Motorola EDGE-WC-BK Wireless Charging Case Guía del usuario
- Tipo
- Guía del usuario
Wireless Charging Case
User Guide
(EDGE-WC-BK)
es (pp.04- 05)
de (pp. 1 0- 1 1 )
f r (pp.06-07)
i t (pp. 1 2 - 1 3)
en (pp.0 1 -03)
p t (pp.08-09)
Features:
1. Built in 10W Qi compatible receiver, 5V/1A, 9V/1.1A.
2. Wired USB-C input accepts 5V/3A, 9V/2A, QC3.0 & USB-PD 18W
TurboPower pass through wired charging.
Installation:
1. Attach your Motorola Edge
USB-C charge port to the
USB-C connector in the
wireless charging case.
2. Align the bottom of the phone
with the bottom of the case
and push in.
3. Push the rest of the phone into
the case.
For wireless charging:
Using a Qi wireless charging pad
1. Align the Motorola M-logo with the
center of a wireless charging pad.
2. Place the back of the case onto a
Qi wireless charging pad.
3. Ensure the wireless charging pad
is charging.
4. Your device will begin to charge.
Note: Wireless charging pad and
USB-C cable are sold separately.
For direct charging:
Connect your charger and USB-C
cable to the USB-C port at the
bottom of the phone case.
Note: Wall charger and USB-C
cable are sold separately.
Uninstallation:
1. Keep the bottom of the phone and case connected, slightly release
the top of the Motorola edge phone for just enough to get out
of the frame of the case top.
2. Keep the alignment of the bottom of the phone with the bottom of
the case and pull the phone up from the case to disengage the
USB-C charge port from the USB-C connector of case.
FCC Notice to User
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
See 47 CFR Sec. 15.105(b). These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject
English
01
Features:
1. Built in 10W Qi compatible receiver, 5V/1A, 9V/1.1A.
2. Wired USB-C input accepts 5V/3A, 9V/2A, QC3.0 & USB-PD 18W
TurboPower pass through wired charging.
Installation:
1. Attach your Motorola Edge
USB-C charge port to the
USB-C connector in the
wireless charging case.
2. Align the bottom of the phone
with the bottom of the case
and push in.
3. Push the rest of the phone into
the case.
For wireless charging:
Using a Qi wireless charging pad
1. Align the Motorola M-logo with the
center of a wireless charging pad.
2. Place the back of the case onto a
Qi wireless charging pad.
3. Ensure the wireless charging pad
is charging.
4. Your device will begin to charge.
Note: Wireless charging pad and
USB-C cable are sold separately.
For direct charging:
Connect your charger and USB-C
cable to the USB-C port at the
bottom of the phone case.
Note: Wall charger and USB-C
cable are sold separately.
Uninstallation:
1. Keep the bottom of the phone and case connected, slightly release
the top of the Motorola edge phone for just enough to get out
of the frame of the case top.
2. Keep the alignment of the bottom of the phone with the bottom of
the case and pull the phone up from the case to disengage the
USB-C charge port from the USB-C connector of case.
FCC Notice to User
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
See 47 CFR Sec. 15.105(b). These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject
02
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada Notice to User, RSS-Gen Statement
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licenceexempt RSS(s). Operation is subject to the following two
conditions: (1) This device may not cause interference. (2) This device
must accept any interference, including interference that may cause
undesired operation of the device. This device complies with ICES-003
requirements for Class B ITE (Information Technology Equipment). CAN
ICES-3 (B)/NMB-3(B)
Recycling of Waste Electrical and Electronic Equipment (WEEE)
This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other household
household waste. Customers or end-users should contact their
local equipment supplier or service center for information on
the waste collection system in their country.
For warranty and more information:
motorolachargers.com/phonecases/
03
04
Caracteristicas:
1. Receptor compatible con Qi de 10W integrado, 5V/1A, 9V/1,1A.
2. La entrada con cable USB-C acepta el paso de 5V/3A, 9V/2A, QC3.0
y USB-PD 18W TurboPower a través de la carga con cable.
Instalación:
1. Conecte su puerto de carga
Motorola Edge USB-C al
conector USB-C en la funda
de carga inalámbrica.
2. Alinee la parte inferior del
teléfono con la parte inferior
de la funda y presione.
3. Empuje el resto del teléfono
en la funda.
Para carga inalámbrica:
Usando una base de carga inalámbrica Qi
1. Alinee el logotipo M de Motorola con el
centro de la base de carga inalámbrica.
2. Coloque la parte posterior del estuche
en una base de carga inalámbrica Qi.
3. Asegúrese de que la base de carga
inalámbrica se esté cargando.
4. Su dispositivo comenzará a cargarse.
Nota: la base de carga inalámbrica y el
cable USB-C se venden por separado.
Para carga directa:
Conecte su cargador y el cable
USB-C al puerto USB-C en la
parte inferior de la funda del
teléfono.
Nota: el cargador de pared y el
cable USB-C se venden por separado.
Español
05
Desinstalación:
1. Mantenga la parte inferior del teléfono y la funda conectadas, suelte
ligeramente la parte superior del teléfono Motorola edge lo suficiente
para salir del marco de la parte superior de la funda.
2. Mantenga la alineación de la parte inferior del teléfono con la parte
inferior de la funda y extraiga el teléfono de la funda para desconectar
el puerto de carga USB-C del conector USB-C de la funda.
Reciclaje de residuos de aparatos eléctricos y electrónicos (RAEE)
Este símbolo en el producto o en su empaque indica que este
producto no debe desecharse junto con la basura doméstica.
Los clientes o los usuarios finales deben comunicarse con su
proveedor de equipo local o con su centro de servicio para
obtener información sobre el sistema de recolección de
residuos en su país.
Para garantía y más información:
motorolachargers.com/phonecases/
06
Français
Fonctionnalités:
1. Récepteur compatible Qi 10W intégré, 5V/1A, 9V/1,1A.
2. L'entrée USB-C filaire accepte le passage 5V/3A, 9V/2A, QC3.0 et
USB-PD 18W TurboPower via une charge filaire.
Installation:
1. Branchez le port de charge
USB-C de votre Motorola Edge
sur le connecteur USB-C de la
dcoque de chargement sans fil.
2. Alignez le bas du téléphone
avec le bas de la coque et
poussez-le.
3. Poussez le reste du téléphone
dans la coque.
Pour le chargement sans fil:
Utilisation d'une coque de chargement sans fil Qi
1. Alignez le logo M de Motorola avec le
centre d'un base de charge sans fil.
2. Placez l'arrière de la coque sur un base
de charge sans fil Qi.
3. Assurez-vous que la base de charge
sans fil est en cours de chargement.
4. Votre appareil commencera à se charger.
Remarque: la base de charge sans fil et
le câble USB-C sont vendus séparément.
Pour le chargement direct:
Connectez votre chargeur et
votre câble USB-C au port USB-C
en bas de la coque du téléphone.
Remarque: le chargeur mural et le
câble USB-C sont vendus séparément.
07
Désinstallation:
1. Gardez le bas du téléphone et la coque connectés, relâchez
légèrement le supérieur du téléphone Motorola Edge juste assez pour
sortir du cadre supérieur de la conque.
2. Gardez l'alignement du bas du téléphone avec le bas de la conque et
tirez le téléphone vers le supérieur de la conque pour désengager le
port de charge USB-C du connecteur USB-C de la conque.
Avis d’Industrie Canada aux utilisateurs
Cet appareil est conforme aux normes CNR d'Industrie Canada pour les
appareils radio exempt de license. Son utilisation est assujettie aux deux
conditions suivantes: (1) l’appareil ne doit pas causer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris les
interférences pouvant entraîner un fonctionnement non souhaité de
l’appareil. Cet appareil est conforme à la norme NMB-003 pour les
équipments Informatiques (EI) de class B. CAN ICES-3 (B)/NMB-3(B)
Recyclage des déchets d’équipements électriques et électroniques
(DEEE)
Ce symbole sur le produit ou sur son emballage indique que ce
produit ne doit pas être jeté avec vos autres déchets ménagers.
Les clients ou les utilisateurs finaux doivent contacter leur
fournisseur local d’équipement ou leur centre de service local
pour obtenir des informations sur le système de collecte des
déchets.
Pour la garantie et plus d'informations:
motorolachargers.com/phonecases/
08
Português
Características:
1. Construído com receptor 10W Qi, compatível com 5V/1A, 9V/1,1A.
2. A entrada USB-C aceita carregamento com fio de 5V/3A, 9V/2A,
QC3.0 e USB-PD 18W TurboPower.
Instalação:
1. Conecte a porta USB-C do
Motorola Edge ao conector
USB-C da capa de
carregamento sem fio.
2. Alinhe a parte inferior do
telefone com a parte inferior
da capa e empurre.
3. Empurre o resto do telefone
para dentro da capa.
Para carregamento sem fio:
Usando uma base carregadora sem fio Qi
1. Alinhe o logotipo M da Motorola com o
centro de uma base carregadora sem fio.
2. Coloque a parte traseira da capa em contato
com a base carregadora sem fio Qi.
3. Certifique-se de que a base de
carregadora sem fio esteja carregando.
4. Seu dispositivo começará a carregar.
Nota: O cabo e a base de carregadora
sem fio são vendidos separadamente.
Para carregamento direto:
Conecte um carregador com
cabo USB-C à porta USB-C na
parte inferior da capa do telefone.
Nota: O carregador de parede e o
cabo USB-C são vendidos separadamente.
09
Desinstalação:
1. Mantenha a parte inferior do telefone e a capa conectados. Solte
levemente a capa da parte superior do telefone Motorola Edge,
apenas o suficiente para sair do telefone.
2. Mantenha o alinhamento na parte inferior do telefone com a parte
inferior da capa e deslize o telefone para a parte superior da capa, para
desencaixar a porta USB-C do telefone da porta USB-C da capa.
Pelo Brasil:
Este equipamento não tem direito à
proteção contra interferência prejudicial e
não pode causar interferência em
sistemas devidamente autorizados.
Diretrizes sobre Resíduos de Equipamentos Elétricos e Eletrônicos
(REEE)
Este símbolo, no produto ou em sua embalagem, indica que
este produto não deve ser descartado com outros resíduos
domésticos. Os clientes ou usuários finais do produto devem
entrar em contato com o fornecedor local do produto, ou um
centro de serviços autorizado, para obter informações sobre o
sistema de descarte de lixo eletrônico.
Para garantia e mais informações:
motorolachargers.com/phonecases/
www.anatel.gov.br
10
Eigenschaften:
1. Eingebauter 10W Qi-kompatibler Empfänger, 5V/1A, 9V/1,1A.
2. Der kabelgebundene USB-C-Eingang akzeptiert 5V/3A, 9V/2A, QC3.0
und USB-PD 18W TurboPower-Durchgang durch kabelgebundenes
Laden.
Installation:
1. Schließen Sie Ihren Motorola
Edge USB-C-Ladeanschluss
an den USB-C-Anschluss der
kabellosen Ladehülle an.
2. Richten Sie die Unterseite des
Telefons an der Unterseite der
Hülle aus und drücken Sie sie
hinein.
3. Schieben Sie den Rest des Telefons in die Hülle.
Zum kabellosen Laden:
Verwenden eines kabellosen Qi-Ladepads
1. Richten Sie das Motorola M-Logo an der
Mitte eines kabellosen Ladepads aus.
2. Legen Sie die Rückseite der Hülle auf ein
kabelloses Qi-Ladegerät.
3. Stellen Sie sicher, dass das kabellose
Ladegerät geladen wird.
4. Ihr Gerät wird aufgeladen.
Bemerkung: Das kabellose Ladepad und
das USB-C-Kabel sind separat erhältlich.
Zum direkten Laden:
Schließen Sie Ihr Ladegerät und
das USB-C-Kabel an den
USB-C-Anschluss an der
Unterseite der Telefonhülle an.
Bemerkung: Ladegerät und USB-C-Kabel sind separat erhältlich.
Deutsch
1 1
Deinstallation:
1. Lassen Sie die Unterseite des Telefons und der Hülle verbunden, und
lassen Sie die Oberseite des Motorola Edge-Telefons leicht los, damit
sie gerade so weit aus dem Rahmen der Hülle herausragt.
2. Behalten Sie die Ausrichtung der Unterseite des Telefons mit der
Unterseite der Hülle bei und ziehen Sie das Telefon aus der Hülle
heraus, um den USB-C-Ladeanschluss vom USB-C-Anschluss der
Hülle zu trennen.
Recycling von Elektro-und Elektronik-Altgeräten
(Waste Electrical and Electronic Equipment, WEEE)
Dieses Symbol auf dem Produkt oder auf der Verpackung
zeigt an, dass dieses Produkt nicht mit Ihrem sonstigen
Hausmüll entsorgt werden darf. Kunden oder Endverbraucher
sollten sich an ihren örtlichen Anbieter oder ihr Service-Center
wenden, um Informationen über das Abfallsammelsystem zu
erhalten.
Für Garantie und weitere Informationen:
motorolachargers.com/phonecases/
12
Italiano
Caratteristiche:
1. Ricevitore compatibile Qi da 10W integrato, 5V/1A, 9V/1,1A.
2. L'ingresso USB-C cablato accetta il passaggio 5V/3A, 9V/2A, QC3.0 e
USB-PD 18W TurboPower attraverso la ricarica cablata.
Installazione:
1. Collegare la porta di ricarica
USB-C Motorola Edge al
connettore USB-C nella
custodia di ricarica wireless.
2. Allineare la parte inferiore del
telefono con la parte inferiore
della custodia e spingere.
3. Spingere il resto del telefono
nella custodia.
Per la ricarica wireless:
Utilizzando una base di ricarica wireless Qi
1. Allineare il logo Motorola M con il centro
di una base di ricarica wireless.
2. Posiziona il retro della custodia su una
base di ricarica wireless Qi.
3. Verificare che la base di ricarica wireless
sia in carica.
4. Il dispositivo inizierà a caricarsi.
Nota: la base di ricarica wireless e il cavo
USB-C sono venduti separatamente.
Per il caricamento diretto:
Collega il caricabatterie e il cavo
USB-C alla porta USB-C nella
parte inferiore della custodia del
telefono.
Nota: il caricatore da muro e il cavo
USB-C sono venduti separatamente.
13
Disinstallazione:
1. Tenere la parte inferiore del telefono e la custodia collegate, rilasciare
leggermente la parte superiore del telefono Motorola Edge per quel
tanto che basta per uscire dalla cornice della parte superiore della
custodia.
2. Mantenere l'allineamento della parte inferiore del telefono con
la parte inferiore della custodia e tirare il telefono verso l'alto dalla
custodia per sganciare la porta di ricarica USB-C dal connettore USB-C
della custodia.
Riciclaggio dei rifiuti di apparecchiature elettriche ed elettroniche
(RAEE)
Questo simbolo sul prodotto o sulla sua confezione indica che
il prodotto non deve essere smaltito insieme agli altri rifiuti
domestici. I clienti o gli utenti finali devono contattare il
proprio fornitore di apparecchiature o centro servizi locale per
informazioni sul sistema di raccolta dei rifiuti.
Per garanzia e ulteriori informazioni:
motorolachargers.com/phonecases/
14
motorola.com Printed in China
Rev. 202010-01
Manufactured, distributed or sold by Salom Ltd., ocial licensee for this product. MOTOROLA and
Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC, and are
used under license. All other trademarks are the property of their respective owners.
© 2020 Motorola Mobility LLC. All rights reserved.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
