Yamaha RX-V671 Guía de instalación

Marca: Yamaha

Modelo: RX-V671

Tipo: Guía de instalación

El Yamaha RX-V671 es un receptor AV natural con sonido ideal para ver películas o escuchar música. Con el asistente YPAO puedes optimizar los ajustes de los altavoces en función de la sala, garantizando siempre el mejor sonido. Además, puedes conectar hasta 7 altavoces y un subwoofer para crear un sistema de sonido envolvente. También cuenta con múltiples entradas y salidas, incluyendo HDMI, ópticas, coaxiales, RCA y más.

Check that the following accessories are supplied with this product.

You need to separately prepare the following cables to build the system based on this

document.

■ Speaker cables (depending on the number of speakers)

■ HDMI cable (x 2)

■ Audio pin cable (x 1)

■ Digital optical cable (x 1) (unnecessary if your TV supports ARC)

1 Preparations

Accessories

Cables necessary for connections

■■

■

■ ■

■

■ ■

Remote control

YPAO microphone

Batteries (AAA, R03, UM-4) (x 2)

VIDEO AUX input cover

FM antenna

Easy Setup Guide

(this document)

Safety BrochureCD-ROM

(Owner’s Manual)

AM antenna

Insert into the remote control in the correct polarity (+/-).

Easy Setup Guide

English for U.S.A.

AV Receiver

“ ’ ”

2 En

Set up the speakers in the room by using the following diagram as a reference.

For information on other speaker systems, refer to “Owner’s Manual”.

2 Placing the speakers

5.1-channel system

60° 60°

80° 80°

7.1-channel system

Front speaker (L)

Front speaker (R)

Center speaker

Surround speaker (L)

Surround speaker (R)

Surround back speaker (L)

Surround back speaker (R)

Subwoofer

30 cm (1 ft) or more

80° 80°

60° 60°

En 3

Connecting speaker cables

Speaker cables have two wires. One is for connecting

the negative (-) terminal of the unit and the speaker, and

the other is for the positive (+) terminal. If the wires are

colored to prevent confusion, connect the black wire to

the negative and the other wire to the positive.

Remove approximately

10 mm of insulation from

the ends of the speaker

cable, and twist the bare

wires of the cable

together firmly.

Loosen the speaker

terminal.

Insert the bare wires of the cable into the gap on the

side (upper right or bottom left) of the terminal.

Tighten the terminal.

Using a banana plug

Tighten the speaker

terminal.

Insert a banana plug into

the end of the terminal.

Connect the front speakers ( / )

to the FRONT ( / ) terminals.

Connect the center speaker ( ) to the

CENTER terminal.

3 Connecting the speakers/subwoofer

• This unit is configured for 8-ohm speakers at the factory. When

connecting 6-ohm speakers, set the speaker impedance of this

unit to “6 Ω MIN”. For details, see “Setting the speaker

impedance” (p.16) in “Owner’s Manual”.

• Use a subwoofer equipped with built-in amplifier.

• Remove the power cable of this unit from an AC wall outlet and

turn off the subwoofer before connecting the speakers.

• Be careful that the core of the speaker cable does not touch

anything or come into contact with the metal areas of this unit.

This may damage this unit or the speakers. If the speaker

cables short circuit, “CHECK SP WIRES” will appear on the

front display when this unit is turned on.

FRONT

– (black)

+ (red)

RON

Banana plug

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

R LR

SINGLE

SUBWOOFER

SINGLE

ZONE 2/

PRESENCE

EXTRA SP

This unit (rear)

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

R LR

SINGLE

SUBWOOFER

SINGLE

ZONE 2/

PRESENCE

EXTRA SP

This unit (rear)

4 En

Connect the surround speakers ( /

) to the SURROUND ( / )

terminals.

Connect the subwoofer ( ) to the

SUBWOOFER jack.

Use an audio pin cable to

connect the subwoofer

().

Connect the surround back speakers ( /

) to the SURROUND BACK ( / )

terminals.

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

R LR

SINGLE

SUBWOOFER

SINGLE

ZONE 2/

PRESENCE

EXTRA SP

This unit (rear)

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

R LR

SINGLE

SUBWOOFER

SINGLE

ZONE 2/

PRESENCE

EXTRA SP

This unit (rear)

For 7.1-channel system

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

R L R

SINGLE

SUBWOOFER

SINGLE

ZONE 2/

PRESENCE

EXTRA SP

R L

This unit (rear)

Audio pin cable

En 5

4 Connecting the external devices

MAIN ZONE

ZONE2 ZONE CONTROL INFO MEMORY PRESET CATEGORY

FM AM

PURE DIRECT

VOLUME

VIDEOHDMI IN L AUDIO R

VIDEO AUX

STRAIGHTTONE CONTROL

DVD

TV CD RADIO

YPAO MIC

USB

PHONES

SILENT CINEMA iPod/iPhone

PROGRAM

SCENE

INPUT

NATURAL SOUND AV RECEIVER RX-V671

TUNING/CH

COMPONENT

VIDEO

+12V

0.1A MAX.

TRIGGER OUT

DOCK NETWORK

FMAM

75Ω

ANTENNA

AUDIO 2AUDIO 1

AV 6AV 5AV 4AV 3

(

)(

)

VIDEO

AV 2AV 1

COAXIAL OPTICALCOAXIALOPTICAL

OUT

COMPONENT

VIDEO

HDMI OUT

ARC

HDMI 1

(BD/DVD)

HDMI 2 HDMI 3 HDMI 4 HDMI 5

MONITOR OUT

OUT

REMOTE

ZONE 2

OUT

SUBWOOFER

AUDIO

OUT

SPEAKERS

FRONT CENTER SURROUND SURROUND BACK/BI–AMP

ZONE 2/

PRESENCE

EXTRA SP

RL R

SINGLE

SIRIUS

HDMIOPTICAL

HDMI

HDMI 1

(BD/DVD)

HDMI

(

)

OPTICAL

AV 4

HDMI OUT

ARC

HDMI

Audio out

(optical)

HDMI in HDMI out

BD/DVD player

HDMI1 jackHDMI OUT jack

AV4 (OPTICAL) jack

Turn on this unit

This unit (rear)

This unit (front)

To an AC

wall outlet

Connect the external devices to this unit.

Connect the BD/DVD player and this unit with an

HDMI cable.

If the BD/DVD player is currently connected to the

TV directly with an HDMI cable, disconnect the

cable from the TV and connect it to this unit.

Connect the TV and this unit with another HDMI

cable.

Connect the TV and this unit with a digital optical

cable.

This connection is required to play back TV audio

on this unit. If your TV supports ARC (Audio Return

Channel), this connection is unnecessary.

Connect the power cable to an AC wall outlet.

• For information on how to connect radio antennas or other

external devices, see “SETUP” in “Owner’s Manual”.

Turn on this unit, TV and BD/DVD player.

With the remote control of the TV, switch

the TV input to display the video from this

unit.

The connections are complete. Move to the next

page to optimize the speaker settings.

6 En

By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker

connections and distances from the listening position, and optimizes the speaker settings such as volume balance and

acoustic parameters to suit your room.

Preparing for YPAO

Optimizing the speaker settings automatically (YPAO)

• During the measuring process, the test tones are output at high volume. Take care

that the test tone does not frighten small children. Also, refrain from using this

function at night when it may be a nuisance to others.

• During the measuring process, you cannot adjust the volume.

• During the measuring process, keep the room as quiet as possible.

• Do not connect headphones.

• If your subwoofer supports the auto-standby function, disable it.

• YPAO measurement is not performed correctly when any obstacles are in the room.

• During the measuring process (about 3 minutes), keep stuff in the corners or

remove it from the room.

Connect the YPAO microphone to the

YPAO MIC jack on the front panel.

The following screen appears on the TV.

• To cancel the operation, disconnect the YPAO microphone

before starting the measurement.

To start the measurement, use the cursor

keys to select “Measure” and press

ENTER.

The measurement will start in 10 seconds.

The following screen appears on the TV when

the measurement finishes.

• If any error message (such as E-1) or warning message (such

as W-2) appears, see “Error messages” (p.36) or “Warning

messages” (p.37) in “Owner’s Manual”.

• If the warning message “W-1:Out of Phase” appears, see “If

‘W-1:Out of Phase’ appears” (next page).

VOLUME HIGH CUT

CROSSOVER/

MIN MAXMIN MAX

SCENE

RETURN

VOLUME

SUR. DECODE

STRAIGHT

ENHANCER

SLEEP PURE DIRECT

HDMI

1234

V-AUX

INFO

MEMORY

PRESET

MOVIE MUSIC

DVD

RADIO

MUTE

ENTER

7856

1234

MODE

ENT

TV VOL TV CH

TOP

POP-UP

DISPLAY

SOURCE

MAIN

ZONE 2

RECEIVER

CODE SET

INPUT

MUTE

DOCK

AUDIO

OPTION

ON SCREEN

1234

TUNER NET USB

TUN./CH

SIRIUS

HOLD

FM AM

CATEGORY

LUME

UR. DE

TRAI

ENHAN

LEEP

URE DIRE

HDMI

AUX

VIE M

DVD

RADI

ODE

ENT

V V

TOP

P-U

ENU

PLA

MAIN

ZONE

EIVE

INF

INPUT

MUTE

DOC

UDI

PTI

REEN

TUNER

NET

/CH

IRIU

ATE

This unit (front)

Turned on the subwoofer and set

the volume to half. If the

cross-over frequency is

adjustable, set it to maximum.

Place the YPAO microphone at ear

height in your listening position. We

recommend using a tripod to adjust the

height. You can use the tripod screws to

fix the microphone in place.

YPAO microphone

Listening position

Ear height

Cursor keys

ENTER

RETURN

En 7

Use the cursor keys to select

“Save/Cancel” and press ENTER.

Use the cursor keys to select “SAVE” and

press ENTER.

Disconnect the YPAO microphone from

this unit.

Now optimization of the speaker settings is

complete.

Follow the procedure below to check the speaker

connections.

Depending on the type of speakers or room

environment, this message may appear even if the

speakers are connected correctly.

Use the cursor keys to select “Result” and press ENTER.

Use the cursor keys to select “Wiring”.

Check the cable connections (+/-) of the speaker

indicated with “Reverse”.

If the speaker is connected correctly:

You can save the current settings.

Press RETURN and proceed to step 3.

If the speaker is connected incorrectly:

Turn off this unit, reconnect the speaker cable, and then

try YPAO measurement again.

• Since the YPAO microphone is sensitive to heat, do not place

the microphone in any place where it will be subjected to direct

sunlight or high temperatures (top of an AV equipment, etc).

If “W-1: Out of Phase” appears

Now let’s play back a BD/DVD.

We recommend playing back multichannel audio (5.1-

channel or more) to feel surround sound produced by

this unit.

Press HDMI1 to select “HDMI1” as the

input source.

Start playback on the BD/DVD player.

Press STRAIGHT repeatedly to select

“STRAIGHT”.

• When “STRAIGHT” (straight decode) is enabled, each

speaker produces each channel audio signal directly (without

sound field processing). If you play back 5.1-channel audio on

the 7.1-channel system, no sounds will be heard from the

surround back speakers.

Press VOLUME to adjust the volume.

Now the basic setup procedure is complete.

Only the front speakers work on multichannel audio

Check the digital audio output setting on the BD/DVD

player.

It may be set to output 2-channel audio (PCM, etc.) only.

No sound is heard from a specific speaker

See “Troubleshooting” (p.109) in “Owner’s Manual”.

6 Playing back a BD/DVD

VOLUME

SUR. DECODE

STRAIGHT

ENHANCER

SLEEP PURE DIRECT

HDMI

1234

V-AUX

INFO

MEMORY

PRESET

MOVIE MUSIC

DVD

RADIO

MUTE

7856

1234

MODE

ENT

TV VOL TV CH

POP-UP

SOURCE

MAIN

ZONE 2

RECEIVER

CODE SET

INPUT

MUTE

DOCK

AUDIO

ON SCREEN

1234

TUNER NET USB

TUN./CH

SIRIUS

HOLD

FM AM

Yamaha RX-V671 Guía de instalación

Marca: Yamaha

Modelo: RX-V671

Tipo: Guía de instalación

Descargar PDF

informe

En otros idiomas

français: Yamaha RX-V671 Guide d'installation
italiano: Yamaha RX-V671 Guida d'installazione
English: Yamaha RX-V671 Installation guide
Deutsch: Yamaha RX-V671 Installationsanleitung
русский: Yamaha RX-V671 Инструкция по установке
Nederlands: Yamaha RX-V671 Installatie gids
português: Yamaha RX-V671 Guia de instalação
dansk: Yamaha RX-V671 Installationsvejledning
polski: Yamaha RX-V671 Instrukcja instalacji
čeština: Yamaha RX-V671 instalační příručka
svenska: Yamaha RX-V671 Installationsguide
Türkçe: Yamaha RX-V671 Yükleme Rehberi
suomi: Yamaha RX-V671 Asennusohje
română: Yamaha RX-V671 Ghid de instalare

Yamaha RX-V671 Guía de instalación

Yamaha RX-V671 Guía de instalación

En otros idiomas

Documentos relacionados