Yamaha RX-V730 Manual de usuario

Marca: Yamaha

Modelo: RX-V730

Categoría: Receptores AV

Tipo: Manual de usuario

OWNER’S MANUAL

RX-V730

AV Receiver

0100V730(U)-cv1 12/27/01, 2:16 PM1

I CAUTION

SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

0101V730_Cau_EN(U) 12/27/01, 2:16 PM2

SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers only)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its

normal operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/

NFPA 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode.

0101V730_Cau_EN(U) 12/27/01, 2:16 PM3

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

left and right, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

–

Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

III CAUTION

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

0101V730_Cau_EN(U) 12/27/01, 2:16 PM4

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Checking the package contents ................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................ 4

Remote control .......................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

PREPARATION

SPEAKER SETUP ................................................. 9

Speakers .................................................................... 9

Speaker placement .................................................... 9

Connecting the speakers .......................................... 10

CONNECTIONS .................................................. 13

Before connecting components ............................... 13

Connecting video components ................................ 14

Connecting audio components ................................ 16

Connecting the antennas ......................................... 17

Connecting an external amplifier ............................ 18

Connecting an external decoder .............................. 18

Connecting the power supply cords ........................ 19

Turning on the power .............................................. 19

ON-SCREEN DISPLAY (OSD) .......................... 20

OSD modes ............................................................. 20

Selecting the OSD mode ......................................... 20

SPEAKER MODE SETTINGS .......................... 21

ADJUSTING SPEAKER OUTPUT LEVELS .. 22

Before you begin ..................................................... 22

Using the test tone ................................................... 22

BASIC OPERATION

BASIC PLAYBACK ............................................ 24

Input modes and indications .................................... 26

Selecting a sound field program .............................. 27

DIGITAL SOUND FIELD PROCESSING

(DSP) ................................................................. 30

Understanding sound fields ..................................... 30

Hi-Fi DSP programs ................................................ 30

CINEMA-DSP ...................................................... 31

Sound design of CINEMA-DSP ............................. 31

CINEMA-DSP programs ........................................ 33

TUNING ................................................................ 35

Automatic and manual tuning ................................. 35

Presetting stations .................................................... 36

Tuning in to a preset station .................................... 38

Exchanging preset stations ...................................... 38

SLEEP TIMER ..................................................... 39

Setting the sleep timer ............................................. 39

Canceling the sleep timer ........................................ 39

RECORDING ....................................................... 40

ADVANCED OPERATION

SET MENU ........................................................... 41

Adjusting the items on the SET MENU .................. 41

1 SPEAKER SET (speaker mode settings) ............ 42

2 LFE LEVEL ........................................................ 44

3 SP DLY TIME (speaker delay time) ................... 44

4 D. RANGE (dynamic range) ............................... 45

5 L/R BALANCE (balance of the main left and

right speakers) ..................................................... 45

6 HP TONE CTRL (headphone tone control) ........ 45

7 INPUT RENAME ............................................... 45

8 I/O ASSIGN (input/output assignment) .............. 46

9 INPUT MODE (initial input mode) .................... 46

10DISPLAY SET .................................................... 46

11MEM. GUARD (memory guard) ........................ 47

REMOTE CONTROL FEATURES ................... 48

Control area ............................................................. 48

Setting the manufacturer code ................................. 49

Changing the source name in the display window .. 50

Clearing renamed source names, and setup

manufacturer codes ............................................. 51

Controlling other components ................................. 52

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ....................................................... 53

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING .......................................................... 54

What is a sound field? ............................................. 54

Sound field program parameters ............................. 54

Changing parameter settings ................................... 55

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS .............................................. 56

TROUBLESHOOTING ...................................... 60

GLOSSARY .......................................................... 64

SPECIFICATIONS .............................................. 66

0102V730_1-8_EN(U) 12/27/01, 2:16 PM1

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “ES” and “DTS Digital Surround” are trademarks of

Digital Theater Systems, Inc.

FEATURES

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω)

Main: 75 W + 75 W

Center: 75 W

Rear: 75 W + 75 W

Rear center: 75 W

Multi-mode digital sound field

processing

◆ Dolby Pro Logic/Dolby Pro Logic decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES compatible decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (Preset

editing)

Other features

◆ 96-kHz/24-bit D/A converter

◆ “SET MENU” for optimizing this unit for your

Audio/Video system

◆ Test tone generator for easier speaker balance

adjustment

◆ 6-channel external decoder input

◆ On screen display function helpful in controlling

this unit

◆ S-video signal input/output capability

◆ Component video input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Remote control with preset manufacturer codes

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement

in operativity ability, and others. In this case, the product has priority.

0102V730_1-8_EN(U) 12/27/01, 2:16 PM2

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

–

3421

910

11 12

67 8

Installing batteries in the remote

control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

1 Press the part and slide off the battery

compartment cover.

2 Insert the four supplied batteries (AAA, R03,

UM-4) according to the polarity markings on

the inside of the battery compartment.

3 Slide the cover back on so that it snaps into

place.

■ Notes on batteries

• Change all of the batteries if you notice a decrease in

the operating range of the remote control, that the

indicator does not flash, or the light becoming dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

AM loop antenna

(Europe, U.K., Australia and

Singapore models)

Indoor FM antenna

(U.S.A., Canada, China,

Korea and General models)

Batteries (4)

(AAA, R03, UM-4)

Remote control

GETTING STARTED

Checking the package contents

Check your package to make sure it contains the following items.

75-ohm/300-ohm antenna

adapter (U.K. model)

Front VIDEO AUX jack cap

0102V730_1-8_EN(U) 12/27/01, 2:16 PM3

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

123 456

sa fd

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

iu po

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

START

EON

RDS MODE/FREQ

MODE

PTY SEEK

90 ert8qw y

CONTROLS AND FUNCTIONS

Front panel

1 STANDBY/ON

Turns this unit on, or set it to the standby mode. When

you turn this unit on, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit will consume a small amount of

power in order to receive infrared-signals from the

remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks. Priority cannot be

set when 6CH INPUT is selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the OUT (REC) level.

7 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks. This audio takes priority over the source selected

with INPUT l / h (or the input selector buttons on the

remote control).

(U.K. and Europe models)

0102V730_1-8_EN(U) 12/27/01, 2:16 PM4

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

8 SILENT (PHONES jack)

Allows you enjoy DSP effect for private listening with

headphones. When you connect headphones, no signals

are output to the speakers or the OUTPUT jacks.

9 SPEAKERS A/B

Turns the set of main speakers connected to the A and/or

B terminals on or off.

0 STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

q PROGRAM l / h

Selects the DSP program.

w PRESET/TUNING l / h

Selects preset station numbers 1 to 8 when the colon (:)

appears in the front panel display.

Selects the tuning frequency when the colon (:) does not

appear.

e A/B/C/D/E

Selects preset station groups A to E.

r BASS

Adjusts the low-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the low-

frequency response.

t TREBLE

Adjusts the high-frequency response for the main left and

right channels.

Turn right to increase or turn left to decrease the high-

frequency response.

y VIDEO AUX jacks

Inputs for audio and video signals from a portable

external source (game console, etc.). Set the input source

to V-AUX to enjoy source signals from these jacks.

When the VIDEO AUX jacks on the front panel are not

used, you can attach the provided front VIDEO AUX jack

cap as shown in the illustration. When the cap is not

attached, be sure retain it carefully.

u RDS MODE/FREQ (U.K. and Europe models)

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

service) and/or frequency display mode in turn.

i PTY SEEK MODE (U.K. and Europe models)

Press this button to set the unit in the PTY SEEK mode.

o PTY SEEK START (U.K. and Europe models)

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

p EON (U.K. and Europe models)

Press this button to select the desired program type

(NEWS, INFO, AFFAIRS, SPORT) when you want to

tune in to a radio program of that type automatically.

a PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

between selecting a preset station number and tuning (the

colon (:) turns on or off).

This button is also used to exchange the assignment of

two preset stations with each other.

s TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

d MEMORY (MAN’L/AUTO FM)

Stores the current station in the memory.

f FM/AM

Switches the reception band between FM and AM.

PTICA

S VID

VID

0102V730_1-8_EN(U) 12/27/01, 2:16 PM5

CONTROLS AND FUNCTIONS

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

0 +10

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

–

3421

910

11 12

67 8

Remote control

This section describes the remote control controls and

their functions. Make sure that the AMP mode is selected

before starting operation. See “REMOTE CONTROL

FEATURES” on pages 48 to 52.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

3 STANDBY

Sets this unit in the standby mode.

4 SYSTEM POWER

Turns on the power of this unit.

5 Å/ı/Ç

Sets the remote control to operate other components (not

necessarily connected to this unit) without changing this

unit’s input source.

6 Input selector buttons

Select the input source and set the remote control to

operate the selected source component.

7 Display window

Shows the selected source component that you are

controlling.

8 LEVEL

Selects the effect speaker channel to be adjusted.

9 Multi control section

Used when changing the setting and to implement the

settings.

0 TEST

Outputs the test tone to adjust the speaker levels.

q DSP program

Select DSP programs for the AMP position. Press a

button repeatedly to select a DSP program within that

group.

w RE-NAME

Used when changing the input source name in the display

window.

e CLEAR

Used when clearing functions acquired using the rename

features, and to set manufacturer codes.

r CODE SET

Used when setting up the manufacturer code (see page

49).

t SLEEP

Sets the sleep timer.

y 6CH INPUT

Selects the audio source connected to the 6CH INPUT

jacks.

0102V730_1-8_EN(U) 12/27/01, 2:16 PM6

English

INTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

CODE SET

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FMAUTO/MAN'L MONO

TUNING MODE

VOLUMEINPUT

INPUT M0DE

6CH INPUT

30° 30°

Approximately 6 m (20 feet)

u SELECT k/n

Sets the remote to control a component other than the one

selected using the input selector buttons.

i AMP

Switches the function of the same controls between AMP

and the component selected using the input selector

buttons.

o VOL +/–

Increases or decreases the volume level.

p MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

a SET MENU

Selects the SET MENU mode.

s ON SCREEN

Displays the input or operation status.

d STEREO/EFFECT

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the main left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

main left and right speakers.

Using the remote control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V730_1-8_EN(U) 12/27/01, 2:16 PM7

CONTROLS AND FUNCTIONS

LCR

RC RR

LFE

VIRTUAL

DSP

PCM

MATRIX

SILENT

DIGITAL

EON

PS PTY

PTY HOLD

MUTE

SLEEP

STEREO

TUNED

MEMORY

AUTO

PRO LOGIC

VOLUME

DTS

MOVIE

THTR

ENTERTAINMENT

DOLBY DIGITAL PRO

LOGIC

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

1234

5789

qwert y

1 Processor indicators

Lights up when the t, g, VIRTUAL,

PRO LOGIC

DSP

are activated.

MATRIX lights up when the Dolby Digital EX decoder or

the DTS-ES compatible decoder is activated.

2 Input source indicator

Shows the current input source with a cursor.

3 MUTE indicator

Flashes while the MUTE function is on.

4 VOLUME level indicator

Indicates the volume level.

5 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

6 SILENT indicator

Lights up when headphones are connected while the

digital sound field processor is on.

7 Headphones indicator

Lights up when headphones are connected.

8 DSP program indicators

The name of the selected DSP program lights up when the

ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

9 Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

0 RDS indicator (U.K. and Europe models)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

EON indicator lights up when an RDS station that offers

the EON data service is being received.

PTY HOLD indicator lights up while searching for

stations in the PTY SEEK mode.

q STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

w TUNED indicator

Lights up when this unit is tuned to a station.

e MEMORY indicator

Flashes to show a station can be stored.

r AUTO indicator

Shows that this unit is in the automatic tuning mode.

t SLEEP indicator

Lights up while the sleep timer is on.

y Input channel indicator

Indicates the channel components of input signals being

received.

Front panel display

(U.K. and Europe models)

0102V730_1-8_EN(U) 12/27/01, 2:16 PM8

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using main left and

right speakers, rear left and right speakers, a center

speaker, and a rear center speaker. If you use different

brands of speakers (with different tonal qualities) in your

system, the tone of a moving human voice and other types

of sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for effect and surround sounds. The center speaker is

for the center sounds (dialog, vocals, etc.). The rear center

speaker supplements the rear (left and right) speakers and

provides for more realistic front-to-back transitions.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

playing back Dolby Digital or DTS signals. The

YAMAHA Active Servo Processing Subwoofer System is

ideal for natural and lively bass reproduction.

PREPARATION

Speaker placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the main left and right speakers an equal distance

from the ideal listening position. The distance between

each speaker and each side of the video monitor should

also be the same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible (such as directly over or under the

monitor) and centrally between the main speakers.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the

rear left and right speakers at the same height from the

floor as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

Note

• If you do not use any of effect speakers (rear, center and/or rear

center), change the settings of SPEAKER SET items at the

SET MENU to designate the signals to other terminals you

connect speakers to.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V730_9-18_EN(U) 12/27/01, 2:16 PM9

SPEAKER SETUP

Connecting the speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit

and/or the speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

(U.S.A., Canada, Australia, China, Korea and General models)

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be

connected to either the MAIN A or the MAIN B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

Red: positive (+)

Black: negative (–)

Banana plug

(U.S.A. model)

0103V730_9-18_EN(U) 12/27/01, 2:16 PM10

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

PHONO

DVD

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIOGND

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

AC OUTLETS

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

Subwoofer

system

Rear center

speaker

Main B speaker

Center

speaker

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency

effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your

SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET

item “1E BASS” on the SET MENU to MAIN.

• Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote

control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 53).

Right Left

Main A speaker

Right Left

Left

The diagram shows the speaker layout in the listening

room.

0103V730_9-18_EN(U) 12/27/01, 2:17 PM11

SPEAKER SETUP

SPEAKERS

MAIN

MPONENT VIDEO

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

MAIN A OR B

A+B

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers,

the impedance of each speaker must

be 4 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

The impedance must be 6 Ω or

higher.

The impedance must be 6 Ω or

higher.

The impedance of each speaker must

be 6 Ω or higher.

If you use one set of main speakers,

the impedance of each speaker must

be 8 Ω or higher.

If you use two sets of main speakers,

the impedance of each speaker must

be 16 Ω or higher.

[Canada model only]

The impedance of each speaker must

be 8 Ω or higher.

The impedance must be 8 Ω or

higher.

The impedance must be 8 Ω or

higher.

The impedance of each speaker must

be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(U.S.A. model)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage

the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE

SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when

this unit is in the standby mode.

Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this

switch only when this unit is in the standby mode.

0103V730_9-18_EN(U) 12/27/01, 2:17 PM12

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Before connecting components

CAUTION

Do not connect this unit or other components to the

mains power until all connections between the

components have been completed.

• Be sure all connections are made correctly, that is to

say L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• When you connect other YAMAHA audio components

(such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same

number labels as !, #, $ etc. YAMAHA applies this

labeling system to all its products.

• After you have completed all connections, check them

again to make sure they are correct.

• The name of jack corresponds to input selector.

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. To enjoy multi-channel sound track

of DVD software, etc. with DSP effect, you need to make

digital connection. All digital input jacks are acceptable

for 96-kHz sampling digital signals.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

DIGITAL

OUTPUT

SPEAKERS

MAIN

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

DVD

OUT

PHONO

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

COMPONENT VIDEO

AUDIOAUDIOGND

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

CENTER

REAR

CENTER

REAR CENTER

OUTPUT

–

REAR

(SURROUND)

REAR

(SURROUND)

AC OUTLETS

(page 19)

6CH INPUT jacks

(page 18)

DIGITAL OUTPUT jack

(page 16)

OUTPUT jacks

(page 18)

DIGITAL INPUT jacks

(pages 13-16)

Antenna input terminals

(page 17)

Speaker terminals

(pages 10-11)

Video component jacks

(pages 14-15)

Audio component jacks

(page 16)

SUBWOOFER OUTPUT

jack (page 11)

0103V730_9-18_EN(U) 12/27/01, 2:17 PM13

CONNECTIONS

Connecting video components

Refer to the connection examples on the next page.

■ Types of video jacks

There are three types of video jacks as follows:

1 VIDEO jack

Conventional composite video signal.

2 S VIDEO jack

Transmits color and luminance separately and achives

high-quality color reproduction.

3 COMPONENT VIDEO jacks

Transmit color difference (P

, P

) and

luminance separately and provide the best quality

picture.

• Each type of video jack works independently. Signals

input through the composite video, S-video and

component jacks are only output through the

corresponding composite video, S-video, and

component jacks.

• Use a commercially available cable specified for

connecting each type of jacks.

• The description of the component video jacks may

differ depending on the component (e.g. Y, C

, C

/Y,

, P

/Y, B-Y, R-Y etc.). When using these jacks, refer

also to the operation instructions for the component

being connected.

■ Connecting a video monitor

Connect the video input jack on your video monitor to the

MONITOR OUT VIDEO jack.

Note

• If you connect this unit with a source component using S-video

(or Component video) jacks, you also need to connect your

video monitor using S-video (or Component video) jacks.

■ Connecting a DVD player/digital

TV/cable TV

Connect the optical digital audio signal output jack on

your component to the DIGITAL INPUT jack and

connect the video signal output jack on the component to

the VIDEO jack on this unit.

Then connect AUDIO jacks on your component to the

AUDIO jacks on this unit.

• If your video component has an S-video output or component

video output, connect the S-video signal output jack on the

component to the S VIDEO jack or connect the component

video signal output jacks on the component to the

COMPONENT VIDEO jacks.

• The AUDIO jacks are available for a video component which

does not have optical digital output jack. However, multi-

channel reproduction cannot be obtained with audio signals

input from AUDIO jacks.

■ Connecting a game console or

camcorder

Connect the optical digital audio signal output jack on

your video component to the OPTICAL jack on the front

panel and connect video signal output jack on the

component to the VIDEO jack on the front panel.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO

jack.

• The AUDIO jacks are available for a video component such as

a camcorder which does not have optical digital output jack.

■ Connecting a VCR or DVR (digital

video recorder)

Connect the audio signal input jacks on your video

component to the AUDIO OUT jacks and connect the

video signal input jack on the video component to the

VIDEO OUT jack on this unit for picture recording.

Connect the audio signal output jacks on your component

to the AUDIO IN jacks and connect the video signal

output jack on the component to the VIDEO IN jack on

this unit to play a source from your recording component.

Second VCR or digital video recorder can be connected

using VCR 2/DVR jacks.

• If your video component has an S-video input, connect the S-

video signal input jack on the component to the S VIDEO OUT

jack.

• If your video component has an S-video output, connect the S-

video signal output jack on the component to the S VIDEO IN

jack.

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• S-video and component video signals pass independently

through this unit’s video circuit. Make sure to connect this unit

to both a source component and a recording component using

the video jacks of the same system.

COMPONENT VIDEO

VIDEOS VIDEO

2 1 3

0103V730_9-18_EN(U) 12/27/01, 2:17 PM14

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

D-TV

/CBL

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

PHONO

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

MONITOR

OUT

VIDEO

TUNER

B/CBPR/CR

COMPONENT VIDEO

AUDIOAUDIOGND

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

MIN. /SPEAKER

MAIN

A OR B

A+B

CENTER

REAR CENTER

REAR

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

V V

AUDIO

OUTPUT

AUDIO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

VIDEO

INPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

OPTICAL

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

indicates video cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR 1

DVD player

TV/digital TV/

cable TV

Game console or

camcorder

0103V730_9-18_EN(U) 12/27/01, 2:17 PM15

CONNECTIONS

Connecting audio components

■ Connecting a CD player

Connect the coaxial digital output jack on your CD player

to the DIGITAL INPUT CD jack.

• The AUDIO jacks are available for a CD player which does not

have coaxial digital output jack.

■ Connecting a CD recorder or MD

recorder

Connect the optical digital signal input jack on your CD

recorder or MD recorder to the DIGITAL OUTPUT MD/

CD-R jack for digital recording.

Connect the optical digital output jack on your CD

recorder or MD recorder to the DIGITAL INPUT MD/

CD-R jack to play a source from your recording

component.

• The AUDIO jacks are available for an CD recorder or MD

recorder which does not have optical digital input or output

jack.

DIGITAL

OUTPUT

DIGITAL

INPUT

6CH INPUT

(PLAY)

OUT

(REC)

DVD

OUT

VCR 1

VCR 2

/VDR

/CD-R

D-TV

/CBL

OUT

PHONO

ANT

GND

UNBAL.

OPTICAL

D-TV/CBL

MD/CD-R

OPTICAL

COAXIAL

S VIDEO VIDEO

OUTPUT

S VIDEO

MONITOR OUT

VIDEO

TUNER

AUDIOGND

MAIN

CENTER

SUB

WOOFER

SUB

WOOFER

SURROUND

AUDIO

OPTICAL

INPUT

OPTICAL

OUTPUT

GND

OUTPUT

COAXIAL

OUTPUT

indicates right analog cables

indicates left analog cables

indicates signal direction

Turntable

CD player

CD recorder or

MD recorder

Notes

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

• DIGITAL OUTPUT jack and analog OUT (REC) jacks are

independent. Only digital signals are output from DIGITAL

OUTPUT jack and analog signals from OUT (REC) jacks.

■ Connecting a turntable

Connect the output jacks on your turntable to the PHONO

jacks.

PHONO jacks are for connecting a turntable with an MM

or high-output MC cartridge. If you have a turntable with

a low-output MC cartridge, use an in-line boosting

transformer or MC-head amplifier when connecting to

these jacks.

• Connect your turntable to the GND terminal to reduce noise in

the signal. Please note that this connection may increase noise

with some record players.

indicates optical cables

indicates coaxial cables

0103V730_9-18_EN(U) 12/27/01, 2:17 PM16

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

D-TV

/CBL

DVD

ANT

GND

UNBAL.

VIDEO

FREQUENCY

STEP

OUT

MONI

VIDEO

TUNER

100kHz/10kHz

FREQUENCY

STEP

50kHz/9kHz

FM/AM

Ground (GND terminal)

For maximum safety and minimum

interference, connect the antenna GND

terminal to a good earth ground. A good

earth ground is a metal stake driven into

moist earth.

Indoor FM

antenna

(included)

AM loop antenna

(included)

Connecting the antennas

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and

GND terminals.

3 Orient the AM loop antenna for the best

reception.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer

reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the

quality. Consult the nearest authorized YAMAHA

dealer or service center about the outdoor antennas.

FREQUENCY STEP switch (China and General

models)

Because the interstation frequency spacing

differs in different areas, set the

FREQUENCY STEP switch (located on

the rear panel) according to the frequency

spacing in your area.

North, Central and South America:

100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the

AC power plug of this unit from the AC

outlet.

Open the cover of the

included 75-ohm/300-ohm

antenna adapter.

Cut the external sleeve

of the 75-ohm coaxial

cable and prepare it for

connection.

Cut the lead wire and

remove it.

Insert the cable wire into the

slot, and clamp it with pliers.

Snap the cover into

place.

Unit:

mm (inch)

Lead wire

Clamp with

pliers.

Clamp

with

pliers.

Insert the wire

into the slot.

Both AM and FM indoor antennas are included with this

unit. In general, these antennas should provide sufficient

signal strength.

Connect each antenna correctly to the designated

terminals.

75-ohm/300-ohm antenna adapter (U.K. model)

11 (7/16)

8 (5/16)

6 (1/14)

0103V730_9-18_EN(U) 12/27/01, 2:17 PM17

CONNECTIONS

234

MAIN

CENTER

REAR

CENTER

OUTPUT

REAR

(SURROUND)

OUTPUT

SUB

WOOFER

Connecting an external amplifier

If you want to increase the power output to the speakers,

or want to use another amplifier, connect an external

amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for

output to an external amplifier, signals are output from the

SPEAKERS terminals as well.

1 SUBWOOFER jack

When using a subwoofer with built-in amplifier,

including the YAMAHA Active Servo Processing

Subwoofer System, connect the input jack of the

subwoofer system to this jack. Low bass signals

distributed from the main, center and/or rear channels are

directed to this jack in accordance with your SPEAKER

SET selections. The LFE (low-frequency effect) signals

generated when Dolby Digital or DTS is decoded are also

directed to this jack in accordance with your SPEAKER

SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, designate the signals to the main

left and right speakers by changing the settings of SPEAKER

SET item “1E BASS” on the SET MENU.

• Use the control on the subwoofer to adjust its volume level. It

is also possible to adjust the volume level by using this unit’s

remote control (see “ADJUSTING THE LEVEL OF THE

EFFECT SPEAKERS” on page 53).

2 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the

BASS and TREBLE settings.

3 REAR CENTER jack

Rear center channel line output jack.

4 CENTER jack

Center channel line output jack.

5 REAR (SURROUND) jacks

Rear channel line output jacks.

Connecting an external decoder

This unit is equipped with 6 additional input jacks (MAIN

left and right, CENTER, SURROUND left and right and

SUBWOOFER) for discrete multi-channel input from an

external decoder, sound processor, or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, settings of

“1 SPEAKER SET” on the SET MENU do not apply (except

for “1F MAIN Lv”).

0103V730_9-18_EN(U) 12/27/01, 2:17 PM18

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

Connecting the power supply

cords

VOLTAGE

SELECTOR

SWITCHED

120V 60Hz

100W MAX. TOTAL

AC OUTLETS

VOLTAGE SELECTOR

■ Connecting the AC power cord

Plug in this unit to the wall outlet.

■ AC OUTLETS (SWITCHED)

U.S.A., Canada, China, Europe, Singapore and

General models ..............................................2 OUTLETS

U.K. and Australia model ................................ 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLETS

is controlled by this unit’s STANDBY/ON (or SYSTEM

POWER and STANDBY). These outlets will supply

power to any source component connected to this unit

whenever this unit is turned on. The maximum power

(total power consumption of components) that can be

connected to the AC OUTLETS varies depending on the

area which it was purchasing.

China and General models ......................................... 50 W

Other models ........................................................... 100 W

■ VOLTAGE SELECTOR

(China and General models)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are 110/120/

220/240 V AC, 50/60 Hz.

Turning on the power

When all connections are complete, turn on the power of

this unit.

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power of

this unit.

The level of the main volume, and then the current

DSP program name appear on the front panel

display.

2 Turn on the video monitor connected to this

unit.

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

STANDBY

/ON

POWER

SYSTEM

Remote control

Front panel

(General model)

0104V730_19-23_EN(U) 12/27/01, 2:17 PM19

Selecting the OSD mode

P01 CONCERT HALL

ROOM SIZE…………1.O

LIVENESS…………………5

INIT.DLY…………45ms

P01 CONCERT HALL

ON-SCREEN DISPLAY (OSD)

You can display operational information for this unit on a

video monitor. If you display the SET MENU and DSP

program parameter settings on a monitor, it is much easier

to see the available options and parameters than it is by

reading this information on the front panel display.

• If a video source is playing, the OSD is superimposed over the

video image.

• The OSD signal is not output to the OUT (REC) jack, and will

not be recorded with any video signal.

• You can set the OSD to turn on (blue background) or off when

there is no video signal by using “10 DISPLAY SET” on the

SET MENU (see page 46).

OSD modes

You can select the amount of information the shown in

the on-screen display.

Full display

This mode shows the DSP program parameter settings

continuously on the video monitor.

Short display

This mode briefly shows the front panel display message

at the bottom of the screen and then disappears.

Display off

This mode briefly shows “DISPLAY OFF” at the bottom

of the screen and then disappears. In this mode, no

operational information will be shown on the monitor,

except when ON SCREEN is pressed.

Full display Short display

• When you choose the full display mode, INPUT l / h,

VOLUME and some other types of operational information are

displayed at the bottom of the screen in the same format as the

front panel display.

• The SET MENU and test tone display appear regardless of the

OSD mode.

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

TEST

ON SCREEN

EFFECT

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

TITLE

MUTE

POWER

AMP

AVTV

SELECT

–

1 Turn on the video monitor connected to this

unit.

2 Press AMP.

3 Press ON SCREEN on the remote control

repeatedly to change the display mode.

The OSD mode changes in the following order:

full display, short display, and display off.

Notes

• If your video monitor is connected only to the COMPONENT

VIDEO jacks of this unit, the OSD is not shown. Make sure to

connect your video monitor to the COMPONENT VIDEO

jacks and either VIDEO or S VIDEO jacks if you want to see

the OSD.

• Playing back video software that has an anti-copy signal or

video signals with a lot of noise may produce unstable images.

(When using two video monitors)

• If you select video source from a component connected to both

the S VIDEO IN and composite VIDEO IN jacks, and both S

VIDEO OUT and composite VIDEO OUT jacks are connected

to two different monitors, the OSD appears only the monitor

connected with S-video jacks. When there is no video signal

input from source component, the OSD appears on both

monitors.

0104V730_19-23_EN(U) 12/27/01, 2:17 PM20

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Item

1A CENTER

1B MAIN

1C REAR LR

1D REAR CT

1E BASS

1F MAIN Lv

Description

Sets center speaker availability and size.

Sets main speaker size.

Sets rear L/R speakers availability and size.

Sets rear center speaker availability and size.

Sets the speaker(s) to be used to output low bass signals.

Sets the main speaker level.

Possible settings (default

setting indicated in bold)

LRG/SML/NON

LARGE/SMALL

LRG/SML/NON

SWFR/MAIN/BOTH

Nrm (Normal)/–10 dB

SPEAKER MODE SETTINGS

This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your

configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings

as well as other possible settings.

If the initial settings shown in the following table are not appropriate for your speaker configuration,

see “1 SPEAKER SET” on pages 42-44 to change the settings.

Summary of SPEAKER SET items 1A through 1F

0104V730_19-23_EN(U) 12/27/01, 2:17 PM21

Using the test tone

Use the test tone to balance the output levels of the

speakers. The adjustment of each speaker output level

should be made at your listening position using the

remote control.

1 Press AMP to select the

AMP mode.

“AMP” appears in the display

window on the remote control.

2 Press TEST to output the

test tone.

3 Adjust the volume of this unit so you can

hear the test tone.

The test tone is heard (in order) from the main left

speaker, center speaker, main right speaker, rear right

speaker, rear center, rear left speaker, and the

subwoofer. The tone is produced for 2.5 seconds

from each speaker.

This section explains how to adjust speaker output levels

using the test tone generator. When this adjustment is

complete, the output level heard at the listening position

should be the same from each speaker. This is important

for best performance of the digital sound field processor,

and the various decoders (Dolby Digital, Dolby Pro

Logic, Dolby Pro Logic

and DTS).

Note

• Since this unit cannot enter the test mode while headphones are

connected to this unit, be sure to unplug the headphones from

the PHONES jack when using the test tone.

Before you begin

1 Turn on the video monitor connected to this

unit.

2 Press SPEAKERS A or B

to select the main

speakers to be used.

If you are using two sets of the

main speakers, press both A

and B.

3 Set the BASS and TREBLE controls on the

front panel to the center position.

TEST

RETURN

AMP

BASS

–

TREBLE

–

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

TEST

ON SCREEN

EFFECT

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

TITLE

MUTE

POWER

AMP

AVTV

SELECT

–

2,5

SPEAKERS

ADJUSTING SPEAKER OUTPUT LEVELS

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

VOL

–

VOLUME

Remote controlFront panel

0104V730_19-23_EN(U) 12/27/01, 2:17 PM22

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONSADJUSTING SPEAKER OUTPUT LEVELS

4 Adjust the level of the

effect speakers using j / i

so that it matches the

level of the main

speakers.

While adjusting, the test tone

is heard from the selected

speaker.

Note

• To adjust the level of the main speakers, use VOLUME knob

(or VOL +/– on the remote control).

5 When adjustment is

complete, press TEST to

stop the test tone.

Notes

• If “1A CENTER” on the SET MENU is set to NON, the center

channel sound is automatically output from the main left and

right speakers.

• If “1C REAR LR” on the SET MENU is set to NON, the

output level of the rear left, right and center speakers cannot be

adjusted in step 4. The test tone will be circulated skipping the

rear left and right speakers and the rear center speaker.

• If “1D REAR CT” on the SET MENU is set to NON, the

output level of the rear center speaker cannot be adjusted in

step 4. The test tone will be circulated skipping the rear center

speaker.

• If “1E BASS” on the SET MENU is set to MAIN, the test tone

will be circulated skipping the subwoofer.

• It is not necessary to readjust the speaker levels once they are

set (as long as you do not change the speakers). You can enjoy

listening to or watching the input source at the desired volume

simply by adjusting the VOLUME knob (or VOL +/– on the

remote control).

• If the output level of the effect speakers (center, rear left, rear

right, and rear center) cannot be increased enough to match the

level of the main speakers, set “1F MAIN Lv” on the SET

MENU to –10 dB (see page 44). This setting decreases the

main speaker output level to about one-third of the normal

level. After you have set “1F MAIN Lv” on the SET MENU to

–10 dB, adjust the levels for the center and rear speakers again.

* Subwoofer test tone is output after the rear left

speaker (LEFT SURROUND).

For your convenience, the state of the test tone

output is also shown on the monitor by an image of

an audio listening room.

The front panel display also shows which speaker is

outputting the test tone.

Note

• If the test tone cannot be heard, turn down the volume, set this

unit to standby mode and check the speaker connections.

LEFT

TEST DOLBY SUR.

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

LEFT SURROUND RIGHT SURROUND

CENTER

REAR CENTER

RIGHT

LEFT

*SUBWOOFER

TEST

RETURN

0104V730_19-23_EN(U) 12/27/01, 2:17 PM23

BASIC PLAYBACK

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power.

2 Turn on the video monitor connected to this

unit.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you are using two sets of

main speakers, press both A

and B.

4 Press INPUT l / h repeatedly (one of the

input selector buttons on the remote control)

to select the input source.

The selected input source name and input mode

appear on the front panel display for a few seconds.

To select the audio source connected to the 6CH

INPUT jacks

(When combining with a video source)

• You need to select the input to which the video source

component is connected before selecting audio source.

Press 6CH INPUT until “6CH INPUT” appears on the

front panel display.

Note

• If “6CH INPUT” is shown on the front panel display, no other

source can be played. To select another input source, first press

6CH INPUT to turn off “6CH INPUT” from the front panel

display.

INPUT

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

AVTV

–

3421

910

11 12

67 8

PHONO

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

464

STANDBY

/ON

POWER

SYSTEM

SPEAKERS

Remote control

Front panel

Selected input source

6CH INPUT

Remote controlFront panel

0105V730_24-29_EN(U) 12/27/01, 2:17 PM24

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

5 Start playback or select a broadcast station

on the source component.

Refer to the operation instructions for the

component.

6 Adjust the volume to the desired level.

The volume level is displayed digitally.

Example: –70 dB

Control range: VOLUME MUTE (minimum) to

0 dB (maximum)

The volume level indicator also shows the current

volume level as a bar graph.

If desired, use BASS and TREBLE. These controls

only effect the sound from the main speakers.

Notes

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the main left

and right speakers.

• If you have connected a recording component to the VCR 1

OUT, VCR 2/DVR OUT, or MD/CD-R OUT jacks, and you

notice distortion or low volume during playback of other

components, try turning the recording component on.

7 Select a DSP program if desired.

Use PROGRAM l / h (DSP program buttons on

the remote control) to select a DSP program. See

pages 30 to 34 for details about DSP programs.

When using the remote control, press AMP before

selecting a DSP program.

PHONO

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

VOL

–

VOLUME

BASS

–

TREBLE

–

Front panel

Remote control

■ BGV (background video) function

The BGV function allows you to enjoy video images

from a video source together with sounds from an audio

source. For example, you can enjoy listening to classical

music while having beautiful scenery from a video source

on the video monitor.

Select a source from the video group, then select a source

from the audio group using the input selector buttons on

the remote control. BGV selections cannot be made with

INPUT l / h on the front panel.

■ To mute the sound

1 Press MUTE on the

remote control.

To resume the audio output,

press MUTE again.

• You can also cancel mute by pressing VOL +/–, etc.

• During muting, the “MUTE” indicator flashes on the front

panel display.

■ When you have finished using

this unit

1 Press STANDBY/ON (STANDBY on the

remote control) to set this unit in the

standby mode.

PROGRAM

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

Front panel Remote control

STANDBY

/ON

STANDBY

Front panel

Remote control

MUTE

0105V730_24-29_EN(U) 12/27/01, 2:17 PM25

BASIC PLAYBACK

Input modes and indications

This unit comes with a variety input jacks. You can select

the type of input signals you desire.

Each time you turn on the power of this unit, the input

mode is set according to “9 INPUT MODE” setting on

the SET MENU (see page 46 for details).

1 Press INPUT MODE (the input selector

button that you have pressed to select the

input source on the remote control)

repeatedly until the desired input mode is

shown on the front panel display.

AUTO: In this mode, the input signal is selected

automatically as follows:

1) Digital signal

2) Analog signal

DTS: In this mode, only the digital input signal

encoded with DTS is selected, even if

another signal is input at the same time.

ANALOG: In this mode, only the analog input signal is

selected, even if a digital signal is input at

the same time.

Notes

• When AUTO is selected, this unit automatically determines the

type of signal. If this unit detects a Dolby Digital or DTS

signal, the decoder automatically switches to the appropriate

setting.

• When playing a disc encoded with Dolby Digital or DTS on

some LD or DVD players, the sound output delays for a

moment when playback resumes after a search because the

digital signal is selected again.

• When playing a LD source that has not been digitally recorded,

the sound may not be output for some LD players. In this case,

set the input mode to ANALOG.

INPUT MODE

DVD AUTO

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

PHONO

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

Remote controlFront panel

Input mode

■ Notes on 96-kHz sampling digital

signals

The digital input jacks of this unit can handle 96-kHz

sampling digital signals. Note the following when 96-kHz

sampling digital signal is input to this unit:

– DSP programs cannot be selected.

– Sound will be output as 2-channel stereo from only the

main left and right speakers. (There may be sound

output from the subwoofer depending on the

SPEAKER MODE settings on the SET MENU.)

Therefore, the level of the effect speakers cannot be

adjusted while listening to such a source.

■ Notes on playing DTS-CD/LDs

• If the digital output data of the player has been

processed in any way, you may not be able to perform

DTS decoding even if you make a digital connection

between this unit and the player.

• If you play a source encoded with a DTS signal and

set the input mode to ANALOG, this unit may

reproduce the noise of an unprocessed DTS signal. In

this case, connect the source to a digital input jack and

set the input mode to AUTO or DTS.

• If you switch the input mode to ANALOG while

playing a source encoded with a DTS signal, this unit

reproduces no sound.

• If you play a source encoded with a DTS signal with

the input mode set to AUTO;

– This unit automatically switches to the DTS-

decoding mode (The “t” indicator lights up) after

having detected the DTS signal. When playback of

the DTS source is completed, the “t” indicator

may flash. While this indicator is flashing, only DTS

source can be played. If you want to play a normal

PCM source soon, set the input mode back to AUTO.

– When the input mode is set to AUTO and a search or

skip operation is performed during playback of a

DTS source, the “t” indicator may flash. If this

status continues for longer than 30 seconds, this unit

will automatically switch from “DTS-decoding”

mode to PCM digital signal input mode. The “t”

indicator will turn off.

0105V730_24-29_EN(U) 12/27/01, 2:17 PM26

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

Selecting a sound field program

You can enhance your listening experience by selecting a

DSP program. For details about each program, see pages

30 to 34.

1 Press AMP.

2 Press one of the DSP program buttons on

the remote control to select the desired

program.

The name of the selected program appears on the

front panel display.

AMP

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

PROGRAM l / h

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

AVTV

–

3421

910

11 12

67 8

2,3

3 After selecting the desired program, press

the same button repeatedly to select the

desired sub-program if available.

Example: Pressing MOVIE THEATER 1 repeatedly

switches the sub-program between

“Sci-Fi” and “Spectacle”.

Notes

• There are 9 programs with sub-programs available with this

unit. However, the selection depends on the input signal format

and not all sub-programs can be used with all input signal

formats.

• The digital sound field processor cannot be used when a source

connected to the 6CH INPUT jacks of this unit is selected or

when 96-kHz sampling digital signals are input to this unit.

• The acoustics of your listening room affect the DSP program.

Minimize the sound reflections in your room to maximize the

effect created by the program.

• When you select an input source, this unit automatically selects

the last DSP program used with that source.

• When you set this unit in the standby mode, the current source

and DSP program are memorized and are automatically

selected when you turn on the power again.

• If a Dolby Digital or DTS signal is input when the input mode

is set to AUTO, the DSP program (No. 7–9) automatically

switches to the appropriate decoding program.

• When a monaural source is being played with PRO LOGIC/

Normal or PRO LOGIC/Enhanced, or PRO LOGIC Movie,

no sound will be heard from the main speakers and the rear

speakers. Sound can only be heard from the center speaker. (If

“1A CENTER” on the SET MENU is set to NON, the center

channel sound is output from the main speakers.)

• You can also select DSP program by pressing PROGRAM

l / h on the front panel.

• Select a program based on your listening preference. Program

names are just for reference.

DGTLz Sci-Fi

LCR

LFE

DSP

PRO LOGIC

VOLUME

MOVIE

THTR

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

Sub-program name

Program name

DGTL Spectacle

LCR

LFE

DSP

PRO LOGIC

VOLUME

MOVIE

THTR

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

Program name

Sub-program name

0105V730_24-29_EN(U) 12/27/01, 2:17 PM27

BASIC PLAYBACK

4 Press SELECT repeatedly to select the

decoder; PRO LOGIC or PRO LOGIC

5 After selecting on the decoder (PRO LOGIC

), select the mode appropriate for the

source by pressing q/DTS SUR.

The selection switches as follow;

PRO LOGIC

Movie ↔ PRO LOGIC Music

• You can select PRO LOGIC, PRO LOGIC Movie, and PRO

LOGIC Music by pressing PROGRAM l / h on the front

panel repeatedly.

■ Selecting PRO LOGIC

You can enjoy the 2-channel sources decoded into five or

six discrete channels by selecting PRO LOGIC

program No. 9.

1 Select a 2-channel source and start playback

on the source component.

2 Press AMP.

3 Press q/DTS SUR.

The previously selected sub program appears on the

front panel display.

PRO LOGIC

DSP

PRO LOGIC

VOLUME

PRO

LOGIC

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

Remote control

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

PROGRAM l / h

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

AVTV

–

3421

910

11 12

67 8

3,4,5

AMP

0105V730_24-29_EN(U) 12/27/01, 2:17 PM28

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

BASIC PLAYBACK

■ Playing Dolby Digital Surround

EX or DTS ES software

Press EX/ES to turn on the Dolby Digital EX or DTS-ES

compatible decoder.

The display changes AUTO → Matrix6.1 → OFF each

time the EX/ES button is pressed.

AUTO: This mode automatically switches Dolby

Digital EX and DTS-ES compatible

depending on the signal. Rear center speaker

does not work for 5.1 channel sources.

Matrix6.1: This setting produces 6-channel playback of

the input source using the Dolby Digital EX

or DTS-ES compatible decoder. The rear

center speaker can be used when playing a

5.1-channel source.

OFF: Rear center speaker does not work in this

setting. (Except for when the DSP program

“6ch” is selected.)

Notes

• No sound will be output from the rear center speaker if you

have set “1C REAR LR” or “1D REAR CT” on the SET

MENU to NON.

• The setting becomes AUTO once this unit turns into standby

mode.

• Some Dolby Digital Surround EX or DTS ES software may not

contain the signal that is necessary for this unit to switch to the

Dolby Digital EX or DTS-ES compatible decoding mode. To

turn on the decoder when playing such a source, select

“Matrix6.1”.

■ Virtual CINEMA DSP

With Virtual CINEMA DSP, you can enjoy all DSP

programs without rear speakers. It creates virtual speakers

to reproduce a natural sound field.

You can listen to virtual CINEMA DSP by setting “1C

REAR LR” in the SET MENU to NON. Sound field

processing changes to VIRTUAL CINEMA DSP

automatically.

Note

• This unit is not set in the virtual CINEMA DSP mode even if

“1C REAR LR” is set to NON in the following cases:

– when the 6ch Stereo, DOLBY DIGITAL Normal, Pro Logic

Normal, Pro Logic , or DTS Normal program is selected;

– when the sound effect is turned off;

– when 6CH INPUT is selected as the input source;

– when 96-kHz sampling digital signals are input to this unit;

– when using the test tone; or

– when connecting the headphones.

STEREO

EFFECT

STEREO

EFFECT

Front panel

Remote control

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

■ SILENT CINEMA DSP

You can enjoy a powerful sound field similar to what you

could expert from actual speakers with SILENT

CINEMA DSP. You can listen to SILENT CINEMA DSP

by connecting your headphones to the PHONES jack

while the digital sound field processor is on. Enjoy all the

DSP program using the headphones. The “SILENT”

indicator lights up on the front panel display. (When

sound effects are off, you listen to the source with normal

stereo reproduction.)

Notes

• This feature is not available when 6CH INPUT is selected or

96-kHz sampling digital signals are input to this unit.

• The sound of LFE channel will be mixed and output from the

headphone.

■ Normal stereo reproduction

1 Press STEREO to turn off the sound effect

for normal stereo reproduction.

Press STEREO again to turn the sound effect back

on.

Notes

• If you turn off the sound effects, no sound is output from the

center speaker, rear speakers, or rear center speaker.

• If you turn off the sound effects while a Dolby Digital or DTS

signal is being output, the dynamic range of the signal is

automatically compressed and the sounds of the center and rear

speaker channels are mixed and output from the main speakers.

• The volume may be greatly reduced when you turn off the

sound effects or if you set “4 D. RANGE” on the SET MENU

to MIN. In this case turn on the sound effect.

• The sound of LFE channel will be directed to the main left and

right or the subwoofer (or both) channels depending on the

setting of “1E BASS” on the SET MENU.

During stereo reproduction, you can display information such as

the type, format and sampling frequency of the signal input from

the components connected to this unit.

(While playing a source)

1 Press AMP.

2 Press d to display the information about the

input signal.

EX/ES

CHP/INDEX

The MATRIX indicator lights up.

Spectacle EX

DSP

MATRIX

DIGITAL

MOVIE

THTR

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

VCR2/DVR

0105V730_24-29_EN(U) 12/29/01, 9:37 PM29

DIGITAL SOUND FIELD PROCESSING (DSP)

Understanding sound fields

A sound field is defined as the “characteristic sound reflections of a

particular space.” In concert halls and other music venues, we hear

early reflections and reverberations as well as the direct sound

produced by the artist(s). The variations in the early reflections and

other reverberations among the different music venues is what gives

each venue its special and recognizable sound quality.

YAMAHA sent teams of sound engineers all around the world to

measure the sound reflections of famous concert halls and music

venues, and collect detailed sound field information such as the

direction, strength, range, and delay time of those reflections. Then

we stored this enormous amount of data in the ROM chips of this

unit.

■ Recreating a sound field

Recreating the sound field of a concert hall or an opera house requires localizing the virtual sound sources in your

listening room. The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound

field. YAMAHA’s DSP requires four effect speakers to recreate sound fields based on the measured sound field data.

The processor controls the strength and delay time of the signals output from the four effect speakers to localize the

virtual sound sources and fully encompass the listener.

Hi-Fi DSP programs

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments.

No.

Program

CONCERT HALL

JAZZ CLUB

ROCK CONCERT

ENTERTAINMENT/

Disco

ENTERTAINMENT/

6ch Stereo

Features

A large round concert hall with a rich surround effect. Pronounced reflections from all directions

emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual

seat is near the center, close to the stage.

This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club, that

seats up to 300 people. Its wide left to right seating arrangement offers a real and vibrant sound.

The ideal program for lively, dynamic rock music. The data for this program was recorded at

LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall.

This program recreates the acoustic environment of a lively disco in the heart of a big city. The

sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate”

sound.

Using this program increases the listening position range. This is a sound field suitable for

background music at parties, etc.

0106V730_30-34_EN(U) 12/27/01, 2:17 PM30

BASIC

OPERATION

English

INTRODUCTION PREPARATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

Sound design of CINEMA-DSP

Filmmakers intend for the dialog to be located right on the screen, the effect sound a little farther back, the music spread

even farther back, and the surround sound around the listener. Of course, all of these sounds must be synchronized with

the images on the screen.

CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP

integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field

programs to provide a surround sound field. It recreates comprehensive movie sound design in your audio room. In

CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the Main left and right, and

Center channels, so the listener can enjoy realistic dialogue, depth of sound, smooth transition between sound sources,

and a surround sound field that goes beyond the screen.

When a DTS or Dolby Digital signal is detected, the CINEMA-DSP sound field processor automatically chooses the

most suitable sound field program for that signal.

In addition to the DSP, this unit is equipped with a variety of precise decoders; Dolby Pro Logic decoder for Dolby

Surround sources, Dolby Pro Logic

decoder for Dolby Surround and 2-channel sources, Dolby Digital/DTS decoder

for multi-channel sources and Dolby Digital EX or DTS-ES compatible decoder for adding a rear center channel. You

can select CINEMA-DSP programs to optimize these decoders and the DSP sound patterns depending on the input

source.

L SURROUND SOUND FIELD

R SURROUND SOUND FIELD

PRESENCE SOUND FIELD

DIALOG

EFFECT MUSIC

0106V730_30-34_EN(U) 12/27/01, 2:17 PM31

CINEMA-DSP

The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without

using matrix processing. This unit’s MOVIE THEATER programs provide the same quality of sound and sound

localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality

sound designed for movie theaters into your home. With this unit’s MOVIE THEATER programs, you can use Dolby

Digital or DTS technology to recreate a dynamic sound that gives you the feeling of being in a public theater.

■ Dolby Digital/DTS + DSP sound field effect

These programs use YAMAHA’s tri-field DSP processing

on each of the Dolby Digital or DTS signals for the front,

left surround, and right surround channels. This

processing enables this unit to reproduce the immense

sound field and surround expression of a Dolby Digital-

or DTS-equipped movie theater without sacrificing the

clear separation of all channels.

■ Dolby Digital EX/DTS-ES compatible + DSP sound field effect

These programs provide you with the maximum experience of the spacious surround effects by adding an extra rear

center DSP sound field created from the rear center channel.

■ Dolby Pro Logic + DSP sound field effect

Most movie software has 4-channel (left, center, right,

and surround) sound information encoded by Dolby

Surround matrix processing and stored on the left and

right tracks. These signals are processed by the Dolby Pro

Logic decoder. The MOVIE THEATER programs are

designed to recreate the spaciousness and delicate

nuances of sound that tend to be lost in the encoding and

decoding processes.

■ Dolby Pro Logic

Dolby Pro Logic decodes Dolby Surround software into 5 discrete full-range channels (3 channels in front and 2

channels in rear). There are 2 modes; MOVIE for movies and MUSIC for 2-channel audio sources.

Surround DSP

sound field

Right surround DSP

sound field

Presence DSP

sound field

Left surround DSP

sound field

Presence DSP

sound field

0106V730_30-34_EN(U) 12/27/01, 2:17 PM32

English

INTRODUCTION PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CINEMA-DSP

CINEMA-DSP programs

■ For movie programs: No. 7 to 9

This unit automatically chooses the appropriate decoder and DSP sound field pattern according to the input signal

format.

Table of Program Names for Each Input Format

MOVIE

THEATER 1

MOVIE

THEATER 2

DOLBY

DIGITAL

DTS DIGITAL

SUR

PRO LOGIC

2 channel

Stereo

70 mm Spectacle

70 mm Sci-Fi

70 mm Adventure

70 mm General

—

Normal

Enhanced

Movie

Music

DOLBY DIGITAL

DGTL Spectacle

DGTL Sci-Fi

DGTL Adventure

DGTL General

Normal

Enhanced

—

5.1 channel

DTS

DTS Spectacle

DTS Sci-Fi

DTS Adventure

DTS General

—

Normal

Enhanced

—

DTS-ES

compatible

Spectacle ES

Sci-Fi ES

Adventure ES

General ES

—

DTS-ES

Enhanced ES

—

6.1 channel *

Input

Program

DOLBY DIGITAL

Spectacle EX

Sci-Fi EX

Adventure EX

General EX

Dolby D EX

Enhanced EX

—

* means the Dolby Digital EX decoder or the DTS-ES compatible decoder is ON.

• If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will automatically switch to

the Dolby Digital playback sound field or DTS playback sound field.

• If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the EX/ES button on the

remote control, the Dolby Digital EX or DTS-ES compatible decoder usually turns on and the corresponding DSP program is

selected.

• EX/ES on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with the rear center speaker. In this case

the program name changes to the corresponding name for 6.1 channel.

• When playing a 6.1 channel source with the Dolby Digital EX decoder or the DTS-ES compatible decoder turned off, the program

name changes to the corresponding name for 5.1 channel.

Notes

• The “ ” indicator does not light up when selecting program No. 9 except in Enhanced mode.

• When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, main and rear

speakers output effect sounds.

No.

0106V730_30-34_EN(U) 12/27/01, 2:18 PM33

CINEMA-DSP

Program

Enhanced Mode

No.

Program

ENTERTAINMENT/

Game

ENTERTAINMENT/

Concert Video

TV SPORTS

MONO MOVIE

Features

This program adds a deep and spatial feeling to video game sounds.

This program adds a deep and spatial feeling to concert video sounds.

With this program, you can enjoy watching various TV programs such as news, variety shows,

music programs or sports programs. In a stereo broadcast of a sports game, the commentator is

oriented at the center position, and the shouts and the atmosphere in the stadium spread on the

surround side, while their spread to the rear is properly restrained.

This program is provided for reproducing monaural video sources (such as old movies). The

program produces the optimum reverberation to create sound depth by using only the presence

sound field.

■ For audio-video sources: No. 4 to 6

The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in

mind that most of these are precise digital recreations of actual acoustic environments. Select the DSP program that you

feel sounds best regardless of the name and description given for it below.

No.

Features

This program creates the extremely wide sound field of a 70-mm movie theater. It

precisely reproduces the source sound in detail, making both the video and the sound

field incredibly real. This is ideal for any kind of video source encoded with Dolby

Surround, Dolby Digital or DTS (especially large-scale movie productions).

This program clearly reproduces dialog and sound effects in the latest sound form of

science fiction films, thus creating a broad and expansive cinematic space amid the

silence. You can enjoy science fiction films in a virtual-space sound field that includes

Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced

techniques.

This program is ideal for precisely reproducing the sound design of the newest 70-mm

and multichannel soundtrack films. The sound field is made to be similar to that of the

newest movie theaters, so the reverberations of the sound field itself are restrained as

much as possible.

This program is for reproducing sounds from 70-mm and multichannel soundtrack films,

and is characterized by a soft and extensive sound field. The presence sound field is

relatively narrow. It spatially spreads all around and toward the screen, restraining the

echo effect of conversations without losing clarity.

This program ideally simulates the multi-surround speaker systems of the 35-mm film

theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital

sound field processing create precise effects without altering the original sound

orientation.

The surround effects produced by this sound field wrap around the viewer naturally from

the back to the left and right, and toward the screen.

MOVIE

THEATER 1

MOVIE

THEATER 2

Spectacle

Sci-Fi

Adventure

General

0106V730_30-34_EN(U) 12/27/01, 2:18 PM34

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

4 Press PRESET/TUNING l / h once to begin

automatic tuning.

Press h to tune in to a higher frequency, or press l

to tune in to a lower frequency.

When tuned in to a station, the “TUNED” indicator

lights up and the frequency of the received station is

shown on the front panel display.

• Use the manual tuning method if the tuning search does not

stop at the desired station because the signal is weak.

■ Manual tuning

If the signal from the station you want to select is weak,

you must tune in to it manually.

1 Select TUNER and the reception band

following steps 1 and 2 described in

“Automatic tuning” at left.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator goes off from

the front panel display.

If the colon (:) appears on the front panel display,

press PRESET/TUNING (EDIT) to turn it off.

3 Press PRESET/TUNING l / h to tune in to

the desired station manually.

Hold down the button to

continue the tuning search.

Note

• Manually tuning in to an FM station will automatically change

the reception mode to monaural to increase the signal quality.

Automatic and manual tuning

There are 2 ways to tune; automatic and manual.

Automatic tuning is effective when station signals are

strong and there is no interference.

■ Automatic tuning

1 Press INPUT l / h (TUNER on the remote

control) to select TUNER as the input source.

2 Press FM/AM to select the reception band.

“FM” or “AM” appears on the front panel display.

3 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

If the colon (:) appears on the front panel display,

press PRESET/TUNING (EDIT) to turn it off.

INPUT

PRESET

TUNING

4233

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

FM/AM

AUTO/MAN'L MONO

TUNING MODE

AUTO

Lights up

EDIT

PRESET/TUNING

PHONO

POWER SLEEP

STANDBY

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

Front panel

Remote control

AUTO/MAN'L MONO

TUNING MODE

AUTO

Goes off

EDIT

PRESET/TUNING

PRESET

TUNING

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

DVR

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

DVR

A AM 144O

TUNED

VCR

V-AUX

DVD

TUNER

TV/CBL

MD/CD

DVR

0107V730_35-40_EN(U) 12/27/01, 2:18 PM35

TUNING

Presetting stations

■ Automatically presetting stations

(for FM stations)

You can use the automatic preset tuning feature to store

FM stations. This function enables this unit to

automatically tune in to FM stations with strong signals,

and to store up to 40 (8 stations x 5 groups) of those

stations in order. This feature enables you to easily tune in

to any preset station by selecting the preset station

number (see page 38).

1 Press FM/AM to select the FM band.

2 Press TUNING MODE (AUTO/MAN’L MONO)

so that the “AUTO” indicator lights up on the

front panel display.

3 Press and hold MEMORY (MAN’L/AUTO FM)

for more than 3 seconds.

The preset number and the “MEMORY” and

“AUTO” indicators flash. Then, after about

5 seconds, automatic preset tuning begins from the

frequency currently displayed toward the higher

frequencies.

When automatic preset tuning is completed, the front

panel display shows the frequency of the last preset

station.

AUTO/MAN'L MONO

TUNING MODE

MEMORY

MAN'L/AUTO FM

AUTO

A1:FM

MEMORY

AUTO

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

Lights up

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• When a station data is stored under a preset number, the

frequency and reception band are also stored.

• You can manually replace a preset station with another FM or

AM station by simply following the procedure in the section

“Manually presetting stations” on page 37.

• If the number of the received stations does not reach E8,

automatic preset tuning has automatically stopped after

searching all stations.

• Only FM stations with sufficient signal strength are stored

automatically by automatic preset tuning. If the station you

want to store is weak in signal strength, tune in to it manually

in the monaural mode, and store it by following the procedure

in “Manually presetting stations” on page 37.

Automatic preset tuning options

You can select the preset number from which this unit

will store FM stations and/or begin tuning toward lower

frequencies. After pressing MEMORY in step 3:

1. Press A/B/C/D/E and PRESET/TUNING l / h to

select the preset number under which the first station

will be stored. Automatic preset tuning will stop when

stations have all been stored up to E8.

2. Press PRESET/TUNING (EDIT) to turn off the colon

(:) and then press PRESET/TUNING l to begin

tuning toward lower frequencies.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the preset stations may be cleared. If

so, store the stations again.

FM/AM

0107V730_35-40_EN(U) 12/27/01, 2:18 PM36

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TUNING

■ Manually presetting stations

You can also store up to 40 stations (8 stations x 5

groups) manually.

1 Tune in to a station.

See page 35 for tuning instructions.

When tuned in to a station, the front panel display

shows the frequency of received station.

2 Press MEMORY (MAN’L/AUTO FM).

The “MEMORY” indicator flashes for about

5 seconds.

3 Press A/B/C/D/E repeatedly to select a preset

station group (A to E) while the “MEMORY”

indicator is flashing.

The group letter appears and make sure that the

colon (:) appears on the front panel display.

MEMORY

MAN'L/AUTO FM

MEMORY

A/B/C/D/E

C :AM 63O kHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

4 3 2,5

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

Shows the displayed station has been stored as C3.

Flashes

4 Press PRESET/TUNING l / h to select a

preset station number (1 to 8) while the

“MEMORY” indicator is flashing.

Press h to select a higher preset station number.

Press l to select a lower preset station number.

5 Press MEMORY (MAN’L/AUTO FM) on the

front panel while the “MEMORY” indicator is

flashing.

The station band and frequency

appear on the front panel

display with the preset group

and number you have selected.

6 Repeat steps 1 to 5 to store other stations.

Notes

• Any stored station data existing under a preset number is

cleared when you store a new station under that preset number.

• The reception mode (stereo or monaural) is stored along with

the station frequency.

A AM 63O kHz

TUNED

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

PRESET

TUNING

C3:AM 63O kHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

MEMORY

MAN'L/AUTO FM

C3:AM 63O kHz

TUNED

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

0107V730_35-40_EN(U) 12/27/01, 2:18 PM37

TUNING

Exchanging preset stations

You can exchange the assignment of two preset stations.

The example below describes the procedure for

exchanging preset station “E1” with “A5”.

1 Tune in to preset station “E1” by using the

A/B/C/D/E and PRESET/TUNING l / h.

See “Tuning in to a preset station” at left.

2 Press and hold PRESET/TUNING (EDIT) for

more than 3 seconds.

“E1” and the “MEMORY” indicator flash on the

front panel display.

3 Tune in to preset station “A5” by using the

A/B/C/D/E and PRESET/TUNING l / h.

“A5” and the “MEMORY” indicator flash on the

front panel display.

4 Press PRESET/TUNING (EDIT) again.

The stations stored at the two preset assignments are

exchanged.

Tuning in to a preset station

You can tune any desired station simply by selecting the

preset station number under which it was stored.

1 Press A/B/C/D/E (A/B/C/D/E on the remote

control) to select the preset station group.

The preset group letter appears on the front panel

display and changes each time you press A/B/C/D/E.

2 Press PRESET/TUNING l / h (PRESET j / i

on the remote control) to select a preset

station number (1 to 8).

The preset group and number appear on the front

panel display along with the station band, frequency

and the “TUNED” indicator lights up.

EDIT

PRESET/TUNING

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

PRESET

TUNING

A/B/C/D/E

SET MENU

A/B/C/D/E

A5:FM 9O.6 MHz

TUNED

MEMORY

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

EDIT E1-A5

MEMORY

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

VCR2/DVR

Shows the exchange of stations has

been completed.

Front panel

Remote control

Front panel

Remote control

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

SET MENU

TV INPUT

A/B/C/D/E

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

–

3421

910

11 12

67 8

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

2,41,3 1,3

EDIT

PRESET/TUNING

E1:FM 87.5 MHz

TUNED

MEMORY

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

VCR2/DVR

E1:FM 87.5 MHz

TUNED

VCR

V-AUX

DVD

TUNER CD

TV/CBL

MD/CD

VCR2/DVR

0107V730_35-40_EN(U) 12/27/01, 2:18 PM38

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Use this feature to automatically set this unit in the

standby mode after the amount of time you have set. The

sleep timer is useful when you are going to sleep while

this unit is playing or recording a source. The sleep timer

also automatically turns off the external component(s)

connected to AC OUTLET(S).

The sleep timer can only be set with the remote control.

• By connecting a commercially available timer to this unit, you

can also set a wake-up timer. Refer to the operation instructions

of the timer.

Setting the sleep timer

1 Select a source and start playback on the

source component.

2 Press SLEEP repeatedly

to set the amount of time.

Each time you press SLEEP,

the front panel display changes

as shown below.

SLEEP

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

SLEEP 12Omin

DSP

PCM

SLEEP

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

CONCERT HALL

DSP

PCM

SLEEP

VOLUME

VCR

V-AUX

DVD

TUNER

PHONO

TV/CBL

MD/CD

VCR2/DVR

SLEEP TIMER

Canceling the sleep timer

1 Press SLEEP repeatedly until “SLEEP OFF”

appears on the front panel display.

After a few seconds, “SLEEP OFF” disappears, the

“SLEEP” indicator goes off and the display returns

to the previous indication.

• The sleep timer setting can also be canceled by setting this unit

in the standby mode by using STANDBY on the remote control

(or STANDBY/ON on the front panel) or by disconnecting the

AC power cord from the AC outlet.

3 The “SLEEP” indicator lights up on the front

panel display soon after the sleep timer has

been set.

The display then returns to the previous indication.

0107V730_35-40_EN(U) 12/27/01, 2:18 PM39

INPUT

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

PHONO

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

Front panel Remote control

RECORDING

Notes

• Do a test recording before you start an actual recording.

• When this unit is set in the standby mode, you cannot record

between the components connected to this unit.

• The setting of BASS, TREBLE, VOLUME, “5 L/R

BALANCE” on the SET MENU and DSP programs does not

effect the recorded material.

• A source connected to the 6CH INPUT jacks on this unit

cannot be recorded.

• A given input source is not output to the same OUT (REC)

channel. (For example, the signal input from VCR 1 IN is not

output to VCR 1 OUT.)

• Check the copyright laws in your country to record from

records, CDs, radio, etc. Recording of copyrighted material

may infringe copyright laws.

If you playback a video source that uses scrambled or

encoded signals to prevent it from being dubbed, the

picture itself may be disturbed due to those signals.

■ Special considerations when

recording DTS software

The DTS signal is a digital bitstream. Attempting to

digitally record the DTS bitstream will result in noise

being recorded. Therefore, if you want to use this unit to

record sources that have DTS signals recorded on them,

the following considerations and adjustments need to be

made.

For LDs, DVDs and CDs encoded with DTS, when your

player is compatible with the DTS format, follow its

operation instruction to make a setting so that the analog

signal will be output from the player.

■ Timer playback/recording

This unit can perform playback or recording with an

external timer (not supplied). Refer to the operating

instructions for the component and the timer to be used.

Notes

• Stored data, such as input source, will be reflected when

playback or recording with the timer.

• If you do not want any sound output when recording with a

timer, turn the volume down.

Memory back-up

The memory back-up circuit prevents the stored data

(input source, volume level, set menu settings and so

on) from being lost even if this unit is disconnected

from the AC outlet. However, if the timer is turned off

for more than one week, the stored data will be lost.

NATURAL SOUND AV RECEIVER

SPEAKERS

SILENT

PHONES

STANDBY

STEREO

EFFECT

PROGRAM

PRESET

TUNING

A/B/C/D/E

BASS

– + – +

TREBLE

VIDEO AUX

S VIDEO VIDEO AUDIO OPTICALLR

MEMORY

FM/AM

EDIT

PRESET/TUNING

MAN'L/AUTO FM

AUTO/MAN'L MONO

TUNING MODE

VOLUME

INPUT

INPUT M0DE

6CH INPUT

Recording adjustments and other operations are

performed from the recording components. Refer to the

operation instructions for these components.

1 Turn on the power of this unit and all

connected component.

2 Select the source component you want to

record from.

3 Start playback (or select a broadcast station)

on the source component.

4 Start recording on the recording component.

0107V730_35-40_EN(U) 12/27/01, 2:18 PM40

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Adjusting the items on the SET

Adjustment should be made with the remote control.

Note

• Some items require extra steps.

1 Press AMP.

2 Press SET MENU to enter the SET MENU.

3 Press u/d repeatedly to select the item you

want to adjust (1 to 11).

• By pressing SET MENU repeatedly, you can select items in the

same order as when pressing d.

4 Press j / i once to enter the setup mode of

the selected item.

The last setting you adjusted appears on the video

monitor and/or on the front panel display.

AMP

SET MENU

ADVANCED OPERATION

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

–

3421

910

11 12

67 8

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

AUD O

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

4,5

3,6

The SET MENU consists of 11 items including the

speaker mode setting. Choose the appropriate item and

adjust or select the values as necessary.

• You can adjust the items on the SET MENU while playing a

source.

• We recommend that you adjust the items on the SET MENU

while using a video monitor.

Note

• The indication on the front panel display is an abbreviation of

the OSD.

Items Initial settings

1 SPEAKER SET

A CENTER LRG (large)

B MAIN LARGE

C REAR LR LRG (large)

D REAR CT LRG (large)

E BASS BOTH

F MAIN Lv Nrm (Normal)

2 LFE LEVEL SP/HP 0 dB

3 SP DLY TIME

CENTER 0 ms

REAR CNTR 3 ms

4 D. RANGE SP/HP MAX

5 L/R BALANCE 0 dB for L/R

HP TONE CTRL BASS/TRBL

0 dB

7 INPUT RENAME —

8 I/O ASSIGN

A (component video input) [A] DVD

[B] D-TV/CBL

B (optical output) (1) MD/CDR

C (optical input) (2) MD/CDR

(3) DVD

(4) D-TV/CBL

D (coaxial input) (5) CD

9 INPUT MODE AUTO

10 DISPLAY SET

BLUE BACK AUTO

OSD SHIFT 0

DIMMER 0

11 MEM. GUARD OFF

• In the descriptions for each item from the following page, the

default setting is indicated in bold.

SET MENU

A/B/C/D/E

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

2 LFE LEVEL

HEADPHONE…………0dB

≥ SPEAKER………………0dB

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

SET MENU 1/3

2 LFE LEVEL

3 SP DELAY TIME

4 DYNAMIC RANGE

/ : Up/Down

</>:Enter

≥ 1 SPEAKER SET

SET MENU 1/3

≥ 2 LFE LEVEL

3 SP DELAY TIME

4 DYNAMIC RANGE

/ : Up/Down

</> : Enter

1 SPEAKER SET

0108V730_41-47_EN(U) 12/27/01, 2:18 PM41

SET MENU

Depending on the item, press u/d to select a sub

item.

5 Press j / i repeatedly to change the setting

of the item.

6 Press u/d repeatedly until the menu

disappears or simply press one of the DSP

program group buttons to exit SET MENU.

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

2 LFE LEVEL

≥ HEADPHONE…………0dB

SPEAKER………………0dB

2 LFE LEVEL

≥ HEADPHONE……-11dB

SPEAKER………………0dB

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/INDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

1 SPEAKER SET (speaker mode

settings)

Use this feature to select suitable output modes for your

speaker configuration.

Notes

• When 96-kHz sampling digital signals are input to this unit,

some items are not affected.

• When 6CH INPUT is selected as the input source, level

adjustments in items 1A through 1E are not affected.

■ 1A CENTER (center speaker

mode)

By adding a center speaker to your speaker configuration,

this unit can provide better dialog localization for several

listeners and superior synchronization of sound and

images.

Choices: LRG (large), SML (small), NON (none)

LRG

Select this if you have a large center speaker. The entire

range of the center channel signal is directed to the center

speaker.

SML

Select this if you have a small center speaker. The low-

frequency signals (90 Hz and below) of the center

channel are directed to the speakers selected with “1E

BASS”.

NON

Select this if you do not have a center speaker. All of the

center channel signal are directed to the main left and

right speakers.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However, if the power cord is disconnected

from the AC outlet, or the power supply is cut for

more than one week, the stored data will be lost. If so,

adjust the items again.

0108V730_41-47_EN(U) 12/27/01, 2:18 PM42

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

■ 1B MAIN (main speaker mode)

Choices: LARGE, SMALL

LARGE

Select this if you have large main speakers. The entire

range of the main left and right channel signal is directed

to the main left and right speakers.

SMALL

Select this if you have small main speakers. The low-

frequency signals (90 Hz and below) of the main channel

are directed to the speakers selected with “1E BASS”.

■ 1C REAR LR (rear speaker mode)

Choices: LRG (large), SML (small), NON (none)

LRG

Select this if you have large rear left and right speakers or

if a rear subwoofer is connected to the rear speakers. The

entire range of the rear channel signal is directed to the

rear left and right speakers.

SML

Select this if you have small rear left and right speakers.

The low-frequency signals (90 Hz and below) of the rear

channel are directed to the speakers selected with “1E

BASS”.

NON

Select this if you do not have rear speakers.

• This unit is set in the virtual CINEMA DSP mode when you

select NON for “1C REAR LR”. In this case, the rear center

speaker will automatically be set to “NON” and the “1D REAR

CT” item will be skipped.

■ 1D REAR CT (rear center speaker

mode)

By adding a rear center speaker to your speaker

configuration, this unit can provide more realistic front-

to-back and transitions.

Choices: LRG (large), SML (small), NON (none)

LRG

Select this if you have a large rear center speaker. The

entire range of the rear center channel signal is directed to

the rear center speaker.

SML

Select this if you have a small rear center speaker. The

low-frequency signals (90 Hz and below) of the rear

center channel are directed to the speakers selected with

“1E BASS”.

NON

Select this if you do not have a rear center speaker. All of

the rear center channel signal are directed to the rear left

and right speakers.

■ 1E BASS (LFE/bass out mode)

LFE signals carry low-frequency effects when this unit

decodes a Dolby Digital or DTS signal. Low-frequency

signals are defined as 90 Hz and below. The Low-

frequency signals can be directed to both main left and

right speakers, and the subwoofer (subwoofer can be used

for both stereo reproduction and the DSP program).

Choices: SWFR (subwoofer), MAIN, BOTH

SWFR

Select this if you use a subwoofer. The LFE signals are

directed to the subwoofer.

MAIN

Select this if you do not use a subwoofer. The LFE

signals are directed to the main speakers.

BOTH

The LFE signals are directed to the subwoofer. Low-

frequency signals designated to the main channels in

accordance with other speaker mode settings are directed

to both main speakers and a subwoofer.

Note

• When you select MAIN for “1E BASS”, the low-frequency

signals (90 Hz and below) of the main channel are directed to

the main speakers even if you select SMALL for the main

speaker mode.

0108V730_41-47_EN(U) 12/27/01, 2:18 PM43

SET MENU

3 SP DLY TIME (speaker delay

time)

Use this feature to adjust the delay of the center and the

rear center channel sounds. This feature works when there

is sound output from the center speakers, with a source

like Dolby Digital or DTS, etc. Ideally, the center speaker

and the rear center speaker should be the same distance

from the main listening position as the left and right

speakers. However, in most home situations, the center

speaker or the rear center speaker are placed in line with

the main speakers or the rear speakers. By delaying the

sound from the center speaker and the rear center speaker,

the apparent distance from the center speaker and the rear

center speaker to the main listening position can be

adjusted to make it seem the same as the distance

between the main left and right speaker, and the rear left

and right speakers to the listening position. Adjusting the

delay time for the center speaker is especially important

for giving depth to the dialogue.

Control range:

CENTER .......................... 0 to 5 ms

REAR CNTR (center) ...... 0 to 30 ms

Initial setting:

CENTER .......................... 0 ms

REAR CNTR (center) ...... 3 ms

1 Press j / i to increase or decrease the delay

of the center and the rear center channel

sounds.

Center speaker image

• Increasing the delay by 1 ms simulates moving the speakers

about 30 cm (one foot) farther away from the listening

position.

3 SP DELAY TIME

REAR CNTR…………3ms

≥ CENTER…………………0ms

■ 1F MAIN Lv (main level mode)

Change this setting if you cannot match the output level

of the center, rear (L/R), and rear center speakers with the

main speakers because of unusually high-efficiency

performance from the main speakers.

Choices: Nrm (Normal), –10 dB

Nrm

Select this if you can match the output level of your effect

speakers with that of your main speakers when using the

test tone.

–10 dB

Select this if you cannot match the output level of your

effect speakers with that of your main speakers when

using the test tone.

2 LFE LEVEL

Use this feature to adjust the output level of the LFE

(low-frequency effect) channel when playing back a

Dolby Digital or DTS signal. The LFE signal carries the

low-frequency special effect sound which is only added to

certain scenes.

Control range:

SPEAKER ............ –20 to 0 dB

HEADPHONE ..... –20 to 0 dB

Initial setting: 0 dB

1 Press d/u to select the item to be adjusted.

2 Press j to adjust the LFE level.

Note

• Adjust the LFE level according to the capacity of your

subwoofer or headphones.

0108V730_41-47_EN(U) 12/27/01, 2:18 PM44

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

4 D. RANGE (dynamic range)

Use this feature to adjust the dynamic range. This setting

is effective only when this unit is decoding Dolby Digital

signals.

Choices: MAX, STD (standard), MIN (minimum)

MAX

Select the “MAX” for feature films.

STD

Select the “STD” for general use.

MIN

Select the “MIN” for listening to sources at low volume

levels.

5 L/R BALANCE (balance of the

main left and right speakers)

Use this feature to adjust the balance of the output level

from the main left and right speakers.

Control range: 20 steps for L/R

Initial setting: 0 dB for L/R

1 Press i to decrease the output level for the

main left speaker. Press j for the main right

speaker.

6 HP TONE CTRL (headphone tone

control)

Use this feature to adjust the level of the bass and treble

when you use your headphones.

Control range (dB):

BASS ............... –6 to +3

TRBL (treble) .. –6 to +3

Initial setting:

BASS ............... 0 dB

TRBL ............... 0 dB

7 INPUT RENAME

Use this feature to change the name of the input which

appears on the OSD or the front panel display.

1 Press an input selector button to select the

input you want to change the name of.

2 Press j / i to place the _ (under-bar) under

the space or the character you want to edit.

3 Press u/d to select the character you want

to use and j / i to move to the next one.

• Press d to change the character in the following

order, or press u to go in the reverse order.

A to Z, a space, 0 to 9, a space, a to z, a space, #,

*, +, and so on.

• Follow the foregoing procedure to rename other

inputs.

Note

• You can use up to 8 characters to rename the inputs.

4 Press i repeatedly to exit from INPUT

RENAME.

7 INPUT RENAME

</> : Position

/ : Character

DVD ≥ DVD

7 INPUT RENAME

</> : Position

/ : Character

DVD ≥ DVD1

7 INPUT RENAME

</> : Position

/ : Character

DVD ≥ DVD

0108V730_41-47_EN(U) 12/27/01, 2:18 PM45

SET MENU

10 DISPLAY SET

OSD SHIFT………………0

DIMMER………………………0

≥ BLUE BACK………AUTO

9 INPUT MODE (initial input

mode)

Use this feature to designate the input mode for sources

connected to the DIGITAL INPUT jacks when you turn

on this unit (see page 26 for details about the input

mode).

Choices: AUTO, LAST

AUTO

Select this to allow this unit to automatically detect the

type of input signal and select the appropriate input mode.

LAST

Select this to set this unit to automatically select the last

input mode used for the respective source.

10 DISPLAY SET

■ BLUE BACK

Select AUTO to display a blue background in the on-

screen display when there’s no video signal input.

Nothing is displayed on the screen, including the on-

screen display, if OFF is selected.

Choices: AUTO, OFF

■ OSD SHIFT (OSD off-set position)

This setting is used to adjust the vertical position of the

OSD.

Control range: +5 (downward) to –5 (upward)

Initial setting: 0

1 Press i to lower the position.

Press j to raise the position.

■ DIMMER

You can adjust the brightness of the front panel display.

Control range: –4 to 0

Initial setting: 0

8 I/O ASSIGN (input/output

assignment)

It is possible to assign jacks according to the component

to be used if this unit’s COMPONENT VIDEO input jack

or DIGITAL INPUT/OUTPUT jack settings (component

names for jacks) differ from that component. This makes

it possible to change the jack assignment and effectively

connect more components.

Once you assign, you can select that component with

INPUT l / h (or the input selector buttons on the

remote control).

■ 8A CMPNT-V INPUT for

COMPONENT VIDEO INPUT jacks

[A] and [B]

Choices: [A] DVD, V-AUX, VCR 2/DVR, VCR 1,

D-TV/CBL

[B] DVD, V-AUX, VCR 2/DVR, VCR 1,

D-TV/CBL

■ 8B OPTICAL OUT for OPTICAL

OUTPUT jack (1)

Choices: (1) MD/CD-R, CD, PHONO, V-AUX,

VCR 2/DVR, VCR 1, D-TV/CBL,

DVD

■ 8C OPTICAL IN for OPTICAL

INPUT jacks (2) to (4)

Choices: (2) MD/CD-R, CD, PHONO,

VCR 2/DVR, VCR 1, D-TV/CBL,

DVD

(3) MD/CD-R, CD, PHONO,

VCR 2/DVR, VCR 1, D-TV/CBL,

DVD

(4) MD/CD-R, CD, PHONO,

VCR 2/DVR, VCR 1, D-TV/CBL,

DVD

■ 8D COAXIAL IN for COAXIAL

INPUT jack (5)

Choices: (5) MD/CD-R, CD, PHONO, V-AUX,

VCR 2/DVR, VCR 1, D-TV/CBL,

DVD

Notes

• You cannot select an item more than once for the same type of

jack.

• When you connect a component to both the COAXIAL and

OPTICAL jacks, priority is given to the input signals from the

COAXIAL jack.

0108V730_41-47_EN(U) 12/27/01, 2:18 PM46

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SET MENU

11 MEM. GUARD (memory guard)

Use this feature to prevent accidental changes to settings

on this unit.

Choices: ON, OFF

Select ON to protect the following features:

• The on-screen display (OSD) mode

• All SET MENU items

• Center, rear speakers, rear center, and subwoofer

levels

• DSP program parameters

Notes

• When this item is set to ON, you cannot use the test tone.

• When this item is set to ON, you cannot select any other SET

MENU items.

0108V730_41-47_EN(U) 12/27/01, 2:18 PM47

REMOTE CONTROL FEATURES

In addition to controlling this unit, the remote control can operate other A/V components made by YAMAHA and other

manufacturers. To control other components, you must set up the remote control with the manufacturer codes.

Control area

■ Controlling this unit

The shaded areas below can be used to control this unit

when the AMP mode is selected. Press AMP to select the

AMP mode.

■ Controlling other component

The shaded areas below can be used to control other

components. Each button has a different function

depending on the selected components. Select the

component to be controlled by pressing an input selector

button or SELECT k/n. The name of the selected

component appears in the display window.

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

–

3421

910

11 12

67 8

Å/ı/Ç buttons and input

selector buttons switch the

control area for each component.

* Å/ı/Ç buttons are to operate

the other components that are

not connected to this unit.

Factory setting:

Å...LD player

ı...CD recorder

Ç...TV

Component control area

You can control up to 12 different components. You can set up

manufacturer code and program other remote control functions for

each component (see page 52).

Å/ı/Ç buttons

and input

selector buttons

SELECT k/n switches control

to another component without

changing the input source on

this unit.

The display window will show

one of the following:

A, B, C, PHONO, V-AUX,

TUNER, MDCDR, CD,

TVCBL, VCR 1, VCR 2, DVD.

The buttons in the

dotted lines

(SYSTEM

POWER,

STANDBY,

SLEEP, 6CH

INPUT, VOL +/–,

MUTE and

STEREO) function

in any mode.

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

AMP

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

LEVEL

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

POWER

AVTV

–

3421

910

11 12

67 8

Press AMP to

control this unit.

0109V730_48-53_EN(U) 12/27/01, 2:18 PM48

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

3 Press u / d to select the name of your

component’s manufacturer.

You will find the names of most worldwide audio-

video manufacturers in alphabetical order in the

display window.

If you want to change a library (component

category), press j / i. You can set a different

component from the input selector name.

Library choices: DVD, LD, CD, CD-R, MD, TAPE,

TUNER, TV, CABLE, DBS, SAT, VCR

Notes

• If the manufacturer of your component has more than one

code, try each of them until you find the correct one. Check to

see if the selected code works in step 4.

• If you wait for more than 30 seconds during step 3, the setup

process is canceled. If this happens, start over from step 2.

4 Press one of the buttons shaded below to

see if you can control your component. If so,

the manufacturer code is correct.

• If you want to continue setting up codes for other components,

press TV MUTE/SELECT and repeat steps 1, 3 and 4.

5 Press CODE SET again to exit from the setup

mode.

Note

•“ERROR” appears in the display window when pressing

buttons other than those indicated in each step, or when

pressing more than one button at once.

Setting the manufacturer code

You can control other components by setting a

manufacturer code. Codes can be set for each of the 12

component controls.

The following table shows factory-set component

(Library: component category) and the manufacturer code

for each component control.

1 Press an input selector button or Å/ı/Ç to

select the component you want to set up.

2 Press CODE SET using a ballpoint pen or

similar object.

“SETUP” and the selected component name appear

alternately in the display window.

PHONO

POWER SLEEP

STANDBY

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

CODE SET

Component

control

(buttons)

PHONO

V-AUX

TUNER

MD/CD-R

D-TV/CBL

VCR1

VCR2/DVR

DVD

Component category

(Library)

CD-R

VCR

TUNER

VCR

DVD

Manufacturer

YAMAHA

–

YAMAHA

–

YAMAHA

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

TV VOL

TITLE

MUTE

POWER

AMP

AVTV

–

CODE SET

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

0109V730_48-53_EN(U) 12/27/01, 2:18 PM49

REMOTE CONTROL FEATURES

Changing the source name in the

display window

You can change the name that appears in the display

window on the remote control if you want to use a

different name than the original. This is useful when you

have set the input selector buttons to control different

components.

1 Press an input selector button or Å/ı/Ç to

select the source component you want to

rename.

The selected component name appears in the display

window.

2 Press RE-NAME by using

a ballpoint pen or similar

object.

3 Press u / d to select and enter a character.

Pressing d changes the character in the following

order: A to Z, a to z, 0 to 9, space, - (hyphen) and /

(slash). (Pressing u goes in the reverse order.)

4 Press j / i to move the cursor to the next

position.

Repeat step 3 and 4 until the new name is completed.

• If you want to continue setting up codes for other components,

press TV MUTE/SELECT and repeat steps 1, 3 and 4.

5 Press RE-NAME again to exit from the

renaming mode.

PHONO

POWER SLEEP

STANDBY

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

RE-NAME

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

RE-NAME

0109V730_48-53_EN(U) 12/27/01, 2:18 PM50

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES

CLEAR

Clearing renamed source names,

and setup manufacturer codes

1 Press an input selector button or Å/ı/Ç to

select the component control for which you

want to clear the name, function or

manufacturer code.

2 Press CLEAR by using a ballpoint pen or

similar object.

Note

• If you do not press any button within 30 seconds after step 2,

the clearing process is canceled. If this happens, start over from

step 1.

3 Press u / d to select the clear mode.

The mode is shown in the display window in the

following order:

4 Press and hold CLEAR again for about 3

seconds.

“C:OK” appears in the display window.

Note

•“C:NG” appears in the display window if the operation is

unsuccessful. In this case, start over from step 2.

5 Press CLEAR to exit from the clearing mode.

Note

•“ERROR” appears in the display window when pressing

buttons other than indicated in each step, or more than one

button at once.

PHONO

POWER SLEEP

STANDBY

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL VCR2/DVRVCR 1 DVD

MD/CD-R

TUNER

Clears all renamed source names

in the display window.

Clears all setup manufacturer

codes and renamed source

names. This returns to the factory

settings.

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

(L: name of a component) Clears

setup manufacturer code for the

component control.

0109V730_48-53_EN(U) 12/27/01, 2:18 PM51

REMOTE CONTROL FEATURES

Controlling other components

DVD player VCR TV, digital/cable TV LD player CD player CD/MD recorder Tuner

1 TV POWER *

TV power *

TV power TV power *

TV power *

TV power

REC/DISC SKIP

Disc skip Rec *

VCR rec Disc skip Rec (MD)

3 w Play Play *

VCR play Play Play Play

y Skip forward Skip forward Skip forward Skip forward

t Skip backward Skip backward Skip backward Skip backward

d Pause Pause *

VCR pause Pause Pause Pause

a Stop Stop *

VCR stop Stop Stop Stop

4 e

Search backward Search backward

VCR search backward

Search backward Search backward Search backward

TITLE/TV INPUT

Title *

TV input TV input *

TV input *

TV input

6 TV VOL +/ u Up *

TV volume up TV volume up *

TV volume up *

TV volume up

TV VOL –/ d Down *

TV volume down TV volume down

TV volume down

CH +/ i Right VCR channel up TV channel up *

TV channel up *

TV channel up Preset up

CH –/ j Left

VCR channel down TV channel down

TV channel down

Preset down

TV MUTE/SELECT

Select *

TV mute TV mute *

TV mute *

TV mute

7 RETURN Return

8 1-11

Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Preset stations (1-8)

9 AV POWER *

Power *

VCR power *

Power *

Power

0 AUDIO Audio Sound

q r Search forward Search forward *

VCR search forward

Search forward Search forward Search forward

MENU/A/B/C/D/E

Menu A/B/C/D/E

e DISPLAY Display Display Display Display

r 12/CHP/INDEX Title/Index Enter Enter Chapter/Time Index Index

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

POWER

AMP

AVTV

SELECT

–

3421

910

11 12

67 8

This button functions only when the original remote control of the component has POWER button.

These buttons can operate your TV without switching the input if the manufacturer code is set in D-TV/CBL or Ç. When the

manufacturer code for your TV is set up in the both D-TV/CBL and Ç areas, priority is given to the signal in the D-TV/CBL area.

These buttons can operate your VCR without switching the input to VCR 1 if the manufacturer code is set in VCR 1.

You can operate other components when you have set the

manufacturer code for your component. Note, however,

that some buttons may not operate your component.

Once you select an input source, the remote control

switches to the mode for operating the component. You

can also select a component to operate other than the one

selected as the input source by pressing SELECT k/n.

The display window shows the currently selected

component that you can operate.

0109V730_48-53_EN(U) 12/27/01, 2:18 PM52

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

You can adjust the output level of each effect speaker

(center, rear left and right, rear center and subwoofer)

while listening to a source.

Adjustment should be made with the remote control.

1 Press AMP.

(While playing a source)

2 Press LEVEL repeatedly to select the

speaker(s) you want to adjust.

Each time you press LEVEL, the selected speaker

changes and appears on the front panel display as

follows: center, rear right, rear center, rear left and

subwoofer.

TV INPUT

LEVEL

TITLE

AMP

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

–

3421

910

11 12

67 8

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

AUD O

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV INPUT

LEVEL

TITLE

ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS

• Once you press LEVEL, you can also select the speaker(s) to

be adjusted by pressing d / u.

Center speaker output level

Subwoofer output level

Rear left speaker output

level

Rear center speaker output

level

Rear right speaker output

level

3 Press j / i to adjust the speaker output level.

• The control range for the center or rear left and

right speakers is from +10 dB to –10 dB.

• The control range for the subwoofer is from 0 dB

to –20 dB.

Notes

• When the speaker output modes for “1A CENTER” and “1C

REAR LR” are set to NON, and “1E BASS” to MAIN, the

output level of those speakers cannot be adjusted because there

is no sound coming from these speakers.

• When you adjust the output level with LEVEL, the settings you

made with the test tone will be changed.

• We recommend adjusting the speakers by following the steps

described in “Using the test tone” on pages 22 and 23.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is in the standby

mode. However, if the power cord is disconnected

from the AC outlet, or the power supply is cut for

more than one week, the stored data will be lost. If so,

set the output level again.

0109V730_48-53_EN(U) 12/27/01, 2:18 PM53

SOUND FIELD PROGRAM PARAMETER EDITING

What is a sound field?

What really creates the rich, full tones of a live instrument

are the multiple reflections from the walls of the room. In

addition to making the sound “live”, these reflections

enable us to tell where the player is situated, and the size

and shape of the room in which we are sitting.

■ Elements of a sound field

In any environment, in addition to the direct sound

coming straight to our ears from the player’s instrument,

there are two distinct types of sound reflections that

combine to make up the sound field:

Early reflections

Reflected sounds reach our ears extremely rapidly

(50 ms – 100 ms after the direct sound), after reflecting

from one surface only — for example, from the ceiling or

a wall. These reflections fall into specific patterns for any

particular environment, and provide vital information to

our ears. Early reflections actually add clarity to the direct

sound.

Reverberations

These are caused by reflections from more than one

surface — walls, ceiling, the back of the room — so

numerous that they merge together to form a continuous

sonic “afterglow”. They are non-directional, and lessen

the clarity of the direct sound.

Direct sound, early reflections and subsequent

reverberation taken together help us to determine the

subjective size and shape of the room, and it is this

information that the digital sound field processor

reproduces in order to create sound fields.

If you could create the appropriate early reflections and

subsequent reverberations in your listening room, you

would be able to create your own listening environment.

The acoustics in your room could be changed to those of

a concert hall, a dance floor, or virtually any size room at

all. This ability to create sound fields at will is exactly

what YAMAHA has done with the digital sound field

processor.

Sound field program parameters

DSP programs consist of some parameters to determine

the apparent room size, reverberation time, distance from

you to the performer, etc. In each program, these

parameters are set with values precisely calculated by

YAMAHA to create a sound field unique to the program.

It is recommended to use DSP programs without

changing the values of parameters. However, this unit

also allows you to create your own sound field by starting

with one of the built-in program and adjusting its

parameters.

Each DSP program has a set of parameters that allow you

to change the characteristics of the acoustic environment

to create the precise effect you want. These parameters

correspond to the many natural acoustic factors that create

the sound field you experience in an actual concert hall or

other listening environment. The size of the room, for

example, affects the length of time between the early

reflections. The “ROOM SIZE” parameter provided in

many of the DSP programs alters the timing between

these reflections, thus changing the shape of the “room”

you are listening. In addition to room size, the shape of

the room and the characteristics of its surfaces have a

significant effect on the final sound. Surfaces that absorb

sound, for example, cause the reflections and

reverberations to die out more quickly, while highly

reflective surfaces allow the reflections to carry on for a

longer period of time. The digital sound field parameters

allow you to control these and many other factors that

contribute to your personal sound field, allowing you to

essentially “redesign” the concert halls, theaters, etc.

provided to create custom-tailored listening environments

that ideally match your mood and music.

0110V730_54-59_EN(U) 12/27/01, 2:18 PM54

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

4 Press u / d to select the

parameter.

5 Press j / i to change the

parameter value.

• When you set the parameter to a value other than the factory-

set value, an asterisk mark (*) appears by the parameter name

on the video monitor. To reset to the factory-set value, press

j / i repeatedly until the asterisk mark disappears.

6 Repeat steps 3 to 5 above as necessary to

change other program parameters.

Notes

• For some of the programs, the available parameters may be

displayed on more than one OSD page. To scroll through

pages, press u / d.

• You cannot change parameter values when “11 MEM.

GUARD” on the SET MENU is set to ON.

Memory back-up

The memory back-up circuit prevents the stored data

from being lost even if this unit is set in the standby

mode, the power cord is disconnected from the AC

outlet, or the power supply is temporarily cut due to

power failure. However, if the power is cut for more

than one week, the parameter value you edited will

return to the factory setting. If so, edit the parameter

value again.

Changing parameter settings

You can enjoy high quality sound with the factory-set

parameters. Although you do not have to change the

initial settings, you can change some of the parameters to

better suit the input source or your listening room.

Adjustments should be made with the remote control.

• It is recommended to use on-screen display when changing the

settings.

1 Press AMP.

2 Turn on the video monitor

and press ON SCREEN

repeatedly to select the

full display mode.

3 Select a DSP program you want to adjust.

AMP

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

TV VOL

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

–

P03 ROCK CONCERT

ROOM SIZE…………1.0

LIVENESS…………………5

REV.TIME…………1.6s

REV.DELAY……120ms

REV.LEVEL……………7%

≥ INIT.DLY…………15ms

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

MATRIX 6.1

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

CHP/ NDEX

ROCK

CONCERT

JAZZ CLUB

3421

910

11 12

67 8

ON SCREEN

DISPLAY

Program No.

Example of the parameter setting display

Parameters

Cursor

Program name

PHONO

POWER SLEEP

CLEAR

CODE SET

STANDBY

TRANSMIT

RE–NAME

6CH INPUT

SYSTEM

AUX

A B C

TV/CBL

POWER

REC

POWER

AMP

AVTV

VCR2/DVRVCR 1 DVD

SELECT

MD/CD-R

TUNER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

STEREO

HALL

ENTER-

TAINMENT

SPORTS

MONO

MOVIE

SELECT

EX/ES

MOVIE

THEATER 1

MOVIE

THEATER 2

/DTS

SUR.

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

CHCH

ROCK

CONCERT

JAZZ CLUB

TITLE

MUTE

AVTV

–

3421

910

11 12

67 8

Parameter values

SOUND FIELD PROGRAM PARAMETER EDITING

0110V730_54-59_EN(U) 12/27/01, 2:18 PM55

2.00.1

Sound source

TimeTimeTime

Early

reflections

Sound source

Level

■ ROOM SIZE

[P. ROOM SIZE for the presence sound field]

Function: This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the

surround sound field becomes.

Description: As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between

the original reflected sound and the subsequent reflections. By controlling the time between the

reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from

one to two, doubles the apparent length of the room.

Control Range: 0.1 to 2.0

99 ms1 ms

Reflection face

Sound source

TimeTime Time

INIT.DLYINIT.DLYINIT.DLY

Early

reflections

Level

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your

listening room. Not all of the following parameters are found in every program.

■ INIT. DLY (Initial delay)

[P. INT. DLY for the presence sound field]

Function: This parameter changes the apparent distance from the source sound by adjusting the delay between the

direct sound and the first reflection heard by the listener.

Description: The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther

the apparent distance seems. For a small room, this parameter would be set to a small value, and for a

large room, it would be set to a large value.

Control Range: 1 to 99 msec

Sound source

0110V730_54-59_EN(U) 12/27/01, 2:18 PM56

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SOUND FIELD PROGRAM PARAMETER EDITINGDIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

■ S. DELAY (Surround delay)

Function: This parameter adjusts the delay between the direct sound and the surround sound. (Control range

varies depending on programs.)

Control range: varies depending on the signal format.

■ S. INIT. DLY (Surround initial delay)

Function: This parameter adjusts the delay between the direct sound and the first reflection on the surround side

of the sound field. You can only adjust this parameter when at least two front channels and two rear

channels are used.

Control range: 1 to 49 msec

■ S. ROOM SIZE (Surround room size)

Function: This parameter adjusts the apparent size of the surround sound field.

Control range: 0.1 to 2.0

■ S. LIVENESS (Surround liveness)

Function: This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field.

Control range: 0 to 10

■ RC. INIT. DLY (Rear center initial delay)

Function: This parameter adjusts the delay between the direct sound and the first reflection in the rear center

sound field.

Control range: 1 to 49 msec

■ RC. ROOM SIZE (Rear center room size)

Function: This parameter adjusts the apparent size of the rear center sound field.

Control range: 0.1 to 2.0

■ RC. LIVENESS (Rear center liveness)

Function: This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field.

Control range: 0 to 10

100

Large

reflected sound

Small reflected

sound

Sound source

Live

TimeTimeTime

Dead

Sound source

Level

■ LIVENESS

Function: This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the

early reflections decay.

Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall

surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces

is referred to as “dead”, while a room with highly reflective surfaces is referred to as “live”. The

LIVENESS parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the

room.

Control range: 0 to 10

0110V730_54-59_EN(U) 12/27/01, 2:18 PM57

DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

60 dB 60 dB 60 dB

(dB)

60 dB

Level

Time

REV. LEVEL

Sound source

■ REV. LEVEL (Reverberation level)

Function: This parameter adjusts the volume of the reverberation sound.

Description: The larger the value, the stronger the reverberation becomes.

Control range: 0 to 100%

Time

REV. TIMEREV.

DELAY

Reverberation

Sound source

Level

■ REV. DELAY (Reverberation delay)

Function: This parameter adjusts the time difference between the beginning of the direct sound and the beginning

of the reverberation sound.

Description: The larger the value, the later the reverberation sound begins. A later reverberation sound makes you

feel like you are in a larger acoustic environment.

Control range: 0 to 250 msec

5.0 s1.0 s

Sound source

REV. TIMEREV. TIMEREV. TIME

Early reflections

ReverberationSound sourceReverberation

■ REV. TIME (Reverberation time)

Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to

decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an

extremely wide range.

Description: Set a longer reverberation time for “dead” sources and listening room environments, and a shorter time

for “live” sources and listening room environments.

Control range: 1.0 to 5.0 sec

Short

reverberation

Long

reverberation

0110V730_54-59_EN(U) 12/27/01, 2:18 PM58

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SOUND FIELD PROGRAM PARAMETER EDITINGDIGITAL SOUND FIELD PARAMETER DESCRIPTIONS

For 6ch Stereo

Function: These parameters adjust the volume level for each channel in 6-channel stereo mode.

Control range: 0 to 100%

■ CT LEVEL (Center level)

■ RL LEVEL (Rear left level)

■ RR LEVEL (Rear right level)

■ RC LEVEL (Rear center level)

For PRO LOGIC Music

■ PANORAMA

Function: Extends the front stereo image to include the surround speakers for wraparound effect.

Choices: OFF/ON, initial setting is OFF.

■ DIMENSION

Function: Gradually adjusts the soundfield either towards the front or towards the rear.

Control range: –3 (towards the rear) to +3 (towards the front), initial setting is STD (standard).

■ CT WIDTH (Center width)

Function: Adjusts the center image from all three front speakers to varying degrees. The larger the value, adjusts

the center image towards the main left and right speakers.

Control range: 0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only

from main left and right speakers), initial setting is 3.

0110V730_54-59_EN(U) 12/27/01, 2:18 PM59

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and

contact the nearest authorized YAMAHA dealer or service center.

■ General

Problem

This unit fails to turn

on when STANDBY/

ON (or SYSTEM

POWER) is pressed,

or enters in the

standby mode soon

after the power has

been turned on.

On-screen display

does not appear.

No sound.

The picture does not

appear.

Cause

The power cord is not connected or the

plug is not completely inserted.

The IMPEDANCE SELECTOR switch

on the rear panel is not fully set to either

the left or right position.

The protection circuitry has been

activated.

This unit has been exposed to a strong

external electric shock (such as lightning

and strong static electricity).

The setting for the on-screen display is

set to “DISPLAY OFF”.

The BLUE BACK setting under “10

DISPLAY SET” on the SET MENU is

set to OFF, and no video signal is input

to this unit.

Incorrect input or output cable

connections.

An appropriate input source has not been

selected.

The speaker connections are not secure.

The main speakers to be used have not

been selected properly.

The volume is turned down.

The sound is muted.

Digital signals which this unit cannot

reproduce are being input to this unit by

playing a CD-ROM, etc.

The output and input for the picture are

connected to different types of video

jacks.

Remedy

Firmly connect the power cord.

Set the switch fully to the left or right position when

this unit is in the standby mode.

Make sure all speaker wire connections on this unit

and on all speakers are secure and that the wire for

each connection does not touch anything other than

its respective connection.

Set this unit in the standby mode, disconnect the

power cord, plug it back in after 30 seconds, then

start operating.

Select the full display or short display mode.

Set BLUE BACK to AUTO to always show the

OSD.

Connect the cables properly. If the problem persists,

the cables may be defective.

Select an appropriate input source with INPUT

l / h

or 6CH INPUT (or the input selector buttons).

Secure the connections.

Select the main speakers with SPEAKERS A and/or

Turn up the volume.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Play a source whose signals this unit can reproduce.

Make connections using the same type of video

jacks (S VIDEO, VIDEO (composite), or

COMPONENT VIDEO) for both the input and

output.

Refer

to page

—

10, 11

—

10 – 16

10, 11

—

14, 15

0111V730_60-67_EN(U) 12/27/01, 2:18 PM60

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

Problem

The sound suddenly

goes off.

Only the speaker on

one side can be

heard.

No sound from the

effect speakers.

No sound from the

center speaker.

No sound from the

rear speakers.

No sound from the

subwoofer.

Poor bass

reproduction.

Cause

The protection circuit has been activated

because of a short circuit, etc.

The sleep timer has functioned.

The sound is muted.

Incorrect cable connections.

Incorrect setting of “5 L/R BALANCE”

on the SET MENU.

The sound effect is off.

A Dolby Surround, Dolby Digital or

DTS decoding DSP program is being

used with material not encoded with

Dolby Surround, Dolby Digital or DTS.

A 96-kHz sampling digital signal is

being input to this unit.

The output level of the center speaker is

set to minimum.

“1A CENTER” on the SET MENU is set

to NON.

One of the Hi-Fi DSP programs (1 to 4)

has been selected (except for 6ch Stereo).

The source encoded with a Dolby Digital

or DTS signal does not have a center

channel signal.

The output level of the rear speakers is

set to minimum.

A monaural source is being played with

program 9.

“1E BASS” on the SET MENU is set to

MAIN when a Dolby Digital or DTS

signal is being played.

“1E BASS” on the SET MENU is set to

SWFR or MAIN when a 2-channel

source is being played.

The source does not contain low bass

signals (90 Hz and below).

“1E BASS” on the SET MENU is set to

SWFR or BOTH and your system does

not include a subwoofer.

The speaker mode settings (main, center,

rear, or rear center) on the SET MENU

does not match your speaker

configuration.

Remedy

Check the IMPEDANCE SELECTOR switch is set

to the appropriate position and then turn this unit

back on.

Check the speaker wires are not touching each other

and then turn this unit back on.

Turn on the power, and play the source again.

Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

Connect the cables properly. If the problem persists,

the cables may be defective.

Adjust it to the appropriate position.

Press STEREO/EFFECT to turn it on.

Select another DSP program.

Raise the level of the center speaker.

Select the appropriate mode for your center speaker.

Select another DSP program.

Raise the output level of the rear speakers.

Select another DSP program.

Select SWFR or BOTH.

Select BOTH.

Select MAIN.

Select the appropriate position for each speaker

based on the size of the speakers in your

configuration.

Refer

to page

—

10, 11

27 – 34

—

27 – 34

—

27 – 34

—

42 – 44

0111V730_60-67_EN(U) 12/27/01, 2:18 PM61

TROUBLESHOOTING

Problem

No sound from the rear

center speaker.

A “humming” sound

can be heard.

The volume level is low

while playing a record.

The volume level

cannot be increased, or

the sound is distorted.

The sound effect

cannot be recorded.

A source cannot be

recorded by a digital

recording component

connected to the

DIGITAL OUTPUT jack

of this unit.

The sound field

parameters and some

other settings on this

unit cannot be

changed.

This unit does not

operate properly.

“CHECK SP WIRES”

appears on the front

panel display.

There is noise

interference from digital

or high-frequency

equipment, or this unit.

This unit suddenly

turns into the standby

mode.

Cause

“1C REAR LR” or “1D REAR CT” on

the SET MENU is set to NON.

The Dolby Digital EX decoder or the

DTS-ES compatible decoder is not on.

Incorrect cable connections.

No connection from the turntable to the

GND terminal.

The record is being played on a turntable

with an MC cartridge.

The component connected to the OUT

(REC) jacks of this unit is turned off.

It is not possible to record the sound

effect by a recording component.

A source component is not connected to

the DIGITAL INPUT jacks of this unit.

“11 MEM. GUARD” in the SET MENU

is set to ON.

The internal microcomputer has been

frozen by an external electric shock (such

as lightning or excessive static electricity)

or by a power supply with low voltage.

Speaker cables are short circuited.

This unit is too close to the digital or

high-frequency equipment.

The internal temperature becomes too

high and the overheat protection circuitry

has been activated.

Remedy

Select LRG or SML.

Press the EX/ES button on the remote control to

turn it on.

Firmly connect the audio plugs. If the problem

persists, the cables may be defective.

Connect the grounding cord of your turntable to

the GND terminal of this unit.

The turntable should be connected to this unit

through an MC-head amplifier.

Turn on the power to the component.

Connect the source component to the DIGITAL

INPUT jacks of this unit.

Set “11 MEM. GUARD” in the SET MENU to

OFF.

Disconnect the AC power cord from the outlet

and then plug it in again after about 30 seconds.

Make sure all speaker cables are connected

correctly.

Move this unit further away from such

equipment.

Wait until this unit cools down and then turn it

back on.

Refer

to page

10 – 16

—

0111V730_60-67_EN(U) 12/27/01, 2:18 PM62

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

TROUBLESHOOTING

■ Tuner

FM stereo reception is

noisy.

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

The desired station

cannot be tuned in with

the automatic tuning

method.

Previously preset

stations can no longer

be tuned in.

The desired station

cannot be tuned in with

the automatic tuning

method.

There are continuous

crackling and hissing

noises.

There are buzzing and

whining noises

(especially in the

evening).

Problem

Cause

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

There is multipath interference.

The station is too weak.

This unit has been disconnected for a

long period.

The signal is weak or the antenna

connections are loose.

Noises result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

A TV set is being used nearby.

Remedy

Check the antenna connections.

Try using a high-quality directional FM

antenna.

Use the manual tuning method.

Adjust the antenna position to eliminate

multipath interference.

Use a high-quality directional FM antenna.

Use the manual tuning method.

Re-store the stations.

Tighten the AM loop antenna connections

and orient it for best reception.

Use the manual tuning method.

Use an outdoor antenna and a ground wire.

This will help somewhat, but it is difficult to

eliminate all noise.

Move this unit away from the TV.

Refer

to page

—

36, 37

—

■ Remote control

Problem

The remote control

does not work nor

function properly.

Cause

Wrong distance or angle.

Direct sunlight or lighting (from an

inverter type of fluorescent lamp, etc.) is

striking the remote control sensor of this

unit.

The batteries are weak.

The manufacture code has not correctly

set.

Even if the manufacturer code is

correctly set, there are some models that

do not respond to the remote control.

Remedy

The remote control will function within a

maximum range of 6 m (20 feet) and no more

than 30 degrees off-axis from the front panel.

Reposition this unit.

Replace all batteries with new ones.

Set the code correctly.

Try setting another code of the same

manufacturer.

Refer to

page

—

0111V730_60-67_EN(U) 12/27/01, 2:19 PM63

GLOSSARY

■ Dolby Surround

Dolby Surround uses a 4 channel analog recording system

to reproduce realistic and dynamic sound effects: 2 main

left and right channels (stereo), a center channel for

dialog (monaural), and a rear channel for special sound

effects (monaural). The rear channel reproduces sound

within a narrow frequency range.

Dolby Surround is widely used with nearly all video tapes

and laser discs, and in many TV and cable broadcasts as

well. The Dolby Pro Logic decoder built into this unit

employs a digital signal processing system that

automatically stabilizes the volume on each channel to

enhance moving sound effects and directionality.

■ Dolby Digital

Dolby Digital is a digital surround sound system that

gives you completely independent multi-channel audio.

With 3 front channels (left, center, and right), and 2 rear

stereo channels, Dolby Digital provides 5 full-range audio

channels. With an additional channel especially for bass

effects, called LFE (low frequency effect), the system has

a total of 5.1 channels (LFE is counted as 0.1 channel).

By using 2-channel stereo for the rear speakers, more

accurate moving sound effects and surround sound

environment are possible than with Dolby Surround. The

wide dynamic range (from maximum to minimum

volume) reproduced by the 5 full-range channels and the

precise sound orientation generated using digital sound

processing provide listeners with previously unheard of

excitement and realism.

With this unit, any sound environment from monaural up

to a 5.1-channel configuration can be freely selected for

your enjoyment.

Dolby Digital EX creates 6 full-bandwidth output

channels from 5.1-channel sources. This is done using a

matrix decoder that derives 3 surround channels from the

2 in the original recording. For the best results, Dolby

Digital EX should be used with movie sound tracks

recorded with Dolby Digital Surround EX. With this

additional channel, you can experience more dynamic and

realistic moving sound especially with scenes with “fly-

over” and “fly-around” effects.

■ Dolby Pro Logic

Dolby Pro Logic is an improved technique used to

decode vast numbers of existing Dolby Surround

softwares. This new technology enables a discrete 5-

channel playback with 2 main left and right channels, 1

center channel, and 2 rear left and right channels (instead

of only 1 rear channel for conventional Pro Logic

technology). A music mode is also available for 2-channel

sources in addition to the movie mode.

■ DTS (Digital Theater Systems)

Digital Surround

DTS digital surround was developed to replace the analog

soundtracks of movies with a 6-channel digital sound

track, and is now rapidly gaining popularity in movie

theaters around the world. Digital Theater Systems Inc.

has developed a home theater system so that you can

enjoy the depth of sound and natural spatial

representation of DTS digital surround in your home.

This system produces practically distortion-free 6-channel

sound (technically, a left, right and center channels, 2 rear

channels, plus an LFE 0.1 channel as a subwoofer, for a

total of 5.1 channels).

The unit incorporates DTS-ES compatible decoder that

enables 6.1-channel reproduction by adding the rear

center channel to existing 5.1-channel format. (The rear

center channel is created from rear left and right

channels.)

■ LFE 0.1 channel

This channel is for the reproduction of low bass signals.

The frequency range for this channel is 20 Hz to 120 Hz.

This channel is counted as 0.1 because it only enforces a

low frequency range compared to the full-range

reproduced by the other 5 channels in a Dolby Digital or

DTS 5.1 channel systems.

■ CINEMA DSP

DIGITAL

Since the Dolby Surround and DTS systems were

originally designed for use in movie theaters, their effect

is best felt in a theater having many speakers and

designed for acoustic effects. Since home conditions,

such as room size, wall material, number of speakers, and

so on, can differ so widely, it’s inevitable that there are

differences in the sound heard as well. Based on a wealth

of actually measured data, YAMAHA CINEMA DSP uses

YAMAHA original sound field technology to combine

Dolby Pro Logic, Dolby Digital and DTS systems to

provide the visual and audio experience of movie theater

in the listening room of your own home.

■ SILENT CINEMA

YAMAHA has developed a natural, realistic sound effect

DSP algorithm for headphones.

Parameters for headphones have been set for each sound

field so that accurate representations of all the sound field

programs can be enjoyed using headphones.

0111V730_60-67_EN(U) 12/27/01, 2:19 PM64

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

GLOSSARY

■ Virtual CINEMA DSP

YAMAHA has developed a virtual CINEMA DSP

algorithm that allows you to enjoy DSP sound field

surround effects even without any rear speakers by using

virtual rear speakers.

It is even possible to enjoy virtual CINEMA DSP using a

minimal 2-speaker system that does not include a center

speaker.

■ PCM (Linear PCM)

Linear PCM is a signal format under which an analog

audio signal is digitized, recorded and transmitted without

using any compression. This is used as a method of

recording CDs and DVD audio. The PCM system uses a

technique for sampling the size of the analog signal per

very small unit of time. Standing for “pulse code

modulation”, the analog signal is encoded as pulses and

then modulated for recording.

■ Sampling frequency and number

of quantized bits

When digitizing an analog audio signal, the number of

times the signal is sampled per second is called the

sampling frequency, while the degree of fineness when

converting the sound level into a numeric value is called

the number of quantized bits.

The range of rates that can be played back is determined

based on the sampling rate, while the dynamic range

representing the sound level difference is determined by

the number of quantized bits. In principle, the higher the

sampling frequency, the wider the range of frequencies

that can be played back, and the higher the number of

quantized bits, the more finely the sound level can be

reproduced.

■ S-video signal

With the S-video signal system, the video signal normally

transmitted using a pin cable is separated and transmitted

as the Y signal for the luminance and the C signal for the

chrominance through the S-video cable. Using the S

VIDEO jack eliminates video signal transmission loss and

allows recording and playback of even more beautiful

images.

■ Component video signal

With the component video signal system, the video signal

is separated into the Y signal for the luminance and the

and P

signals for the chrominance. Color can

be reproduced more faithfully with this system because

each of these signals is independent. The component

signal is also called the “color difference signal” because

the luminance signal is subtracted from the color signal.

A monitor with component input jacks is required in order

to use the component signal for output.

0111V730_60-67_EN(U) 12/27/01, 2:19 PM65

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power for Main, Center, Rear, Rear Center

20 Hz to 20 kHz, 0.06% THD, 8 Ω ....................................... 75 W

1 kHz, 0.06% THD, 8 Ω ........................................................ 80 W

• DIN Standard Output Power

[Europe model]

1 kHz, 0.7% THD, 4 Ω ........................................................ 125 W

• Maximum Power (EIAJ)

[China, Korea and General models]

1 kHz, 10% THD, 8 Ω ......................................................... 110 W

• Dynamic Power (IHF)

8/6/4/2 Ω .......................................................... 90/120/150/190 W

• Damping Factor

20 Hz to 20 kHz, 8 Ω ................................................... 80 or more

• Frequency Response

CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB

• Total Harmonic Distortion

20 Hz to 20 kHz, 50 W, 8 Ω, Main L/R ................................ 0.06%

• Signal to Noise Ratio (IHF-A Network)

PHONO MM to OUT (REC) (5 mV, shorted)

[U.S.A., Canada, China, Korea and General models] ....... 86 dB

[Other models] ................................................................... 81 dB

CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB

• Residual Noise (IHF-A Network)

Main L/R ................................................................ 150 µV or less

• Channel Separation (1 kHz/10 kHz)

CD (5.1 kΩ terminated) to Main L/R ........................ 60 dB/45 dB

• Tone Control (Main L/R)

BASS Boost/Cut ...................................................... ±10 dB/50 Hz

TREBLE Boost/Cut ............................................... ±10 dB/20 kHz

• Phones Output ............................................................. 0.34 V/560 Ω

• Input Sensitivity

CD, etc .................................................................... 150 mV/47 kΩ

6CH INPUT ............................................................ 150 mV/47 kΩ

• Output Level

OUT (REC) ........................................................... 150 mV/1.2 kΩ

OUTPUT MAIN/CENTER/REAR CENTER/

REAR (SURROUND) ............................................ 2.2 V/1.2 kΩ

OUTPUT SUBWOOFER ............................................. 4 V/1.2 kΩ

VIDEO SECTION

• Video Signal Type ...................................................... NTSC or PAL

• Composite Video Signal Level ...................................... 1 Vp-p/75 Ω

• S-Video Signal Level

Y ................................................................................. 1 Vp-p/75 Ω

C .......................................................................... 0.286 Vp-p/75 Ω

• Component Video Signal Level

Y ................................................................................. 1 Vp-p/75 Ω

, P

............................................................. 0.7 Vp-p/75 Ω

• Signal to Noise Ratio ............................................................... 50 dB

• Frequency Response (MONITOR OUT)

Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB

Component ................................................. DC to 30 MHz, –3 dB

FM SECTION

• Tuning Range

[U.S.A. and Canada models] ............................ 87.5 to 107.9 MHz

[Other models] .............................................. 87.50 to 108.00 MHz

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf)

• Selectivity (400 kHz) ............................................................... 70 dB

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 76 dB/70 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................. 0.2%/0.3%

• Stereo Separation (1 kHz) ....................................................... 45 dB

• Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB

AM SECTION

• Tuning Range ......................................... 530/531 to 1710/1611 kHz

• Usable Sensitivity ............................................................. 300 µV/m

GENERAL

• Power Supply

[U.S.A. and Canada models] ............................... AC 120 V/60 Hz

[Australia model] ................................................. AC 240 V/50 Hz

[U.K., Europe and Singapore models] ................ AC 230 V/50 Hz

[Korea model] ..................................................... AC 220 V/60 Hz

[China and General models] ..... AC 110/120/220/240 V, 50/60 Hz

• Power Consumption

[U.S.A. and Canada models] .................................. 290 W/370 VA

[Other models] ..................................................................... 290 W

Standby Mode ......................................................... approx. 0.6 W

• AC Outlets

[U.S.A., Canada, Europe and Singapore models]

.......................................................... 2 (Total 100 W maximum)

[China and General models] .................. 2 (Total 50 W maximum)

[U.K. and Australia models] ......................... 1 (100 W maximum)

• Dimension (W x H x D)

.......................... 435 x 161 x 390 mm (17” x 6-7/16” x 15-3/8”)

• Weight ...................................................................... 11.5 kg (25 lbs)

• Accessories ............................................................... Remote control

Batteries

Front VIDEO AUX jack cap

75-ohm/300-ohm antenna adapter (U.K. model)

AM loop antenna

Indoor FM antenna

*Specifications are subject to change without notice.

0111V730_60-67_EN(U) 1/9/02, 6:18 PM66

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V874750

0112V730(U)-cv4 12/27/01, 2:19 PM1

Transcripción de documentos

U RX-V730 AV Receiver OWNER’S MANUAL 0100V730(U)-cv1 1 12/27/01, 2:16 PM SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • 11 Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 12 13 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 14 1 2 3 4 5 6 7 8 9 Read Instructions – All the safety and operating instructions should be read before the product is operated. Retain Instructions – The safety and operating instructions should be retained for future reference. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to. Follow Instructions – All operating and use instructions should be followed. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 15 16 17 18 19 Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, I CAUTION 0101V730_Cau_EN(U) 2 12/27/01, 2:16 PM SAFETY SAFETY INSTRUCTIONS INSTRUCTIONS d) 20 21 22 23 If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 24 Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE FCC INFORMATION (for US customers only) 1. 2. 3. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. CAUTION II 0101V730_Cau_EN(U) 3 12/27/01, 2:16 PM CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 13 To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm. 2 Install this unit in a well ventilated, cool, dry, clean place with at least 30 cm on the top, 20 cm on the left and right, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. 14 Take care of this unit so that no foreign objects and/or liquid drops inside this unit. 15 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons. 16 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. 17 Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty. 18 Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet. 19 VOLTAGE SELECTOR (China and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz. 3 4 5 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. III CAUTION 0101V730_Cau_EN(U) 4 12/27/01, 2:16 PM INTRODUCTION CONTENTS INTRODUCTION CONTENTS ............................................................ 1 FEATURES ............................................................. 2 GETTING STARTED ............................................ 3 Checking the package contents ................................. 3 Installing batteries in the remote control ................... 3 CONTROLS AND FUNCTIONS ......................... 4 PREPARATION SET MENU ........................................................... 41 Adjusting the items on the SET MENU .................. 41 1 SPEAKER SET (speaker mode settings) ............ 42 2 LFE LEVEL ........................................................ 44 3 SP DLY TIME (speaker delay time) ................... 44 4 D. RANGE (dynamic range) ............................... 45 5 L/R BALANCE (balance of the main left and right speakers) ..................................................... 45 6 HP TONE CTRL (headphone tone control) ........ 45 7 INPUT RENAME ............................................... 45 8 I/O ASSIGN (input/output assignment) .............. 46 9 INPUT MODE (initial input mode) .................... 46 10DISPLAY SET .................................................... 46 11 MEM. GUARD (memory guard) ........................ 47 REMOTE CONTROL FEATURES ................... 48 Speakers .................................................................... 9 Speaker placement .................................................... 9 Connecting the speakers .......................................... 10 Control area ............................................................. 48 Setting the manufacturer code ................................. 49 Changing the source name in the display window .. 50 Clearing renamed source names, and setup manufacturer codes ............................................. 51 Controlling other components ................................. 52 CONNECTIONS .................................................. 13 Before connecting components ............................... 13 Connecting video components ................................ 14 Connecting audio components ................................ 16 Connecting the antennas ......................................... 17 Connecting an external amplifier ............................ 18 Connecting an external decoder .............................. 18 Connecting the power supply cords ........................ 19 Turning on the power .............................................. 19 ON-SCREEN DISPLAY (OSD) .......................... 20 SPEAKER MODE SETTINGS .......................... 21 ADJUSTING SPEAKER OUTPUT LEVELS .. 22 Before you begin ..................................................... 22 Using the test tone ................................................... 22 BASIC OPERATION ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS ....................................................... 53 ADDITIONAL INFORMATION SOUND FIELD PROGRAM PARAMETER EDITING .......................................................... 54 ADVANCED OPERATION OSD modes ............................................................. 20 Selecting the OSD mode ......................................... 20 BASIC OPERATION SPEAKER SETUP ................................................. 9 PREPARATION Front panel ................................................................ 4 Remote control .......................................................... 6 Using the remote control ........................................... 7 Front panel display .................................................... 8 INTRODUCTION ADVANCED OPERATION What is a sound field? ............................................. 54 Sound field program parameters ............................. 54 Changing parameter settings ................................... 55 DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS .............................................. 56 TROUBLESHOOTING ...................................... 60 GLOSSARY .......................................................... 64 SPECIFICATIONS .............................................. 66 ADDITIONAL INFORMATION BASIC PLAYBACK ............................................ 24 Input modes and indications .................................... 26 Selecting a sound field program .............................. 27 DIGITAL SOUND FIELD PROCESSING (DSP) ................................................................. 30 Understanding sound fields ..................................... 30 Hi-Fi DSP programs ................................................ 30 CINEMA-DSP ...................................................... 31 Sound design of CINEMA-DSP ............................. 31 CINEMA-DSP programs ........................................ 33 TUNING ................................................................ 35 Automatic and manual tuning ................................. 35 Presetting stations .................................................... 36 Tuning in to a preset station .................................... 38 Exchanging preset stations ...................................... 38 SLEEP TIMER ..................................................... 39 Setting the sleep timer ............................................. 39 Canceling the sleep timer ........................................ 39 English RECORDING ....................................................... 40 1 0102V730_1-8_EN(U) 1 12/27/01, 2:16 PM FEATURES Built-in 6-channel power amplifier Other features ◆ Minimum RMS output power (0.06% THD, 20 Hz – 20 kHz, 8Ω) Main: 75 W + 75 W Center: 75 W Rear: 75 W + 75 W Rear center: 75 W ◆ 96-kHz/24-bit D/A converter ◆ “SET MENU” for optimizing this unit for your Audio/Video system ◆ Test tone generator for easier speaker balance adjustment ◆ 6-channel external decoder input ◆ On screen display function helpful in controlling this unit ◆ S-video signal input/output capability ◆ Component video input/output capability ◆ Optical and coaxial digital audio signal jacks ◆ Sleep timer ◆ Remote control with preset manufacturer codes Multi-mode digital sound field processing ◆ ◆ ◆ ◆ Dolby Pro Logic/Dolby Pro Logic decoder Dolby Digital/Dolby Digital EX decoder DTS/DTS-ES compatible decoder CINEMA DSP: Combination of YAMAHA DSP technology and Dolby Pro Logic, Dolby Digital or DTS ◆ Virtual CINEMA DSP ◆ SILENT CINEMA DSP Sophisticated AM/FM Tuner ◆ 40-Station random access preset tuning ◆ Automatic preset tuning ◆ Preset station shifting capability (Preset editing) ■ About this manual • y indicates a tip for your operation. • Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses. • This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement in operativity ability, and others. In this case, the product has priority. Manufactured under license from Dolby Laboratories. “DTS”, “ES” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. 2 0102V730_1-8_EN(U) 2 12/27/01, 2:16 PM GETTING STARTED INTRODUCTION Checking the package contents Check your package to make sure it contains the following items. Batteries (4) (AAA, R03, UM-4) Remote control TRANSMIT RE–NAME CLEAR AM loop antenna CODE SET SYSTEM STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD PREPARATION POWER SELECT POWER POWER TV AV AMP Front VIDEO AUX jack cap Indoor FM antenna (U.S.A., Canada, China, Korea and General models) 75-ohm/300-ohm antenna adapter (U.K. model) (Europe, U.K., Australia and Singapore models) REC AUDIO DISC SKIP + VOL – LEVEL SET MENU + TITLE TV VOL TV INPUT MUTE MENU A/B/C/D/E TV MUTE SELECT – PRESET CH BASIC OPERATION CH + PRESET TEST ON SCREEN TV VOL STEREO RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT ENTERTAINMENT 1 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 6 7 EFFECT TV SPORTS 5 /DTS SUR. 9 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity markings (+ and –) inside the battery compartment. 1 • Change all of the batteries if you notice a decrease in the operating range of the remote control, that the indicator does not flash, or the light becoming dim. • Do not use old batteries together with new ones. • Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 3 Press the part and slide off the battery compartment cover. 2 Insert the four supplied batteries (AAA, R03, UM-4) according to the polarity markings on the inside of the battery compartment. 3 Slide the cover back on so that it snaps into place. English 1 APPENDIX If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared. 3 0102V730_1-8_EN(U) 3 ADDITIONAL INFORMATION 2 ■ Notes on batteries ADVANCED OPERATION Installing batteries in the remote control 12/27/01, 2:16 PM CONTROLS AND FUNCTIONS Front panel 1 2 3 4 5 6 INPUT 7 VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER RDS MODE/FREQ PRESET/TUNING EON FM/AM EDIT STANDBY /ON PTY SEEK MODE START TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT TREBLE SPEAKERS A VIDEO AUX STEREO B PROGRAM PRESET/TUNING A/B/C/D/E EFFECT – PHONES 8 9 0 RDS MODE/FREQ q w e + – r + S VIDEO VIDEO t AUDIO R OPTICAL y PRESET/TUNING EON L FM/AM EDIT PTY SEEK MODE START TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM ui o p as d f (U.K. and Europe models) 1 STANDBY/ON 4 INPUT MODE Turns this unit on, or set it to the standby mode. When you turn this unit on, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound. Sets the priority for the types of input signals (AUTO, DTS, ANALOG) to receive when one component is connected to two or more input jacks. Priority cannot be set when 6CH INPUT is selected as the input source. Standby mode In this mode, this unit will consume a small amount of power in order to receive infrared-signals from the remote control. 2 Remote control sensor Receives signals from the remote control. 3 Front panel display Shows information about the operational status of this unit. 5 INPUT l / h Selects the input source you want to listen to or watch. 6 VOLUME Controls the output level of all audio channels. This does not affect the OUT (REC) level. 7 6CH INPUT Selects the audio source connected to the 6CH INPUT jacks. This audio takes priority over the source selected with INPUT l / h (or the input selector buttons on the remote control). 4 0102V730_1-8_EN(U) 4 12/27/01, 2:16 PM CONTROLS AND FUNCTIONS 8 9 SPEAKERS A/B u RDS MODE/FREQ (U.K. and Europe models) When an RDS station is received, press this button to change the display mode among the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data service) and/or frequency display mode in turn. Turns the set of main speakers connected to the A and/or B terminals on or off. i PTY SEEK MODE (U.K. and Europe models) Press this button to set the unit in the PTY SEEK mode. 0 STEREO/EFFECT o PTY SEEK START (U.K. and Europe models) Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode. q PROGRAM l / h Selects the DSP program. w PRESET/TUNING l / h e A/B/C/D/E Selects preset station groups A to E. r BASS s TUNING MODE (AUTO/MAN’L MONO) Switches the tuning mode between automatic and manual. d MEMORY (MAN’L/AUTO FM) Stores the current station in the memory. f FM/AM Switches the reception band between FM and AM. ADVANCED OPERATION Adjusts the low-frequency response for the main left and right channels. Turn right to increase or turn left to decrease the lowfrequency response. a PRESET/TUNING (EDIT) Switches the function of PRESET/TUNING l / h between selecting a preset station number and tuning (the colon (:) turns on or off). This button is also used to exchange the assignment of two preset stations with each other. t TREBLE ADDITIONAL INFORMATION Adjusts the high-frequency response for the main left and right channels. Turn right to increase or turn left to decrease the highfrequency response. y VIDEO AUX jacks Inputs for audio and video signals from a portable external source (game console, etc.). Set the input source to V-AUX to enjoy source signals from these jacks. When the VIDEO AUX jacks on the front panel are not used, you can attach the provided front VIDEO AUX jack cap as shown in the illustration. When the cap is not attached, be sure retain it carefully. APPENDIX EO X AU VID AL TIC OP L AU DIO BASIC OPERATION Selects preset station numbers 1 to 8 when the colon (:) appears in the front panel display. Selects the tuning frequency when the colon (:) does not appear. p EON (U.K. and Europe models) Press this button to select the desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to tune in to a radio program of that type automatically. PREPARATION Switches between normal stereo and DSP effect reproduction. When STEREO is selected, 2-channel signals are directed to the main left and right speakers without effect sounds and all Dolby Digital and DTS signals (except the LFE channel) are mixed down to the main left and right speakers. INTRODUCTION SILENT (PHONES jack) Allows you enjoy DSP effect for private listening with headphones. When you connect headphones, no signals are output to the speakers or the OUTPUT jacks. R EO VID IDEO SV English 5 0102V730_1-8_EN(U) 5 12/27/01, 2:16 PM CONTROLS AND FUNCTIONS Remote control This section describes the remote control controls and their functions. Make sure that the AMP mode is selected before starting operation. See “REMOTE CONTROL FEATURES” on pages 48 to 52. 1 2 3 POWER STANDBY SLEEP 6CH INPUT w e r t A B C PHONO y V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD TRANSMIT RE–NAME CLEAR CODE SET SYSTEM 4 5 6 1 Infrared window Outputs infrared control signals. Aim this window at the component you want to operate. 2 TRANSMIT indicator Flashes while the remote control is sending signals. 3 STANDBY Turns on the power of this unit. Sets this unit in the standby mode. 4 SYSTEM POWER 5 Å/ı/Ç Sets the remote control to operate other components (not necessarily connected to this unit) without changing this unit’s input source. 6 Input selector buttons 7 SELECT POWER POWER TV AV u AMP i REC AUDIO DISC SKIP + o 8 TITLE + TV VOL 9 CH – TV MUTE SELECT PRESET MENU ON SCREEN q – d DISPLAY JAZZ CLUB ROCK CONCERT ENTERTAINMENT 1 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 8 9 0 TEST s TV SPORTS /DTS SUR. a STEREO EFFECT HALL Used when changing the setting and to implement the settings. + TV VOL RETURN p CH PRESET TEST 0 9 Multi control section MUTE A/B/C/D/E TV INPUT EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Shows the selected source component that you are controlling. Selects the effect speaker channel to be adjusted. – SET MENU 7 Display window 8 LEVEL VOL LEVEL Select the input source and set the remote control to operate the selected source component. Outputs the test tone to adjust the speaker levels. q DSP program Select DSP programs for the AMP position. Press a button repeatedly to select a DSP program within that group. w RE-NAME Used when changing the input source name in the display window. e CLEAR Used when clearing functions acquired using the rename features, and to set manufacturer codes. r CODE SET Used when setting up the manufacturer code (see page 49). t SLEEP Sets the sleep timer. y 6CH INPUT Selects the audio source connected to the 6CH INPUT jacks. 6 0102V730_1-8_EN(U) 6 12/27/01, 2:16 PM CONTROLS AND FUNCTIONS u SELECT k/n Sets the remote to control a component other than the one selected using the input selector buttons. Using the remote control Switches the function of the same controls between AMP and the component selected using the input selector buttons. INPUT INTRODUCTION i AMP VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT TREBLE SPEAKERS A B VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E EFFECT – PHONES o VOL +/– Increases or decreases the volume level. 30° + – + S VIDEO VIDEO L AUDIO R OPTICAL 30° p MUTE Approximately 6 m (20 feet) CODE SET PREPARATION Mutes the sound. Press again to restore the audio output to the previous volume level. a SET MENU Selects the SET MENU mode. s ON SCREEN Displays the input or operation status. Switches between normal stereo and DSP effect reproduction. When STEREO is selected, 2-channel signals are directed to the main left and right speakers without effect sounds and all Dolby Digital and DTS signals (except the LFE channel) are mixed down to the main left and right speakers. The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation. ■ Handling the remote control ADVANCED OPERATION • Do not spill water or other liquids on the remote control. • Do not drop the remote control. • Do not leave or store the remote control in the following types of conditions: – high humidity or temperature such as near a heater, stove or bath; – dusty places; or – in places subject to extremely low temperatures. BASIC OPERATION d STEREO/EFFECT ADDITIONAL INFORMATION APPENDIX English 7 0102V730_1-8_EN(U) 7 12/27/01, 2:16 PM CONTROLS AND FUNCTIONS Front panel display 1 MATRIX 2 VCR2/DVR DIGITAL VIRTUAL SILENT PRO LOGIC / 3 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO MUTE VOLUME DTS DOLBY DIGITAL PRO LOGIC PS PTY RT CT STEREO AUTO SLEEP MOVIE THTR 12 ENTERTAINMENT EON PTY HOLD TUNED MEMORY VCR1 L DSP dB mS PCM 5 4 6 7 8 9 q w e r t 0 C R LFE RL RC RR y (U.K. and Europe models) 1 Processor indicators 9 Multi-information display Lights up when the t, g, VIRTUAL, PRO LOGIC / or DSP are activated. Shows the current DSP program name and other information when adjusting or changing settings. MATRIX lights up when the Dolby Digital EX decoder or the DTS-ES compatible decoder is activated. 0 RDS indicator (U.K. and Europe models) Flashes while the MUTE function is on. The name(s) of the RDS data offered by the currently received RDS station light(s) up. EON indicator lights up when an RDS station that offers the EON data service is being received. PTY HOLD indicator lights up while searching for stations in the PTY SEEK mode. 4 VOLUME level indicator q STEREO indicator Indicates the volume level. Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the “AUTO” indicator is lit. 2 Input source indicator Shows the current input source with a cursor. 3 MUTE indicator 5 v indicator Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals. w TUNED indicator 6 SILENT indicator e MEMORY indicator Lights up when headphones are connected while the digital sound field processor is on. Flashes to show a station can be stored. 7 Headphones indicator Lights up when headphones are connected. 8 DSP program indicators The name of the selected DSP program lights up when the ENTERTAINMENT, MOVIE THEATER 1, MOVIE THEATER 2 or V/DTS SURROUND DSP program is selected. Lights up when this unit is tuned to a station. r AUTO indicator Shows that this unit is in the automatic tuning mode. t SLEEP indicator Lights up while the sleep timer is on. y Input channel indicator Indicates the channel components of input signals being received. 8 0102V730_1-8_EN(U) 8 12/27/01, 2:16 PM PREPARATION SPEAKER SETUP Speaker placement ■ Use of a subwoofer expands your sound field Rear speaker (R) Subwoofer Main speaker (L) 1.8 m (6 feet) Rear center speaker Rear speaker (L) ■ Main speakers Place the main left and right speakers an equal distance from the ideal listening position. The distance between each speaker and each side of the video monitor should also be the same. ■ Center speaker Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible (such as directly over or under the monitor) and centrally between the main speakers. ■ Rear speakers Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (6 feet) above the floor. ■ Rear center speaker Place the rear center speaker in the center between the rear left and right speakers at the same height from the floor as the rear speakers. ■ Subwoofer Note • If you do not use any of effect speakers (rear, center and/or rear center), change the settings of SPEAKER SET items at the SET MENU to designate the signals to other terminals you connect speakers to. English CAUTION Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor. 9 0103V730_9-18_EN(U) 9 12/27/01, 2:16 PM APPENDIX The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce wall reflections. ADDITIONAL INFORMATION It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low-frequency effect) channel with high fidelity when playing back Dolby Digital or DTS signals. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction. Main speaker (R) ADVANCED OPERATION The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use the models of equivalent performance with the main speakers. Center speaker BASIC OPERATION The main speakers are used for the main source sound plus effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for effect and surround sounds. The center speaker is for the center sounds (dialog, vocals, etc.). The rear center speaker supplements the rear (left and right) speakers and provides for more realistic front-to-back transitions. Refer to the following diagram when you place the speakers. PREPARATION This unit has been designed to provide the best soundfield quality with a 6-speaker system, using main left and right speakers, rear left and right speakers, a center speaker, and a rear center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality. INTRODUCTION Speakers SPEAKER SETUP Connecting the speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. CAUTION • Use speakers with the specified impedance shown on the rear panel of this unit. • Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers. If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers in your configuration after you finish connecting your speakers. ■ Speaker cables A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge. 10 mm (3/8”) 1 2 1 Remove approximately 10 mm (3/8”) of insulation from each of the speaker cables. 2 Twist the exposed wires of the cable together to prevent short circuits. ■ Connecting to the SPEAKERS terminals 2 Red: positive (+) Black: negative (–) 3 1 1 2 Unscrew the knob. 3 Tighten the knob to secure the wire. Insert one bare wire into the hole in the side of each terminal. (U.S.A. model) y Banana plug (U.S.A., Canada, Australia, China, Korea and General models) • Banana plug connections are also possible. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal. (U.S.A. model) ■ MAIN SPEAKERS terminals One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be connected to either the MAIN A or the MAIN B terminals. ■ REAR SPEAKERS terminals A rear speaker system can be connected to these terminals. ■ CENTER SPEAKER terminals A center speaker can be connected to these terminals. ■ REAR CENTER SPEAKER terminals A rear center speaker can be connected to these terminals. 10 0103V730_9-18_EN(U) 10 12/27/01, 2:16 PM SPEAKER SETUP Main B speaker Right Main A speaker Left Right Left Center speaker GND AUDIO R L PHONO + R L COMPONENT VIDEO PB/CB PR/CR GND B Y DVD AC OUTLETS IN MAIN D-TV /CBL SURROUND DVD UNBAL. D-TV /CBL R FM ANT VIDEO MONITOR OUT OUTPUT MAIN A OR B: 8 A+B:16 : 8 CENTER REAR CENTER : 8 : 8 REAR REAR CENTER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER CENTER R L IMPEDANCE SELECTOR 5 4 6 Right 7 Left Rear speaker ADVANCED OPERATION Subwoofer system 3 REAR (SURROUND) SET BEFORE POWER ON BASIC OPERATION 6CH INPUT S VIDEO L OUTPUT L MAIN MAIN A OR B :4 MIN. /SPEAKER A+B :8 MIN. /SPEAKER CENTER :6 MIN. /SPEAKER REAR CENTER :6 MIN. /SPEAKER REAR :6 MIN. /SPEAKER SUB WOOFER REAR (SURROUND) R L R MONITOR OUT DIGITAL OUTPUT + + 75 SUB WOOFER CENTER – – OUT VCR 1 MD/CD-R OPTICAL – TUNER AM ANT DVD – PREPARATION – IN OUT (REC) MD /CD-R IN (PLAY) + A VCR 2 /VDR CD COAXIAL OPTICAL D-TV/CBL CENTER + VIDEO OUT DIGITAL INPUT CD 3 SPEAKERS REAR CENTER L MAIN R VIDEO AUDIO S VIDEO MD/CD-R 2 INTRODUCTION 1 Rear center speaker 1 4 2 ADDITIONAL INFORMATION 5 7 6 The diagram shows the speaker layout in the listening room. When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your SPEAKER SET selections. 11 0103V730_9-18_EN(U) 11 12/27/01, 2:17 PM English Notes • The cut-off frequency of the SUBWOOFER jack is 90 Hz. • If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET item “1E BASS” on the SET MENU to MAIN. • Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 53). APPENDIX ■ SUBWOOFER jack SPEAKER SETUP ■ IMPEDANCE SELECTOR switch WARNING Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when this unit is in the standby mode. Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode. IMPEDANCE SELECTOR switch Switch position Speaker Main MAIN A OR B: 8 A+B:16 : 8 CENTER REAR CENTER: 8 : 8 REAR MAIN A OR B :4 MIN. /SPEAKER A+B :8 MIN. /SPEAKER CENTER :6 MIN. /SPEAKER REAR CENTER :6 MIN. /SPEAKER REAR :6 MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER SET BEFORE POWER ON Impedance level If you use one set of main speakers, the impedance of each speaker must be 4 Ω or higher. If you use two sets of main speakers, the impedance of each speaker must be 8 Ω or higher. IMPEDANCE SELECTOR Left SPEAKERS REAR CENTER L MAIN R + CENTER + + – – A – Center The impedance must be 6 Ω or higher. Rear Center The impedance must be 6 Ω or higher. Rear – – OMPONENT VIDEO R/CR PB/CB B Y REAR (SURROUND) R L Main If you use one set of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two sets of main speakers, the impedance of each speaker must be 16 Ω or higher. [Canada model only] The impedance of each speaker must be 8 Ω or higher. Center The impedance must be 8 Ω or higher. Rear Center The impedance must be 8 Ω or higher. + + R L OUTPUT L R MAIN MAIN A OR B :4 MIN. /SPEAKER A+B :8 MIN. /SPEAKER CENTER :6 MIN. /SPEAKER REAR CENTER :6 MIN. /SPEAKER REAR :6 MIN. /SPEAKER The impedance of each speaker must be 6 Ω or higher. MAIN A OR B: 8 A+B:16 : 8 CENTER REAR CENTER: 8 : 8 REAR REAR CENTER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER CENTER R REAR (SURROUND) L SET BEFORE POWER ON IMPEDANCE SELECTOR (U.S.A. model) Right Rear The impedance of each speaker must be 8 Ω or higher. 12 0103V730_9-18_EN(U) 12 12/27/01, 2:17 PM CONNECTIONS This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. To enjoy multi-channel sound track of DVD software, etc. with DSP effect, you need to make digital connection. All digital input jacks are acceptable for 96-kHz sampling digital signals. CAUTION Do not connect this unit or other components to the mains power until all connections between the components have been completed. Antenna input terminals (page 17) R AUDIO + L VCR 2 /VDR – IN COMPONENT VIDEO PR/CR PB/CB GND DVD D-TV /CBL SURROUND DVD UNBAL. D-TV /CBL FM ANT R SUB WOOFER 6CH INPUT REAR (SURROUND) R L R MAIN L REAR CENTER CENTER R S VIDEO L OUTPUT MONITOR OUT DIGITAL OUTPUT + + MAIN SUB WOOFER CENTER – B Y IN MD/CD-R OPTICAL – – OUT VCR 1 75 MD/CD-R – TUNER AM ANT OUT (REC) MD /CD-R IN (PLAY) + A ADDITIONAL INFORMATION R CD CENTER + VIDEO OUT DIGITAL INPUT CD DVD SPEAKERS REAR CENTER L L PHONO S VIDEO COAXIAL OPTICAL D-TV/CBL MAIN R VIDEO ADVANCED OPERATION AUDIO Speaker terminals (pages 10-11) Video component jacks (pages 14-15) Audio component jacks (page 16) GND BASIC OPERATION DIGITAL INPUT jacks (pages 13-16) Note • The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this unit may not function properly. PREPARATION • Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit. • When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products. • After you have completed all connections, check them again to make sure they are correct. • The name of jack corresponds to input selector. INTRODUCTION ■ Connecting to digital jacks Before connecting components REAR (SURROUND) L VIDEO MONITOR OUT OUTPUT SUBWOOFER OUTPUT jack (page 11) DIGITAL OUTPUT jack (page 16) APPENDIX 6CH INPUT jacks (page 18) AC OUTLETS (page 19) OUTPUT jacks (page 18) English 13 0103V730_9-18_EN(U) 13 12/27/01, 2:17 PM CONNECTIONS Connecting video components Refer to the connection examples on the next page. ■ Types of video jacks There are three types of video jacks as follows: COMPONENT VIDEO S VIDEO VIDEO 2 1 PR/CR PB/CB Y 3 1 VIDEO jack Conventional composite video signal. 2 S VIDEO jack Transmits color and luminance separately and achives high-quality color reproduction. 3 COMPONENT VIDEO jacks Transmit color difference (PB/CB, PR/CR) and luminance separately and provide the best quality picture. • Each type of video jack works independently. Signals input through the composite video, S-video and component jacks are only output through the corresponding composite video, S-video, and component jacks. • Use a commercially available cable specified for connecting each type of jacks. • The description of the component video jacks may differ depending on the component (e.g. Y, CB, CR/Y, PB, PR/Y, B-Y, R-Y etc.). When using these jacks, refer also to the operation instructions for the component being connected. ■ Connecting a video monitor Connect the video input jack on your video monitor to the MONITOR OUT VIDEO jack. Note • If you connect this unit with a source component using S-video (or Component video) jacks, you also need to connect your video monitor using S-video (or Component video) jacks. ■ Connecting a DVD player/digital TV/cable TV Connect the optical digital audio signal output jack on your component to the DIGITAL INPUT jack and connect the video signal output jack on the component to the VIDEO jack on this unit. Then connect AUDIO jacks on your component to the AUDIO jacks on this unit. y • If your video component has an S-video output or component video output, connect the S-video signal output jack on the component to the S VIDEO jack or connect the component video signal output jacks on the component to the COMPONENT VIDEO jacks. • The AUDIO jacks are available for a video component which does not have optical digital output jack. However, multichannel reproduction cannot be obtained with audio signals input from AUDIO jacks. ■ Connecting a game console or camcorder Connect the optical digital audio signal output jack on your video component to the OPTICAL jack on the front panel and connect video signal output jack on the component to the VIDEO jack on the front panel. y • If your video component has an S-video output, connect the Svideo signal output jack on the component to the S VIDEO jack. • The AUDIO jacks are available for a video component such as a camcorder which does not have optical digital output jack. ■ Connecting a VCR or DVR (digital video recorder) Connect the audio signal input jacks on your video component to the AUDIO OUT jacks and connect the video signal input jack on the video component to the VIDEO OUT jack on this unit for picture recording. Connect the audio signal output jacks on your component to the AUDIO IN jacks and connect the video signal output jack on the component to the VIDEO IN jack on this unit to play a source from your recording component. Second VCR or digital video recorder can be connected using VCR 2/DVR jacks. y • If your video component has an S-video input, connect the Svideo signal input jack on the component to the S VIDEO OUT jack. • If your video component has an S-video output, connect the Svideo signal output jack on the component to the S VIDEO IN jack. Notes • Once you have connected a recording component to this unit, keep its power turned on while using this unit. If the power is off, this unit may distort the sound from other components. • S-video and component video signals pass independently through this unit’s video circuit. Make sure to connect this unit to both a source component and a recording component using the video jacks of the same system. 14 0103V730_9-18_EN(U) 14 12/27/01, 2:17 PM CONNECTIONS O VCR 1 AUDIO INPUT R L GND AUDIO R VIDEO INPUT L VIDEO OUTPUT VIDEO OUTPUT V R INTRODUCTION AUDIO OUTPUT TV/digital TV/ cable TV OPTICAL OUTPUT V V VIDEO AUDIO L PHONO S VIDEO VIDEO PREPARATION OUT DIGITAL INPUT CD R L VCR 2 /VDR IN CD TUNER AM ANT COAXIAL OPTICAL D-TV/CBL OUT VCR 1 DVD OUT (REC) MD /CD-R IN (PLAY) MD/CD-R MAIN D-TV /CBL SURROUND DVD COMPONENT VIDEO PB/CB PR/CR GND Y DVD IN 75 UNBAL. D-TV /CBL FM ANT MONITOR OUT SUB WOOFER CENTER DIGITAL OUTPUT VIDEO S VIDEO 6CH INPUT MONITOR OUT OUTPUT BASIC OPERATION MAIN A OR B :4 MIN. /SPEAKER A+B :8 MIN. /SPEAKER CENTER :6 MIN. /SPEAKER REAR CENTER :6 MIN. /SPEAKER REAR :6 MIN. /SPEAKER SUB WOOFER MD/CD-R OPTICAL V V R L VIDEO INPUT VIDEO OUTPUT AUDIO OUTPUT ADVANCED OPERATION O OPTICAL OUTPUT DVD player Video monitor INPUT VOLUME INPUT M0DE PRESET/TUNING ADDITIONAL INFORMATION 6CH INPUT FM/AM EDIT TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS TREBLE VIDEO AUX A/B/C/D/E + – + S VIDEO VIDEO L AUDIO R APPENDIX – OPTICAL indicates signal direction VIDEO OUTPUT Game console or camcorder indicates left analog cables R indicates right analog cables O indicates optical cables V indicates video cables O OPTICAL OUTPUT 15 0103V730_9-18_EN(U) 15 12/27/01, 2:17 PM English V L CONNECTIONS Notes Connecting audio components • Once you have connected a recording component to this unit, keep its power turned on while using this unit. If the power is off, this unit may distort the sound from other components. • DIGITAL OUTPUT jack and analog OUT (REC) jacks are independent. Only digital signals are output from DIGITAL OUTPUT jack and analog signals from OUT (REC) jacks. ■ Connecting a CD player Connect the coaxial digital output jack on your CD player to the DIGITAL INPUT CD jack. y ■ Connecting a turntable • The AUDIO jacks are available for a CD player which does not have coaxial digital output jack. Connect the output jacks on your turntable to the PHONO jacks. PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or MC-head amplifier when connecting to these jacks. ■ Connecting a CD recorder or MD recorder Connect the optical digital signal input jack on your CD recorder or MD recorder to the DIGITAL OUTPUT MD/ CD-R jack for digital recording. Connect the optical digital output jack on your CD recorder or MD recorder to the DIGITAL INPUT MD/ CD-R jack to play a source from your recording component. y • Connect your turntable to the GND terminal to reduce noise in the signal. Please note that this connection may increase noise with some record players. y • The AUDIO jacks are available for an CD recorder or MD recorder which does not have optical digital input or output jack. OUTPUT L R Turntable GND GND AUDIO R AUDIO VIDEO L PHONO S VIDEO COAXIAL OUTPUT C CD player R L VCR 2 /VDR IN CD COAXIAL OPTICAL D-TV/CBL VIDEO OUT DIGITAL INPUT CD TUNER AM ANT OUT VCR 1 DVD OUT (REC) MD /CD-R IN (PLAY) MD/CD-R MAIN D-TV /CBL SURROUND DVD GND IN 75 OPTICAL OUTPUT FM ANT O O CD recorder or MD recorder OPTICAL INPUT SUB WOOFER MD/CD-R OPTICAL SUB WOOFER CENTER DIGITAL OUTPUT 6CH INPUT S VIDEO OUTPUT VIDEO MONITOR OUT indicates signal direction L indicates left analog cables R indicates right analog cables C indicates coaxial cables O indicates optical cables 16 0103V730_9-18_EN(U) 16 12/27/01, 2:17 PM UNBAL. CONNECTIONS Connecting the antennas ■ Connecting the AM loop antenna Set up the AM loop antenna, then connect it. 2 Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals. 3 Orient the AM loop antenna for the best reception. Connect each antenna correctly to the designated terminals. AM loop antenna (included) Indoor FM antenna (included) EO VIDEO TUNER AM ANT PREPARATION 1 INTRODUCTION Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. GND DVD 75 UNBAL. BASIC OPERATION D-TV /CBL FM ANT MONIT OUT VIDEO R OUT FREQUENCY STEP Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. 11 (7/16) 8 (5/16) 6 (1/14) Cut the external sleeve of the 75-ohm coaxial cable and prepare it for connection. 3 Lead wire A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas. FREQUENCY STEP switch (China and General models) Because the interstation frequency spacing FM/AM differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area. North, Central and South America: 100 kHz/10 kHz Other area: 50 kHz/9 kHz Before setting this switch, disconnect the AC power plug of this unit from the AC outlet. 50kHz/9kHz Cut the lead wire and remove it. Clamp with pliers. 5 Clamp with pliers. Insert the wire into the slot. Snap the cover into place. 100kHz/10kHz FREQUENCY STEP English Insert the cable wire into the slot, and clamp it with pliers. 17 0103V730_9-18_EN(U) 17 APPENDIX 4 ADDITIONAL INFORMATION Open the cover of the included 75-ohm/300-ohm antenna adapter. Unit: mm (inch) • The AM loop antenna should be placed away from this unit. • The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. ADVANCED OPERATION Notes 75-ohm/300-ohm antenna adapter (U.K. model) 1 2 12/27/01, 2:17 PM CONNECTIONS Connecting an external amplifier If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows. Note • When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, signals are output from the SPEAKERS terminals as well. 1 2 3 4 Connecting an external decoder This unit is equipped with 6 additional input jacks (MAIN left and right, CENTER, SURROUND left and right and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor, or pre-amplifier. Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels. Notes OUTPUT SUB WOOFER L R MAIN REAR CENTER CENTER OUTPUT R REAR (SURROUND) L 5 • When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs. • When you select 6CH INPUT as the input source, settings of “1 SPEAKER SET” on the SET MENU do not apply (except for “1F MAIN Lv”). 1 SUBWOOFER jack When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your SPEAKER SET selections. Notes • The cut-off frequency of the SUBWOOFER jack is 90 Hz. • If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the settings of SPEAKER SET item “1E BASS” on the SET MENU. • Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 53). 2 MAIN jacks Main channel line output jacks. Note • The signals output through these jacks are affected by the BASS and TREBLE settings. 3 REAR CENTER jack Rear center channel line output jack. 4 CENTER jack Center channel line output jack. 5 REAR (SURROUND) jacks Rear channel line output jacks. 18 0103V730_9-18_EN(U) 18 12/27/01, 2:17 PM CONNECTIONS Connecting the power supply cords Turning on the power VOLTAGE SELECTOR 1 INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE VOLTAGE SELECTOR MEMORY INTRODUCTION When all connections are complete, turn on the power of this unit. AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT TREBLE SPEAKERS A B VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E EFFECT + – + S VIDEO VIDEO L AUDIO R PREPARATION – PHONES OPTICAL AC OUTLETS SWITCHED 120V 60Hz 100W MAX. TOTAL TRANSMIT RE–NAME CLEAR CODE SET SYSTEM 1 POWER STANDBY SLEEP 6CH INPUT PHONO A B C V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD SELECT ■ Connecting the AC power cord Plug in this unit to the wall outlet. POWER TV AV AMP REC 1 ■ AC OUTLETS (SWITCHED) Press STANDBY/ON (SYSTEM POWER on the remote control) to turn on the power of this unit. SYSTEM POWER STANDBY /ON or Front panel Remote control The level of the main volume, and then the current DSP program name appear on the front panel display. 2 ADDITIONAL INFORMATION Turn on the video monitor connected to this unit. ADVANCED OPERATION U.S.A., Canada, China, Europe, Singapore and General models .............................................. 2 OUTLETS U.K. and Australia model ................................ 1 OUTLET Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLETS is controlled by this unit’s STANDBY/ON (or SYSTEM POWER and STANDBY). These outlets will supply power to any source component connected to this unit whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLETS varies depending on the area which it was purchasing. China and General models ......................................... 50 W Other models ........................................................... 100 W POWER BASIC OPERATION (General model) ■ VOLTAGE SELECTOR (China and General models) APPENDIX The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/ 220/240 V AC, 50/60 Hz. English 19 0104V730_19-23_EN(U) 19 12/27/01, 2:17 PM ON-SCREEN DISPLAY (OSD) You can display operational information for this unit on a video monitor. If you display the SET MENU and DSP program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display. Selecting the OSD mode SELECT y POWER POWER TV AV AMP 2 REC AUDIO DISC SKIP • If a video source is playing, the OSD is superimposed over the video image. • The OSD signal is not output to the OUT (REC) jack, and will not be recorded with any video signal. • You can set the OSD to turn on (blue background) or off when there is no video signal by using “10 DISPLAY SET” on the SET MENU (see page 46). OSD modes You can select the amount of information the shown in the on-screen display. Full display This mode shows the DSP program parameter settings continuously on the video monitor. Short display This mode briefly shows the front panel display message at the bottom of the screen and then disappears. Display off This mode briefly shows “DISPLAY OFF” at the bottom of the screen and then disappears. In this mode, no operational information will be shown on the monitor, except when ON SCREEN is pressed. P01 CONCERT HALL INIT.DLY…………45ms ROOM SIZE…………1.O LIVENESS…………………5 P01 CONCERT HALL Full display VOL – LEVEL TITLE SET MENU + TV VOL CH – TV MUTE SELECT PRESET + ON SCREEN TV VOL – STEREO 3 DISPLAY EFFECT 1 Turn on the video monitor connected to this unit. 2 3 Press AMP. Press ON SCREEN on the remote control repeatedly to change the display mode. The OSD mode changes in the following order: full display, short display, and display off. Notes • If your video monitor is connected only to the COMPONENT VIDEO jacks of this unit, the OSD is not shown. Make sure to connect your video monitor to the COMPONENT VIDEO jacks and either VIDEO or S VIDEO jacks if you want to see the OSD. • Playing back video software that has an anti-copy signal or video signals with a lot of noise may produce unstable images. (When using two video monitors) • If you select video source from a component connected to both the S VIDEO IN and composite VIDEO IN jacks, and both S VIDEO OUT and composite VIDEO OUT jacks are connected to two different monitors, the OSD appears only the monitor connected with S-video jacks. When there is no video signal input from source component, the OSD appears on both monitors. Short display • When you choose the full display mode, INPUT l / h, VOLUME and some other types of operational information are displayed at the bottom of the screen in the same format as the front panel display. • The SET MENU and test tone display appear regardless of the OSD mode. 20 20 CH PRESET TEST RETURN MUTE MENU A/B/C/D/E TV INPUT y 0104V730_19-23_EN(U) + 12/27/01, 2:17 PM SPEAKER MODE SETTINGS If the initial settings shown in the following table are not appropriate for your speaker configuration, see “1 SPEAKER SET” on pages 42-44 to change the settings. INTRODUCTION This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings as well as other possible settings. Summary of SPEAKER SET items 1A through 1F Description Possible settings (default setting indicated in bold) Sets center speaker availability and size. LRG/SML/NON 1B MAIN Sets main speaker size. LARGE/SMALL 1C REAR LR Sets rear L/R speakers availability and size. LRG/SML/NON 1D REAR CT Sets rear center speaker availability and size. LRG/SML/NON 1E BASS Sets the speaker(s) to be used to output low bass signals. 1F MAIN Lv Sets the main speaker level. SWFR/MAIN/BOTH Nrm (Normal)/–10 dB BASIC OPERATION 1A CENTER PREPARATION Item ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 21 0104V730_19-23_EN(U) 21 12/27/01, 2:17 PM ADJUSTING SPEAKER OUTPUT LEVELS This section explains how to adjust speaker output levels using the test tone generator. When this adjustment is complete, the output level heard at the listening position should be the same from each speaker. This is important for best performance of the digital sound field processor, and the various decoders (Dolby Digital, Dolby Pro Logic, Dolby Pro Logic and DTS). Using the test tone Use the test tone to balance the output levels of the speakers. The adjustment of each speaker output level should be made at your listening position using the remote control. 3 Note • Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone. INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM Before you begin BASS SILENT TREBLE SPEAKERS A B VIDEO AUX PROGRAM STEREO A/B/C/D/E PRESET/TUNING EFFECT – PHONES INPUT + – + S VIDEO VIDEO L AUDIO R OPTICAL VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY SELECT AUTO/MAN'L MONO MAN'L/AUTO FM BASS TREBLE SPEAKERS SILENT A POWER POWER TV AV AMP VIDEO AUX PROGRAM STEREO B PRESET/TUNING A/B/C/D/E EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R AUDIO DISC SKIP + VOL – LEVEL TITLE 2 3 4 SET MENU + TV VOL CH – TV MUTE SELECT Turn on the video monitor connected to this unit. 2 Press SPEAKERS A or B to select the main speakers to be used. If you are using two sets of the main speakers, press both A and B. 3 – TREBLE + – + CH + ON SCREEN TV VOL – STEREO DISPLAY EFFECT 1 Press AMP to select the AMP mode. “AMP” appears in the display window on the remote control. 2 Press TEST to output the test tone. SPEAKERS A B Set the BASS and TREBLE controls on the front panel to the center position. BASS 2,5 MENU PRESET TEST RETURN 3 3 MUTE A/B/C/D/E TV INPUT PRESET 1 1 REC OPTICAL AMP TEST RETURN Adjust the volume of this unit so you can hear the test tone. The test tone is heard (in order) from the main left speaker, center speaker, main right speaker, rear right speaker, rear center, rear left speaker, and the subwoofer. The tone is produced for 2.5 seconds from each speaker. VOLUME + or VOL – Front panel 22 0104V730_19-23_EN(U) 22 12/27/01, 2:17 PM Remote control ADJUSTING SPEAKER OUTPUT CONNECTIONS LEVELS LEFT RIGHT 4 *SUBWOOFER + TV VOL CH TV MUTE SELECT – PRESET CH + INTRODUCTION CENTER Adjust the level of the effect speakers using j / i so that it matches the level of the main speakers. While adjusting, the test tone is heard from the selected speaker. PRESET TV VOL – Note RIGHT SURROUND 5 REAR CENTER * Subwoofer test tone is output after the rear left speaker (LEFT SURROUND). TEST DOLBY SUR. LEFT Note • If the test tone cannot be heard, turn down the volume, set this unit to standby mode and check the speaker connections. Notes • If “1A CENTER” on the SET MENU is set to NON, the center channel sound is automatically output from the main left and right speakers. • If “1C REAR LR” on the SET MENU is set to NON, the output level of the rear left, right and center speakers cannot be adjusted in step 4. The test tone will be circulated skipping the rear left and right speakers and the rear center speaker. • If “1D REAR CT” on the SET MENU is set to NON, the output level of the rear center speaker cannot be adjusted in step 4. The test tone will be circulated skipping the rear center speaker. • If “1E BASS” on the SET MENU is set to MAIN, the test tone will be circulated skipping the subwoofer. y ADDITIONAL INFORMATION • It is not necessary to readjust the speaker levels once they are set (as long as you do not change the speakers). You can enjoy listening to or watching the input source at the desired volume simply by adjusting the VOLUME knob (or VOL +/– on the remote control). • If the output level of the effect speakers (center, rear left, rear right, and rear center) cannot be increased enough to match the level of the main speakers, set “1F MAIN Lv” on the SET MENU to –10 dB (see page 44). This setting decreases the main speaker output level to about one-third of the normal level. After you have set “1F MAIN Lv” on the SET MENU to –10 dB, adjust the levels for the center and rear speakers again. ADVANCED OPERATION The front panel display also shows which speaker is outputting the test tone. TEST RETURN BASIC OPERATION For your convenience, the state of the test tone output is also shown on the monitor by an image of an audio listening room. When adjustment is complete, press TEST to stop the test tone. PREPARATION LEFT SURROUND • To adjust the level of the main speakers, use VOLUME knob (or VOL +/– on the remote control). APPENDIX English 23 0104V730_19-23_EN(U) 23 12/27/01, 2:17 PM BASIC PLAYBACK 1 4 6 4 INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY 4 Press INPUT l / h repeatedly (one of the input selector buttons on the remote control) to select the input source. The selected input source name and input mode appear on the front panel display for a few seconds. AUTO/MAN'L MONO MAN'L/AUTO FM BASS A A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD TREBLE SPEAKERS SILENT VIDEO AUX PROGRAM STEREO B PRESET/TUNING A/B/C/D/E INPUT EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R OPTICAL or 3 4 1 6 7 TRANSMIT RE–NAME CLEAR Front panel CODE SET SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO TV AV REC AUDIO 4 V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD DISC SKIP + VCR2/DVR 6 VCR1 V-AUX D-TV/CBL MD/CD-R TUNER CD PHONO VOLUME TITLE POWER TV AV SET MENU + – AMP A/B/C/D/E Selected input source CH TV MUTE SELECT + PRESET PRESET TEST ON SCREEN TV VOL REC STEREO RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT ENTERTAINMENT 1 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 EFFECT TV SPORTS 5 /DTS SUR. 9 6 7 8 7 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Press STANDBY/ON (SYSTEM POWER on the remote control) to turn on the power. To select the audio source connected to the 6CH INPUT jacks (When combining with a video source) • You need to select the input to which the video source component is connected before selecting audio source. Press 6CH INPUT until “6CH INPUT” appears on the front panel display. 6CH INPUT 6CH INPUT SYSTEM POWER STANDBY /ON or or Front panel Front panel R MUTE MENU TV VOL TV INPUT CH POWER L – SELECT Remote control Remote control 2 Turn on the video monitor connected to this unit. 3 Press SPEAKERS A or B to select the main speakers to be used. If you are using two sets of main speakers, press both A and B. SPEAKERS A B Note • If “6CH INPUT” is shown on the front panel display, no other source can be played. To select another input source, first press 6CH INPUT to turn off “6CH INPUT” from the front panel display. 24 0105V730_24-29_EN(U) DVD VOL LEVEL 1 Remote control 24 12/27/01, 2:17 PM BASIC PLAYBACK 5 The BGV function allows you to enjoy video images from a video source together with sounds from an audio source. For example, you can enjoy listening to classical music while having beautiful scenery from a video source on the video monitor. Select a source from the video group, then select a source from the audio group using the input selector buttons on the remote control. BGV selections cannot be made with INPUT l / h on the front panel. VOLUME A B C V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD PHONO PREPARATION Adjust the volume to the desired level. The volume level is displayed digitally. Example: –70 dB Control range: VOLUME MUTE (minimum) to 0 dB (maximum) The volume level indicator also shows the current volume level as a bar graph. If desired, use BASS and TREBLE. These controls only effect the sound from the main speakers. ■ BGV (background video) function + or VOL ■ To mute the sound – BASS TREBLE – + Front panel y • You can also cancel mute by pressing VOL +/–, etc. • During muting, the “MUTE” indicator flashes on the front panel display. Notes HALL PROGRAM or ROCK CONCERT 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 9 Press STANDBY/ON (STANDBY on the remote control) to set this unit in the standby mode. STANDBY or STANDBY /ON Front panel Remote control ENTERTAINMENT 1 TV SPORTS /DTS SUR. 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX APPENDIX Front panel JAZZ CLUB 1 ADDITIONAL INFORMATION Select a DSP program if desired. Use PROGRAM l / h (DSP program buttons on the remote control) to select a DSP program. See pages 30 to 34 for details about DSP programs. When using the remote control, press AMP before selecting a DSP program. ■ When you have finished using this unit ADVANCED OPERATION • If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the center and rear speakers may not match that of the main left and right speakers. • If you have connected a recording component to the VCR 1 OUT, VCR 2/DVR OUT, or MD/CD-R OUT jacks, and you notice distortion or low volume during playback of other components, try turning the recording component on. 7 MUTE Press MUTE on the remote control. To resume the audio output, press MUTE again. BASIC OPERATION + – 1 Remote control INTRODUCTION 6 Start playback or select a broadcast station on the source component. Refer to the operation instructions for the component. Remote control English 25 0105V730_24-29_EN(U) 25 12/27/01, 2:17 PM BASIC PLAYBACK ■ Notes on 96-kHz sampling digital signals Input modes and indications This unit comes with a variety input jacks. You can select the type of input signals you desire. Each time you turn on the power of this unit, the input mode is set according to “9 INPUT MODE” setting on the SET MENU (see page 46 for details). 1 Press INPUT MODE (the input selector button that you have pressed to select the input source on the remote control) repeatedly until the desired input mode is shown on the front panel display. INPUT MODE A B C V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD PHONO or Front panel VCR2/DVR VCR1 Remote control V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME DVD AUTO L R Input mode AUTO: In this mode, the input signal is selected automatically as follows: 1) Digital signal 2) Analog signal DTS: In this mode, only the digital input signal encoded with DTS is selected, even if another signal is input at the same time. ANALOG: In this mode, only the analog input signal is selected, even if a digital signal is input at the same time. Notes • When AUTO is selected, this unit automatically determines the type of signal. If this unit detects a Dolby Digital or DTS signal, the decoder automatically switches to the appropriate setting. • When playing a disc encoded with Dolby Digital or DTS on some LD or DVD players, the sound output delays for a moment when playback resumes after a search because the digital signal is selected again. • When playing a LD source that has not been digitally recorded, the sound may not be output for some LD players. In this case, set the input mode to ANALOG. The digital input jacks of this unit can handle 96-kHz sampling digital signals. Note the following when 96-kHz sampling digital signal is input to this unit: – DSP programs cannot be selected. – Sound will be output as 2-channel stereo from only the main left and right speakers. (There may be sound output from the subwoofer depending on the SPEAKER MODE settings on the SET MENU.) Therefore, the level of the effect speakers cannot be adjusted while listening to such a source. ■ Notes on playing DTS-CD/LDs • If the digital output data of the player has been processed in any way, you may not be able to perform DTS decoding even if you make a digital connection between this unit and the player. • If you play a source encoded with a DTS signal and set the input mode to ANALOG, this unit may reproduce the noise of an unprocessed DTS signal. In this case, connect the source to a digital input jack and set the input mode to AUTO or DTS. • If you switch the input mode to ANALOG while playing a source encoded with a DTS signal, this unit reproduces no sound. • If you play a source encoded with a DTS signal with the input mode set to AUTO; – This unit automatically switches to the DTSdecoding mode (The “t” indicator lights up) after having detected the DTS signal. When playback of the DTS source is completed, the “t” indicator may flash. While this indicator is flashing, only DTS source can be played. If you want to play a normal PCM source soon, set the input mode back to AUTO. – When the input mode is set to AUTO and a search or skip operation is performed during playback of a DTS source, the “t” indicator may flash. If this status continues for longer than 30 seconds, this unit will automatically switch from “DTS-decoding” mode to PCM digital signal input mode. The “t” indicator will turn off. 26 0105V730_24-29_EN(U) 26 12/27/01, 2:17 PM BASIC PLAYBACK 3 Selecting a sound field program INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING EDIT STANDBY /ON TUNING MODE HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 ENTERTAINMENT FM/AM MEMORY 5 6 7 8 AUTO/MAN'L MONO MAN'L/AUTO FM /DTS SUR. BASS A VIDEO AUX PROGRAM STEREO B 9 A/B/C/D/E PRESET/TUNING 10 11 12 0 +10 CHP/INDEX EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R OPTICAL RE–NAME CLEAR PREPARATION Program name PROGRAM l / h TRANSMIT EX/ES SELECT TREBLE SPEAKERS SILENT VCR2/DVR CODE SET VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME SYSTEM POWER STANDBY SLEEP PRO LOGIC / 6CH INPUT TV B C PHONO TUNER MD/CD-R CD MOVIE THTR 1 AV DSP A V-AUX INTRODUCTION You can enhance your listening experience by selecting a DSP program. For details about each program, see pages 30 to 34. After selecting the desired program, press the same button repeatedly to select the desired sub-program if available. Example: Pressing MOVIE THEATER 1 repeatedly switches the sub-program between “Sci-Fi” and “Spectacle”. REC AUDIO DISC SKIP DGTLzSci-Fi L C R LFE RL RR + VOL D-TV/CBL VCR 1 VCR2/DVR DVD – LEVEL TITLE AV – AMP Notes A/B/C/D/E CH TV MUTE SELECT + PRESET ON SCREEN TV VOL STEREO RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 REC EFFECT /DTS SUR. 9 ENTERTAINMENT 2,3 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX 1 Press AMP. 2 Press one of the DSP program buttons on the remote control to select the desired program. The name of the selected program appears on the front panel display. AMP HALL ROCK CONCERT JAZZ CLUB ENTERTAINMENT 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 /DTS SUR. 9 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Program name VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME DSP MOVIE THTR 1 DGTL Spectacle Sub-program name L C R LFE RL RR y • You can also select DSP program by pressing PROGRAM l / h on the front panel. • Select a program based on your listening preference. Program names are just for reference. APPENDIX PRO LOGIC / ADDITIONAL INFORMATION 1 TV SPORTS ADVANCED OPERATION • There are 9 programs with sub-programs available with this unit. However, the selection depends on the input signal format and not all sub-programs can be used with all input signal formats. • The digital sound field processor cannot be used when a source connected to the 6CH INPUT jacks of this unit is selected or when 96-kHz sampling digital signals are input to this unit. • The acoustics of your listening room affect the DSP program. Minimize the sound reflections in your room to maximize the effect created by the program. • When you select an input source, this unit automatically selects the last DSP program used with that source. • When you set this unit in the standby mode, the current source and DSP program are memorized and are automatically selected when you turn on the power again. • If a Dolby Digital or DTS signal is input when the input mode is set to AUTO, the DSP program (No. 7–9) automatically switches to the appropriate decoding program. • When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/Enhanced, or PRO LOGIC Movie, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. (If “1A CENTER” on the SET MENU is set to NON, the center channel sound is output from the main speakers.) PRESET TEST 1 Sub-program name MENU TV VOL TV INPUT CH POWER TV + MUTE BASIC OPERATION SELECT POWER SET MENU English 27 0105V730_24-29_EN(U) 27 12/27/01, 2:17 PM BASIC PLAYBACK ■ Selecting PRO LOGIC 4 You can enjoy the 2-channel sources decoded into five or six discrete channels by selecting PRO LOGIC in program No. 9. INPUT Press SELECT repeatedly to select the decoder; PRO LOGIC or PRO LOGIC . HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 VOLUME INPUT M0DE 6 7 ENTERTAINMENT 8 6CH INPUT /DTS SUR. NATURAL SOUND AV RECEIVER 9 PRESET/TUNING FM/AM EX/ES SELECT 10 11 12 0 +10 CHP/INDEX EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS TREBLE SPEAKERS SILENT A VIDEO AUX PROGRAM STEREO B 5 A/B/C/D/E PRESET/TUNING EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R OPTICAL PROGRAM l / h TRANSMIT RE–NAME CLEAR HALL CODE SET SYSTEM POWER STANDBY SLEEP After selecting on the decoder (PRO LOGIC ), select the mode appropriate for the source by pressing q/DTS SUR. The selection switches as follow; PRO LOGIC Movie ↔ PRO LOGIC Music JAZZ CLUB TV A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD AV REC AUDIO + DISC SKIP 3 4 MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 LEVEL TITLE POWER TV AV SET MENU + – AMP + – y ROCK CONCERT JAZZ CLUB • You can select PRO LOGIC, PRO LOGIC Movie, and PRO LOGIC Music by pressing PROGRAM l / h on the front panel repeatedly. ENTERTAINMENT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 /DTS SUR. 3,4,5 9 CHP/INDEX STEREO DISPLAY EFFECT HALL 12 +10 MUTE PRESET ON SCREEN TV VOL 2 11 0 CH TV MUTE SELECT TEST RETURN 10 A/B/C/D/E PRESET REC 6 7 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX 1 Select a 2-channel source and start playback on the source component. 2 Press AMP. 3 Press q/DTS SUR. The previously selected sub program appears on the front panel display. AMP HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 6 7 5 /DTS SUR. 9 ENTERTAINMENT 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Remote control V-AUX D-TV/CBL DVD MD/CD-R PRO LOGIC TUNER CD PHONO VOLUME PRO LOGIC / DSP PRO LOGIC L R 28 0105V730_24-29_EN(U) 28 8 EX/ES SELECT MENU TV VOL TV INPUT CH POWER 9 – SELECT VCR1 ENTERTAINMENT 2 MONO MOVIE /DTS SUR. VOL VCR2/DVR ROCK CONCERT 1 TV SPORTS 6CH INPUT 12/27/01, 2:17 PM BASIC PLAYBACK ■ Playing Dolby Digital Surround EX or DTS ES software ■ SILENT CINEMA DSP The MATRIX indicator lights up. EX/ES 12 CHP/INDEX MATRIX VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER DIGITAL MOVIE THTR 1 DSP Spectacle EX AUTO: Matrix6.1: ■ Normal stereo reproduction 1 Press STEREO to turn off the sound effect for normal stereo reproduction. Press STEREO again to turn the sound effect back on. STEREO STEREO or EFFECT EFFECT Front panel Remote control BASIC OPERATION OFF: This mode automatically switches Dolby Digital EX and DTS-ES compatible depending on the signal. Rear center speaker does not work for 5.1 channel sources. This setting produces 6-channel playback of the input source using the Dolby Digital EX or DTS-ES compatible decoder. The rear center speaker can be used when playing a 5.1-channel source. Rear center speaker does not work in this setting. (Except for when the DSP program “6ch” is selected.) Notes • This feature is not available when 6CH INPUT is selected or 96-kHz sampling digital signals are input to this unit. • The sound of LFE channel will be mixed and output from the headphone. PREPARATION The display changes AUTO → Matrix6.1 → OFF each time the EX/ES button is pressed. You can enjoy a powerful sound field similar to what you could expert from actual speakers with SILENT CINEMA DSP. You can listen to SILENT CINEMA DSP by connecting your headphones to the PHONES jack while the digital sound field processor is on. Enjoy all the DSP program using the headphones. The “SILENT” indicator lights up on the front panel display. (When sound effects are off, you listen to the source with normal stereo reproduction.) INTRODUCTION Press EX/ES to turn on the Dolby Digital EX or DTS-ES compatible decoder. Notes With Virtual CINEMA DSP, you can enjoy all DSP programs without rear speakers. It creates virtual speakers to reproduce a natural sound field. You can listen to virtual CINEMA DSP by setting “1C REAR LR” in the SET MENU to NON. Sound field processing changes to VIRTUAL CINEMA DSP automatically. y During stereo reproduction, you can display information such as the type, format and sampling frequency of the signal input from the components connected to this unit. (While playing a source) 1 2 Press AMP. Press d to display the information about the input signal. + TV VOL – TV MUTE SELECT English CH PRESET CH + PRESET TV VOL – 29 0105V730_24-29_EN(U) 29 APPENDIX Note • This unit is not set in the virtual CINEMA DSP mode even if “1C REAR LR” is set to NON in the following cases: – when the 6ch Stereo, DOLBY DIGITAL Normal, Pro Logic Normal, Pro Logic , or DTS Normal program is selected; – when the sound effect is turned off; – when 6CH INPUT is selected as the input source; – when 96-kHz sampling digital signals are input to this unit; – when using the test tone; or – when connecting the headphones. ADDITIONAL INFORMATION ■ Virtual CINEMA DSP Notes • If you turn off the sound effects, no sound is output from the center speaker, rear speakers, or rear center speaker. • If you turn off the sound effects while a Dolby Digital or DTS signal is being output, the dynamic range of the signal is automatically compressed and the sounds of the center and rear speaker channels are mixed and output from the main speakers. • The volume may be greatly reduced when you turn off the sound effects or if you set “4 D. RANGE” on the SET MENU to MIN. In this case turn on the sound effect. • The sound of LFE channel will be directed to the main left and right or the subwoofer (or both) channels depending on the setting of “1E BASS” on the SET MENU. ADVANCED OPERATION • No sound will be output from the rear center speaker if you have set “1C REAR LR” or “1D REAR CT” on the SET MENU to NON. • The setting becomes AUTO once this unit turns into standby mode. • Some Dolby Digital Surround EX or DTS ES software may not contain the signal that is necessary for this unit to switch to the Dolby Digital EX or DTS-ES compatible decoding mode. To turn on the decoder when playing such a source, select “Matrix6.1”. 12/29/01, 9:37 PM DIGITAL SOUND FIELD PROCESSING (DSP) Understanding sound fields A sound field is defined as the “characteristic sound reflections of a particular space.” In concert halls and other music venues, we hear early reflections and reverberations as well as the direct sound produced by the artist(s). The variations in the early reflections and other reverberations among the different music venues is what gives each venue its special and recognizable sound quality. YAMAHA sent teams of sound engineers all around the world to measure the sound reflections of famous concert halls and music venues, and collect detailed sound field information such as the direction, strength, range, and delay time of those reflections. Then we stored this enormous amount of data in the ROM chips of this unit. ■ Recreating a sound field Recreating the sound field of a concert hall or an opera house requires localizing the virtual sound sources in your listening room. The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound field. YAMAHA’s DSP requires four effect speakers to recreate sound fields based on the measured sound field data. The processor controls the strength and delay time of the signals output from the four effect speakers to localize the virtual sound sources and fully encompass the listener. Hi-Fi DSP programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. No. Program Features 1 CONCERT HALL A large round concert hall with a rich surround effect. Pronounced reflections from all directions emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual seat is near the center, close to the stage. 2 JAZZ CLUB This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club, that seats up to 300 people. Its wide left to right seating arrangement offers a real and vibrant sound. 3 ROCK CONCERT The ideal program for lively, dynamic rock music. The data for this program was recorded at LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall. 4 ENTERTAINMENT/ Disco This program recreates the acoustic environment of a lively disco in the heart of a big city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. ENTERTAINMENT/ 6ch Stereo Using this program increases the listening position range. This is a sound field suitable for background music at parties, etc. 30 0106V730_30-34_EN(U) 30 12/27/01, 2:17 PM CINEMA-DSP BASIC OPERATION L SURROUND SOUND FIELD PRESENCE SOUND FIELD DIALOG EFFECT PREPARATION Filmmakers intend for the dialog to be located right on the screen, the effect sound a little farther back, the music spread even farther back, and the surround sound around the listener. Of course, all of these sounds must be synchronized with the images on the screen. CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field programs to provide a surround sound field. It recreates comprehensive movie sound design in your audio room. In CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the Main left and right, and Center channels, so the listener can enjoy realistic dialogue, depth of sound, smooth transition between sound sources, and a surround sound field that goes beyond the screen. When a DTS or Dolby Digital signal is detected, the CINEMA-DSP sound field processor automatically chooses the most suitable sound field program for that signal. INTRODUCTION Sound design of CINEMA-DSP MUSIC ADVANCED OPERATION R SURROUND SOUND FIELD ADDITIONAL INFORMATION In addition to the DSP, this unit is equipped with a variety of precise decoders; Dolby Pro Logic decoder for Dolby Surround sources, Dolby Pro Logic decoder for Dolby Surround and 2-channel sources, Dolby Digital/DTS decoder for multi-channel sources and Dolby Digital EX or DTS-ES compatible decoder for adding a rear center channel. You can select CINEMA-DSP programs to optimize these decoders and the DSP sound patterns depending on the input source. APPENDIX English 31 0106V730_30-34_EN(U) 31 12/27/01, 2:17 PM CINEMA-DSP The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without using matrix processing. This unit’s MOVIE THEATER programs provide the same quality of sound and sound localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality sound designed for movie theaters into your home. With this unit’s MOVIE THEATER programs, you can use Dolby Digital or DTS technology to recreate a dynamic sound that gives you the feeling of being in a public theater. ■ Dolby Digital/DTS + DSP sound field effect These programs use YAMAHA’s tri-field DSP processing on each of the Dolby Digital or DTS signals for the front, left surround, and right surround channels. This processing enables this unit to reproduce the immense sound field and surround expression of a Dolby Digitalor DTS-equipped movie theater without sacrificing the clear separation of all channels. Presence DSP sound field Left surround DSP sound field Right surround DSP sound field ■ Dolby Digital EX/DTS-ES compatible + DSP sound field effect These programs provide you with the maximum experience of the spacious surround effects by adding an extra rear center DSP sound field created from the rear center channel. ■ Dolby Pro Logic + DSP sound field effect Most movie software has 4-channel (left, center, right, and surround) sound information encoded by Dolby Surround matrix processing and stored on the left and right tracks. These signals are processed by the Dolby Pro Logic decoder. The MOVIE THEATER programs are designed to recreate the spaciousness and delicate nuances of sound that tend to be lost in the encoding and decoding processes. Presence DSP sound field Surround DSP sound field ■ Dolby Pro Logic Dolby Pro Logic decodes Dolby Surround software into 5 discrete full-range channels (3 channels in front and 2 channels in rear). There are 2 modes; MOVIE for movies and MUSIC for 2-channel audio sources. 32 0106V730_30-34_EN(U) 32 12/27/01, 2:17 PM CINEMA-DSP CINEMA-DSP programs INTRODUCTION ■ For movie programs: No. 7 to 9 This unit automatically chooses the appropriate decoder and DSP sound field pattern according to the input signal format. Table of Program Names for Each Input Format Input 5.1 channel 6.1 channel * DOLBY DIGITAL DTS DOLBY DIGITAL EX DTS-ES compatible 7 8 9 MOVIE THEATER 1 70 mm Spectacle DGTL Spectacle DTS Spectacle Spectacle EX Spectacle ES 70 mm Sci-Fi DGTL Sci-Fi DTS Sci-Fi Sci-Fi EX Sci-Fi ES MOVIE THEATER 2 70 mm Adventure DGTL Adventure DTS Adventure Adventure EX Adventure ES 70 mm General DGTL General DTS General General EX General ES — Normal — Dolby D EX — — Enhanced — Enhanced EX — — — Normal — DTS-ES — — Enhanced — Enhanced ES Normal — — — — Enhanced — — — — Movie — — — — Music — — — — DOLBY DIGITAL DTS DIGITAL SUR PRO LOGIC ADVANCED OPERATION PRO LOGIC BASIC OPERATION Stereo Program PREPARATION No. 2 channel * means the Dolby Digital EX decoder or the DTS-ES compatible decoder is ON. • If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will automatically switch to the Dolby Digital playback sound field or DTS playback sound field. • If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the EX/ES button on the remote control, the Dolby Digital EX or DTS-ES compatible decoder usually turns on and the corresponding DSP program is selected. • EX/ES on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with the rear center speaker. In this case the program name changes to the corresponding name for 6.1 channel. • When playing a 6.1 channel source with the Dolby Digital EX decoder or the DTS-ES compatible decoder turned off, the program name changes to the corresponding name for 5.1 channel. APPENDIX Notes • The “ ” indicator does not light up when selecting program No. 9 except in Enhanced mode. • When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, main and rear speakers output effect sounds. ADDITIONAL INFORMATION y English 33 0106V730_30-34_EN(U) 33 12/27/01, 2:18 PM CINEMA-DSP The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. Select the DSP program that you feel sounds best regardless of the name and description given for it below. No. 7 8 Features Program MOVIE THEATER 1 MOVIE THEATER 2 9 Spectacle This program creates the extremely wide sound field of a 70-mm movie theater. It precisely reproduces the source sound in detail, making both the video and the sound field incredibly real. This is ideal for any kind of video source encoded with Dolby Surround, Dolby Digital or DTS (especially large-scale movie productions). Sci-Fi This program clearly reproduces dialog and sound effects in the latest sound form of science fiction films, thus creating a broad and expansive cinematic space amid the silence. You can enjoy science fiction films in a virtual-space sound field that includes Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced techniques. Adventure This program is ideal for precisely reproducing the sound design of the newest 70-mm and multichannel soundtrack films. The sound field is made to be similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. General This program is for reproducing sounds from 70-mm and multichannel soundtrack films, and is characterized by a soft and extensive sound field. The presence sound field is relatively narrow. It spatially spreads all around and toward the screen, restraining the echo effect of conversations without losing clarity. Enhanced Mode This program ideally simulates the multi-surround speaker systems of the 35-mm film theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital sound field processing create precise effects without altering the original sound orientation. The surround effects produced by this sound field wrap around the viewer naturally from the back to the left and right, and toward the screen. ■ For audio-video sources: No. 4 to 6 No. 4 Program Features ENTERTAINMENT/ Game This program adds a deep and spatial feeling to video game sounds. ENTERTAINMENT/ Concert Video This program adds a deep and spatial feeling to concert video sounds. 5 TV SPORTS With this program, you can enjoy watching various TV programs such as news, variety shows, music programs or sports programs. In a stereo broadcast of a sports game, the commentator is oriented at the center position, and the shouts and the atmosphere in the stadium spread on the surround side, while their spread to the rear is properly restrained. 6 MONO MOVIE This program is provided for reproducing monaural video sources (such as old movies). The program produces the optimum reverberation to create sound depth by using only the presence sound field. 34 0106V730_30-34_EN(U) 34 12/27/01, 2:18 PM TUNING There are 2 ways to tune; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. Press PRESET/TUNING l / h once to begin automatic tuning. Press h to tune in to a higher frequency, or press l to tune in to a lower frequency. PRESET/TUNING /DVR ■ Automatic tuning VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER TUNED A AM 144O INTRODUCTION 4 Automatic and manual tuning 1 When tuned in to a station, the “TUNED” indicator lights up and the frequency of the received station is shown on the front panel display. VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM y EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT A B • Use the manual tuning method if the tuning search does not stop at the desired station because the signal is weak. TREBLE SPEAKERS VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E PREPARATION INPUT EFFECT – PHONES + – 1 S VIDEO VIDEO L AUDIO R OPTICAL ■ Manual tuning If the signal from the station you want to select is weak, you must tune in to it manually. 33 2 1 Select TUNER and the reception band following steps 1 and 2 described in “Automatic tuning” at left. 2 Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator goes off from the front panel display. Press INPUT l / h (TUNER on the remote control) to select TUNER as the input source. INPUT SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD or ADVANCED OPERATION TUNING MODE Front panel AUTO AUTO/MAN'L MONO Goes off If the colon (:) appears on the front panel display, press PRESET/TUNING (EDIT) to turn it off. Remote control 2 Press FM/AM to select the reception band. “FM” or “AM” appears on the front panel display. PRESET/TUNING /DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R BASIC OPERATION 4 + TUNER TUNED FM/AM EDIT 3 Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator lights up on the front panel display. 3 A AM 144O Press PRESET/TUNING l / h to tune in to the desired station manually. Hold down the button to continue the tuning search. PRESET/TUNING ADDITIONAL INFORMATION or TUNING MODE AUTO Lights up AUTO/MAN'L MONO Note PRESET/TUNING VCR1 /DVR V-AUX D-TV/CBL DVD MD/CD-R • Manually tuning in to an FM station will automatically change the reception mode to monaural to increase the signal quality. TUNER TUNED EDIT A AM APPENDIX If the colon (:) appears on the front panel display, press PRESET/TUNING (EDIT) to turn it off. 144O English 35 0107V730_35-40_EN(U) 35 12/27/01, 2:18 PM TUNING Notes Presetting stations ■ Automatically presetting stations (for FM stations) You can use the automatic preset tuning feature to store FM stations. This function enables this unit to automatically tune in to FM stations with strong signals, and to store up to 40 (8 stations x 5 groups) of those stations in order. This feature enables you to easily tune in to any preset station by selecting the preset station number (see page 38). INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT TREBLE SPEAKERS A B VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R OPTICAL 23 1 1 Press FM/AM to select the FM band. FM/AM 2 Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator lights up on the front panel display. TUNING MODE AUTO AUTO/MAN'L MONO 3 • Any stored station data existing under a preset number is cleared when you store a new station under that preset number. • When a station data is stored under a preset number, the frequency and reception band are also stored. • You can manually replace a preset station with another FM or AM station by simply following the procedure in the section “Manually presetting stations” on page 37. • If the number of the received stations does not reach E8, automatic preset tuning has automatically stopped after searching all stations. • Only FM stations with sufficient signal strength are stored automatically by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in the monaural mode, and store it by following the procedure in “Manually presetting stations” on page 37. Lights up Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds. The preset number and the “MEMORY” and “AUTO” indicators flash. Then, after about 5 seconds, automatic preset tuning begins from the frequency currently displayed toward the higher frequencies. Automatic preset tuning options You can select the preset number from which this unit will store FM stations and/or begin tuning toward lower frequencies. After pressing MEMORY in step 3: 1. Press A/B/C/D/E and PRESET/TUNING l / h to select the preset number under which the first station will be stored. Automatic preset tuning will stop when stations have all been stored up to E8. 2. Press PRESET/TUNING (EDIT) to turn off the colon (:) and then press PRESET/TUNING l to begin tuning toward lower frequencies. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the preset stations may be cleared. If so, store the stations again. MEMORY MAN'L/AUTO FM VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER AUTO MEMORY A1:FM CD PHONO VOLUME L R When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station. 36 0107V730_35-40_EN(U) 36 12/27/01, 2:18 PM TUNING ■ Manually presetting stations 4 You can also store up to 40 stations (8 stations x 5 groups) manually. VOLUME 6CH INPUT PRESET/TUNING INTRODUCTION INPUT INPUT M0DE NATURAL SOUND AV RECEIVER Press PRESET/TUNING l / h to select a preset station number (1 to 8) while the “MEMORY” indicator is flashing. Press h to select a higher preset station number. Press l to select a lower preset station number. PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS SILENT TREBLE SPEAKERS A B VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E EFFECT – PHONES + – + S VIDEO VIDEO L AUDIO R OPTICAL VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME TUNED MEMORY 1 C3:AM 63O kHz 2,5 5 Tune in to a station. See page 35 for tuning instructions. VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME TUNED A AM 63O kHz L R Press MEMORY (MAN’L/AUTO FM) on the front panel while the “MEMORY” indicator is flashing. MEMORY The station band and frequency MAN'L/AUTO FM appear on the front panel display with the preset group and number you have selected. VCR2/DVR 2 R VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME Press MEMORY (MAN’L/AUTO FM). The “MEMORY” indicator flashes for about 5 seconds. TUNED C3:AM 63O kHz L R Shows the displayed station has been stored as C3. BASIC OPERATION When tuned in to a station, the front panel display shows the frequency of received station. L PREPARATION 4 3 MEMORY MEMORY 6 MAN'L/AUTO FM Press A/B/C/D/E repeatedly to select a preset station group (A to E) while the “MEMORY” indicator is flashing. The group letter appears and make sure that the colon (:) appears on the front panel display. • Any stored station data existing under a preset number is cleared when you store a new station under that preset number. • The reception mode (stereo or monaural) is stored along with the station frequency. ADVANCED OPERATION Notes Flashes 3 Repeat steps 1 to 5 to store other stations. A/B/C/D/E VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD ADDITIONAL INFORMATION VCR2/DVR PHONO VOLUME TUNED MEMORY C :AM 63O kHz L R APPENDIX English 37 0107V730_35-40_EN(U) 37 12/27/01, 2:18 PM TUNING Tuning in to a preset station Exchanging preset stations You can tune any desired station simply by selecting the preset station number under which it was stored. INPUT You can exchange the assignment of two preset stations. The example below describes the procedure for exchanging preset station “E1” with “A5”. VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY PRESET/TUNING FM/AM AUTO/MAN'L MONO MAN'L/AUTO FM EDIT STANDBY /ON BASS SILENT A B TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM TREBLE SPEAKERS VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E BASS – + – + S VIDEO VIDEO L AUDIO R TREBLE SPEAKERS SILENT EFFECT PHONES A OPTICAL B VIDEO AUX STEREO PROGRAM PRESET/TUNING A/B/C/D/E EFFECT – PHONES 2 1 LEVEL TITLE CH – 1,3 1,3 MENU CH TV MUTE SELECT + PRESET TEST STEREO ON SCREEN TV VOL RETURN 1 2 A/B/C/D/E PRESET – DISPLAY ROCK CONCERT 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 9 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX VIDEO L AUDIO R OPTICAL 2,4 2 Press and hold PRESET/TUNING (EDIT) for more than 3 seconds. “E1” and the “MEMORY” indicator flash on the front panel display. Press A/B/C/D/E (A/B/C/D/E on the remote control) to select the preset station group. The preset group letter appears on the front panel display and changes each time you press A/B/C/D/E. VCR2/DVR PRESET/TUNING VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER or E1:FM 87.5 EDIT MHz MENU 3 A/B/C/D/E Front panel Remote control Press PRESET/TUNING l / h (PRESET j / i on the remote control) to select a preset station number (1 to 8). The preset group and number appear on the front panel display along with the station band, frequency and the “TUNED” indicator lights up. + CH TV MUTE SELECT – PRESET Front panel VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD PHONO VOLUME TUNED MEMORY A5:FM 9O.6 MHz PRESET/TUNING or Tune in to preset station “A5” by using the A/B/C/D/E and PRESET/TUNING l / h. “A5” and the “MEMORY” indicator flash on the front panel display. VCR2/DVR 4 TV VOL CH + L R Press PRESET/TUNING (EDIT) again. The stations stored at the two preset assignments are exchanged. PRESET TV VOL VCR2/DVR – PRESET/TUNING Remote control EDIT VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER MEMORY EDIT E1-A5 Shows the exchange of stations has been completed. VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD TUNED E1:FM 87.5 MHz 38 0107V730_35-40_EN(U) CD TUNED MEMORY SET MENU A/B/C/D/E 2 S VIDEO Tune in to preset station “E1” by using the A/B/C/D/E and PRESET/TUNING l / h. See “Tuning in to a preset station” at left. ENTERTAINMENT 1 TV SPORTS /DTS SUR. 1 JAZZ CLUB + 1 EFFECT HALL – MUTE SET MENU + TV VOL TV INPUT + 38 12/27/01, 2:18 PM CD SLEEP TIMER Canceling the sleep timer 1 The sleep timer can only be set with the remote control. y Press SLEEP repeatedly until “SLEEP OFF” appears on the front panel display. After a few seconds, “SLEEP OFF” disappears, the “SLEEP” indicator goes off and the display returns to the previous indication. INTRODUCTION Use this feature to automatically set this unit in the standby mode after the amount of time you have set. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off the external component(s) connected to AC OUTLET(S). SLEEP • The sleep timer setting can also be canceled by setting this unit in the standby mode by using STANDBY on the remote control (or STANDBY/ON on the front panel) or by disconnecting the AC power cord from the AC outlet. Setting the sleep timer TRANSMIT RE–NAME CLEAR y CODE SET 2 SYSTEM STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD BASIC OPERATION POWER 1 SELECT POWER POWER TV AV PREPARATION • By connecting a commercially available timer to this unit, you can also set a wake-up timer. Refer to the operation instructions of the timer. AMP REC Select a source and start playback on the source component. 2 Press SLEEP repeatedly to set the amount of time. Each time you press SLEEP, the front panel display changes as shown below. VCR1 V-AUX D-TV/CBL DVD SLEEP MD/CD-R TUNER CD SLEEP SLEEP DSP PCM 3 12Omin ADDITIONAL INFORMATION VCR2/DVR ADVANCED OPERATION 1 PHONO VOLUME L R VCR2/DVR VCR1 V-AUX D-TV/CBL DVD MD/CD-R TUNER CD SLEEP DSP PCM CONCERT HALL APPENDIX The “SLEEP” indicator lights up on the front panel display soon after the sleep timer has been set. The display then returns to the previous indication. PHONO VOLUME L R English 39 0107V730_35-40_EN(U) 39 12/27/01, 2:18 PM RECORDING Recording adjustments and other operations are performed from the recording components. Refer to the operation instructions for these components. 1 2 INPUT VOLUME INPUT M0DE 6CH INPUT NATURAL SOUND AV RECEIVER PRESET/TUNING FM/AM EDIT STANDBY /ON TUNING MODE MEMORY AUTO/MAN'L MONO MAN'L/AUTO FM BASS TREBLE SPEAKERS SILENT A B VIDEO AUX STEREO PROGRAM A/B/C/D/E PRESET/TUNING EFFECT – PHONES TRANSMIT RE–NAME CLEAR + – + S VIDEO VIDEO L AUDIO R OPTICAL CODE SET If you playback a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. SYSTEM 2 POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD ■ Special considerations when recording DTS software SELECT POWER POWER TV AV AMP REC 1 Turn on the power of this unit and all connected component. 2 Select the source component you want to record from. A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD INPUT or Notes • Do a test recording before you start an actual recording. • When this unit is set in the standby mode, you cannot record between the components connected to this unit. • The setting of BASS, TREBLE, VOLUME, “5 L/R BALANCE” on the SET MENU and DSP programs does not effect the recorded material. • A source connected to the 6CH INPUT jacks on this unit cannot be recorded. • A given input source is not output to the same OUT (REC) channel. (For example, the signal input from VCR 1 IN is not output to VCR 1 OUT.) • Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources that have DTS signals recorded on them, the following considerations and adjustments need to be made. For LDs, DVDs and CDs encoded with DTS, when your player is compatible with the DTS format, follow its operation instruction to make a setting so that the analog signal will be output from the player. ■ Timer playback/recording Front panel Remote control 3 Start playback (or select a broadcast station) on the source component. 4 Start recording on the recording component. This unit can perform playback or recording with an external timer (not supplied). Refer to the operating instructions for the component and the timer to be used. Notes • Stored data, such as input source, will be reflected when playback or recording with the timer. • If you do not want any sound output when recording with a timer, turn the volume down. Memory back-up The memory back-up circuit prevents the stored data (input source, volume level, set menu settings and so on) from being lost even if this unit is disconnected from the AC outlet. However, if the timer is turned off for more than one week, the stored data will be lost. 40 0107V730_35-40_EN(U) 40 12/27/01, 2:18 PM ADVANCED OPERATION SET MENU INTRODUCTION The SET MENU consists of 11 items including the speaker mode setting. Choose the appropriate item and adjust or select the values as necessary. Adjusting the items on the SET MENU y • You can adjust the items on the SET MENU while playing a source. • We recommend that you adjust the items on the SET MENU while using a video monitor. Adjustment should be made with the remote control. TRANSMIT RE–NAME CLEAR CODE SET REC AUDIO SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD DISC SKIP + VOL – LEVEL TITLE D-TV/CBL VCR 1 VCR2/DVR • The indication on the front panel display is an abbreviation of the OSD. DVD SET MENU + TV VOL TV INPUT CH – A/B/C/D/E CH TV MUTE SELECT + PRESET SELECT 2 3,6 MUTE MENU PRESET TEST ON SCREEN TV VOL RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT STEREO EFFECT Items Initial settings POWER POWER TV AV AMP REC 1 AUD O 2 LFE LEVEL SP/HP 0 dB 3 SP DLY TIME CENTER REAR CNTR 0 ms 3 ms 4 D. RANGE SP/HP MAX 5 L/R BALANCE 0 dB for L/R 6 HP TONE CTRL BASS/TRBL 0 dB 7 INPUT RENAME 8 I/O ASSIGN 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 8 9 10 11 12 0 +10 CHP/INDEX Note • Some items require extra steps. 1 Press AMP. 2 Press SET MENU to enter the SET MENU. AMP SET MENU 1/3 MENU A/B/C/D/E 3 [A] DVD [B] D-TV/CBL (1) MD/CDR C (optical input) (2) MD/CDR (3) DVD (4) D-TV/CBL D (coaxial input) (5) CD INPUT MODE AUTO Press u/d repeatedly to select the item you want to adjust (1 to 11). + – TV MUTE SELECT PRESET 9 10 DISPLAY SET BLUE BACK OSD SHIFT DIMMER AUTO 0 0 11 MEM. GUARD OFF CH + PRESET 1 ≥ 2 3 4 TV VOL SPEAKER SET LFE LEVEL SP DELAY TIME DYNAMIC RANGE / : Up/Down </> : Enter – y • By pressing SET MENU repeatedly, you can select items in the same order as when pressing d. 4 Press j / i once to enter the setup mode of the selected item. The last setting you adjusted appears on the video monitor and/or on the front panel display. + 2 LFE LEVEL TV VOL – TV MUTE SELECT PRESET CH ≥ SPEAKER………………0dB HEADPHONE…………0dB English CH • In the descriptions for each item from the following page, the default setting is indicated in bold. SET MENU 1/3 TV VOL CH SPEAKER SET LFE LEVEL SP DELAY TIME DYNAMIC RANGE / : Up/Down </> : Enter + PRESET TV VOL – 41 0108V730_41-47_EN(U) 41 APPENDIX B (optical output) ≥ 1 2 3 4 ADDITIONAL INFORMATION A (component video input) EX/ES SELECT SET MENU — 4,5 ADVANCED OPERATION LRG (large) LARGE LRG (large) LRG (large) BOTH Nrm (Normal) 1 TV SPORTS /DTS SUR. 1 ENTERTAINMENT BASIC OPERATION SPEAKER SET A CENTER B MAIN C REAR LR D REAR CT E BASS F MAIN Lv PREPARATION Note 12/27/01, 2:18 PM SET MENU Depending on the item, press u/d to select a sub item. + 2 LFE LEVEL TV VOL CH PRESET SPEAKER………………0dB ≥ HEADPHONE…………0dB CH TV MUTE SELECT – + PRESET TV VOL Press j / i repeatedly to change the setting of the item. + 2 LFE LEVEL TV VOL SPEAKER………………0dB ≥ HEADPHONE……-11dB CH CH TV MUTE SELECT – + PRESET PRESET TV VOL – 6 Press u/d repeatedly until the menu disappears or simply press one of the DSP program group buttons to exit SET MENU. + TV VOL CH – TV MUTE SELECT PRESET Use this feature to select suitable output modes for your speaker configuration. Notes – 5 1 SPEAKER SET (speaker mode settings) HALL CH + or – ENTERTAINMENT 3 4 MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 9 TV VOL ROCK CONCERT 2 MONO MOVIE /DTS SUR. PRESET JAZZ CLUB 1 TV SPORTS 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, if the power cord is disconnected from the AC outlet, or the power supply is cut for more than one week, the stored data will be lost. If so, adjust the items again. • When 96-kHz sampling digital signals are input to this unit, some items are not affected. • When 6CH INPUT is selected as the input source, level adjustments in items 1A through 1E are not affected. ■ 1A CENTER (center speaker mode) By adding a center speaker to your speaker configuration, this unit can provide better dialog localization for several listeners and superior synchronization of sound and images. Choices: LRG (large), SML (small), NON (none) LRG Select this if you have a large center speaker. The entire range of the center channel signal is directed to the center speaker. SML Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center channel are directed to the speakers selected with “1E BASS”. NON Select this if you do not have a center speaker. All of the center channel signal are directed to the main left and right speakers. 42 0108V730_41-47_EN(U) 42 12/27/01, 2:18 PM SET MENU ■ 1B MAIN (main speaker mode) Choices: LARGE, SMALL SMALL Select this if you have small main speakers. The lowfrequency signals (90 Hz and below) of the main channel are directed to the speakers selected with “1E BASS”. Choices: LRG (large), SML (small), NON (none) SML Select this if you have small rear left and right speakers. The low-frequency signals (90 Hz and below) of the rear channel are directed to the speakers selected with “1E BASS”. NON Select this if you do not have rear speakers. • This unit is set in the virtual CINEMA DSP mode when you select NON for “1C REAR LR”. In this case, the rear center speaker will automatically be set to “NON” and the “1D REAR CT” item will be skipped. SML Select this if you have a small rear center speaker. The low-frequency signals (90 Hz and below) of the rear center channel are directed to the speakers selected with “1E BASS”. NON Select this if you do not have a rear center speaker. All of the rear center channel signal are directed to the rear left and right speakers. ■ 1E BASS (LFE/bass out mode) LFE signals carry low-frequency effects when this unit decodes a Dolby Digital or DTS signal. Low-frequency signals are defined as 90 Hz and below. The Lowfrequency signals can be directed to both main left and right speakers, and the subwoofer (subwoofer can be used for both stereo reproduction and the DSP program). Choices: SWFR (subwoofer), MAIN, BOTH SWFR Select this if you use a subwoofer. The LFE signals are directed to the subwoofer. BOTH The LFE signals are directed to the subwoofer. Lowfrequency signals designated to the main channels in accordance with other speaker mode settings are directed to both main speakers and a subwoofer. APPENDIX Note • When you select MAIN for “1E BASS”, the low-frequency signals (90 Hz and below) of the main channel are directed to the main speakers even if you select SMALL for the main speaker mode. ADDITIONAL INFORMATION MAIN Select this if you do not use a subwoofer. The LFE signals are directed to the main speakers. ADVANCED OPERATION y LRG Select this if you have a large rear center speaker. The entire range of the rear center channel signal is directed to the rear center speaker. BASIC OPERATION LRG Select this if you have large rear left and right speakers or if a rear subwoofer is connected to the rear speakers. The entire range of the rear channel signal is directed to the rear left and right speakers. Choices: LRG (large), SML (small), NON (none) PREPARATION ■ 1C REAR LR (rear speaker mode) By adding a rear center speaker to your speaker configuration, this unit can provide more realistic frontto-back and transitions. INTRODUCTION LARGE Select this if you have large main speakers. The entire range of the main left and right channel signal is directed to the main left and right speakers. ■ 1D REAR CT (rear center speaker mode) English 43 0108V730_41-47_EN(U) 43 12/27/01, 2:18 PM SET MENU ■ 1F MAIN Lv (main level mode) Change this setting if you cannot match the output level of the center, rear (L/R), and rear center speakers with the main speakers because of unusually high-efficiency performance from the main speakers. Choices: Nrm (Normal), –10 dB Nrm Select this if you can match the output level of your effect speakers with that of your main speakers when using the test tone. –10 dB Select this if you cannot match the output level of your effect speakers with that of your main speakers when using the test tone. 2 LFE LEVEL Use this feature to adjust the output level of the LFE (low-frequency effect) channel when playing back a Dolby Digital or DTS signal. The LFE signal carries the low-frequency special effect sound which is only added to certain scenes. Control range: SPEAKER ............ –20 to 0 dB HEADPHONE ..... –20 to 0 dB Initial setting: 0 dB 1 Press d/u to select the item to be adjusted. 2 Press j to adjust the LFE level. 3 SP DLY TIME (speaker delay time) Use this feature to adjust the delay of the center and the rear center channel sounds. This feature works when there is sound output from the center speakers, with a source like Dolby Digital or DTS, etc. Ideally, the center speaker and the rear center speaker should be the same distance from the main listening position as the left and right speakers. However, in most home situations, the center speaker or the rear center speaker are placed in line with the main speakers or the rear speakers. By delaying the sound from the center speaker and the rear center speaker, the apparent distance from the center speaker and the rear center speaker to the main listening position can be adjusted to make it seem the same as the distance between the main left and right speaker, and the rear left and right speakers to the listening position. Adjusting the delay time for the center speaker is especially important for giving depth to the dialogue. Control range: CENTER .......................... REAR CNTR (center) ...... Initial setting: CENTER .......................... REAR CNTR (center) ...... 1 0 to 5 ms 0 to 30 ms 0 ms 3 ms Press j / i to increase or decrease the delay of the center and the rear center channel sounds. 3 SP DELAY TIME ≥ CENTER…………………0ms REAR CNTR…………3ms Note • Adjust the LFE level according to the capacity of your subwoofer or headphones. Center speaker image C L RL C R RC RR RC y • Increasing the delay by 1 ms simulates moving the speakers about 30 cm (one foot) farther away from the listening position. 44 0108V730_41-47_EN(U) 44 12/27/01, 2:18 PM SET MENU 4 D. RANGE (dynamic range) Use this feature to change the name of the input which appears on the OSD or the front panel display. 1 Choices: MAX, STD (standard), MIN (minimum) Press an input selector button to select the input you want to change the name of. MAX Select the “MAX” for feature films. 7 INPUT RENAME DVD ≥ STD Select the “STD” for general use. </> : Position / : Character 2 Press j / i to place the _ (under-bar) under the space or the character you want to edit. 5 L/R BALANCE (balance of the main left and right speakers) 7 INPUT RENAME DVD ≥ Control range: 20 steps for L/R Initial setting: 0 dB for L/R 1 </> : Position / : Character 3 Press i to decrease the output level for the main left speaker. Press j for the main right speaker. Press u/d to select the character you want to use and j / i to move to the next one. • Press d to change the character in the following order, or press u to go in the reverse order. A to Z, a space, 0 to 9, a space, a to z, a space, #, *, +, and so on. • Follow the foregoing procedure to rename other inputs. 7 INPUT RENAME Use this feature to adjust the level of the bass and treble when you use your headphones. DVD ≥ DVD1 ADDITIONAL INFORMATION </> : Position / : Character –6 to +3 –6 to +3 0 dB 0 dB ADVANCED OPERATION 6 HP TONE CTRL (headphone tone control) Control range (dB): BASS ............... TRBL (treble) .. Initial setting: BASS ............... TRBL ............... DVD BASIC OPERATION Use this feature to adjust the balance of the output level from the main left and right speakers. PREPARATION MIN Select the “MIN” for listening to sources at low volume levels. DVD INTRODUCTION Use this feature to adjust the dynamic range. This setting is effective only when this unit is decoding Dolby Digital signals. 7 INPUT RENAME Note • You can use up to 8 characters to rename the inputs. 4 Press i repeatedly to exit from INPUT RENAME. APPENDIX English 45 0108V730_41-47_EN(U) 45 12/27/01, 2:18 PM SET MENU 8 I/O ASSIGN (input/output assignment) It is possible to assign jacks according to the component to be used if this unit’s COMPONENT VIDEO input jack or DIGITAL INPUT/OUTPUT jack settings (component names for jacks) differ from that component. This makes it possible to change the jack assignment and effectively connect more components. Once you assign, you can select that component with INPUT l / h (or the input selector buttons on the remote control). ■ 8A CMPNT-V INPUT for COMPONENT VIDEO INPUT jacks [A] and [B] Choices: [A] DVD, V-AUX, VCR 2/DVR, VCR 1, D-TV/CBL [B] DVD, V-AUX, VCR 2/DVR, VCR 1, D-TV/CBL 9 INPUT MODE (initial input mode) Use this feature to designate the input mode for sources connected to the DIGITAL INPUT jacks when you turn on this unit (see page 26 for details about the input mode). Choices: AUTO, LAST AUTO Select this to allow this unit to automatically detect the type of input signal and select the appropriate input mode. LAST Select this to set this unit to automatically select the last input mode used for the respective source. 10 DISPLAY SET 10 DISPLAY SET ■ 8B OPTICAL OUT for OPTICAL OUTPUT jack (1) Choices: (1) MD/CD-R, CD, PHONO, V-AUX, VCR 2/DVR, VCR 1, D-TV/CBL, DVD ■ 8C OPTICAL IN for OPTICAL INPUT jacks (2) to (4) Choices: (2) MD/CD-R, CD, PHONO, VCR 2/DVR, VCR 1, D-TV/CBL, DVD (3) MD/CD-R, CD, PHONO, VCR 2/DVR, VCR 1, D-TV/CBL, DVD (4) MD/CD-R, CD, PHONO, VCR 2/DVR, VCR 1, D-TV/CBL, DVD ■ 8D COAXIAL IN for COAXIAL INPUT jack (5) Choices: (5) MD/CD-R, CD, PHONO, V-AUX, VCR 2/DVR, VCR 1, D-TV/CBL, DVD Notes • You cannot select an item more than once for the same type of jack. • When you connect a component to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. ≥ BLUE BACK………AUTO OSD SHIFT………………0 DIMMER………………………0 ■ BLUE BACK Select AUTO to display a blue background in the onscreen display when there’s no video signal input. Nothing is displayed on the screen, including the onscreen display, if OFF is selected. Choices: AUTO, OFF ■ OSD SHIFT (OSD off-set position) This setting is used to adjust the vertical position of the OSD. Control range: +5 (downward) to –5 (upward) Initial setting: 0 1 Press i to lower the position. Press j to raise the position. ■ DIMMER You can adjust the brightness of the front panel display. Control range: –4 to 0 Initial setting: 0 46 0108V730_41-47_EN(U) 46 12/27/01, 2:18 PM SET MENU 11 MEM. GUARD (memory guard) INTRODUCTION Use this feature to prevent accidental changes to settings on this unit. Choices: ON, OFF PREPARATION Select ON to protect the following features: • The on-screen display (OSD) mode • All SET MENU items • Center, rear speakers, rear center, and subwoofer levels • DSP program parameters Notes • When this item is set to ON, you cannot use the test tone. • When this item is set to ON, you cannot select any other SET MENU items. BASIC OPERATION ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 47 0108V730_41-47_EN(U) 47 12/27/01, 2:18 PM REMOTE CONTROL FEATURES In addition to controlling this unit, the remote control can operate other A/V components made by YAMAHA and other manufacturers. To control other components, you must set up the remote control with the manufacturer codes. Control area ■ Controlling this unit ■ Controlling other component The shaded areas below can be used to control this unit when the AMP mode is selected. Press AMP to select the AMP mode. The shaded areas below can be used to control other components. Each button has a different function depending on the selected components. Select the component to be controlled by pressing an input selector button or SELECT k/n. The name of the selected component appears in the display window. TRANSMIT RE–NAME CLEAR CODE SET SYSTEM POWER Å/ı/Ç buttons and input selector buttons STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD SELECT Press AMP to control this unit. POWER POWER TV AV AMP REC AUDIO DISC SKIP + The buttons in the dotted lines (SYSTEM POWER, STANDBY, SLEEP, 6CH INPUT, VOL +/–, MUTE and STEREO) function in any mode. Å/ı/Ç buttons and input selector buttons switch the control area for each component. * Å/ı/Ç buttons are to operate the other components that are not connected to this unit. Factory setting: Å...LD player ı...CD recorder Ç...TV TRANSMIT RE–NAME CLEAR CODE SET SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD VOL SELECT – LEVEL TITLE SET MENU + TV VOL A/B/C/D/E TV INPUT CH – MUTE MENU TV MUTE SELECT PRESET CH + PRESET TEST ON SCREEN TV VOL STEREO RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 EFFECT ENTERTAINMENT SELECT k/n switches control to another component without changing the input source on this unit. The display window will show one of the following: A, B, C, PHONO, V-AUX, TUNER, MDCDR, CD, TVCBL, VCR 1, VCR 2, DVD. AMP POWER POWER TV AV REC AUDIO DISC SKIP LEVEL 8 TITLE /DTS SUR. 9 10 11 12 0 +10 CHP/INDEX SET MENU + TV VOL TV INPUT EX/ES SELECT CH – MENU A/B/C/D/E TV MUTE SELECT PRESET CH + PRESET TEST ON SCREEN TV VOL RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 /DTS SUR. 9 6 ENTERTAINMENT 7 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX Component control area You can control up to 12 different components. You can set up manufacturer code and program other remote control functions for each component (see page 52). 48 0109V730_48-53_EN(U) 48 12/27/01, 2:18 PM REMOTE CONTROL FEATURES Setting the manufacturer code 3 The following table shows factory-set component (Library: component category) and the manufacturer code for each component control. Component control (buttons) Component category (Library) A LD YAMAHA B CD-R YAMAHA C TV – PHONO VCR – V-AUX VCR – + TV VOL Manufacturer CH – TV MUTE SELECT PRESET CH INTRODUCTION You can control other components by setting a manufacturer code. Codes can be set for each of the 12 component controls. Press u / d to select the name of your component’s manufacturer. You will find the names of most worldwide audiovideo manufacturers in alphabetical order in the display window. + PRESET TV VOL TUNER YAMAHA MD YAMAHA CD YAMAHA TV – VCR1 VCR – VCR2/DVR VCR – DVD DVD YAMAHA 4 SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL • If the manufacturer of your component has more than one code, try each of them until you find the correct one. Check to see if the selected code works in step 4. • If you wait for more than 30 seconds during step 3, the setup process is canceled. If this happens, start over from step 2. VCR 1 VCR2/DVR Press one of the buttons shaded below to see if you can control your component. If so, the manufacturer code is correct. DVD POWER POWER TV AV AMP REC AUDIO DISC SKIP + ADDITIONAL INFORMATION VOL 2 ADVANCED OPERATION Press an input selector button or Å/ı/Ç to select the component you want to set up. Notes BASIC OPERATION CD D-TV/CBL If you want to change a library (component category), press j / i. You can set a different component from the input selector name. Library choices: DVD, LD, CD, CD-R, MD, TAPE, TUNER, TV, CABLE, DBS, SAT, VCR PREPARATION 1 TUNER MD/CD-R – Press CODE SET using a ballpoint pen or similar object. “SETUP” and the selected component name appear alternately in the display window. – LEVEL TITLE TV INPUT SET MENU + TV VOL MUTE MENU A/B/C/D/E y • If you want to continue setting up codes for other components, press TV MUTE/SELECT and repeat steps 1, 3 and 4. 5 Press CODE SET again to exit from the setup mode. CODE SET APPENDIX CODE SET Note English • “ERROR” appears in the display window when pressing buttons other than those indicated in each step, or when pressing more than one button at once. 49 0109V730_48-53_EN(U) 49 12/27/01, 2:18 PM REMOTE CONTROL FEATURES Changing the source name in the display window You can change the name that appears in the display window on the remote control if you want to use a different name than the original. This is useful when you have set the input selector buttons to control different components. 1 Press an input selector button or Å/ı/Ç to select the source component you want to rename. The selected component name appears in the display window. SYSTEM 2 3 POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD Press RE-NAME by using a ballpoint pen or similar object. RE-NAME Press u / d to select and enter a character. Pressing d changes the character in the following order: A to Z, a to z, 0 to 9, space, - (hyphen) and / (slash). (Pressing u goes in the reverse order.) + TV VOL CH – TV MUTE SELECT PRESET CH + PRESET TV VOL – 4 Press j / i to move the cursor to the next position. Repeat step 3 and 4 until the new name is completed. + TV VOL CH TV MUTE SELECT – PRESET CH + PRESET TV VOL – y • If you want to continue setting up codes for other components, press TV MUTE/SELECT and repeat steps 1, 3 and 4. 5 Press RE-NAME again to exit from the renaming mode. RE-NAME 50 0109V730_48-53_EN(U) 50 12/27/01, 2:18 PM REMOTE CONTROL FEATURES Clearing renamed source names, and setup manufacturer codes Press an input selector button or Å/ı/Ç to select the component control for which you want to clear the name, function or manufacturer code. Press and hold CLEAR again for about 3 seconds. “C:OK” appears in the display window. INTRODUCTION 1 4 CLEAR SYSTEM STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD Press CLEAR by using a ballpoint pen or similar object. Note • “C:NG” appears in the display window if the operation is unsuccessful. In this case, start over from step 2. 5 Press CLEAR to exit from the clearing mode. CLEAR Note CLEAR Note BASIC OPERATION • “ERROR” appears in the display window when pressing buttons other than indicated in each step, or more than one button at once. • If you do not press any button within 30 seconds after step 2, the clearing process is canceled. If this happens, start over from step 1. 3 Press u / d to select the clear mode. The mode is shown in the display window in the following order: ADVANCED OPERATION + TV VOL CH – TV MUTE SELECT PRESET PREPARATION 2 POWER CH + PRESET TV VOL – ADDITIONAL INFORMATION (L: name of a component) Clears setup manufacturer code for the component control. Clears all renamed source names in the display window. APPENDIX Clears all setup manufacturer codes and renamed source names. This returns to the factory settings. English 51 0109V730_48-53_EN(U) 51 12/27/01, 2:18 PM REMOTE CONTROL FEATURES Controlling other components You can operate other components when you have set the manufacturer code for your component. Note, however, that some buttons may not operate your component. Once you select an input source, the remote control switches to the mode for operating the component. You can also select a component to operate other than the one selected as the input source by pressing SELECT k/n. The display window shows the currently selected component that you can operate. SELECT 1 POWER POWER TV AV AMP 9 0 REC 2 3 AUDIO + DISC SKIP VOL – 4 q LEVEL 5 MENU TV VOL w A/B/C/D/E TV INPUT 6 MUTE SET MENU + TITLE CH CH TV MUTE SELECT – + PRESET TEST STEREO ON SCREEN TV VOL 7 e PRESET RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT EFFECT 8 1 2 3 4 TV SPORTS MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 6 7 5 /DTS SUR. 1 TV POWER 2 REC/DISC SKIP 3w VCR *2TV power *2TV power TV power Disc skip Rec *3VCR rec Play Play *3VCR play y Skip forward t Skip backward 8 EX/ES SELECT 9 DVD player ENTERTAINMENT 10 11 12 0 +10 CHP/INDEX TV, digital/cable TV LD player CD player CD/MD recorder Tuner *2TV power *2TV power *2TV power *2TV power Disc skip Rec (MD) Play Play Play Skip forward Skip forward Skip forward Skip backward Skip backward Skip backward d Pause Pause *3VCR pause Pause Pause Pause a Stop Stop *3VCR stop Stop Stop Stop 4e Search backward Search backward Search backward 5 TITLE/TV INPUT 6 TV VOL +/ u Search backward *3VCR search backward Search backward *2TV input Title 2 Up * TV volume up *2TV input TV input TV volume up 2 * TV volume up *2TV input 2 * TV volume up *2TV input 2 * TV volume up TV VOL –/ d Down *2TV volume down TV volume down *2TV volume down *2TV volume down *2TV volume down CH +/ i Right VCR channel up CH –/ j Left VCR channel down TV channel down *2TV channel down *2TV channel down *2TV channel down TV MUTE/SELECT 7 RETURN 8 1-11 9 AV POWER 0 AUDIO qr w MENU/A/B/C/D/E e DISPLAY r 12/CHP/INDEX r TV channel up *2TV channel up *2TV channel up *2TV channel up Preset up Preset down *2TV mute TV mute *2TV mute *2TV mute *2TV mute Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Preset stations (1-8) *1Power *1Power *3VCR power *1Power *1Power *1Power *1Power Search forward Search forward Display Display Display Chapter/Time Index Index Select Return Audio Sound Search forward Search forward *3VCR search forward Search forward Menu A/B/C/D/E Display Title/Index Enter Enter 1 * This button functions only when the original remote control of the component has POWER button. *2 These buttons can operate your TV without switching the input if the manufacturer code is set in D-TV/CBL or Ç. When the manufacturer code for your TV is set up in the both D-TV/CBL and Ç areas, priority is given to the signal in the D-TV/CBL area. *3 These buttons can operate your VCR without switching the input to VCR 1 if the manufacturer code is set in VCR 1. 52 0109V730_48-53_EN(U) 52 12/27/01, 2:18 PM ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS Adjustment should be made with the remote control. TRANSMIT RE–NAME CLEAR 3 Press j / i to adjust the speaker output level. • The control range for the center or rear left and right speakers is from +10 dB to –10 dB. • The control range for the subwoofer is from 0 dB to –20 dB. CODE SET + SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO V-AUX TUNER MD/CD-R CD TV VOL REC AUDIO + DISC SKIP CH – VOL VCR 1 VCR2/DVR DVD SELECT POWER POWER TV AV AMP TITLE AUD O CH CH – TV MUTE SELECT Notes + PRESET ON SCREEN RETURN – DISPLAY HALL JAZZ CLUB ROCK CONCERT EFFECT ENTERTAINMENT 1 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 9 Press AMP. 8 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX AMP (While playing a source) 2 LEVEL TITLE ADVANCED OPERATION Press LEVEL repeatedly to select the speaker(s) you want to adjust. Each time you press LEVEL, the selected speaker changes and appears on the front panel display as follows: center, rear right, rear center, rear left and subwoofer. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, if the power cord is disconnected from the AC outlet, or the power supply is cut for more than one week, the stored data will be lost. If so, set the output level again. BASIC OPERATION • When the speaker output modes for “1A CENTER” and “1C REAR LR” are set to NON, and “1E BASS” to MAIN, the output level of those speakers cannot be adjusted because there is no sound coming from these speakers. • When you adjust the output level with LEVEL, the settings you made with the test tone will be changed. • We recommend adjusting the speakers by following the steps described in “Using the test tone” on pages 22 and 23. STEREO TV SPORTS /DTS SUR. 1 MENU A/B/C/D/E PRESET 3 + PRESET – MUTE SET MENU + TV VOL TV VOL 1 CH TV VOL LEVEL TV INPUT TEST REC PRESET – 2 2 TV MUTE SELECT PREPARATION D-TV/CBL INTRODUCTION You can adjust the output level of each effect speaker (center, rear left and right, rear center and subwoofer) while listening to a source. TV INPUT ADDITIONAL INFORMATION Center speaker output level Rear right speaker output level Rear center speaker output level APPENDIX Rear left speaker output level Subwoofer output level y English • Once you press LEVEL, you can also select the speaker(s) to be adjusted by pressing d / u. + TV VOL LEVEL TITLE CH TV INPUT PRESET – TV MUTE SELECT CH + PRESET TV VOL – 53 0109V730_48-53_EN(U) 53 12/27/01, 2:18 PM SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field? What really creates the rich, full tones of a live instrument are the multiple reflections from the walls of the room. In addition to making the sound “live”, these reflections enable us to tell where the player is situated, and the size and shape of the room in which we are sitting. ■ Elements of a sound field In any environment, in addition to the direct sound coming straight to our ears from the player’s instrument, there are two distinct types of sound reflections that combine to make up the sound field: Early reflections Reflected sounds reach our ears extremely rapidly (50 ms – 100 ms after the direct sound), after reflecting from one surface only — for example, from the ceiling or a wall. These reflections fall into specific patterns for any particular environment, and provide vital information to our ears. Early reflections actually add clarity to the direct sound. Reverberations These are caused by reflections from more than one surface — walls, ceiling, the back of the room — so numerous that they merge together to form a continuous sonic “afterglow”. They are non-directional, and lessen the clarity of the direct sound. Direct sound, early reflections and subsequent reverberation taken together help us to determine the subjective size and shape of the room, and it is this information that the digital sound field processor reproduces in order to create sound fields. If you could create the appropriate early reflections and subsequent reverberations in your listening room, you would be able to create your own listening environment. The acoustics in your room could be changed to those of a concert hall, a dance floor, or virtually any size room at all. This ability to create sound fields at will is exactly what YAMAHA has done with the digital sound field processor. Sound field program parameters DSP programs consist of some parameters to determine the apparent room size, reverberation time, distance from you to the performer, etc. In each program, these parameters are set with values precisely calculated by YAMAHA to create a sound field unique to the program. It is recommended to use DSP programs without changing the values of parameters. However, this unit also allows you to create your own sound field by starting with one of the built-in program and adjusting its parameters. Each DSP program has a set of parameters that allow you to change the characteristics of the acoustic environment to create the precise effect you want. These parameters correspond to the many natural acoustic factors that create the sound field you experience in an actual concert hall or other listening environment. The size of the room, for example, affects the length of time between the early reflections. The “ROOM SIZE” parameter provided in many of the DSP programs alters the timing between these reflections, thus changing the shape of the “room” you are listening. In addition to room size, the shape of the room and the characteristics of its surfaces have a significant effect on the final sound. Surfaces that absorb sound, for example, cause the reflections and reverberations to die out more quickly, while highly reflective surfaces allow the reflections to carry on for a longer period of time. The digital sound field parameters allow you to control these and many other factors that contribute to your personal sound field, allowing you to essentially “redesign” the concert halls, theaters, etc. provided to create custom-tailored listening environments that ideally match your mood and music. 54 0110V730_54-59_EN(U) 54 12/27/01, 2:18 PM SOUND FIELD PROGRAM PARAMETER EDITING 4 Changing parameter settings Press u / d to select the parameter. CH – TV MUTE SELECT PRESET CH + INTRODUCTION You can enjoy high quality sound with the factory-set parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room. + TV VOL PRESET TV VOL – 5 Adjustments should be made with the remote control. Press j / i to change the parameter value. + TV VOL y CH – • It is recommended to use on-screen display when changing the settings. TV MUTE SELECT PRESET CH + PRESET TV VOL – RE–NAME CLEAR y CODE SET SYSTEM POWER STANDBY SLEEP 6CH INPUT A B C PHONO TV AUDIO V-AUX TUNER MD/CD-R CD D-TV/CBL VCR 1 VCR2/DVR DVD • When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name on the video monitor. To reset to the factory-set value, press j / i repeatedly until the asterisk mark disappears. AV REC + DISC SKIP VOL – LEVEL SET MENU + TITLE SELECT TV VOL TV INPUT A/B/C/D/E CH POWER POWER TV AV TV MUTE SELECT – AMP PRESET RETURN – HALL JAZZ CLUB STEREO DISPLAY 4 2 3 4 MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 Press AMP. 2 Turn on the video monitor and press ON SCREEN repeatedly to select the full display mode. 8 3 EX/ES SELECT 10 11 12 0 +10 CHP/INDEX AMP ON SCREEN DISPLAY Select a DSP program you want to adjust. ROCK CONCERT ENTERTAINMENT 2 3 4 MONO MOVIE MOVIE THEATER 1 MOVIE THEATER 2 5 6 7 /DTS SUR. 9 Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again. ADDITIONAL INFORMATION 1 TV SPORTS Notes • For some of the programs, the available parameters may be displayed on more than one OSD page. To scroll through pages, press u / d. • You cannot change parameter values when “11 MEM. GUARD” on the SET MENU is set to ON. ADVANCED OPERATION 1 JAZZ CLUB Repeat steps 3 to 5 above as necessary to change other program parameters. BASIC OPERATION ENTERTAINMENT 2 MONO MOVIE 9 HALL 6 EFFECT ROCK CONCERT 1 TV SPORTS /DTS SUR. 3 + ON SCREEN TV VOL 5 1 CH PRESET TEST REC MUTE MENU 8 MATRIX 6.1 SELECT 10 11 12 0 +10 CHP/ NDEX Program No. PREPARATION TRANSMIT Program name P03 ROCK CONCERT ≥ INIT.DLY…………15ms ROOM SIZE…………1.0 LIVENESS…………………5 REV.TIME…………1.6s REV.DELAY……120ms REV.LEVEL……………7% Parameters APPENDIX Cursor Parameter values English Example of the parameter setting display 55 0110V730_54-59_EN(U) 55 12/27/01, 2:18 PM DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your listening room. Not all of the following parameters are found in every program. ■ INIT. DLY (Initial delay) [P. INT. DLY for the presence sound field] Function: This parameter changes the apparent distance from the source sound by adjusting the delay between the direct sound and the first reflection heard by the listener. Description: The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther the apparent distance seems. For a small room, this parameter would be set to a small value, and for a large room, it would be set to a large value. Control Range: 1 to 99 msec Sound source Level Level Level Early reflections Time Time INIT.DLY Time INIT.DLY INIT.DLY Sound source Reflection face 1 ms 99 ms ■ ROOM SIZE [P. ROOM SIZE for the presence sound field] Function: This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the surround sound field becomes. Description: As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between the original reflected sound and the subsequent reflections. By controlling the time between the reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from one to two, doubles the apparent length of the room. Control Range: 0.1 to 2.0 Time Early reflections Level Level Level Sound source Time Time Sound source 0.1 2.0 56 0110V730_54-59_EN(U) 56 12/27/01, 2:18 PM DIGITAL SOUND SOUND FIELD FIELD PROGRAM PARAMETER PARAMETER DESCRIPTIONS EDITING ■ LIVENESS Function: Sound source INTRODUCTION This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the early reflections decay. Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces is referred to as “dead”, while a room with highly reflective surfaces is referred to as “live”. The LIVENESS parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the room. Control range: 0 to 10 Live Level Level Level Time PREPARATION Dead Time Time Sound source 0 Large reflected sound BASIC OPERATION Small reflected sound 10 ■ S. DELAY (Surround delay) Function: This parameter adjusts the delay between the direct sound and the surround sound. (Control range varies depending on programs.) Control range: varies depending on the signal format. Function: This parameter adjusts the delay between the direct sound and the first reflection on the surround side of the sound field. You can only adjust this parameter when at least two front channels and two rear channels are used. Control range: 1 to 49 msec ADVANCED OPERATION ■ S. INIT. DLY (Surround initial delay) ■ S. ROOM SIZE (Surround room size) ADDITIONAL INFORMATION Function: This parameter adjusts the apparent size of the surround sound field. Control range: 0.1 to 2.0 ■ S. LIVENESS (Surround liveness) Function: This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field. Control range: 0 to 10 ■ RC. INIT. DLY (Rear center initial delay) Function: APPENDIX This parameter adjusts the delay between the direct sound and the first reflection in the rear center sound field. Control range: 1 to 49 msec ■ RC. ROOM SIZE (Rear center room size) Function: This parameter adjusts the apparent size of the rear center sound field. Control range: 0.1 to 2.0 ■ RC. LIVENESS (Rear center liveness) English Function: This parameter adjusts the apparent reflectivity of the virtual wall in the rear center sound field. Control range: 0 to 10 57 0110V730_54-59_EN(U) 57 12/27/01, 2:18 PM DIGITAL SOUND FIELD PARAMETER DESCRIPTIONS ■ REV. TIME (Reverberation time) Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an extremely wide range. Description: Set a longer reverberation time for “dead” sources and listening room environments, and a shorter time for “live” sources and listening room environments. Control range: 1.0 to 5.0 sec Reverberation Sound source Reverberation Early reflections 60 dB REV. TIME 60 dB REV. TIME REV. TIME Long reverberation Short reverberation Sound source 60 dB 1.0 s 5.0 s ■ REV. DELAY (Reverberation delay) This parameter adjusts the time difference between the beginning of the direct sound and the beginning of the reverberation sound. Description: The larger the value, the later the reverberation sound begins. A later reverberation sound makes you feel like you are in a larger acoustic environment. Control range: 0 to 250 msec Level Function: Sound source (dB) 60 dB Reverberation Time REV. DELAY REV. TIME ■ REV. LEVEL (Reverberation level) Level Function: This parameter adjusts the volume of the reverberation sound. Description: The larger the value, the stronger the reverberation becomes. Control range: 0 to 100% Sound source REV. LEVEL Time 58 0110V730_54-59_EN(U) 58 12/27/01, 2:18 PM DIGITAL SOUND SOUND FIELD FIELD PROGRAM PARAMETER PARAMETER DESCRIPTIONS EDITING For 6ch Stereo Function: These parameters adjust the volume level for each channel in 6-channel stereo mode. Control range: 0 to 100% INTRODUCTION ■ CT LEVEL (Center level) ■ RL LEVEL (Rear left level) ■ RR LEVEL (Rear right level) ■ RC LEVEL (Rear center level) PREPARATION For PRO LOGIC Music ■ PANORAMA Function: Choices: Extends the front stereo image to include the surround speakers for wraparound effect. OFF/ON, initial setting is OFF. ■ DIMENSION ■ CT WIDTH (Center width) Function: Adjusts the center image from all three front speakers to varying degrees. The larger the value, adjusts the center image towards the main left and right speakers. Control range: 0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only from main left and right speakers), initial setting is 3. BASIC OPERATION Function: Gradually adjusts the soundfield either towards the front or towards the rear. Control range: –3 (towards the rear) to +3 (towards the front), initial setting is STD (standard). ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 59 0110V730_54-59_EN(U) 59 12/27/01, 2:18 PM TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to turn on when STANDBY/ ON (or SYSTEM POWER) is pressed, or enters in the standby mode soon after the power has been turned on. On-screen display does not appear. No sound. The picture does not appear. Cause Remedy The power cord is not connected or the plug is not completely inserted. Firmly connect the power cord. — The IMPEDANCE SELECTOR switch on the rear panel is not fully set to either the left or right position. Set the switch fully to the left or right position when this unit is in the standby mode. 12 The protection circuitry has been activated. Make sure all speaker wire connections on this unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection. 10, 11 This unit has been exposed to a strong external electric shock (such as lightning and strong static electricity). Set this unit in the standby mode, disconnect the power cord, plug it back in after 30 seconds, then start operating. — The setting for the on-screen display is set to “DISPLAY OFF”. Select the full display or short display mode. 20 The BLUE BACK setting under “10 DISPLAY SET” on the SET MENU is set to OFF, and no video signal is input to this unit. Set BLUE BACK to AUTO to always show the OSD. 46 Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 10 – 16 An appropriate input source has not been selected. Select an appropriate input source with INPUT l / h or 6CH INPUT (or the input selector buttons). 24 The speaker connections are not secure. Secure the connections. The main speakers to be used have not been selected properly. Select the main speakers with SPEAKERS A and/or B. 24 The volume is turned down. Turn up the volume. 25 The sound is muted. Press MUTE or any operation buttons of this unit to cancel a mute and adjust the volume. — Digital signals which this unit cannot reproduce are being input to this unit by playing a CD-ROM, etc. Play a source whose signals this unit can reproduce. — The output and input for the picture are connected to different types of video jacks. Make connections using the same type of video jacks (S VIDEO, VIDEO (composite), or COMPONENT VIDEO) for both the input and output. 60 0111V730_60-67_EN(U) Refer to page 60 12/27/01, 2:18 PM 10, 11 14, 15 TROUBLESHOOTING Problem Cause The sound suddenly goes off. The protection circuit has been activated because of a short circuit, etc. Check the IMPEDANCE SELECTOR switch is set to the appropriate position and then turn this unit back on. 12 Check the speaker wires are not touching each other and then turn this unit back on. — The sleep timer has functioned. Turn on the power, and play the source again. — The sound is muted. Press MUTE or any operation buttons of this unit to cancel a mute and adjust the volume. — Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 10, 11 Incorrect setting of “5 L/R BALANCE” on the SET MENU. Adjust it to the appropriate position. 45 The sound effect is off. Press STEREO/EFFECT to turn it on. 29 A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS. Select another DSP program. No sound from the center speaker. — Raise the level of the center speaker. 52 “1A CENTER” on the SET MENU is set to NON. Select the appropriate mode for your center speaker. 42 One of the Hi-Fi DSP programs (1 to 4) has been selected (except for 6ch Stereo). Select another DSP program. — The output level of the rear speakers is set to minimum. Raise the output level of the rear speakers. A monaural source is being played with program 9. Select another DSP program. “1E BASS” on the SET MENU is set to MAIN when a Dolby Digital or DTS signal is being played. Select SWFR or BOTH. 43 “1E BASS” on the SET MENU is set to SWFR or MAIN when a 2-channel source is being played. Select BOTH. 43 Poor bass reproduction. 27 – 34 APPENDIX The source does not contain low bass signals (90 Hz and below). 52 — Select MAIN. 43 The speaker mode settings (main, center, rear, or rear center) on the SET MENU does not match your speaker configuration. Select the appropriate position for each speaker based on the size of the speakers in your configuration. 42 – 44 61 0111V730_60-67_EN(U) 61 12/27/01, 2:18 PM English “1E BASS” on the SET MENU is set to SWFR or BOTH and your system does not include a subwoofer. ADDITIONAL INFORMATION No sound from the subwoofer. 27 – 34 ADVANCED OPERATION The output level of the center speaker is set to minimum. The source encoded with a Dolby Digital or DTS signal does not have a center channel signal. No sound from the rear speakers. 27 – 34 BASIC OPERAIONT A 96-kHz sampling digital signal is being input to this unit. PREPARATION No sound from the effect speakers. Refer to page INTRODUCTION Only the speaker on one side can be heard. Remedy TROUBLESHOOTING Problem Cause No sound from the rear center speaker. Remedy Refer to page “1C REAR LR” or “1D REAR CT” on the SET MENU is set to NON. Select LRG or SML. 43 The Dolby Digital EX decoder or the DTS-ES compatible decoder is not on. Press the EX/ES button on the remote control to turn it on. 29 Incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective. 10 – 16 No connection from the turntable to the GND terminal. Connect the grounding cord of your turntable to the GND terminal of this unit. — The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The turntable should be connected to this unit through an MC-head amplifier. — The volume level cannot be increased, or the sound is distorted. The component connected to the OUT (REC) jacks of this unit is turned off. Turn on the power to the component. — The sound effect cannot be recorded. It is not possible to record the sound effect by a recording component. A source cannot be recorded by a digital recording component connected to the DIGITAL OUTPUT jack of this unit. A source component is not connected to the DIGITAL INPUT jacks of this unit. Connect the source component to the DIGITAL INPUT jacks of this unit. — The sound field parameters and some other settings on this unit cannot be changed. “11 MEM. GUARD” in the SET MENU is set to ON. Set “11 MEM. GUARD” in the SET MENU to OFF. — This unit does not operate properly. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Disconnect the AC power cord from the outlet and then plug it in again after about 30 seconds. — “CHECK SP WIRES” appears on the front panel display. Speaker cables are short circuited. Make sure all speaker cables are connected correctly. — There is noise interference from digital or high-frequency equipment, or this unit. This unit is too close to the digital or high-frequency equipment. Move this unit further away from such equipment. — This unit suddenly turns into the standby mode. The internal temperature becomes too high and the overheat protection circuitry has been activated. Wait until this unit cools down and then turn it back on. — A “humming” sound can be heard. — 62 0111V730_60-67_EN(U) 62 12/27/01, 2:18 PM TROUBLESHOOTING ■ Tuner Problem Cause 17 Use the manual tuning method. 35 There is distortion, and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust the antenna position to eliminate multipath interference. — The desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use a high-quality directional FM antenna. 17 Use the manual tuning method. 35 Previously preset stations can no longer be tuned in. This unit has been disconnected for a long period. Re-store the stations. The desired station cannot be tuned in with the automatic tuning method. The signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception. 17 Use the manual tuning method. 35 There are continuous crackling and hissing noises. Noises result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. 17 There are buzzing and whining noises (especially in the evening). A TV set is being used nearby. Move this unit away from the TV. — 36, 37 BASIC OPERAIONT AM Check the antenna connections. Try using a high-quality directional FM antenna. PREPARATION FM The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Refer to page INTRODUCTION FM stereo reception is noisy. Remedy ADVANCED OPERATION ■ Remote control The remote control does not work nor function properly. Cause Remedy Refer to page The remote control will function within a maximum range of 6 m (20 feet) and no more than 30 degrees off-axis from the front panel. 7 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit. — The batteries are weak. Replace all batteries with new ones. 3 The manufacture code has not correctly set. Set the code correctly. 49 Try setting another code of the same manufacturer. — — English Even if the manufacturer code is correctly set, there are some models that do not respond to the remote control. APPENDIX Wrong distance or angle. 63 0111V730_60-67_EN(U) 63 12/27/01, 2:19 PM ADDITIONAL INFORMATION Problem GLOSSARY ■ Dolby Surround Dolby Surround uses a 4 channel analog recording system to reproduce realistic and dynamic sound effects: 2 main left and right channels (stereo), a center channel for dialog (monaural), and a rear channel for special sound effects (monaural). The rear channel reproduces sound within a narrow frequency range. Dolby Surround is widely used with nearly all video tapes and laser discs, and in many TV and cable broadcasts as well. The Dolby Pro Logic decoder built into this unit employs a digital signal processing system that automatically stabilizes the volume on each channel to enhance moving sound effects and directionality. ■ Dolby Digital Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (left, center, and right), and 2 rear stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE (low frequency effect), the system has a total of 5.1 channels (LFE is counted as 0.1 channel). By using 2-channel stereo for the rear speakers, more accurate moving sound effects and surround sound environment are possible than with Dolby Surround. The wide dynamic range (from maximum to minimum volume) reproduced by the 5 full-range channels and the precise sound orientation generated using digital sound processing provide listeners with previously unheard of excitement and realism. With this unit, any sound environment from monaural up to a 5.1-channel configuration can be freely selected for your enjoyment. Dolby Digital EX creates 6 full-bandwidth output channels from 5.1-channel sources. This is done using a matrix decoder that derives 3 surround channels from the 2 in the original recording. For the best results, Dolby Digital EX should be used with movie sound tracks recorded with Dolby Digital Surround EX. With this additional channel, you can experience more dynamic and realistic moving sound especially with scenes with “flyover” and “fly-around” effects. ■ Dolby Pro Logic Dolby Pro Logic is an improved technique used to decode vast numbers of existing Dolby Surround softwares. This new technology enables a discrete 5channel playback with 2 main left and right channels, 1 center channel, and 2 rear left and right channels (instead of only 1 rear channel for conventional Pro Logic technology). A music mode is also available for 2-channel sources in addition to the movie mode. ■ DTS (Digital Theater Systems) Digital Surround DTS digital surround was developed to replace the analog soundtracks of movies with a 6-channel digital sound track, and is now rapidly gaining popularity in movie theaters around the world. Digital Theater Systems Inc. has developed a home theater system so that you can enjoy the depth of sound and natural spatial representation of DTS digital surround in your home. This system produces practically distortion-free 6-channel sound (technically, a left, right and center channels, 2 rear channels, plus an LFE 0.1 channel as a subwoofer, for a total of 5.1 channels). The unit incorporates DTS-ES compatible decoder that enables 6.1-channel reproduction by adding the rear center channel to existing 5.1-channel format. (The rear center channel is created from rear left and right channels.) ■ LFE 0.1 channel This channel is for the reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low frequency range compared to the full-range reproduced by the other 5 channels in a Dolby Digital or DTS 5.1 channel systems. ■ CINEMA DSP ■ SILENT CINEMA YAMAHA has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed using headphones. 64 0111V730_60-67_EN(U) 64 D I G I T A L Since the Dolby Surround and DTS systems were originally designed for use in movie theaters, their effect is best felt in a theater having many speakers and designed for acoustic effects. Since home conditions, such as room size, wall material, number of speakers, and so on, can differ so widely, it’s inevitable that there are differences in the sound heard as well. Based on a wealth of actually measured data, YAMAHA CINEMA DSP uses YAMAHA original sound field technology to combine Dolby Pro Logic, Dolby Digital and DTS systems to provide the visual and audio experience of movie theater in the listening room of your own home. 12/27/01, 2:19 PM GLOSSARY YAMAHA has developed a virtual CINEMA DSP algorithm that allows you to enjoy DSP sound field surround effects even without any rear speakers by using virtual rear speakers. It is even possible to enjoy virtual CINEMA DSP using a minimal 2-speaker system that does not include a center speaker. With the S-video signal system, the video signal normally transmitted using a pin cable is separated and transmitted as the Y signal for the luminance and the C signal for the chrominance through the S-video cable. Using the S VIDEO jack eliminates video signal transmission loss and allows recording and playback of even more beautiful images. ■ PCM (Linear PCM) ■ Component video signal Linear PCM is a signal format under which an analog audio signal is digitized, recorded and transmitted without using any compression. This is used as a method of recording CDs and DVD audio. The PCM system uses a technique for sampling the size of the analog signal per very small unit of time. Standing for “pulse code modulation”, the analog signal is encoded as pulses and then modulated for recording. With the component video signal system, the video signal is separated into the Y signal for the luminance and the PB/CB and PR/CR signals for the chrominance. Color can be reproduced more faithfully with this system because each of these signals is independent. The component signal is also called the “color difference signal” because the luminance signal is subtracted from the color signal. A monitor with component input jacks is required in order to use the component signal for output. ■ Sampling frequency and number of quantized bits PREPARATION ■ S-video signal INTRODUCTION ■ Virtual CINEMA DSP BASIC OPERAIONT ADVANCED OPERATION When digitizing an analog audio signal, the number of times the signal is sampled per second is called the sampling frequency, while the degree of fineness when converting the sound level into a numeric value is called the number of quantized bits. The range of rates that can be played back is determined based on the sampling rate, while the dynamic range representing the sound level difference is determined by the number of quantized bits. In principle, the higher the sampling frequency, the wider the range of frequencies that can be played back, and the higher the number of quantized bits, the more finely the sound level can be reproduced. ADDITIONAL INFORMATION APPENDIX English 65 0111V730_60-67_EN(U) 65 12/27/01, 2:19 PM SPECIFICATIONS AUDIO SECTION FM SECTION • Minimum RMS Output Power for Main, Center, Rear, Rear Center 20 Hz to 20 kHz, 0.06% THD, 8 Ω ....................................... 75 W 1 kHz, 0.06% THD, 8 Ω ........................................................ 80 W • Tuning Range [U.S.A. and Canada models] ............................ 87.5 to 107.9 MHz [Other models] .............................................. 87.50 to 108.00 MHz • DIN Standard Output Power [Europe model] 1 kHz, 0.7% THD, 4 Ω ........................................................ 125 W • 50 dB Quieting Sensitivity (IHF, 100% mod.) Mono/Stereo ........................ 2.0 µV (17.3 dBf) /25 µV (39.2 dBf) • Maximum Power (EIAJ) [China, Korea and General models] 1 kHz, 10% THD, 8 Ω ......................................................... 110 W • Dynamic Power (IHF) 8/6/4/2 Ω .......................................................... 90/120/150/190 W • Damping Factor 20 Hz to 20 kHz, 8 Ω ................................................... 80 or more • Selectivity (400 kHz) ............................................................... 70 dB • Signal to Noise Ratio (IHF) Mono/Stereo .............................................................. 76 dB/70 dB • Harmonic Distortion (1 kHz) Mono/Stereo ................................................................. 0.2%/0.3% • Stereo Separation (1 kHz) ....................................................... 45 dB • Frequency Response ........................... 20 Hz to 15 kHz +0.5, –2 dB • Frequency Response CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB AM SECTION • Total Harmonic Distortion 20 Hz to 20 kHz, 50 W, 8 Ω, Main L/R ................................ 0.06% • Usable Sensitivity ............................................................. 300 µV/m • Signal to Noise Ratio (IHF-A Network) PHONO MM to OUT (REC) (5 mV, shorted) [U.S.A., Canada, China, Korea and General models] ....... 86 dB [Other models] ................................................................... 81 dB CD (250 mV, shorted) to Main L/R, Effect Off ................. 100 dB • Residual Noise (IHF-A Network) Main L/R ................................................................ 150 µV or less • Channel Separation (1 kHz/10 kHz) CD (5.1 kΩ terminated) to Main L/R ........................ 60 dB/45 dB • Tone Control (Main L/R) BASS Boost/Cut ...................................................... ±10 dB/50 Hz TREBLE Boost/Cut ............................................... ±10 dB/20 kHz • Phones Output ............................................................. 0.34 V/560 Ω • Input Sensitivity CD, etc .................................................................... 150 mV/47 kΩ 6CH INPUT ............................................................ 150 mV/47 kΩ • Output Level OUT (REC) ........................................................... 150 mV/1.2 kΩ OUTPUT MAIN/CENTER/REAR CENTER/ REAR (SURROUND) ............................................ 2.2 V/1.2 kΩ OUTPUT SUBWOOFER ............................................. 4 V/1.2 kΩ VIDEO SECTION • Video Signal Type ...................................................... NTSC or PAL • Composite Video Signal Level ...................................... 1 Vp-p/75 Ω • Tuning Range ......................................... 530/531 to 1710/1611 kHz GENERAL • Power Supply [U.S.A. and Canada models] ............................... AC 120 V/60 Hz [Australia model] ................................................. AC 240 V/50 Hz [U.K., Europe and Singapore models] ................ AC 230 V/50 Hz [Korea model] ..................................................... AC 220 V/60 Hz [China and General models] ..... AC 110/120/220/240 V, 50/60 Hz • Power Consumption [U.S.A. and Canada models] .................................. 290 W/370 VA [Other models] ..................................................................... 290 W Standby Mode ......................................................... approx. 0.6 W • AC Outlets [U.S.A., Canada, Europe and Singapore models] .......................................................... 2 (Total 100 W maximum) [China and General models] .................. 2 (Total 50 W maximum) [U.K. and Australia models] ......................... 1 (100 W maximum) • Dimension (W x H x D) .......................... 435 x 161 x 390 mm (17” x 6-7/16” x 15-3/8”) • Weight ...................................................................... 11.5 kg (25 lbs) • Accessories ............................................................... Remote control Batteries Front VIDEO AUX jack cap 75-ohm/300-ohm antenna adapter (U.K. model) AM loop antenna Indoor FM antenna *Specifications are subject to change without notice. • S-Video Signal Level Y ................................................................................. 1 Vp-p/75 Ω C .......................................................................... 0.286 Vp-p/75 Ω • Component Video Signal Level Y ................................................................................. 1 Vp-p/75 Ω PB/CB, PR/CR ............................................................. 0.7 Vp-p/75 Ω • Signal to Noise Ratio ............................................................... 50 dB • Frequency Response (MONITOR OUT) Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB Component ................................................. DC to 30 MHz, –3 dB 66 0111V730_60-67_EN(U) 66 1/9/02, 6:18 PM YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 0112V730(U)-cv4 1 Printed in Malaysia 12/27/01, 2:19 PM V874750