Jacobsen 10029629 Maintenance Manual

Marca: Jacobsen

Modelo: 10029629

Categoría: Cortadoras de césped

Tipo: Maintenance Manual

Este manual también es adecuado para

10029628

AR Series Mower / Segadora Serie AR

10029628 - AR730 T4F

Series / Serie: BAM

10029629 - AR730 Stage V

Series / Serie: BAN

Kubota® V2403-T-E4B T4F/V2403-CR-TE5B-TXN-1

4WD / Tracción a las 4 ruedas

Reversing Fan / Ventilador de inversión

673834-B-ES

RJL AFCB

Safety Operation and Maintenance Manual

Manual de seguridad, funcionamiento y mantenimiento

ADVERTENCIA: Si se usa de forma incorrecta esta máquina puede causar graves lesiones. Cualquier persona

que use y mantenga esta máquina deberá estar entrenado en su uso correcto, instruido sobre sus peligros y

deberá leer el manual completamente antes de tratar de instalar, operar, ajustar o revisar la máquina.

ADVERTENCIA

WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this

machine must be trained in its proper use, warned of its dangers and must read the entire manual before

attempting to set up, operate, adjust or service the machine.

WARNING

1 CONTENTS

en-1

1Contents

FOREWORD

This manual contains adjustment, maintenance, and

troubleshooting instructions for your new Jacobsen

machine. This manual should be stored with the

equipment for reference during operation.

Before you operate your machine, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating and

maintenance instructions, you will prolong the life of your

equipment and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

SERVICE SUPPORT MATERIAL

Part No. Description

673834Safety, Operation & Maintenance Manual

673837Parts Manual

4299117 Kubota V2403-T-E4B Engine Parts Manual

689336 Kubota V2403-CR-TE5B Engine Parts Manual

Part No. Description

This manual may not re reproduced in whole or in part without the express permission of TSV Technical Communications Department.

09-2020

CALIFORNIA PROPOSITION 65

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects and other reproductive harm.

Blade Recommendations

AR730 - 23” BLADE RECOMMENDATION

DISCHARGE MODE MULCH MODE COMMENTS

Vortex Combo Best cut quality; good distribution

Good hiding of clippings for cool and warm

season grasses; best quality cut

Best all around blade in cool and warm

season grasses

692774 Good all around blade Sometimes best blade for Bermuda

Extreme Mulch

In certain conditions best distribution, but

some degradation in cut quality

Best blade for hiding, but some degrada-

tion in cut quality

Performance is very dependent on spe-

cific local conditions

692775 Often the best blade for Bermuda Often the best blade for Bermuda

High Lift Use for very heavy conditions Not recommended Not Available for European Market

692771 Helps with distribution in cool season

grass, especially in the Spring Not recommended

Note: * These recommendations are intended as an initial guide for blade selection.

Grass type, regional climates, height of cut, and customer preferences will affect the actual blade choice.

** Due to sound level regulations, some blades may not be available in all regions. Please check with your local dealer for

availability.

TABLE OF CONTENTS

Contents

Introduction

1.1 Important.............................................................................2

1.2 Product Identification...........................................................3

1.3 Key Numbers ......................................................................3

1.4 parts manual .......................................................................3

1.5 Guidelines For The Disposal Of Scrap Products ................4

Safety

2.1 How to Operate Safely........................................................5

Labels

3.1 Safety Labels ....................................................................12

3.2 Instruction Labels ..............................................................14

Controls

4.1 Operator Compartment .....................................................15

4.2 Control Panel ....................................................................16

4.3 Armrest Adjuster ...............................................................43

4.4 Traction Pedal...................................................................43

4.5 Steering Tilt Control ..........................................................43

4.6 Tow Valve .........................................................................44

4.7 Parking Brake Release Valve ...........................................44

Operation

5.1 Daily Inspection.................................................................45

5.2 Interlock System................................................................46

5.3 Operating Procedure.........................................................47

5.4 Starting The Engine ..........................................................48

5.5 To Stop The Engine ..........................................................48

5.6 Driving...............................................................................49

5.7 Traction Modes .................................................................49

5.8 Mowing Speed ..................................................................49

5.9 Mowing..............................................................................49

5.10 Mowing On Slopes..........................................................50

5.11 Towing The Mower..........................................................52

5.12 To Remove A Blockage From Cutting Implements .........53

5.13 SLINGING and jacking THE MACHINE..........................53

Adjustments

6.1 General Precautions .........................................................54

6.2 Alternator Belt ...................................................................54

6.3 Steering Shaft Adjustment ................................................55

6.4 Armrest Adjustment...........................................................55

6.5 Standard Seat Adjustments ..............................................56

6.6 Premium Seat Option Adjustments...................................56

6.7 Front Proximity Switch ......................................................57

6.8 Fine Adjustment ................................................................57

6.9 Height Of Cut ....................................................................58

6.10 Torque Specification .......................................................59

Maintenance and Lubrication

7.1 Maintenance And Lubrication Charts................................60

7.2 General Precautions .........................................................63

7.3 Engine...............................................................................63

7.4 Engine Lubrication ............................................................64

7.5 Engine Coolant .................................................................65

7.6 Hydraulic System ..............................................................67

7.7 Hydraulic Filter ..................................................................68

7.8 Hydraulic Hoses................................................................69

7.9 Fuel ...................................................................................70

7.10 Air Cleaner ......................................................................72

7.11 Charge The Battery.........................................................72

7.12 Battery.............................................................................73

7.13 Engine Exhaust...............................................................74

7.14 Tires ................................................................................74

7.15 Wheel Mounting Procedure ............................................75

7.16 Blade Change .................................................................75

7.17 Inspecting Blades............................................................76

7.18 Sharpening Blades..........................................................76

7.19 Folding ROPS .................................................................77

7.20 Care and Cleaning..........................................................78

7.21 Mower Storage................................................................79

Electrical System

8.1 General Information ..........................................................80

8.2 Fuse And Relay/Component identification ........................80

Problem Solving

9.1 Engine Problem Solving....................................................82

Quality of Cut

10.1 Quality of Cut Problem Solving .......................................84

10.2 Washboarding.................................................................84

10.3 Step Cutting ....................................................................85

10.4 Scalping ..........................................................................86

10.5 Stragglers........................................................................87

10.6 Streaks............................................................................88

10.7 Windrowing .....................................................................89

10.8 Mismatched Cutting Implements.....................................90

Specifications

11.1 Engine Specification .......................................................91

11.2 Dimensions & Weights....................................................92

11.3 Machine Specification .....................................................94

11.4 Hydraulic Specification....................................................94

11.5 Vibration..........................................................................95

11.6 Noise...............................................................................96

11.7 Slopes .............................................................................96

11.8 Cutting Performance .......................................................96

11.9 Cutter Implement Specification .......................................96

11.10 Recommended Lubricants ............................................97

11.11 Accessories...................................................................97

1 INTRODUCTION

en-2

1Introduction

1.1 IMPORTANT ______________________________________________________________

The AR730 with a Diesel engine is a self propelled rotary mower with hydraulic systems to power the traction drive, the

cutting implement lift and lower, the cutting implement drives and the steering.

IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high level.

This Manual is part of the machine and must stay with the machine always. The suppliers of new, or used, machines

need to keep this documentation and supply the owners with a copy.

This equipment is intended for turf care and maintenance, primarily for grass cutting. Accessories approved by

Jacobsen may support alternate secondary functionality to allow more versatile use of the equipment.

Certifications of accessories for global regional use is subject to local regulations.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the machine that are not approved by the manufacturer. This type of change can

release the manufacturer from the liability for any damage or injury.

Discard worn parts in accordance with all local environment protection regulations. Use the local systems available in

the country where the machine is used, for these recycled materials. When the machine is at its end of life, there are

guidelines in this manual for the removal of the machine from use.

Use only Jacobsen Genuine spare parts to meet the machine type approval regulations specified by the European

Union.

2006/42/EC

These instructions are the Original instructions confirmed by Jacobsen

INTRODUCTION 1

en-3

1.2 PRODUCT IDENTIFICATION _________________________________________________

Mower Serial number plate

A. Maximum front axle load in Kg (for machines being driven on the

highway)

B. Unladen weight, (No cutting implements or fuel (mass) in Kg

C. Maximum rear axle load in Kg (for machines being driven on the

highway)

D. Power in Kw

E. Date code

F. Machine type (Designation)

G. Product code

H. Product name

J. Serial number

Location of Mower Serial number plate

The serial number plate (A) is found on the rear closeout.

Engine Identification

The engine serial number is found on the top of the valve cover toward

the front of the mower. The label shows the engine group and serial

number

The engine serial number is also found on the engine block.

1.3 KEY NUMBERS

Record the mower and the engine serial numbers.

The serial numbers are found on the serial plates and the engine serial

number is on the valve cover.

Machine Serial Number: . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Serial Number: . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4 PARTS MANUAL

To refer to the parts list for this mower you have two options:

1. Website – www.jacobsen.com. Select the “ONLINE PARTS LOOK-UP” tab. These pages will show the parts list

and the line drawings you need to help with the identification of spare parts.

2. Website – www.jacobsen.com. Select the “MANUALS” tab. You have the option to view or “Download” a PDF

version of the parts manual.

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

Rear

Closeout

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

V2403

S/N KEAXXXXX

Contact KEA for Parts

MADE IN JAPAN

1 INTRODUCTION

en-4

1.5 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _______________________

1.5.1 DURING SERVICE LIFE_____________________________________________________

All the used fluids and parts must be controlled as hazardous materials. Recommended procedures must be followed for their

safe removal.

If a fluid leak occurs, contain the spill to make sure that the leak does not flow into the ground or drainage system. Follow the

regulations in force to make sure that leaks are controlled.

The maintenance procedures in this manual make sure that the damage that the machine can cause in the local environment

is controlled.

When the machine completes its full service life, the following actions must be taken.

1.5.2 END OF SERVICE LIFE _____________________________________________________

These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved local waste

disposal and agencies for recycled materials.

• Park the machine in an applicable area to use all of the necessary lifting equipment.

• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical manuals

applicable to the machine.

• Remove and store correctly

1. Batteries

2. Fuel

3. Engine coolant

4. Oils

• Read the Technical Manual before you begin to disassemble the machine. Plan the disassembly, give

attention to parts that are in a state of mechanical pressure or contain stored energy e.g springs.

• Items that continue to have a service life must be separated and returned to the local dealer.

• Items that are worn must be separated into the material groups and removed according to the agencies for

the recycled materials that are available. Common examples.

• Steel

• Non ferrous metals

• Aluminum

• Brass

• Copper

• Plastic materials

• Identified

• Can be recycled

• Can not be recycled

• Not identified

• Rubber

• Electrical and Electronic Components

• Some parts are not easily separated e.g. Hydraulic hoses. These materials must be added to the “General

discarded materials” area.

• Do not burn discarded materials.

Change the machinery records to show that the machine is not in operation and is discarded. Supply this serial number to

The Jacobsen Warranty Department to close their records.

SAFETY 2

en-5

2Safety

2.1 HOW TO OPERATE SAFELY_______________________________________________________

2.1.1 SAFE OPERATION

a Read the Operator’s Manual and other training material. If the operator or technician can not read this manual,

the owner is responsible to describe this material to the operators and technicians. Manuals in additional

languages may be available on the Jacobsen or Ransomes Jacobsen website.

a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the

equipment.

b Children or other people who do not understand these instructions must not use the mower. The local regulations

can limit the age of the operator.

c Never use a mower near bystanders, including children or animals.

d Remember that the operator or owner is responsible for accidents or hazards that occur to other people or their

property.

e Never carry passengers.

f Never allow anyone to operate or service the mower or its attachments without correct instructions.

g Do not operate equipment while tired, sick or after you use alcohol or drugs.

2.1.2 PREPARATION

a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard hat,

safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving parts.

b Do not operate the equipment with the Interlock System disconnected or the system does not operate correctly.

Do not disconnect or prevent the operation of any switch.

c Never operate equipment that is not in correct order or without labels, guards, shields, deflectors or other

protective devices fastened.

d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator coolant

level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the mower.

e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during bad

weather. Never operate the mower with lightning in the area.

f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the job.

Only use parts, accessories and attachments approved by Jacobsen.

g Be careful of holes in the terrain and other hazards that are not visible.

h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be

careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles

(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.

i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you rotate

one blade, other blades can rotate.

WARNING

EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.

Know the location and correct operation of controls. Operators without experience must receive instruction from a

person trained in the correct operation of the equipment before being allowed to operate the mower.

Only use parts, accessories and attachments approved by Jacobsen.

2 SAFETY

en-6

2.1.3 OPERATION

a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the

exhaust fumes can increase to dangerous levels.

b Never carry passengers. Keep bystanders or animals away from the mower.

c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with the

operator in the seat. Never start the engine with anyone standing near the mower.

d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep your

hands and feet away from the cutting implements.

e Do not use on the slopes greater than the safe slope limit for the equipment.

f To guard against over turning or loss of control:

– Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

– Do not start or stop suddenly on slopes.

– Decrease the speed when you operate on slopes or when you must turn. Use caution when you change

direction. Turf condition can change the mower stability.

– Use caution when you operate the mower near drop-offs, ditches or embankments.

– Be careful of holes in the terrain and other hazards that are not visible.

g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not operate

the cutting implements when you drive in the reverse direction.

h Use caution when you go near corners, trees or other objects that can prevent a clear view.

i Equipment must meet the current regulations to be driven on the public roads.

j Before you move across or operate on the paths or roads, turn off the mow switch, lift the mowers and travel at

decreased speed. Look for traffic.

k Stop the blades when the mower is on any surface that is not grass.

l Do not release the cut grass in the direction of bystanders or allow bystanders near the mower while in operation.

m Do not operate the mower with damaged guards or without safety devices in position.

n Do not change the engine governor setting or over-speed the engine. Never change or tamper with adjusters that

are closed with a seal for the engine speed control.

o Before you leave the operator compartment, for any reason:

– Disengage all the drives and lower attachments to the ground.

– Engage the parking brake.

– Stop the engine and remove the key.

p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for damage

and make repairs.

q Decrease the throttle setting before you stop the engine.

r Do not use this equipment for uses that the mower was not made for.

SAFETY 2

en-7

2.1.4 ROPS

a The ROPS is a safety device. Always use the seat belt when you operate a mower equipped with a ROPS. Make

sure the seat belt can be released quickly in an emergency.

b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary. Do not

operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water. There is no

roll over protection with the ROPS in the folded position.

c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other

objects with the ROPS.

d Do not use the seat belt with the ROPS in the folded position.

e Inspect the ROPS for damage. Keep the ROPS hardware fastened.

f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged

ROPS.

g Do not remove the ROPS from the mower.

h Jacobsen must approve any changes to the ROPS.

2.1.5 SAFE HANDLING OF FUELS

a The fuel and the fuel vapors are flammable. Use caution when you add fuel to the mower. The fuel vapors can

cause an explosion.

b Never use containers that are not approved to keep or transfer fuel.

c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of fuel or

fuel vapors.

d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel

container on the ground away from your vehicle before you fill the container.

e Refuel the mower before you start the engine. Never remove the fuel cap or add fuel to the mower when the

engine is in operation or while the engine is hot.

f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.

g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to lock

the fuel nozzle in the open position.

h Do not over fill the fuel tank. Leave at least 1 inch (2.5 cm) below the filler neck.

i Always tighten the fuel tank cap and container cap after you add fuel.

j If the fuel spills on your clothing, change your clothing immediately.

2.1.6 MAINTENANCE AND STORAGE

a Before you clean, adjust or repair this equipment, push mow switch to the OFF position, lower the cutting

implement to the ground, engage the parking brake, stop the engine and remove the key.

b Make sure the mower is parked on a solid and level surface.

c Never work on a mower that is lifted only by a jack. Always use jack stands.

d Never allow anyone to service the mower or its attachments without correct instructions.

e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a positive

mechanical lock is used.

f When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near

flames or drain the fuel inside a building.

2 SAFETY

en-8

g Disconnect the battery before you service the mower. Always disconnect the negative battery cable before the

positive battery cable. Always connect the positive battery cable before the negative battery cable.

h Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To

prevent an explosion, keep any device that can cause sparks or flames away from the battery.

i Disconnect the battery charger from the power supply before you connect or disconnect the battery charger to

the battery. Wear protective clothing and use insulated tools when you service the battery.

j Be careful and wear gloves when you check or service the cutting implement blades. Replace any damaged

blades, do not try to correct a damaged blade.

k Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in operation,

unless the adjustment needs the engine in operation.

l Carefully release the pressure from components with stored energy.

m To prevent injury from hot, high pressure oil, never use your hands to check for oil leaks. Use the paper or

cardboard to find leaks.

n The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your skin, a

doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.

o When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to the

correct torque. Make sure the hydraulic system is in good condition before you start the engine.

p Keep the mower and the engine clean.

q Allow the engine to become cool before storage and always remove the ignition key.

r Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

s Replace worn or damaged parts for safety. Replace damaged or worn labels. Only use parts, accessories and

attachments approved by Jacobsen.

t To decrease the fire hazard, remove grass and other materials that burn from around the engine, muffler, battery

tray and fuel tank area.

u Disconnect the battery and controller connectors before you weld on this mower.

2.1.7 WHEN YOU PUT THE MOWER ON A TRAILER

a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and be able to

carry the weight of the mower.

b Use a trailer with a full-width ramp to load or unload the mower.

c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be sent

down and toward sides of trailer.

d Make sure that all latches are correctly fastened.

SAFETY 2

en-9

2.1.8 IMPORTANT SAFETY NOTES________________________________________________

This safety alert symbol gives a warning of possible hazards.

DANGER - Indicates a dangerous condition that WILL cause death or injury unless it is prevented.

WARNING - Indicates a dangerous condition that CAN cause death or injury unless it is prevented.

CAUTION - Indicates a dangerous condition that can cause injury and property damage unless it is prevented. The

label can indicate work procedures that are not safe.

NOTICE - Indicates a condition that can cause damage to the property unless it is prevented. The label can indicate

work procedures that are not safe.

Some illustrations in this manual show the shields, guards or plates, removed. Do not operate this equipment without

these devices correctly fastened in position.

WARNING

The Interlock System on this mower prevents the operation of the mower unless:

a The parking brake is engaged.

b The mow switch is in the OFF position.

c The traction pedal is in the Neutral position.

The system will stop the engine if the operator leaves the seat without:

a The parking brake engaged.

b The mow switch in the OFF position.

NEVER operate the mower unless the Interlock System operates correctly.

WARNING

1. Before you leave the operator position, for any reason:

a. Return the traction pedal to Neutral.

b. Disengage all drives.

c. Lower the mowers to the ground.

d. Engage the parking brake.

e. Stop the engine and remove the ignition key.

2. Keep your hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the mower.

3. Keep persons and animals away from the area of operation.

4. Never carry passengers.

5. Never operate the equipment without a correctly fastened grass deflector in position.

2 SAFETY

en-10

By following all instructions in this manual, you increase the life of your machine and keep its maximum performance.

Adjustments and maintenance must always be done by an approved technician.

If additional information or if service is needed, contact your Authorized Jacobsen Dealer. Your Dealer knows the

current methods to service this equipment.

WARNING

Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

• Always start and operate the engine in a well-ventilated area.

• If in an enclosed area, vent the exhaust to the outside.

• Do not modify or tamper with the exhaust system

• Do not idle the engine except when necessary.

For more information go to

www.p65warnings.ca.gov/diesel

WARNING

To prevent injury from the hot oil at high pressure, do not use your hands to check for oil leaks. make sure that you

use paper or cardboard.

Release of hydraulic fluid at high pressure has enough force to enter through the skin. if the fluid enters through the

skin, the fluid must be surgically removed within hours by a specialist doctor or gangrene may result.

WARNING

When the machine is driven off-road, a seat belt must be worn at all times.

This warning is because a seat belt must be worn with a ROPS to follow the Machinery Directive,

2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)

Jacobsen recommends that the owner/user of the machine completes a local risk assessment of the machine to find

any conditions that do not follow this rule. e.g. when you drive the machine next to water or on the highway.

WARNING

Explosive gases are released by batteries. The battery contains corrosive acid and supplies an electrical current that

is high enough to cause burn injuries to the body.

WARNING

You must not use this machine to tow other mowers or vehicles.

SAFETY 2

en-11

WARNING

Ear protection must be worn when you operate machines with an operator ear noise level of more than 85 db(a) leq.

WARNING

Vibration Exposure Limits

Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the Daily Exposure

Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to reach the EAV and up to 8

hours/day to reach the ELV.

Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²

Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be taken

Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²

If several tools are used the exposure values must be combined:

Total exposure is then the combined value of the activities

WARNING

Never mow if there is a risk of lightning or when you hear thunder. If you are in the middle of mowing, stop in a safe

place, turn off the engine and go inside a building.

CAUTION

When you do any welding on the machine, the battery, controller and display units must be disconnected before you

start. You must not open the controller. If the controller is opened, this can cancel all of the warranties and can cause

the failure of the machine.

CAUTION

Personal Protective Equipment (PPE), For example safety glasses, leather work shoes or boots, a hard hat, leather

work gloves and ear protection must be used after the owner/user completes a local risk assessment of the mower,

to prevent injury.

Training in all manual operations must be given by an approved person before the machine is used the first time.

3 LABELS

en-12

3Labels

3.1 SAFETY LABELS__________________________________________________________

A 4199140 Warning, hot surfaces. Do not touch with bare hand.

B 4181861 Warning, do not use start assist fluids.

C 4181862 Warning, do not remove the radiator cap when the radiator is hot.

D 4153197 Caution, do not pressure wash radiator or allow water to enter the air intake.

E 9114380 Warning, fasten seat belt when folding ROPS is in the raised position.

F 4181864 Warning, battery

G 4326710 Warning, do not operate on slopes greater than 15°. Read the manual

H 4311249 Warning, implement

– Rotating blades. Keep your hands, feet and clothing away from cutting implements.

– Warning, be careful of objects thrown by the cutting implements. When mower is in operation,

keep bystanders and animals away.

– Read the manual. Do not allow anyone without training to use the mower.

– Do not step on cutting implements.

J 4326718 Warning, mower

– Read the manual. Do not allow anyone without training to use the mower.

– Keep the shields in position and hardware fastened.

– Keep your hands, feet and clothing away from moving parts.

– Before you clean, adjust or repair this equipment, disengage all drives, engage the parking

brake and stop the engine.

– Never carry passengers.

– When mower is in operation, keep bystanders and animals away.

K 845027 To prevent injury when adjusting the height of cut, use caution to prevent your fingers being

pinched between moving and fixed parts of the cutting implement.

4326718

4181861

4181862

4199140

STOP

4181864

15°+

4326710

LABELS 3

en-13

L Warning - This structure’s protective capability may be impaired by structural damage, overturn, or alteration. If

any of these conditions occur, the structure must be replaced.

M Notice - Do not fold this ROPS if a canopy is attached. Damage to the mover hood could result.

N Always use the seat belt with the ROPS frame in the vertical and locked position. Never use the seat belt with the

ROPS in the folded position.

P Canadian EMC Decal

This structure's proctective

capability may be impaired

by structural damage,

overturn, or alteration.

If any of these conditions

occur, the structure must

be replaced.

!WARNING

557844

NOTICE

Do NOT fold this ROPS

if a canopy is attached.

Damage to the mower

hood could result.

3 LABELS

en-14

3.2 INSTRUCTION LABELS

Description

A 4117468 105 dB Guaranteed Sound Power Level

B 4381826 Traction Pedal

C 692776 Front HOC, Right Wing Deck

D 675163 Rear HOC, Right Wing Deck, Left Wing Deck, Left Wing Deck, LH

105dB

LWA

4381826

692776

19 mm 0.75 in 1

25 mm 1.00 in 2

32 mm 1.25 in 3

38 mm 1.50 in 4

44 mm 1.75 in 5

51 mm 2.00 in 6

57 mm 2.25 in 7

64 mm 2.50 in 8

70 mm 2.75 in 9

76 mm 3.00 in 10

83 mm 3.25 in 11

89 mm 3.50 in 12

95 mm 3.75 in 13

102 mm 4.00 in 14

108 mm 4.25 in 15

114 mm 4.50 in 16

15 12

16 13 10

675163

19 mm 0.75 in 1

25 mm 1.00 in 2

32 mm 1.25 in 3

38 mm 1.50 in 4

44 mm 1.75 in 5

51 mm 2.00 in 6

57 mm 2.25 in 7

64 mm 2.50 in 8

70 mm 2.75 in 9

76 mm 3.00 in 10

83 mm 3.25 in 11

89 mm 3.50 in 12

95 mm 3.75 in 13

102 mm 4.00 in 14

108 mm 4.25 in 15

114 mm 4.50 in 16

12 16

CONTROLS 4

en-15

4Controls

4.1 OPERATOR COMPARTMENT ________________________________________________

4.2

4.3

4.4

4.5

4.6

4.7

4.2 - Control Panel

4.3 - Armrest Adjuster

4.4 - Traction Pedal

4.5 - Steering Tilt Lever

4.6 - Tow Valve (Under Seat)

4.7 - Brake Valve (Under Floorboard)

4 CONTROLS

en-16

4.2 CONTROL PANEL _________________________________________________________

4.2.1 - Key Switch

4.2.2 - Parking Brake Switch

4.2.3 - Mow Switch

4.2.4 - Light Switch (Optional)

4.2.5 - Lift/Lower Joystick

4.2.6 - Visual Display

0.0 Hours

4.2.1

4.2.2

4.2.3

4.2.4

4.2.5

4.2.6

CONTROLS 4

en-17

4.2.1 KEY SWITCH _____________________________________________________________

Turn the key switch to the 'START' position to start the engine. When the engine

starts, release the key and allow to return automatically to the 'RUN' position.’

To stop the engine, turn the key to the ‘OFF’ position.

NOTE. There can be a time delay before the engine starts, it depends on the

engine temperature while the glow plugs operate automatically.

4.2.2 PARK BRAKE SWITCH _____________________________________________________

Move the orange button back and press the front of the switch to engage the park brake.

When the engine is stopped, the parkbrake is applied with the switch in both the ON and OFF

position.

To release the park brake, press the rear of the switch.

The park brake icon is displayed on the visual display screen when engaged.

DO NOT apply the brake while the machine is in motion. The park brake will also auto-engage

when the transmission is in neutral & the machine is not in motion. When this function is active,

the brake will automatically release when transmission pedal is operated in order to drive forward or in reverse.

4.2.3 MOW SWITCH ____________________________________________________________

The mow switch engages cutter rotation.

To cut grass, push the front of the switch and move the joystick forward to lower the cutting

implements. When the switch is in the ON position, the red LED on the switch is illuminated.

When the mow switch is in the ON position, the mower traction will be in all wheel drive (AWD).

To stop the drive to the cutting implements, press the rear of the mow switch.

When the cutting implements are lifted or the operator leaves the seat, cutting implements

rotation is stopped.

4.2.4 LIGHT SWITCH____________________________________________________________

Turns the work lights ON and OFF.

Push the top of the switch to turn the lights ON.

Push the bottom of the switch to turn the lights OFF.

OFF

RUN

START

4 CONTROLS

en-18

4.2.5 LIFT/LOWER JOYSTICK ____________________________________________________

The lift/lower joystick controls the lift and lower operation of the cutting

implements. The lift/lower joystick operates in One-Touch or manual

mode. Push the lift/lower joystick to lower the cutting implements or pull

the lift/lower joystick to lift the cutting implements.

The One-Touch or manual mode is set on the display.

Manual Mode - When One-Touch is disabled, the cutting implements will

lift or lower only while the lift/lower joystick is pulled or pushed.

One-Touch Mode - With One-Touch enabled and the mow switch is in

the ON position,

To Lower - Push and release the lift/lower joystick once to lower the

cutting implements to the mid Cross Cut position, Push and release the

lift/lower joystick a Second time to lower the cutting implements to the

ground and start the blades.

To Raise - Pull and release the lift/lower joystick once to lift the cutting implements to the mid Cross Cut position.Pull

and release the lift/lower joystick a second time to completely lift the cutting implements and stop the blades.

Left Wing Button - Press the left wing button on the top of the joystick to enable the left wing cutting implement. The

light on the button will turn on and the joystick will control the lift and lower of the cutting implement. When the left wing

cutting implement is lowered, and the mower is moving, the cutting implement blades will start to turn

Press the left wing button a second time to disable the left wing cutting implement. The cutting implement will stop and

lift to the transport position.

Right Wing Button - Press the right wing button on the top of the joystick to enable the right wing cutting implement.

The light on the button will turn on and the joystick will control the lift and lower of the cutting implement. When the right

wing cutting implement is lowered, and the mower is moving, the cutting implement blades will start to turn

Press the right wing button a second time to disable the right wing cutting implement. The cutting implement will stop

and lift to the transport position.

To engage the cutting implements if they are already in the lowered position but disengaged, Press the Mow Switch to

On position, Push and release the Lift /Lower joystick once to engage the cutter blades.

4.2.6 VISUAL DISPLAY__________________________________________________________

The visual display is activated when the key switch is turned to the ‘RUN’ position.

Left Wing

Button Right Wing

Button

CONTROLS 4

en-19

4.2.6.1 STARTUP SCREEN _______________________________________________________

When the key switch is turned to the ‘RUN’ position, this screen is shown for

two seconds.

The hour meter will show total hours of engine operation.

4.2.6.2 WARNING / SERVICE SCREEN _____________________________________________

After the startup screen the warning screen is shown. The warning screen is

visible for three seconds. If there is no input needed, the main screen will

become visible. If a fault condition has occurred during the previous start, a

pop up screen will become visible over the top of the warning screen. The

operator must confirm the fault before they can move to the main screen.

0.0 Hours0.0 Hours

WARNING

If incorrectly used this maching can cause

severe injury. Those who use and maintain this

machine should be trained in its proper use,

warned of its dangers and should read the

entire operators manual before attempting to set

up, operate, adjust or service the machine.

4 CONTROLS

en-20

4.2.6.3 ICONS _________________________________________________________________

The following Icons are used in the controller. Not all icons may be visible, depending on the engine and the options

installed on the mower.

4.2.6.4 FIRST SCREEN __________________________________________________________

This screen shows the status of vehicle functions, the fuel gauge and coolant

temperature gauge.

When an icon is grayed out, the mower function is not active or the switch is in

the OFF position.

Color icons indicate an active function or switch in the ON position.

The fuel gauge is on the left side of the screen.The fuel gauge color will be

green when the tank is between 30% and 100% full. The fuel gauge color will

be orange when the tank is between 18% and 29% full. The gauge color will

be red when the tank is less than 18% full. Do not allow the mower to run out

of fuel.

The engine temperature gauge is on the right side. The temperature gauge color will be green with engine temperature

below 203° F (95° C). The temperature gauge color will be orange with the engine temperature between 203° F (95° C)

and 220° F (104° C). The temperature gauge color will be red with the engine temperature above 220° F (104° C).

MODE

TST

™

TST

™

OFF Not

Required

ON Required Inhibited OFF ON No Yes

Not In

Neutral

Neutral System Date

and Time

Parking Brake

Switch Parked Regen Mow Switch Traction Pedal Engine Start

Weight Transfer

OFF Active OFF Active OFF Active OFF Active OFF Active

OFF Active OFF Active

Fuel

Gauge

Temperature

Gauge

Glow Plugs High Exhaust

Temperature Alert

Check Engine

Alert

Water In Fuel

Alert

Cruise Control

OFF Active OFF Active

TST Throttle Mode Menu System

Navigation

Garage Manual Home Back Select Menu

Select

Taskbar Popup Menu

Cruise

Control

Throttle

Mode

Weight

Transfer

4WD Fan

Control

Auto

12:00:00 1/1/2016

0.0 Hours

TST

™

CONTROLS 4

en-21

4.2.6.5 ENGINE START __________________________________________________________

When the key switch is turned to the start position and the interlocks are set,

this screen is shown.

To start the engine, the parking brake switch must be in the ON position, the

mow switch must be in the OFF position and the traction pedal must be in the

Neutral position. There may be a time delay before the engine starts to rotate,

it depends on the engine temperature while the glow plugs operate

automatically.

4.2.6.6 THE ENGINE WILL NOT START _____________________________________________

When the ignition key is turned to the start position and the interlocks are not

set, this screen is shown.

• The parking brake switch is not in the ON position. The icon will flash

red and gray.

• The mow switch is not in the OFF position. The icon will flash red and

gray.

• The traction pedal is not in the Neutral position. The icon will flash

yellow and gray.

The engine will not start until all the items in the list are correct.

4 CONTROLS

en-22

4.2.6.7 TASKBAR POP-UP MENU _________________________________________________

When the first screen is shown on the display, press any of the selection

buttons to display the Taskbar Pop-Up Menu. If the reversing fan option is

installed, press the LEFT or RIGHT arrow keys to toggle to the second

screen.

To activate cruise control, drive the mower in the forward direction, press any

of the selection buttons to display the taskbar pop-up menu, press the first

selection button from the left and lift your foot off the pedal. The cruise control

icon will change to blue and the mower will continue to drive at the current

speed until cruise control is selected again, the traction pedal is pressed, the

brake switch is moved to the ON position, the operator leaves the seat or the

key switch is turned to the OFF position.

To engage 4WD, press any of the selection buttons to display the Taskbar

Pop-Up Menu and press and hold the second button from the left. 4WD will be

active as long as the button is held down and the mower is driven in the

forward direction. When the button is released, the mower will return to 2WD.

To change throttle mode, press any of the selection buttons to display the

Taskbar Pop-Up Menu and press the third button from the left. The throttle

mode icon on the display will cycle to the next mode. Repeat pushing the

throttle mode button until the desired traction mode is selected. Throttle mode

can also be changed using the vehicle settings menu. See “Throttle Mode”

on page 25.

To activate the weight transfer system, press any of the selection buttons to

display the Taskbar Pop-Up Menu and press and hold the fourth button from

the left. The mower controller will pulse the lift system to transfer the weight

from the cutting implements to the drive wheels to increase traction for as long

as the button is held down. When the button is released, the mower will return

to normal operation.

If the reversing fan option is installed, press the LEFT or RIGHT arrow

keys to toggle to the second screen and press the first selection button from

the left. The fan will complete a reverse fan cycle then return to normal

operation.

TST

™

12:00:00 1/1/2016

0.0 Hours

Selection

Buttons

Selection

Buttons

TST

™

MODE

TST

™

Cruise

Control

Throttle

Mode

Weight

Transfer

4WD

Fan

Reverse

CONTROLS 4

en-23

4.2.6.8 MAIN MENU _____________________________________________________________

When the first screen is shown on the display, press the LEFT or RIGHT

arrow keys to access the main menu.

4.2.6.9 MENU NAVIGATION_______________________________________________________

When the first screen is shown on the display, press the LEFT or RIGHT

arrow keys to access the main menu.

Use the UP and DOWN arrow keys to move the selection

arrow up or down the list.

Press the select button to select menu item indicated by the arrow.

Press the back button to return to the previous screen.

Press the home button to return to the first screen.

The main menu has Language, Clock, Display Settings, Vehicle Settings

(Requires PIN), Service and Manual Throttle.

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

Back

Button

Home

Button

Arrow

Keys

Select

Button

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

4 CONTROLS

en-24

4.2.6.10 LANGUAGE ____________________________________________________________

Press the LEFT or RIGHT arrow keys to display the main menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Language. Press the select button to select Language.

Use the UP and DOWN arrow keys until the green arrow is

next to the needed language.

Press the select button to select the language.

Press the back button to return to previous menu.

4.2.6.11 CLOCK ________________________________________________________________

Press the LEFT or RIGHT arrow keys to display the main menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Clock. Press the select button to select Clock.

The  is moved with the UP and DOWN arrow keys to select,

date, time or date format.

The button accepts the option that has the .

Use the UP and DOWN arrow keys to increase or decrease

the value.

Use the LEFT or RIGHT arrow keys to move between fields.

Press the select button to set.

Press the button to return to previous menu.

English

Deutsch

Français

Svenska

Nederlands

Español

Nihongo

Main Menu

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

Clock Settings

Set Date/Time

2:27:14 PM 09/27/18

Set Date Format

US EU

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

CONTROLS 4

en-25

4.2.6.12 DISPLAY SETTINGS _____________________________________________________

Press the LEFT or RIGHT arrow keys to display the main menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Display Settings. Press the select button to select Display Settings.

Press the select button to set.

Press the button to return to previous menu.

4.2.6.13 VEHICLE SETTINGS MENU _______________________________________________

Press the LEFT or RIGHT arrow keys to display the main menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Vehicle Settings. Press the select button to select Vehicle Settings.

The vehicle settings menu has the Throttle Mode, Measure Units and PIN.

Brightness

Display Settings

Use Up/Down to toggle Auto Brightness

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

Mode

Measurement Settings

Vehicle Settings Menu

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

4 CONTROLS

en-26

4.2.6.14 THROTTLE MODE_______________________________________________________

Navigate to the Vehicle Settings Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Mode. Press the select button to select Mode.

There are three modes, Automatic (A), Manual (M) and Garage. The mode

selection can only be changed when the machine is stopped.

Automatic Mode (A) - Automatic throttle and drive features enabled.

• Climb assist - Load sensing system adjusts engine throttle and

ground speed for efficient slope climbing

• Cut assist - Load sensing system adjusts engine throttle and ground

speed to maintain optimum cutting performance

• Auto Idle - Throttle drops to idle when pedal returns to neutral during

transport operations,

Garage Mode - The cutting system is disabled, engine operates at 20%

throttle and max speed limited to 5 mph (8km/h) for safe, controlled use in

workshops, storage facilities and when loading onto vehicles

Manual Mode (M) - The engine speed is set at a fixed value that can be

changed using the Manual Throttle menu.

4.2.6.15 MEASURE UNITS _______________________________________________________

Navigate to the Vehicle Settings Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Measure Units. Press the select button to select Measure Units.

Use the arrow keys to change the unit of measure. The speed unit of measure

can be set to either Mph or Km/h. The temperature unit of measure can be set

to either °F (Fahrenheit) or °C (Celsius).

Automatic

Garage

Manual

Mode Setting

Mode

Measurement Settings

Vehicle Settings Menu

Speed MPH

Temperature °F

Measurement Units Settings

Mode

Measurement Settings

Vehicle Settings Menu

CONTROLS 4

en-27

4.2.6.16 ENTER PIN _____________________________________________________________

Start the engine. Navigate to the Vehicle Settings Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to PIN. Press the select button to select PIN.

Use the arrow keys to highlight the correct number. Press the select button

to enter the number and to advance to the next position. Repeat until all four

numbers of the pin have been entered.

Highlight the C and press the select button to clear the previous number.

If the correct PIN number has been entered the PIN menu will be on the

display.

The initial PIN number is 1001

Notice: Managers are advised to change the PIN to stop the machine

parameters being changed.

1001

123

456C

7890

Enter Pin

Mode

Measurement Settings

Vehicle Settings Menu

One Touch

AWD in Mow

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

4 CONTROLS

en-28

4.2.6.17 SERVICE MENU ________________________________________________________

Press the LEFT or RIGHT arrow keys to display the main menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Service. Press the select button to select Service.

The Service Menu has the Fault Log, Time Until Service, Vehicle Status, I/O

Diagnostics, Inhibit Regen and Parked Regen.

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

CONTROLS 4

en-29

4.2.6.18 FAULT LOG ____________________________________________________________

Navigate to the Service Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Fault Log. Press the select button to select Fault Log.

The last 50 “Faults” that the controller finds are recorded. When 50 faults are

recorded, the fault that next occurs will write over the oldest fault.

The inclinometer records faults when the mower is operated on slopes greater

than 22°.

The engine controller records the engine shut down faults because of

overheat or loss of oil pressure.

The mower controller records hydraulic by-pass fault and missed service.

Press the button to select, press the UP and DOWN arrow

keys to move the green arrow . The errors will move with the last error at

the top of the screen.

Select the fault log to be accessed and accept to show the details.

These details show the date and time of the fault.

Press the back button to return to previous menu.

402.6 Hours

234.1 Hours

137.5 Hours

Fault Log

Engine Overheat Fault

Date 08/27/2018

Time 2:23 PM

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

4 CONTROLS

en-30

4.2.6.19 TIME UNTIL SERVICE____________________________________________________

Navigate to the Service Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Time Until Service. Press the select button to select Time Until

Service.

Press the back button to return to previous menu.

To reset the service hours, access the Pin Menu and select Reset Service

Hours.

4.2.6.20 VEHICLE STATUS _______________________________________________________

Start the engine. Navigate to the

Service Menu.

Use the UP and DOWN

arrow keys until the green

arrow is next to Vehicle Status.

Press the select button to select

Vehicle Status.

The first screen of the vehicle status

shows the software revisions of the

MCU controller and display.

The second screen of the vehicle

status shows the engine speed,

engine throttle position, traction pedal

position and vehicle speed.

The third screen of the vehicle status

shows the battery voltage and the

engine coolant temperature.

Press the back button to return to

previous menu.

Time Until Service

23 Hours

Engine Hours: 202

Cutter Hours: 151

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

Engine Speed

2000

Pedal Position Engine Throttle

2.5 65

Pg 1 of 3

Volts

RPM

Battery Voltage

12.4

Engine Coolant Temperature

141.3

Pg 2 of 3

Volts

°F

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

Controller Software Revision:

011991$A

Display Software Revision:

012001$A

Pg 3 of 3

Vehicle Status

CONTROLS 4

en-31

Software Revision is used by Dealer for fault diagnostics.

4.2.6.21 I/O DIAGNOSTICS _______________________________________________________

Start the engine. Navigate to the Service Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to I/O Diagnostics. Press the select button to select I/O Diagnostics.

Use the UP and DOWN arrow keys until the red arrow is next

to connector you want to check the status of. Press the select button to

select the connector.

4.2.6.22 CONNECTOR J1 ________________________________________________________

This screen shows the status of the J1 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

I/O Diagnostics

DEUTSCH DT13-12PA

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

Connector J1

J1-1 Battery [V ] 12.7

J1-2 Switched 12V

J1-3

J1-4 Battery [V ]

J1-5 Switched 12V

J1-6 Start w/Interlocks

J1-7 CAN Shield

J1-8 CAN Low

J1-9 CAN High

J1-10 Main Ground

J1-11 5V Sensor Output

J1-12

O

4 CONTROLS

en-32

4.2.6.23 CONNECTOR J2 ________________________________________________________

This screen shows the status of the J2 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

4.2.6.24 CONNECTOR J3 ________________________________________________________

This screen shows the status of the J3 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

4.2.6.25 CONNECTOR J4 ________________________________________________________

This screen shows the status of the J4 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

Connector J2

J2-1 Center Lower Solenoid

J2-2 Right Wing Enable Solenoid

J2-3 Center Lift Solenoid

J2-4 Fan Direction

J2-5 Park Brake Solenoid

J2-6 Run w/ Interlocks

J2-7 EDC FWD (mA)

J2-8 EDC REV (mA)

J2-9 Wing Pressure Enable Solenoid

J2-10 Fan Speed (%)

J2-11 Float Solenoid

J2-12 Weight Transfer Pressure Solenoid

O

Connector J3

J3-1

155.5

J3-2 Engine Coolant Temperature

J3-3

J3-4

J3-5 Fuel Sender (%)

J3-6

J3-7 Right Wheel Speed Input

J3-8 Left Wheel Speed Input

J3-9 Signal Ground

J3-10

J3-11 Pedal 1 Input (V)

J3-12 Pedal 2 Input (V)

O

Connector J4

J4-1 Seat Switch O

J4-2 Center Prox/Cross Cut

J4-3 Left Wing Prox

J4-4 Right Wing Prox

J4-5 Hydraulic Oil Level

J4-6

J4-7 Start Switch

J4-8 Park Brake Switch

J4-9 PTO (Mow) Switch

J4-10

J4-11 Left Wing Enable

J4-12 Right Wing Enable

O

CONTROLS 4

en-33

4.2.6.26 CONNECTOR J5 ________________________________________________________

This screen shows the status of the J5 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

4.2.6.27 CONNECTOR J6 ________________________________________________________

This screen shows the status of the J6 connector circuits.

Press the left side button to return to I/O diagnostics menu.

Values are shown for illustration purposes only.

Connector J5

J5-1 Right Wing Mow Solenoid

O

J5-2 Center Mow Solenoid

J5-3 Wing Mow Enable Solenoid

J5-4 Left Wing Enable Solenoid

J5-5 Left Wing Mow Solenoid

J5-6 Wing Lower Solenoid

J5-7 4WD Solenoid

J5-8 Glow Plug

J5-9

J5-10 Joystick Lower

J5-11 Joystick Lift

J5-12 Pump Pressure Switch

O

Connector J6

J6-1

O

J6-2 AWD Solenoid

J6-3 Weight Transfer Solenoid

J6-4

J6-5

J6-6 Battery

J6-7 Battery

J6-8 Water in Fuel

J6-9 Ground

J6-10 Hydraulic Filter Switch

J6-11 Engine Oil Pressure

J6-12

O

4 CONTROLS

en-34

4.2.6.28 INHIBIT REGEN_________________________________________________________

Start the engine. Navigate to the Service Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Inhibit Regen. Press the select button to select Inhibit Regen.

Use the UP and DOWN arrow keys until the red arrow is next

to Enable or Disable. Press the select button to accept

When the Regen Inhibit is selected, the engine can not enter the Active or

Parked Regen states. Inhibit Regen does not prevent Passive Regen. If the

fuel tank is near empty, select the Inhibit Regen until the fuel tank has been

filled.

NOTICE

If the Regen cycle is prevented for too long of a period, a blockage of the

Diesel Particulate Filter (DPF) can occur. If a blockage of the DPF has

occurred, an authorized Kubota Engine Service Center must clean the

DPF before the mower is used.

Disable

Enable

Inhibit Regen

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

CONTROLS 4

en-35

4.2.6.29 PARKED REGEN ________________________________________________________

When a parked regen is required, the parked regen icon will be active on the

display.Start the engine. Navigate to the Service Menu.

Use the UP and DOWN arrow keys until the green arrow is

next to Parked Regen. Press the select button to select Parked Regen.

On the confirmation screen, press the select button to accept and enter

Parked Regen

To start a parked regen, the parking brake switch must be in the ON position,

the mow switch must be in the OFF position and the engine temperature must

be above 150° F (65° C). If these conditions are not met, a screen will appear

indicating the requirements.

When the requirements are met, the mower will enter the parked regen state.

The length of time that the Parked Regen will take depends on the level of

particulate matter in the DPF. During the Parked Regen, the Regen Request

icon will be active. When high-exhaust temperatures are sensed during

Parked Regen, the High-Exhaust Temperature icon will also be active. Do not

disengage the parking brake, stop the engine or move the mower during the

Parked Regen.

WARNING

During Active or Parked Regen, the temperature of the exhaust

components can be more than 1150° F (625° C). To prevent burns, do not

touch a hot exhaust system and do not stand or reach into exhaust gas

area from exhaust pipe outlet. To prevent fires, make sure the engine area

is kept clean and the grass clippings are not near exhaust components.

Make sure the exhaust gas from the exhaust pipe is not blocked and there

is enough space between the exhaust pipe and objects. Park the mower on

concrete or gravel during Parked Regen. During Active or Parked Regen

exhaust gas from the exhaust pipe can cause turf damage or fire.

Confirm to activate Parked Regeneration

Parked Regeneration

Fault Log

Time Until Service

Vehicle Status

I/O Diagnostics

Inhibit Regen

Parked Regen

Service Menu

150° F

Parked Regeneration

Parked Regeneration has been activated

Parked Regeneration

4 CONTROLS

en-36

4.2.6.30 MANUAL THROTTLE ____________________________________________________

Use the UP and DOWN arrow keys until the green arrow is

next to Manual Throttle. Press the select button to select One Touch.

Use the UP and DOWN arrow keys increase or decrease the

engine throttle in 1% increments. Press the select button to accept.

NOTE: The engine speed will only increase or decrease when throttle mode is

set to Manual Mode. This setting does not affect Automatic or Garage mode.

Press the back button to return to previous menu.

4.2.6.31 ONE TOUCH ___________________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to One Touch. Press the select button to select One Touch.

Use the UP and DOWN arrow keys until the green arrow is

next to Enable or Disable. Press the select button to accept.

Disable - The cutting implements lift or lower only while the lift/lower joystick is

pushed or pulled.

Enable - Joystick is pressed and released to lower the cutting implements or

to lift the cutting implements.

Press the back button to return to previous menu.

Manual Throttle 64%

Manual Throttle Settings

Language

Clock

Display Settings

Vehicle Settings

Service

Manual Throttle

Main Menu

Disable

Enable

One Touch

AWD in Mow

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

CONTROLS 4

en-37

4.2.6.32 VEHICLE SPEED ________________________________________________________

Navigate to the PIN Menu.See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Vehicle Speed. Press the select button to select Vehicle Speed.

The button accepts the speed that has the green arrow .

Use the UP and DOWN arrow keys to increase or decrease

the value by 0.5 Mph (0.3 km/h) increments.

Press the select button to set.

Maximum transport speed can be set between 1 - 12 Mph (1.6 - 19.3 km/h)

Maximum mow speed can be set between 1 - 7 Mph (1.6 - 11.3km/h)

Maximum turn speed can be set between 1 - 7 Mph (1.6 - 11.3km/h)

Maximum reverse speed can be set between 1 - 5 Mph (1.6 - 8 km/h)

Press the button to return to previous menu.

4.2.6.33 CHANGE PIN ___________________________________________________________

Navigate to the PIN Menu.See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Change PIN. Press the select button to select Change Pin.

Use the arrow keys to highlight the new correct number. Press the select

button to enter the number and to advance to the next position. Repeat

until all four numbers of the pin have been entered.

Select . To accept.

Some pin numbers are reserved by the controller and cannot be used. A

Jacobsen Dealer or service technician call is required to reset a forgotten pin.

Press the back button to return to previous menu.

One Touch

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

Transport 12.0 Mph

Mow 7.0 Mph

Turn 7.0 Mph

Reverse 5.0 Mph

Max Speed Menu

One Touch

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

123

456C

7890

Change Pin

4 CONTROLS

en-38

4.2.6.34 INCLINOMETER ________________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Inclinometer. Press the select button to select Inclinometer.

Use the UP and DOWN arrow keys until the green arrow is

next to Enable or Disabled. Press the select button to accept.

Press the back button to return to previous menu.

4.2.6.35 SET DEFAULT PARAMETERS

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Set Default Parameters. Press the select button to select Set

Default Parameters.

Press the select button for five seconds to reset the mower to default

parameters.

NOTE: Some parameters below may not apply, depending on options

installed on the mower.

Default Parameters

Speed Units - MPH Transport Speed - 12 MPH

Temperature Units - °F Mow Speed - 7 MPH

Date Format - MM/DD/YYYY Turn Speed - 7 MPH

One Touch - Enabled Reverse Speed - 5 MPH

Brightness - 100% Manual Throttle - 75%

Reversing Fan Mode - Automatic Garage Throttle - 30%

Reversing Fan Duration - 10 Seconds Transport/Mow Throttle - 100%

Reversing Fan Interval - 30 Minutes Start Throttle - 50%

Weight Transfer - Enabled Idle Throttle - 0%

Inclinometer - Enabled

AWD in Mow - Enabled

Press the back button to return to previous menu.

Disabled

Enabled

Tilt Sensing Technology

One Touch

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

One Touch

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

PIN Menu

Hold confirmation button for 5 seconds

to reset to default settings

Reset To Defaults

CONTROLS 4

en-39

4.2.6.36 FAN DRIVE _____________________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Fan Drive. Press the select button to select Fan Drive.

Use the UP and DOWN arrow keys until the green arrow is

next to the desired Fan Drive mode. Press the select button to select the

Fan Drive mode and enter the setting screen.

• Off - Fan will only operate in the normal direction. A manual fan cycle

will not start if selected on the Taskbar Pop-Up Menu.

• Manual - Reversing fan operation must be initiated using the Taskbar

Pop-Up menu. Fan duration time is set in the Manual Fan Drive Setting

screen.

• Automatic - Fan will operate in the normal direction for the interval

time cycle, then operate in the reverse direction for the duration time

cycle. The time cycles will automatically repeat. Using the Taskbar

Pop-Up menu to initiate a manual reversing fan cycle will restart the

interval time cycle after the reverse duration cycle is completed. Fan

duration and interval cycle times are set on the Automatic Fan Drive

Setting screen

To set the duration cycle time (Manual and Automatic), Use the UP

and DOWN arrow keys until the green arrow is next to Duration,

Press the select button to change the duration time setting.

Use the UP and DOWN arrow keys to increase or decrease

the duration time by 1 second. Duration time can be set between 5 and 30

seconds. Press the select button to set the duration time.

To set the interval cycle time (Automatic only), Use the UP and DOWN

arrow keys until the green arrow is next to Interval, press the select

button to change the interval time setting.

Use the UP and DOWN arrow keys to increase or decrease

the interval time by 15 minutes. The interval time can be set between 15,30,40

and 45minutes. Press the select button to set the duration time.

Press the back button to return to previous menu.

Dynamic Debris Clearing

The machine will run an automatic Dynamic Debris Clearing Cycle. Every 5

min of engine run time, the cooling fan will automatically reduce in speed for a

period of 6 seconds, then return to full Fan speed. This is designed to keep

the air intake area of hood clear of debris. This function will run in all vehicle

modes.

Vehicle Speed

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

Weight Transfer Pressure

PIN Menu

OFF

Manual

Automatic

Reversing Fan Menu

Duration

10 Sec

Reversing Fan Menu

Duration

Interval

Sec

Min

Reversing Fan Menu

4 CONTROLS

en-40

4.2.6.37 WEIGHT TRANSFER_____________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Weight Transfer Pressure. Press the select button to select Weight

Transfer Pressure.

Press the select button to disable or enable the weight transfer pressure.

Press the back button to return to previous menu.

4.2.6.38 AWD IN REVERSE_______________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to AWD in Mow. Press the select button to select AWD in Mow.

Press the select button to disable or enable the AWD in Mow function.

Press the back button to return to previous menu.

When AWD in Mow is enabled, the AWD solenoid will be engaged when the

mow switch is enabled and pedal not in reverse. In AWD mode, the maximum

theoretical traction speed obtainable is 6mph.

When AWD in Mow is disabled, the AWD solenoid will not be engaged when

the mow switch is enabled. This allows the operator to mow in 2WD mode,

where the 7mph mow speed limit is obtainable.

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

Weight Transfer Pressure

Reset Service Hours

PIN Menu

Disable

Enable

Weight Transfer Pressure

One Touch

AWD in Mow

Vehicle Speed

Change PIN

TST

Set Default Parameters

PIN Menu

Disable

Enable

AWD in Mow

CONTROLS 4

en-41

4.2.6.39 RESET SERVICE HOURS _________________________________________________

Navigate to the PIN Menu. See 4.2.6.16

Use the UP and DOWN arrow keys until the green arrow is

next to Set Default Parameters. Press the select button to select Reset

Service Hours.

NOTE: Only reset the service hours after the required service has been

performed on the mower. Failure to complete required service can void the

mower’s warranty.

Press the select button for five seconds to reset the service hours.

Press the back button to return to previous menu.

WARNINGS

4.2.6.40 WARNING SLOPE ANGLE - ANGLE ALERT __________________________________

During work if the machine is driven on a slope greater than 16° the screen

will display this warning. This over rides all other information, and will continue

until the machine has been driven to an area with a slope of less than 13°.

The engine will stop if a slope angle of 42° is achieved.

NOTICE

The number in the top right of the screen indicates the total number of current faults recorded. If more than one fault,

it will cycle all current faults.

Change PIN

Inclinometer

Set Default Parameters

Fan Drive

Weight Transfer Pressure

Reset Service Hours

PIN Menu

Hold confirmation button for 5 seconds

to reset current Service Hours

Main Menu

12:00:00 1/1/2016

0.0 Hours

TST

™

Incline is 16°.

Approaching Unsafe Angle.

1/1

4 CONTROLS

en-42

4.2.6.41 WARNING OIL-PRESSURE FAULT _________________________________________

When this screen is shown, the engine oil pressure has decreased below the

normal level. The LED will flash and the horn will sound every four seconds.

If this happens during operation, Stop the engine and check the oil level. Top

up if necessary. If the problem persists consult your service dealer.

4.2.6.42 WARNING ENGINE OVERHEAT____________________________________________

When this screen is shown, the engine temperature has risen above the

normal levels. The LED will flash and the horn will sound two times every two

seconds.

Park the machine in a safe area disengage cutting implements, set engine to

idle to allow engine temperature to decrease prior to switching off the engine.

Clean the radiator and screens of all grass and debris.

The Mow solenoid and joystick lower function is disabled until warning is

cleared.

4.2.6.43 WARNING HYDRAULIC OIL FILTER ________________________________________

This screen is shown when the hydraulic oil filter needs to be replaced. The

LED will flash and horn will sound five times every five seconds.

Return the machine to the service area and replace the filter.

The Mow solenoid and joystick lower function is disabled until warning is

cleared.

4.2.6.44 CLEAN DPF ASH _______________________________________________________

When this screen is shown, the engine controller (ECU) is reporting that the

level of ash in the DPF (Diesel Particulate Filter) is in excess of 95% and

therefore requires servicing. Contact your local Jacobsen dealer for

information on the procedure for servicing the DPF.

12:00:00

0.0 Hours

TST

™

Engine Oil Pressure Fault

1/1

12:00:00 1/1/2016

0.0 Hours

TST

™

Engine Overheat Fault

1/1

12:00:00

0.0 Hours

TST

™

Hydraulic Oil Filter Fault

1/1

12:00:00

0.0 Hours

TST

™

1/1

Clean DPF Ash

1/1

CONTROLS 4

en-43

4.2.6.45 WARNING HYDRAULIC OIL LEVEL _________________________________________

This screen is shown if the hydraulic oil level is low. The LED will flash and

horn will sound six times every six seconds.

Stop the machine immediately and check for oil leaks.

The Mow solenoid and joystick lower function is disabled until warning is

cleared.

4.2.6.46 WARNING BRAKE/TRACTION PEDAL ______________________________________

This screen is shown if the traction pedal is pressed with the parking brake

switch in the ON position. The LED will flash four times every two seconds

and the horn will sound constantly until the traction pedal is returned to the

Neutral position or the parking brake switch is moved to the OFF position.

Remove your foot from the traction pedal and disengage the parking brake

before you drive the mower.

4.2.6.47 WARNING ECU CAN TIMEOUT ____________________________________________

This screen is shown if there is no CAN communication from the ECU for 3

seconds. The LED will flash and the horn will sound two times every five

seconds.

Stop the machine as soon as possible and contact your service dealer. Check

the controller harness connections.

4.2.6.48 WARNING MCU CAN TIMEOUT ____________________________________________

This screen is shown if there is no CAN communication from the MCU for 3

seconds. The LED will flash and the horn will sound two times every five

seconds.

Stop the machine as soon as possible and contact your service dealer. Check

the controller harness connections.