaling produces natural throat formant pitch variations

across the range of the keyboard by allowing different pitch offset values to be applied to

each of four breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly the next throat formant

key scaling page without having to return to the main parameter page.

●

Pitch

≤ 23.1 Hz … 48.0 kHz (when “Fixed” and “Intens”

≥

0).

≤ 11.4 Hz … 24.0 kHz (when “Fixed” and “Intens” < 0).

≤ -2.00oct … 1.98oct (when “KeyTrack”).

The “Pitch” parameter is linked to the main throat formant “Pitch” parameter,

and has the same effect. When the “Pitch Tracking” parameter is set to “Fixed”,

this parameter sets the throat formant pitch to a specific frequency. When “Pitch

Tracking” is set to “KeyTrack”, however, this parameter determines how much the

throat formant pitch is offset from the pitch of the key played in octave units. In the latter

case negative values offset the throat formant pitch below the pitch of the key played,

while positive values offset the throat formant pitch above that of the key played. This

value also determines the main pitch on which all key-scaled variations are based (indi-

cated by a dotted line on the graph).

●

Breakpoint 1 … 4 Key

≤ C-2 … G8.

Allows four separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 4 Offset

≤ -127 … 127.

Set the amount of pitch offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values lower the pitch, and positive values raise the

pitch at the corresponding breakpoint. No matter what offset value is chosen, the actual

pitch will never exceed its minimum or maximum absolute value. When different offset

values are applied to adjacent breakpoints, the pitch varies smoothly between the break-

points.

3-1: Throat Formant Pitch Key Scalling

Element Miscellaneous

Feature Reference

●

Edit Mode

3-2: Throat Formant Amount Key Scalling

Throat formant amount key scaling produces natural throat formant variations across

the range of the keyboard by allowing different amount offset values to be applied to

each of four breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next throat formant key scaling page without

having to return to the main parameter page.

●

Amount

≤ -64 … 63.

The “Amount” parameter is linked to the main throat formant “Amount” param-

eter, and determines the amount of effect the throat formant sound has on the air velocity

within the instrument. Positive values increase the air velocity, thereby increasing the

throat formant effect. Minus values decrease the air velocity, producing a more subtle

throat formant effect.

This value also determines the main amount value on which all key-scaled variations are

based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 4 Key

≤ C-2 … G8.

Allows four separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 4 Offset

≤ -64 … 63.

Set the amount offset for each of the breakpoints defined by the breakpoint key

parameters, above. Negative values reduce the amount, and positive values increase the

amount at the corresponding breakpoint. No matter what offset value is chosen, the actual

amount will never exceed its minimum or maximum absolute value. When different

offset values are applied to adjacent breakpoints, the amount varies smoothly between the

breakpoints.

Feature Reference

●

Edit Mode

Throat formant intensity key scaling produces natural throat formant intensity

variations across the range of the keyboard by allowing different intensity offset values to

be applied to each of four breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next throat formant key scaling page without

having to return to the main parameter page.

●

Intens

≤ -127 … 127.

The “Intens” parameter is linked to the main throat formant “Intens” param-

eter, and sets the intensity of the throat formant effect. Higher values in both the positive

and negative ranges increase the intensity of the throat formant effect. This value also

determines the main intensity value on which all key-scaled variations are based (indi-

cated by a dotted line on the graph).

●

Breakpoint 1 … 4 Key

≤ C-2 … G8.

Allows four separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 4 Offset

≤ -64 … 63.

Set the amount of intensity offset for each of the breakpoints defined by the break-

point key parameters, above. Negative values reduce the intensity, and positive values

increase the intensity at the corresponding breakpoint. No matter what offset value is

chosen, the actual intensity will never exceed its minimum or maximum absolute value.

When different offset values are applied to adjacent breakpoints, the intensity varies

smoothly between the breakpoints.

3-3: Throat Formant Intensity Key Scalling

Element Miscellaneous

Feature Reference

●

Edit Mode

3-4: Throat Formant HPF Key Scalling

Throat formant HPF key scaling produces natural throat formant tone variations

across the range of the keyboard by allowing different cutoff frequency offset values to

be applied to each of three breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next throat formant key scaling page without

having to return to the main parameter page.

●

HPF

≤ 31.1 Hz … 21.6 kHz.

The “HPF” parameter is linked to the main breath noise “HPF Cutoff Frq”

parameter, and sets the cutoff frequency of the throat formant high-pass filter. Compo-

nents above the specified frequency are cut off. This value also determines the main

cutoff frequency on which all key-scaled variations are based (indicated by a dotted line

on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Feature Reference

●

Edit Mode

3-5: Throat Formant LPF Key Scalling

Throat formant LPF key scaling produces natural throat formant tone variations

across the range of the keyboard by allowing different cutoff frequency offset values to

be applied to each of three breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly back to the next throat

formant key scaling page without having to return to the main parameter page.

●

LPF

≤ 31.1 Hz … 24.0 kHz.

The “LPF” parameter is linked to the main throat formant “LPF Cutoff Frq”

parameter, and sets the cutoff frequency of the throat formant low-pass filter. Compo-

nents above the specified frequency are cut off. This value also determines the main

cutoff frequency on which all key-scaled variations are based (indicated by a dotted line

on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Element Miscellaneous

Feature Reference

●

Edit Mode

4: Mixing

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the mixing parameter page by pressing the ]

button.

●

Driver Output

≤ 0 … 127.

Adjusts the level of the instrument’s “driver” output. The “Driver” signal is the

direct output from the mouthpiece (or bow/string interface) without the resonance of the

instrument’s body. The higher the value the higher the output.

●

Pipe/String Output

≤ 0 … 127.

Adjusts the main output from the instrument’s pipe or string. The higher the value

the higher the output.

●

Tap Output

≤ 0 … 127.

By “tapping” the output from a specific point along the instrument’s pipe or string

and mixing that signal with the Driver and Pipe/String signals, a range of variations can

be produced. This parameter adjusts the tap output. The higher the value the higher the

output.

●

Tap Sign

≤ -, +.

Sets the phase of the tap signal: “+” for positive or normal phase, “-” for negative

or inverse phase.

●

Tap Setting

≤ Variable, Driving Point.

When set to “Driving Point” the tap location is fixed at the instrument’s

driving point (mouthpiece or bow/string interface). When set to “Variable” the tap

location is determined by the “Tap Location” parameter, below.

Feature Reference

●

Edit Mode

●

Tap Location

≤ 0 … 99.2 %.

This parameter only appears when the “Tap Setting” parameter is set to

“Variable”, and is used to set the location of the tap at an appropriate point along the

instrument’s pipe or string.

Element Miscellaneous

Modifiers

Mixing

Pipe/String

Driver

Driver Signal

Pipe/Strings Signal

Tap

Signal

Driver signal to

Harmonic Enhancer

Mixed

Output

100

Feature Reference

●

Edit Mode

4-1: Mixing Driver Output Key Scalling

Mixing driver output key scaling produces natural timbre variations across the range

of the keyboard by allowing different driver output offset values to be applied to each of

six breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly the next throat formant

key scaling page without having to return to the main parameter page.

●

DrivOut

≤ 0 … 127.

The “DrivOut” parameter is linked to the main throat formant “Driver Out-

put” parameter, and has the same effect. This value also determines the main output

level on which all key-scaled variations are based (indicated by a dotted line on the

graph).

●

Breakpoint 1 … 6 Key

≤ C-2 … G8.

Allows six separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of output offset for each of the breakpoints defined by the break-

point key parameters, above. Negative values reduce the output, and positive values

increase the output at the corresponding breakpoint. No matter what offset value is

chosen, the actual output level will never exceed its minimum or maximum absolute

value. When different offset values are applied to adjacent breakpoints, the output varies

smoothly between the breakpoints.

101

Feature Reference

●

Edit Mode

4-2: Mixing Pipe/String Output Key Scalling

Mixing pipe/string output key scaling produces natural timbre variations across the

range of the keyboard by allowing different pipe/string output offset values to be applied

to each of six breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next mixing key scaling page without having to

return to the main parameter page.

●

P/S Out

≤ 0 … 127.

The “P/S Out” parameter is linked to the main mixing “Pipe/String Out-

put” parameter, and has the same effect. This value also determines the main output

level on which all key-scaled variations are based (indicated by a dotted line on the

graph).

●

Breakpoint 1 … 6 Key

≤ C-2 … G8.

Allows six separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of output offset for each of the breakpoints defined by the break-

point key parameters, above. Negative values reduce the output, and positive values

increase the output at the corresponding breakpoint. No matter what offset value is

chosen, the actual output level will never exceed its minimum or maximum absolute

value. When different offset values are applied to adjacent breakpoints, the output varies

smoothly between the breakpoints.

Element Miscellaneous

102

Feature Reference

●

Edit Mode

4-3: Mixing Tap Output Key Scalling

Mixing tap output key scaling produces natural timbre variations across the range of

the keyboard by allowing different tap output offset values to be applied to each of six

breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next mixing key scaling page without having to

return to the main parameter page.

• Tap Output Key Scaling has no effect when the main Mixing page “Tap

Setting” parameter is set to “Driving Position”.

●

TapOut

≤ 0 … 127.

The “TapOut” parameter is linked to the main mixing “Tap Output” parameter,

and has the same effect. This value also determines the main output level on which all

key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 6 Key

≤ C-2 … G8.

Allows six separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of output offset for each of the breakpoints defined by the break-

point key parameters, above. Negative values reduce the output, and positive values

increase the output at the corresponding breakpoint. No matter what offset value is

chosen, the actual output level will never exceed its minimum or maximum absolute

value. When different offset values are applied to adjacent breakpoints, the output varies

smoothly between the breakpoints.

103

Feature Reference

●

Edit Mode

4-4: Mixing Tap Location Key Scalling

Mixing tap location key scaling produces natural timbre variations across the range

of the keyboard by allowing different tap location offset values to be applied to each of

six breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly back to the next mixing

key scaling page without having to return to the main parameter page.

• Tap Location Key Scaling has no effect when the main Mixing page “Tap

Setting” parameter is set to “Driving Position”.

●

TapLoc

≤ 0 … 127.

The “TapLoc” parameter is linked to the main mixing “Tap Location” param-

eter, and has the same effect. This value also determines the main tap location on which

all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 6 Key

≤ C-2 … G8.

Allows six separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of tap location offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the tap location value, and

positive values increase the tap location value at the corresponding breakpoint. No matter

what offset value is chosen, the actual tap location will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the tap location varies smoothly between the breakpoints.

Element Miscellaneous

104

Feature Reference

●

Edit Mode

5: Amplitude

• Key scaling can be applied to the Total Amplitude Level parameter. Press the

¶ button (“KSC”) to go directly to the key scaling page. You can return to

the amplitude parameter page by pressing the ] button.

●

Total Amplitude Level

≤ 0 … 127.

Sets the final output level of the selected Element, after mixing. The higher the

value the higher the level.

5-1: Total Amplitude Level Key Scaling

Total amplitude level key scaling produces natural level variations across the range

of the keyboard by allowing different level offset values to be applied to each of eight

breakpoints set at appropriate keys.

• The ¶ button (“Xfd”) can be used to invert the curve of the Amplitude Key

Scaling for the other element when a 2-element voice is being edited to

produce a crossfade key scaling effect between elements (“Xfd” will not

appear when a 1-element voice is edited).

●

Level

≤ 0 … 127.

The “Level” parameter is linked to the main amplitude “Total Amplitude

Level” parameter, and sets the final output level of the selected Element, after mixing.

The higher the value the higher the level. This value also determines the main level on

which all key-scaled variations are based (indicated by a dotted line on the graph).

105

Feature Reference

●

Edit Mode

●

Breakpoint 1 … 8 Key

≤ C-2 … G8.

Allows eight separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

(indicated by a dotted line on the graph).

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 6 Offset

≤ -64 … 63.

Set the amount of level offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the level, and positive values increase the

level at the corresponding breakpoint. No matter what offset value is chosen, the actual

level will never exceed its minimum or maximum absolute value. When different offset

values are applied to adjacent breakpoints, the level varies smoothly between the break-

points.

Element Miscellaneous

106

Feature Reference

●

Edit Mode

Element Modifier

ELEMENT

EFFECT

ENVELOPE

MISCELLANEOUS

EDIT MODE

COMMON

MISCELLANEOUS

CONTROLLER

MODIFIER

■ 1: Harmonic Enhancer . . . . . . . . . . . . . . . . . . . 107

● 1-1: Harmonic Enhancer HPF Key Scaling . . . 110

● 1-2: Harmonic Enhancer

Overdrive Key Scaling

111

● 1-3: Harmonic Enhancer Carrier Level Key

Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 112

● 1-4: Harmonic Enhancer Modulator Index Key

Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 113

● 1-5: Harmonic Enhancer Balance Key Scaling 114

■ 2: Dynamic Filter . . . . . . . . . . . . . . . . . . . . . . . 115

● 2-1: Dynamic Filter Cutoff Key Scaling . . . . . . 117

● 2-2: Dynamic Filter Resonance Key Scaling . . 118

■ 3: Equalizer Auxiliary . . . . . . . . . . . . . . . . . . . . 119

● 3-1: Equalizer Auxiliary HPF Key Scaling . . . . 120

● 3-2: Equalizer Auxiliary LPF Key Scaling . . . . 121

■ 4: Equlizer Band . . . . . . . . . . . . . . . . . . . . . . . . 122

■ 5: Impulse Expander & Resonator Setting . . . 123

■ 6: Impulse Expander . . . . . . . . . . . . . . . . . . . . 125

■ 7: Resonator . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

107

Feature Reference

●

Edit Mode

Element Modifier

1: Harmonic Enhancer

• The Harmonic Enhancer has both a “Carrier” and “Modulator” block, as

shown in the block diagram below. Each has its own parameters and therefore

two separate parameter pages are provided. Press the ¡ button (“Crr”) to

select the carrier parameter page or ™ (“Mod”) to select the modulator

parameter page.

• The • button (“Ctrl”) can be used to go directly to the harmonic enhancer

controller page (≥ Page 78), also available from the ELEMENT CON-

TROLLER directory. You can then return to the modifier harmonic enhancer

page by pressing • (“Para”) again.

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the harmonic enhancer parameter page by pressing the

] button.

■ Carrier Parameters

■ Modulator Parameters

Driver,

pipe/string,

and tap sound.

Modulator

Source.

Carrier

Source.

Out

(to Dynamic Filter.)

Wet/Dry

Balance

Modulator

Carrier

108

Feature Reference

●

Edit Mode

●

Signal Select

≤ Normal, Breath Noise Amp., Flow Rate Saturation, Beat, Slit/Friction, Reed.

Selects the signal to be used by the carrier or modulator.

This is the total output of the instrument model: a mix of the driver,

pipe/string, and tap signals.

This signal represents the instantaneous amplitude of the breath noise

produced at the driver. It is basically a highly distortion version of the

Slit/Friction signal described below.

When the pressures on either side of an aperture (e.g. a mounthpiece/

reed assembly) differ, a corresponding flow of air is produced. There is,

however, a limit to the speed of the airflow which can be produced

(saturation). The relationship between the pressure difference and

resulting airflow is derived as the Flow Rate Saturation signal.

The beat signal represents contact between the vibrating reed and the

mouthpiece.

As the reed vibrates, the area of gap (slit) between it and the mouth-

piece varies accordingly. The Slit/Friction signal corresponds to the

varying are of the reed/mouthpiece slit.

This signal is derived directly from the flexing of the reed.

Normal

Breath Noise

Amplitude

Flow Rate Satura-

tion

Beat

Slit/Friction

Reed

●

HPF Cutoff

≤ 17.0 Hz … 11.2 kHz.

Both the modulator and carrier blocks have high-pass filters that can be used to roll

off the low frequencies of the corresponding signal. This parameter sets the cutoff fre-

quency of the carrier or modulator high-pass filter.

●

Over Drive

≤ 0.063 … 15.31.

This parameter boosts the corresponding modulator or carrier signal, forcing it into

distortion and thereby drastically changing its harmonic structure. The higher the value

the greater the distortion. No distortion is produced below a setting of “1.0”.

●

Level (Carrier only)

≤ 0 … 127.

Sets the output level of the carrier. The higher the value the greater the output level.

●

Balance

≤ -64 … 63.

Sets the balance between the “wet” (the output of the harmonic enhancer) and “dry”

(the direct signal) signals. The higher the value the more “wet” the signal, and therefore

the more pronounced the harmonic enhancer effect. The carrier and modulator page

“Balance” parameters are linked.

109

Feature Reference

●

Edit Mode

●

Phase (Modulator only)

≤ 0deg … 360deg.

This parameter is provided for the modulator block only. It allows a degree of

timbral variation by varying the phase of the modulator signal through 360 degrees in 2-

or 3-degree increments.

●

Index (Modulator only)

≤ 0 … 127.

Determines how much modulation is applied to the carrier signal (i.e. the level of

the modulator signal applied to the carrier). The higher the value the greater the modula-

tion.

Notes On Using the Harmonic Enhancer

Although any modulator source signal can be applied to any carrier

source signal, two approaches are recommended when attempting to create

an acoustic instrument simulation.

The first is to set the carrier signal to “Normal” and the modulator

signal to any other than normal, set the dry/wet “Balance” to 63 (all wet),

and set a relatively high “Index” value. In this case the total output of the

instrument model (“Normal” signal) will by modulated by one of the

component signals, so the dry/wet “Balance” can be set to fully wet

(carrier output only) since the carrier source and dry signals are essentially

the same. The Index parameter determines how much modulation is

applied, so a higher value is generally required to create sufficient variation.

The second approach is to set the carrier signal to any other than

normal and the modulator signal to any of the six possibilities, set the dry/

wet “Balance” to a more central value, and set a relatively low “Index”

value. In this situation it is necessary to set the “Balance” more toward

the “Dry” side since the carrier source signal is

not the normal signal and

at least some of the dry signal is necessary to provide the basic sound of

the instrument model. In other words, the sound produced by the Harmonic

Enhancer is simply added to the basic sound of the instrument, in contrast

with the first approach in which the basic sound of the instrument is modu-

lated directly.

Please note that these are only guidelines, and are by no means the

only way to work with the Harmonic Enhancer. Since the Harmonic En-

hancer tends to respond differently with different instrument models,

experimentation and experience are your most valuable tools.

Element Modifier

110

Feature Reference

●

Edit Mode

Harmonic Enhancer HPF key scaling produces natural timbral variations across the

range of the keyboard by allowing different cutoff frequency offset values to be applied

to each of two breakpoints set at appropriate keys. Key scaling can be applied independ-

ently to the carrier and modulator high-pass filters.

• Separate key scaling parameter pages are provided for the carrier and modula-

tor high-pass filters. The appropriate key scaling page will be selected when

you press ¶ (“KSC”) from the main carrier or modulator parameter page.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next harmonic enhancer key scaling page without

having to return to the main parameter page.

●

CrrHPF, ModHPF

≤ 17.0 Hz … 11.2 kHz.

The “CrrHPF” and “ModHPF” parameters are linked to the main harmonic en-

hancer “HPF Cutoff” parameters, and set the cutoff frequency of the carrier or modu-

lator high-pass filter. Frequency components below the specified frequency are cut off.

This value also determines the main cutoff frequency on which all key-scaled variations

are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

1-1: Harmonic Enhancer HPF Key Scaling

■ If two breakpoints are

set to the same note, the

lower one functions as the

end of the key scaling

segment connecting to the

next lowest breakpoint

while the higher one

functions as the end of the

segment connecting to the

next highest breakpoint.

BP3

BP2

BP4

BP1

BP5

C2 C3 C4

NOTES

■ Carrier Parameters

■ Modulator Parameters

111

Feature Reference

●

Edit Mode

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

1-2: Harmonic Enhancer Overdrive Key Scaling

Harmonic Enhancer overdrive key scaling produces natural timbral variations across

the range of the keyboard by allowing different overdrive offset values to be applied to

each of two breakpoints set at appropriate keys. Key scaling can be applied independently

to the carrier and modulator overdrive parameters.

• Separate key scaling parameter pages are provided for the carrier and modula-

tor overdrive parameters. The appropriate key scaling page will be selected

when you press ¶ (“KSC”) from the main carrier or modulator parameter

page.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next harmonic enhancer key scaling page without

having to return to the main parameter page.

●

CrrOvr, ModOvr

≤ 0.063 … 15.31 kHz.

The “CrrOvr” and “ModOvr” parameters are linked to the main harmonic en-

hancer “Over Drive” parameters, and set the amount of distortion produced by the

carrier or modulator. This value also determines the main overdrive level on which all

key-scaled variations are based (indicated by a dotted line on the graph).

Element Modifier

■ Carrier Parameters

■ Modulator Parameters

Further, the higher

breakpoint applies to the

specified note while the

lower one actually applies

to the next note to its left.

If more than two break-

points are set to the same

note, only the lowest and

highest of these will

function as ends of the

corresponding key scaling

segments while the rest

are ignored.

112

Feature Reference

●

Edit Mode

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of overdrive offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the overdrive level, and

positive values increase the overdrive level at the corresponding breakpoint. No matter

what offset value is chosen, the actual overdrive level will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the overdrive level varies smoothly between the breakpoints.

1-3: Harmonic Enhancer Carrier Level Key Scaling

Harmonic Enhancer carrier level key scaling produces natural timbral variations

across the range of the keyboard by allowing different carrier level offset values to be

applied to each of four breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next harmonic enhancer key scaling page without

having to return to the main parameter page.

●

CrrLvl

≤ 0 … 127.

The “CrrLvl” parameter is linked to the main harmonic enhancer carrier “Level”

parameter, and sets the output level of the carrier block. This value also determines the

main carrier level on which all key-scaled variations are based (indicated by a dotted line

on the graph).

●

Breakpoint 1 … 4 Key

≤ C-2 … G8.

Allows four separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

113

Feature Reference

●

Edit Mode

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 4 Offset

≤ -64 … 63.

Set the amount of level offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the carrier level, and positive values

increase the carie level at the corresponding breakpoint. No matter what offset value is

chosen, the actual carrier level will never exceed its minimum or maximum absolute

value. When different offset values are applied to adjacent breakpoints, the carrier level

varies smoothly between the breakpoints.

Element Modifier

1-4: Harmonic Enhancer Modulator Index Key Scaling

Harmonic Enhancer modulator index key scaling produces natural timbral variations

across the range of the keyboard by allowing different modulator index offset values to

be applied to each of four breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next harmonic enhancer key scaling page without

having to return to the main parameter page.

●

ModIdx

≤ 0 … 127.

The “ModIdx” parameter is linked to the main harmonic enhancer modulator

“Index” parameter, and sets the amount of modulation applied to the carrier. This value

also determines the main modulator index on which all key-scaled variations are based

(indicated by a dotted line on the graph).

●

Breakpoint 1 … 4 Key

≤ C-2 … G8.

Allows four separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

114

Feature Reference

●

Edit Mode

●

Breakpoint 1 … 4 Offset

≤ -64 … 63.

Set the amount of modulator index offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the modulator index, and

positive values increase the modulator index at the corresponding breakpoint. No matter

what offset value is chosen, the actual modulator index will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the modulator index varies smoothly between the breakpoints.

1-5: Harmonic Enhancer Balance Key Scaling

Harmonic Enhancer balance key scaling produces natural timbral variations across

the range of the keyboard by allowing different balance offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly backward to the next

harmonic enhancer key scaling page without having to return to the main

parameter page.

●

Balance

≤ -64 … 63.

The “Balance” parameter is linked to the main harmonic enhancer “Balance”

parameter, and sets the balance between the wet and dry sound. This value also deter-

mines the main balance value on which all key-scaled variations are based (indicated by a

dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of balance offset for each of the breakpoints defined by the break-

point key parameters, above. Negative values reduce the balance value (toward “dry”),

115

Feature Reference

●

Edit Mode

and positive values increase the balance value (toward “wet”) at the corresponding

breakpoint. No matter what offset value is chosen, the actual balance setting will never

exceed its minimum or maximum absolute value. When different offset values are applied

to adjacent breakpoints, the balance varies smoothly between the breakpoints.

2: Dynamic Filter

• The • button (“Ctrl”) can be used to go directly to the dynamic filter

controller page (≥ Page 77), also available from the ELEMENT CON-

TROLLER directory. You can then return to the modifier dynamic filter page

by pressing • (“Para”) again.

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the dynamic filter parameter page by pressing the

] button.

Element Modifier

●

Filter Mode

≤ LPF, BPF, HPF, BEF.

Selects the filter mode.

Low-pass filter. Frequencies below the cutoff frequency are passed

while those above are cut off. The cutoff slope is -12 dB/octave.

Band-pass filter. In this case the “cutoff frequency” is actually the

center frequency of a narrow band of frequencies which will be passed.

The cutoff slope is -6 dB/octave.

High-pass filter. Frequencies above the cutoff frequency are passed

while those below are cut off. The cutoff slope is -12 dB/octave.

Band-eliminaton filter. The cutoff frequency is the center frequency of a

narrow band of frequencies which will be cut off. The cutoff slope is -6

dB/octave.

LPF

BPF

HPF

BEF

(from Harmonic

Enhancer)

Out

(to Frequency

Equalizer)

Dynamic

Filter

Wet/Dry

Balance

116

Feature Reference

●

Edit Mode

●

Input Gain

≤ 0 … 127.

Adjusts the level of the input signal to the dynamic filter stage. The higher the value

the higher the input level.

●

Balance

≤ -64 … 63.

Sets the balance between the “wet” (the output of the dynamic filter) and “dry”

(direct) signals. The higher the value the more “wet” the signal, and therefore the more

pronounced the dynamic filter effect.

●

Cutoff Tracking

≤ Fixed, KeyTrack.

Determines whether the dynamic filter cutoff frequency is fixed or tracks the

keyboard.

●

Cutoff Freq.

≤ 26.9 Hz … 11.9 kHz (when “Fixed”).

≤ -4.00oct … 3.94oct (when “KeyTrack”).

When the “Cutoff Tracking” parameter is set to “Fixed”, this parameter sets

the dynamic filter cutoff frequency to a specific frequency between 26.9 hertz and 11.9

kilohertz. When “Cutoff Tracking” is set to “KeyTrack”, however, this parameter

determines how much the cutoff frequency is offset from the frequency of the key played

in octave units. In the latter case negative values offset the cutoff frequency below the

frequency of the key played, while positive values offset the cutoff frequency above that

of the key played.

●

Resonance

≤ 1.00 … 15.67.

This parameter produces a “peaking” effect at the filter’s cutoff frequency, further

emphasizing the frequencies at that point. This higher the value the higher the resonant

peak.

The dynamic filter is fixed at the frequency specified by the “Cutoff

Freq.” parameter, below.

The cutoff frequency of the dynamic filter tracks the note(s) played on

the keyboard, offset by the amount specified by the “Cutoff Freq.”

parameter, below.

Fixed

KeyTrack

117

Feature Reference

●

Edit Mode

2-1: Dynamic Filter Cutoff Key Scaling

Dynamic filter cutoff frequency key scaling produces natural timbral variations

across the range of the keyboard by allowing different cutoff frequency offset values to

be applied to each of three breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly forward to the next dynamic

filter key scaling page without having to return to the main parameter page.

●

Cutoff

≤ 26.9 Hz … 11.9 kHz (when “Fixed”).

≤ -4.0oct … 3.94oct (when “KeyTrack”).

The “Cutoff” parameter is linked to the main dynamic filter “Cutoff Freq.”

parameter, and has the same effect. This value also determines the main cutoff frequency

on which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Element Modifier

118

Feature Reference

●

Edit Mode

2-2: Dynamic Filter Resonance Key Scaling

Dynamic filter resonance key scaling produces natural timbral variations across the

range of the keyboard by allowing different resonance offset values to be applied to each

of three breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly backward to the next

dynaic filter key scaling page without having to return to the main parameter

page.

●

Rez

≤ 1.00 … 15.67.

The “Rez” parameter is linked to the main dynamic filter “Resonance” param-

eter, and has the same effect. This value also determines the main resonance value on

which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of resonance offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the resonance, and positive

values increase the resonance at the corresponding breakpoint. No matter what offset

value is chosen, the actual resonance setting will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

resonance varies smoothly between the breakpoints.

119

Feature Reference

●

Edit Mode

3: Equalizer Auxiliary

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the equalizer auxiliary parameter page by pressing the

] button.

●

Input Gain

≤ 0 … 127.

Adjusts the level of the input signal to the equalizer stage. The higher the value the

higher the input level.

●

HPF Cutoff Freq.

≤ 17.0 Hz … 11.2 kHz.

Sets the cutoff frequency of the high-pass filter. Frequency components below the

specified frequency are cut off.

●

LPF Cutoff Freq.

≤ 31.1 Hz … 24.0 kHz.

Sets the cutoff frequency of the low-pass filter. Frequency components above the

specified frequency are cut off. The low-pass filter is completely bypassed when set to

“off”.

Element Modifier

120

Feature Reference

●

Edit Mode

3-1: Equalizer Auxiliary HPF Key Scaling

Equalizer HPF key scaling produces natural tone variations across the range of the

keyboard by allowing different cutoff frequency offset values to be applied to each of

three breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly forward to the next

equalizer auxiliary key scaling page without having to return to the main

parameter page.

●

HPF

≤ 17.0 Hz … 11.2 kHz.

The “HPF” parameter is linked to the main equalizer auxiliary “HPF Cutoff

Freq.” parameter, and sets the cutoff frequency of the high-pass filter. Frequency

components below the specified frequency are cut off. This value also determines the

main cutoff frequency on which all key-scaled variations are based (indicated by a dotted

line on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

121

Feature Reference

●

Edit Mode

3-2: Equalizer Auxiliary LPF Key Scaling

Equalizer LPF key scaling produces natural tone variations across the range of the

keyboard by allowing different cutoff frequency offset values to be applied to each of

three breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly backward to the next

equalizer auxiliary key scaling page without having to return to the main

parameter page.

●

LPF

≤ 31.1 Hz … 24.0 kHz.

The “LPF” parameter is linked to the main equalizer auxiliary “LPF Cutoff

Freq.” parameter, and sets the cutoff frequency of the low-pass filter. Frequency

components above the specified frequency are cut off. This value also determines the

main cutoff frequency on which all key-scaled variations are based (indicated by a dotted

line on the graph).

●

Breakpoint 1 … 3 Key

≤ C-2 … G8.

Allows three separate key scaling breakpoints to be set at any notes between C-2

and G8. You can position the cursor at the appropriate breakpoint key parameter and use

any of the normal data entry procedures, or use the keyboard. To use the keyboard for

breakpoint entry, position the cursor at the appropriate breakpoint key parameter, press

the • button (“Kbd”), and then press the key at which you want to set the breakpoint

while “Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 … 3 Offset

≤ -64 … 63.

Set the amount of cutoff frequency offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values lower the cutoff frequency, and

positive values raise the cutoff frequency at the corresponding breakpoint. No matter

what offset value is chosen, the actual cutoff frequency will never exceed its minimum or

maximum absolute value. When different offset values are applied to adjacent break-

points, the cutoff frequency varies smoothly between the breakpoints.

Element Modifier

122

Feature Reference

●

Edit Mode

4: Equalizer Band

• The Equalizer Band block is a 5-band parametric equalizer with frequency, Q

(bandwidth), and level control. The Band block functions in the same way as

any standard parametric equalizer, allowing flexible response control over a

wide range.

●

Bnd1 Freq

≤ 40.0 Hz … 321.0 Hz.

●

Bnd2 Freq

≤ 104.0 Hz … 838.0 Hz.

●

Bnd3 Freq

≤ 284.0 Hz … 2.00 kHz.

●

Bnd4 Freq

≤ 646.0 Hz … 5.21 kHz.

●

Bnd5 Freq

≤ 1.54 kHz … 10.0 kHz.

These parameters individually set the center frequencies of the equalizer stage’s five

bands. Note that the bands overlap somewhat for smooth, seamless control.

●

Bnd1 … Bnd5 Q

≤ 0.5 … 20.0.

Individually set the Q (bandwidth) for each of the equalizer’s five bands. The higher

the value the narrower the bandwidth.

●

Bnd1 … Bnd5 Level

≤ -24.0 … 23.6.

Individually set the level of the equalizer’s five bands. Negative values produce a

cut at the frequency of the corresponding band while positive values produce a boost.

123

Feature Reference

●

Edit Mode

5: Impulse Expander & Resonator Setting

• This page provide access to a range of parameters which affect operation of

the Impulse Expander and Resonator stages (described later) and how they

interact. It contains a number of parameters which are accessed by moving the

cursor to the appropriate block within the diagram. The corresponding

paramameter will appear in the upper right area of the display.

Element Modifier

Ipulse

Expander

On/Off

Resonator

Input Gain

Resonator

On/Off

Resonator

Wet Level

Resonator

Level

Balance

Dry

Level

Impulse

Expander

Wet Level

Impulse

Expander

Level

Balance

• When the cursor is positioned at the “IE on/off” or “RSN on/off”

block, “Para” will appear above the • button. Press this button to go

directly to the main Impulse Expander (≥ Page 125) or Resonator (≥

Page 126) parameter page, respectively.

●

≤ off, on.

Turns the Impulse Expander stage off or on. When off (and the Resonator, below, is

on) the display will appear as shown below. Only parameters which appear in the dia-

gram are available for editing.

124

Feature Reference

●

Edit Mode

●

RSN

≤ off, on.

Turns the Resonator stage off or on. When off (and the Impulse Expander, above, is

on) the display will appear as shown below. Only parameters which appear in the dia-

gram are available for editing.

●

Dry Level

≤ 0 … 127.

Sets the level of the dry signal (i.e. the direct signal which does not pass through

either the Impulse Expander or the Resonator.

●

IE Wet Level

≤ 0 … 127.

Sets the “wet” output level from the Impulse Expander. The higher the value the

higher the Impulse Expander level.

●

IE Level Bal

≤ -64 … 63.

Adjusts the left-right balance of the wet Impulse Expander signal returned to the

stereo signal path. Positive values route more signal to the right channel while negative

values route more signal to the left channel.

●

RSN Inp Gain

≤ 0 … 127.

Sets the level of the Impulse Expander output signal received at the input of the

Resonator stage. The higher the value the higher the input level.

●

RSN Wet Level

≤ 0 … 127.

Sets the “wet” output level from the Resonator. The higher the value the higher the

Resonator level.

●

RSN Level Bal

≤ -64 … 63.

Adjusts the left-right balance of the wet Resonator signal returned to the stereo

signal path. Positive values route more signal to the right channel while negative values

route more signal to the left channel.

125

Feature Reference

●

Edit Mode

6: Impulse Expander

• This display will not appear — “Impulse Expander is not used”

will appear — if the “IE on/off” block in the “Impulse Expander &

Resonator Setting” page is turned “off” (≥ Page 123). All level and

balance settings relating to the Impulse Expander are also available in that

display page.

• Press the • button (“Set”) to go directly to the “Impulse Expander & Reso-

nator Setting” page.

The Impulse Expander works in conjunction with the Resonator, described below, to

simulate the effect of an instrument’s resonant cavity or sound box. It can also be used to

simulate the acoustic environment in which the instrument is played.

●

Density

≤ 0.146 msec … 20.77 msec.

Adjusts the density of the sound, and therefore its texture. Higher values produce

greater density.

●

Dispersion

≤ 4.028 msec … 4.000 sec.

Determines the resonance time. The higher the value the longer the resonance.

• A high dispersion setting produces an early-reflections type reverberation effect.

●

Roughness

≤ 0 … 16.

This parameter imparts a “roughness” to the overall frequency response in the form

of steep peaks and dips in the response. The higher the value the greater the roughness.

Element Modifier

Mix

Frequency-dependent Delay

(from Frequency

Equalizer)

Out

(to Resonator)

126

Feature Reference

●

Edit Mode

7: Resonator

• This display will not appear — “Resonator is not used” will appear

— if the “RES on/off” block in the “Impulse Expander & Resonator

Setting” page is turned “off” (≥ Page 124). All level and balance settings

relating to the Resonator are also available in that display page.

• Press the • button (“Set”) to go directly to the “Impulse Expander & Reso-

nator Setting” page.

While the Impulse Expander tends to give the sound a metallic quality, the Resona-

tor produces a more woody resonance effect. Careful adjustment of the resonator’s

parameters can often bring a not-quite-right voice to life.

●

DL1 … DL5

≤ 0.29 msec … 41.54 msec.

These parameters independently set the delay times for the Resonator’s five delay

lines.

Delay times for “natural” effects can be calculated by dividing the instrument’s

body dimensions by the speed of sound (34 centimeters per millisecond). for example, an

instrument with a body which measures 68 cm x 34 cm would naturally include delay

times of 2 msec (68/34 = 2 msec) and 1 msec (34/34 = 1 msec. These values can then be

fine-adjusted to achieve the desired results.

Right Channel

Left Channel

Out (to Effects)

(from Resonator)

Delay

127

Feature Reference

●

Edit Mode

Element Modifier

●

Decay Time

≤ 4,028 msec … 4.000 sec.

Determines the length of decay of the sound. The higher the value the longer the

decay.

●

LPF Cutoff Freq.

≤ 31.1 Hz … 24.0 kHz.

Sets the cutoff frequency of the low-pass filter. Produces a natural decay in the

high-frequency components of the delay sound.

●

Diffusion

≤ 0 … 16.

Determines how the resonance sound “spreads” in the stereo sound field. The higher

the value the wider the sound.

●

Phase

≤ -16 … 16.

Sets the phase of the resonance signal, changing its position in the stereo sound

field. Positive values move the resonance sound to the left wile negative values move it

to the right.

128

Feature Reference

●

Edit Mode

Element Envelope

ELEMENT

EFFECT

MISCELLANEOUS

EDIT MODE

COMMON

MISCELLANEOUS

CONTROLLER

MODIFIER

ENVELOPE

■ 1: Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

■ 2: Embouchure & Pitch . . . . . . . . . . . . . . . . . . 130

● 2-1:

Embouchure & Pitch Hold Time Key Scaling

132

● 2-2:

Embouchure & Pitch Initial Level Key Scaling

133

● 2-3:

Embouchure & Pitch Decay Rate Key Scaling

134

■ 3: Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

● 3-1: Vibrato Delay Time Key Scaling . . . . . . . 137

● 3-2: Vibrato Attack Rate Key Scaling . . . . . . . 138

● 3-3: Vibrato Depth Key Scaling . . . . . . . . . . . 139

● 3-4: Vibrato Speed Key Scaling . . . . . . . . . . . 140

■ 4: Growl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

● 4-1: Growl Speed Key Scaling . . . . . . . . . . . . . . . 142

■ 5: Amplitude & Filter . . . . . . . . . . . . . . . . . . . . . . 143

● 5-1:

Amplitude & Filter Attack Rate Key Scaling

. . 146

● 5-2:

Amplitude & Filter Attack 1 Level Key Scaling

147

● 5-3: Amplitude & Filter Decay Rate Key Scaling . 148

● 5-4: Amplitude & Filter Sustain Level Key Scaling 149

● 5-5: Amplitude & Filter Release Rate Key Scaling 150

129

Feature Reference

●

Edit Mode

Element Envelope

1: Pressure

• Each VL1 voice has its own pressure envelope which determines how it

responds to pressure changes. The parameters in this display page determine

how the pressure envelope is used and how it will respond to keyboard veloc-

ity.

●

EG Mode

≤ Disable, ADSR, AR.

This parameter determines whether or how the pressure envelope will be used.

●

Attack Rate Offset

≤ -16 … 16.

Adjusts the attack rate of the voice’s pressure evelope. Positive values produce a

faster attack while negative values produce a slower attack.

●

Release Rate Offset

≤ -16 … 16.

Adjusts the release rate of the voice’s pressure evelope. Positive values produce a

faster release while negative values produce a slower release.

●

Velocity Sens To Level

≤ 0 … 16.

Determines the relationship between pressure and keyboard velocity. When set to

“0”, keyboard velocity (i.e. how fast or hard the keyboard is played) has no effect on

pressure. At values higher than “1”, however, high keyboard velocities will increase the

pressure and low keyboard velocities will decrease the pressure. The higher the value the

greater the effect of keyboard velocity on pressure.

The voice’s pressure envelope is not used, and pressure always

corresponds exactly to the position or value of the controller assigned

to pressure. If no controller is assigned the pressure is always maxi-

mum. In this case the “Attack Rate Offset”, “Release Rate

Offset”, “Velocity Sens To Level”, and “Velocity Sens To

Rate” parameters have no effect.

Pressure responds according to the attack, decay, sustain, and release

settings of the voice’s pressure envelope.

Pressure responds according to the attack and release settings of the

voice’s pressure envelope. The decay and sustain settings are ignored.

Disable

ADSR

130

Feature Reference

●

Edit Mode

●

Velocity Sens To Rate

≤ 0 … 16.

Determines the relationship between the voice’s pressure envelope rates (attack,

decay, and release) and keyboard velocity. When set to “0”, keyboard velocity (i.e. how

fast or hard the keyboard is played) has no effect on the envelope rates. At values higher

than “1”, however, high keyboard velocities will increase the rates and low keyboard

velocities will decrease the rates. The higher the value the greater the effect of keyboard

velocity on the pressure envelope rates.

2: Embouchure & Pitch

• Each VL1 voice has its own embouchure & pitch envelope which determines

how it responds to embouchure and pitch changes. The parameters in this

display page determine how the embouchure & pitch envelope is used and

how it will respond to keyboard velocity.

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the embouchure & pitch envelope parameter page by

pressing the ] button.

●

VlSns To Lvl

≤ 0 … 16.

Determines the relationship between embouchure/pitch and keyboard velocity.

When set to “0”, keyboard velocity (i.e. how fast or hard the keyboard is played) has no

effect on embouchure or pitch. At values higher than “1”, however, high keyboard

velocities produce a higher embouchure and pitch variation while low keyboard velocities

produce a smaller variation. The higher the value the greater the effect of keyboard

velocity on embouchure & pitch.

●

VlSns To Rate

≤ -16 … 16.

Determines the relationship between the voice’s embouchure & pitch envelope

decay rate and keyboard velocity. When set to “0”, keyboard velocity (i.e. how fast or

hard the keyboard is played) has no effect on the decay rate. At values higher than “1”,

131

Feature Reference

●

Edit Mode

however, high keyboard velocities will increase the decay rate and low keyboard veloci-

ties will decrease the decay rate. Negative values have the opposite effect. The higher the

value the greater the effect of keyboard velocity on the embouchure & pitch envelope

decay rate.

●

Dpth To Emb

≤ 0 … 64.

This parameter determines how deeply the settings in this display page affect

embouchure. The higher the value the greater the effect.

●

Dpth To Ptch

≤ 0 … 64.

This parameter determines how deeply the settings in this display page affect pitch.

The higher the value the greater the effect.

●

Hold Time

≤ 0 … 127.

Sets the hold time of the embouchure & pitch envelope. That is, the length of time

the initial envelope level is held before the decay portion of the envelope begins (see

“Initial Lvl”, below). The higher the value the longer the hold time.

Element Envelope

●

Initial Lvl

≤ -64 … 63.

Sets the initial level of the embouchure & pitch envelope. That is, the level of the

envelope (pitch in the case of the pitch parameter) at the instant a key is played. The

higher the value the higher the initial level.

• If the “Initial Lvl” parameter is set to “0” the embouchure & pitch

envelope has no effect.

●

Decay Rate

≤ 0 … 127.

Sets the decay rate of the embouchure & pitch envelope. That is, the rate at which

the envelope level (pitch in the case of the pitch parameter) changes from the initial level

to “0” after the hold time has elapsed. The higher the value the faster the decay rate.

Time

Hold Time

Initial Lvl

Decay Rate

Level

-64

132

Feature Reference

●

Edit Mode

2-1: Embouchure & Pitch Hold Time Key Scaling

Embouchure & pitch hold time key scaling produces natural hold time variations

across the range of the keyboard by allowing different hold time offset values to be

applied to each of two breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly forward to the next

Embouchure & Pitch key scaling page without having to return to the main

parameter page.

●

HdTime

≤ 0 … 127.

The “HdTime” parameter is linked to the main Embouchure & Pitch “Hold

Time” parameter, and has the same effect. This value also determines the hold time on

which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of hold time offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the hold time, and positive

values increase the hold time at the corresponding breakpoint. No matter what offset

value is chosen, the actual hold time will never exceed its minimum or maximum abso-

lute value. When different offset values are applied to adjacent breakpoints, the hold time

varies smoothly between the breakpoints.

■ If two breakpoints are

set to the same note, the

lower one functions as the

end of the key scaling

segment connecting to the

next lowest breakpoint

while the higher one

functions as the end of the

segment connecting to the

next highest breakpoint.

Further, the higher

breakpoint applies to the

specified note while the

lower one actually applies

to the next note to its left.

If more than two break-

points are set to the same

note, only the lowest and

highest of these will

function as ends of the

corresponding key scaling

segments while the rest

are ignored.

BP3

BP2

BP4

BP1

BP5

C2 C3 C4

NOTES

133

Feature Reference

●

Edit Mode

2-2: Embouchure & Pitch Initial Level Key Scaling

Embouchure & pitch initial level key scaling produces natural initial level variations

across the range of the keyboard by allowing different level offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Embouchure & Pitch key scaling page

without having to return to the main parameter page.

●

IntLvl

≤ -64 … 63.

The “IntLvl” parameter is linked to the main Embouchure & Pitch “Initial

Level” parameter, and has the same effect. This value also determines the main initial

level on which all key-scaled variations are based (indicated by a dotted line on the

graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of initial level offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the initial level, and positive

values increase the initial level at the corresponding breakpoint. No matter what offset

value is chosen, the actual initial level will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the inital

level varies smoothly between the breakpoints.

Element Envelope

134

Feature Reference

●

Edit Mode

Embouchure & pitch decay rate key scaling produces natural decay rate variations

across the range of the keyboard by allowing different rate offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § button (“Bpag”) can be used to go directly backward to the next

Embouchure & Pitch key scaling page without having to return to the main

parameter page.

●

DcRate

≤ 0 … 127.

The “DcRate” parameter is linked to the main Embouchure & Pitch “Decay

Rate” parameter, and has the same effect. This value also determines the main decay

rate on which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of decay rate offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the decay rate, and positive

values increase the decay rate at the corresponding breakpoint. No matter what offset

value is chosen, the actual decay rate will never exceed its minimum or maximum abso-

lute value. When different offset values are applied to adjacent breakpoints, the decay

rate varies smoothly between the breakpoints.

2-3: Embouchure & Pitch Decay Rate Key Scaling

135

Feature Reference

●

Edit Mode

3: Vibrato

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the vibrato parameter page by pressing the ]

button.

• The • button (“Ctrl”) can be used to go directly to the vibrato controller

page (≥ Page 69), also available from the ELEMENT CONTROLLER

directory. You can then return to the vibrato parameter page by pressing •

(“Para”) again.

• The “Delay Time”, “Attack Rate”, and “Sustain Lvl” parameters

define the vibrato effect at all times, and do not affect vibrato as controlled via

a controller.

●

Delay Time

≤ 0 … 127.

Sets the delay time between the instant a note is played and the beginning of the

vibrato effect. The higher the value the longer the delay.

●

Attack Rate

≤ 0 … 127.

This parameter produces a gradual increase in vibrato depth when the vibrato effect

begins. The higher the value the faster the attack rate and therefore the faster the vibrato

“fade in”.

●

Sustain Lvl

≤ 0 … 127.

Sets the final vibrato depth after the delay time and attack have passed. The higher

the value the greater the vibrato depth. This parameter sets the vibrato depth independ-

ently of the depth applied by the controller assigned to vibrato. If you want to apply

vibrato via a controller only, set this parameter to “0”.

●

Vibrato Dpth

≤ 0 … 127.

Sets the vibrato depth as applied by the controller assigned to vibrato (≥ Page

69) and the vibrato envelope generator controlled by the “Delay Time”, “Attack

Rate”, and “Sustain Lvl” parameters. The higher the value the greater the vibrato

depth. When set to “0” no vibrato can be applied via a controller or the vibrato envelope

generator.

Element Envelope

136

Feature Reference

●

Edit Mode

●

Dpth to Emb

≤ 0 … 127.

Determines how deeply the settings in this display page affect embouchure. The

higher the value the greater the effect. When set to “0” no embouchure vibrato can be

applied.

●

Dpth to Ptch

≤ 0 … 127.

Determines how deeply the settings in this display page affect pitch. The higher the

value the greater the effect. When set to “0” no pitch vibrato can be applied.

●

Offset

≤ -127 … 127.

Sets the central value around which the vibrato variation occurs. For example, if the

“Dpth to Ptch” parameter is set to a high value and “Offset” is set to “0”, then

the vibrato will swing equally above and below the actual pitch of the note played.

Higher offset values shift the central vibrato pitch upward while lower values shift the

pitch downward.

●

Randomness

≤ 0 … 10.

The “Randomness” parameter can be used to introduce random variations in the

depth and speed of the vibrato effect. The higher the value the greater the random varia-

tion.

●

Speed

≤ 0 … 127.

Sets the speed of the vibrato effect. The higher the value the faster the vibrato.

●

Speed Shift

≤ 0 … 8.

Determines the amount of speed variation which can be applied via the controller

assigned to vibrato. The higher the value the greater the increase in speed. At the maxi-

mum setting of “8” the speed can be increased to a maximum of 6 times its normal

setting via the controller.

137

Feature Reference

●

Edit Mode

3-1: Vibrato Delay Time Key Scaling

Vibrato delay time key scaling produces natural delay time variations across the

range of the keyboard by allowing different delay time offset values to be applied to each

of two breakpoints set at appropriate keys.

• The ¶ button (“Fpag”) can be used to go directly forward to the next

Vibrato key scaling page without having to return to the main parameter page.

●

DlTime

≤ 0 … 127.

The “DlTime” parameter is linked to the main Vibrato “Delay Time” param-

eter, and has the same effect. This value also determines the main delay time on which all

key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of delay time offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the delay time, and positive

values increase the delay time at the corresponding breakpoint. No matter what offset

value is chosen, the actual delay time will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the delay

time varies smoothly between the breakpoints.

Element Envelope

138

Feature Reference

●

Edit Mode

3-2: Vibrato Attack Rate Key Scaling

Vibrato attack rate key scaling produces natural attack rate variations across the

range of the keyboard by allowing different rate offset values to be applied to each of two

breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Vibrato key scaling page without having to

return to the main parameter page.

●

AtRate

≤ 0 … 127.

The “AtRate” parameter is linked to the main Vibrato “Attack Rate” param-

eter, and has the same effect. This value also determines the main attack rate on which all

key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of attack rate offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the attack rate, and positive

values increase the attack rate at the corresponding breakpoint. No matter what offset

value is chosen, the actual attack rate will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

attack rate varies smoothly between the breakpoints.

139

Feature Reference

●

Edit Mode

3-3: Vibrato Depth Key Scaling

Vibrato depth key scaling produces natural vibrato depth variations across the range

of the keyboard by allowing different depth offset values to be applied to each of two

breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Vibrato key scaling page without having to

return to the main parameter page.

●

Depth

≤ 0 … 127.

The “Depth” parameter is linked to the main Vibrato “Vibrato Dpth” param-

eter, and has the same effect. This value also determines the main depth on which all

key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of depth offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the vibrato depth, and positive values

increase the vibrato depth at the corresponding breakpoint. No matter what offset value is

chosen, the actual depth will never exceed its minimum or maximum absolute value.

When different offset values are applied to adjacent breakpoints, the vibrato depth varies

smoothly between the breakpoints.

Element Envelope

140

Feature Reference

●

Edit Mode

3-4: Vibrato Speed Key Scaling

Vibrato speed key scaling produces natural vibrato speed variations across the range

of the keyboard by allowing different speed offset values to be applied to each of two

breakpoints set at appropriate keys.

• The § button (“Bpag” ) can be used to go directly backward to the next

Vibrato key scaling page without having to return to the main parameter page.

●

Speed

≤ 0 … 127.

The “Speed” parameter is linked to the main Vibrato “Speed” parameter, and has

the same effect. This value also determines the main speed setting on which all key-

scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of speed offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the vibrato speed, and positive values

increase the vibrato speed at the corresponding breakpoint. No matter what offset value is

chosen, the actual speed will never exceed its minimum or maximum absolute value.

When different offset values are applied to adjacent breakpoints, the vibrato speed varies

smoothly between the breakpoints.

141

Feature Reference

●

Edit Mode

4: Growl

• An inverse “K”(˚) next to a value means that key scaling can be applied to

that parameter. Position the cursor at the appropriate parameter and then press

the ¶ button (“KSC”) to go directly to the key scaling page for that param-

eter. You can return to the growl parameter page by pressing the ] button.

• The • button (“Ctrl”) can be used to go directly to the growl controller

page (≥ Page 74), also available from the ELEMENT CONTROLLER

directory. You can then return to the growl parameter page by pressing •

(“Para”) again.

●

Dpth to Pres

≤ 0 … 127.

Determines how deeply the settings in this display page affect pressure. The higher

the value the greater the effect. No growl effect will be produced if this and the “Dpth

to BNoise” parameter, below, are set to “0”.

●

Dpth to BNoise

≤ 0 … 127.

Determines how deeply the settings in this display page affect breath noise. The

higher the value the greater the effect.No growl effect will be produced if this and the

“Dpth to Pres” parameter, above, are set to “0”.

●

Offset

≤ -127 … 127.

Sets the central value around which the growl variation occurs. For example, if the

“Dpth to Pres” parameter is set to a high value and “Offset” is set to “0”, then

the growl variation will swing equally above and below the the actual pressure of the

note played. Higher offset values shift the central pressure value upward while lower

values shift the pressure downward. No growl effect will be produced when this param-

eter is set to “127”.

●

Vibrato Sync

≤ off, on.

Allows the growl variation to be synchronized to vibrato.

Element Envelope

Growl speed and randomness are synchronized to the same vibrato

parameters. In this case the speed and randomness parameters, listed

below, will not appear.

The growl variation is independent from the vibrato variation.

off

142

Feature Reference

●

Edit Mode

●

Speed

≤ 0 … 127.

Sets the speed of the growl effect. The higher the value the faster the growl.

●

Randomness

≤ 0 … 10.

The “Randomness” parameter can be used to introduce random variations in the

speed of the growl effect. The higher the value the greater the random variation.

4-1: Growl Speed Key Scaling

Growl speed key scaling produces natural growl speed variations across the range of

the keyboard by allowing different speed offset values to be applied to each of two

breakpoints set at appropriate keys.

●

Speed

≤ 0 … 127.

The “Speed” parameter is linked to the main Growl “Speed” parameter, and has

the same effect. This value also determines the main speed setting on which all key-

scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of speed offset for each of the breakpoints defined by the breakpoint

key parameters, above. Negative values reduce the growl speed, and positive values

increase the growl speed at the corresponding breakpoint. No matter what offset value is

chosen, the actual speed will never exceed its minimum or maximum absolute value.

When different offset values are applied to adjacent breakpoints, the growl speed varies

smoothly between the breakpoints.

143

Feature Reference

●

Edit Mode

5: Amplitude & Filter

• Two display pages are provided for Amplitude & Filter control. One contains

parameters pertaining to keyboard velocity sensitivity (“Sens”), while the

other contains the envelope generator parameters (“EG”). The ¡ and ™

buttons select these two display pages, respectively.

• An inverse “K”(˚) next to a value in the “EG” page means that key scaling

can be applied to that parameter. Position the cursor at the appropriate param-

eter and then press the ¶ button (“KSC”) to go directly to the key scaling

page for that parameter. You can return to the growl parameter page by

pressing the ] button.

Element Envelope

The parameters in the “Sens” page determine how the envelope settings in the

“Env” are affected by keyboard velocity.

●

Velocity Sens To Level

≤ 0 … 16.

Determines the relationship between the Amplitude & Filter envelope level and

keyboard velocity. When set to “0”, keyboard velocity (i.e. how fast or hard the keyboard

is played) has no effect on the envelope level. At values higher than “1”, however, high

keyboard velocities will increase the envelope level and low keyboard velocities will

decrease the envelope level. The higher the value the greater the effect of keyboard

velocity on the envelope level.

●

Velocity Sens To Rate

≤ 0 … 16.

Determines the relationship between the Amplitude & Filter envelope rates and

keyboard velocity. When set to “0”, keyboard velocity (i.e. how fast or hard the keyboard

is played) has no effect on the envelope rates. At values higher than “1”, however, high

The Sensitivity Parameters

144

Feature Reference

●

Edit Mode

keyboard velocities will increase the envelope rates and low keyboard velocities will

decrease the rates. The higher the value the greater the effect of keyboard velocity on the

envelope rates.

●

Depth To Amplitude

≤ 0 … 127.

Determines how deeply the Amplitude & Filter envelope will affect amplitude. The

higher the value the greater the effect.

●

Depth To Filter

≤ -127 … 127.

Determines how deeply the Amplitude & Filter envelope will affect the cutoff

frequency of the Dynamic Filter. The higher the value the greater the effect. Negative

values invert the effect of the envelope on the filter.

The parameters in this page set the actual “shape” of the envelope used for ampli-

tude and filter control. The parameters correspond to the envelope as shown in the

diagram below.

●

Rate: Attack1

≤ 0 … 127.

Determines the rate at which the envelope level goes from “0” to the level set by

the “Level: Attack1” parameter. The higher the value the faster the attack.

●

Rate: Attack2

≤ 0 … 127.

Determines the rate at which the envelope level goes from the level set by the

“Level: Attack1” parameter to maximum level. The higher the value the faster the

attack.

The Envelope Parameters

Time

Level

Key offKey on

Max.Level

(fixed:127)

Level:

Attack1

Level:

Sustain

Rate:

Attack2

Rate:

Attack1

Rate:

Decay

Rate:

Release

145

Feature Reference

●

Edit Mode

●

Rate: Decay

≤ 0 … 127.

Determines the rate at which the envelope level goes from maximum level to the

sustain level set by the “Level: Sustain” parameter. The higher the value the faster

the decay.

●

Rate: Release

≤ 0 … 127.

Determines the rate at which the envelope level goes from the sustain level to “0”

when the key is released. The higher the value the faster the release.

●

Level: Attack1

≤ 0 … 127.

Sets the envelope level reached by the first portion of the attack, as determined by

the “Rate: Attack1” parameter. The higher the value the higher the level. When set

to “127” the attack 1 level becomes the same as the maximum level, therefore the

second portion of the attack (“Rate: Attack2” parameter) will not be produced.

●

Level: Sustain

≤ 0 … 127.

Sets the envelope sustain level. The higher the value the higher the level. When set

to “127” the sustain level becomes the same as the maximum level, therefore the decay

Element Envelope

146

Feature Reference

●

Edit Mode

5-1: Amplitude & Filter Attack Rate Key Scaling

portion of the envelope (“Rate: Decay” parameter) will not be produced.

Amplitude & Filter attack rate key scaling produces natural attack rate variations

across the range of the keyboard by allowing different rate offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Amplitude & Filter key scaling page without

having to return to the main parameter page.

●

A1Rate, A2Rate

≤ 0 … 127.

The “A1Rate” and “A2Rate” parameters are linked to the main Amplitude &

Filter “Rate: Attack1” and “Rate: Attack2” parameters, and have the same

effect. These values also determine the main attack rates on which all key-scaled varia-

tions are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of attack rate offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the attack rate, and positive

values increase the attack rate at the corresponding breakpoint. No matter what offset

value is chosen, the actual attack rate will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

147

Feature Reference

●

Edit Mode

5-2: Amplitude & Filter Attack 1 Level Key Scaling

attack rate varies smoothly between the breakpoints.

Amplitude & Filter attack level key scaling produces natural attack level variations

across the range of the keyboard by allowing different level offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Amplitude & Filter key scaling page without

having to return to the main parameter page.

●

A1Lvl

≤ 0 … 127.

The “A1Lvl” parameter is linked to the main Amplitude & Filter “Level: At-

tack1” parameter, and has the same effect. This value also determines the main attack 1

level on which all key-scaled variations are based (indicated by a dotted line on the

graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of attack 1 level offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the attack 1 level, and positive

values increase the attack 1 level at the corresponding breakpoint. No matter what offset

value is chosen, the actual attack 1 level will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

Element Envelope

148

Feature Reference

●

Edit Mode

5-3: Amplitude & Filter Decay Rate Key Scaling

attack 1 level varies smoothly between the breakpoints.

Amplitude & Filter decay rate key scaling produces natural decay rate variations

across the range of the keyboard by allowing different rate offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Amplitude & Filter key scaling page without

having to return to the main parameter page.

●

DcRate

≤ 0 … 127.

The “DcRate” parameter is linked to the main Amplitude & Filter “Rate: De-

cay” parameter, and has the same effect. This value also determines the main decay rate

on which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of decay rate offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the decay rate, and positive

values increase the decay rate at the corresponding breakpoint. No matter what offset

value is chosen, the actual decay rate will never exceed its minimum or maximum abso-

lute value. When different offset values are applied to adjacent breakpoints, the decay

149

Feature Reference

●

Edit Mode

5-4: Amplitude & Filter Sustain Level Key Scaling

rate varies smoothly between the breakpoints.

Amplitude & Filter sustain level key scaling produces natural sustain level varia-

tions across the range of the keyboard by allowing different level offset values to be

applied to each of two breakpoints set at appropriate keys.

• The § and ¶ buttons (“Bpag” and “Fpag”) can be used to go directly

backward or forward to the next Amplitude & Filter key scaling page without

having to return to the main parameter page.

●

SusLvl

≤ 0 … 127.

The “SusLvl” parameter is linked to the main Amplitude & Filter “Level:

Sustain” parameter, and has the same effect. This value also determines the main

sustain level on which all key-scaled variations are based (indicated by a dotted line on

the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of sustain level offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the sustain level, and positive

values increase the sustain level at the corresponding breakpoint. No matter what offset

value is chosen, the actual sustain level will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

Element Envelope

150

Feature Reference

●

Edit Mode

5-5: Amplitude & Filter Release Rate Key Scaling

sustain level varies smoothly between the breakpoints.

Amplitude & Filter release rate key scaling produces natural release rate variations

across the range of the keyboard by allowing different rate offset values to be applied to

each of two breakpoints set at appropriate keys.

• The § button (“Bpag” and “Fpag”) can be used to go directly backward to

the next Amplitude & Filter key scaling page without having to return to the

main parameter page.

●

RlRate

≤ 0 … 127.

The “RlRate” parameter is linked to the main Amplitude & Filter “Rate: Re-

lease” parameter, and has the same effect. This value also determines the main release

rate on which all key-scaled variations are based (indicated by a dotted line on the graph).

●

Breakpoint 1 & 2 Key

≤ C-2 … G8.

Allows two separate key scaling breakpoints to be set at any notes between C-2 and

G8. You can position the cursor at the appropriate breakpoint key parameter and use any

of the normal data entry procedures, or use the keyboard. To use the keyboard for break-

point entry, position the cursor at the appropriate breakpoint key parameter, press the •

button (“Kbd”), and then press the key at which you want to set the breakpoint while

“Kbd” appears in inverse characters.

No breakpoint can be set to a key lower than the breakpoint to its left.

●

Breakpoint 1 & 2 Offset

≤ -64 … 63.

Set the amount of release rate offset for each of the breakpoints defined by the

breakpoint key parameters, above. Negative values reduce the release rate, and positive

values increase the release rate at the corresponding breakpoint. No matter what offset

value is chosen, the actual release rate will never exceed its minimum or maximum

absolute value. When different offset values are applied to adjacent breakpoints, the

release rate varies smoothly between the breakpoints.

Utility Mode

The UTILITY mode provides access to a range

of functions that do not necessarity affect the instru-

ment’s sound or how it plays. Select the UTILITY

mode from either the EDIT or PLAY mode by press-

ing the U button.

System . . . . . . . . . . . . . . . . . . . . . . . . . . 152

MIDI Bulk Dump . . . . . . . . . . . . . . . . . . 160

Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Edit Recall . . . . . . . . . . . . . . . . . . . . . . . 172

Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . 174

152

Feature Reference

●

Utility Mode

System

UTILITY MODE

DEMO

EDIT RECALL

MIDI BULK DUMP

SYSTEM

DISK

■ 1: KBD Setting . . . . . . . . . . . . . . . . . . . . . . . . . 153

■ 2: TG Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 154

■ 3: MIDI Setting . . . . . . . . . . . . . . . . . . . . . . . . . 155

■ 4: Assignable Controllers . . . . . . . . . . . . . . . . 156

■ 5: Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

■ 6: Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . 158

153

Feature Reference

●

Utility Mode

System

1: KBD Setting

●

Keyboard Transpose

≤ -12 … 12.

Shifts the overall pitch of the VL1 up or down in semitone steps. A setting of “-

12”, for example, shifts the pitch down by one octave; a setting of “+4” shifts the pitch

up by a major third.

• This setting also affects MIDI note numbers transmitted via the MIDI OUT

connector.

●

Octave SW Hold

≤ off, on.

Normally (when this parameter is “off”) the OCTAVE buttons to the left of the

keyboard only shift the pitch of the keyboard as long as they are held. When this param-

eter is turned “on”, however, you press an OCTAVE button once to shift the pitch and

then again to return.

154

Feature Reference

●

Utility Mode

2: TG Setting

●

Master Tuning

≤ -64 … 63.

Fine tunes the overall pitch of the VL1 in approximately 1.17-cent steps (a “cent” is

1/100th of a semitone). The maximum minus setting of “-64” produces a downward

pitch shift of almost three-quarters of a semitone, and the maximum plus setting of “63”

produces an upward pitch shift of the same amount. A setting of “0” produces no pitch

change.

●

Reverb

≤ off, on.

Turns the VL1’s internal reverb system off or on. This can be handy if you want to

use an external signal processor for rverberation.

●

Output

≤ Monaural, Stereo.

Determines whether the VL1 output is delivered in mono or stereo. When the

“Monaural” setting is selected the same signal is output via the both the L and R OUT-

PUT jacks. Also, in the mono mode all parameters relating to panning or positioning in

the stereo sound field have no effect.

155

Feature Reference

●

Utility Mode

3: MIDI Setting

●

Transmit Channel

≤ 1 … 16.

Selects the MIDI channel via which all VL1 data will be transmitted.

●

Receive Channel

≤ 1 … 16, Omni.

Sets the MIDI receive channel to any channel between 1 and 16, or the “Omni”

mode for reception on all channels. Make sure that the VL1 MIDI receive channel is

either set to the channel that your external controller is transmitting on, or the omni

mode.

●

Local on/off

≤ off, on.

“Local control” refers to the fact that, normally, the VL1 keyboard controls its

internal tone generator, allowing the internal voices to be played directly from the key-

board. This situation is “local control on” since the internal tone generator is controlled

locally by its own keyboard. Local control can be turned off, however, so that the key-

board does not play the internal voices, but the appropriate MIDI information is still

transmitted via the MIDI OUT connector when notes are played on the keyboard. At the

same time, the internal tone generator responds to MIDI information received via the

MIDI IN connector.

●

Device Number

≤ off, 1 … 16, All.

Sets the MIDI device number — i.e. the MIDI channel on which all system exclu-

sive data (included in MIDI bulk dump data) will be received and transmitted. When

“All” is selected reception occurs on all channels and transmission occurs via Device

Number 1.

The device number is important for transfer of voice data and other system exclu-

sive data between the VL1 and other MIDI devices — e.g. another VL1, a computer, or a

MIDI data recorder. Make sure that the VL1 device number is matched to that of other

devices in your system with which such data transfers will take place.

System

156

Feature Reference

●

Utility Mode

4: Assignable Controllers

●

Modulation Wheel 2

≤ off, Modulation Wheel … 119.

Sets the MIDI control number for Modulation Wheel 2. All MIDI control numbers

are available. Modulation Wheel 2 will not function when this parameter is turned “off”.

• Modulation Wheel 1 is fixed at MIDI control number 001.

●

Foot Controller 2

≤ off, Modulation Wheel … 119.

Sets the MIDI control number for Foot Controller 2. All MIDI control numbers are

available. Foot Controller 2 will not function when this parameter is turned “off”.

• Foot Controller 1 is fixed and MIDI control number 004.

●

Foot Switch 1 & 2

≤ off, Modulation Wheel … 119, Program Inc.

Sets the MIDI control number for Foot Switches 1 & 2. All MIDI control numbers

are available. When “Program Inc” is selected the VL1 voice number will increase by 1

each time the foot switch is pressed (the corresponding MIDI program change numbers

are also transmitted). When voice number “128” is reached, the next voice selected will

be “1”. Foot Switch 1 or 2 will not function when this parameter is turned “off”.

• The initial factory settings for the assignable controllers are as follows:

• Modulation Wheel 2...... Breath Controller

• Foot Controller 2 ........ Breath Controller

• Foot Switch 1 ........... Sustain

• Foot Switch 2 ........... Portamento Switch

157

Feature Reference

●

Utility Mode

5: Curve

Three curve display pages are provided: one for the velocity curve (“Velo”), one for the

aftertouch curve (“Aftr”), and one for the breath controller curve (“Brth”). Press the §,

¶, and • buttons to select these pages, respectively.

●

Velocity Curve

≤ Normal, Soft, Wide, Hard.

●

After Touch Curve

≤ Normal, Soft, Wide, Hard.

●

Breath Control Curve

≤ Normal, Soft, Wide, Hard.

Determine the relationship between controller input — keyboard velocity, keyboard

aftertouch, and breath controller — and output. For example, a player who generally uses

a light keyboard touch will get maximum dynamic range from the VL1 keyboard if the

“Velocity Curve” parameter is set to “Soft”. Try out the various settings while

playing the respective controllers in order to find the curves that work best for you.

System

• If you play the keyboard or breath controller while viewing the appropriate

curve display, the instantaneous velocity, aftertouch, or breath pressure input

and output values will appear on the display both numerically and graphically

in the form of markers surrounding the curve graph.

The relationship between input and output is linear.

This curve makes it easy to cover a wide dynamic range with a light

keyboard touch.

Subjectively, this curve produces the widest dynamic range.

Best for players who use a relatively heavy touch.

Normal

Soft

Wide

Hard

158

Feature Reference

●

Utility Mode

6: Miscellaneous

●

Display

≤ Reverse, Normal.

Determines whether the VL1 display appears in the normal way (black characters

on a white background) or reverse (white characters on a black background).

●

Confirm

≤ off, on.

Determines whether the “Are you sure” confirmation message will appear during

the following operations:

• Voice store.

• Disk save, load, rename, delete, format.

• Bulk data transmit.

• Edit recall.

• Demo data load.

• Turning the confirmation function off can make operation faster and more

efficient by reducing the number of steps required for some operations, but it

also increases the danger of accidentally erasing important data. Use with

caution.

●

Memory Protect

≤ off, on.

Turns internal RAM memory protection on or off. When “on” no operations that

alter the contents of the internal memory can be performed. Be sure to turn memory

protection “off” before loading data, storing voices, receiving bulk data from external

equipment, etc.

• Memory protection is automatically turned “on” when the demo data is

loaded.

●

Greeting Message

≤ Up to 20 characters.

Allows you to enter an original greeting message which will be displayed by the

VL1 when the power is initially turned on. Position the cursor at the “Greeting Message”

159

Feature Reference

●

Utility Mode

parameter and press the • button (“Name”). Then use the name entry procedure de-

scribed on page 31.

System

160

Feature Reference

●

Utility Mode

MIDI Bulk Dump

UTILITY MODE

DEMO

EDIT RECALL

MIDI BULK DUMP

SYSTEM

DISK

161

Feature Reference

●

Utility Mode

MIDI Bulk Dump

MIDI “bulk dump” transmission makes it possible to transfer system and voice data

between the VL1 and other MIDI equipment. The VL1 is capable transmitting three types

of data:

●

Bulk Data Transmission Procedure

1. Preparation

Make sure the VL1 is properly connected to a device which is capable of receiving

its bulk data: another VL1, a computer, a MIDI data recorder, etc. The VL1 MIDI OUT

connector should be connected to the MIDI IN connector of the receiving device via a

high-quality MIDI cable. Also make sure that the VL1 and receiving device are set to the

same MIDI Device Number.

2. Select a Data Type

Position the cursor at the type of bulk data you want to send — “System”, “All

Voice”, or “Current Voice”.

3. Press [

Press the [ button. The “Are You Sure?” confirmation display will

appear.

4. Press - to Transmit

Press the - button to transmit the selected data (or = to cancel the opera-

tion). The progress of the transmission will be indicated in bar-graph form on the display,

and “Completed” will appear when all the data has been transmitted.

•“System” and “All Voice” transmissions can be cancelled between

blocks by pressing the ] button.

5. Press ]

Press the ] button to clear the “Completed” display and return to the main

bulk transmit display.

All VL1 system Data: the settings in the Utility System page and the 2

internal Micro Tuning data.

All 128 voices in the VL1 memory.

The currently selected voice only.

1: System

2: All Voice

3: Current Voice

●

Bulk Data Reception

In order for the VL1 to receive a bulk transmission from another VL1 or other

device, the MIDI OUT of the transmitting device must be connected to the MIDI IN of

the VL1 via a MIDI cable. The VL1 will then automatically receive and load the data as

long as it is set to the same device number as the transmitting device and its Memory

Protect function is turned “off”. Memory Protect does not need to be turned off in order

to receive a single voice (the current voice).

162

Feature Reference

●

Utility Mode

Disk

UTILITY MODE

DEMO

EDIT RECALL

MIDI BULK DUMP

SYSTEM

DISK

■ 1: Disk Status . . . . . . . . . . . . . . . . . . . . . . . . . . 163

■ 2: Load From Disk . . . . . . . . . . . . . . . . . . . . . . 164

■ 3: Save To Disk . . . . . . . . . . . . . . . . . . . . . . . . 166

■ 4: Rename File . . . . . . . . . . . . . . . . . . . . . . . . . 168

■ 5: Delete File . . . . . . . . . . . . . . . . . . . . . . . . . . 170

■ 6: Format Disk . . . . . . . . . . . . . . . . . . . . . . . . . 171

CAUTION! ■ Never attempt to remove a disk from the disk drive while the disk

drive indicator is lit. Doing so can damage the data on the disk.

■ The disk write protect tab must be set to the “off” or “write enable” position

in order to save data to the disk, rename a file, delete a file, or format the disk.

CAUTION!

163

Feature Reference

●

Utility Mode

1: Disk Status

This function displays a range of information about the currently loaded floppy

disk.

Disk

The total number of files on the disk.

The amount of disk space currently used, in kilobytes.

The amount of disk space currently free, in kilobytes.

The number of “System” files on the disk.

The number of “All Voice” files on the disk.

The number of “1 Bank” files on the disk.

The number of “1 Voice” files on the disk.

The number of files on the disk that do not match any of the above

categories.

Total

Used

Free

System

All Voice

1 Bank

1 Voice

Others

164

Feature Reference

●

Utility Mode

2: Load From Disk

This function loads a specified data file from a floppy disk inserted in the VL1

floppy disk drive. Five types of data files can be selected.

All system and voice data.

All Utility System page settings and internal Microtuning data.

All 128 voices in the the VL1 memory.

16 voices from 1 VL1 memory bank (A … H).

1 voice.

All

System

All Voice

1 Bank

1 Voice

●

Disk Load Procedure

1. Insert the Floppy Disk

Make sure the floppy disk containing the data you want to load is properly inserted

in the VL1 floppy disk drive.

• Also make sure that the VL1 Memory Protect function is turned “off” (≥

Page 158).

2. Select a File Type and press [

Position the cursor at the type of file you want to load, then press the [

button.

3. Select a File and Press [

When the file window appears, select the file you want to load and press [

again.

Depending on the type of data you have selected, an additional selection window

may appear after you have selected the file you want to load. You may have to select an

individual bank or voice, or specify a destination for the data to be loaded (“SRC” in the

selection window title indicates that you are selecting a source file, while “DST” indicates

that you are selecteing a destination). Continue making the required selections and

presing [ until the confirmation prompt appears.

• When selecting a voice to load from a long list, you can use the § (“123”)

and ¶ (“ABC”) buttons to display the voices in numeric or alphabetic order,

as required. Sometimes it may take a few seconds to sort the data as specified

— the “Now Sorting!” message will appear during the sort operation.

165

Feature Reference

●

Utility Mode

4. Press - to Load

When the “Are You Sure” confirmation prompt appears, press the - button

to load the selected data (or = to cancel the operation). The progress of the load

operation will be indicated in bar-graph form on the display, and “Completed” will

appear when all the data has been loaded.

• A load operation in progress cannot be cancelled.

5. Press ]

Press the ] button to clear the “Completed” display.

CAUTION! ■ Whenever a load operation is performed any previous data in the

memory location to which the new data is loaded to will be erased and replaced

by the new data! Be sure to save important data to disk to minimize the possibil-

ity of accidental erasure.

Disk

CAUTION!

166

Feature Reference

●

Utility Mode

3: Save To Disk

This function saves a specified data file from the VL1 memory to a floppy disk

inserted in the VL1 floppy disk drive. Five types of data files can be selected.

●

Disk Save Procedure

1. Insert the Floppy Disk

Make sure the floppy disk to which you want to save the data is properly inserted in

the VL1 floppy disk drive.

• Also make sure that the floppy disk’s write protect tab is set to the “off” or

“write enable” position.

• Only floppy disks which have been formatted using the “Format Disk” func-

tion (≥ Page 158) can be used to save VL1 data.

2. Select a File Type and press [

Position the cursor at the type of file you want to save, then press the [

button.

If you select “All”, “System” or “All Voice” a list of the files on disk will

appear. In this case skip step 3, below, and go directly to step 4. If you select “1 Bank”

or “1 Voice” continue with step 3.

3. Select a Bank or Voice and Press [

When the source window appears, select the bank or voice you want to save and

press [.

4. Select the Destination File

If you want to save the selected data to a new file, position the cursor at a file name

with the “NewFile” extension. To save the data to an existing file, position the cursor at

the appropriate file name. In the latter case there is no need to enter a new file name, sou

you can skip ahead top step 7.

All system and voice data.

All Utility System page settings and internal Microtuning data.

All 128 voices in the the VL1 memory.

16 voices from 1 VL1 memory bank (A … H).

1 voice.

All

System

All Voice

1 Bank

1 Voice

167

Feature Reference

●

Utility Mode

5. Enter a File Name

Press ∞ (“Name”) and enter a name (maximum 8 characters) for the file to be

saved (≥ Page 31).

• File names which begin with or contain a space are not allowed.

6. Press ] or [

Press the ] or [ button to close the name window.

7. Press [ and Confirm

Press the [ button. When the “Are You Sure?” confirmation prompt

appears, press the - button to save the selected data (or = to cancel the opera-

tion). The progress of the save operation will be indicated in bar-graph form on the

display, and “Completed” will appear when all the data has been saved.

• A save operation in progress cannot be cancelled.

• Files are automatically saved with an extension (a period followed by three

characters) which indicates the file type: .ALL = All Data; .SYS = System;

.AVC = All Voice; .1BK = 1 Bank; .1VC = 1 Voice.

8. Press ]

Press the ] button to clear the “Completed” display.

Disk

168

Feature Reference

●

Utility Mode

4: Rename File

This function can be used to rename a specified data file on a floppy disk inserted

in the VL1 floppy disk drive. Five types of data files can be selected.

All system and voice data.

All Utility System page settings and internal Microtuning data.

All 128 voices in the the VL1 memory.

16 voices from 1 VL1 memory bank (A … H).

1 voice.

All

System

All Voice

1 Bank

1 Voice

●

File Rename Procedure

1. Insert the Floppy Disk

Make sure the floppy disk containing the file you want ot rename is properly

inserted in the VL1 floppy disk drive.

• Also make sure that the floppy disk’s write protect tab is set to the “off” or

“write enable” position.

2. Select a File Type and press [

Position the cursor at the type of file you want to rename, then press the [

button.

3. Select a File and Press ∞

When the file window appears, select the file you want to rename and press the ∞

button (“Rnam”).

4. Enter a File Name

Enter a new name (maximum 8 characters) for the selected file (≥ Page 31).

• File names which begin with or contain a space are not allowed.

5. Press ] or [

Press the ] or [ button to close the name window.

169

Feature Reference

●

Utility Mode

6. Press [ and Confirm

Press the [ button. When the “Are You Sure?” confirmation prompt

appears, press the - button to rename the file (or = to cancel the operation). “Now

Executing” will appear while the file name is being rewritten, and “Completed”

will appear when the rename operation is finished.

7. Press ]

Press the ] button to clear the “Completed” display.

Disk

170

Feature Reference

●

Utility Mode

5: Delete File

This function can be used to delete a specified data file on a floppy disk inserted in

the VL1 floppy disk drive. Six types of data files can be selected.

●

File Delete Procedure

1. Insert the Floppy Disk

Make sure the floppy disk containing the file you want ot delete is properly inserted

in the VL1 floppy disk drive.

• Also make sure that the floppy disk’s write protect tab is set to the “off” or

“write enable” position.

2. Select a File Type and press [

Position the cursor at the type of file you want to delete, then press the [

button.

3. Select a File and Press [

When the file window appears, select the file you want to delete and press [.

4. Press - To Delete

When the “Are You Sure?” confirmation prompt appears, press the -

button to delete the file (or = to cancel the operation). “Now Executing” will

appear while the file is being deleted, and “Completed” will appear when the delete

operation is finished.

5. Press ]

Press the ] button to clear the “Completed” display.

All system and voice data.

All Utility System page settings and internal Microtuning data.

All 128 voices in the the VL1 memory.

16 voices from 1 VL1 memory bank (A … H).

1 voice.

Any files not included in the above categories.

All

System

All Voice

1 Bank

1 Voice

Others

171

Feature Reference

●

Utility Mode

6: Format Disk

This function formats new 2DD or 2HD type floppy disks for use with the VL1.

• 2DD type disks provide 720 kilobytes of storage capacity when formatted

(MS-DOS 9-sector format), and 2HD disks have 1.44 megabytes of storage

capacity when formatted (MS-DOS 18-sector format).

●

Disk Format Procedure

1. Insert the Floppy Disk

Make sure the floppy disk you want to format is properly inserted in the VL1

floppy disk drive.

• Also make sure that the floppy disk’s write protect tab is set to the “off” or

“write enable” position.

2. Press [ and Confirm

Press the [ button. When the “Are You Sure?” confirmation prompt

appears, press the - button to begin formatting the disk (or = to cancel the

operation). The progress of the format operation will be indicated on the display in bar

graph form, and “Completed” will appear when the format operation is finished.

3. Press ]

Press the ] button to clear the “Completed” display.

CAUTION! ■ Formatting a disk that contains data will erase all data on the

disk!

Disk

CAUTION!

172

Feature Reference

●

Utility Mode

Edit Recall

UTILITY MODE

DEMO

EDIT RECALL

MIDI BULK DUMP

SYSTEM

DISK

173

Feature Reference

●

Utility Mode

Edit Recall

If you’ve accidentally “lost” an edited voice by selecting a different voice in the

PLAY mode before storing your edited data, the Edit Recall function can be used to

recall the edited data.

• If you’ve made no further edits to any other voice since losing the data, only

the name of the last voice edited (the “Recall Memory Voice”) will

appear on the display. If you’ve already made at least one edit to the newly

selected voice both the name of the recall memory voice and the current voice

will appear on the display — with the warning that the current voice will be

overwritten by the recall memory voice if you proceed with the recall opera-

tion!

●

Edit Recall Procedure

1. Press [ and Confirm

Press the [ button. When the “Are You Sure?” confirmation prompt

appears, press the - button to recall the edit data (or = to cancel the operation).

“Completed” will appear when the recall operation is finished.

2. Press P

Press the P button to return to the PLAY mode. “E”(´) will appear to the left

of the voice name.

174

Feature Reference

●

Utility Mode

Demo

UTILITY MODE

DEMO

EDIT RECALL

MIDI BULK DUMP

SYSTEM

DISK

175

Feature Reference

●

Utility Mode

Demo

The VL1 includes a built-in demonstration which can be played as follows.

●

Demo Playback Procedure

1. Check Your Bank-H Voices!

When the VL1 demo is played, the voices used are automatically loaded into bank

H, erasing any other data which may be in those memory locations. Please note that all

system data, excluding the Assignable Controller settings, are also affected. Make sure

bank H does not contain any important or irreplacable data before running the demo.

2. Press [

Press the [ button. The demo selection, start, and stop control display should

appear.

3. Select a Demo

Select the demo you want to play (“Top Song” parameter).

4. Press • To Run

Press the • button to run the demo. The various demo songs will play in sequence

until stopped.

5. Press ¶ To Stop

Press the ¶ button to stop demo playback.

2nd Layout (11.22)

VL1

Feature Reference

(p84-150)

Appendix

Troubleshooting . . . . . . . . . . . . . . . . . . . 178

Error Messages . . . . . . . . . . . . . . . . . . . 180

Specifications . . . . . . . . . . . . . . . . . . . . 184

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

178

Feature Reference

●

Appendix

Troubleshooting

The VL1 is a very versatile instrument with many features and functions that affect

operation. In many cases, what appears to be a fault with the VL1 can actually be traced

to an improperly set parameter or, at the most fundamental level, to something as simple

as a bad connection.

Here’s how to determine if the problem is internal (e.g. parameter settings) or

external (e.g. connections, amplifier, etc.):

● Listen Via Headphones. Plug a pair of headphones into the VL1 and play.

If the headphone sound is OK, then the problem is most likely in the

amplifier or mixer you are using, or the audio connection cables.

● Try moving all controllers — modulation wheels, foot controlers, etc. In

some cases extreme controller settings can cause unexpected sound ir

pitch … or even no sound at all.

● Try selecting diferent voices. If the problem occurs only on one voice then

the voice parameters are most likely at fault. If the problem occurs on all

voices then a utility parameter should be suspected.

The following are some common problems and probable causes:

179

Feature Reference

●

Appendix

Troubleshooting

●

Amplifier, Mixer, Connection Problems

Symptom

Possible Cause

• Is the amplifier/mixer power turned on?

• Is the amplifier/mixer volume set to an appropriate level?

• Are the VL1 outputs properly connected to the amplifier/mixer

inputs?

• Are the connection cables shorted, open, or otherwise faulty?

• Is the VL1 connected to a high-sensitivity microphone or instru-

ment input on your amplifier or mixer? Try turning the VL1

DOWN controls down to avoid overloading the amplifier/mixer

inputs.

• Check the level and pan controls on the sound system/mixing

console being used with the VL1.

No sound.

Distorted sound.

Improper stereo positioning.

●

Utility Setting Problems

Symptom

Possible Cause

• Is the local off mode selected (page 155).

• Are the MIDI transmit channel and receive channels matched to

those of the external MIDI device used (page 155)?

• Is the master tune parameter set properly (page 154)?.

• Is the keyboard transpose parameter set properly (page 153)?.

• Is the TG Setting Reverb parameter turned “on” (page 154)?.

• Are the Assignable Controllers parameters set properly (page

156)?.

• When the VL1 is initially shipped, or when the “FACTORY” data

file on the supplied disk is loaded, both Modulation Wheel 2 and

Foot Controller 2 are assigned to breath control.

• When the “CUSTOMER” data file on the supplied disk is loaded

Modulation Wheel 2 is assigned to MIDI control change number

013. In tbis case “normal” sound is produced with the modulation

wheel at its center position.

No Sound

Wrong pitch.

No reverb.

Improper controller operation.

180

Feature Reference

●

Appendix

●

Voice Setting Problems

Symptom

Possible Cause

• Is the appropriate element selected (page 26)?.

• Make sure that the element level is not set to “0” (page 38)?.

• Make sure that the total amplitude level is not set to “0” (page

104)?.

• Make sure that the driver, pipe/strings, and tap output mixing

parameters are not all set to “0” (page 98)?.

• Make sure that the amplitude & filter sustain level is not set to

“0” (page 145).

• Check the pressure controller (page 65)?.

• Check the amplitude controller (page 71)?.

• Check the embouchure controller (page 66)?.

• Check the damping controller (page 80)?.

• Check the absorption controller (page 81)?.

• Some voices will not produce sound when played at extremely

high or low pitches.

• Make sure that the pressure EG mode parameters is not set to

“Disable” (page 129)?.

• Check the element detune, note shift, and random pitch param-

eters (page 37)?.

• Microtuning may be set to a tuning other than equal tempera-

ment (page 42)?.

• Check the effect pitch change parameters (page 50)?.

• Check the pitch controller (page 67)?.

• Some voices will change pitch when pressure or embouchure

control is applied.

• Check the effect distortion settings (page 51)?.

• Check the scream controller (page 72)?.

• Check the growl controller (page 74)?.

• Check the throat formant controller (page 75)?.

• Are the element pan L and R parameters set to values other

than “-64” and “63”, respectively (page 38)?.

• Check the effect feedback delay settings (page 53)?.

• Make sure that the key mode and voice mode parameters are

set properly (page 31,32)?.

• Check the controller assigned to polyphony control.

No sound.

Sound won’t stop.

Wrong pitch.

Distorted sound.

Improper stereo positioning.

Can’t play two notes

simultaneously.

181

Feature Reference

●

Appendix

Troubleshooting

182

Feature Reference

●

Appendix

Error Messages

When an operational error or other problem occurs, the VL1 will display one of the

following error messages to inform you of the problem.

Display

Comments

The loaded floppy disk is damaged. Try a different disk.

The voice backup battery needs to be replaced. Have the battery

replaced by qualified Yamaha service personnel.

The specified data cannot be found on the currently loaded

floppy disk, or different data is loaded. Make sure the appropriate

disk is loaded.

MIDI bulk data could not be transmitted or received because the

device number parameter is turned off. Check the device number

setting.

MIDI bulk data could not be transmitted or received because the

device number of the VL1 is not matched to that of the second

device. Check the device number settings.

Data cannot be saved to floppy disk because the currently

loaded disk is full. Delete unwanted files to make more space on

the disk, or use a different disk.

The currently loaded floppy disk has not been formated for use

with the VL1. Format the disk before performing any disk opera-

tions.

You have attempted to perform a disk operation while no floppy

disk is loaded. Insert an appropriate floppy disk in the disk drive.

The specified file cannot be found on the currently loaded floppy

disk. Check the file name or use the appropriate disk.

Bad disk!

Change battery!

Data not found!

Device number is off!

Device number mismatch!

Disk full!

Disk not formatted!

Disk not ready!

File not found!

183

Feature Reference

●

Appendix

Error Messages

Display

Comments

Illegal disk!

Illegal file!

Memory protected!

MIDI buffer full!

MIDI checksum error!

MIDI data error!

Same file name exists!

Write protected!

The currently loaded disk has a non-VL1 format. Either use a

different disk or, if the data on the disk is not needed, re-format the

disk.

The specified file is not a VL1 file. Check the disk and files.

You have attempted to perform a function which will change the

contents of the internal memory, but the memory protect function is

“on”. Turn memory protect “off” and try again.

The MIDI receive buffer is full. Reduce the amount of data being

transmitted to the VL1.

An error has been detected in the received MIDI data. Check the

transmitting device and MIDI cables, and try again.

An error has been detected in the received MIDI data. Check the

transmitting device and MIDI cables, and try again.

You have attempted to save a file with the same name as a file

that already exists on the disk. Change the file name and try again.

You have attepted a save, rename, or delete operation to a disk

which is write protected. Set the disk’s write protect tab to the “off”

or “enable” position and try again.

184

Feature Reference

●

Appendix

Specifications

●

Tone Generator

S/VA (Self-oscillating Virtual Acoustic Synthesis.

Harmonic Enhancer.

Dynamic Filter (LPF, HPF, BPF, BEF, with resonance).

Equalizer (5 bands with frequency, resonace, and boost/cut

control).

Impulse Expander.

Resonator.

32-bit digital signal processor, stereo in/stereo out.

Modulation effects (flanger, pitch change, distorion).

Feed back delay.

Reverberation.

Voice mode only.

Smallest tone generator units: elements. Voices use 1 or 2

elements.

Voices are composed on “common data” and “element data”.

2 notes max.

Mono, Poly, Unison

Type

Modifiers

Effects

Play Mode

Polyphony

Assign Modes

●

Memory

128 voices.

3.5" 2DD or 2HD floppy disk.

Internal

Disk

●

Keyboard

49 (C scale, FS type)

Velocity.

Channel aftertouch.

Keys

Sensitivity

●

Controllers

Master volume slider. Continuous sliders x 2.

Pitch bend wheel. Modulation wheel x 2.

Data entry dial. LCD contrast control.

185

Feature Reference

●

Appendix

Specifications

●

Panel Switches

Play (with LED). Edit (with LED).

Utility (with LED). Octave x 2 (with LEDs).

Copy. Store.

Bank select x 8 (with LEDs). Program change x 16 (with LEDs).

Data entry x 2. Cursor x 4.

Function x 8.

Exit. Enter.

●

Display

240 x 64 dot backlit liquid crystal display.

●

Connectors

Stereo headphones. Breath controller.

Output x 2 (L and R). Foot controller x 2.

Foot switch x 2. MIDI IN.

MIDI OUT. MIDI THRU.

Front Panel

Rear Panel

●

Output Level

2.5 ±2 dBm into 10 kΩ.

7.5 ±2 dBm into 150 Ω.

Line

Headphones

●

Power Requirements

UL/CSA: 120V, 16W

Europe: 220-240V, 16W

●

General

914 (W) x 380 (D) x 105 (H) mm.

12.5 kg

Dimensions

Weight

●

Accessories

Power cable. BC2 Breath Controller.

FC7 Foot Controller. Floppy disk.

Owners manuals x 2.

186

Feature Reference

●

Appendix

Copy button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Copy function . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ25

Crossfade speed . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ85

Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ80

Data dial . . . . . . . . . . . . . . . . . . . . . .

Decrement & increment buttons . . .

Demo playback . . . . . . . . . . . . . . . . . . .

Device number . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ155

Disk format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ171

Disk status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ163

Disk, delete file . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ170

Disk, load from . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ164

Disk, rename file . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ168

Disk, save to . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ166

Display mode . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ158

Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ51

Dynamic filter . . . . . . . . . . . . . . . . .

Dynamic filter key scaling . . . . . . . . . . . . .

ƒ117-118

Edit compare function . . . . . . . . . . . . . . . . . . . . . ƒ24

Edit recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ173

Effect control . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ45

Effect on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ23

Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Element detune . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ37

Element level . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ38

Element names . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ31

Element note shift . . . . . . . . . . . . . . . . . . . . . . . . . ƒ37

Index

This index covers both the VL1 Getting Started and Feature Reference manuals for

easy cross-referencing. Page numbers in the Getting Started manual are preceded by

“

Absorption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ81

Aftertouch curve . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ157

Amplitude & filter envelope . . . . . . . . . . . . . . .

ƒ143

Amplitude & filter key scaling . . . . . . . . .

ƒ146-150

Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ71

Assign mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ35

Bank buttons . . . . . . . . . . . . . . . . . . .

Breath attack gain . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ36

Breath attack time . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ36

Breath control curve . . . . . . . . . . . . . . . . . . . . . .

ƒ157

Breath controller calibration . . . . . . . . . . . . . . . . .

Breath controller jack . . . . . . . . . . . . . . . . . . . . . .

Breath noise . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ73, 86

Breath noise key scaling . . . . . . . . . . . . . . . . .

ƒ88-90

Bulk dump, MIDI . . . . . . . . . . . . . . . . . . . . . . . .

ƒ161

Common miscellaneous . . . . . . . . . . . . . . . . . . . . ƒ34

Confirm mode . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ158

Continuous slider assignment . . . . . . . . . . . . . . . .

ƒ43

Continuous sliders . . . . . . . . . . . . . . .

Controller envelopes . . . . . . . . . . . . . . . . . . . . . . .

Controller search & replace . . . . . . . . . . . . . . . . .

ƒ82

Controller parameters . . . . . . . . . . . . . . . . . . . . . .

Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . .

187

Feature Reference

●

Appendix

Index

Element on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ22

Element pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ38

Element random pitch . . . . . . . . . . . . . . . . . . . . . .

ƒ37

Element select . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ22

Embouchure & pitch envelope . . . . . . . . . . . . . .

ƒ130

Embouchure & pitch envelope key scaling

ƒ132-134

Embouchure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ66

Enter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equalizer auxiliary . . . . . . . . . . . . . . . . . . . . . . .

ƒ119

Equalizer band . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ122

Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equalizer key scaling . . . . . . . . . . . . . . . . .

ƒ120-121

Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ180

Exit button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Feedback delay . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ53

Feedback delay/reverb mode . . . . . . . . . . . . . . . .

ƒ45

Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ47

Floppy disks & drive, handling . . . . . . . . . . . . . . .

Foot controller 2 assign . . . . . . . . . . . . . . . . . . .

ƒ156

Foot controller jacks . . . . . . . . . . . . . . . . . . . . . . .

Foot controllers . . . . . . . . . . . . . . . . . . . . . . . . . . .

Foot switches . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Foot switch assign . . . . . . . . . . . . . . . . . . . . . . . ƒ156

Foot switch jacks . . . . . . . . . . . . . . . . . . . . . . . . .

Function buttons . . . . . . . . . . . . . . . . . . . . . . . . . .

Functions & parameters, finding . . . . . . . . . . . . . .

ƒ9

Greeting message . . . . . . . . . . . . . . . . . . . . . . . . ƒ158

Growl envelope . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ141

Growl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ74

Growl speed key scaling . . . . . . . . . . . . . . . . . .

ƒ142

Harmonic enhancer key scaling . . . . . . . . .

ƒ110-115

Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Impulse expander & resonator setting . . . . . . . . ƒ123

Impulse expander . . . . . . . . . . . . . . . . .

Initial edit page . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ30

Interpolate speed . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ85

Key mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ31

Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keyboard transpose . . . . . . . . . . . . . . . . . . . . . . .

ƒ153

L,C,R delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ57

L,R delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ55

Local on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ155

Master tuning . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ154

Memory protect . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ158

Micro tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ42

MIDI connectors . . . . . . . . . . . . . . . . . . . . . . . . . .

MIDI settings . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ155

Mixing . . . . . . . . . . . . . . . . . . . . . . . . . . .

Mixing key scaling . . . . . . . . . . . . . . . . . . .

ƒ100-105

Mode buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Modes, the 3 main . . . . . . . . . . . . . . . . . . . . . . . . . ƒ8

Modifier on/off . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ23

Modifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Modulation effect type . . . . . . . . . . . . . . . . . . . .

ƒ46

Modulation effects . . . . . . . . . . . . . . . . . . . . . . . .

Modulation wheel 2 assign . . . . . . . . . . . . . . . . .

ƒ156

Mono delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ53

Navigation aids . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ11

Octave switch hold . . . . . . . . . . . . . . . . . . . . . . .

ƒ153

Output jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

188

Feature Reference

●

Appendix

Velocity curve . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ157

Vibrato envelope . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ135

Vibrato envelope key scaling . . . . . . . . . . .

ƒ137-140

Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ69

Voice directory . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voice list, abbreviated . . . . . . . . . . . . . . . . . . . . .

Voice mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ32

Voice name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ31

Voice number buttons . . . . . . . . .

Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pitch bend mode . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ35

Pitch change . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ49

Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ67

Pitch wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Play-mode display . . . . . . . . . . . . . . . . . .

Polyphony control . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ36

Portamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ40

Power cord socket . . . . . . . . . . . . . . . . . . . . . . . . .

Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power-on procedure . . . . . . . . . . . . . . . . . . . . . . .

Pre-programmed voices, loading . . . . . . . . . . . . .

Pressure envelope . . . . . . . . . . . . . . . . . . . . . . . .

ƒ129

Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ65

Quick editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ19

Receive channel . . . . . . . . . . . . . . . . . . . . . . . . . ƒ155

Resonator . . . . . . . . . . . . . . . . . . . . . . . .

Reverb effects . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ60

Scream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ72

Selecting & editing parameters . . . . . . . . . . . . . . ƒ12

Sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ184

Store button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Store function . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ28

Sustain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ35

Throat formant . . . . . . . . . . . . . . . . . . . . . . . . ƒ75, 91

Throat formant key scaling . . . . . . . . . . . . . .

ƒ93-97

Time calculation, musical . . . . . . . . . . . . . . . . . . .

ƒ59

Tonguing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ70

Touch EG time . . . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ36

Transmit channel . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ155

Trigger mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ƒ85

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .

ƒ178

189

Feature Reference

●

Appendix

Index

SY04

MIDDLE & SOUTH AMERICA

MEXICO

Yamaha De Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRASIL

Yamaha Musical Do Brasil LTDA.

Ave. Reboucas 2636, São Paulo, Brasil

Tel: 55-11 853-1377

PANAMA

Yamaha De Panama S.A.

Edificio Interseco, Calle Elvira Mendez no.10,

Piso 3, Oficina #105, Ciudad de Panama, Panama

Tel: 507-69-5311

OTHER LATIN AMERICAN COUNTRIES

AND CARIBBEAN COUNTRIES

Yamaha Music Latin America Corp.

6101 Blue Lagoon Drive, Miami, Florida 33126,

U.S.A.

Tel: 305-261-4111

EUROPE

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 0908-366700

IRELAND

Danfay Limited

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY/SWITZERLAND

Yamaha Europa GmbH.

Siemensstraße 22-34, D-2084 Rellingen, F.R. of

Germany

Tel: 04101-3030

AUSTRIA/HUNGARY/SLOVENIA/

ROMANIA/BULGARIA

Yamaha Music Austria GesmbH.

Schleiergasse 20, A-1100 Wien Austria

Tel: 0222-60203900

THE NETHERLANDS

Yamaha Music Benelux B.V.,

Verkoop Administratie

Kanaalweg 18G, 3526KL, Utrecht, The Netherlands

Tel: 030-828411

BELGIUM/LUXEMBOURG

Yamaha Music Benelux B.V.,

Brussels-office

Keiberg Imperiastraat 8, 1930 Zaventem, Belgium

Tel: 02-7258220

HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2445

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha

ou au distributeur le plus proche de vous figurant dans la liste suivante.

FRANCE

Yamaha Musique France,

Division Instruments Electroniques et de Scène

BP 70-77312 Marne-la-Valée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.,

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN

Yamaha-Hazen Electronica Musical, S.A.

Jorge Juan 30, 28001, Madrid, Spain

Tel: 91-577-7270

PORTUGAL

Valentim de Carvalho CI SA

Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,

Portugal

Tel: 01-443-3398/4030/1823

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J.A. Wettergrens gata 1, Box 30053, 400 43

Göteborg, Sweden

Tel: 031-496090

DENMARK

YS Copenhagen Liaison Office

Finsensvej 86, DK-2000 Frederiksberg, Denmark

Tel: 31-87 30 88

FINLAND

Fazer Music Inc.

Aleksanterinkatu 11, SF 00100 Helsinki, Finland

Tel: 0435 011

NORWAY

Narud Yamaha AS

Østerndalen 29, 1345 Østerås

Tel: 02-24 47 90

ICELAND

Páll H. Pálsson

P.O. Box 85, 121 Reykjavik, Iceland

Tel: 01-19440

EAST EUROPEAN COUNTRIES

(Except HUNGARY)

Yamaha Europa GmbH.

Siemensstraße 22-34, D-2084 Rellingen, F.R. of

Germany

Tel: 04101-3030

ASIA

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 730-1098

INDONESIA

PT. Yamaha Music Indonesia(Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Cosmos Corporation

#131-31, Neung-Dong, Sungdong-Ku, Seoul

Korea

Tel: 02-466-0021~5

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

16-28, Jalan SS 2/72, Petaling Jaya, Selangor,

Malaysia

Tel: 3-717-8977

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. BOX 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

Blk 17A Toa Payoh #01-190 Lorong 7

Singapore 1231

Tel: 354-0133

TAIWAN

Kung Hsue She Trading Co., Ltd.

No. 322, Section 1, FuHsing S. Road,

Taipei 106, Taiwan. R.O.C.

Tel: 02-709-1266

THAILAND

Siam Music Yamaha Co., Ltd.

865 Phornprapha Building, Rama I Road,

Patumwan, Bangkok 10330, Thailand

Tel: 2-215-3443

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2311

AFRICA

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2311

MIDDLE EAST

TURKEY/CYPRUS

Yamaha Musique France, Division Export

BP 70-77312 Marne-la-Valée Cedex 2, France

Tel: 01-64-61-4000

OTHER COUNTRIES

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2311

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

17-33 Market Street, South Melbourne, Vic. 3205,

Australia

Tel: 3-699-2388

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa, Auckland,

New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

International Marketing Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430

Tel: 053-460-2311

Yamaha VL-1 El manual del propietario

Marca: Yamaha

Modelo: VL-1

Categoría: Pianos digitales

Tipo: El manual del propietario

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

français: Yamaha VL-1 Le manuel du propriétaire
italiano: Yamaha VL-1 Manuale del proprietario
English: Yamaha VL-1 Owner's manual
Deutsch: Yamaha VL-1 Bedienungsanleitung
русский: Yamaha VL-1 Инструкция по применению
Nederlands: Yamaha VL-1 de handleiding
português: Yamaha VL-1 Manual do proprietário
dansk: Yamaha VL-1 Brugervejledning
polski: Yamaha VL-1 Instrukcja obsługi
čeština: Yamaha VL-1 Návod k obsluze
svenska: Yamaha VL-1 Bruksanvisning
Türkçe: Yamaha VL-1 El kitabı
suomi: Yamaha VL-1 Omistajan opas
română: Yamaha VL-1 Manualul proprietarului

Yamaha VL-1 El manual del propietario

Este manual también es adecuado para

Yamaha VL-1 El manual del propietario

En otros idiomas

Documentos relacionados