Yamaha DSP-A1092 El manual del propietario

Marca: Yamaha

Modelo: DSP-A1092

Categoría: Receptores AV

Tipo: El manual del propietario

Natural Sound AV Amplifire

Amplificateur audiovisuel “Son Naturel”

Natural Sound AV-Verstärker

Natural Sound AV-förstärkare

Amplificatore AV a suono naturale

Amplificador AV de Sonido Natural

Natural Sound AV Versterker

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

POWER

VCR 2 DVD

LDVCR 1

VIDEO AUX

TAPE (MD) TV/DBS

TUNER

PHONO

VOLUME

–dB

SPEAKERSPHONES

OFF

BASS

EXTENSION

TONE

BYPASS

BASS TREBLE BALANCE

VIDEO AUX

S VIDEO VIDEO L AUDIO R

DELAY

SWFR

EFFECT

PROGRAM

SET

NATURAL SOUND AV AMPLIFIER

DSP–A1092

CINEMA DSP

7ch

VCR 2

VIDEO AUX

REC OUT

VCR 1

TV/DBS

PHONO

TUNER

DVD/LD

SOURCE

TAPE (MD)

Congratulations!

You are the proud owner of a Yamaha Digital Sound Field Processing (DSP) System—an

extremely sophisticated audio component. The DSP system takes full advantage of Yamaha’s

undisputed leadership in the field of digital audio processing to bring you a whole new world of

listening experiences. Follow the instructions in this manual carefully when setting up your system,

and the DSP system will sonically transform your room into a wide range of listening

environments—anything from a famous concert hall to a cozy jazz club. In addition, you get

incredible realism from Dolby-Surround encoded video sources using the built-in Dolby Pro Logic

Surround Decoder and Dolby Digital (AC-3) Decoder.

Seven built-in channels of amplification on this model mean that no additional amplifiers are

required to enjoy advanced digital sound field processing.

Rather than tell you about the wonders of digital sound field processing, however, let’s get right

down to the business of setting up the system and trying out its many capabilities. Please read this

operation manual carefully and store it in a safe place for later reference.

English

1. AVOID EXCESSIVE HEAT, HUMIDITY, DUST

AND VIBRATION

Keep the unit away from locations where it is likely to be

exposed to high temperatures or humidity—such as

near radiators, stoves, etc. Also avoid locations which

are subject to excessive dust accumulation or vibration

which could cause mechanical damage.

2. INSTALL THE UNIT IN WELL-VENTILATED

CONDITION

The openings on the cabinet assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the cabinet will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in well-ventilated

condition. Make sure to allow a space of at least 10

cm behind, 20 cm on the both sides and 30 cm above

the top panel of the unit. Otherwise it may not only

damage the unit, but also cause fire.

3. KEEP THE AC POWER PLUG

DISCONNECTED DURING VACATION ETC.

When not planning to use this unit for long periods of

time (ie., vacation, etc.), disconnect the AC power

plug from the wall outlet.

4. AVOID PHYSICAL SHOCKS

Strong physical shocks to the unit can cause damage.

Handle it with care.

5. DO NOT OPEN THE UNIT OR ATTEMPT

REPAIRS OR MODIFICATIONS YOURSELF

This product contains no user-serviceable parts. Refer

all maintenance to qualified Yamaha service personnel.

Opening the unit and/or tampering with the internal

circuitry will make servicing difficult and will endanger

you and your unit.

6. MAKE SURE POWER IS OFF BEFORE

MAKING OR REMOVING CONNECTIONS

Always turn power OFF prior to connecting or

disconnecting cables. This is important to prevent

damage to the unit itself as well as other connected

equipment.

7. HANDLE CABLES CAREFULLY

Always plug and unplug cables—including the AC

cord—by gripping the connector, not the cord.

8. CLEAN WITH A SOFT DRY CLOTH

Never use solvents such as benzine or thinner to clean

the unit. Wipe clean with a soft, dry cloth.

9. USE THIS UNIT WITH THE CORRECT

VOLTAGE

The voltage to be used must be the same as that

specified on this unit. Using this unit with a higher

voltage than that which is specified is dangerous and

may result in a fire or other type of accident causing

damage. YAMAHA will not be held responsible for any

damage resulting from use of this unit with a voltage

other than that which is specified.

10.KEEP AWAY FROM TUNERS

Digital signals generated by the unit may interfere with

other equipment such as tuners, receivers or TVs. Move

the system farther away from such equipment if

interference is observed.

IMPORTANT!

Please record the model and serial number of your

unit in the space below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

Voltage Selector (General Model only)

The voltage selector on the rear panel of this unit

must be set for your local mains voltage

BEFORE plugging into the AC mains supply.

Voltages are 110/120/220/240 AC, 50/60 Hz.

WARNING

To reduce the risk of fire or electric shock, do not

expose this unit to rain or moisture.

For U.K. customers

If the socket outlets in the home are not suitable for

the plug supplied with this appliance, it should be cut

off and an appropriate 3 pin plug fitted. For details,

refer to the instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is

hazardous if engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT

The wires in the mains lead are coloured in

accordance with the following code.

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows. The wire which is coloured BLUE

must be connected to the terminal which is marked

with the letter N or coloured BLACK. The wire which is

coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the

earth terminal of the three pin plug.

The apparatus is not disconnected from the AC

power source as long as it is connected to the wall

outlet, even if the apparatus itself is turned off.

WARNING

Do not change the IMPEDANCE SELECTOR

switch setting while the power to this unit is

on, otherwise this unit may be damaged.

PRECAUTIONS & SAFETY INSTRUCTIONS

SWITCHED

AC OUTLETS

IMPEDANCE SELECTOR

VOLTAGE SELECTOR

I20W

MAX.

TOTAL

CENTER C OR D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 4

Ω

MIN./ SPEAKER

A B

: 8

Ω

MIN./ SPEAKER

FRONT EFFECT

: 6

Ω

MIN./ SPEAKER

CENTER C OR D: 8

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 8

Ω

MIN./ SPEAKER

A B

: 6

Ω

MIN./ SPEAKER

FRONT EFFECT

: 8

Ω

MIN./ SPEAKER

IMPEDANCE

SELECTOR

(General model)

PRECAUTIONS & SAFETY INSTRUCTIONS...................................1

GETTING STARTED ...........................................................................3

FEATURES ..........................................................................................5

SPEAKER SETUP.............................................................................10

CONTROLS & THEIR FUNCTIONS.................................................13

FRONT PANEL................................................................................13

DISPLAY PANEL.............................................................................16

CONNECTIONS.................................................................................17

REAR PANEL PARTS AND THEIR FUNCTIONS .........................17

REAR PANEL SWITCH AND CONTROL SETTINGS...................20

GENERAL INSTRUCTIONS FOR CONNECTIONS.....................20

CONNECTING AUDIO/VIDEO SOURCE EQUIPMENT

TO THIS UNIT.................................................................................21

CONNECTING SPEAKER SYSTEMS...........................................25

SELECTING THE OUTPUT MODES SUITABLE FOR YOUR

SPEAKER SYSTEM .......................................................................30

SPEAKER BALANCE ADJUSTMENT ............................................33

ADJUSTMENTS IN THE “SET MENU” MODE...............................35

GENERAL OPERATION...................................................................38

PLAYING A SOURCE.....................................................................38

RECORDING A SOURCE TO AUDIO/VIDEO TAPE

(OR DUBBING FROM A TAPE TO ANOTHER) ............................40

SELECTING SOUND FIELD PROGRAMS......................................42

CANCELING THE EFFECT SOUND.............................................43

DESCRIPTIONS OF THE SOUND FIELD PROGRAMS..............44

ADJUSTING DELAY TIME AND EACH SPEAKER OUTPUT

LEVEL..............................................................................................47

SETTING THE SLEEP TIMER..........................................................49

REMOTE CONTROL UNIT ...............................................................50

BASIC OPERATIONS (When the lid is open) ................................50

LEARNING NEW CONTROL FUNCTIONS (When the lid is open)

.........................................................................................................52

USING OPERATION CONTROL KEYS (When the lid is closed)

.........................................................................................................55

MACRO OPERATIONS (When the lid is closed) ...........................58

LEARNING A NEW FUNCTION.....................................................61

MAKING A NEW MACRO...............................................................63

CLEARING LEARNED FUNCTIONS.............................................64

TROUBLESHOOTING ......................................................................66

SPECIFICATIONS .............................................................................68

CONTENTS

English

GETTING STARTED

Unpacking

If you haven’t already done so, carefully remove this unit and its

accessories from the box and wrapping material. You should find the

unit itself and the following accessories.

Installing the Remote Control Unit Batteries

Since the remote control unit will be used for many of this unit’s

control operations, you should begin by installing the supplied

batteries.

1. Turn the remote control unit over and slide the battery

compartment cover downward in the direction of the arrow.

2. Insert the batteries (LR6, AA, UM-3 type), being careful to align

them with the polarity markings on the inside of the battery

compartment.

3. Close the battery compartment cover.

* After you insert batteries (or you exchange batteries with new

ones), press the RESET button before using the remote control

unit.

Remote control

User function stickers

Batteries

RESET button

Notes about the Remote Control Unit

● When you notice that remote control operation has become

erratic, or the distance from which the remote control will function

has decreased, it’s time to replace the batteries. Always replace all

batteries at the same time.

● This remote control uses an advanced, highly directional infrared

beam. Be sure to aim the remote control directly at the remote

control sensor on the main unit when operating.

Remote control transmitter operation range

Notes

●

There should be no large obstacles between the remote control

unit and the main unit.

●

If the remote control sensor is directly illuminated by strong

lighting (especially an inverter type of fluorescent lamp etc.), it

might cause the remote control unit to work incorrectly. In this

case, reposition the main unit to avoid direct lighting.

Open/close the control door

When it is not necessary to operate controls inside the control

door, close the door.

To open the door

To close the door

30°

Remote control

sensor

Within approximately

6 m (19.7 feet)

English

This unit incorporates a sophisticated, multi-program digital

sound field processor. The processor allows you to electronically

expand and change the shape of the audio sound field from both

audio and video sources, creating a theater-like experience in your

listening room. This unit has a total of 10 digital sound field

processor (DSP) modes. You can create an excellent audio sound

field by selecting a suitable sound field (this will, of course, depend

on what you will be listening to), and adding desired adjustments.

In addition, this unit incorporates a Dolby Pro Logic Surround

decoder and Dolby Digital (AC-3) decoder for multi-channel sound

reproduction of Dolby Surround encoded video sources. The

operation of the Dolby Pro Logic Surround or Dolby Digital (AC-3)

decoder can be controlled by selecting a corresponding DSP

program including combined operations of the Yamaha DSP and

the Dolby Pro Logic Surround or Dolby Digital (AC-3) decoder.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced

sound reproduction technology lets you get extremely close to the

sound of a live performance, but chances are you’ll still notice

something missing, the acoustic environment of the live concert

hall. Extensive research into the exact nature of the sonic

reflections that create the ambience of a large hall has made it

possible for Yamaha engineers to bring you this same sound in

your own listening room, so you’ll feel all the sound of a live

concert. What’s more, our technicians, armed with sophisticated

measuring equipment, have even made it possible to capture the

acoustics of a variety of actual concert halls, jazz clubs, theaters,

etc. from around the world, to allow you to accurately recreate any

one of these live performance environments, all in your own home.

FEATURES

Dolby Pro Logic Surround

This unit employs a Dolby Pro Logic Surround decoder similar

to professional Dolby Stereo decoders used in many movie

theaters. By using the Dolby Pro Logic Surround decoder, you can

experience the dramatic realism and impact of Dolby Surround

movie theater sound in your own home. Dolby Pro Logic employs a

four channel five speaker system. The Pro Logic Surround system

divides the input signal into four levels: the left and right main

channels, the center channel (used for dialog), and the rear

surround sound channels (used for sound effects, background

noise, and other ambient noises). The center channel allows

listeners seated in even less-than-ideal positions to hear the dialog

originating from the action on the screen while experiencing good

stereo imaging. Dolby Surround is encoded on the sound track of

pre-recorded video tapes, laser discs, and some TV/cable

broadcasts. When you play a source encoded with Dolby Surround

on this unit, the Dolby Pro Logic Surround decoder decodes the

signal and distributes the surround-sound effects.

This Dolby Pro Logic Surround Decoder employs a digital

signal processing system. This system improves the stability of

sound at each channel and crosstalk between channels, so that

positioning of sounds around the room is more accurate compared

with conventional analog signal processing systems.

In addition, this unit features a built-in automatic input balance

control. This always assures you the best performance without

manual adjustment.

Dolby Digital (AC-3)

The built-in Dolby Digital (AC-3) Decoder leads you into a

totally new sound experiences.

Dolby Digital (AC-3) is a new generation of multi-channel digital

audio technology, or the newest spatial sound processing format

developed for 35 mm film-movies by employing a new kind of low

bit-rate audio coding.

Dolby Digital (AC-3) is a digital surround sound system that

provides completely independent multi-channel audio to

consumers. In multi-channel form, Dolby Digital (AC-3) provides

five full range channels in what is sometimes referred to as a “3/2”

configuration: three front channels (left, center and right), plus two

surround channels. A sixth bass-only effect channel is also

provided for output of LFE (low frequency effect), or low bass

effects that are independent of other channels. This channel is

counted as 0.1, thus giving rise to the term 5.1 channels in total.

Compared to Dolby Pro Logic that is referred to a “3/1” system

(left front, center, right front and just one surround channel), Dolby

Digital (AC-3) features two surround channels, called stereo or

split surrounds, each offering the same full range fidelity as the

three front channels.

Sound of wide dynamic range reproduced by the five full range

channels presents listeners much excitement that has never been

experienced before. Precise sound orientation by the discrete

digital sound processing expands realism that the original movie

possesses.

English

Laser Disc is a home audio format that could benefit from

Dolby Digital (AC-3). In the near future, Dolby Digital (AC-3) will

also be applied to DBS, CATV, DVD and HDTV. The ongoing

release of Dolby Stereo Digital theatrical films now underway will

provide an immediate source of Dolby Digital (AC-3) encoded

video software.

Manufactured under license from Dolby Laboratories Licensing

Corporation. “Dolby”, “AC-3”, “Pro Logic”, and the double-D symbol

are trademarks of Dolby Laboratories Licensing Corporation.

The following original functions make the surround-sound effect

of Dolby Digital (AC-3) become the most suitable for your audio

system and the listening conditions.

● Dynamic range (sound scale) of source can be changed so

that it will be suitable for the listening conditions.

● Output of low bass from any channel can be assigned to

either the MAIN SPEAKERS terminals or SUBWOOFER

terminals to maximize system performance.

● Output of LFE can be assigned to either the MAIN

SPEAKERS terminals or SUBWOOFER terminals to

maximize system performance.

Dolby Surround + DSP (CINEMA DSP)

Dolby Surround sound system shows its full ability in a large

movie theater, because movie sounds are originally designed to be

reproduced in a large movie theater using many speakers. It is

difficult to create a sound environment similar to that of a movie

theater in your listening room, because the room size, materials of

inside walls, the number of speakers, etc. of your listening room is

much different from those of a movie theater.

Yamaha DSP technology made it possible to present you with

nearly the same sound experience as that of a large movie theater

in your listening room by compensating for lack of presence and

dynamics in your listening room with its original digital sound fields

combined with Dolby Surround sound field.

The YAMAHA “CINEMA DSP” logo indicates those programs

are created by the combination of Dolby Surround and YAMAHA

DSP technology.

CINEMA DSP

7ch

Dolby Pro Logic + 2 Digital Sound Fields

Digital sound fields are created on the presence side and the

rear surround side of the Dolby Pro Logic Surround-decoded

sound field respectively. They create a wide acoustic environment

and emphasize surround-effect in the room, letting you feel much

presence as if you are watching a movie in a popular Dolby Stereo

theater.

This combination is available when the sound field program No.

2, No. 3 or No. 4 is selected, and the input signal of source is

analog, PCM audio or encoded with the Dolby Digital (AC-3) in 2-

channels.

Dolby Digital (AC-3) + 3 Digital Sound Fields

Digital sound fields are created on the presence side and the

independent left and right surround sides of the Dolby Digital (AC-

3)-decoded sound field respectively. They create a wide acoustic

environment and much surround effect in the room without losing

high channel separation. With wide dynamic range of Dolby Digital

(AC-3) sound, this sound field combination lets you feel as if you

are watching a movie in the newest Dolby Stereo Digital theater.

This will be the most ideal home theater sound at the present time.

This combination is available when the sound field program No.

2, No. 3 or No. 4 is selected, and the input signal of source is

encoded with the Dolby Digital (AC-3) (except in 2-channels).

English

Video superimpose

If you connect your video cassette recorder, LD player, video

monitor, etc. to this unit, you can take advantage of this unit’s

capability to display program titles and information for various

setting changes and adjustments on your video monitor’s screen.

This information will be superimposed over the video image.

If there is no video source connected or it is turned off, the

information will be displayed over a blue colored background.

NOTE: The program titles and other information are also displayed

on the display panel of this unit.

TEST DSP

EFFECT LEVEL

FRONT 0dB

SPEAKERS

DSP

Setting Up Your Speaker System

This unit has been designed to provide the best sound field

quality with a full seven-speaker system setup, using two extra

pairs of effect speakers to generate the sound field plus one center

speaker for dialog. We therefore recommend that you use a seven-

speaker setup. A four-speaker system using only one pair of effect

speakers for the sound field will still provide impressive ambience

and effects, however, and may be a good way to begin with this

unit. You can always upgrade to the full seven speaker system

later. In the 4 or 5 speaker system, the Digital Sound Field

Processing is still performed, but the main speakers are used for

both the main channels and the front effect channels.

Use of the Center Dialog Speaker Is Recommended

When playing back a source with the DSP programs No. 1

through No. 4, or when the Dolby Digital (AC-3) is decoded with

any DSP program used, if the source contains center-channel

signals, dialog, vocals etc. are output from the center channel.

Therefore, if you want to maximize the performance of your

Audio/Video home theater system, it is recommended that you use

a center channel speaker.

If for some reason it is not practical to use a center speaker, it

is possible to enjoy movie viewing without it. Best results, however,

are obtained with the full system.

Use of a Subwoofer Expands Your Sound Field

It is also possible to further expand your system with the

addition of a subwoofer and amplifier. The use of a subwoofer is

effective not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency effect)

sound with high fidelity when playing back a source with the Dolby

Digital (AC-3) decoded. You may wish to choose the convenience

of a Yamaha Active Servo Processing Subwoofer System, which

has its own built-in power amplifier.

SPEAKER SETUP

English

4 Speaker System

Simplest system.

You can enjoy widely diffused sound

by only adding two additional speaker

units at the rear.

FRONT MIX switch—Set to ON.

(See page 20.)

CENTER SPEAKER—Set to PHNTM.

(See page 30.)

5 Speaker System

Good for Audio/Video sources.

By the use of center speaker, center

sounds (dialog, vocals etc.) are

precisely localized.

FRONT MIX switch—Set to ON.

(See page 20.)

CENTER SPEAKER—Set to NRML

or WIDE. (See page 30.)

6 Speaker System

Good for sound fields from 2-

channel stereo sources.

When a normal stereo source is

played back with the sound field

programs No. 5 through No. 10, a

sound effect matching that of a 7-

speaker system can be obtained. The

addition of front left and right effect

speakers produces a more effective

sound field.

FRONT MIX switch—Set to OFF.

(See page 20.)

CENTER SPEAKER—Set to PHNTM.

(See page 30.)

7 Speaker System

This is the recommended speaker

system, providing the best sound

effects.

When a normal stereo source is

played back with the sound field

programs No. 5 through No. 10, using

both sets of effect speakers (front and

rear), reproduces the most effective

sound field. When using the sound

field programs No. 1 through No. 4 or

when using any program with the

Dolby Digital (AC-3) decoded, the

center speaker provides precise center

localization.

FRONT MIX switch—Set to OFF.

(See page 20.)

CENTER SPEAKER—Set to NRML

or WIDE. (See page 30.)

Four Possible Types of Speaker System Configurations Recommended

Speakers and Speaker Placement

Your full seven-speaker system will require three speaker pairs:

the MAIN SPEAKERS (your normal stereo speakers), the FRONT

EFFECT SPEAKERS and the REAR SPEAKERS, plus the

CENTER SPEAKER. You may also be using a subwoofer.

The MAIN SPEAKERS should be high performance models

and have enough power handling capacity to accept the maximum

output of your audio system.

Other speakers do not have to be equal to the MAIN

SPEAKERS. For precise sound localization, however, it is ideal to

use high performance models that can reproduce sounds in full

range for the CENTER SPEAKER and the FRONT EFFECT and

REAR SPEAKERS.

Place the MAIN SPEAKERS in the normal position.

Place the FRONT EFFECT SPEAKERS further apart than the

MAIN SPEAKERS, on either side of and a few feet behind and

above the MAIN SPEAKER pair.

Place the REAR SPEAKERS behind your listening position.

They should be nearly six feet up from the floor.

Place the CENTER SPEAKER precisely between the two MAIN

SPEAKERS. (To avoid interference, keep the speaker above or

below the television monitor, or use a magnetically shielded

speaker.)

If using a SUBWOOFER, such as a Yamaha Active Servo

Subwoofer System, the position of the speaker is not so critical

because low bass tones are not highly directional.

Main speaker

Front effect speaker

Center speaker

Rear speaker

Subwoofer

English

FRONT PANEL

CONTROLS & THEIR FUNCTIONS

POWER

VCR 2 DVD

LDVCR 1

VIDEO AUX

TAPE (MD) TV/DBS

TUNER

PHONO

VOLUME

–dB

SPEAKERSPHONES

OFF

BASS

EXTENSION

TONE

BYPASS

BASS TREBLE BALANCE

VIDEO AUX

S VIDEO VIDEO L AUDIO R

DELAY

SWFR

SET

EFFECTPROGRAM

NATURAL SOUND AV AMPLIFIER

DSP–A1092

CINEMA DSP

7ch

VCR 2

VIDEO AUX

REC OUT

VCR 1

TV/DBS

PHONO

TUNER

DVD/LD

SOURCE

TAPE (MD)

1 456

JIHGF

EDCBA0987

(Europe Model)

* For control keys on the remote control unit, see pages 50 to 52.

1 POWER Switch

Turns this unit on and off.

* When you press this switch to turn the power on, you will hear

a click and a sound of the built-in fan rotating for a moment.

2 Standby Indicator

While the power of this unit is on, pressing the (SYSTEM

POWER) OFF key on the remote control unit switches this unit

to the standby mode. In this mode, the standby indicator is

illuminated.

3 Remote Control Sensor

Signals from the remote control unit are received here.

4 Display Panel

See page 16.

5 Input Selector Buttons

Selects an input source that you want to listen to (and watch).

6 Master VOLUME Control

Simultaneously controls volume level at all outputs: front effect,

main, rear effect, center, and subwoofer. (This does not affect

REC OUT level.)

* When the volume is decreased by pressing the MUTE key on

the remote control unit, the indicator on the master VOLUME

control flashes on and off.

7 PHONES Jack

When you listen with headphones, connect the headphones to

the PHONES jack. You can listen to the sound to be output

from the main speakers through headphones.

When listening with headphones privately, set both the

SPEAKERS A and B switches to the OFF position and switch

off the digital sound field processor (so that no DSP program

name is illuminated on the display panel) by pressing the

EFFECT switch.

8 SPEAKERS switches

Set the switch A or B (or both A and B) for the main speakers

(connected to this unit) you will use to the ON position. Set the

switch for the main speakers you will not use to the OFF

position. Selected main speakers are shown by the lighting of

“SPEAKERS A” and/or “SPEAKERS B” on the display panel.

9 BASS EXTENSION Switch

When pressed inward (ON), boosts bass frequency response

at the main left and right channels while maintaining overall

tonal balance. If you do not have a subwoofer, the use of this

switch will be effective to reinforce the bass frequencies.

0 TONE BYPASS switch

When this switch is pressed inward (ON), the input signal does

not pass through the tone (BASS and TREBLE) control circuitry

so that it is unaffected by the tone control circuitry. Use this

switch to obtain pure sound and to check the tone control

setting. Press this switch to release it outward (OFF) to use the

tone control circuitry.

A BASS and TREBLE Controls

Adjust low and high frequency response respectively for the

main channels only.

B BALANCE Control

Adjusts the left and right output volume to the Main Speakers to

compensate for sound imbalance caused by speaker positions

or listening room conditions.

C REC OUT Selector

Selects the source to be recorded to a tape deck or

VCR independently of the setting of the input selector buttons.

However, when set to the SOURCE position, the setting of the

input selector buttons decides the source to be recorded to a

tape deck or VCR.

English

D PROGRAM Selector

Sequentially selects the digital sound field processing programs

in the + or – direction.

E SET MENU Switch

Whenever pressed, selects functions in the SET MENU mode.

F DELAY/C/R/F/SWFR Switch

Whenever pressed, selects the item of changing delay time,

center speaker output level, rear speaker output level, front

effect speaker output level and subwoofer output level in turn.

* Depending on a mode of this unit, the number of selections is

reduced. For example, when the built-in digital sound field

processor (including the Dolby Pro Logic Decoder or the

Dolby Digital (AC-3) Decoder) is off, only the item for

changing subwoofer output level can be selected.

G –/+ Button

Adjusts the level of item selected by pressing the

DELAY/C/R/F/SWFR switch. Moreover, performs setting

changes and adjustments for functions selected by pressing

the SET MENU switch.

H EFFECT Switch

Normally ON, this switch can be turned OFF to disable output

from the center and effect speakers so that the sound becomes

normal 2-channels.

* Even if this switch is off, when the Dolby Digital (AC-3) is

decoded, signals at all channels are distributed to the main

channels and output from the main speakers.

I Auxiliary Input Jacks (VIDEO AUX)

Connect an auxiliary video or audio unit such as a camcorder

to these jacks. If the connected video unit has a S video output

terminal, connect it to the S VIDEO jack to obtain a high

resolution picture. The unit connected to these jacks can be

selected by the corresponding input selector button and REC

OUT selector.

J Control Door

See page 4 for how to open and close the control door.

1 Input Source Display

Shows the currently selected input source.

2 Multi-informatiom Display

Shows the currently selected DSP program, or information for

several adjustments or setting changes made on this unit.

3 SPEAKERS A/B Indicators

The indicator A or B which corresponds to the currently

selected main speakers lights up. If both main speakers A or B

are selected, both indicators light up.

4 Digital Audio Input Signal Indicators

When digital audio signals not encoded with the Dolby Digital

(AC-3) are input to this unit, “PCM DIGITAL” lights up.

When digital audio signals encoded with the Dolby Digital

(AC-3) are input to this unit, “ DIGITAL” lights up.

5 DIGITAL, DSP and PRO LOGIC indicators

“ DIGITAL” lights up when the built-in Dolby Digital (AC-3)

Decoder is on and the signals of selected source encoded with

the Dolby Digital (AC-3) is not in 2-channels. “DSP” lights up

when the built-in digital sound field processor is on, and “

PRO LOGIC” lights up when the built-in Dolby Pro Logic

Surround Decoder is on. Depending on the selected DSP

program, both “ DIGITAL” and “DSP”, or both “DSP” and “

PRO LOGIC” will light up.

6 SLEEP Indicator

Lights up while the built-in SLEEP timer is functioning.

DISPLAY PANEL

DIGITAL

ENHANCED

SPEAKERS

PCM

DIGITAL

SLEEP

mS dB

DSP

PRO LOGIC

3 4 5 6

1 2

English

PHONO

VIDEO

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

DVD/LD

TV/DBS

CENTER

C OR D

C D

SEE INSTRUCTION MANUAL FOR CORRECT

SETTING.

CENTER

CAUTION

VCR 1

OUT

VCR 2

OUT

MONITOR

OUT

MAIN CH SUB

WOOFER

FRONT

EFFECT

REAR

PRE

OUT

MAIN

S VIDEO

TUNER

TAPE

AUDIO SIGNAL

GND

AUDIO SIGNAL VIDEO SIGNAL OUTPUT SPEAKERS

COUPLER OUTPUT

5ch 7ch

ON OFF

PAL NTSC

MONITOR

OUT

FRONT

MIX

—

I0dB 0dB

MAIN

LEVEL

REAR

FRONT

EFFECT

MAIN

SWITCHED

AC OUTLETS

IMPEDANCE SELECTOR

VOLTAGE SELECTOR

I00W

MAX.

TOTAL

PCM/

DIGITAL IN

REC

OUT

TAPE(MD)

DVD/LD

OPTICAL

COAXIAL

OPTICAL

(AC-3 DIGITAL IN)

TV/DBS

COAXIAL

CENTER C OR D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 4

Ω

MIN./ SPEAKER

A B

: 8

Ω

MIN./ SPEAKER

FRONT EFFECT

: 6

Ω

MIN./ SPEAKER

CENTER C OR D: 8

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 8

Ω

MIN./ SPEAKER

A B

: 6

Ω

MIN./ SPEAKER

FRONT EFFECT

: 8

Ω

MIN./ SPEAKER

0ABCDEFIJ KHG

12 3 4 56 7 89

REAR PANEL PARTS AND THEIR FUNCTIONS

Before you start making connections make sure all related electronic components are turned OFF.

CONNECTIONS

(General Model)

To AC outlet

1 PCM/ DIGITAL IN (COAXIAL and OPTICAL) jacks

Can be connected with audio/video units that have a coaxial or

optical digital output jack. Connect a unit that is connected to

the DVD/LD AUDIO/VIDEO SIGNAL connection jacks to the

DVD/LD COAXIAL or OPTICAL jack.

Connect a unit that is connected to the TV/DBS AUDIO/VIDEO

SIGNAL connection jacks to the TV/DBS COAXIAL or

OPTICAL jack.

* If, for example, your LD player has an AC-3 RF output jack

and no digital output jack for AC-3 discrete audio signals,

connect the AC-3 RF output jack to the DVD/LD COAXIAL or

OPTICAL jack of this unit by way of an RF demodulator

(separate purchase).

2 AUDIO SIGNAL Connection Jacks (for Audio Source

Equipment)

Connect the inputs and/or outputs of your audio equipment.

3 AUDIO/VIDEO SIGNAL Connection Jacks (for Video Source

Equipment)

Connect the audio and video inputs and/or outputs of your

video equipment. In place of the VIDEO jacks, the S VIDEO

jacks can be used for higher resolution and improved picture

quality if your VCR, monitor, etc. are equipped with S-VIDEO

connectors.

4 CENTER OUTPUT Jacks

Center-channel line outputs. Can be connected to input jack(s)

of one or two external power amplifier(s) to drive the center

speaker(s).

5 CENTER SPEAKERS Terminals

When using the built-in center-channel amplifier, connect one

or two center speakers here.

6 Center Speaker Switch

Set to “C + D” when using two center speakers, or to “C OR D”

when using only one center speaker.

7 FRONT EFFECT SPEAKERS Terminals

When using the built-in front effect-channel amplifier, connect

the front effect speakers here.

8 REAR SPEAKERS Terminals

When using the built-in rear-channel amplifier, connect the rear

speakers here.

9 VOLTAGE SELECTOR (General Model only)

Be sure to set to the line voltage in your area before applying

power. Consult your dealer if unsure of the correct setting.

0 GND Terminal

Connects the ground wire of the turntable to produce minimum

hum. In some cases, however, better results may be obtained

with the ground wire disconnected.

A Video NTSC/PAL Switch (General Model only)

Set this switch to the position corresponding to the standard

that your video equipment employs.

B FRONT MIX Switch

Set to “OFF (7ch)” when setting up a full 7 or 6 speaker

system, or to “ON (5ch)” when setting up a 5 or 4 speaker

system.

C MAIN LEVEL Switch

Normally set to “0 dB”. If desired, you can decrease the main-

channel output level at the MAIN SPEAKERS terminals by 10

dB by setting this switch to “–10 dB”.

English

D PRE OUT Jacks

Main-channel line output. Connected with jumper bars to MAIN

IN jacks when the built-in amplifier is used. Connected to input

jacks of external stereo power amplifier (MAIN IN or TAPE

PLAY jacks of integrated amplifier or receiver) when using

external amplification.

E MAIN IN Jacks

Line input to built-in main-channel amplifier. Connected with

jumper bars to PRE OUT jacks when the built-in amplifier is

used. Not connected when using an external power amplifier.

F SUBWOOFER Jacks

When using one subwoofer, connect its amplifier input to either

of these jacks. When using two subwoofers, connect their

amplifiers to these jacks respectively.

Frequencies below 90 Hz distributed from the main, center

and/or rear channels are output to these jacks.

Signals of LFE (low frequency effect) generated when the

Dolby Digital (AC-3) is decoded are also output if they are

assigned to these jacks.

G FRONT EFFECT OUTPUT Jacks

Front-channel line output. Can be connected to input jacks of

an external stereo power amplifier driving the front effect

speakers.

H REAR OUTPUT Jacks

Rear-channel line output. Can be connected to input jacks of

an external stereo power amplifier driving the rear speakers.

I MAIN SPEAKERS Terminals

This unit is equipped with 2 sets of MAIN SPEAKERS terminals

to allow you to connect 2 main speaker systems to this unit.

When using this unit’s built-in main-channel amplifier, connect

the main speakers here. The jumper bars must be plugged in to

connect the MAIN IN jacks to the PRE OUT jacks.

J IMPEDANCE SELECTOR Switch

Select the position whose requirements your speaker system

meets.

K SWITCHED AC OUTLET(S)

You may plug other audio/video units into these sockets as long

as their combined power consumption does not exceed the

specified value shown. “Switched” means that these

components are turned on and off by this unit’s power switch.

REAR PANEL SWITCH AND CONTROL

SETTINGS

There are several switches and controls on the rear panel that

you’ll have to check before operating your system, and it’s a good

idea to do it before you connect cables. Locate the MAIN LEVEL

slide switch (C) and FRONT MIX slide switch (B). Make sure the

MAIN LEVEL switch is set to “0 dB” and the FRONT MIX switch is

set to “OFF” for 7 or 6 speaker driving.

In a 5 or 4 speaker system, set the FRONT MIX switch to “ON”.

Next, set the NTSC/PAL switch (A) to the position

corresponding to the standard which your video equipment

employs. (General Model only)

For the setting of IMPEDANCE SELECTOR switch (J), see

page 29.

For the setting of the center speaker switch (6), see page 27.

GENERAL INSTRUCTIONS FOR

CONNECTIONS

Make sure that you have the left (L) and right (R) channels

correctly connected. That means that jacks marked “L” on this unit

must be connected to jacks marked “L” on other units. Likewise

with the “R” jacks. This is easy if you remember to always use the

red plug for the “R” jacks and the white plug for the “L” jacks.

For connections with audio/video source equipment, use RCA

type pin plug cables with the exception described later.

With speaker connections you must also be sure that the

polarity is correct. For each amplifier and each channel, connect

the plus (+) terminal of the amplifier to the plus terminal of the

speaker, and connect the minus (–) terminal of the amplifier to the

minus terminal of the speaker. To keep track of polarity, use a

speaker cable that has one of the two wires marked by a stripe or

a different color.

English

PHONO

VIDEO

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

MONITOR

OUT

S VIDEO

TUNER

TAPE

AUDIO SIGNAL

GND

AUDIO SIGNAL VIDEO SIGNAL

5ch 7ch

ON OFF

PAL NTSC

MONITOR

OUT

FRONT

MIX

—

I0dB 0dB

MAIN

LEVEL

PCM/

DIGITAL IN

REC

OUT

TAPE(MD)

DVD/LD

OPTICAL

COAXIAL

OPTICAL

TV/DBS

COAXIAL

OUTPUT

GND

OUTPUT

LINE OUT

LINE IN

VIDEO IN

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

VIDEO IN

AUDIO IN

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO OUT

VIDEO OUT

CONNECTING AUDIO/VIDEO SOURCE EQUIPMENT TO THIS UNIT

BASIC CONNECTIONS

* If you have YAMAHA audio/video unit numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure to

connect the output (or input) terminals of each unit to the same-numbered terminals of this unit.

* For shaded parts, see pages 22 to 24.

Turntable

CD player

Tuner

Tape deck (MD recorder)

LD (DVD) player

TV/Satellite tuner

Video cassette

recorder 1

Video cassette

recorder 2

Monitor TV

CONNECTING TO DIGITAL (OPTICAL AND COAXIAL)

JACKS

If your LD (DVD) player, TV/satellite tuner, etc. are equipped

with coaxial or optical digital audio signal output jacks, they can be

connected to this unit’s COAXIAL and/or OPTICAL digital signal

input jacks.

To make a connection between optical digital audio signal

jacks, remove the cover from each jack, and then connect them by

using a commercially available optical fiber cable that conforms to

EIAJ standards. Other cables might not function correctly.

Even if you connect an audio/video unit to the OPTICAL (or

COAXIAL) jack of this unit, you must keep the unit connected with

the same named analog audio signal jacks of this unit, because

digital signal cannot be recorded by a tape deck or VCR

connected to this unit. You can switch the selection of input signals

between “digital” and “analog” easily. (See page 39 for details.)

NOTE: When connecting an audio/video unit to both of the digital

and analog jacks of this unit, make sure to connect to both jacks of

the same name.

NOTE: Be sure to attach the covers when the OPTICAL jacks are

not being used, in order to protect the jacks from dust.

NOTE: All digital audio signal input jacks are applicable to the

sampling frequency of 32 kHz, 44.1 kHz and 48 kHz.

PHONO

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

TUNER

TAPE

AUDIO SIGNAL

GND

AUDIO SIGNAL

PAL NTSC

MONITOR

OUT

PCM/

DIGITAL IN

REC

OUT

TAPE(MD)

DVD/LD

OPTICAL

COAXIAL

OPTICAL

TV/DBS

COAXIAL

DIGITAL OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

ANALOG OUT

LD (DVD) player

TV/Satellite tuner

English

Notes on connecting with an LD player equipped

with an AC-3 RF output

If your LD player has AC-3 RF signal output jack and no digital

signal output jack for AC-3 discrete audio signals, connect the AC-

3 RF signal output jack to this unit’s OPTICAL (or COAXIAL) digital

signal input jack by using an RF demodulator (separate purchase).

First, connect the AC-3 RF signal output jack of the LD player to

the AC-3 RF signal input jack of the RF demodulator. Next,

connect the optical (or coaxial) digital signal output jack of the RF

demodulator to the OPTICAL (or COAXIAL) digital signal input jack

of this unit.

This connection is necessary for inputting audio signals encoded

with the Dolby Digital (AC-3) on the LD player to this unit.

It is also necessary to connect the LD player to this unit’s

analog audio signal input jacks regardless of the AC-3 RF signal

connection, for playing back an LD source with the Dolby Pro Logic

Surround decoded or in normal stereo (or monaural).

If desired, you can also connect the digital signal output jack

(for 2-channel audio signals) of the LD player to this unit. If you will

do so, connect it to the COAXIAL digital signal input jack of this

unit, and connect the RF demodulator to the OPTICAL digital

signal input jack of this unit.

By this connection, if the input mode of the DVD/LD source is in

“AUTO”, you can enjoy listening to sounds decoded with the Dolby

Digital (AC-3) when you play a disc encoded with the Dolby Digital

(AC-3) though signals are input to both OPTICAL and COAXIAL

digital signal input jacks of this unit simultaneously (because

signals input to the OPTICAL jack take priority of signals input to

the COAXIAL jack).

See page 39 for details about switching the input mode.

NOTES

●

If, for example, you play a CD on the LD player (which can play

a CD also), there is no input to the OPTICAL jack, so the

signals input to the COAXIAL jack take priority. In this case,

switch off the RF demodulator to listen to CD sound surely.

However, if your RF demodulator is the Yamaha model APD-1,

you do not have to switch it off.

●

When you want to play a source encoded with the Dolby Digital

(AC-3) without decoding the Dolby Digital (AC-3), you must

switch off the power to the RF demodulator.

PHONO

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

TUNER

TAPE

AUDIO SIGNAL

GND

AUDIO SIGNAL

MONITOR

OUT

PCM/

DIGITAL IN

REC

OUT

TAPE(MD)

DVD/LD

OPTICAL

COAXIAL

OPTICAL

TV/DBS

COAXIAL

COAXIAL DIGITAL OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

ANALOG OUT

AC-3

RF OUT

AC-3

RF IN

RF demodulator

(YAMAHA APD-1 etc.)

LD player

CONNECTING TO S VIDEO JACKS

If your video cassette recorder, LD player, etc. and your monitor

are equipped with “S” (high-resolution) video terminals, connect

them to this unit’s S VIDEO jacks, and connect this unit’s

S VIDEO MONITOR OUT jack to the “S” video input of your

monitor. Otherwise, connect the composite video jacks from your

video cassette recorder, LD player, etc. to the VIDEO jacks of this

unit, and connect this unit’s VIDEO MONITOR OUT jack to the

composite video input of your monitor.

NOTE: If video signals are sent to both S VIDEO input and VIDEO

input jacks, the signals will be sent to their respective output jacks

independently.

NOTE: If your unit is the General Model, be sure the NTSC/PAL

switch has been correctly set to the standard that your video

equipment employs. Other models have no switch and use the PAL

standard.

Notes about the Video superimpose

● If you watch a video source that is connected to both S VIDEO

and VIDEO input jacks of this unit, signals of screen display

information are output from only the S VIDEO MONITOR OUT

jack.

● When no video signal is input to either S VIDEO or VIDEO input

jacks of this unit, signals of screen display information are

output from both S VIDEO MONITOR OUT and VIDEO

MONITOR OUT jacks with a color background.

* For the General Model, if the NTSC/PAL switch on the rear

panel is set to “PAL”, nothing will be output from either S

VIDEO MONITOR OUT or VIDEO MONITOR OUT jack in this

case.

VIDEO

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

DVD/LD

TV/DBS

VCR 1

OUT

VCR 2

OUT

MONITOR

OUT

S VIDEO

AUDIO SIGNAL VIDEO SIGNAL

PAL NTSC

MONITOR

OUT

VIDEO IN

S-VIDEO IN

VIDEO

OUT

S-VIDEO

OUT

VIDEO IN

S-VIDEO IN

S-VIDEO

OUT

VIDEO

OUT

VIDEO

OUT

S-VIDEO

OUT

VIDEO IN

S-VIDEO IN

VIDEO OUT

S-VIDEO OUT

LD (DVD) player

TV/Satellite tunerVideo cassette recorder 1

Video cassette recorder 2

Monitor TV

English

For connecting with a monitor TV that uses a 21 pin

connector for input (for Europe and U.K. models)

Make a connection as figured below with a commercially

available scart-plug connector cable.

CONNECTING SPEAKER SYSTEMS

Connect the SPEAKERS terminals to your speakers with wire

of the proper gauge, cut as short as possible. If the connections

are faulty, no sound will be heard from the speakers. Make sure

that the polarity of the speaker wires is correct, that is, + and –

markings are observed. If these wires are reversed, the sound will

be unnatural and will lack bass. Do not let the bare speaker wires

touch each other or any other metal part as this could damage this

unit and/or speakers.

NOTE: Use speakers with the specified impedance shown on the

rear of this unit.

Red: positive (+)

Black: negative (–)

➀ Unscrew the knob.

➁ Insert the bare wire.

[Remove approx. 5mm (1/4”)

insulation from the speaker

wires.]

➂ Tighten the knob and

secure the wire.

NOTE: Banana Plug connections are also possible (Australia and

General models only). Simply insert the Banana Plug connector

into the corresponding terminal.

VCR 2

OUT

VCR 2

OUT

MONITOR

OUT

PAL NTSC

MONITOR

OUT

VIDEO

AUDIO L

AUDIO R

Monitor TV

No connection

Scart-plug

connector

cable

CONNECTING THE MAIN SPEAKERS TO THIS UNIT

One or two sets of MAIN speakers can be connected to this

unit.

If you use two sets of MAIN speakers, connect one set to the

MAIN SPEAKERS A terminals, and connect another set to the B

terminals. If you use only one set of MAIN speakers, connect them

to either the MAIN SPEAKERS A or B terminals. Make sure that

the jumper bars between the PRE OUT and MAIN IN jacks on the

rear panel are in place.

It is also possible to use an external power amplifier if more

power is desired. In this case, remove the jumper bars and

connect the PRE OUT jacks to the INPUT jacks of a stereo power

amplifier with a stereo pin cable—making sure to connect the left

and right channels correctly. Connect the MAIN speakers to the

speaker output terminals of the power amplifier.

Set the SPEAKERS switch A or B (or both A and B) on the

front panel corresponding to the main speakers you will use to the

ON position. Set the switch for the main speakers you will not use

to the OFF position. Selected main speakers are shown by the

lighting of “SPEAKERS A” and/or “SPEAKERS B” on the display

panel.

PRE OUT

INPUT

Main speaker A Main speaker A

Main speaker B Main speaker B

Power amplifier

This unit

English

CONNECTING THE FRONT EFFECT SPEAKERS,

REAR SPEAKERS AND THE CENTER SPEAKER(S)

TO THIS UNIT

Connect the FRONT effect speakers to the FRONT EFFECT

SPEAKERS terminals of this unit.

If the FRONT effect speakers are not used, the FRONT MIX

switch should be set to “ON”.

Connect the REAR speakers to the REAR SPEAKERS

terminals of this unit.

Connect the CENTER speaker to the CENTER SPEAKERS

terminals. If you will be using one CENTER speaker, connect it to

either the C or D terminals and set the CENTER speaker switch so

that it is released outward (“C OR D” position). If using two

CENTER speakers, connect them to the C and D terminals, and

press the switch inward (“C+D” position). If, however, you will not

be using a CENTER speaker, be sure to set the CENTER

SPEAKER mode to “PHNTM” (phantom). (See page 30.)

NOTE: The speaker connections above are fine for most

applications. If for some reason, however, you wish to use an

external power amp for any or all of the front effect, rear and center

channels, connect the line level output jack(s) for each channel to

the INPUT jacks of the external amp and connect the

corresponding speaker pair to the speaker terminals of the

external amp.

Center speaker

Front effect

speaker

Front effect

speaker

Rear speaker

This unit

ADDING A SUBWOOFER

You may wish to add a subwoofer to reinforce the bass

frequencies.

This unit provides line-level subwoofer outputs. If you use one

subwoofer, connect either of the SUBWOOFER jacks to the INPUT

jack of the subwoofer amplifier, and connect the speaker terminals

of the subwoofer amplifier to the subwoofer.

If you wish to obtain more presence in your listening room, the

use of two subwoofers is recommended. To connect two

subwoofers to this unit, connect one SUBWOOFER jack to the

INPUT jack of the amplifier driving a subwoofer, and the other

SUBWOOFER jack to the INPUT jack of the amplifier driving the

other subwoofer, and then connect each subwoofer to the

corresponding amplifier.

With some subwoofers, including the Yamaha Active Servo

Processing Subwoofer System, the amplifier and subwoofer are in

the same unit.

Subwoofer system

Subwoofer systemSubwoofer system

MAIN CH SUB

WOOFER

FRONT

EFFECT

REAR

PRE

OUT

MAIN

COUPLER OUTPUT

MAIN CH SUB

WOOFER

FRONT

EFFECT

REAR

PRE

OUT

MAIN

COUPLER OUTPUT

English

Switching the IMPEDANCE SELECTOR switch on the

rear panel

Select the position whose requirements your speaker system

meets. Be sure to switch this only when the power of this unit is

turned off.

WARNING

Never switch the setting of this switch when the power of

this unit is on, otherwise this unit will break down.

(Upper position)

Center:If you use one center speaker, the impedance of the

speaker must be 4Ω or higher.

If you use two center speakers, the impedance of each

speaker must be 4Ω or higher.

Rear: The impedance of each speaker must be 4Ω or higher.

Main: If you use one pair of main speakers, the impedance of

each speaker must be 4Ω or higher.

If you use two pairs of main speakers, the impedance of

each speaker must be 8Ω or higher.

Front effect:

The impedance of each speaker must be 6Ω or higher.

(Lower position)

Center:If you use one center speaker, the impedance of the

speaker must be 8Ω or higher.

If you use two center speakers, the impedance of each

speaker must be 4Ω or higher.

Rear: The impedance of each speaker must be 8Ω or higher.

Main: If you use one pair of main speakers, the impedance of

each speaker must be 8Ω or higher.

If you use two pairs of main speakers, the impedance of

each speaker must be 16Ω or higher.

Front effect:

The impedance of each speaker must be 8Ω or higher.

(Europe model)

IMPEDANCE SELECTOR

CENTER C OR D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 4

Ω

MIN./ SPEAKER

A B

: 8

Ω

MIN./ SPEAKER

FRONT EFFECT

: 6

Ω

MIN./ SPEAKER

CENTER C OR D: 8

Ω

MIN./ SPEAKER

SET SPEAKER MODE

D: 4

Ω

MIN./ SPEAKER

SET SPEAKER MODE

REAR

Ω

MIN./ SPEAKER

MAIN

B: 8

Ω

MIN./ SPEAKER

A B

: 6

Ω

MIN./ SPEAKER

FRONT EFFECT

: 8

Ω

MIN./ SPEAKER

SELECTING THE OUTPUT MODES SUITABLE FOR YOUR SPEAKER SYSTEM

This unit provides you the following four functions to determine the method of distributing output signals to speakers suitable for your audio

system. When speaker connections are all completed, select a proper position on each function to make the best use of your speaker

system.

4. CENTER SPEAKER

5. REAR SPEAKER

6. MAIN SPEAKER

7. LFE/BASS OUT

4. CENTER SPEAKER

Choices: NRML/WIDE/PHNTM

Preset position: NRML

NRML (Normal):

Select this position when you use a center speaker that is

smaller than the main speakers. In this position, low bass

signals (below 90 Hz) at the center channel are output

from the main speakers (or the SUBWOOFER jacks if the

SMALL position is selected on “6. MAIN SPEAKER” and

the SWFR position is selected on “7. LFE/BASS OUT”).

WIDE: Select this position when your center speaker is

approximately the same size as the main speakers.

PHNTM (Phantom):

Select this position when you do not have a center

speaker. The center channel sound will be output from the

left and right main speakers.

5. REAR SPEAKER

Choices: SMALL/LARGE

Preset position: SMALL

SMALL:

Select this position if your rear speakers do not have a

high ability for bass reproduction.

In this position, low bass signals (below 90 Hz) at the rear

channels are output from the SUBWOOFER jacks (or the

main speakers if the MAIN position is selected on “7.

LFE/BASS OUT”).

LARGE:

Select this position if your rear speakers have a high ability

for bass reproduction, or a subwoofer is connected to the

rear speaker in parallel.

In this position, full range signals are output from the rear

speakers.

DESCRIPTION OF EACH FUNCTION

English

6. MAIN SPEAKER

Choices: SMALL/LARGE

Preset position: LARGE

SMALL:

Select this position if your main speakers do not have a

high ability for bass reproduction. However, if your system

does not include a subwoofer, do not select this position.

In this position, low bass signals (below 90 Hz) at the main

channels are output from the SUBWOOFER jacks (if the

SWFR or BOTH position is selected on “7. LFE/BASS

OUT”).

LARGE:

Select this position if your main speakers have a high

ability for bass reproduction.

In this position, full range signals present at the main

channels are output from the main speakers.

7. LFE/BASS OUT

Choices: MAIN/SWFR/BOTH

Preset position: SWFR

MAIN: Select this position if your system does not include a

subwoofer.

In this position, full range signals present at the main

channels, signals from the LFE channel and other low

bass signals that are selected on “4. CENTER SPEAKER”

to “6. MAIN SPEAKER” to be distributed from other

channels are output from the main speakers.

SWFR/BOTH:

Select either the SWFR or BOTH position if your system

includes a subwoofer.

In either position, signals at LFE channel and other low

bass signals that are selected on “4. CENTER SPEAKER”

to “6. MAIN SPEAKER” to be distributed from other

channels are output from the SUBWOOFER jacks.

When the LARGE position is selected on “6. MAIN

SPEAKER”, in the SWFR position, no signal is distributed

from the main channels to the SUBWOOFER jacks,

however in the BOTH position, low bass signals from the

main channels are output to both of the main speakers and

the SUBWOOFER jacks.

METHOD OF CHANGING SELECTIONS

Operations should be made watching information on this unit’s

display panel or the monitor screen.

1. Turn the power of this unit on. (If you want to display

information on the monitor, turn the power of the monitor on.)

If you will use the remote control unit, set the TIME/LEVEL·SET

MENU switch to the SET MENU position on the remote control

unit.

NOTE: Be sure to use the remote control unit with the lid open.

2. Press once or more until “4. CENTER SPEAKER” appears on

the display.

3. Press “+” or “–” once or more so that the arrow points the

position you will select.

4. Press once or more until the title of another function on which

you will change the selection appears on the display.

5. Press “+” or “–” once or more so that the arrow points the

position you will select.

6. Repeat step 4 and 5 to change selections on other functions in

the same way.

Front panel

Remote control

Front panel

Remote control

POWER

TIME/LEVEL

SET MENU

SET

Front panel

Remote control

SET

Front panel

Remote control

English

This operation uses an internal test-tone generator for balancing

the levels of the main, center, rear and front effect speakers.

The adjustment of each speaker output level should be done at

your listening position with the remote control unit. Otherwise, the

result may not be satisfactory.

NOTE: Be sure to use the remote control unit with the lid open.

1. Set the TIME/LEVEL·SET MENU switch on the remote control to

the TIME/LEVEL position.

2. Depress the TEST key on the remote

control so that “TEST DOLBY SUR.” appears

on the display panel to enter test mode. A

hiss-like calibration signal should be heard

from the left main speaker, center speaker(s),

right main speaker, right rear speaker and left

rear speaker in turn (see diagram). Adjust the

master VOLUME to a normal listening level.

* The state of test-tone output is shown on the display panel and

the monitor screen. (On the monitor screen, it is shown by an

image of audio listening room.) This is convenient for adjusting

each speaker level.

3. Press the or key to select the speaker whose level you will

adjust.

* Whenever the key is pressed, the speaker selection changes

in turn as follows.

Pressing the key changes the speaker in the reverse order.

* If the CENTER SPEAKER mode is set to “PHNTM” (phantom),

“CENTER” cannot be selected. (See page 30.)

4. Adjust the level of the speaker selected in step 3 by pressing the

+ or – key so that it becomes almost as same as that of the main

speakers.

* While adjusting, the test-tone is fixed on the selected speaker.

5. Repeat step 3 and 4 to adjust the level of other speakers.

SPEAKER BALANCE ADJUSTMENT

Left main Center Right main

Right rear

LEFT CENTER RIGHT

Left rear

LEFT

SURROUND

RIGHT

SURROUND

TIME/LEVEL

SET MENU

Remote control

TEST

CENTER

R SUR.

L SUR.

Center

Right rear

Left rear

NOTE: If there is insufficient volume from the effect speakers, you

may decrease the main speaker volume level by setting the MAIN

LEVEL switch on the rear panel to “–10 dB”, and adjust each speaker

level again. Volume controls on external power amplifiers may also

be adjusted if necessary to achieve proper balance.

NOTE: If not using a center speaker, be sure to set the “4. CENTER

SPEAKER” in the SET MENU mode to the PHNTM (phantom)

position. You will then hear the center channel test tone from the left

and right main speakers.

6. For the front effect speaker level adjustment, depress the TEST

key on the remote control again so that “TEST DSP” appears on the

display panel. A calibration signal should be heard from the main

speakers and the front effect speakers in turn (see diagram).

* If the FRONT MIX switch on the rear panel is set to “ON (5ch)”,

the front effect speaker level cannot be adjusted by this method.

7. Adjust the front effect speaker level by pressing the + or – key so

that it becomes almost as same as that of the main speakers.

* While adjusting, the test-tone is fixed on the front effect speaker.

8. When this adjustment is finished, press the TEST key once again.

NOTE: Once you have completed these adjustments, use only

VOLUME control of this unit or MASTER VOLUME keys of the

remote control unit to adjust the whole listening volume. Do not

change any other volume setting in the system.

Main Front

MAIN FRONT

Remote control

TEST

Remote control

TEST

English

The following eight types of functions maximize the performance

of your system and expand your enjoyment for audio listening and

video watching.

1. CENTER DELAY

2. DYNAMIC RANGE

3. LFE LEVEL

4. CENTER SPEAKER

5. REAR SPEAKER

6. MAIN SPEAKER

7. LFE/BASS OUT

8. INPUT MODE (TV/DBS)

METHOD OF SETTING CHANGE AND ADJUSTMENT

Operations should be made watching information on this unit’s

display panel or the monitor screen. If you want to display information

on the monitor, turn the power of the monitor on.

1. If you will use the remote control unit, set the TIME/LEVEL·SET

MENU switch to the SET MENU position on the remote control unit.

NOTE: Be sure to use the remote control unit with the lid open.

2. Select the function (title) on which you will make a change.

3. Select any desired position or edit parameters on the function.

In the same way, make a setting change or adjustment on any

other function.

ADJUSTMENTS IN THE “SET MENU” MODE

Remote control

Front panel

Remote control

TIME/LEVEL

SET MENU

SET

DESCRIPTIONS OF THE FUNCTIONS

1. CENTER DELAY (Adjusting the delay of center

sounds (dialog etc.))

Control range: 0 ms to 5 ms (in 1 ms step)

Preset value: 0 ms

* This adjustment is effective only when the Dolby Digital (AC-3)

is decoded and the signals of selected source encoded with the

Dolby Digital (AC-3) contain center-channel signals.

Adjusts the delay between the main sounds (at the main

channels) and dialog etc. (at the center channel).

The larger the value, the later the dialog etc. is generated.

This is for making sounds from the left main, center and right

main speakers reach your listening position at the same time by

delaying the sound from the center speaker if the distance from the

center speaker to your listening position is shorter than the

distance from the left or right main speaker to your listening

position.

2. DYNAMIC RANGE (Adjusting dynamic range)

Choices: MAX/STD/MIN

Preset position: MAX

* This adjustment is effective only when the Dolby Digital (AC-3)

is decoded.

MAX: “Dynamic range” is the difference between the maximum

level and the minimum level of sounds. Sounds on a movie

originally designed for movie theaters feature very wide

dynamic range.

Dolby Digital (AC-3) technology can bring the original

sound track into a home audio format with this wide

dynamic range unchanged.

In this position, a source encoded with the Dolby Digital

(AC-3) is reproduced in the original sound track’s wide

dynamic range providing you with powerful sounds like a

movie theater.

Selecting this position will be more ideal if you can listen to

a source in a high output level in a room specially

soundproofed for audio/video enjoyment.

STD (Standard):

Powerful sounds of extremely wide dynamic range are not

always suitable for home use. Depending upon the

condition of your listening environment, it may not possible

to increase the sound output level as high as a movie

theater, however, in a level proper for listening to in your

room, the low level parts of source sound cannot be heard

as well because they will be lost among noises in your

environment.

Dolby Digital (AC-3) technology also makes it possible to

reduce an original sound track’s dynamic range for a home

audio format by “compressing” the data.

In this position, a source encoded with the Dolby Digital

(AC-3) is reproduced in the “compressed” dynamic range

of the source suitable for low level listening.

MIN: In this position, dynamic range is more reduced than in the

STD position. Selecting this position will be effective when

you must listen to a source in extremely low level.

English

3. LFE LEVEL (Adjusting the output level at the LFE

(low frequency effect) channel)

Control range: –20 dB to 0 dB (in 1 dB step)

Preset value: 0 dB

* This adjustment is effective only when the Dolby Digital (AC-3) is

decoded and the signals of selected source encoded with the

Dolby Digital (AC-3) contain LFE signals.

Adjusts the output level at the LFE (low frequency effect)

channel. If the LFE signals are mixed with signals at other

channels to output them from the same speakers, the ratio of LFE

signal level to the level of other signals are adjusted. (See page 6

for details about the LFE channel.)

4. CENTER SPEAKER 6. MAIN SPEAKER

5. REAR SPEAKER 7. LFE/BASS OUT

See pages 30 to 31 for details. (Once you have selected proper

modes, you do not have to make a setting change until any

alteration is made in your speaker system.)

8. INPUT MODE (Selecting the initial input mode of the

sources connected to the TV/DBS input jacks)

For the sources connected to the TV/DBS input jacks of this

unit only, you can designate the input mode that is automatically

selected when the power of this unit is switched on.

AUTO: In this position, the AUTO input mode is always selected

when the power of this unit is switched on.

LAST: In this position, the input mode you have selected last time

is memorized and will not be changed even if the power of

this unit is switched on.

See page 39 for details about switching the input mode.

PLAYING A SOURCE

NOTE: If you will use the remote control unit, be sure to use it with

the lid open.

1. Set the master VOLUME control to minimum.

2. Turn the power on.

3. Select an input source.

The selected source is shown by the display panel and the monitor

screen. For the DVD/LD or TV/DBS source, its current input mode is

also shown.

* To change the input mode for the DVD/LD or TV/DBS source,

press the input selector button for the currently selected source

once or more until the desired input mode (AUTO or ANALOG)

is shown on the display panel. (See page 39 for details on

switching the input mode.)

4. Play the source.

5. Increase the setting of the master VOLUME control to your

listening level.

Adjust the BASS, TREBLE, BALANCE controls, etc., or select a

desired sound field program. (See page 42.)

GENERAL OPERATION

Front panel

Remote control

Front panel

Remote control

–dB

VOLUME

Front panel

POWER

DVD

LDVCR 1

TAPE (MD) TV/DBS

DVD/LD

Front panel

Remote control

DVD

LDVCR 1

TAPE (MD) TV/DBS

DVD/LD

SPEAKERS

DIGITAL

SPEAKERS

PRO LOGIC

–dB

VOLUME

MASTER VOLUME

MUTE

English

Notes on using the input selector buttons

• Note that pressing on each input selector button selects the

source which is connected to the corresponding input terminals

on the rear panel.

* To select the source connected to the VIDEO AUX terminals

on the front panel, press VIDEO AUX.

• Once you play a video source, its video image will not be

interrupted even if the input selector button for an audio source

is selected.

• When you select an input source by pressing the

corresponding input selector button, the DSP program (or the

state of no DSP program is used) which was used when the

same input source was selected the last time will automatically

recalled.

Switching the input mode (for DVD/LD and

TV/DBS)

This unit allows you to switch the input mode only for sources

connected to the DVD/LD and TV/DBS input jacks (on the rear of this

unit) that input two or three types of signals to this unit.

The following two input modes are provided.

AUTO: For the source connected to the DVD/LD input jacks:

This mode is automatically selected when you turn on the

power of this unit. In this mode, input signal is

automatically selected by the following order of priority.

1.Digital input signal from the OPTICAL jack

2.Digital input signal from the COAXIAL jack

3.Analog input signal

For the source connected to the TV/DBS input jacks:

This mode is automatically selected when you turn on the

power of this unit if the “AUTO” position is selected on “8.

INPUT MODE” in the SET MENU mode. (See page 37 for

details.) In this mode, input signal is automatically selected

by the following order of priority.

1.Digital input signal from the OPTICAL jack

2.Digital input signal from the COAXIAL jack

3.Analog input signal

ANALOG:

In this mode, only analog input signal is selected even

though digital signal is input at the same time.

Select this mode when you want to use the analog input

signal instead of the digital input signal.

NOTE: For the TV/DBS source only, the input mode selected on the

function “8. INPUT MODE” in the SET MENU mode is selected when

you turn on the power of this unit.

Notes on input mode selection

• To play back a source with the Dolby Digital (AC-3) decoded, set

the input mode to “AUTO”.

• When you want to enjoy a source which has normal 2-channel

signals with a Dolby Pro Logic Surround program, select the

ANALOG mode.

• In the AUTO mode, there may be a case depending on some LD

players or DVD players that when you make a search on a source

encoded with the Dolby Digital (AC-3) during the play and then

the play is restored, sound output is interrupted for a moment

because the digital input signal is selected again.

RECORDING A SOURCE TO

AUDIO/VIDEO TAPE (OR DUBBING

FROM A TAPE TO ANOTHER)

NOTE: If you will use the remote control unit, be sure to use it with

the lid open.

1. Set the REC OUT selector to the SOURCE position.

2. Select the source you want to record.

3. Play the source and increase the setting of the master VOLUME

control to confirm it.

4. Set the tape deck, MD recorder or VCR used for recording to the

recording mode.

Front panel

VCR 2

VIDEO AUX

REC OUT

VCR 1

TV/DBS

PHONO

TUNER

DVD/LD

SOURCE

TAPE (MD)

Front panel

Remote control

DVD

LDVCR 1

TAPE (MD) TV/DBS

DVD/LD

Front panel

Remote control

–dB

VOLUME

MASTER VOLUME

MUTE

English

Regardless of the setting of input selector buttons, when you set

the REC OUT selector to a position other than “SOURCE”, the

source selected by the REC OUT selector can be recorded by other

tape deck (MD recorder) and/or VCRs connected to this unit.

While recording a source by setting the REC OUT selector to the

position other than SOURCE as described above, the following

operations can be made at the same time.

●

You can monitor the audio (or the audio and video) signals being

recorded by selecting the recording unit (TAPE (MD), VCR 1 or

VCR 2) with the corresponding input selector button.

●

You can watch or listen to any other source by selecting it with the

corresponding input selector button.

NOTE: Adjusting the master VOLUME, BASS, TREBLE controls,

etc., or selecting a sound field program has no effect on the material

being recorded.

NOTE: Composite video and S video signals pass independently

through this unit’s video circuits. Therefore, when recording or

dubbing video signals, if your video source unit is connected to

provide only a S video (or only a composite video) signal, you can

record only a S video (or only a composite video) signal on your

VCR.

NOTE: A source that is connected to this unit between digital jacks

only cannot be recorded by a tape deck or VCR connected to this

unit.

NOTE: Please check the copyright laws in your country to record

from records, compact discs, radio, etc. Recording of copyright

material may infringe copyright laws.

If you watch a video software that uses scramble or

encoded signals to prevent it from being dubbed, there may

be a case that display information superimposed on the

picture and/or the picture itself is disturbed due to those

signals.

This unit has 10 programs for digital sound field processing, 6

from actual acoustic environments from around the world, and 4

programs for Audio/Video sources including sources encoded with

Dolby Pro Logic surround or Dolby Digital (AC-3).

When operating on the front panel:

1. If no program name is illuminated on the display panel, press the

EFFECT switch to turn on the digital sound field processor so that a

name of sound field program lights up on the display panel and the

monitor screen.

2. Select the desired sound field program by pressing the

PROGRAM selector.

* The name of selected program lights up on the display panel

and the monitor screen.

When operating on the remote control unit:

Simply pressing a DSP program selector key turns on the digital

sound field processor and select the corresponding program directly.

To enjoy a video source with the Dolby Pro Logic

Surround or Dolby Digital (AC-3) decoded

When you select the program No. 1, 2 or 3, and the input signal

of the source is 2-channel stereo, Dolby Pro Logic Surround is

decoded. When some program is selected and the input signal of the

source is encoded with the Dolby Digital (AC-3), Dolby Digital (AC-3)

is automatically decoded.

* The following indicators on the display panel show you what sound

processing is being made.

* In addition, for the program No. 1, 2 and 3, the name of the program

on the display panel or the monitor screen will change according to

the type of decoding. (See pages 44–45 for details.)

NOTE: If the input signals of source encoded with the Dolby Digital

(AC-3) are in 2-channels only, the sound processing for them is

similar to that for analog or PCM audio signals.

Front panel

SELECTING SOUND FIELD PROGRAMS

Lights up when the Dolby Digital (AC-3) is being decoded and the

signals of selected source encoded with the Dolby Digital (AC-3) is

not in 2-channels.

Lights up when the Digital Sound Field Processing is being made

Lights up when the Dolby Pro Logic Surround is being decoded

EFFECT

Front panel

Remote control

PROGRAM

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

HALL

DIGITAL/

PRO LOGIC

ENHANCED

MOVIE

THEATER

DIGITAL

DSP

PRO LOGIC

DIGITAL

PCM AC

–

DSP

DIGITAL

PCM AC

–

PRO LOGIC

English

CANCELING THE EFFECT SOUND

The EFFECT switch on the front panel and the EFFECT ON/OFF

key on the remote control unit make it simple to compare the normal

stereo sound with the fully processed effect sound.

To cancel the effect sound and monitor only the main sound,

press the EFFECT ON/OFF key or the EFFECT switch. Press the

EFFECT ON/OFF key or the EFFECT switch a second time to

restore normal operation.

NOTES

• If the effect sound is canceled when signals encoded with the

Dolby Digital (AC-3) are input to this unit, signals of all channels

are mixed and are output from the main speakers.

• If the EFFECT switch or the EFFECT ON/OFF key is pressed to

turn effect sounds OFF when the Dolby Digital (AC-3) is decoded,

it may happen that sound is output faintly or not output normally

depending on a source. In that case, press the EFFECT switch or

the EFFECT ON/OFF key to turn effect sounds ON, or use input

signals not encoded with the Dolby Digital (AC-3).

Front panel

Remote control

EFFECT

ON/OFF

1. DOLBY PRO LOGIC

When the input signal is analog or PCM audio ( )

Speaker output: main, center, rear

DOLBY DIGITAL

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear

Reproduces video discs, video tapes and

similar sources which are Dolby Surround

encoded and bear the “DOLBY

SURROUND” logo.

The built-in Dolby Pro Logic Surround

decoder or Dolby Digital (AC-3) decoder

precisely reproduces sounds and sound

effects of a source encoded with Dolby

Surround. The realization of a highly

efficient decoding process improves

crosstalk and channel separation and

makes sound positioning smoother and

more precise.

2. DOLBY PRO LOGIC ENHANCED

When the input signal is analog or PCM audio

()

Speaker output: main, center, rear, front effect

DOLBY DIGITAL ENHANCED

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

Reproduces video discs, video tapes and

similar sources which are Dolby Surround

encoded and bear the “DOLBY

SURROUND” logo.

This program ideally simulates the multi-

surround speaker systems of the 35 mm film

theater. The Dolby Surround decoding and

the digital sound field processing is

precisely performed without altering the

originally designed sound orientation. The

surround effects produced by this sound

field folds the viewer naturally from the rear

to the left and right and toward the screen.

NOTE: If the main channel sound is considerably altered by

overadjustment of the BASS or TREBLE controls, the relationship

with the rear channels may produce an unnatural effect.

DIGITAL

DSP

PRO LOGIC

DIGITAL

PRO LOGIC

DESCRIPTIONS OF THE SOUND FIELD PROGRAMS

The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind that most of these

are precise digital recreations of actual acoustic environments. The data for them was recorded at the locations described using

sophisticated sound field measurement equipment.

* The channel level balance between the left rear speaker and the right rear speaker may vary depending on the sound field you are

listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments.

English

3. MOVIE THEATER

When the input signal is analog or PCM audio

()

Speaker output: main, center, rear, front effect

DIGITAL MOVIE THEATER

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

Ideal for reproducing video discs, video

tapes and similar sources which are Dolby

Surround encoded and bear the “DOLBY

SURROUND” logo.

This program is ideal for precisely

reproducing the sound design of the newest

70 mm/Dolby Digital multi-track films. The

sound field is made to be similar to that of

the newest movie theaters, so the

reverberations of the sound field itself are

restrained as much as possible. The three

dimensional feeling of the sound field is

emphasized, and dialog is precisely oriented

on the screen. You can enjoy watching Sci-

Fi, adventure movies, etc. with much

presence.

4. TV SPORTS

When the input signal is analog or PCM audio ( )

Speaker output: main, center, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This program is furnished with a tight sound

field in which the sound will not spread

excessively on the front side, but the rear

surround side produces a dynamic sound

expansion. This program is the most suitable

for sports programs.

5. STADIUM

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This program gives you long delays between

direct sounds and effect sounds, and

extraordinarily spacious feel of a large

stadium.

6. DISCO

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This program recreates the acoustic

environment of a lively disco in the heart of

a very lively city. The sound is dense and

highly concentrated. It is also characterized

by a high-energy, “immediate” sound.

DIGITAL

DSP

DIGITAL

DSP

DIGITAL

DSP

DIGITAL

DSP

PRO LOGIC

7. ROCK CONCERT

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This program is ideally suited for rock music.

You will experience a very dynamic or lively

sound field.

8. JAZZ CLUB

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This is a small, cozy jazz club with a low

ceiling. The sound is very close and intimate.

9. CHURCH

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

This program recreates the acoustic

environment of a big church with a high

pointed dome and columns along the sides.

This interior produces very long

reverberations.

10.CONCERT HALL

When the input signal is analog or PCM audio ( )

Speaker output: main, rear, front effect

When the input signal is Dolby Digital ( )

Speaker output: main, center, rear, front effect

In this program, the center will appear to be

deep behind the main speakers, creating an

expansive large hall ambience. Orchestra

and opera music are suited for this sound

field.

NOTE: If the FRONT MIX switch on the rear panel is set to the

“ON (5ch)” position, no sound is output from the front effect

speakers, no matter what program is selected.

Besides, if the “PHNTM” position is selected on “4. CENTER

SPEAKER” in the SET MENU mode, no sound is output from

the center speaker(s).

DIGITAL

DSP

DIGITAL

DSP

DIGITAL

DSP

DIGITAL

DSP

English

In using the digital sound field processor including the Dolby Pro

Logic Decoder or the Dolby Digital (AC-3) Decoder, you can adjust

delay time between the main sound and effect sound, and each

speaker output level as you prefer.

NOTE: These adjustments can be made only when the effect

sound is on. If and/or (or ) is not

illuminated on the display panel, press the EFFECT switch on the

front panel or the EFFECT ON/OFF key on the remote control unit

so that at least one of those indicators lights up on the display

panel.

1. If you will use the remote control unit, set the TIME/LEVEL·SET

MENU switch to the TIME/LEVEL position on the remote control unit.

NOTE: Be sure to use the remote control unit with the lid open.

2. Press once or more until the name of item on which you will make

an adjustment appears on the display panel.

Whenever pressed, the selection changes as follows.

* Depending on a mode of this unit, the number of selections is

reduced.

* Pressing the key on the remote control unit changes the

selection in the reverse order.

3. Adjust its level.

4. Repeat step 2 and 3 to make adjustments on other items.

PRO LOGIC

DIGITAL

DSP

ADJUSTING DELAY TIME AND EACH SPEAKER OUTPUT LEVEL

Remote control

TIME/LEVEL

SET MENU

Front panel

Remote control

DELAY TIME

FRONT LEVEL

CENTER LEVEL

R SUR. LEVEL

L SUR. LEVEL

SWFR LEVEL

(Delay time)

(Center speaker output

level)

(Right rear speaker output

level)

(Left rear speaker output

level)

(Front effect speaker

output level)

(Subwoofer output level)

Remote control

Front panel

DELAY

SWFR

Adjusting delay time

You can adjust the time difference between the beginning of the

sound from the main speakers and the beginning of the effect

sound from the rear or front effect speakers.

The larger the value, the later the effect sound is generated.

This adjustment can be made to all programs individually.

NOTES

• Adding too much delay will cause an unnatural effect with some

sources.

• When the –/+ button is pressed, sound is momentarily

interrupted.

Adjusting output level of the front effect, center,

right rear and left rear speakers, and subwoofer

If desired, you can adjust the sound output level of the each

speaker even if the output level is already set in “SPEAKER

BALANCE ADJUSTMENT” on pages 33 to 34.

NOTES

• Output level of the front effect speakers cannot be adjusted

when the program DOLBY PRO LOGIC (DOLBY DIGITAL) is

selected.

• Output level of the center speaker cannot be adjusted when the

program STADIUM, DISCO, ROCK CONCERT, JAZZ CLUB,

CHURCH or CONCERT HALL is selected, and the input signal

is analog, PCM audio or encoded with the Dolby Digital (AC-3)

in 2-channels.

• Once the output level is adjusted, the level value will be the

same in all the digital sound field programs.

NOTE

The values of the delay time and each speaker level you set the

last time will remain memorized even when the power of this unit is

off.

However, if the power cord is kept disconnected for more than one

week, these values will be automatically changed back to the

original factory settings.

Program

1. DOLBY PRO LOGIC

DOLBY DIGITAL

2. PRO LOGIC ENHANCED

DOLBY DIGITAL ENHANCED

3. MOVIE THEATER

DIGITAL MOVIE THEATER

4. TV SPORTS

5. STADIUM

6. DISCO

7. ROCK CONCERT

8. JAZZ CLUB

9. CHURCH

10. CONCERT HALL

Control range (ms)

15 to 30

0 to 15

15 to 30

0 to 15

15 to 30

1 to 50

Speakers

FRONT

CENTER

RIGHT SURROUND

LEFT SURROUND

SUBWOOFER

Preset value

Control range (dB)

MIN, –20 to +10

MIN, –20 to 0

English

If you use the SLEEP timer of this unit, you can make this unit

turn off automatically. When you are going to sleep while enjoying

a broadcast or other desired input source, this timer function is

helpful.

NOTES

• The SLEEP timer can be controlled only with the remote

control unit.

• The components on which the SLEEP timer is effective are the

sources connected to the SWITCHED AC OUTLET(S) on the

rear panel of this unit.

To set the SLEEP time

1. Press the SLEEP key.

Press once or more to select the desired SLEEP time.

Whenever the SLEEP key is pressed, the SLEEP time will

change as follows.

After a while, the display returns to the indication before the

SLEEP timer is set.

2. The unit will be turned off automatically at the selected SLEEP

time.

To cancel the selected SLEEP time

Press the SLEEP key once or more so that “SLEEP OFF”

appears on the display panel. (It will soon disappear and the

“SLEEP” indicator will go off from the display panel.)

NOTE

The SLEEP timer setting can also be canceled by turning off the

power with the POWER switch or disconnecting the power plug of

this unit from the AC outlet.

SETTING THE SLEEP TIMER

120 90 60 30

(Minutes)

The SLEEP timer is off (OFF).

(The state before the SLEEP

key is pressed.)

SLEEP

Indicates the SLEEP time.

Lights up.

The remote control unit provided with this unit is designed to

control all the most commonly used functions of this unit. If the CD

player, tape deck, LD player etc. connected to this unit are

YAMAHA components designed for remote control compatibility,

then this remote control unit will also control various functions of

each component.

* For basic operations, use the remote control unit with the lid

open.

NAMES OF KEYS AND THEIR FUNCTIONS

1 Tape deck keys

Controls tape deck.

(The A/B/C switch (

G) should be set to the “A” position.)

* DIR A, B and A/B are applicable only to double cassette tape

deck.

* For a single cassette deck with automatic reverse function,

pressing DIR A will reverse the direction of tape running.

2 CD/LD player keys

Controls compact disc player or LD player.

(To control compact disc player, set the A/B/C switch (

G) to the

“A” position. To control LD player, set the A/B/C switch (

G) to the

“C” position.)

* DISC is applicable only to compact disc changer.

* STOP is applicable only to LD player.

3 Tuner keys

Controls tuner.

(The A/B/C switch (

G) should be set to the “A” position.)

+: Selects higher preset station number.

–: Selects lower preset station number.

A/B/C/D/E: Selects the group (A – E) of preset station numbers.

REMOTE CONTROL UNIT

BASIC OPERATIONS (When the lid is open)

Side panel

Lid is open.

MACROQUICK

OFFSLOW

LIGHT

TAPE

A/B

REC/PAUSE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

DIGITAL/

PRO LOGIC

ENHANCED

MOVIE

THEATER

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

HALL

TIME/LEVEL

SET MENU

TEST

SLEEP

SP B

SP A

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

English

4 DSP program selector keys

Selects a DSP program when the built-in digital sound field

processor (including the Dolby Pro Logic Surround Decoder or the

Dolby Digital (AC-3) Decoder) is on.

5 TEST key

Used when you make the speaker balance adjustment to

maximize the performance of your audio/video system including

this unit. (For details, refer to page 33–34.)

6 SP A and SP B keys

Select the main speakers A or B (or both A and B) you will use by

pressing the corresponding key “SP A” or “SP B” (or both keys) so

that “SPEAKERS A” or “SPEAKERS B” (or both of them) lights up

on the display panel. To cancel selected speakers, press the

corresponding key so that the corresponding indicator goes off

from the display panel.

7 SLEEP timer key

This key is used to turn the built-in SLEEP timer on and off, and to

set the SLEEP time. (See page 49 for details.)

8 TIME/LEVEL·SET MENU switch

Set to the TIME/LEVEL position when you will make an adjustment

on delay time, center speaker output level, rear speaker output

level, front effect speaker level or subwoofer level. Set to the SET

MENU position when you will make an adjustment or setting

change on a function in the SET MENU mode.

9 SYSTEM POWER and OFF keys

While the power is on, pressing the OFF key switches the unit from

the power-on mode to the standby mode and pressing the

SYSTEM POWER key switches the unit from the standby mode to

the power-on mode. (In the standby mode, the standby indicator

on the front panel is illuminated.)

0 RESET button

This button is inside the battery compartment.

Press this button to “reset” the internal microcomputer which

controls remote control operations. Microcomputer “reset” is

necessary when the remote control freezes.

* Pressing the RESET button will not erase learned functions.

A MASTER VOLUME (up) and (down) keys

Turns the volume level up and down.

B MUTE key

When pressed, this key mutes the volume level. To resume the

original volume level, press this key again.

While muting, the indicator on the VOLUME control flashes

continuously.

C / and –/+ keys

(up) and (down) keys change items (or functions) in the

mode selected by the TIME/LEVEL·SET MENU switch. – and +

keys make an adjustment or setting change on the item (or

function) selected by the or key.

D EFFECT ON/OFF key

Switches on/off the digital sound field processor (including the

Dolby Pro Logic Surround Decoder or the Dolby Digital (AC-3)

Decoder).

E Input selector keys

Selects input source.

RESET button

F A/B/C indicators

The position (A, B or C) selected by the A/B/C switch is shown in

red.

G A/B/C switch

This switch must be used only when the lid of the remote control

unit is open. (This switch will not function when the lid is closed.)

Normally, set this switch to the “A” position. When controlling a

Yamaha LD player by using the CD/LD player keys (

2), set this

switch to the “C” position.

H TRANSMIT/LEARN indicator

Lights up when the remote control unit is transmitting infrared

signals (when a command key is pressed).

I LIGHT key

If this key is pressed, some of the keys on the remote control unit

light up for about 5 seconds. If this key is pressed while those keys

are lighting up, they stop lighting.

NOTE

When using the keys to control Yamaha components, identify

them with your component’s keys. If these keys are identical,

their functions will be the same. For each key function, refer to

the corresponding instruction in your component’s manual.

LEARNING NEW CONTROL FUNCTIONS

(When the lid is open)

This is a learning remote control unit. The shaded keys in

the illustration shown right can be programmed to “learn” control

functions from other remote control units. By learning key-

functions from other remote control unit, this unit can then be used

in place of one or more other remote control units, thus making

operation of your various audio and video components more

convenient.

Some of the “learning-capable” keys are originally empty and

others have already been preset with functions to control this unit

and other Yamaha components. You can store new functions to

them (in place of preset functions) as desired.

* See pages 61 to 62 for the learning method.

* See pages 64 to 65 for clearing a learned function (or all

learned functions).

NOTE

If the memory capacity of the remote control unit becomes full, no

further learning is possible even if some learning-capable keys are

not occupied with new functions. If, for example, you store only

Yamaha codes into this remote control unit, up to about 50

functions can be stored. Store new functions to the learnable-

capable keys which are useful for you.

English

These buttons are used for learning a new function or clearing a learned

function (or all learned functions). See pages 61 to 65 for details.

Keys which can have three functions (1, 2, 3, 4)

In the “Learning-capable” keys, the keys of groups numbered

1–4 in the illustration at left can have three functions. This is

because they have three memory areas (A, B and C). (One

function per area.) You can store new functions into the area B and

C, and use three functions on a key by switching the memory

areas with the A/B/C switch. (Area A cannot learn a new function.)

To use these keys:

1. Before using a key, select the area A, B or C of the key on

which the function you want to use is stored by using the A/B/C

switch.

2. Press the key.

The original factory settings of these keys are as follows.

NOTE

The area A of any key cannot learn a new function. To store a new

function to a key, store it into the area B or C.

Preset with functions

for controlling a

Yamaha tape deck.

Preset with functions

for controlling a

Yamaha CD player.

(STOP is empty.)

Preset with functions

for controlling a

Yamaha tuner.

Preset as the DSP

program selector keys

(1–9, 0) and the TEST

key.

(+10 is empty.)

Empty

Preset as the DSP

program selector keys

(1–9, 0) and the TEST

key.

(+10 is empty.)

Empty

Preset with functions

for controlling a

Yamaha LD player.

(DISC is empty.)

Empty

Preset as the DSP

program selector keys

(1–9, 0) and the TEST

key.

(+10 is empty.)

The position of A/B/C switch

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

HALL

TIME/LEVEL

SET MENU

TEST

SLEEP

SP B

SP A

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

A/B

REC/PAUSE

DISCSTOP

DIGITAL/

PRO LOGIC

ENHANCED

MOVIE

THEATER

A/B/C switch

Lid is open.

Empty keys (1, 2)

These are empty keys. Each key can learn a function from

another remote control unit.

For example, the TV key is useful for storing the function of your

TV’s power switch, and the VCR key can be used for your VCR’s

power switch.

NOTE

If a key which has a preset function learns a new function, the

preset function will not be deleted, but disabled. When the learned

function is cleared, the preset function is restored. (For information

on clearing a learned function, refer to pages 64 to 65.)

About the marks shown on the remote control unit

The marks on the remote control unit signify functions of keys,

input sources, etc.

Examples)

(tape): Shows tape deck, VCR, etc.

(disc): Shows CD player, LD player, etc.

(radio wave): Shows tuner, TV/BS tuner, etc.

These marks are helpful for storing new functions.

Examples)

• The area B of keys

1 is suitable for storing functions to control

your VCR.

• The area B of keys

3 is suitable for storing functions to control

your TV/BS tuner.

About the lighting of keys

When you press an input selector key, it lights up for about 3

seconds.

When an input selector key in the group of selected memory

area (A, B or C) is pressed, the mark of key group (

1–3) which

is the same as the mark of the selected input selector key lights up

for about 3 seconds.

Example)

Conversely, when a key of group

1–3 is pressed, its mark

and the input selector key with the same mark in the group of the

selected memory area light up for about 3 seconds.

This feature may be helpful for you if you store functions for

controlling an input source to a group of keys whose mark lights up

when the corresponding input selector key is pressed.

TAPE

A/B

REC/PAUSE

TUNER

VCR 1

DIR

DISCSTOP

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Red (This shows that the

memory area A is

selected.)

Lights up.

English

When the lid of the remote control unit is closed, you

can easily operate Yamaha components including learned

functions by using the OPERATION CONTROL keys.

When the lid is closed, the OPERATION CONTROL

keys substitute for the keys of group numbered

1, 2 or

3 and the (+10) key on the left illustration. To use

these keys, you do not have to switch the A/B/C switch. The

functions which the OPERATION CONTROL keys carry out

are determined by which input selector key was pressed

before you use the OPERATION CONTROL keys.

NOTE

When the lid is closed, the EFFECT, MASTER VOLUME,

MUTE, TV and VCR keys will function in the same way as

when the lid is open.

* If the MACRO switch on the side of the remote control

unit is set to “OFF”, when the lid is closed, the SYSTEM

POWER and OFF keys also will function in the same way

as when the lid is open.

USING OPERATION CONTROL KEYS (When the lid is closed)

REMOTE CONTROL

TRANSMITTER

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

TV/DBS

VCR

OFF

SYSTEM

POWER

MUTE

MASTER

VOLUME

OPERATION

CONTROL

EFFECT

TRANSMIT

TAPE

A/B

REC/PAUSE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

HALL

TIME/LEVEL

SET MENU

TEST

SLEEP

SP B

SP A

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

DIGITAL/

PRO LOGIC

ENHANCED

MOVIE

THEATER

(+10)

Input selector keys

OPERATION CONTROL keys

Lid is closed.

These keys are originally empty. If these keys have learned functions, pressing

them executes those learned functions.

See the table below for a combination of an input selector key and key functions which the OPERATION CONTROL keys carry out.

(Also, refer to the table on page 53.)

Pressing the “V-AUX” or “PHONO” input selector key has no effect on the OPERATION CONTROL keys.

Selected input selector

Key functions which the OPERATION CONTROL keys carry out

Functions in area A of keys 1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area A of keys 2 (except STOP, DISC, and )

Functions in area A of keys 3 and (+10)

Functions in area B of keys 1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area B of keys 2 (except STOP, DISC, and )

Functions in area B of keys 3 and (+10)

Functions in area C of keys 1 (except REC/PAUSE, A/B, DIR A and B)

Functions in area C of keys 2 (except STOP, DISC, and )

Functions in area C of keys 3 and (+10)

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

TV/DBS

Examples of operations controlled by using the OPERATION

CONTROL keys

To operate a Yamaha CD player

1. Press the “CD” input selector key.

2. Use the OPERATION CONTROL keys. (They carry out the

functions in area A of keys

2.)

To operate your VCR

1. Press the “VCR” input selector key.

2. Use the OPERATION CONTROL keys. (They carry out the

functions in area B of keys 1. This area is originally preset

with no function. You must store the functions related to

controlling the VCR in area B of keys

1 beforehand.)

OPERATION

CONTROL

Play

Skip to

previous track

Skip to next track

Pause or Stop

OPERATION

CONTROL

Play

Rewind

Fast forward

Pause or Stop

English

NOTES

• If the OPERATION CONTROL keys substitute for keys which

has no function (empty), no command is carried out.

According to your plan, store functions from other remote

control units into an empty area of those keys. (Refer to pages

61 to 62 for the learning method.)

• While playing an audio/video unit, if you want to operate

another unit by using the remote control unit (for example, if

you want to rewind a tape on your VCR while listening to a CD),

you should open the lid of the remote control unit and use the

A/B/C switch and the corresponding keys.

(If you press an input selector key with the lid closed to change

the functions of the OPERATION CONTROL keys to the

functions for controlling a VCR, the input of currently playing

CD source is canceled.)

About the lighting of keys

When an input selector key is pressed, the pressed key and

only the available OPERATION CONTROL keys (which substitute

for the keys stored with the preset functions or learned functions)

light up for about 3 seconds. So you can know what keys are

available at a glance.

Conversely, when an OPERATION CONTROL key is pressed,

all of the available OPERATION CONTROL keys and the currently

selected input selector key light up.

TUNER

OPERATION

CONTROL

MACRO OPERATIONS (When the lid is

closed)

“Macro” is a command which defines a sequence of several

operations.

The keys shown in the right illustrations (as “preset macro

keys”) are also preset with macros, in addition to individual

functions.

Each macro key is preset so that simply pressing it alone will

carry out several functions of other keys on this remote control

unit sequentially. (To know what key functions are sequentially

carried out by pressing each preset macro key, see the next

page.)

Macros can be used only when the lid is closed and the

MACRO switch is set to “SLOW” or “QUICK”. (If “OFF” is

selected, no macro will function even if the lid is closed.)

Preset macro keys are originally preset with macros. If you

prefer, however, you can change the contents of a macro key by

storing a desired series of functions on it. You can store up to

seven functions onto a macro key. (See page 63 for the learning

method.)

Setting the MACRO switch

OFF: In this position, no macro will function even if the lid of

remote control unit is closed.

QUICK:In this position, when a macro key is pressed, each

command is transmitted at 0.5 second intervals.

SLOW: In this position, when a macro key is pressed, each

command is transmitted at 3 second intervals.

REMOTE CONTROL

TRANSMITTER

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

TV/DBS

VCR

OFF

SYSTEM

POWER

MUTE

MASTER

VOLUME

OPERATION

CONTROL

EFFECT

TRANSMIT

MACROQUICK

OFFSLOW

LIGHT

TAPE

A/B

REC/PAUSE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

EFFECT

ON/OFF

TV/DBS

DIR

DISCSTOP

TRANSMIT

/LEARN

LEARNCLEAR MACRO

PRESET

A/B/C/D/E

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

HALL

TIME/LEVEL

SET MENU

TEST

SLEEP

SP B

SP A

MASTER VOLUME

VCR

OFF

SYSTEM

POWER

+10

MUTE

REMOTE CONTROL

TRANSMITTER

DIGITAL/

PRO LOGIC

ENHANCED

MOVIE

THEATER

Lid is closed.

(Set the MACRO switch to

“QUICK” or “SLOW”.)

Preset macro keys

MACRO switch

English

Macro key

1st 2nd

–

3rd

–

Function of the key which operates when a macro key is pressed

Preset macro keys and the key functions which they carry out sequentially are as follows. (Also, refer to the table on

page 53.)

SYSTEM

POWER

OFF

SYSTEM

POWER

OFF

VCR

Macro key

1st

(Turning the power of this unit on)

2nd

(Selecting an input source)

3rd

(Playing a source)

“”on area A of keys 1

“”on area A of keys 2

–

“”on area B of keys 1

“”on area B of keys 2

–

“”on area C of keys 1

“”on area C of keys 2

–

Function of the key (and area) which operates when a macro key is pressed

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

TV/DBS

TAPE

TUNER

VCR 1

VCR 2

DVD/LD

V-AUX

PHONO

TV/DBS

SYSTEM

POWER

NOTES

• A key in which no function is stored will carry out no command.

• If it occurs that this unit will not receive the second command

because the internal operation of the first command takes a

long time, set the MACRO switch to the “SLOW” position, or

add no function or repeat the same command between the first

command and the next command.

• If you will program the power on/off switching function of TV,

VCR, etc. as part of a macro sequence, note that it switches

the current mode to the other (“on” to “off”, or “off” to “on”).

For example, when you press the macro key, if the power of TV,

VCR, etc. is already on, the power will be turned off even

though you may not want it to do so.

• Once you press a macro key, this unit will not receive the

command of another key (even if it is pressed) until this unit

finishes carrying out all commands of the macro key. Take

notice of this especially when the MACRO switch is in the

“SLOW” position.

• Once you press a macro key, you must keep the remote control

unit directed at the main unit’s remote control sensor until the

remote control unit finishes transmitting all command signals of

the macro key.

• You can use the OPERATION CONTROL keys also while using

the macro functions.

English

1. Place this remote control unit and the other remote control unit

so that they face each other.

2. Press the LEARN button using the point of a mechanical pencil

etc.

* If there is no operation for about 30 seconds after the LEARN

button is pressed, the TRANSMIT/LEARN indicator flashes

rapidly and the current mode is canceled. If this occurs,

repeat this step.

3. If necessary, select the memory area by using the A/B/C switch

on the side panel of the remote control unit.

4. Press the key on this remote control unit in which you will store

a new function.

* If a key which cannot learn another function is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the current

mode is canceled. If this occurs, repeat this step.

* If there is no operation for about 30 seconds after a key is

pressed, the TRANSMIT/LEARN indicator flashes rapidly and

the mode before you began learning operations is restored. If

this occurs, restart from step 2.

LEARNING A NEW FUNCTION

V-AUX

PHONO

EFFECT

ON/OFF

123

SPORTS

STADIUM

DISCO

456

ROCK

JAZZ CLUB

CHURCH

789

TEST

+10

Lights up.

V-AUX

PHONO

EFFECT

ON/OFF

123

ORTS

STADIUM

DISCO

Z CLUB

CHURCH

EST

This remote control

unit

Other remote

control unit

About 5–10 cm

(2–4 in.)

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

5. Press and hold the key (on the other remote control unit) which

has the function you want to store.

* When learning is finished, the TRANSMIT/LEARN indicator

stops lighting and then begins flashing slowly.

* If a signal is not successfully received, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

prior to step 4 is restored. If this occurs, restart from step 4.

* If memory capacity is full, the TRANSMIT/LEARN indicator

flashes rapidly to show you that learning is impossible, and

then the mode before you began learning operations is

restored.

6. Repeat step 3–5 to store more functions.

7. When you finish the learning operation, press the LEARN

button.

NOTES

• Newly learned functions will replace previously learned

functions.

• If there is no more room in the memory area for a function to be

learned, the TRANSMIT/LEARN indicator will flash rapidly. In

this case, even if some keys are not occupied with functions

from other remote control units, no further learning is possible.

• If the lid is closed while learning and about 5 seconds pass, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

before you began learning operations is restored. If this occurs,

restart from step 2. However, if the lid is opened within 5

seconds, the mode before the lid was closed is restored.

• There may occasionally be instances in which, due to the

signal-coding and modulation employed by the other remote

control unit, this remote control unit will not be able to “learn” its

signals.

LEARNCLEAR MACRO

V-AUX

PHONO

EFFECT

ON/OFF

123

SPORTS

STADIUM

DISCO

456

OCK

JAZZ CLUB

CHURCH

TEST

English

A new macro can be programmed onto any preset macro key in

place of preset functions. (See page 58 to know what keys are

preset macro keys.) You can make as many as 13 new macro

keys. A macro key can learn as many as seven functions of other

keys.

NOTE

If you store a continuous command such as lowering of volume

level, it will become a short command when it is carried out as a

part of macro.

1. Press the MACRO button using the point of a mechanical

pencil etc.

* If there is no operation for about 30 seconds after the

MACRO button is pressed, the TRANSMIT/LEARN indicator

flashes rapidly and the mode before you pressed the MACRO

button is restored. If this occurs, press the MACRO button

again.

2. Press a preset macro key on which you want to make a new

macro.

* If a key other than a preset macro key is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the current

mode is canceled. If this occurs, repeat this step.

3. Press a key whose function you want to store as the first

function of the new macro.

* If a key whose function cannot be stored as a command of

macro is pressed, the TRANSMIT/LEARN indicator flashes

rapidly and the current mode is canceled. If this occurs,

repeat this step.

* If about 30 seconds pass before a key is pressed, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

before you began learning operations is restored. If this

occurs, restart from step 1.

4. Repeat step 3 to store the second, the third and more

functions. You can store up to seven key functions in series as a

macro.

* If the seventh key function has been learned, the

TRANSMIT/LEARN indicator flashes rapidly and the mode

before you began learning operations is restored. (This shows

that the key has completed learning a series of functions as a

macro.) If this occurs, you do no have to follow the next step.

5. When you finish learning, press the MACRO button.

MAKING A NEW MACRO

Goes off.

(When learning is finished,

this indicator lights up again.)

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

TRANSMIT

/LEARN

Lights up.

SYSTEM

POWER

TRANSMIT

/LEARN

LEARNCLEAR MACRO

It is recommended to write down new key functions you

stored on the provided user function stickers and paste them

on the reverse side of the remote control unit or the reverse

side of the remote control unit’s lid.

Memory back-up

All of the learned functions will be retained while you replace

the batteries. However, if no batteries are installed for a few

hours, the learned functions will be erased and will have to be

learned again.

CLEARING LEARNED FUNCTIONS

To Clear a Learned Function

1. To clear a learned key function, press the LEARN button using

the point of a mechanical pencil, etc.

To clear a macro you made, press the MACRO button.

2. Press and hold the CLEAR button using the point of a

mechanical pencil, etc.

3. Holding the CLEAR button pressed, press and hold the key

whose function you want to clear until the indicator flashes 3 times.

To clear two or more functions sequentially, do not release the

CLEAR button pressed, and repeat this step.

NOTE

If you clear a learned function of a key, the originally preset

function of the key is restored (except the keys which are originally

preset with no function.)

TRANSMIT

/LEARN

LEARNCLEAR MACRO

Flashes slowly.

TRANSMIT

/LEARN

Flashes.

REMOTE CONTROL

TRANSMITTER

English

To Clear All Learned Functions

1. Select the kind of key functions all of which you want to clear by

using the MACRO switch on the side panel of the remote control

unit.

OFF: Select this position if you want to clear all of the learned

functions except macros.

QUICK:Select this position if you want to clear all of the macros

you made only.

SLOW: Select this position if you want to clear all of the learned

functions including macros.

2. Press the CLEAR button using the point of a mechanical pencil,

etc.

* If one of the following operation is made after you press the

CLEAR button, the TRANSMIT/LEARN indicator flashes

rapidly and the current mode is canceled. If this occurs, press

the CLEAR button again.

• MACRO switch is switched to another position.

• Another key is pressed.

• There is no operation for about 30 seconds.

3. Press and hold the CLEAR button again. While holding the

CLEAR button pressed, press and hold the MASTER VOLUME

and keys simultaneously until the indicator flashes 7 times.

MACROQUICK

OFFSLOW

LEARNCLEAR MACRO

TRANSMIT

/LEARN

Flashes slowly.

MUTE

TRANSMIT

/LEARN

Flashes.

TROUBLESHOOTING

PROBLEM

Power does not come on.

The unit turns off suddenly soon after the

power is turned on.

Hum.

No sound.

No sound from the effect speakers.

No sound from the front effect speakers.

No sound from the center speaker.

Poor bass reproduction.

The sound suddenly goes off.

The volume level cannot be increased, or

sound is distorted.

The sound field cannot be recorded.

This unit will not operate properly.

POSSIBLE CAUSE

AC cord not properly plugged in.

The IMPEDANCE SELECTOR switch on the rear

panel is not set to the upper or the lower end

exactly.

Bad cable connection.

Bad or incorrect input connection.

Incorrect input source selection.

Digital signals other than PCM audio or the Dolby

Digital (AC-3) encoded signals which this unit

cannot reproduce are input to this unit by playing a

CD-ROM etc.

The EFFECT switch is set off.

A Dolby Surround decoding program is being used

with material not encoded with Dolby Surround.

The FRONT MIX switch is set to “ON”.

The sound field program No. 1 “DOLBY PRO

LOGIC (DOLBY DIGITAL)” is selected.

The CENTER SPEAKERS mode is in “PHNTM”.

One of the sound field programs No. 5 to No. 10 is

selected when the input signal of source is 2-

channel stereo (analog/PCM).

The input signals of source encoded with the Dolby

Digital (AC-3) do not have center channel signals.

The LFE/BASS OUT mode is in the SWFR or

BOTH position, though your system does not

include a subwoofer.

Output mode selection for each channel (MAIN,

CENTER or REAR) is improper.

The protection circuit has activated because of

short circuit etc.

The power to the component connected to the

REC OUT jacks of this unit is off.

It is not possible to record the sound field on a tape

deck connected to this unit’s TAPE REC OUT

jacks.

The internal microcomputer has been frozen by an

external electric shock (lightning, excessive static

electricity, etc.) or power supply with low voltage.

WHAT TO DO

Carefully plug AC plug into outlet.

Set the switch to the upper or the lower end exactly.

Firmly plug in all connection cables.

Check connections.

Select the appropriate input source with the input selector buttons.

Play a source whose signals this unit can reproduce.

Press the EFFECT switch to turn it on.

Use a different sound field program.

Set the FRONT MIX switch to “OFF”.

Select another program.

Select the appropriate mode.

Select another program.

Refer to the instructions for the source currently played.

Select the MAIN position.

Make output mode selections suitable for your speaker system.

Turning the unit off and then on will reset the protection circuit.

Turn the power to the component on.

Unplug the AC power cord from the wall AC outlet, and then plug in again

after about one minute.

English

PROBLEM

A source cannot be recorded by a tape deck

or VCR connected to this unit.

Noise from nearby TV or tuner.

The sound is degraded when listening with

the headphones connected to the compact

disc player or cassette deck that are

connected with this unit.

The remote control unit does not work.

The remote control unit does not function

properly.

Learning cannot be made successfully.

(The TRANSMIT/LEARN indicator does not

light up or flash.)

Continuous functions such as volume are

learned, but operate only for a moment

before stopping.

POSSIBLE CAUSE

The source unit is connected to this unit between

digital jacks only.

This unit is too close to the affected equipment.

The power to this unit is off.

The batteries of this remote control unit are

weak.

The internal microcomputer “freezes”.

Wrong distance or angle.

Direct sunlight or lighting (of an inverter type of

flourescent lamp etc.) is striking the remotecontrol

sensor of the main unit.

The internal microcomputer “freezes”.

The batteries of this remote control unit and/or

the other remote control unit are weak.

The distance between the two remote control

units is too long or too short.

The signal coding or modulation of the other

remote control unit is not compatible with this

remote control unit.

Memory capacity is full.

The internal microcomputer “freezes”.

Learning process incomplete.

WHAT TO DO

Make additional connection between analog jacks.

Move the unit further away from the affected equipment.

Turn the power to this unit on.

Replace the batteries with new ones and press the RESET button on

the remote control unit.

Press the RESET button on the remote control unit.

The remote control unit will function from a maximum range of 6 meters,

no more than 30 degrees off-axis from the front panel.

Change position of the main unit.

Press the RESET button on the remote control unit.

Replace the batteries (and press the RESET button for this remote

control unit).

Place the remote control units with the proper distance.

Learning is not possible.

Further learning is not possible without deleting unnecessary

commands.

Press the RESET button on the remote control unit.

Be sure to press and hold the function key on the other remote control

until the TRANSMIT/LEARN indicator begins flashing slowly.

Minimum RMS Output Power Per Channel

Main (20 Hz – 20 kHz 0.02% THD 8Ω) ........................................... 80W+80W

Center (20 Hz – 20 kHz 0.02% THD 8Ω) ................................................. 80W

Front Effect (1 kHz 0.05% THD 8Ω)..................................................25W+25W

Rear (20 Hz – 20 kHz 0.02% THD 8Ω) ........................................... 80W+80W

Dynamic Power Per Channel

(by IHF Dynamic Headroom Measuring Method)

MAIN L/R (8Ω/6Ω/4Ω/2Ω) ............................................. 130W/160W/200W/240W

Maximum Output Power [General model]

MAIN L/R (1 kHz 10% THD 8Ω) ....................................................... 128W+128W

DIN Standard Output Power Per Channel [Europe model]

MAIN L/R (1 kHz 0.7% THD 4Ω) ............................................................. 128W

IEC Power [Europe model]

MAIN L/R (1 kHz 0.015% THD 8Ω) ......................................................... 100W

Power Band Width

MAIN L/R (40W 0.08% THD 8Ω) ............................................ 10 Hz to 50 kHz

Damping Factor

MAIN L/R (20 Hz – 20 kHz 8Ω, SPEAKERS A) ........................... 200 or more

Input Sensitivity/Impedance (100W/8Ω)

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX............. 150 mV/47 kΩ

PHONO MM.................................................................................2.5 mV/47 kΩ

MAIN IN ..............................................................................................1V/47 kΩ

Maximum Input Signal

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX

(1 kHz 0.5% THD, EFFECT ON) ............................................... 2.2V or more

PHONO MM (1 kHz 0.04% THD)............................................ 110 mV or more

Output Level/Impedance

REC OUT.................................................................................. 150 mV/2.7 kΩ

PRE OUT

MAIN............................................................................................... 1V/1.2 kΩ

SUBWOOFER (MAIN SPEAKERS: SMALL) .............................. 4.0V/1.2 kΩ

Headphone Jack Rated Output/Impedance

Output Level (CD Input 150 mV, RL=8Ω).................................................. 0.5V

Impedance .............................................................................................. 440Ω

Frequency Response (20 Hz – 20 kHz)

MAIN IN ............................................................................................. 0±0.5 dB

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to MAIN L/R SP OUT

........................................................................................................... 0±0.5 dB

RIAA Equalization Deviation (20 Hz – 20 kHz)

PHONO MM ........................................................................................0±0.5 dB

Total Harmonic Distortion

PHONO MM to REC OUT, 20 Hz – 20 kHz, 1V.......................... 0.01% or less

MAIN IN to SP OUT (MAIN L/R, CENTER), 20 Hz–20 kHz, 40W/8Ω

.................................................................................................. 0.008% or less

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT

(MAIN L/R, CENTER), 20 Hz – 20 kHz, 40W/8Ω...................... 0.015% or less

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT

(REAR L/R), 1 kHz, 40W/8Ω......................................................... 0.3% or less

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT

(FRONT L/R), 1 kHz, 12.5W/8Ω ................................................... 0.3% or less

DIGITAL IN (DVD/LD) to SP OUT (MAIN L/R, CENTER, REAR L/R),

20 Hz – 20 kHz, 40W/8Ω ............................................................ 0.03% or less

Signal-to-Noise Ratio (IHF-A Network)

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT

(Input Shorted 150 mV) (EFFECT OFF) ................................. 96 dB or more

PHONO MM to REC OUT (Input Shorted 5 mV)

[Europe, U.K. and Australia models]........................................ 82 dB or more

[General model] ....................................................................... 86 dB or more

Residual Noise (IHF-A Network)

MAIN L/R SP OUT..................................................................... 170 µV or less

Channel Separation (Vol. –30 dB)

CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX (Input 5.1 kΩ Shorted)

(EFFECT OFF) 1 kHz/10 kHz ....................................... 60 dB/45 dB or more

PHONO MM (Input Shorted) (EFFECT OFF)

1 kHz/10 kHz................................................................. 60 dB/55 dB or more

SPECIFICATIONS

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

VY77910 Printed in Japan

Transcripción de documentos

NATURAL SOUND AV AMPLIFIER CINEMA DSP 7ch DSP–A1092 VOLUME l6 VCR 2 VCR 1 20 DVD/LD l2 28 8 60 2 POWER VIDEO AUX TAPE (MD) TV/DBS TUNER PHONO CD 4 40 0 –dB l ON OFF 0 l 2 3 4 A PHONES SPEAKERS 4 5 B BASS TONE EXTENSION BYPASS l 2 3 5 0 l 2 l 2 3 3 4 4 5 5 0 SOURCE DVD/LD l 2 2 3 3 4 4 L5 5R TAPE (MD) TV/DBS TUNER VCR 1 CD VCR 2 PROGRAM VIDEO AUX SET MENU BASS TREBLE BALANCE Natural Sound AV Amplifire Amplificateur audiovisuel “Son Naturel” Natural Sound AV-Verstärker Natural Sound AV-förstärkare Amplificatore AV a suono naturale Amplificador AV de Sonido Natural Natural Sound AV Versterker EFFECT PHONO REC OUT DELAY/C/R /F/SWFR S VIDEO VIDEO L AUDIO R VIDEO AUX OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING Congratulations! You are the proud owner of a Yamaha Digital Sound Field Processing (DSP) System—an extremely sophisticated audio component. The DSP system takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and the DSP system will sonically transform your room into a wide range of listening environments—anything from a famous concert hall to a cozy jazz club. In addition, you get incredible realism from Dolby-Surround encoded video sources using the built-in Dolby Pro Logic Surround Decoder and Dolby Digital (AC-3) Decoder. Seven built-in channels of amplification on this model mean that no additional amplifiers are required to enjoy advanced digital sound field processing. Rather than tell you about the wonders of digital sound field processing, however, let’s get right down to the business of setting up the system and trying out its many capabilities. Please read this operation manual carefully and store it in a safe place for later reference. PRECAUTIONS & SAFETY INSTRUCTIONS Keep the unit away from locations where it is likely to be exposed to high temperatures or humidity—such as near radiators, stoves, etc. Also avoid locations which are subject to excessive dust accumulation or vibration which could cause mechanical damage. 2. INSTALL THE UNIT IN WELL-VENTILATED CONDITION The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in well-ventilated condition. Make sure to allow a space of at least 10 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit. Otherwise it may not only damage the unit, but also cause fire. 3. KEEP THE AC POWER PLUG DISCONNECTED DURING VACATION ETC. When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. 8. CLEAN WITH A SOFT DRY CLOTH For U.K. customers Never use solvents such as benzine or thinner to clean the unit. Wipe clean with a soft, dry cloth. If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. 9. USE THIS UNIT WITH THE CORRECT VOLTAGE The voltage to be used must be the same as that specified on this unit. Using this unit with a higher voltage than that which is specified is dangerous and may result in a fire or other type of accident causing damage. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified. 10.KEEP AWAY FROM TUNERS Digital signals generated by the unit may interfere with other equipment such as tuners, receivers or TVs. Move the system farther away from such equipment if interference is observed. IMPORTANT! Please record the model and serial number of your unit in the space below. Model: 4. AVOID PHYSICAL SHOCKS Strong physical shocks to the unit can cause damage. Handle it with care. 5. DO NOT OPEN THE UNIT OR ATTEMPT REPAIRS OR MODIFICATIONS YOURSELF This product contains no user-serviceable parts. Refer all maintenance to qualified Yamaha service personnel. Opening the unit and/or tampering with the internal circuitry will make servicing difficult and will endanger you and your unit. 6. MAKE SURE POWER IS OFF BEFORE MAKING OR REMOVING CONNECTIONS Always turn power OFF prior to connecting or disconnecting cables. This is important to prevent damage to the unit itself as well as other connected equipment. 7. HANDLE CABLES CAREFULLY Always plug and unplug cables—including the AC cord—by gripping the connector, not the cord. English 1. AVOID EXCESSIVE HEAT, HUMIDITY, DUST AND VIBRATION SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT The wires in the mains lead are coloured in accordance with the following code. Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off. Voltage Selector (General Model only) WARNING The voltage selector on the rear panel of this unit must be set for your local mains voltage BEFORE plugging into the AC mains supply. Voltages are 110/120/220/240 AC, 50/60 Hz. Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. VOLTAGE SELECTOR AC OUTLETS SWITCHED WARNING To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. I20W MAX. TOTAL IMPEDANCE SELECTOR A B CENTER C OR D: 4ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 4ΩMIN./ SPEAKER MAIN A OR B: 4ΩMIN./ SPEAKER A B: 8ΩMIN./ SPEAKER FRONT EFFECT: 6ΩMIN./ SPEAKER CENTER C OR D: 8ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 8ΩMIN./ SPEAKER MAIN A OR B: 8ΩMIN./ SPEAKER A B: 6ΩMIN./ SPEAKER FRONT EFFECT: 8ΩMIN./ SPEAKER IMPEDANCE SELECTOR (General model) 1 CONTENTS PRECAUTIONS & SAFETY INSTRUCTIONS ...................................1 GETTING STARTED ...........................................................................3 FEATURES ..........................................................................................5 SPEAKER SETUP.............................................................................10 CONTROLS & THEIR FUNCTIONS.................................................13 FRONT PANEL................................................................................13 DISPLAY PANEL .............................................................................16 CONNECTIONS.................................................................................17 REAR PANEL PARTS AND THEIR FUNCTIONS .........................17 REAR PANEL SWITCH AND CONTROL SETTINGS...................20 GENERAL INSTRUCTIONS FOR CONNECTIONS .....................20 CONNECTING AUDIO/VIDEO SOURCE EQUIPMENT TO THIS UNIT .................................................................................21 CONNECTING SPEAKER SYSTEMS...........................................25 SELECTING THE OUTPUT MODES SUITABLE FOR YOUR SPEAKER SYSTEM .......................................................................30 SPEAKER BALANCE ADJUSTMENT ............................................33 ADJUSTMENTS IN THE “SET MENU” MODE...............................35 GENERAL OPERATION ...................................................................38 PLAYING A SOURCE .....................................................................38 RECORDING A SOURCE TO AUDIO/VIDEO TAPE (OR DUBBING FROM A TAPE TO ANOTHER) ............................40 SELECTING SOUND FIELD PROGRAMS......................................42 CANCELING THE EFFECT SOUND .............................................43 DESCRIPTIONS OF THE SOUND FIELD PROGRAMS ..............44 ADJUSTING DELAY TIME AND EACH SPEAKER OUTPUT LEVEL..............................................................................................47 SETTING THE SLEEP TIMER..........................................................49 REMOTE CONTROL UNIT ...............................................................50 BASIC OPERATIONS (When the lid is open) ................................50 LEARNING NEW CONTROL FUNCTIONS (When the lid is open) .........................................................................................................52 USING OPERATION CONTROL KEYS (When the lid is closed) .........................................................................................................55 MACRO OPERATIONS (When the lid is closed) ...........................58 LEARNING A NEW FUNCTION.....................................................61 MAKING A NEW MACRO...............................................................63 CLEARING LEARNED FUNCTIONS.............................................64 TROUBLESHOOTING ......................................................................66 SPECIFICATIONS .............................................................................68 2 GETTING STARTED Installing the Remote Control Unit Batteries If you haven’t already done so, carefully remove this unit and its accessories from the box and wrapping material. You should find the unit itself and the following accessories. Since the remote control unit will be used for many of this unit’s control operations, you should begin by installing the supplied batteries. English Unpacking 1. Turn the remote control unit over and slide the battery compartment cover downward in the direction of the arrow. 2. Insert the batteries (LR6, AA, UM-3 type), being careful to align them with the polarity markings on the inside of the battery compartment. Batteries 3. Close the battery compartment cover. 2 1 Remote control 3 * User function stickers After you insert batteries (or you exchange batteries with new ones), press the RESET button before using the remote control unit. RESET button 3 Notes about the Remote Control Unit ● ● When you notice that remote control operation has become erratic, or the distance from which the remote control will function has decreased, it’s time to replace the batteries. Always replace all batteries at the same time. This remote control uses an advanced, highly directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit when operating. Open/close the control door When it is not necessary to operate controls inside the control door, close the door. To open the door Remote control transmitter operation range Remote control sensor To close the door Within approximately 6 m (19.7 feet) 30° 30 ° Notes ● There should be no large obstacles between the remote control unit and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control unit to work incorrectly. In this case, reposition the main unit to avoid direct lighting. 4 FEATURES In addition, this unit incorporates a Dolby Pro Logic Surround decoder and Dolby Digital (AC-3) decoder for multi-channel sound reproduction of Dolby Surround encoded video sources. The operation of the Dolby Pro Logic Surround or Dolby Digital (AC-3) decoder can be controlled by selecting a corresponding DSP program including combined operations of the Yamaha DSP and the Dolby Pro Logic Surround or Dolby Digital (AC-3) decoder. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing, the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert. What’s more, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of actual concert halls, jazz clubs, theaters, etc. from around the world, to allow you to accurately recreate any one of these live performance environments, all in your own home. English This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. This unit has a total of 10 digital sound field processor (DSP) modes. You can create an excellent audio sound field by selecting a suitable sound field (this will, of course, depend on what you will be listening to), and adding desired adjustments. 5 6 Dolby Pro Logic Surround Dolby Digital (AC-3) This unit employs a Dolby Pro Logic Surround decoder similar to professional Dolby Stereo decoders used in many movie theaters. By using the Dolby Pro Logic Surround decoder, you can experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic employs a four channel five speaker system. The Pro Logic Surround system divides the input signal into four levels: the left and right main channels, the center channel (used for dialog), and the rear surround sound channels (used for sound effects, background noise, and other ambient noises). The center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from the action on the screen while experiencing good stereo imaging. Dolby Surround is encoded on the sound track of pre-recorded video tapes, laser discs, and some TV/cable broadcasts. When you play a source encoded with Dolby Surround on this unit, the Dolby Pro Logic Surround decoder decodes the signal and distributes the surround-sound effects. The built-in Dolby Digital (AC-3) Decoder leads you into a totally new sound experiences. This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system improves the stability of sound at each channel and crosstalk between channels, so that positioning of sounds around the room is more accurate compared with conventional analog signal processing systems. Compared to Dolby Pro Logic that is referred to a “3/1” system (left front, center, right front and just one surround channel), Dolby Digital (AC-3) features two surround channels, called stereo or split surrounds, each offering the same full range fidelity as the three front channels. In addition, this unit features a built-in automatic input balance control. This always assures you the best performance without manual adjustment. Sound of wide dynamic range reproduced by the five full range channels presents listeners much excitement that has never been experienced before. Precise sound orientation by the discrete digital sound processing expands realism that the original movie possesses. Dolby Digital (AC-3) is a new generation of multi-channel digital audio technology, or the newest spatial sound processing format developed for 35 mm film-movies by employing a new kind of low bit-rate audio coding. Dolby Digital (AC-3) is a digital surround sound system that provides completely independent multi-channel audio to consumers. In multi-channel form, Dolby Digital (AC-3) provides five full range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), plus two surround channels. A sixth bass-only effect channel is also provided for output of LFE (low frequency effect), or low bass effects that are independent of other channels. This channel is counted as 0.1, thus giving rise to the term 5.1 channels in total. Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, “AC-3”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, Inc. All rights reserved. The following original functions make the surround-sound effect of Dolby Digital (AC-3) become the most suitable for your audio system and the listening conditions. Dolby Surround + DSP (CINEMA DSP) Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room is much different from those of a movie theater. English Laser Disc is a home audio format that could benefit from Dolby Digital (AC-3). In the near future, Dolby Digital (AC-3) will also be applied to DBS, CATV, DVD and HDTV. The ongoing release of Dolby Stereo Digital theatrical films now underway will provide an immediate source of Dolby Digital (AC-3) encoded video software. Yamaha DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for lack of presence and dynamics in your listening room with its original digital sound fields combined with Dolby Surround sound field. CINEMA DSP 7ch ● ● ● Dynamic range (sound scale) of source can be changed so that it will be suitable for the listening conditions. Output of low bass from any channel can be assigned to either the MAIN SPEAKERS terminals or SUBWOOFER terminals to maximize system performance. Output of LFE can be assigned to either the MAIN SPEAKERS terminals or SUBWOOFER terminals to maximize system performance. The YAMAHA “CINEMA DSP” logo indicates those programs are created by the combination of Dolby Surround and YAMAHA DSP technology. 7 Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital (AC-3) + 3 Digital Sound Fields Digital sound fields are created on the presence side and the rear surround side of the Dolby Pro Logic Surround-decoded sound field respectively. They create a wide acoustic environment and emphasize surround-effect in the room, letting you feel much presence as if you are watching a movie in a popular Dolby Stereo theater. Digital sound fields are created on the presence side and the independent left and right surround sides of the Dolby Digital (AC3)-decoded sound field respectively. They create a wide acoustic environment and much surround effect in the room without losing high channel separation. With wide dynamic range of Dolby Digital (AC-3) sound, this sound field combination lets you feel as if you are watching a movie in the newest Dolby Stereo Digital theater. This will be the most ideal home theater sound at the present time. This combination is available when the sound field program No. 2, No. 3 or No. 4 is selected, and the input signal of source is analog, PCM audio or encoded with the Dolby Digital (AC-3) in 2channels. 8 This combination is available when the sound field program No. 2, No. 3 or No. 4 is selected, and the input signal of source is encoded with the Dolby Digital (AC-3) (except in 2-channels). If you connect your video cassette recorder, LD player, video monitor, etc. to this unit, you can take advantage of this unit’s capability to display program titles and information for various setting changes and adjustments on your video monitor’s screen. This information will be superimposed over the video image. English Video superimpose If there is no video source connected or it is turned off, the information will be displayed over a blue colored background. TEST DSP EFFECT LEVEL / FRONT 0dB NOTE: The program titles and other information are also displayed on the display panel of this unit. SPEAKERS A DSP 9 SPEAKER SETUP Setting Up Your Speaker System Use of the Center Dialog Speaker Is Recommended This unit has been designed to provide the best sound field quality with a full seven-speaker system setup, using two extra pairs of effect speakers to generate the sound field plus one center speaker for dialog. We therefore recommend that you use a sevenspeaker setup. A four-speaker system using only one pair of effect speakers for the sound field will still provide impressive ambience and effects, however, and may be a good way to begin with this unit. You can always upgrade to the full seven speaker system later. In the 4 or 5 speaker system, the Digital Sound Field Processing is still performed, but the main speakers are used for both the main channels and the front effect channels. When playing back a source with the DSP programs No. 1 through No. 4, or when the Dolby Digital (AC-3) is decoded with any DSP program used, if the source contains center-channel signals, dialog, vocals etc. are output from the center channel. Therefore, if you want to maximize the performance of your Audio/Video home theater system, it is recommended that you use a center channel speaker. If for some reason it is not practical to use a center speaker, it is possible to enjoy movie viewing without it. Best results, however, are obtained with the full system. Use of a Subwoofer Expands Your Sound Field It is also possible to further expand your system with the addition of a subwoofer and amplifier. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low frequency effect) sound with high fidelity when playing back a source with the Dolby Digital (AC-3) decoded. You may wish to choose the convenience of a Yamaha Active Servo Processing Subwoofer System, which has its own built-in power amplifier. 10 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Simplest system. Good for Audio/Video sources. Good for sound fields from 2channel stereo sources. This is the recommended speaker system, providing the best sound effects. You can enjoy widely diffused sound by only adding two additional speaker units at the rear. By the use of center speaker, center sounds (dialog, vocals etc.) are precisely localized. When a normal stereo source is played back with the sound field programs No. 5 through No. 10, a sound effect matching that of a 7speaker system can be obtained. The addition of front left and right effect speakers produces a more effective sound field. When a normal stereo source is played back with the sound field programs No. 5 through No. 10, using both sets of effect speakers (front and rear), reproduces the most effective sound field. When using the sound field programs No. 1 through No. 4 or when using any program with the Dolby Digital (AC-3) decoded, the center speaker provides precise center localization. FRONT MIX switch—Set to ON. (See page 20.) CENTER SPEAKER—Set to PHNTM. (See page 30.) FRONT MIX switch—Set to ON. (See page 20.) CENTER SPEAKER—Set to NRML or WIDE. (See page 30.) FRONT MIX switch—Set to OFF. (See page 20.) CENTER SPEAKER—Set to PHNTM. (See page 30.) FRONT MIX switch—Set to OFF. (See page 20.) CENTER SPEAKER—Set to NRML or WIDE. (See page 30.) English Four Possible Types of Speaker System Configurations Recommended 11 Speakers and Speaker Placement Your full seven-speaker system will require three speaker pairs: the MAIN SPEAKERS (your normal stereo speakers), the FRONT EFFECT SPEAKERS and the REAR SPEAKERS, plus the CENTER SPEAKER. You may also be using a subwoofer. The MAIN SPEAKERS should be high performance models and have enough power handling capacity to accept the maximum output of your audio system. Other speakers do not have to be equal to the MAIN SPEAKERS. For precise sound localization, however, it is ideal to use high performance models that can reproduce sounds in full range for the CENTER SPEAKER and the FRONT EFFECT and REAR SPEAKERS. Place the MAIN SPEAKERS in the normal position. Place the FRONT EFFECT SPEAKERS further apart than the MAIN SPEAKERS, on either side of and a few feet behind and above the MAIN SPEAKER pair. Main speaker Place the REAR SPEAKERS behind your listening position. They should be nearly six feet up from the floor. Subwoofer Place the CENTER SPEAKER precisely between the two MAIN SPEAKERS. (To avoid interference, keep the speaker above or below the television monitor, or use a magnetically shielded speaker.) If using a SUBWOOFER, such as a Yamaha Active Servo Subwoofer System, the position of the speaker is not so critical because low bass tones are not highly directional. 12 Front effect speaker Rear speaker Center speaker CONTROLS & THEIR FUNCTIONS English FRONT PANEL 1 2 3 4 5 6 (Europe Model) NATURAL SOUND AV AMPLIFIER CINEMA DSP 7ch DSP–A1092 VOLUME l6 VCR 2 VCR 1 20 DVD/LD l2 28 8 POWER VIDEO AUX TAPE (MD) TV/DBS TUNER PHONO CD 4 40 2 60 0 –dB l ON OFF 0 l 2 3 4 A PHONES 7 * SPEAKERS 8 BASS TONE EXTENSION BYPASS 9 0 0 l 2 3 4 5 l 2 3 4 5 B l 2 3 DVD/LD l 2 5R TUNER VCR 1 PROGRAM CD VCR 2 4 L5 5 TAPE (MD) TV/DBS 3 4 4 5 SOURCE 0 2 3 VIDEO AUX SET MENU BASS TREBLE A BALANCE B EFFECT PHONO S VIDEO DELAY/C/R /F/SWFR C DE F VIDEO L AUDIO R VIDEO AUX REC OUT G H I J For control keys on the remote control unit, see pages 50 to 52. 13 1 POWER Switch Turns this unit on and off. * When you press this switch to turn the power on, you will hear a click and a sound of the built-in fan rotating for a moment. 2 Standby Indicator While the power of this unit is on, pressing the (SYSTEM POWER) OFF key on the remote control unit switches this unit to the standby mode. In this mode, the standby indicator is illuminated. 3 Remote Control Sensor Signals from the remote control unit are received here. 4 Display Panel See page 16. 5 Input Selector Buttons Selects an input source that you want to listen to (and watch). 6 Master VOLUME Control Simultaneously controls volume level at all outputs: front effect, main, rear effect, center, and subwoofer. (This does not affect REC OUT level.) * When the volume is decreased by pressing the MUTE key on the remote control unit, the indicator on the master VOLUME control flashes on and off. 7 PHONES Jack When you listen with headphones, connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through headphones. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position and switch off the digital sound field processor (so that no DSP program name is illuminated on the display panel) by pressing the EFFECT switch. 14 8 SPEAKERS switches Set the switch A or B (or both A and B) for the main speakers (connected to this unit) you will use to the ON position. Set the switch for the main speakers you will not use to the OFF position. Selected main speakers are shown by the lighting of “SPEAKERS A” and/or “SPEAKERS B” on the display panel. 9 BASS EXTENSION Switch When pressed inward (ON), boosts bass frequency response at the main left and right channels while maintaining overall tonal balance. If you do not have a subwoofer, the use of this switch will be effective to reinforce the bass frequencies. 0 TONE BYPASS switch When this switch is pressed inward (ON), the input signal does not pass through the tone (BASS and TREBLE) control circuitry so that it is unaffected by the tone control circuitry. Use this switch to obtain pure sound and to check the tone control setting. Press this switch to release it outward (OFF) to use the tone control circuitry. A BASS and TREBLE Controls Adjust low and high frequency response respectively for the main channels only. B BALANCE Control Adjusts the left and right output volume to the Main Speakers to compensate for sound imbalance caused by speaker positions or listening room conditions. C REC OUT Selector Selects the source to be recorded to a tape deck or VCR independently of the setting of the input selector buttons. However, when set to the SOURCE position, the setting of the input selector buttons decides the source to be recorded to a tape deck or VCR. Sequentially selects the digital sound field processing programs in the + or – direction. E SET MENU Switch Whenever pressed, selects functions in the SET MENU mode. F DELAY/C/R/F/SWFR Switch Whenever pressed, selects the item of changing delay time, center speaker output level, rear speaker output level, front effect speaker output level and subwoofer output level in turn. * Depending on a mode of this unit, the number of selections is reduced. For example, when the built-in digital sound field processor (including the Dolby Pro Logic Decoder or the Dolby Digital (AC-3) Decoder) is off, only the item for changing subwoofer output level can be selected. G –/+ Button Adjusts the level of item selected by pressing the DELAY/C/R/F/SWFR switch. Moreover, performs setting changes and adjustments for functions selected by pressing the SET MENU switch. H EFFECT Switch Normally ON, this switch can be turned OFF to disable output from the center and effect speakers so that the sound becomes normal 2-channels. * Even if this switch is off, when the Dolby Digital (AC-3) is decoded, signals at all channels are distributed to the main channels and output from the main speakers. English D PROGRAM Selector I Auxiliary Input Jacks (VIDEO AUX) Connect an auxiliary video or audio unit such as a camcorder to these jacks. If the connected video unit has a S video output terminal, connect it to the S VIDEO jack to obtain a high resolution picture. The unit connected to these jacks can be selected by the corresponding input selector button and REC OUT selector. J Control Door See page 4 for how to open and close the control door. 15 DISPLAY PANEL 1 2 DIGITAL ENHANCED 70 mm mS dB SPEAKERS SPEAKERS A B PCM 3 1 Input Source Display Shows the currently selected input source. 2 Multi-informatiom Display Shows the currently selected DSP program, or information for several adjustments or setting changes made on this unit. 3 SPEAKERS A/B Indicators The indicator A or B which corresponds to the currently selected main speakers lights up. If both main speakers A or B are selected, both indicators light up. 4 Digital Audio Input Signal Indicators When digital audio signals not encoded with the Dolby Digital (AC-3) are input to this unit, “PCM DIGITAL” lights up. When digital audio signals encoded with the Dolby Digital (AC-3) are input to this unit, “ DIGITAL” lights up. 16 DIGITAL DIGITAL 4 5 DSP 5 PRO LOGIC SLEEP 6 DIGITAL, DSP and PRO LOGIC indicators “ DIGITAL” lights up when the built-in Dolby Digital (AC-3) Decoder is on and the signals of selected source encoded with the Dolby Digital (AC-3) is not in 2-channels. “DSP” lights up when the built-in digital sound field processor is on, and “ PRO LOGIC” lights up when the built-in Dolby Pro Logic Surround Decoder is on. Depending on the selected DSP program, both “ DIGITAL” and “DSP”, or both “DSP” and “ PRO LOGIC” will light up. 6 SLEEP Indicator Lights up while the built-in SLEEP timer is functioning. CONNECTIONS English REAR PANEL PARTS AND THEIR FUNCTIONS Before you start making connections make sure all related electronic components are turned OFF. 1 2 3 4 5 6 7 8 9 (General Model) AUDIO SIGNAL PCM/ DIGITAL IN COAXIAL DVD/LD TV/DBS TV/DBS IN IN VCR 1 VCR 1 OUT OUT 4 IN IN VCR 2 VCR 2 C D C OR D C D OUT MONITOR OUT PAL NTSC A I00W MAX. TOTAL REAR CAUTION OUT To AC outlet AC OUTLETS SWITCHED CENTER GND 0 VOLTAGE SELECTOR FRONT EFFECT 3 REC OUT (AC-3 DIGITAL IN) DVD/LD D TAPE PB TAPE(MD) OPTICAL SPEAKERS CENTER 2 TUNER TV/DBS OUTPUT 1 CD OPTICAL COAXIAL VIDEO SIGNAL S VIDEO VIDEO C PHONO DVD/LD AUDIO SIGNAL SEE INSTRUCTION MANUAL FOR CORRECT SETTING. A COUPLER MAIN CH PRE MAIN OUT IN MAIN IMPEDANCE SELECTOR A CENTER C OR D: 4ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 4ΩMIN./ SPEAKER MAIN A OR B: 4ΩMIN./ SPEAKER A B: 8ΩMIN./ SPEAKER FRONT EFFECT: 6ΩMIN./ SPEAKER OUTPUT SUB WOOFER FRONT EFFECT REAR B MONITOR OUT B CENTER C OR D: 8ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 8ΩMIN./ SPEAKER MAIN A OR B: 8ΩMIN./ SPEAKER A B: 6ΩMIN./ SPEAKER FRONT EFFECT: 8ΩMIN./ SPEAKER ON OFF —I0dB 0dB 5ch 7ch FRONT MAIN MIX LEVEL B C D EF GH I J K 17 1 PCM/ DIGITAL IN (COAXIAL and OPTICAL) jacks Can be connected with audio/video units that have a coaxial or optical digital output jack. Connect a unit that is connected to the DVD/LD AUDIO/VIDEO SIGNAL connection jacks to the DVD/LD COAXIAL or OPTICAL jack. Connect a unit that is connected to the TV/DBS AUDIO/VIDEO SIGNAL connection jacks to the TV/DBS COAXIAL or OPTICAL jack. * If, for example, your LD player has an AC-3 RF output jack and no digital output jack for AC-3 discrete audio signals, connect the AC-3 RF output jack to the DVD/LD COAXIAL or OPTICAL jack of this unit by way of an RF demodulator (separate purchase). 2 AUDIO SIGNAL Connection Jacks (for Audio Source Equipment) Connect the inputs and/or outputs of your audio equipment. 3 AUDIO/VIDEO SIGNAL Connection Jacks (for Video Source Equipment) Connect the audio and video inputs and/or outputs of your video equipment. In place of the VIDEO jacks, the S VIDEO jacks can be used for higher resolution and improved picture quality if your VCR, monitor, etc. are equipped with S-VIDEO connectors. 4 CENTER OUTPUT Jacks Center-channel line outputs. Can be connected to input jack(s) of one or two external power amplifier(s) to drive the center speaker(s). 5 CENTER SPEAKERS Terminals When using the built-in center-channel amplifier, connect one or two center speakers here. 18 6 Center Speaker Switch Set to “C + D” when using two center speakers, or to “C OR D” when using only one center speaker. 7 FRONT EFFECT SPEAKERS Terminals When using the built-in front effect-channel amplifier, connect the front effect speakers here. 8 REAR SPEAKERS Terminals When using the built-in rear-channel amplifier, connect the rear speakers here. 9 VOLTAGE SELECTOR (General Model only) Be sure to set to the line voltage in your area before applying power. Consult your dealer if unsure of the correct setting. 0 GND Terminal Connects the ground wire of the turntable to produce minimum hum. In some cases, however, better results may be obtained with the ground wire disconnected. A Video NTSC/PAL Switch (General Model only) Set this switch to the position corresponding to the standard that your video equipment employs. B FRONT MIX Switch Set to “OFF (7ch)” when setting up a full 7 or 6 speaker system, or to “ON (5ch)” when setting up a 5 or 4 speaker system. C MAIN LEVEL Switch Normally set to “0 dB”. If desired, you can decrease the mainchannel output level at the MAIN SPEAKERS terminals by 10 dB by setting this switch to “–10 dB”. Main-channel line output. Connected with jumper bars to MAIN IN jacks when the built-in amplifier is used. Connected to input jacks of external stereo power amplifier (MAIN IN or TAPE PLAY jacks of integrated amplifier or receiver) when using external amplification. E MAIN IN Jacks Line input to built-in main-channel amplifier. Connected with jumper bars to PRE OUT jacks when the built-in amplifier is used. Not connected when using an external power amplifier. F SUBWOOFER Jacks When using one subwoofer, connect its amplifier input to either of these jacks. When using two subwoofers, connect their amplifiers to these jacks respectively. Frequencies below 90 Hz distributed from the main, center and/or rear channels are output to these jacks. Signals of LFE (low frequency effect) generated when the Dolby Digital (AC-3) is decoded are also output if they are assigned to these jacks. H REAR OUTPUT Jacks Rear-channel line output. Can be connected to input jacks of an external stereo power amplifier driving the rear speakers. English D PRE OUT Jacks I MAIN SPEAKERS Terminals This unit is equipped with 2 sets of MAIN SPEAKERS terminals to allow you to connect 2 main speaker systems to this unit. When using this unit’s built-in main-channel amplifier, connect the main speakers here. The jumper bars must be plugged in to connect the MAIN IN jacks to the PRE OUT jacks. J IMPEDANCE SELECTOR Switch Select the position whose requirements your speaker system meets. K SWITCHED AC OUTLET(S) You may plug other audio/video units into these sockets as long as their combined power consumption does not exceed the specified value shown. “Switched” means that these components are turned on and off by this unit’s power switch. G FRONT EFFECT OUTPUT Jacks Front-channel line output. Can be connected to input jacks of an external stereo power amplifier driving the front effect speakers. 19 REAR PANEL SWITCH AND CONTROL SETTINGS GENERAL INSTRUCTIONS FOR CONNECTIONS There are several switches and controls on the rear panel that you’ll have to check before operating your system, and it’s a good idea to do it before you connect cables. Locate the MAIN LEVEL slide switch (C) and FRONT MIX slide switch (B). Make sure the MAIN LEVEL switch is set to “0 dB” and the FRONT MIX switch is set to “OFF” for 7 or 6 speaker driving. Make sure that you have the left (L) and right (R) channels correctly connected. That means that jacks marked “L” on this unit must be connected to jacks marked “L” on other units. Likewise with the “R” jacks. This is easy if you remember to always use the red plug for the “R” jacks and the white plug for the “L” jacks. In a 5 or 4 speaker system, set the FRONT MIX switch to “ON”. For connections with audio/video source equipment, use RCA type pin plug cables with the exception described later. Next, set the NTSC/PAL switch (A) to the position corresponding to the standard which your video equipment employs. (General Model only) For the setting of IMPEDANCE SELECTOR switch (J), see page 29. For the setting of the center speaker switch (6), see page 27. 20 With speaker connections you must also be sure that the polarity is correct. For each amplifier and each channel, connect the plus (+) terminal of the amplifier to the plus terminal of the speaker, and connect the minus (–) terminal of the amplifier to the minus terminal of the speaker. To keep track of polarity, use a speaker cable that has one of the two wires marked by a stripe or a different color. English CONNECTING AUDIO/VIDEO SOURCE EQUIPMENT TO THIS UNIT BASIC CONNECTIONS * If you have YAMAHA audio/video unit numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure to connect the output (or input) terminals of each unit to the same-numbered terminals of this unit. AUDIO OUT VIDEO OUT LD (DVD) player AUDIO SIGNAL PCM/ DIGITAL IN COAXIAL PHONO DVD/LD OPTICAL COAXIAL CD player OPTICAL Tuner DVD/LD TV/DBS TV/DBS IN IN VCR 1 VCR 1 OUT OUT 3 TAPE PB TAPE(MD) 4 REC OUT OUTPUT DVD/LD IN IN VCR 2 VCR 2 OUT OUT GND MONITOR OUT MONITOR OUT LINE OUT LINE IN Tape deck (MD recorder) AUDIO OUT VIDEO OUT 2 TUNER TV/DBS VIDEO SIGNAL S VIDEO VIDEO 1 CD OUTPUT AUDIO SIGNAL PAL NTSC AUDIO OUT VIDEO OUT AUDIO IN VIDEO IN TV/Satellite tuner AUDIO OUT VIDEO OUT AUDIO IN VIDEO IN Video cassette recorder 2 ON OFF —I0dB 0dB 5ch 7ch FRONT MAIN MIX LEVEL GND Video cassette recorder 1 VIDEO IN OUTPUT Monitor TV Turntable * For shaded parts, see pages 22 to 24. 21 CONNECTING TO DIGITAL (OPTICAL AND COAXIAL) JACKS If your LD (DVD) player, TV/satellite tuner, etc. are equipped with coaxial or optical digital audio signal output jacks, they can be connected to this unit’s COAXIAL and/or OPTICAL digital signal input jacks. LD (DVD) player ANALOG OUT OPTICAL DIGITAL OUT COAXIAL DIGITAL OUT Even if you connect an audio/video unit to the OPTICAL (or COAXIAL) jack of this unit, you must keep the unit connected with the same named analog audio signal jacks of this unit, because digital signal cannot be recorded by a tape deck or VCR connected to this unit. You can switch the selection of input signals between “digital” and “analog” easily. (See page 39 for details.) AUDIO SIGNAL PCM/ DIGITAL IN COAXIAL To make a connection between optical digital audio signal jacks, remove the cover from each jack, and then connect them by using a commercially available optical fiber cable that conforms to EIAJ standards. Other cables might not function correctly. AUDIO SIGNAL PHONO DVD/LD 1 CD COAXIAL DIGITAL OUT OPTICAL DIGITAL OUT OPTICAL COAXIAL TV/DBS 2 TUNER IN VCR 1 TV/DBS 3 TAPE PB TAPE(MD) OPTICAL TV/Satellite tuner DVD/LD 4 REC OUT ANALOG OUT OUT IN VCR 2 OUT GND MONITOR OUT PAL NTSC NOTE: When connecting an audio/video unit to both of the digital and analog jacks of this unit, make sure to connect to both jacks of the same name. NOTE: Be sure to attach the covers when the OPTICAL jacks are not being used, in order to protect the jacks from dust. 22 NOTE: All digital audio signal input jacks are applicable to the sampling frequency of 32 kHz, 44.1 kHz and 48 kHz. If your LD player has AC-3 RF signal output jack and no digital signal output jack for AC-3 discrete audio signals, connect the AC3 RF signal output jack to this unit’s OPTICAL (or COAXIAL) digital signal input jack by using an RF demodulator (separate purchase). First, connect the AC-3 RF signal output jack of the LD player to the AC-3 RF signal input jack of the RF demodulator. Next, connect the optical (or coaxial) digital signal output jack of the RF demodulator to the OPTICAL (or COAXIAL) digital signal input jack of this unit. This connection is necessary for inputting audio signals encoded with the Dolby Digital (AC-3) on the LD player to this unit. It is also necessary to connect the LD player to this unit’s analog audio signal input jacks regardless of the AC-3 RF signal connection, for playing back an LD source with the Dolby Pro Logic Surround decoded or in normal stereo (or monaural). If desired, you can also connect the digital signal output jack (for 2-channel audio signals) of the LD player to this unit. If you will do so, connect it to the COAXIAL digital signal input jack of this unit, and connect the RF demodulator to the OPTICAL digital signal input jack of this unit. By this connection, if the input mode of the DVD/LD source is in “AUTO”, you can enjoy listening to sounds decoded with the Dolby Digital (AC-3) when you play a disc encoded with the Dolby Digital (AC-3) though signals are input to both OPTICAL and COAXIAL digital signal input jacks of this unit simultaneously (because signals input to the OPTICAL jack take priority of signals input to the COAXIAL jack). See page 39 for details about switching the input mode. NOTES ● If, for example, you play a CD on the LD player (which can play a CD also), there is no input to the OPTICAL jack, so the signals input to the COAXIAL jack take priority. In this case, switch off the RF demodulator to listen to CD sound surely. However, if your RF demodulator is the Yamaha model APD-1, you do not have to switch it off. ● When you want to play a source encoded with the Dolby Digital (AC-3) without decoding the Dolby Digital (AC-3), you must switch off the power to the RF demodulator. English Notes on connecting with an LD player equipped with an AC-3 RF output LD player ANALOG OUT AC-3 RF OUT AC-3 RF IN COAXIAL DIGITAL OUT COAXIAL DIGITAL OUT OPTICAL DIGITAL OUT RF demodulator (YAMAHA APD-1 etc.) AUDIO SIGNAL PCM/ DIGITAL IN COAXIAL PHONO DVD/LD DVD/LD 1 CD OPTICAL COAXIAL AUDIO SIGNAL TV/DBS 2 TUNER IN VCR 1 TV/DBS 3 TAPE PB TAPE(MD) OPTICAL 4 REC OUT OUT IN VCR 2 OUT GND MONITOR OUT 23 CONNECTING TO S VIDEO JACKS LD (DVD) player VIDEO OUT S-VIDEO OUT Video cassette recorder 1 TV/Satellite tuner DVD/LD DVD/LD TV/DBS TV/DBS S-VIDEO OUT OUT OUT IN IN VCR 2 VCR 2 OUT OUT MONITOR OUT MONITOR OUT 24 PAL NTSC VIDEO IN Notes about the Video superimpose ● If you watch a video source that is connected to both S VIDEO and VIDEO input jacks of this unit, signals of screen display information are output from only the S VIDEO MONITOR OUT jack. ● When no video signal is input to either S VIDEO or VIDEO input jacks of this unit, signals of screen display information are output from both S VIDEO MONITOR OUT and VIDEO MONITOR OUT jacks with a color background. * For the General Model, if the NTSC/PAL switch on the rear panel is set to “PAL”, nothing will be output from either S VIDEO MONITOR OUT or VIDEO MONITOR OUT jack in this case. S-VIDEO OUT IN VCR 1 VIDEO OUT VIDEO OUT IN VCR 1 S-VIDEO IN S-VIDEO OUT VIDEO OUT VIDEO SIGNAL S VIDEO VIDEO VIDEO IN NOTE: If your unit is the General Model, be sure the NTSC/PAL switch has been correctly set to the standard that your video equipment employs. Other models have no switch and use the PAL standard. VIDEO IN NOTE: If video signals are sent to both S VIDEO input and VIDEO input jacks, the signals will be sent to their respective output jacks independently. S-VIDEO IN AUDIO SIGNAL S-VIDEO IN If your video cassette recorder, LD player, etc. and your monitor are equipped with “S” (high-resolution) video terminals, connect them to this unit’s S VIDEO jacks, and connect this unit’s S VIDEO MONITOR OUT jack to the “S” video input of your monitor. Otherwise, connect the composite video jacks from your video cassette recorder, LD player, etc. to the VIDEO jacks of this unit, and connect this unit’s VIDEO MONITOR OUT jack to the composite video input of your monitor. Monitor TV Video cassette recorder 2 Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other or any other metal part as this could damage this unit and/or speakers. Make a connection as figured below with a commercially available scart-plug connector cable. IN IN VCR 2 VCR 2 OUT OUT CONNECTING SPEAKER SYSTEMS NOTE: Use speakers with the specified impedance shown on the rear of this unit. MONITOR OUT MONITOR OUT Red: positive (+) Black: negative (–) No connection PAL NTSC Scart-plug connector cable AUDIO R AUDIO L VIDEO 2 Monitor TV English For connecting with a monitor TV that uses a 21 pin connector for input (for Europe and U.K. models) 1 3 ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire. NOTE: Banana Plug connections are also possible (Australia and General models only). Simply insert the Banana Plug connector into the corresponding terminal. 25 CONNECTING THE MAIN SPEAKERS TO THIS UNIT One or two sets of MAIN speakers can be connected to this unit. Main speaker A If you use two sets of MAIN speakers, connect one set to the MAIN SPEAKERS A terminals, and connect another set to the B terminals. If you use only one set of MAIN speakers, connect them to either the MAIN SPEAKERS A or B terminals. Make sure that the jumper bars between the PRE OUT and MAIN IN jacks on the rear panel are in place. Power amplifier INPUT It is also possible to use an external power amplifier if more power is desired. In this case, remove the jumper bars and connect the PRE OUT jacks to the INPUT jacks of a stereo power amplifier with a stereo pin cable—making sure to connect the left and right channels correctly. Connect the MAIN speakers to the speaker output terminals of the power amplifier. PRE OUT This unit Set the SPEAKERS switch A or B (or both A and B) on the front panel corresponding to the main speakers you will use to the ON position. Set the switch for the main speakers you will not use to the OFF position. Selected main speakers are shown by the lighting of “SPEAKERS A” and/or “SPEAKERS B” on the display panel. Main speaker B 26 Main speaker A Main speaker B Connect the FRONT effect speakers to the FRONT EFFECT SPEAKERS terminals of this unit. If the FRONT effect speakers are not used, the FRONT MIX switch should be set to “ON”. Front effect speaker L Front effect speaker Center speaker Center speaker Center speaker English CONNECTING THE FRONT EFFECT SPEAKERS, REAR SPEAKERS AND THE CENTER SPEAKER(S) TO THIS UNIT R Connect the REAR speakers to the REAR SPEAKERS terminals of this unit. Connect the CENTER speaker to the CENTER SPEAKERS terminals. If you will be using one CENTER speaker, connect it to either the C or D terminals and set the CENTER speaker switch so that it is released outward (“C OR D” position). If using two CENTER speakers, connect them to the C and D terminals, and press the switch inward (“C+D” position). If, however, you will not be using a CENTER speaker, be sure to set the CENTER SPEAKER mode to “PHNTM” (phantom). (See page 30.) This unit NOTE: The speaker connections above are fine for most applications. If for some reason, however, you wish to use an external power amp for any or all of the front effect, rear and center channels, connect the line level output jack(s) for each channel to the INPUT jacks of the external amp and connect the corresponding speaker pair to the speaker terminals of the external amp. L Rear speaker R Rear speaker 27 ADDING A SUBWOOFER You may wish to add a subwoofer to reinforce the bass frequencies. This unit provides line-level subwoofer outputs. If you use one subwoofer, connect either of the SUBWOOFER jacks to the INPUT jack of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. If you wish to obtain more presence in your listening room, the use of two subwoofers is recommended. To connect two subwoofers to this unit, connect one SUBWOOFER jack to the INPUT jack of the amplifier driving a subwoofer, and the other SUBWOOFER jack to the INPUT jack of the amplifier driving the other subwoofer, and then connect each subwoofer to the corresponding amplifier. COUPLER MAIN CH PRE MAIN OUT IN COUPLER MAIN CH PRE MAIN OUT IN OUTPUT SUB WOOFER FRONT EFFECT REAR OUTPUT SUB WOOFER FRONT EFFECT REAR Subwoofer system Subwoofer system Subwoofer system With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. 28 IMPEDANCE SELECTOR Select the position whose requirements your speaker system meets. Be sure to switch this only when the power of this unit is turned off. English Switching the IMPEDANCE SELECTOR switch on the rear panel CENTER C OR D: 4ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 4ΩMIN./ SPEAKER MAIN A OR B: 4ΩMIN./ SPEAKER A B: 8ΩMIN./ SPEAKER FRONT EFFECT: 6ΩMIN./ SPEAKER CENTER C OR D: 8ΩMIN./ SPEAKER SET SPEAKER MODE C D: 4ΩMIN./ SPEAKER SET SPEAKER MODE REAR 8ΩMIN./ SPEAKER MAIN A OR B: 8ΩMIN./ SPEAKER A B: 6ΩMIN./ SPEAKER FRONT EFFECT: 8ΩMIN./ SPEAKER WARNING Never switch the setting of this switch when the power of this unit is on, otherwise this unit will break down. (Europe model) (Lower position) (Upper position) Center: If you use one center speaker, the impedance of the speaker must be 4Ω or higher. If you use two center speakers, the impedance of each speaker must be 4Ω or higher. Rear: The impedance of each speaker must be 4Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be 4Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher. Front effect: The impedance of each speaker must be 6Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be 8Ω or higher. If you use two center speakers, the impedance of each speaker must be 4Ω or higher. Rear: The impedance of each speaker must be 8Ω or higher. Main: If you use one pair of main speakers, the impedance of each speaker must be 8Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. Front effect: The impedance of each speaker must be 8Ω or higher. 29 SELECTING THE OUTPUT MODES SUITABLE FOR YOUR SPEAKER SYSTEM This unit provides you the following four functions to determine the method of distributing output signals to speakers suitable for your audio system. When speaker connections are all completed, select a proper position on each function to make the best use of your speaker system. 4. CENTER SPEAKER 5. REAR SPEAKER 6. MAIN SPEAKER 7. LFE/BASS OUT DESCRIPTION OF EACH FUNCTION 4. CENTER SPEAKER 5. REAR SPEAKER Choices: NRML/WIDE/PHNTM Preset position: NRML Choices: SMALL/LARGE Preset position: SMALL NRML (Normal): Select this position when you use a center speaker that is smaller than the main speakers. In this position, low bass signals (below 90 Hz) at the center channel are output from the main speakers (or the SUBWOOFER jacks if the SMALL position is selected on “6. MAIN SPEAKER” and the SWFR position is selected on “7. LFE/BASS OUT”). WIDE: Select this position when your center speaker is approximately the same size as the main speakers. PHNTM (Phantom): Select this position when you do not have a center speaker. The center channel sound will be output from the left and right main speakers. 30 SMALL: Select this position if your rear speakers do not have a high ability for bass reproduction. In this position, low bass signals (below 90 Hz) at the rear channels are output from the SUBWOOFER jacks (or the main speakers if the MAIN position is selected on “7. LFE/BASS OUT”). LARGE: Select this position if your rear speakers have a high ability for bass reproduction, or a subwoofer is connected to the rear speaker in parallel. In this position, full range signals are output from the rear speakers. 7. LFE/BASS OUT Choices: SMALL/LARGE Preset position: LARGE Choices: MAIN/SWFR/BOTH Preset position: SWFR SMALL: Select this position if your main speakers do not have a high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) at the main channels are output from the SUBWOOFER jacks (if the SWFR or BOTH position is selected on “7. LFE/BASS OUT”). LARGE: Select this position if your main speakers have a high ability for bass reproduction. In this position, full range signals present at the main channels are output from the main speakers. English 6. MAIN SPEAKER MAIN: Select this position if your system does not include a subwoofer. In this position, full range signals present at the main channels, signals from the LFE channel and other low bass signals that are selected on “4. CENTER SPEAKER” to “6. MAIN SPEAKER” to be distributed from other channels are output from the main speakers. SWFR/BOTH: Select either the SWFR or BOTH position if your system includes a subwoofer. In either position, signals at LFE channel and other low bass signals that are selected on “4. CENTER SPEAKER” to “6. MAIN SPEAKER” to be distributed from other channels are output from the SUBWOOFER jacks. When the LARGE position is selected on “6. MAIN SPEAKER”, in the SWFR position, no signal is distributed from the main channels to the SUBWOOFER jacks, however in the BOTH position, low bass signals from the main channels are output to both of the main speakers and the SUBWOOFER jacks. 31 METHOD OF CHANGING SELECTIONS Operations should be made watching information on this unit’s display panel or the monitor screen. 3. Press “+” or “–” once or more so that the arrow points the position you will select. Remote control Front panel 1. Turn the power of this unit on. (If you want to display information on the monitor, turn the power of the monitor on.) or Front panel 4. Press once or more until the title of another function on which you will change the selection appears on the display. POWER Remote control Front panel If you will use the remote control unit, set the TIME/LEVEL·SET MENU switch to the SET MENU position on the remote control unit. NOTE: Be sure to use the remote control unit with the lid open. SET MENU or Remote control 5. Press “+” or “–” once or more so that the arrow points the position you will select. TIME/LEVEL 2. Press once or more until “4. CENTER SPEAKER” appears on the display. 32 or Remote control Front panel SET MENU Remote control Front panel SET MENU or 6. Repeat step 4 and 5 to change selections on other functions in the same way. SPEAKER BALANCE ADJUSTMENT 3. Press the adjust. or key to select the speaker whose level you will Remote control The adjustment of each speaker output level should be done at your listening position with the remote control unit. Otherwise, the result may not be satisfactory. NOTE: Be sure to use the remote control unit with the lid open. 1. Set the TIME/LEVEL·SET MENU switch on the remote control to the TIME/LEVEL position. Remote control English This operation uses an internal test-tone generator for balancing the levels of the main, center, rear and front effect speakers. * Whenever the key is pressed, the speaker selection changes in turn as follows. Center Right rear CENTER R SUR. TIME/LEVEL SET MENU 2. Depress the TEST key on the remote Remote control control so that “TEST DOLBY SUR.” appears on the display panel to enter test mode. A TEST hiss-like calibration signal should be heard from the left main speaker, center speaker(s), right main speaker, right rear speaker and left rear speaker in turn (see diagram). Adjust the master VOLUME to a normal listening level. * The state of test-tone output is shown on the display panel and the monitor screen. (On the monitor screen, it is shown by an image of audio listening room.) This is convenient for adjusting each speaker level. Left main Center Right main LEFT CENTER RIGHT Left rear Right rear LEFT SURROUND RIGHT SURROUND L SUR. Left rear Pressing the key changes the speaker in the reverse order. * If the CENTER SPEAKER mode is set to “PHNTM” (phantom), “CENTER” cannot be selected. (See page 30.) 4. Adjust the level of the speaker selected in step 3 by pressing the + or – key so that it becomes almost as same as that of the main speakers. * While adjusting, the test-tone is fixed on the selected speaker. Remote control 5. Repeat step 3 and 4 to adjust the level of other speakers. 33 NOTE: If there is insufficient volume from the effect speakers, you may decrease the main speaker volume level by setting the MAIN LEVEL switch on the rear panel to “–10 dB”, and adjust each speaker level again. Volume controls on external power amplifiers may also be adjusted if necessary to achieve proper balance. 7. Adjust the front effect speaker level by pressing the + or – key so that it becomes almost as same as that of the main speakers. * While adjusting, the test-tone is fixed on the front effect speaker. Remote control NOTE: If not using a center speaker, be sure to set the “4. CENTER SPEAKER” in the SET MENU mode to the PHNTM (phantom) position. You will then hear the center channel test tone from the left and right main speakers. 8. When this adjustment is finished, press the TEST key once again. 6. For the front effect speaker level adjustment, depress the TEST key on the remote control again so that “TEST DSP” appears on the display panel. A calibration signal should be heard from the main speakers and the front effect speakers in turn (see diagram). Remote control TEST Remote control TEST Main Front MAIN FRONT * If the FRONT MIX switch on the rear panel is set to “ON (5ch)”, the front effect speaker level cannot be adjusted by this method. 34 NOTE: Once you have completed these adjustments, use only VOLUME control of this unit or MASTER VOLUME keys of the remote control unit to adjust the whole listening volume. Do not change any other volume setting in the system. ADJUSTMENTS IN THE “SET MENU” MODE 1. CENTER DELAY 2. DYNAMIC RANGE 3. LFE LEVEL 4. CENTER SPEAKER 5. REAR SPEAKER 6. MAIN SPEAKER 7. LFE/BASS OUT 8. INPUT MODE (TV/DBS) METHOD OF SETTING CHANGE AND ADJUSTMENT Operations should be made watching information on this unit’s display panel or the monitor screen. If you want to display information on the monitor, turn the power of the monitor on. English The following eight types of functions maximize the performance of your system and expand your enjoyment for audio listening and video watching. 1. If you will use the remote control unit, set the TIME/LEVEL·SET MENU switch to the SET MENU position on the remote control unit. NOTE: Be sure to use the remote control unit with the lid open. Remote control TIME/LEVEL SET MENU 2. Select the function (title) on which you will make a change. Remote control Front panel SET MENU or 3. Select any desired position or edit parameters on the function. Front panel Remote control or In the same way, make a setting change or adjustment on any other function. 35 DESCRIPTIONS OF THE FUNCTIONS 1. CENTER DELAY (Adjusting the delay of center sounds (dialog etc.)) Control range: 0 ms to 5 ms (in 1 ms step) Preset value: 0 ms * This adjustment is effective only when the Dolby Digital (AC-3) is decoded and the signals of selected source encoded with the Dolby Digital (AC-3) contain center-channel signals. Adjusts the delay between the main sounds (at the main channels) and dialog etc. (at the center channel). The larger the value, the later the dialog etc. is generated. This is for making sounds from the left main, center and right main speakers reach your listening position at the same time by delaying the sound from the center speaker if the distance from the center speaker to your listening position is shorter than the distance from the left or right main speaker to your listening position. 2. DYNAMIC RANGE (Adjusting dynamic range) Choices: MAX/STD/MIN Preset position: MAX * 36 This adjustment is effective only when the Dolby Digital (AC-3) is decoded. MAX: “Dynamic range” is the difference between the maximum level and the minimum level of sounds. Sounds on a movie originally designed for movie theaters feature very wide dynamic range. Dolby Digital (AC-3) technology can bring the original sound track into a home audio format with this wide dynamic range unchanged. In this position, a source encoded with the Dolby Digital (AC-3) is reproduced in the original sound track’s wide dynamic range providing you with powerful sounds like a movie theater. Selecting this position will be more ideal if you can listen to a source in a high output level in a room specially soundproofed for audio/video enjoyment. STD (Standard): Powerful sounds of extremely wide dynamic range are not always suitable for home use. Depending upon the condition of your listening environment, it may not possible to increase the sound output level as high as a movie theater, however, in a level proper for listening to in your room, the low level parts of source sound cannot be heard as well because they will be lost among noises in your environment. Dolby Digital (AC-3) technology also makes it possible to reduce an original sound track’s dynamic range for a home audio format by “compressing” the data. In this position, a source encoded with the Dolby Digital (AC-3) is reproduced in the “compressed” dynamic range of the source suitable for low level listening. MIN: In this position, dynamic range is more reduced than in the STD position. Selecting this position will be effective when you must listen to a source in extremely low level. Control range: –20 dB to 0 dB (in 1 dB step) Preset value: 0 dB * This adjustment is effective only when the Dolby Digital (AC-3) is decoded and the signals of selected source encoded with the Dolby Digital (AC-3) contain LFE signals. Adjusts the output level at the LFE (low frequency effect) channel. If the LFE signals are mixed with signals at other channels to output them from the same speakers, the ratio of LFE signal level to the level of other signals are adjusted. (See page 6 for details about the LFE channel.) 4. CENTER SPEAKER 5. REAR SPEAKER 8. INPUT MODE (Selecting the initial input mode of the sources connected to the TV/DBS input jacks) For the sources connected to the TV/DBS input jacks of this unit only, you can designate the input mode that is automatically selected when the power of this unit is switched on. English 3. LFE LEVEL (Adjusting the output level at the LFE (low frequency effect) channel) AUTO: In this position, the AUTO input mode is always selected when the power of this unit is switched on. LAST: In this position, the input mode you have selected last time is memorized and will not be changed even if the power of this unit is switched on. * See page 39 for details about switching the input mode. 6. MAIN SPEAKER 7. LFE/BASS OUT See pages 30 to 31 for details. (Once you have selected proper modes, you do not have to make a setting change until any alteration is made in your speaker system.) 37 GENERAL OPERATION PLAYING A SOURCE NOTE: If you will use the remote control unit, be sure to use it with the lid open. * To change the input mode for the DVD/LD or TV/DBS source, press the input selector button for the currently selected source once or more until the desired input mode (AUTO or ANALOG) is shown on the display panel. (See page 39 for details on switching the input mode.) Front panel 1. Set the master VOLUME control to minimum. Front panel VCR 1 Remote control DVD/LD DVD/LD VOLUME or l6 20 l2 TAPE (MD) 28 TV/DBS 8 4 40 2 60 0 –dB 2. Turn the power on. Front panel POWER PRO LOGIC SPEAKERS A 4. Play the source. 3. Select an input source. The selected source is shown by the display panel and the monitor screen. For the DVD/LD or TV/DBS source, its current input mode is also shown. 5. Increase the setting of the master VOLUME control to your listening level. Front panel Remote control VOLUME Front panel Remote control MASTER VOLUME l6 20 l2 28 VCR 1 8 DVD/LD DVD/LD 4 40 or MUTE or 2 60 TAPE (MD) TV/DBS 0 –dB Adjust the BASS, TREBLE, BALANCE controls, etc., or select a desired sound field program. (See page 42.) SPEAKERS A 38 DIGITAL DIGITAL Switching the input mode (for DVD/LD and TV/DBS) This unit allows you to switch the input mode only for sources connected to the DVD/LD and TV/DBS input jacks (on the rear of this unit) that input two or three types of signals to this unit. English Notes on using the input selector buttons • Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. * To select the source connected to the VIDEO AUX terminals on the front panel, press VIDEO AUX. • Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. • When you select an input source by pressing the corresponding input selector button, the DSP program (or the state of no DSP program is used) which was used when the same input source was selected the last time will automatically recalled. The following two input modes are provided. AUTO: For the source connected to the DVD/LD input jacks: This mode is automatically selected when you turn on the power of this unit. In this mode, input signal is automatically selected by the following order of priority. 1. Digital input signal from the OPTICAL jack 2. Digital input signal from the COAXIAL jack 3. Analog input signal For the source connected to the TV/DBS input jacks: This mode is automatically selected when you turn on the power of this unit if the “AUTO” position is selected on “8. INPUT MODE” in the SET MENU mode. (See page 37 for details.) In this mode, input signal is automatically selected by the following order of priority. 1. Digital input signal from the OPTICAL jack 2. Digital input signal from the COAXIAL jack 3. Analog input signal ANALOG: In this mode, only analog input signal is selected even though digital signal is input at the same time. Select this mode when you want to use the analog input signal instead of the digital input signal. NOTE: For the TV/DBS source only, the input mode selected on the function “8. INPUT MODE” in the SET MENU mode is selected when you turn on the power of this unit. 39 Notes on input mode selection • To play back a source with the Dolby Digital (AC-3) decoded, set the input mode to “AUTO”. • When you want to enjoy a source which has normal 2-channel signals with a Dolby Pro Logic Surround program, select the ANALOG mode. • In the AUTO mode, there may be a case depending on some LD players or DVD players that when you make a search on a source encoded with the Dolby Digital (AC-3) during the play and then the play is restored, sound output is interrupted for a moment because the digital input signal is selected again. RECORDING A SOURCE TO AUDIO/VIDEO TAPE (OR DUBBING FROM A TAPE TO ANOTHER) NOTE: If you will use the remote control unit, be sure to use it with the lid open. 1. Set the REC OUT selector to the SOURCE position. Front panel SOURCE DVD/LD TAPE (MD) TV/DBS TUNER VCR 1 CD VCR 2 PHONO VIDEO AUX REC OUT 2. Select the source you want to record. Front panel VCR 1 Remote control DVD/LD DVD/LD or TAPE (MD) TV/DBS 3. Play the source and increase the setting of the master VOLUME control to confirm it. Front panel Remote control VOLUME MASTER VOLUME l6 20 l2 28 8 4 40 or MUTE 2 60 0 –dB 40 4. Set the tape deck, MD recorder or VCR used for recording to the recording mode. While recording a source by setting the REC OUT selector to the position other than SOURCE as described above, the following operations can be made at the same time. ● ● You can monitor the audio (or the audio and video) signals being recorded by selecting the recording unit (TAPE (MD), VCR 1 or VCR 2) with the corresponding input selector button. You can watch or listen to any other source by selecting it with the corresponding input selector button. NOTE: Adjusting the master VOLUME, BASS, TREBLE controls, etc., or selecting a sound field program has no effect on the material being recorded. English Regardless of the setting of input selector buttons, when you set the REC OUT selector to a position other than “SOURCE”, the source selected by the REC OUT selector can be recorded by other tape deck (MD recorder) and/or VCRs connected to this unit. NOTE: Composite video and S video signals pass independently through this unit’s video circuits. Therefore, when recording or dubbing video signals, if your video source unit is connected to provide only a S video (or only a composite video) signal, you can record only a S video (or only a composite video) signal on your VCR. NOTE: A source that is connected to this unit between digital jacks only cannot be recorded by a tape deck or VCR connected to this unit. NOTE: Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. If you watch a video software that uses scramble or encoded signals to prevent it from being dubbed, there may be a case that display information superimposed on the picture and/or the picture itself is disturbed due to those signals. 41 SELECTING SOUND FIELD PROGRAMS This unit has 10 programs for digital sound field processing, 6 from actual acoustic environments from around the world, and 4 programs for Audio/Video sources including sources encoded with Dolby Pro Logic surround or Dolby Digital (AC-3). When operating on the front panel: 1. If no program name is illuminated on the display panel, press the EFFECT switch to turn on the digital sound field processor so that a name of sound field program lights up on the display panel and the monitor screen. To enjoy a video source with the Dolby Pro Logic Surround or Dolby Digital (AC-3) decoded When you select the program No. 1, 2 or 3, and the input signal of the source is 2-channel stereo, Dolby Pro Logic Surround is decoded. When some program is selected and the input signal of the source is encoded with the Dolby Digital (AC-3), Dolby Digital (AC-3) is automatically decoded. * The following indicators on the display panel show you what sound processing is being made. Front panel EFFECT DIGITAL PCM AC–3 Lights up when the Dolby Digital (AC-3) is being decoded and the signals of selected source encoded with the Dolby Digital (AC-3) is not in 2-channels. DSP 2. Select the desired sound field program by pressing the PROGRAM selector. * The name of selected program lights up on the display panel and the monitor screen. Front panel Lights up when the Digital Sound Field Processing is being made 3 DIGITAL DSP PRO LOGIC Lights up when the Dolby Pro Logic Surround is being decoded PROGRAM DIGITAL PCM AC–3 PRO LOGIC When operating on the remote control unit: * In addition, for the program No. 1, 2 and 3, the name of the program on the display panel or the monitor screen will change according to the type of decoding. (See pages 44–45 for details.) Simply pressing a DSP program selector key turns on the digital sound field processor and select the corresponding program directly. Remote control DIGITAL/ MOVIE PRO LOGIC ENHANCED THEATER 1 2 3 TV SPORTS STADIUM DISCO 5 6 4 ROCK 7 HALL 42 0 JAZZ CLUB CHURCH 8 9 NOTE: If the input signals of source encoded with the Dolby Digital (AC-3) are in 2-channels only, the sound processing for them is similar to that for analog or PCM audio signals. The EFFECT switch on the front panel and the EFFECT ON/OFF key on the remote control unit make it simple to compare the normal stereo sound with the fully processed effect sound. English CANCELING THE EFFECT SOUND To cancel the effect sound and monitor only the main sound, press the EFFECT ON/OFF key or the EFFECT switch. Press the EFFECT ON/OFF key or the EFFECT switch a second time to restore normal operation. Front panel Remote control EFFECT EFFECT or ON/OFF NOTES • If the effect sound is canceled when signals encoded with the Dolby Digital (AC-3) are input to this unit, signals of all channels are mixed and are output from the main speakers. • If the EFFECT switch or the EFFECT ON/OFF key is pressed to turn effect sounds OFF when the Dolby Digital (AC-3) is decoded, it may happen that sound is output faintly or not output normally depending on a source. In that case, press the EFFECT switch or the EFFECT ON/OFF key to turn effect sounds ON, or use input signals not encoded with the Dolby Digital (AC-3). 43 DESCRIPTIONS OF THE SOUND FIELD PROGRAMS The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for them was recorded at the locations described using sophisticated sound field measurement equipment. * The channel level balance between the left rear speaker and the right rear speaker may vary depending on the sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments. 1. DOLBY PRO LOGIC When the input signal is analog or PCM audio ( Speaker output: main, center, rear DOLBY DIGITAL When the input signal is Dolby Digital ( Speaker output: main, center, rear DIGITAL PRO LOGIC ) ) Reproduces video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. The built-in Dolby Pro Logic Surround decoder or Dolby Digital (AC-3) decoder precisely reproduces sounds and sound effects of a source encoded with Dolby Surround. The realization of a highly efficient decoding process improves crosstalk and channel separation and makes sound positioning smoother and more precise. 2. DOLBY PRO LOGIC ENHANCED When the input signal is analog or PCM audio PRO LOGIC ) ( DSP Speaker output: main, center, rear, front effect DOLBY DIGITAL ENHANCED When the input signal is Dolby Digital ( DIGITAL Speaker output: main, center, rear, front effect DSP ) Reproduces video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. This program ideally simulates the multisurround speaker systems of the 35 mm film theater. The Dolby Surround decoding and the digital sound field processing is precisely performed without altering the originally designed sound orientation. The surround effects produced by this sound field folds the viewer naturally from the rear to the left and right and toward the screen. NOTE: If the main channel sound is considerably altered by overadjustment of the BASS or TREBLE controls, the relationship with the rear channels may produce an unnatural effect. 44 DIGITAL MOVIE THEATER When the input signal is Dolby Digital ( DIGITAL Speaker output: main, center, rear, front effect 5. STADIUM When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect DSP English 3. MOVIE THEATER When the input signal is analog or PCM audio PRO LOGIC ) ( DSP Speaker output: main, center, rear, front effect ) This program gives you long delays between direct sounds and effect sounds, and extraordinarily spacious feel of a large stadium. Ideal for reproducing video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. This program is ideal for precisely reproducing the sound design of the newest 70 mm/Dolby Digital multi-track films. The sound field is made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. The three dimensional feeling of the sound field is emphasized, and dialog is precisely oriented on the screen. You can enjoy watching SciFi, adventure movies, etc. with much presence. 4. TV SPORTS 6. DISCO When the input signal is analog or PCM audio ( DSP ) Speaker output: main, center, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect This program is furnished with a tight sound field in which the sound will not spread excessively on the front side, but the rear surround side produces a dynamic sound expansion. This program is the most suitable for sports programs. When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. 45 7. ROCK CONCERT 9. CHURCH When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect This program is ideally suited for rock music. You will experience a very dynamic or lively sound field. 8. JAZZ CLUB This program recreates the acoustic environment of a big church with a high pointed dome and columns along the sides. This interior produces very long reverberations. 10. CONCERT HALL When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect This is a small, cozy jazz club with a low ceiling. The sound is very close and intimate. When the input signal is analog or PCM audio ( DSP ) Speaker output: main, rear, front effect When the input signal is Dolby Digital ( DIGITAL DSP ) Speaker output: main, center, rear, front effect In this program, the center will appear to be deep behind the main speakers, creating an expansive large hall ambience. Orchestra and opera music are suited for this sound field. NOTE: If the FRONT MIX switch on the rear panel is set to the “ON (5ch)” position, no sound is output from the front effect speakers, no matter what program is selected. Besides, if the “PHNTM” position is selected on “4. CENTER SPEAKER” in the SET MENU mode, no sound is output from the center speaker(s). 46 In using the digital sound field processor including the Dolby Pro Logic Decoder or the Dolby Digital (AC-3) Decoder, you can adjust delay time between the main sound and effect sound, and each speaker output level as you prefer. NOTE: These adjustments can be made only when the effect DIGITAL (or PRO LOGIC ) is not sound is on. If DSP and/or illuminated on the display panel, press the EFFECT switch on the front panel or the EFFECT ON/OFF key on the remote control unit so that at least one of those indicators lights up on the display panel. 1. If you will use the remote control unit, set the TIME/LEVEL·SET MENU switch to the TIME/LEVEL position on the remote control unit. NOTE: Be sure to use the remote control unit with the lid open. Remote control TIME/LEVEL SET MENU 2. Press once or more until the name of item on which you will make an adjustment appears on the display panel. Whenever pressed, the selection changes as follows. DELAY TIME CENTER LEVEL R SUR. LEVEL L SUR. LEVEL FRONT LEVEL SWFR LEVEL English ADJUSTING DELAY TIME AND EACH SPEAKER OUTPUT LEVEL (Delay time) (Center speaker output level) (Right rear speaker output level) (Left rear speaker output level) (Front effect speaker output level) (Subwoofer output level) * Depending on a mode of this unit, the number of selections is reduced. * Pressing the key on the remote control unit changes the selection in the reverse order. 3. Adjust its level. Front panel Remote control Remote control Front panel or DELAY/C/R /F/SWFR or 4. Repeat step 2 and 3 to make adjustments on other items. 47 Adjusting delay time Adjusting output level of the front effect, center, right rear and left rear speakers, and subwoofer You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear or front effect speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually. Program Control range (ms) 1. DOLBY PRO LOGIC DOLBY DIGITAL 2. PRO LOGIC ENHANCED DOLBY DIGITAL ENHANCED 3. MOVIE THEATER DIGITAL MOVIE THEATER 4. TV SPORTS 5. STADIUM 6. DISCO 7. ROCK CONCERT 8. JAZZ CLUB 9. CHURCH 10. CONCERT HALL 15 to 30 0 to 15 15 to 30 0 to 15 15 to 30 1 to 50 1 to 50 1 to 50 1 to 50 1 to 50 1 to 50 1 to 50 1 to 50 NOTES • Adding too much delay will cause an unnatural effect with some sources. • When the –/+ button is pressed, sound is momentarily interrupted. 48 If desired, you can adjust the sound output level of the each speaker even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on pages 33 to 34. Speakers Control range (dB) Preset value FRONT CENTER RIGHT SURROUND LEFT SURROUND SUBWOOFER MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to 0 0 0 0 0 0 NOTES • Output level of the front effect speakers cannot be adjusted when the program DOLBY PRO LOGIC (DOLBY DIGITAL) is selected. • Output level of the center speaker cannot be adjusted when the program STADIUM, DISCO, ROCK CONCERT, JAZZ CLUB, CHURCH or CONCERT HALL is selected, and the input signal is analog, PCM audio or encoded with the Dolby Digital (AC-3) in 2-channels. • Once the output level is adjusted, the level value will be the same in all the digital sound field programs. NOTE The values of the delay time and each speaker level you set the last time will remain memorized even when the power of this unit is off. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. SETTING THE SLEEP TIMER 2. The unit will be turned off automatically at the selected SLEEP time. English If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. To cancel the selected SLEEP time NOTES • The SLEEP timer can be controlled only with the remote control unit. • The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. Press the SLEEP key once or more so that “SLEEP OFF” appears on the display panel. (It will soon disappear and the “SLEEP” indicator will go off from the display panel.) SLEEP To set the SLEEP time 1. Press the SLEEP key. Indicates the SLEEP time. SLEEP SLEEP NOTE The SLEEP timer setting can also be canceled by turning off the power with the POWER switch or disconnecting the power plug of this unit from the AC outlet. Lights up. Press once or more to select the desired SLEEP time. Whenever the SLEEP key is pressed, the SLEEP time will change as follows. (Minutes) 120 90 60 30 The SLEEP timer is off (OFF). (The state before the SLEEP key is pressed.) After a while, the display returns to the indication before the SLEEP timer is set. 49 REMOTE CONTROL UNIT BASIC OPERATIONS (When the lid is open) LEARN MACRO REC/PAUSE E G NAMES OF KEYS AND THEIR FUNCTIONS H TRANSMIT /LEARN CLEAR The remote control unit provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player, tape deck, LD player etc. connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control unit will also control various functions of each component. * For basic operations, use the remote control unit with the lid open. A/B TAPE A CD 1 TUNER A DIR VCR 1 B STOP B DISC DVD/LD TV/DBS 2 1 Tape deck keys VCR 2 C 3 PRESET A/B/C/D/E DIGITAL/ MOVIE PRO LOGIC ENHANCED THEATER 4 Controls tape deck. (The A/B/C switch (G) should be set to the “A” position.) * DIR A, B and A/B are applicable only to double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. F 1 2 3 TV SPORTS STADIUM DISCO 4 5 6 ROCK V-AUX JAZZ CLUB CHURCH 7 8 HALL +10 9 TEST E PHONO EFFECT ON/OFF D SP A TIME/LEVEL C SYSTEM POWER OFF SET MENU MASTER VOLUME QUICK SLEEP MACRO SP B TV MUTE VCR OFF 9 B SLOW 5 6 7 8 LIGHT 0 A REMOTE CONTROL TRANSMITTER 50 2 CD/LD player keys Controls compact disc player or LD player. (To control compact disc player, set the A/B/C switch (G) to the “A” position. To control LD player, set the A/B/C switch (G) to the “C” position.) * DISC is applicable only to compact disc changer. * STOP is applicable only to LD player. 3 Tuner keys 0 Lid is open. I Side panel Controls tuner. (The A/B/C switch (G) should be set to the “A” position.) +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E: Selects the group (A – E) of preset station numbers. Selects a DSP program when the built-in digital sound field processor (including the Dolby Pro Logic Surround Decoder or the Dolby Digital (AC-3) Decoder) is on. 5 TEST key 0 RESET button This button is inside the battery compartment. Press this button to “reset” the internal microcomputer which controls remote control operations. Microcomputer “reset” is necessary when the remote control freezes. * Pressing the RESET button will not erase learned functions. Used when you make the speaker balance adjustment to maximize the performance of your audio/video system including this unit. (For details, refer to page 33–34.) English 4 DSP program selector keys RESET button 6 SP A and SP B keys Select the main speakers A or B (or both A and B) you will use by pressing the corresponding key “SP A” or “SP B” (or both keys) so that “SPEAKERS A” or “SPEAKERS B” (or both of them) lights up on the display panel. To cancel selected speakers, press the corresponding key so that the corresponding indicator goes off from the display panel. A MASTER VOLUME (up) and Turns the volume level up and down. (down) keys B MUTE key 7 SLEEP timer key This key is used to turn the built-in SLEEP timer on and off, and to set the SLEEP time. (See page 49 for details.) When pressed, this key mutes the volume level. To resume the original volume level, press this key again. While muting, the indicator on the VOLUME control flashes continuously. 8 TIME/LEVEL·SET MENU switch Set to the TIME/LEVEL position when you will make an adjustment on delay time, center speaker output level, rear speaker output level, front effect speaker level or subwoofer level. Set to the SET MENU position when you will make an adjustment or setting change on a function in the SET MENU mode. C 9 SYSTEM POWER and OFF keys D EFFECT ON/OFF key While the power is on, pressing the OFF key switches the unit from the power-on mode to the standby mode and pressing the SYSTEM POWER key switches the unit from the standby mode to the power-on mode. (In the standby mode, the standby indicator on the front panel is illuminated.) Switches on/off the digital sound field processor (including the Dolby Pro Logic Surround Decoder or the Dolby Digital (AC-3) Decoder). / and –/+ keys (up) and (down) keys change items (or functions) in the mode selected by the TIME/LEVEL·SET MENU switch. – and + keys make an adjustment or setting change on the item (or function) selected by the or key. E Input selector keys Selects input source. 51 F A/B/C indicators The position (A, B or C) selected by the A/B/C switch is shown in red. G A/B/C switch This switch must be used only when the lid of the remote control unit is open. (This switch will not function when the lid is closed.) Normally, set this switch to the “A” position. When controlling a Yamaha LD player by using the CD/LD player keys (2), set this switch to the “C” position. H TRANSMIT/LEARN indicator Lights up when the remote control unit is transmitting infrared signals (when a command key is pressed). I LIGHT key If this key is pressed, some of the keys on the remote control unit light up for about 5 seconds. If this key is pressed while those keys are lighting up, they stop lighting. NOTE When using the keys to control Yamaha components, identify them with your component’s keys. If these keys are identical, their functions will be the same. For each key function, refer to the corresponding instruction in your component’s manual. 52 LEARNING NEW CONTROL FUNCTIONS (When the lid is open) This is a learning remote control unit. The shaded keys in the illustration shown right can be programmed to “learn” control functions from other remote control units. By learning keyfunctions from other remote control unit, this unit can then be used in place of one or more other remote control units, thus making operation of your various audio and video components more convenient. Some of the “learning-capable” keys are originally empty and others have already been preset with functions to control this unit and other Yamaha components. You can store new functions to them (in place of preset functions) as desired. * See pages 61 to 62 for the learning method. * See pages 64 to 65 for clearing a learned function (or all learned functions). NOTE If the memory capacity of the remote control unit becomes full, no further learning is possible even if some learning-capable keys are not occupied with new functions. If, for example, you store only Yamaha codes into this remote control unit, up to about 50 functions can be stored. Store new functions to the learnablecapable keys which are useful for you. Keys which can have three functions (1, 2, 3, 4) * In the “Learning-capable” keys, the keys of groups numbered TRANSMIT /LEARN CLEAR LEARN 1–4 in the illustration at left can have three functions. This is MACRO REC/PAUSE A/B TAPE A TUNER A DIR VCR 1 B STOP B DISC DVD/LD TV/DBS 2 A/B/C switch CD 1 VCR 2 C 3 PRESET 2 A/B/C/D/E DIGITAL/ MOVIE PRO LOGIC ENHANCED THEATER 4 1 2 3 TV SPORTS STADIUM DISCO 4 5 6 ROCK because they have three memory areas (A, B and C). (One function per area.) You can store new functions into the area B and C, and use three functions on a key by switching the memory areas with the A/B/C switch. (Area A cannot learn a new function.) To use these keys: 1. Before using a key, select the area A, B or C of the key on which the function you want to use is stored by using the A/B/C switch. 2. Press the key. The original factory settings of these keys are as follows. V-AUX PHONO JAZZ CLUB CHURCH 7 8 9 HALL +10 TEST EFFECT ON/OFF 0 1 SP A TIME/LEVEL SP B SLEEP SET MENU SYSTEM POWER 2 MASTER VOLUME TV 1 English 1 3 MUTE VCR OFF 4 The position of A/B/C switch B C A Empty Preset with functions Empty for controlling a Yamaha tape deck. Preset with functions Empty Preset with functions for controlling a for controlling a Yamaha LD player. Yamaha CD player. (DISC is empty.) (STOP is empty.) Empty Empty Preset with functions for controlling a Yamaha tuner. Preset as the DSP Preset as the DSP Preset as the DSP program selector keys program selector keys program selector keys (1–9, 0) and the TEST (1–9, 0) and the TEST (1–9, 0) and the TEST key. key. key. (+10 is empty.) (+10 is empty.) (+10 is empty.) REMOTE CONTROL TRANSMITTER Lid is open. 1 : These buttons are used for learning a new function or clearing a learned * function (or all learned functions). See pages 61 to 65 for details. NOTE The area A of any key cannot learn a new function. To store a new function to a key, store it into the area B or C. 53 Empty keys (1, 2) About the lighting of keys These are empty keys. Each key can learn a function from another remote control unit. For example, the TV key is useful for storing the function of your TV’s power switch, and the VCR key can be used for your VCR’s power switch. When you press an input selector key, it lights up for about 3 seconds. NOTE If a key which has a preset function learns a new function, the preset function will not be deleted, but disabled. When the learned function is cleared, the preset function is restored. (For information on clearing a learned function, refer to pages 64 to 65.) When an input selector key in the group of selected memory area (A, B or C) is pressed, the mark of key group (1–3) which is the same as the mark of the selected input selector key lights up for about 3 seconds. Example) Lights up. About the marks shown on the remote control unit TRANSMIT /LEARN CLEAR LEARN MACRO REC/PAUSE A/B TAPE The marks on the remote control unit signify functions of keys, input sources, etc. A CD Red (This shows that the memory area A is selected.) TUNER Examples) (tape): Shows tape deck, VCR, etc. (disc): Shows CD player, LD player, etc. (radio wave): Shows tuner, TV/BS tuner, etc. These marks are helpful for storing new functions. Examples) • The area B of keys 1 is suitable for storing functions to control your VCR. • The area B of keys 3 is suitable for storing functions to control your TV/BS tuner. 54 A STOP DIR VCR 1 B DISC B Conversely, when a key of group 1–3 is pressed, its mark and the input selector key with the same mark in the group of the selected memory area light up for about 3 seconds. This feature may be helpful for you if you store functions for controlling an input source to a group of keys whose mark lights up when the corresponding input selector key is pressed. CLEAR REMOTE CONTROL TRANSMITTER LEARN MACRO REC/PAUSE A/B TUNER VCR 1 DVD/LD TV/DBS TAPE Input selector keys TAPE CD When the lid of the remote control unit is closed, you can easily operate Yamaha components including learned functions by using the OPERATION CONTROL keys. TRANSMIT /LEARN TRANSMIT A CD 1 TUNER A DIR VCR 1 B STOP B DISC DVD/LD TV/DBS 2 VCR 2 VCR 2 C 2 * 3 PRESET A/B/C/D/E PHONO EFFECT OPERATION CONTROL SYSTEM POWER MASTER VOLUME TV OPERATION CONTROL keys DIGITAL/ MOVIE PRO LOGIC ENHANCED THEATER V-AUX 1 2 3 TV SPORTS STADIUM DISCO 5 6 4 ROCK V-AUX PHONO JAZZ CLUB CHURCH 7 8 HALL +10 9 TEST EFFECT ON/OFF 0 SP A TIME/LEVEL (+10) SP B SLEEP When the lid is closed, the OPERATION CONTROL keys substitute for the keys of group numbered 1, 2 or 3 and the (+10) key on the left illustration. To use these keys, you do not have to switch the A/B/C switch. The functions which the OPERATION CONTROL keys carry out are determined by which input selector key was pressed before you use the OPERATION CONTROL keys. NOTE When the lid is closed, the EFFECT, MASTER VOLUME, MUTE, TV and VCR keys will function in the same way as when the lid is open. * If the MACRO switch on the side of the remote control unit is set to “OFF”, when the lid is closed, the SYSTEM POWER and OFF keys also will function in the same way as when the lid is open. SET MENU SYSTEM POWER MASTER VOLUME TV MUTE VCR English USING OPERATION CONTROL KEYS (When the lid is closed) MUTE VCR OFF OFF REMOTE CONTROL TRANSMITTER Lid is closed. 2 : These keys are originally empty. If these keys have learned functions, pressing * them executes those learned functions. 55 See the table below for a combination of an input selector key and key functions which the OPERATION CONTROL keys carry out. (Also, refer to the table on page 53.) Key functions which the OPERATION CONTROL keys carry out Selected input selector Functions in area A of keys 1 (except REC/PAUSE, A/B, DIR A and B) TAPE Functions in area A of keys 2 (except STOP, DISC, CD and ) TUNER Functions in area A of keys 3 and VCR 1 Functions in area B of keys 1 (except REC/PAUSE, A/B, DIR A and B) (+10) DVD/LD Functions in area B of keys 2 (except STOP, DISC, TV/DBS Functions in area B of keys 3 and and ) (+10) Functions in area C of keys 1 (except REC/PAUSE, A/B, DIR A and B) VCR 2 Functions in area C of keys 2 (except STOP, DISC, Functions in area C of keys 3 and and ) (+10) Pressing the “V-AUX” or “PHONO” input selector key has no effect on the OPERATION CONTROL keys. Examples of operations controlled by using the OPERATION CONTROL keys To operate a Yamaha CD player 1. Press the “CD” input selector key. 2. Use the OPERATION CONTROL keys. (They carry out the functions in area A of keys 2.) Skip to previous track OPERATION CONTROL Play To operate your VCR 1. Press the “VCR” input selector key. 2. Use the OPERATION CONTROL keys. (They carry out the functions in area B of keys 1. This area is originally preset with no function. You must store the functions related to controlling the VCR in area B of keys 1 beforehand.) Skip to next track OPERATION CONTROL Rewind Play Fast forward Pause or Stop Pause or Stop 56 • English NOTES • If the OPERATION CONTROL keys substitute for keys which has no function (empty), no command is carried out. According to your plan, store functions from other remote control units into an empty area of those keys. (Refer to pages 61 to 62 for the learning method.) While playing an audio/video unit, if you want to operate another unit by using the remote control unit (for example, if you want to rewind a tape on your VCR while listening to a CD), you should open the lid of the remote control unit and use the A/B/C switch and the corresponding keys. (If you press an input selector key with the lid closed to change the functions of the OPERATION CONTROL keys to the functions for controlling a VCR, the input of currently playing CD source is canceled.) About the lighting of keys When an input selector key is pressed, the pressed key and only the available OPERATION CONTROL keys (which substitute for the keys stored with the preset functions or learned functions) light up for about 3 seconds. So you can know what keys are available at a glance. OPERATION CONTROL TUNER Conversely, when an OPERATION CONTROL key is pressed, all of the available OPERATION CONTROL keys and the currently selected input selector key light up. 57 MACRO OPERATIONS (When the lid is closed) Preset macro keys TRANSMIT /LEARN CLEAR TRANSMIT “Macro” is a command which defines a sequence of several operations. LEARN REC/PAUSE REMOTE CONTROL TRANSMITTER TAPE A CD 1 CD TUNER TUNER A VCR 1 DIR VCR 1 B STOP B DISC DVD/LD DVD/LD TV/DBS 2 TV/DBS VCR 2 VCR 2 C PRESET A/B/C/D/E DIGITAL/ MOVIE PRO LOGIC ENHANCED THEATER V-AUX 1 2 3 TV SPORTS STADIUM DISCO 5 6 4 PHONO Preset macro keys are originally preset with macros. If you prefer, however, you can change the contents of a macro key by storing a desired series of functions on it. You can store up to seven functions onto a macro key. (See page 63 for the learning method.) ROCK EFFECT OPERATION CONTROL V-AUX PHONO JAZZ CLUB CHURCH 7 8 HALL +10 9 TEST EFFECT ON/OFF 0 LIGHT SP A TIME/LEVEL MUTE MACRO switch SLOW TV QUICK MASTER VOLUME OFF MACRO SP B SYSTEM POWER SLEEP SET MENU SYSTEM POWER MASTER VOLUME TV MUTE VCR OFF VCR OFF REMOTE CONTROL TRANSMITTER Lid is closed. (Set the MACRO switch to “QUICK” or “SLOW”.) 58 A/B TAPE The keys shown in the right illustrations (as “preset macro keys”) are also preset with macros, in addition to individual functions. Each macro key is preset so that simply pressing it alone will carry out several functions of other keys on this remote control unit sequentially. (To know what key functions are sequentially carried out by pressing each preset macro key, see the next page.) Macros can be used only when the lid is closed and the MACRO switch is set to “SLOW” or “QUICK”. (If “OFF” is selected, no macro will function even if the lid is closed.) Setting the MACRO switch OFF: In this position, no macro will function even if the lid of remote control unit is closed. QUICK: In this position, when a macro key is pressed, each command is transmitted at 0.5 second intervals. SLOW: In this position, when a macro key is pressed, each command is transmitted at 3 second intervals. MACRO English Preset macro keys and the key functions which they carry out sequentially are as follows. (Also, refer to the table on page 53.) Function of the key (and area) which operates when a macro key is pressed Macro key 1st (Turning the power of this unit on) 2nd (Selecting an input source) 3rd (Playing a source) TAPE TAPE “ ” on area A of keys 1 CD CD “ ” on area A of keys 2 TUNER TUNER VCR 1 VCR 1 “ ” on area B of keys 1 DVD/LD “ ” on area B of keys 2 DVD/LD SYSTEM POWER TV/DBS TV/DBS VCR 2 VCR 2 – – “ ” on area C of keys 1 “ ” on area C of keys 2 – V-AUX V-AUX – PHONO PHONO – Function of the key which operates when a macro key is pressed Macro key SYSTEM POWER 1st SYSTEM POWER 2nd 3rd TV VCR – OFF – OFF 59 NOTES • A key in which no function is stored will carry out no command. • If it occurs that this unit will not receive the second command because the internal operation of the first command takes a long time, set the MACRO switch to the “SLOW” position, or add no function or repeat the same command between the first command and the next command. • If you will program the power on/off switching function of TV, VCR, etc. as part of a macro sequence, note that it switches the current mode to the other (“on” to “off”, or “off” to “on”). For example, when you press the macro key, if the power of TV, VCR, etc. is already on, the power will be turned off even though you may not want it to do so. • Once you press a macro key, this unit will not receive the command of another key (even if it is pressed) until this unit finishes carrying out all commands of the macro key. Take notice of this especially when the MACRO switch is in the “SLOW” position. • Once you press a macro key, you must keep the remote control unit directed at the main unit’s remote control sensor until the remote control unit finishes transmitting all command signals of the macro key. • You can use the OPERATION CONTROL keys also while using the macro functions. 60 1. Place this remote control unit and the other remote control unit so that they face each other. 3. If necessary, select the memory area by using the A/B/C switch on the side panel of the remote control unit. English LEARNING A NEW FUNCTION This remote control unit TV RTS O 1 M IU AD ST 5 2 Z Other remote control unit 3 IS D UB CL ES -A V H RC U CH 9 6 CO U X H P T O T C FE F EF /OF ON N O 4. Press the key on this remote control unit in which you will store a new function. About 5–10 cm (2–4 in.) P 3 CO IS D 2 6 H M IU RC AD U ST CH 9 1 5 UB TV TS ST CL OR TE ZZ JA 8 4 0 CK RO +1 7 L L SP 2. Press the LEARN button using the point of a mechanical pencil etc. Lights up. X U -A V O T C FE F EF /OF ON N O H TRANSMIT /LEARN LEARN MACRO Flashes slowly. * If there is no operation for about 30 seconds after the LEARN button is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled. If this occurs, repeat this step. E CLEAR * If a key which cannot learn another function is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled. If this occurs, repeat this step. * If there is no operation for about 30 seconds after a key is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you began learning operations is restored. If this occurs, restart from step 2. 61 5. Press and hold the key (on the other remote control unit) which has the function you want to store. 3 D IS U X H P T -A V S TE H RC U CH 9 6 CO 0 1 B U CL ZZ JA 8 2 M IU AD ST 5 K OC TV RTS O 4 SP 1 O T C FE F EF /OF ON N O * When learning is finished, the TRANSMIT/LEARN indicator stops lighting and then begins flashing slowly. * If a signal is not successfully received, the TRANSMIT/LEARN indicator flashes rapidly and the mode prior to step 4 is restored. If this occurs, restart from step 4. * If memory capacity is full, the TRANSMIT/LEARN indicator flashes rapidly to show you that learning is impossible, and then the mode before you began learning operations is restored. 6. Repeat step 3–5 to store more functions. 7. When you finish the learning operation, press the LEARN button. CLEAR 62 LEARN MACRO NOTES • Newly learned functions will replace previously learned functions. • If there is no more room in the memory area for a function to be learned, the TRANSMIT/LEARN indicator will flash rapidly. In this case, even if some keys are not occupied with functions from other remote control units, no further learning is possible. • If the lid is closed while learning and about 5 seconds pass, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you began learning operations is restored. If this occurs, restart from step 2. However, if the lid is opened within 5 seconds, the mode before the lid was closed is restored. • There may occasionally be instances in which, due to the signal-coding and modulation employed by the other remote control unit, this remote control unit will not be able to “learn” its signals. A new macro can be programmed onto any preset macro key in place of preset functions. (See page 58 to know what keys are preset macro keys.) You can make as many as 13 new macro keys. A macro key can learn as many as seven functions of other keys. NOTE If you store a continuous command such as lowering of volume level, it will become a short command when it is carried out as a part of macro. 1. Press the MACRO button using the point of a mechanical pencil etc. TRANSMIT /LEARN CLEAR LEARN MACRO 3. Press a key whose function you want to store as the first function of the new macro. SYSTEM POWER English MAKING A NEW MACRO TRANSMIT /LEARN Goes off. (When learning is finished, this indicator lights up again.) * If a key whose function cannot be stored as a command of macro is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled. If this occurs, repeat this step. * If about 30 seconds pass before a key is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you began learning operations is restored. If this occurs, restart from step 1. Flashes slowly. * If there is no operation for about 30 seconds after the MACRO button is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you pressed the MACRO button is restored. If this occurs, press the MACRO button again. 2. Press a preset macro key on which you want to make a new macro. CD TRANSMIT /LEARN 4. Repeat step 3 to store the second, the third and more functions. You can store up to seven key functions in series as a macro. * If the seventh key function has been learned, the TRANSMIT/LEARN indicator flashes rapidly and the mode before you began learning operations is restored. (This shows that the key has completed learning a series of functions as a macro.) If this occurs, you do no have to follow the next step. 5. When you finish learning, press the MACRO button. Lights up. * If a key other than a preset macro key is pressed, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled. If this occurs, repeat this step. CLEAR LEARN MACRO 63 It is recommended to write down new key functions you stored on the provided user function stickers and paste them on the reverse side of the remote control unit or the reverse side of the remote control unit’s lid. CLEARING LEARNED FUNCTIONS To Clear a Learned Function 1. To clear a learned key function, press the LEARN button using the point of a mechanical pencil, etc. To clear a macro you made, press the MACRO button. or TRANSMIT /LEARN CLEAR LEARN MACRO A Flashes slowly. B C 2. Press and hold the CLEAR button using the point of a mechanical pencil, etc. CLEAR LEARN MACRO REMOTE CONTROL TRANSMITTER 3. Holding the CLEAR button pressed, press and hold the key whose function you want to clear until the indicator flashes 3 times. CD Memory back-up All of the learned functions will be retained while you replace the batteries. However, if no batteries are installed for a few hours, the learned functions will be erased and will have to be learned again. TRANSMIT /LEARN Flashes. To clear two or more functions sequentially, do not release the CLEAR button pressed, and repeat this step. NOTE If you clear a learned function of a key, the originally preset function of the key is restored (except the keys which are originally preset with no function.) 64 1. Select the kind of key functions all of which you want to clear by using the MACRO switch on the side panel of the remote control unit. SLOW QUICK OFF 3. Press and hold the CLEAR button again. While holding the CLEAR button pressed, press and hold the MASTER VOLUME and keys simultaneously until the indicator flashes 7 times. English To Clear All Learned Functions TRANSMIT /LEARN MACRO MUTE Flashes. OFF: Select this position if you want to clear all of the learned functions except macros. QUICK: Select this position if you want to clear all of the macros you made only. SLOW: Select this position if you want to clear all of the learned functions including macros. 2. Press the CLEAR button using the point of a mechanical pencil, etc. TRANSMIT /LEARN CLEAR LEARN MACRO Flashes slowly. * If one of the following operation is made after you press the CLEAR button, the TRANSMIT/LEARN indicator flashes rapidly and the current mode is canceled. If this occurs, press the CLEAR button again. • MACRO switch is switched to another position. • Another key is pressed. • There is no operation for about 30 seconds. 65 TROUBLESHOOTING PROBLEM Power does not come on. The unit turns off suddenly soon after the power is turned on. Hum. No sound. No sound from the effect speakers. No sound from the front effect speakers. No sound from the center speaker. Poor bass reproduction. The sound suddenly goes off. The volume level cannot be increased, or sound is distorted. The sound field cannot be recorded. This unit will not operate properly. 66 POSSIBLE CAUSE AC cord not properly plugged in. The IMPEDANCE SELECTOR switch on the rear panel is not set to the upper or the lower end exactly. Bad cable connection. Bad or incorrect input connection. Incorrect input source selection. Digital signals other than PCM audio or the Dolby Digital (AC-3) encoded signals which this unit cannot reproduce are input to this unit by playing a CD-ROM etc. The EFFECT switch is set off. A Dolby Surround decoding program is being used with material not encoded with Dolby Surround. The FRONT MIX switch is set to “ON”. The sound field program No. 1 “DOLBY PRO LOGIC (DOLBY DIGITAL)” is selected. The CENTER SPEAKERS mode is in “PHNTM”. One of the sound field programs No. 5 to No. 10 is selected when the input signal of source is 2channel stereo (analog/PCM). The input signals of source encoded with the Dolby Digital (AC-3) do not have center channel signals. The LFE/BASS OUT mode is in the SWFR or BOTH position, though your system does not include a subwoofer. Output mode selection for each channel (MAIN, CENTER or REAR) is improper. The protection circuit has activated because of short circuit etc. The power to the component connected to the REC OUT jacks of this unit is off. It is not possible to record the sound field on a tape deck connected to this unit’s TAPE REC OUT jacks. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or power supply with low voltage. WHAT TO DO Carefully plug AC plug into outlet. Set the switch to the upper or the lower end exactly. Firmly plug in all connection cables. Check connections. Select the appropriate input source with the input selector buttons. Play a source whose signals this unit can reproduce. Press the EFFECT switch to turn it on. Use a different sound field program. Set the FRONT MIX switch to “OFF”. Select another program. Select the appropriate mode. Select another program. Refer to the instructions for the source currently played. Select the MAIN position. Make output mode selections suitable for your speaker system. Turning the unit off and then on will reset the protection circuit. Turn the power to the component on. Unplug the AC power cord from the wall AC outlet, and then plug in again after about one minute. The remote control unit does not function properly. Learning cannot be made successfully. (The TRANSMIT/LEARN indicator does not light up or flash.) Continuous functions such as volume are learned, but operate only for a moment before stopping. POSSIBLE CAUSE The source unit is connected to this unit between digital jacks only. This unit is too close to the affected equipment. The power to this unit is off. WHAT TO DO Make additional connection between analog jacks. The batteries of this remote control unit are weak. The internal microcomputer “freezes”. Wrong distance or angle. Replace the batteries with new ones and press the RESET button on the remote control unit. Press the RESET button on the remote control unit. The remote control unit will function from a maximum range of 6 meters, no more than 30 degrees off-axis from the front panel. Change position of the main unit. Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remotecontrol sensor of the main unit. The internal microcomputer “freezes”. The batteries of this remote control unit and/or the other remote control unit are weak. The distance between the two remote control units is too long or too short. The signal coding or modulation of the other remote control unit is not compatible with this remote control unit. Memory capacity is full. The internal microcomputer “freezes”. Learning process incomplete. Move the unit further away from the affected equipment. Turn the power to this unit on. English PROBLEM A source cannot be recorded by a tape deck or VCR connected to this unit. Noise from nearby TV or tuner. The sound is degraded when listening with the headphones connected to the compact disc player or cassette deck that are connected with this unit. The remote control unit does not work. Press the RESET button on the remote control unit. Replace the batteries (and press the RESET button for this remote control unit). Place the remote control units with the proper distance. Learning is not possible. Further learning is not possible without deleting unnecessary commands. Press the RESET button on the remote control unit. Be sure to press and hold the function key on the other remote control until the TRANSMIT/LEARN indicator begins flashing slowly. 67 SPECIFICATIONS Minimum RMS Output Power Per Channel Main (20 Hz – 20 kHz 0.02% THD 8Ω) ........................................... 80W+80W Center (20 Hz – 20 kHz 0.02% THD 8Ω) ................................................. 80W Front Effect (1 kHz 0.05% THD 8Ω)..................................................25W+25W Rear (20 Hz – 20 kHz 0.02% THD 8Ω) ........................................... 80W+80W Dynamic Power Per Channel (by IHF Dynamic Headroom Measuring Method) MAIN L/R (8Ω/6Ω/4Ω/2Ω) ............................................. 130W/160W/200W/240W Maximum Output Power [General model] MAIN L/R (1 kHz 10% THD 8Ω) ....................................................... 128W+128W DIN Standard Output Power Per Channel [Europe model] MAIN L/R (1 kHz 0.7% THD 4Ω) ............................................................. 128W IEC Power [Europe model] MAIN L/R (1 kHz 0.015% THD 8Ω) ......................................................... 100W Power Band Width MAIN L/R (40W 0.08% THD 8Ω) ............................................ 10 Hz to 50 kHz Damping Factor MAIN L/R (20 Hz – 20 kHz 8Ω, SPEAKERS A) ........................... 200 or more Input Sensitivity/Impedance (100W/8Ω) CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX ............. 150 mV/47 kΩ PHONO MM.................................................................................2.5 mV/47 kΩ MAIN IN ..............................................................................................1V/47 kΩ Maximum Input Signal CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX (1 kHz 0.5% THD, EFFECT ON) ............................................... 2.2V or more PHONO MM (1 kHz 0.04% THD)............................................ 110 mV or more Output Level/Impedance REC OUT.................................................................................. 150 mV/2.7 kΩ PRE OUT MAIN ............................................................................................... 1V/1.2 kΩ SUBWOOFER (MAIN SPEAKERS: SMALL) .............................. 4.0V/1.2 kΩ 68 Headphone Jack Rated Output/Impedance Output Level (CD Input 150 mV, RL=8Ω).................................................. 0.5V Impedance .............................................................................................. 440Ω Frequency Response (20 Hz – 20 kHz) MAIN IN ............................................................................................. 0±0.5 dB CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to MAIN L/R SP OUT ........................................................................................................... 0±0.5 dB RIAA Equalization Deviation (20 Hz – 20 kHz) PHONO MM ........................................................................................0±0.5 dB Total Harmonic Distortion PHONO MM to REC OUT, 20 Hz – 20 kHz, 1V.......................... 0.01% or less MAIN IN to SP OUT (MAIN L/R, CENTER), 20 Hz–20 kHz, 40W/8Ω .................................................................................................. 0.008% or less CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT (MAIN L/R, CENTER), 20 Hz – 20 kHz, 40W/8Ω...................... 0.015% or less CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT (REAR L/R), 1 kHz, 40W/8Ω......................................................... 0.3% or less CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT (FRONT L/R), 1 kHz, 12.5W/8Ω ................................................... 0.3% or less DIGITAL IN (DVD/LD) to SP OUT (MAIN L/R, CENTER, REAR L/R), 20 Hz – 20 kHz, 40W/8Ω ............................................................ 0.03% or less Signal-to-Noise Ratio (IHF-A Network) CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX to SP OUT (Input Shorted 150 mV) (EFFECT OFF) ................................. 96 dB or more PHONO MM to REC OUT (Input Shorted 5 mV) [Europe, U.K. and Australia models] ........................................ 82 dB or more [General model] ....................................................................... 86 dB or more Residual Noise (IHF-A Network) MAIN L/R SP OUT ..................................................................... 170 µV or less Channel Separation (Vol. –30 dB) CD/TUNER/TAPE/DVDzLD/TVzDBS/VCR/VIDEO AUX (Input 5.1 kΩ Shorted) (EFFECT OFF) 1 kHz/10 kHz ....................................... 60 dB/45 dB or more PHONO MM (Input Shorted) (EFFECT OFF) 1 kHz/10 kHz ................................................................. 60 dB/55 dB or more YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VY77910 Printed in Japan