Pioneer FH-460UI Manual de usuario

Categoría
Receptores de medios de coche
Tipo
Manual de usuario
Black plate (1,1)
Owners Manual
Mode demploi
Manuale distruzioni
Manual de instrucciones
Bedienungsanleitung
Handleiding
Руководство пользователя
CD RDS RECEIVER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
FH-460UI
English NederlandsDeutschEspañolItalianoFrançais Русский
Black plate (2,1)
Thank you for purchasing this PIONEER
product
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARN-
INGs and CAUTIONs in this manual. Please
keep the manual in a safe and accessible place for
future reference.
If you want to dispose this product, do not
mix it with general household waste. There is
a separate collection system for used elec-
tronic products in accordance with legislation
that requires proper treatment, recovery and
recycling.
Private households in the member states of the
EU, in Switzerland and Norway may return their
used electronic products free of charge to desig-
nated collection facilities or to a retailer (if you
purchase a similar new one).
For countries not mentioned above, please con-
tact your local authorities for the correct method
of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment, re-
covery and recycling and thus prevent potential
negative effects on the environment and human
health.
About this unit
The tuner frequencies on this unit are allocated
for use in Western Europe, Asia, the Middle
East, Africa and Oceania. Use in other areas
may result in poor reception. The RDS (radio
data system) function only works in areas that
broadcast RDS signals for FM stations.
WARNING
! Do not attempt to install or service this
product by yourself. Installation or serv-
icing of this product by persons without
training and experience in electronic
equipment and automotive accessories
may be dangerous and could expose you
to the risk of electric shock, injury or
other hazards.
! Do not attempt to operate the unit while driv-
ing. Make sure to pull off the road and park
your vehicle in a safe location before at-
tempting to use the controls on the device.
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with
liquids.
! The Pioneer CarStereo-Pass is for use only in
Germany.
! Always keep the volume low enough to hear
outside sounds.
! Avoid exposure to moisture.
CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
60825-1:2007.
If you experience problems
Should this unit fail to work properly, please con-
tact your dealer or nearest authorized PIONEER
Service Station.
Before you start
2
Section
Before you start
En
01
Black plate (3,1)
Head unit
1 2 4 5
8 9
7 a c6 b d
3
1 h (eject)
2 iPod
3 1/
to 6/
4 Disc loading slot
5 DISP
6 SRC/OFF
7 BAND/
(iPod control)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(back)/DIMMER (dimmer)
b
(list)
c AUX input jack (3.5 mm stereo jack)
d USB port
CAUTION
Use an optional Pioneer USB cable (CD-U50E)
to connect the USB storage device as any device
connected directly to the unit will protrude out
from the unit, which could be dangerous.
Display indication
31 4 86
a
2 5 7 9
b
1 (list)
2
(iPod control)
This units iPod function is operated from
your iPod.
3 Sub information section
4 TA (traffic announcements)
5 TP (traffic program identification)
6
(sound retriever)
7 LOC (local seek tuning)
8
(repeat)
9
(random)
a
Main information section
! Tuner: band and frequency
! RDS: program service name, PTY infor-
mation and other literal information
! CD player, USB storage device and iPod:
elapsed playback time and text informa-
tion
b
Appears when a lower tier of folder or menu
exists.
Set up menu
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
2 Turn M.C. to switch to YES.
# If you do not use the unit for 30 seconds, the set
up menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO.
3 Press M.C. to select.
4 Follow these steps to set the menu.
To proceed to the next menu option, you need to
confirm your selection.
LANGUAGE (multi-language)
This unit can display the text information from a
compressed audio file even for information em-
bedded in English, Russian or Turkish.
! If the embedded language and the selected
language setting are not the same, text infor-
mation may not display properly.
! Some characters may not be displayed prop-
erly.
1 Turn M.C. to select the desired setting.
ENG (English)РУС (Russian)TUR (Turk-
ish)
2 Press M.C. to confirm the selection.
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Use FM STEP to set FM tuning step options (seek
step settings).
1 Turn M.C. to select the FM tuning step.
100 (100 kHz)50 (50 kHz)
2 Press M.C. to confirm the selection.
QUIT appears.
! The manual tuning step is fixed at 50 kHz.
! When AF and TA are turned off, the seek step
is fixed at 50 kHz even if set to 100.
5 To finish your settings, turn M.C. to select
YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO.
6 Press M.C. to select.
Notes
! You can set up the menu options from the
system menu and initial menu. For details
about the settings, refer to System menu on
page 8 and Initial menu on page 9.
! You can cancel set up menu by pressing
SRC/OFF.
Basic operations
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns
off.
Selecting a source
1 Press SRC/OFF to cycle between:
RADIOCDUSB/iPodAPP (application)
AUX
! USB MTP displays while the MTP connection
is in use.
! When there is an iPod connected and a source
other than iPod is selected, you can switch to
iPod by pressing iPod.
Adjusting the volume
1 Turn M.C. to adjust the volume.
Note
When this units blue/white lead is connected to
the vehicles auto-antenna relay control termi-
nal, the vehicles antenna extends when this
units source is turned on. To retract the anten-
na, turn the source off.
English
Using this unit
3
Section
Using this unit
En
02
Black plate (4,1)
Frequently used menu
operations
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1 Press
/DIMMER.
Returning to the ordinary display
Canceling the main menu
1 Press BAND/
.
Returning to the ordinary display from the list
1 Press BAND/
.
Radio
Basic operations
Selecting a band
1 Press BAND/
until the desired band (FM1,
FM2,FM3 for FM or MW/LW) is displayed.
Switching preset stations
1 Press c or d.
! Select PCH (preset channel) under SEEK to
use this function.
Manual tuning (step by step)
1 Press c or d.
! Select MAN (manual tuning) under SEEK to
use this function.
Seeking
1 Press and hold c or d, and then release.
You can cancel seek tuning by briefly pressing
c or d.
While pressing and holding c or d, you can
skip stations. Seek tuning starts as soon as
you release c or d.
Notes
! For details about SEEK, refer to SEEK (left/
right key setting) on page 5.
! This units AF (alternative frequencies
search) function can be turned on and off.
AF should be off for normal tuning operation
(refer to AF (alternative frequencies search)
on page 4).
Storing and recalling stations
for each band
Using preset tuning buttons
1 To store: Press and hold down one of the
preset tuning buttons (1/
to 6/ ) until
the number stops flashing.
2 To recall: Press one of the preset tuning
buttons (1/
to 6/ ).
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! FREQUENCY (program service name or
frequency)
! BRDCST INFO (program service name/PTY
information)
! CLOCK (source name and clock)
Notes
! If the program service name cannot be ac-
quired in FREQUENCY, the broadcast fre-
quency is displayed instead. If the program
service name is detected, the program serv-
ice name will be displayed.
! Depending on the band, text information can
be changed.
! Text information items that can be changed
depend on the area.
Using PTY functions
You can tune in to a station using PTY (program
type) information.
Searching for an RDS station by PTY information
1 Press
(list).
2 Turn M.C. to select a program type.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Press M.C. to begin the search.
The unit searches for a station broadcasting
that type of program. When a station is found,
its program service name is displayed.
! To cancel the search, press M.C. again.
! The program of some stations may differ
from that indicated by the transmitted PTY.
! If no station is broadcasting the type of
program you searched for, NOT FOUND is
displayed for about two seconds and then
the tuner returns to the original station.
PTY list
For more details about PTY list, visit the follow-
ing site:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
# If MW/LW band is selected, only BSM, LOCAL
and SEEK are available.
FM SETTING (FM sound quality settings)
The sound quality level can be set to match the
broadcast signal conditions of the FM band sig-
nal.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
! STANDARD This is the standard setting.
! HI-FI This is the setting to use to prioritize
the high quality of stereo sound.
! STABLE This is the setting to use to priori-
tize the low noise of monaural sound.
BSM (best stations memory)
BSM (best stations memory) automatically stores
the six strongest stations in the order of their sig-
nal strength.
1 Press M.C. to turn BSM on.
To cancel, press M.C. again.
REGIONAL (regional)
When AF is used, the regional function limits the
selection of stations to those broadcasting region-
al programs.
1 Press M.C. to turn the regional function on or
off.
LOCAL (local seek tuning)
Local seek tuning allows you to tune in to only
those radio stations with sufficiently strong sig-
nals for good reception.
1 Press M.C. to select the desired setting.
FM: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
The highest level setting allows reception of
only the strongest stations, while lower levels
allow the reception of weaker stations.
TA (traffic announcement standby)
1 Press M.C. to turn traffic announcement
standby on or off.
AF (alternative frequencies search)
Using this unit
4
Section
Using this unit
En
02
Black plate (5,1)
1 Press M.C. to turn AF on or off.
NEWS (news program interruption)
1 Press M.C. to turn the NEWS function on or
off.
SEEK (left/right key setting)
You can assign a function to the left and right keys
of the unit.
Select MAN (manual tuning) to tune up or down
manually or select PCH (preset channel) to switch
between preset channels.
1 Press M.C. to select MAN or PCH.
CD/CD-R/CD-RW and USB
storage devices
MTP connection
MTP-compatible Android devices (running
Android OS 4.0 or higher) can be connected by
MTP connection using the USB source. To con-
nect an Android device, use the cable that came
with the device.
Note
This function is not compatible with WAV.
Basic operations
Playing a CD/CD-R/CD-RW
1 Insert the disc into the disc loading slot with
the label side up.
Ejecting a CD/CD-R/CD-RW
1 Press h.
Playing songs on a USB storage device
1 Open the USB port cover.
2 Plug in the USB storage device using a USB
cable.
Stopping playback of files on a USB storage de-
vice
1 You may disconnect the USB storage device at
any time.
Selecting a folder
1 Press 1/
or 2/ .
Selecting a track
1 Press c or d.
Fast forwarding or reversing
1 Press and hold c or d.
! When playing compressed audio, there is no
sound during fast forward or reverse.
Returning to root folder
1 Press and hold BAND/
.
Switching between compressed audio and CD-DA
1 Press BAND/
.
Switching between playback memory devices
You can switch between playback memory devices
on USB storage devices with more than one Mass
Storage Device-compatible memory device.
1 Press BAND/
.
! You can switch between up to 32 different
memory devices.
Note
Disconnect USB storage devices from the unit
when not in use.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
CD-DA
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
CD-TEXT
! TRACK INFO (track title/track artist/disc
title)
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
MP3/WMA/WAV
! TRACK INFO (track title/artist name/album
title)
! FILE INFO (file name/folder name)
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Selecting and playing files/
tracks from the name list
1 Press to switch to the file/track name
list mode.
2 Use M.C. to select the desired file name
(or folder name).
Selecting a file or folder
1 Turn M.C.
Playing
1 When a file or track is selected, press M.C.
Viewing a list of the files (or folders) in the se-
lected folder
1 When a folder is selected, press M.C.
Playing a song in the selected folder
1 When a folder is selected, press and hold M.C.
Operations using special buttons
Selecting a repeat play range
1 Press 6/
to cycle between the following:
CD/CD-R/CD-RW
! ALL Repeat all tracks
! ONE Repeat the current track
! FLD Repeat the current folder
USB storage device
! ALL Repeat all files
! ONE Repeat the current file
! FLD Repeat the current folder
Playing tracks in random order
1 Press 5/
to turn random play on or off.
Tracks in a selected repeat range are played in
random order.
! To change songs during random play, press d
to switch to the next track. Pressing c restarts
playback of the current track from the begin-
ning of the song.
Pausing playback
1 Press 4/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
12OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Function settings
1 Press M.C. to display the main menu.
English
Using this unit
5
Section
Using this unit
En
02
Black plate (6,1)
2 Turn M.C. to change the menu option
and press to select FUNCTION.
Once selected, the function below can be ad-
justed.
S.RTRV (sound retriever)
Automatically enhances compressed audio and
restores rich sound.
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 5.
iPod
Basic operations
Playing songs on an iPod
1 Open the USB port cover.
2 Connect an iPod to USB input.
Playback is performed automatically.
Selecting a song (chapter)
1 Press c or d.
Selecting an album
1 Press 1/
or 2/ .
Fast forwarding or reversing
1 Press and hold c or d.
Notes
! The iPod cannot be turned on or off when the
control mode is set to CTRL AUDIO.
! Disconnect headphones from the iPod be-
fore connecting it to this unit.
! The iPod will turn off about two minutes after
the ignition is switched off.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! TRACK INFO (track title/artist name/album
title)
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Browsing for a song
1 Press to switch to the top menu of list
search.
2 Use M.C. to select a category/song.
Changing the name of the song or category
1 Turn M.C.
Playlistsartistsalbumssongspodcasts
genrescomposersaudiobooks
Playing
1 When a song is selected, press M.C.
Viewing a list of songs in the selected category
1 When a category is selected, press M.C.
Playing a song in the selected category
1 When a category is selected, press and hold
M.C.
Searching the list by alphabet
1 When a list for the selected category is dis-
played, press
to switch to alphabet search
mode.
! You also can switch to alphabet search
mode by turning M.C. twice.
2 Turn M.C. to select a letter.
3 Press M.C. to display the alphabetical list.
! To cancel searching, press
/DIMMER.
Notes
! You can play playlists created with the com-
puter application (MusicSphere). The appli-
cation will be available on our website.
! Playlists that you created with the computer
application (MusicSphere) are displayed in
abbreviated form.
Operations using special buttons
Selecting a repeat play range
1 Press 6/
to cycle between the following:
! ONE Repeat the current song
! ALL Repeat all songs in the selected list
! When the control mode is set to CTRL iPod,
the repeat play range will be same as what is
set for the connected iPod.
Selecting a random play range (shuffle)
1 Press 5/
to cycle between the following:
! SNG Play back songs in the selected list
in random order.
! ALB Play back songs from a randomly se-
lected album in order.
! OFF Not play back in random order.
Playing all songs in random order (shuffle all)
1 Press and hold 5/
to turn shuffle all on.
! To turn off shuffle all, select OFF in shuffle. For
details, refer to Selecting a random play range
(shuffle) on page 6.
Pausing playback
1 Press 4/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
12OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Playing songs related to the
currently playing song
You can play songs from the following lists.
Album list of the currently playing artist
Song list of the currently playing album
Album list of the currently playing genre
1 Press and hold
to switch to link play
mode.
2 Turn M.C. to change the mode; press to
select.
! ARTIST Plays an album by the artist cur-
rently playing.
! ALBUM Plays a song from the album cur-
rently being played.
! GENRE Plays an album from the genre cur-
rently being played.
The selected song/album will be played after the
currently playing song.
Notes
! The selected song/album may be canceled if
you use functions other than link search (e.g.
fast forward and reverse).
! Depending on the song selected to play, the
end of the currently playing song and the be-
ginning of the selected song/album may be
cut off.
Using this units iPod function
from your iPod
This units iPod function can be controlled by
using the connected iPod.
CTRL iPod is not compatible with the following
iPod models.
! iPod nano 1st generation
! iPod with video
% Press BAND/
to switch the control
mode.
! CTRL iPod This units iPod function can be
operated from the connected iPod.
Using this unit
6
Section
Using this unit
En
02
Black plate (7,1)
! CTRL AUDIO This units iPod function can
be controlled by using this unit.
You can also switch the control mode by press-
ing iPod.
Notes
! Switching the control mode to CTRL iPod
pauses song playback. Use the iPod to re-
sume playback.
! The following operations are still accessible
from the unit even if the control mode is set
to CTRL iPod.
Pausing
Fast forward/reverse
Selecting a song (chapter)
! The volume can only be adjusted from this
unit.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
! AUDIO BOOK is not available when
CTRL iPod is selected in the control mode.
For details, refer to Using this units iPod func-
tion from your iPod on page 6.
AUDIO BOOK (audiobook speed)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select your favorite setting.
! FASTER Playback at a speed faster than
normal
! NORMAL Playback at normal speed
! SLOWER Playback at a speed slower
than normal
S.RTRV (sound retriever)
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 6.
Using connected device
applications
You can use this unit to perform streaming play-
back of and control tracks in iPhone applica-
tions or just for streaming playback.
Important
Use of third party apps may involve or require
the provision of personally identifiable infor-
mation, whether through the creation of a
user account or otherwise, and for certain ap-
plications, the provision of geolocation data.
ALL THIRD PARTY APPS ARE THE SOLE RE-
SPONSIBILITY OF THE PROVIDERS, INCLUD-
ING WITHOUT LIMITATION COLLECTION AND
SECURITY OF USER DATA AND PRIVACY
PRACTICES. BY ACCESSING THIRD PARTY
APPS, YOU AGREE TO REVIEW THE TERMS
OF SERVICE AND PRIVACY POLICIES OF THE
PROVIDERS. IF YOU DO NOT AGREE WITH
THE TERMS OR POLICIES OF ANY PROVIDER
OR DO NOT CONSENT TO THE USE OF GEO-
LOCATION DATA WHERE APPLICABLE, DO
NOT USE THAT THIRD PARTY APP.
Information for compatibility of
connected devices
The following is the detailed information regard-
ing the terminals required to use the application
for iPhone on this unit.
For iPhone users
! This function is compatible with iPhone and
iPod touch.
! The device has iOS 5.0 or higher.
Notes
! Please check our website for a list of sup-
ported iPhone applications for this unit.
! Pioneer is not liable for any issues that may
arise from incorrect or flawed app-based
content.
! The content and functionality of the sup-
ported applications are the responsibility of
the App providers.
Starting procedure for iPhone users
1 Connect an iPhone to USB input.
2 Switch the source to APP.
3 Start up the application on the iPhone
and initiate playback.
Basic operations
Selecting a track
1 Press c or d.
Fast forwarding or reversing
1 Press and hold c or d.
Pausing playback
1 Press BAND/
to pause or resume.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! TRACK INFO (track title/artist name/album
title)
! APP NAME (application name)
! ELAPSED TIME (playback time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
PAUSE (pause)
1 Press M.C. to pause or resume.
S.RTRV (sound retriever)
1 Press M.C. to select the desired setting.
12OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Audio adjustments
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select AUDIO.
3 Turn M.C. to select the audio function.
Once selected, the following audio functions
can be adjusted.
! FADER is not available when SUB.W/SUB.W
is selected in SP-P/O MODE. For details, refer
to SP-P/O MODE (rear output and preout set-
ting) on page 9.
! SUB.W and SUB.W CTRL are not available
when REAR/REAR is selected in
SP-P/O MODE. For details, refer to
SP-P/O MODE (rear output and preout set-
ting) on page 9.
! SUB.W CTRL is not available when SUB.W is
selected in OFF. For details, refer to SUB.W
(subwoofer on/off setting) on page 8.
English
Using this unit
7
Section
Using this unit
En
02
Black plate (8,1)
! SLA is not available when FM is selected as
the source.
FADER (fader adjustment)
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the front/rear speaker bal-
ance.
BALANCE (balance adjustment)
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the left/right speaker bal-
ance.
EQ SETTING (equalizer recall)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the equalizer.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
The equalizer band and equalizer level can be
customized when CUSTOM1 or CUSTOM2 is
selected.
If selecting CUSTOM1 or CUSTOM2, complete
the procedures outlined below. If selecting
other options, press M.C. to return to the pre-
vious display.
! CUSTOM1 can be set separately for each
source. However, USB, iPod and APP are
all set to the same setting automatically.
! CUSTOM2 is a shared setting used in com-
mon for all sources.
3 Press M.C. to display the setting mode.
4 Press M.C. to cycle between the following:
Equalizer bandEqualizer level
5 Turn M.C. to select the desired setting.
Equalizer band: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizer level: +6 to 6
LOUDNESS (loudness)
Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1 Press M.C. to select the desired setting.
OFF (off)LOW (low)MID (mid)HI (high)
SUB.W (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to select the desired setting.
NOR (normal phase)REV (reverse phase)
OFF (subwoofer off)
SUB.W CTRL (subwoofer adjustment)
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequencyOutput levelSlope level
Rates that can be adjusted will flash.
3 Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Output level: 24 to +6
Slope level: 12 24
BASS BOOST (bass boost)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
HPF SETTING (high pass filter adjustment)
Use this function when wanting to listen only to
high-frequency sounds. Only frequencies higher
than the high-pass filter (HPF) cutoff are output
from the speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequencySlope level
3 Turn M.C. to select the desired setting.
Cut-off frequency: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Slope level: 12 24
SLA (source level adjustment)
This function prevents the volume from changing
too dramatically when the source switches.
! Settings are based on the FM volume level,
which remains unchanged.
! The MW/LW volume level can also be adjusted
with this function.
! USB, iPod and APP are all set to the same set-
ting automatically.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to 4
System menu
Important
PW SAVE (power saving) is canceled if the ve-
hicle battery is disconnected and will need to be
turned back on once the battery is reconnected.
When PW SAVE (power saving) is off, depend-
ing on connection methods, the unit may con-
tinue to draw power from the battery if your
vehicles ignition doesnt have an ACC (acces-
sory) position.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to select the system menu
function.
Once selected, the following system menu func-
tions can be adjusted.
LANGUAGE (multi-language)
1 Press M.C. to select the desired setting.
ENG (English)РУС (Russian)TUR (Turk-
ish)
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock
display you wish to set.
HourMinute
3 Turn M.C. to adjust the clock.
12H/24H (time notation)
1 Press M.C. to select the desired setting.
12H (12-hour clock)24H (24-hour clock)
AUTO PI (auto PI seek)
The unit can automatically search for a different
station with the same programming, even during
preset recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
Activate this setting when using an auxiliar y de-
vice connected to this unit.
1 Press M.C. to turn AUX on or off.
DIMMER (dimmer)
1 Press M.C. to turn the dimmer on or off.
! You can also change the dimmer setting by
pressing and holding
/DIMMER.
MUTE MODE (mute mode)
Using this unit
8
Section
Using this unit
En
02
Black plate (9,1)
Sound from this system is automatically muted or
attenuated when a signal from equipment with a
mute function is received.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
! MUTE Muting
! 20dB ATT Attenuation (20dB ATT has a
stronger effect than 10dB ATT)
! 10dB ATT Attenuation
PW SAVE (power saving)
Switching this function on enables you to reduce
the consumption of battery power.
! Turning on the source is the only operation al-
lowed when this function is on.
1 Press M.C. to turn the power save on or off.
Initial menu
1 Press and hold SRC/OFF until the unit
turns off.
2 Press and hold SRC/OFF until the main
menu appears in the display.
3 Turn M.C. to change the menu option
and press to select INITIAL.
4 Turn M.C. to select the initial menu func-
tion.
Once selected, the following initial menu func-
tions can be adjusted.
FM STEP (FM tuning step)
1 Press M.C. to select the FM tuning step.
100 (100 kHz)50 (50 kHz)
SP-P/O MODE (rear output and preout setting)
The rear speaker leads output and the RCA output
of this unit can be used to connect a full-range
speaker or subwoofer. Select a suitable option for
your connection.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
! REAR/SUB.W Select when there is a full-
range speaker connected to the rear speak-
er leads output and there is a subwoofer
connected to the RCA output.
! SUB.W/SUB.W Select when there is a
subwoofer connected directly to the rear
speaker leads output without any auxiliary
amp and there is a subwoofer connected
to the RCA output.
! REAR/REAR Select when there is a full-
range speaker connected to the rear speak-
er leads output and the RCA output.
If there is a full-range speaker connected to
the rear speaker leads output and the RCA
output is not used, you may select either
REAR/SUB.W or REAR/REAR.
System menu
1 Press and hold SRC/OFF until the unit
turns off.
2 Press and hold SRC/OFF until the main
menu appears in the display.
3 Turn M.C. to change the menu option
and press to select SYSTEM.
4 Turn M.C. to select the system menu
function.
For details, refer to System menu on page 8.
Using an AUX source
1 Insert the stereo mini plug into the AUX
input jack.
2 Press SRC/OFF to select AUX as the
source.
Note
AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to AUX
(auxiliary input) on page 8.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! Source name
! Source name and clock
If an unwanted display appears
Turn off the unwanted display using the proce-
dures listed below.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to display DEMO OFF and press
to select.
4 Turn M.C. to switch to YES.
5 Press M.C. to select.
English
Using this unit
9
Section
Using this unit
En
02
Black plate (10,1)
Connections
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! Use of this unit in conditions other than the
following could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4 W to
8 W (impedance value).
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
Disconnect the negative terminal of the bat-
tery before installation.
Secure the wiring with cable clamps or adhe-
sive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
Place all cables away from moving parts,
such as the shift lever and seat rails.
Place all cables away from hot places, such
as near the heater outlet.
Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
Use a fuse of the rating prescribed.
Never wire the negative speaker cable directly
to ground.
Never band together negative cables of multi-
ple speakers.
! When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an ex-
ternal power amp or the vehicles auto-anten-
na relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
! The black cable is ground. Ground cables for
this unit and other equipment (especially,
high-current products such as power amps)
must be wired separately. If they are not, an
accidental detachment may result in a fire or
malfunction.
This unit
3
1 24
5
1 Antenna input
2 Fuse (10 A)
3 Power cord input
4 Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
5 Rear output or subwoofer output
Power cord
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 To power cord input
2 Depending on the kind of vehicle, the func-
tion of 3 and 5 may be different. In this
case, be sure to connect 4 to 5 and 6 to
3.
3 Yellow
Back-up (or accessory)
4 Yellow
Connect to the constant 12 V supply termi-
nal.
5 Red
Accessory (or back-up)
6 Red
Connect to terminal controlled by ignition
switch (12 V DC).
7 Connect leads of the same color to each
other.
8 Black (chassis ground)
9 Blue/white
The pin position of the ISO connector will dif-
fer depending on the type of vehicle. Connect
9 and b when Pin 5 is an antenna control
type. In another type of vehicle, never con-
nect 9 and b.
a Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
b Blue/white
Connect to auto-antenna relay control termi-
nal (max. 300 mA 12 V DC).
c Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
d Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
e ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
Notes
! Change the initial menu of this unit. Refer to
SP-P/O MODE (rear output and preout set-
ting) on page 9.
The subwoofer output of this unit is monau-
ral.
! When using a subwoofer of 70 W (2 W), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
Installation
10
Section
Installation
En
03
Black plate (11,1)
Power amp (sold separately)
Perform these connections when using the op-
tional amplifier.
1
3
2
4
55
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Rear output or subwoofer output
5 Rear speaker or subwoofer
Installation
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
! Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
! Do not install this unit where:
it may interfere with operation of the vehicle.
it may cause injury to a passenger as a result
of a sudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
! When installing, to ensure proper heat dis-
persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not block-
ing the vents.
5cmcm
Leave ample
space
5 cm
5 cm
! Use commercially available parts when in-
stalling.
How to install
This unit can be installed properly using either
of the methods in the below list.
! Installation with the holder
! Installation using the screw holes on the side
of the unit
Before installing this unit
1 Remove the trim ring.
1
1 Trim ring
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3 Pull the unit out of the holder.
Remove the holder.
1
1 Holder
(factory-supplied part)
Installation with the holder
1 Install the holder into the dashboard.
After inserting the holder into the dashboard, se-
lect and bend the tabs appropriate to the thick-
ness of the dashboard material. (Install this unit
as firmly as possible using the top and bottom
tabs. To secure this unit, bend the tabs 90 de-
grees.)
1
2
1 Dashboard
2 Holder
(factory-supplied part)
2 Install this unit.
1
1 Dashboard
English
Installation
11
Section
Installation
En
03
Black plate (12,1)
3 Attach the trim ring.
1
1 Trim ring
Removing the holder
The procedure is the same as that for Before in-
stalling this unit. For details, refer to Before in-
stalling this unit on page 11.
Installation using the screw
holes on the side of the unit
% Fastening the unit to the factory radio-
mounting bracket.
Position the unit so that its screw holes are
aligned with the screw holes of the bracket, and
tighten the screws at three locations on each
side.
1
2
4
3
1 If the pawl gets in the way, bend it down.
2 Factory radio mounting bracket
3 Truss (5 mm × 8 mm) screws
4 Dashboard or console
Troubleshooting
Symptoms are written in bold and causes in reg-
ular, non-indented text. Regular, indented text is
used to indicate actions to be taken.
The display automatically returns to the ordinary
display.
You did not perform any operation within about 30
seconds.
Perform operation again.
The repeat play range changes unexpectedly.
Depending on the repeat play range, the selected
range may change when another folder or track is
being selected or during fast forwarding/reversing.
Select the repeat play range again.
A subfolder is not played back.
Subfolders cannot be played when FLD (folder re-
peat) is selected.
Select another repeat play range.
NO XXXX appears when a display is changed
(NO TITLE, for example).
There is no embedded text information.
Switch the display or play another track/file.
The unit is malfunctioning.
There is interference.
You are using a device, such as a cellular phone,
that may cause audible interference.
Move electrical devices that may be causing the
interference away from the unit.
Error messages
When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the error
message.
Error messages are written in bold and causes
in regular, non-indented text. Regular, indented
text is used to indicate actions to be taken.
Common
AMP ERROR
This unit fails to operate or the speaker connection is
incorrect; the protective circuit is activated.
Check the speaker connection. If the message
fails to disappear even after the engine is
switched off/on, contact your dealer or an
authorized Pioneer Service Station for
assistance.
CD player
ERROR-07, 11, 12, 17, 30
The disc is dirty.
Clean the disc.
The disc is scratched.
Replace the disc.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
There is an electrical or mechanical error.
Turn the ignition switch OFF and back ON, or
switch to a different source, then back to the CD
player.
ERROR-15
The inserted disc is blank.
Replace the disc.
ERROR-23
Unsupported CD format.
Replace the disc.
Installation
12
Section
Additional information
En
03
Black plate (13,1)
FORMAT READ
Sometimes there is a delay between the start of play-
back and when you start to hear any sound.
Wait until the message disappears and you hear
sound.
NO AUDIO
The inserted disc does not contain any playable files.
Replace the disc.
SKIPPED
The inserted disc contains DRM protected files.
The protected files are skipped.
PROTECT
All the files on the inserted disc are embedded with
DRM.
Replace the disc.
USB storage device/iPod
FORMAT READ
Sometimes there is a delay between the start of play-
back and when you start to hear any sound.
Wait until the message disappears and you hear
sound.
NO AUDIO
There are no songs.
Transfer the audio files to the USB storage device
and connect.
The connected USB storage device has security en-
abled.
Follow the USB storage device instructions to
disable the security.
SKIPPED
The connected USB storage device contains DRM
protected files.
The protected files are skipped.
PROTECT
All the files on the connected USB storage device
are embedded with DRM.
Replace the USB storage device.
N/A USB
The connected USB device is not supported by this
unit.
! Connect a USB Mass Storage Class compliant
device.
! Disconnect your device and replace it with a
compatible USB storage device.
CHECK USB
The USB connector or USB cable has short-
circuited.
Check that the USB connector or USB cable is
not caught in something or damaged.
CHECK USB
The connected USB storage device consumes more
than maximum allowable current.
Disconnect the USB storage device and do not
use it. Turn the ignition switch to OFF, then to
ACC or ON and then connect only compliant
USB storage devices.
CHECK USB
The iPod operates correctly but does not charge.
Make sure the connection cable for the iPod has
not shorted out (e.g., not caught in metal
objects). After checking, turn the ignition switch
OFF and back ON, or disconnect the iPod and
reconnect.
ERROR-19
Communication failed.
Perform one of the following operations.
Turn the ignition switch OFF and back ON.
Disconnect the USB storage device.
Change to a different source.
Then, return to the USB source.
iPod failure.
Disconnect the cable from the iPod. Once the
iPods main menu is displayed, reconnect the
iPod and reset it.
ERROR-23
USB storage device was not formatted with FAT12,
FAT16 or FAT32.
USB storage device should be formatted with
FAT12, FAT16 or FAT32.
ERROR-16
The iPod firmware version is old.
Update the iPod version.
iPod failure.
Disconnect the cable from the iPod. Once the
iPods main menu is displayed, reconnect the
iPod and reset it.
STOP
There are no songs in the current list.
Select a list that contains songs.
NOT FOUND
No related songs.
Transfer songs to the iPod.
Application
START UP APP
The application has not started running yet.
Follow the instructions that appear on the
screen.
Handling guidelines
Discs and player
Use only discs that feature either of the following
two logos.
Use 12-cm discs.
Use only conventional, fully circular discs.
The following types of discs cannot be used with
this unit:
! DualDiscs
! 8-cm discs: Attempts to use such discs with
an adapter may cause the unit to malfunction.
! Oddly shaped discs
! Discs other than CDs
! Damaged discs, including discs that are
cracked, chipped or warped
! CD-R/RW discs that have not been finalized
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Do not attach labels, write on or apply chemicals
to the surface of the discs.
To clean a CD, wipe the disc with a soft cloth out-
ward from the center.
Condensation may temporarily impair the players
performance. Let it rest for about one hour to ad-
just to a warmer temperature. Also, wipe any
damp discs off with a soft cloth.
English
Additional information
13
Appendix
Additional information
En
Black plate (14,1)
Playback of discs may not be possible because of
disc characteristics, disc format, recorded applica-
tion, playback environment, storage conditions,
and so on.
Road shocks may interrupt disc playback.
When using discs that can be printed on label sur-
faces, check the instructions and the warnings of
the discs. Depending on the discs, inserting and
ejecting may not be possible. Using such discs
may result in damage to this equipment.
Do not attach commercially available labels or
other materials to the discs.
! The discs may warp making the disc unplay-
able.
! The labels may come off during playback and
prevent ejection of the discs, which may result
in damage to the equipment.
USB storage device
Connections via USB hub are not supported.
Do not connect anything other than a USB stor-
age device.
Firmly secure the USB storage device when driv-
ing. Do not let the USB storage device fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Depending on the USB storage device, the follow-
ing problems may occur.
! Operations may vary.
! The storage device may not be recognized.
! Files may not be played back properly.
! The device may cause audible interference
when you are listening to the radio.
iPod
Do not leave the iPod in places with high tempera-
tures.
Firmly secure the iPod when driving. Do not let the
iPod fall onto the floor, where it may become
jammed under the brake or accelerator pedal.
About iPod settings
! When an iPod is connected, this unit changes
the EQ (equalizer) setting of the iPod to off in
order to optimize the acoustics. When you dis-
connect the iPod, the EQ returns to the original
setting.
! You cannot set Repeat to off on the iPod when
using this unit. Repeat is automatically
changed to All when the iPod is connected to
this unit.
Incompatible text saved on the iPod will not be dis-
played by the unit.
Compressed audio
compatibility (disc, USB)
WMA
File extension: .wma
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to
384 kbps (VBR)
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream with video: Not com-
patible
MP3
File extension: .mp3
Bit rate: 8 kbps to 320 kbps (CBR), VBR
Sampling frequency: 8 kHz to 48 kHz (32 kHz,
44.1 kHz, 48 kHz for emphasis)
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3 tag Version 2.x is given priority over Version
1.x.)
M3u playlist: Not compatible
MP3i (MP3 interactive), mp3 PRO: Not compatible
WAV
File extension: .wav
Quantization bits: 8 and 16 (LPCM), 4 (MS
ADPCM)
Sampling frequency: 16 kHz to 48 kHz (LPCM),
22.05 kHz and 44.1 kHz (MS ADPCM)
! You cannot use this function with USB MTP.
Supplemental information
Only the first 32 characters can be displayed as a
file name (including the file extension) or a folder
name.
Russian text to be displayed on this unit should be
encoded in one of the following character sets:
! Unicode (UTF-8, UTF-16)
! A character set other than Unicode that is
used in a Windows environment and is set to
Russian in the multi-language setting
This unit may not work properly depending on the
application used to encode WMA files.
There may be a slight delay at the start of playback
of audio files embedded with image data or audio
files stored on a USB storage device that has nu-
merous folder hierarchies.
Disc
Playable folder hierarchy: up to eight tiers (A prac-
tical hierarchy is less than two tiers.)
Playable folders: up to 99
Playable files: up to 999
File system: ISO 9660 Level 1 and 2, Romeo, Joliet
Multi-session playback: Compatible
Packet write data transfer: Not compatible
Regardless of the length of blank sections be-
tween the songs from the original recording, com-
pressed audio discs play with a short pause
between songs.
USB storage device
Playable folder hierarchy: up to eight tiers (A prac-
tical hierarchy is less than two tiers.)
Playable folders: up to 500
Playable files: up to 15 000
Playback of copyright-protected files: Not compati-
ble
Partitioned USB storage device: Only the first par-
tition can be played.
There may be a slight delay when starting play-
back of audio files on a USB storage device with
numerous folder hierarchies.
CAUTION
! Pioneer cannot guarantee compatibility with
all USB mass storage devices and assumes
no responsibility for any loss of data on
media players, smart phones, or other devi-
ces while using this product.
Additional information
14
Appendix
Additional information
En
Black plate (15,1)
! Do not leave discs or a USB storage device
in any place that is subject to high tempera-
tures.
iPod compatibility
This unit supports only the following iPod mod-
els.
Made for
! iPod touch (5th generation)
! iPod touch (4th generation)
! iPod touch (3rd generation)
! iPod touch (2nd generation)
! iPod touch (1st generation)
! iPod classic
! iPod with video
! iPod nano (7th generation)
! iPod nano (6th generation)
! iPod nano (5th generation)
! iPod nano (4th generation)
! iPod nano (3rd generation)
! iPod nano (2nd generation)
! iPod nano (1st generation)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Depending on the generation or version of the
iPod, some functions may not be available.
Operations may vary depending on the software
version of iPod.
Users of iPod with the Lightning Connector should
use the Lightning to USB Cable (supplied with
iPod).
Users of iPod with the Dock Connector should use
CD-IU51. For details, consult your dealer.
About the file/format compatibility, refer to the
iPod manuals.
Audiobook, Podcast: Compatible
CAUTION
Pioneer accepts no responsibility for data lost
on the iPod, even if that data is lost while this
unit is used.
Sequence of audio files
The user cannot assign folder numbers and
specify playback sequences with this unit.
Example of a hierarchy
Level 1 Level 2 Level 3 Level 4
01
02
03
04
05
: Folder
: Compressed
audio file
01 to 05: Folder
number
1 to 6: Playback
sequence
Disc
Folder selection sequence or other operation
may differ depending on the encoding or writing
software.
USB storage device
Playback sequence is the same as recorded se-
quence in the USB storage device.
To specify the playback sequence, the following
method is recommended.
1 Create a file name that includes numbers
that specify the playback sequence (e.g.,
001xxx.mp3 and 099yyy.mp3).
2 Put those files into a folder.
3 Save the folder containing files on the USB
storage device.
However, depending on the system environment,
you may not be able to specify the playback se-
quence.
For USB portable audio players, the sequence is
different and depends on the player.
Russian character chart
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Display C: Character
Copyright and trademark
MP3
Supply of this product only conveys a license for
private, non-commercial use and does not con-
vey a license nor imply any right to use this prod-
uct in any commercial (i.e. revenue-generating)
real time broadcasting (terrestrial, satellite,
cable and/or any other media), broadcasting/
streaming via internet, intranets and/or other
networks or in other electronic content distribu-
tion systems, such as pay-audio or audio-on-de-
mand applications. An independent license for
such use is required. For details, please visit
http://www.mp3licensing.com.
WMA
Windows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
iPod & iPhone
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
Lightning is a trademark of Apple Inc.
Made for iPod and Made for iPhone mean
that an electronic accessory has been designed
to connect specifically to iPod or iPhone, respec-
tively, and has been certified by the developer to
meet Apple performance standards. Apple is
not responsible for the operation of this device
or its compliance with safety and regulatory
standards. Please note that the use of this ac-
cessory with iPod or iPhone may affect wireless
performance.
Androidä
Android is a trademark of Google Inc.
English
Additional information
15
Appendix
Additional information
En
Black plate (16,1)
Specifications
General
Power source ................... 14.4 V DC (10.8 V to 15.1 V al-
lowable)
Grounding system ............ Negative type
Maximum current consumption
................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis ............................ 178mm × 100mm × 157 mm
Nose ................................ 188 mm × 118mm × 25mm
D
Chassis ............................ 178mm × 100mm × 165 mm
Nose ................................ 170 mm × 96mm × 17mm
Weight ............................. 1.2kg
Audio
Maximum power output ... 50 W × 4
70 W × 1/2 W (for subwoofer)
Continuous power output
................................... 22W × 4 (50Hz to 15000 Hz,
5 % THD, 4 W load, both chan-
nels driven)
Load impedance .............. 4 W (4 W to 8 W allowable)
Preout maximum output level
................................... 2.0V
Loudness contour ............ +10dB (100 Hz), +6.5 dB
(10 kHz) (volume: 30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequency ........................ 80Hz/250 Hz/800 Hz/2.5 kHz/
8 kHz
Equalization range ........... ±12 dB (2 dB step)
Subwoofer (mono):
Frequency ........................ 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Slope ............................... 12 dB/oct, 24 dB/oct
Gain ................................ +6dB to 24 dB
Phase .............................. Normal/Reverse
CD player
System ............................ Compact disc audio system
Usable discs .................... Compact disc
Signal-to-noise ra tio ......... 94dB (1 kHz) (IEC-A network)
Number of channels ........ 2 (stereo)
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch
audio)
(Windows Media Player)
WAV signal format ........... Linear PCM & MS ADPCM
(Non-compressed)
USB
USB standard specification
................................... USB 2.0 full speed
Maximum current supply
................................... 1 A
USB Class ....................... MSC (Mass Storage Class)
File system ....................... FAT12, FAT16, FAT32
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch
audio)
(Windows Media Player)
WAV signal format ........... Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
Frequency range .............. 87.5 MHz to 108.0 MHz
Usable sensitivity ............. 9dBf (0.8 µV/75 W, mono, S/N:
30 dB)
Signal-to-noise ra tio ......... 72dB (IEC-A network)
MW tuner
Frequency range .............. 531 kHz to 1602 kHz
Usable sensitivity ............. 25µV (S/N: 20 dB)
Signal-to-noise ra tio ......... 62dB (IEC-A network)
LW tuner
Frequency range .............. 153 kHz to 281kHz
Usable sensitivity ............. 28µV (S/N: 20 dB)
Signal-to-noise ra tio ......... 62dB (IEC-A network)
Note
Specifications and the design are subject to
modifications without notice.
Additional information
16
Appendix
En
Black plate (17,1)
English
17En
Black plate (18,1)
Nous vous remercions davoir acheté cet ap-
pareil PIONEER
Pour garantir une utilisation correcte, lisez bien
ce mode demploi avant dutiliser cet appareil. Il
est particulièrement important que vous lisiez et
respectiez les indications ATTENTION et PRÉ-
CAUTION de ce mode demploi. Conservez-le
dans un endroit sûr et facilement accessible pour
toute consultation ultérieure.
Si vous souhaitez vous débarrasser de cet ap-
pareil, ne le mettez pas à la poubelle avec vos
ordures ménagères. Il existe un système de
collecte séparé pour les appareils électroni-
ques usagés, qui doivent être récupérés, trai-
tés et recyclés conformément à la législation.
Dans les états membres de lUE, en Suisse et en
Norvège, les foyers domestiques peuvent rap-
porter leurs produits électroniques usagés gra-
tuitement à des points de collecte spécifiés ou à
un revendeur (sous réserve dachat dun produit
similaire).
Dans les pays qui ne sont pas mentionnés ci-
dessus, veuillez contacter les autorités locales
pour vous informer de la méthode correcte de
mise au rebut.
En agissant ainsi vous assurerez que le produit
que vous mettez au rebut est soumis au proces-
sus de traitement, de récupération et de recy-
clage nécessaire et éviterez ainsi les effets
négatifs potentiels sur lenvironnement et la
santé publique.
Quelques mots sur cet appareil
Les fréquences du syntoniseur de cet appareil
sont attribuées pour une utilisation en Europe
de lOuest, Asie, Moyen-Orient, Afrique et Océ-
anie. Son utilisation dans dautres régions peut
se traduire par une réception de mauvaise qua-
lité. La fonction RDS (radio data system) nest
opérationnelle que dans les régions des si-
gnaux RDS sont diffusés pour les stations FM.
ATTENTION
! Nessayez pas dinstaller cet appareil ou
den faire lentretien vous-même. Linstal-
lation ou lentretien de cet appareil par
des personnes sans formation et sans ex-
périence en équipement électronique et
en accessoires automobiles peut être
dangereux et vous exposer à des risques
délectrocution ou à dautres dangers.
! Nessayez pas de démonter ou de modifier
cet appareil. Veillez à quitter la route et garer
votre véhicule en lieu sûr avant dessayer du-
tiliser les commandes de lappareil.
PRÉCAUTION
! Ne laissez pas cet appareil entrer en contact
avec des liquides. Cela pourrait provoquer
une électrocution. Tout contact avec des li-
quides pourrait également provoquer des
dommages, de la fumée et une surchauffe
de lappareil.
! Le Pioneer CarStereo-Pass est utilisable seu-
lement en Allemagne.
! Maintenez le niveau découte à une valeur
telle que vous puissiez entendre les sons pro-
venant de lextérieur.
! Évitez tout contact avec lhumidité.
PRÉCAUTION
Cet appareil est un produit laser de Classe 1,
classé selon larticle IEC 60825-1:2007 relatif à
la Sécurité des produits laser.
APPAREIL À LASER DE CLASSE 1
Si vous rencontrez des
problèmes
En cas danomalie, veuillez contacter votre re-
vendeur ou le centre dentretien agréé par
PIONEER le plus proche.
Avant de commencer
18
Section
Avant de commencer
Fr
01
Black plate (19,1)
Appareil central
1 2 4 5
8 9
7 a c6 b d
3
1 h (éjection)
2 iPod
3 1/
à 6/
4 Fente de chargement des disques
5 DISP
6 SRC/OFF
7 BAND/
(contrôle de liPod)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(retour)/DIMMER (atténuateur de lumi-
nosité)
b
(liste)
c Jack dentrée AUX (jack stéréo 3,5 mm)
d Port USB
PRÉCAUTION
Utilisez un câble USB Pioneer optionnel (CD-
U50E) pour connecter le périphérique de stoc-
kage USB, faute de quoi ce dernier, comme
nimporte quel périphérique relié directement à
lappareil, dépasserait de lappareil et pourrait
savérer dangereux.
Indications affichées
31 4 86
a
2 5 7 9
b
1 (liste)
2
(contrôle de liPod)
La fonction iPod de cet appareil est utilisée
à partir de votre iPod.
3 Section dinformations secondaires
4 TA (bulletins dinformations routières)
5
TP (identification des programmes dinfor-
mations routières)
6
(sound retriever)
7
LOC (accord automatique sur une station lo-
cale)
8
(répétition de la lecture)
9
(lecture aléatoire)
a
Section dinformations principales
! Syntoniseur : gamme et fréquence
! RDS : nom du service de programme, in-
formations PTY et autres informations
textuelles
! Lecteur de CD, périphérique de stockage
USB et iPod : temps de lecture écoulé et
informations textuelles
b
Apparaît lorsquun niveau inférieur de dos-
sier ou de menu existe.
Menu de configuration
1 Après avoir installé lappareil, mettez le
contact dallumage sur ON.
SET UP saffiche.
2 Tournez M.C. pour passer à YES.
# Si vous nutilisez pas lappareil dans les 30 secon-
des environ, le menu de configuration ne saffichera
pas.
# Si vous préférez ne pas effectuer la configuration
pour linstant, tournez M.C. pour passer à NO.
3 Appuyez sur M.C. pour sélectionner.
4 Procédez comme suit pour définir le
menu.
Pour passer à la prochaine option de menu,
vous devez confirmer votre sélection.
LANGUAGE (multilingue)
Cet appareil peut afficher les informations textuel-
les dun fichier audio compressé même si elles
sont incorporées en anglais, en russe ou en turc.
! Si la langue incorporée et la langue sélection-
née sont différentes, les informations textuel-
les peuvent ne pas safficher correctement.
! Certains caractères peuvent ne pas safficher
correctement.
1 Tournez M.C. pour sélectionner le réglage sou-
haité.
ENG (Anglais)РУС (Russe)TUR (Turc)
2 Appuyez sur M.C. pour confirmer la sélection.
CLOCK SET (réglage de lhorloge)
1 Tournez M.C. pour régler lheure.
2 Appuyez sur M.C. pour sélectionner les minu-
tes.
3 Tournez M.C. pour régler les minutes.
4 Appuyez sur M.C. pour confirmer la sélection.
FM STEP (incrément daccord FM)
Utilisez FM STEP pour régler les options dincré-
ment daccord FM (recherchez les réglages de lin-
crément).
1 Tournez M.C. pour choisir lincrément daccord
FM.
100 (100 kHz) 50 (50 kHz)
2 Appuyez sur M.C. pour confirmer la sélection.
QUIT saffiche.
! Lincrément daccord manuel est défini sur
50 kHz.
! Quand les fonctions AF et TA sont toutes deux
désactivées, lincrément daccord est défini
sur 50 kHz même sil est réglé sur 100.
5 Pour terminer la configuration, tournez
M.C. pour sélectionner YES.
# Si vous souhaitez modifier à nouveau le réglage,
tournez M.C. pour passer à NO.
6 Appuyez sur M.C. pour sélectionner.
Français
Utilisation de cet appareil
19
Section
Utilisation de cet appareil
Fr
02
Black plate (20,1)
Remarques
! Vous pouvez configurer les options de menu
à partir du menu système et du menu initial.
Pour des détails sur les réglages, reportez-
vous à la page 26, Menu système et la page
26, Menu initial.
! Vous pouvez annuler le menu de configura-
tion en appuyant sur SRC/OFF.
Opérations de base
Mise en service de lappareil
1 Appuyez sur SRC/OFF pour mettre en service
lappareil.
Mise hors service de lappareil
1 Maintenez la pression sur SRC/OFF jusquàce
que lappareil soit mis hors tension.
Choix dune source
1 Appuyez sur SRC/OFF pour parcourir les op-
tions disponibles :
RADIOCDUSB/iPodAPP (application)
AUX
! USB MTP apparaît lorsque la connexion MTP
est en cours dutilisation.
! Lorsquun iPod est connecté et quune source
autre que iPod est sélectionnée, vous pouvez
basculer sur iPod en appuyant sur iPod.
Réglage du volume
1 Tournez M.C. pour régler le volume.
Remarque
Si le fil bleu/blanc de lappareil est relié à la
prise de commande du relais de lantenne moto-
risée du véhicule, celle-ci se déploie lorsque la
source est mise en service. Pour rétracter lan-
tenne, mettez la source hors service.
Opérations de menu
fréquemment utilisées
Retour à laffichage précédent
Retour à la liste précédente (le dossier de niveau
immédiatement supérieur)
1 Appuyez sur
/DIMMER.
Retour à laffichage ordinaire
Annulation du menu principal
1 Appuyez sur BAND/
.
Retour à laffichage ordinaire à partir de la liste
1 Appuyez sur BAND/
.
Radio
Opérations de base
Sélection dune gamme
1 Appuyez sur BAND/
jusquà ce que la
gamme désirée (FM1, FM2, FM3 en FM ou
MW/LW (PO/GO)) saffiche.
Changement de fréquence en mémoire
1 Appuyez sur c ou d.
! Sélectionnez PCH (canal présélectionné) sous
SEEK pour utiliser cette fonction.
Accord manuel (pas à pas)
1 Appuyez sur c ou d.
! Sélectionnez MAN (accord manuel) sous
SEEK pour utiliser cette fonction.
Recherche
1 Appuyez de manière prolongée sur c ou d,
puis relâchez.
Vous pouvez annuler laccord automatique en
appuyant brièvement sur c ou d.
Lorsque vous appuyez de manière prolongée
sur c ou d, vous pouvez sauter des stations.
Laccord automatique démarre dès que vous
relâchez c ou d.
Remarques
! Pour des détails sur SEEK, reportez-vous à la
page 21, SEEK (réglage de la touche droite/
gauche).
! La fonction AF (recherche des autres fré-
quences possibles) de cet appareil peut être
mise en service ou hors service. La fonction
AF doit être hors service pendant une opéra-
tion daccord normal (reportez-vous à la
page 21, AF (recherche des autres fréquences
possibles)).
Enregistrement et rappel des
stations pour chaque gamme
Utilisation des touches de présélection
1 Pour la mise en mémoire : Appuyez de
façon prolongée sur lune des touches de
présélection (1/
à6/ ) jusquà ce que le
numéro cesse de clignoter.
2 Pour le rappel : Appuyez sur une des tou-
ches de présélection (1/
à6/ ).
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! FREQUENCY (nom du service de pro-
gramme ou fréquence)
! BRDCST INFO (nom du service de pro-
gramme/informations PTY)
! CLOCK (nom de la source et horloge)
Remarques
! Si le nom du service de programme ne peut
pas être acquis dans FREQUENCY, la fré-
quence démission saffiche alors. Si le nom
du service de programme est détecté, celui-
ci saffiche.
! En fonction de la gamme sélectionnée, les
informations textuelles peuvent être différen-
tes.
! Les informations textuelles pouvant être mo-
difiées dépendent de la région.
Utilisation des fonctions PTY
Vous pouvez rechercher une station à laide de
son code PTY (type de programme).
Recherche dune station RDS en utilisant le code
PTY
1 Appuyez sur
(liste).
2 Tournez M.C. pour sélectionner le type de pro-
gramme.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Appuyez sur M.C. pour lancer la recherche.
Cet appareil recherche une station qui diffuse
ce type de programme. Quand une station est
trouvée, son nom de service de programme
est affiché.
! Appuyez à nouveau sur M.C. pour aban-
donner la recherche.
! Le type de lémission captée peut différer
de celui indiqué par le code PTY transmis.
! Si aucune station ne diffuse démission du
type choisi, lindication NOT FOUND saffi-
che pendant environ deux secondes puis
le syntoniseur saccorde sur la fréquence
dorigine.
Liste des codes PTY
Pour plus de détails sur la liste PTY, visitez le site
suivant :
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
Utilisation de cet appareil
20
Section
Utilisation de cet appareil
Fr
02
Black plate (21,1)
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
3 Tournez M.C. pour sélectionner la fonc-
tion.
Une fois sélectionnées, les fonctions suivantes
peuvent être ajustées.
# Si la gamme MW/LW (PO/GO) est sélectionnée,
seuls BSM, LOCAL et SEEK sont disponibles.
FM SETTING (réglages de qualité sonore FM)
Le niveau de qualité sonore peut être réglé afin de
correspondre aux conditions du signal démission
de la gamme FM.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le réglage sou-
haité.
! STANDARD Il sagit du réglage standard.
! HI-FI Il sagit du réglage à utiliser pour
donner la priorité à la qualité supérieure du
son stéréo.
! STABLE Il sagit du réglage à utiliser pour
donner la priorité au faible bruit du son
monaural.
BSM (mémoire des meilleures stations)
La fonction BSM (mémoire des meilleures sta-
tions) mémorise automatiquement les six stations
les plus fortes dans lordre de la force du signal.
1 Appuyez sur M.C. pour mettre la fonction BSM
en service.
Pour annuler, appuyez à nouveau sur M.C.
REGIONAL (stations régionales)
Quand la fonction AF est utilisée, la fonction de re-
cherche des stations régionales limite la sélection
aux stations qui diffusent des programmes régio-
naux.
1 Appuyez sur M.C. pour mettre la fonction de
recherche des stations régionales en service
ou hors service.
LOCAL (accord automatique sur une station lo-
cale)
Laccord automatique sur une station locale ne
sintéresse quaux stations de radio dont le signal
reçu est suffisamment puissant pour garantir une
réception de bonne qualité.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
FM : OFFLV1LV2LV3LV4
MW/LW (PO/GO) : OFFLV1LV2
La valeur la plus élevée permet la réception
des seules stations très puissantes ; les autres
valeurs autorisent la réception de stations
moins puissantes.
TA (attente de bulletins dinformations routières)
1 Appuyez sur M.C. pour mettre en service ou
hors service lattente dun bulletin dinforma-
tions routières.
AF (recherche des autres fréquences possibles)
1 Appuyez sur M.C. pour mettre la fonction AF
en service ou hors service.
NEWS (interruption pour réception dun bulletin
dinformations)
1 Appuyez sur M.C. pour mettre la fonction
NEWS (bulletin dinformations) en service ou
hors service.
SEEK (réglage de la touche droite/gauche)
Vous pouvez assigner une fonction aux touches
droite et gauche de lappareil.
Sélectionnez MAN (accord manuel) pour effectuer
un accord de fréquence manuellement ou sélec-
tionnez PCH (canaux présélectionnés) pour chan-
ger de canal présélectionné.
1 Appuyez sur M.C. pour sélectionner MAN ou
PCH.
CD/CD-R/CD-RW et
périphériques de stockage USB
Connexion MTP
Il est possible de connecter des périphériques
Android compatibles MTP (utilisant le système
dexploitation Android 4.0 ou version supérieure)
via une connexion MTP à laide de la source
USB. Pour connecter un périphérique Android,
utilisez le câble fourni avec lappareil.
Remarque
Cette fonction nest pas compatible avec WAV.
Opérations de base
Lecture dun CD/CD-R/CD-RW
1 Introduisez un disque, létiquette vers le haut,
dans le logement de chargement des disques.
Éjection dun CD/CD-R/CD-RW
1 Appuyez sur h.
Lecture de plages musicales sur un périphérique
de stockage USB
1 Ouvrez le capot du port USB.
2 Branchez le périphérique de stockage USB en
utilisant un câble USB.
Arrêt de la lecture de fichiers sur un périphérique
de stockage USB
1 Vous pouvez débrancher le périphérique de
stockage USB à tout moment.
Sélection dun dossier
1 Appuyez sur 1/
ou 2/ .
Sélection dune plage
1 Appuyez sur c ou d.
Avance ou retour rapide
1 Appuyez de manière prolongée sur c ou d.
! Lors de la lecture dun disque daudio
compressé, aucun son nest émis pendant la-
vance ou le retour rapide.
Retour au dossier racine
1 Appuyez sur BAND/
de façon prolongée.
Commutation entre les modes audio compressé
et CD-DA
1 Appuyez sur BAND/
.
Changement de périphérique de mémoire de lec-
ture
Vous pouvez basculer entre les périphériques de
mémoire sur les périphériques de stockage USB
ayant plus dun périphérique de mémoire compa-
tible avec la norme Mass Storage Class pour ef-
fectuer la lecture.
1 Appuyez sur BAND/
.
! Vous pouvez basculer entre 32 différents péri-
phériques de mémoire maximum.
Remarque
Débranchez les périphériques de stockage USB
de lappareil lorsque vous ne lutilisez pas.
Français
Utilisation de cet appareil
21
Section
Utilisation de cet appareil
Fr
02
Black plate (22,1)
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
CD-DA
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
CD-TEXT
! TRACK INFO (titre de la plage/interprète
de la plage/titre du disque)
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
MP3/WMA/WAV
! TRACK INFO (titre de la plage/nom de lin-
terprète/nom de lalbum)
! FILE INFO (nom du fichier/nom du dossier)
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
Sélection et lecture des fichiers/
plages à partir de la liste des noms
1 Appuyez sur pour passer en mode
liste des noms de fichiers/plages.
2 Utilisez M.C. pour sélectionner le nom de
fichier (ou nom de dossier) souhaité.
Sélection dun fichier ou dun dossier
1 Tournez M.C.
Lecture
1 Lorsquun fichier ou une plage est sélection-
né(e), appuyez sur M.C.
Affichage dune liste des fichiers (ou des dossiers)
dans le dossier sélectionné
1 Quand un dossier est sélectionné, appuyez sur
M.C.
Lecture dune plage musicale dans le dossier sé-
lectionné
1 Quand un dossier est sélectionné, appuyez de
manière prolongée sur M.C.
Opérations à laide de touches
spéciales
Sélection dune étendue de répétition de lecture
1 Appuyez sur 6/
pour parcourir les options
disponibles :
CD/CD-R/CD-RW
! ALL Répétition de toutes les plages
! ONE Répétition de la plage en cours de
lecture
! FLD Répétition du dossier en cours de
lecture
Périphérique de stockage USB
! ALL Répétition de tous les fichiers
! ONE Répétition du fichier en cours de
lecture
! FLD Répétition du dossier en cours de
lecture
Lecture des plages dans un ordre aléatoire
1 Appuyez sur 5/
pour activer ou désactiver
la lecture aléatoire.
Les plages dune étendue de répétition sélec-
tionnée sont lues dans un ordre aléatoire.
! Pour changer de plage musicale pendant une
lecture aléatoire, appuyez sur d pour passer à
la plage suivante. Appuyez sur c pour redé-
marrer la lecture de la plage en cours au
début de la plage musicale.
Pause de la lecture
1 Appuyez sur 4/PAUSE pour mettre en pause
ou reprendre la lecture.
Amélioration de laudio compressé et restauration
dun son riche (sound retriever (correcteur de son
compressé))
1 Appuyez sur 3/S.Rtrv pour parcourir les op-
tions disponibles :
12OFF (hors service)
1 est efficace pour les faibles taux de compres-
sion et 2 est efficace pour les taux de compres-
sion élevés.
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
Une fois sélectionnée, la fonction ci-dessous
peut être ajustée.
S.RTRV (sound retriever)
Améliore automatiquement laudio compressé et
restaure un son riche.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
Pour les détails, reportez-vous à la page 22,
Amélioration de laudio compressé et restaura-
tion dun son riche (sound retriever (correcteur
de son compressé)).
iPod
Opérations de base
Lecture de plages musicales sur un iPod
1 Ouvrez le capot du port USB.
2 Connectez un iPod à lentrée USB.
La lecture seffectue automatiquement.
Sélection dune plage musicale (dun chapitre)
1 Appuyez sur c ou d.
Sélection dun album
1 Appuyez sur 1/
ou 2/ .
Avance ou retour rapide
1 Appuyez de manière prolongée sur c ou d.
Remarques
! LiPod ne peut pas être mis en service ou
hors service lorsque le mode de commande
est réglé sur CTRL AUDIO.
! Débranchez les écouteurs de liPod avant de
le connecter à cet appareil.
! LiPod sera mis hors service environ deux mi-
nutes après que le contact dallumage est
coupé.
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! TRACK INFO (titre de la plage/nom de lin-
terprète/nom de lalbum)
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
Recherche dune plage musicale
1 Appuyez sur pour passer au menu
principal de la recherche par liste.
Utilisation de cet appareil
22
Section
Utilisation de cet appareil
Fr
02
Black plate (23,1)
2 Utilisez M.C. pour sélectionner une caté-
gorie/plage musicale.
Modification du nom dune plage musicale/caté-
gorie
1 Tournez M.C.
Listes de lectureinterprètesalbumspla-
ges musicalespodcastsgenrescomposi-
teurslivres audio
Lecture
1 Quand une plage musicale est sélectionnée,
appuyez sur M.C.
Affichage dune liste des plages musicales dans
la catégorie sélectionnée
1 Quand une catégorie est sélectionnée, ap-
puyez sur M.C.
Lecture dune plage musicale dans la catégorie
sélectionnée
1 Quand une catégorie est sélectionnée, ap-
puyez sur M.C. de façon prolongée.
Recherche par ordre alphabétique dans la liste
1 Lorsque la liste de la catégorie sélectionnée
saffiche, appuyez sur
pour activer le mode
de recherche par ordre alphabétique.
! Vous pouvez également passer en mode
de recherche par ordre alphabétique en
tournant M.C. deux fois.
2 Tournez M.C. pour sélectionner une lettre.
3 Appuyez sur M.C. pour afficher la liste alpha-
bétique.
! Pour annuler la recherche, appuyez sur
/DIMMER.
Remarques
! Vous pouvez lire les listes de lecture créées à
laide de lapplication de lordinateur
(MusicSphere). Lapplication sera disponible
sur notre site web.
! Les listes de lecture créées à laide de lappli-
cation de lordinateur (MusicSphere) sont af-
fichées sous forme abrégée.
Opérations à laide de touches
spéciales
Sélection dune étendue de répétition de lecture
1 Appuyez sur 6/
pour parcourir les options
disponibles :
! ONE Répétition de la plage musicale en
cours de lecture
! ALL Répétition de toutes les plages musi-
cales de la liste sélectionnée
! Lorsque le mode de commande est défini sur
CTRL iPod,létendue de répétition de lecture
reste identique à celle définie pour liPod
connecté.
Sélection dune plage de lecture aléatoire (shuffle)
1 Appuyez sur 5/
pour parcourir les options
disponibles :
! SNG Lecture des plages musicales dans
un ordre aléatoire à lintérieur de la liste sé-
lectionnée.
! ALB Lecture dans lordre de plages musi-
cales à partir dun album sélectionné au
hasard.
! OFF Pas de lecture dans un ordre aléa-
toire.
Lecture de toutes les plages musicales dans un
ordre aléatoire (lecture aléatoire de toutes les pla-
ges)
1 Appuyez de façon prolongée sur 5/
pour
mettre en service la fonction de lecture aléa-
toire de toutes les plages.
! Pour mettre hors service la lecture aléatoire de
toutes les plages, sélectionnez OFF pour la lec-
ture aléatoire. Pour les détails, reportez-vous à
la page 23, Sélection dune plage de lecture
aléatoire (shuffle).
Pause de la lecture
1 Appuyez sur 4/PAUSE pour mettre en pause
ou reprendre la lecture.
Amélioration de laudio compressé et restauration
dun son riche (sound retriever (correcteur de son
compressé))
1 Appuyez sur 3/S.Rtrv pour parcourir les op-
tions disponibles :
12OFF (hors service)
1 est efficace pour les faibles taux de compres-
sion et 2 est efficace pour les taux de compres-
sion élevés.
Lecture de plages musicales
liées à la plage musicale en
cours de lecture
Vous pouvez lire des plages musicales dans les
listes suivantes.
Liste dalbums de linterprète en cours de lec-
ture
Liste de plages musicales de lalbum en cours
de lecture
Liste dalbums du genre en cours de lecture
1 Appuyez de façon prolongée sur
pour
activer le mode de lecture en liaison.
2 Tournez M.C. pour changer le mode, ap-
puyez pour sélectionner.
! ARTIST Lit un album de linterprète en
cours de lecture.
! ALBUM Lit une plage musicale de lalbum
en cours de lecture.
! GENRE Lit un album du genre en cours de
lecture.
La plage musicale/lalbum sélectionné sera lu
après la lecture de la plage musicale en cours.
Remarques
! La plage musicale/lalbum sélectionné peut
être annulé si vous utilisez dautres fonctions
que la fonction de recherche de liaison (re-
tour rapide et avance rapide, par exemple).
! En fonction de la plage musicale sélection-
née pour la lecture, la fin de la plage en
cours de lecture et le début de la plage musi-
cale/de lalbum sélectionné peuvent être
tronqués.
Utilisation de la fonction iPod
de cet appareil sur votre iPod
La fonction iPod de cet appareil peut être contrô-
lée à laide de liPod connecté.
CTRL iPod nest pas compatible avec les modè-
les diPod suivants.
! iPod nano 1ère génération
! iPod avec vidéo
% Appuyez sur BAND/
pour changer le
mode de commande.
! CTRL iPod La fonction iPod de cet appareil
peut être utilisée à partir de liPod connecté.
! CTRL AUDIO La fonction iPod de cet appa-
reil peut être contrôlée à laide de cet appa-
reil.
Vous pouvez également changer le mode de
commande en appuyant sur iPod.
Remarques
! Régler le mode de commande sur CTRL iPod
met en pause la lecture dune plage musi-
cale. Utilisez liPod pour reprendre la lecture.
! Les opérations suivantes sont toujours ac-
cessibles à partir de lappareil même si le
mode de commande est réglé sur
CTRL iPod.
Pause
Avance/retour rapide
Sélection dune plage musicale (dun chapi-
tre)
Français
Utilisation de cet appareil
23
Section
Utilisation de cet appareil
Fr
02
Black plate (24,1)
! Le volume ne peut être réglé quà partir de
cet appareil.
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
3 Tournez M.C. pour sélectionner la fonc-
tion.
Une fois sélectionnées, les fonctions suivantes
peuvent être ajustées.
! AUDIO BOOK nest pas disponible lorsque
CTRL iPod est sélectionné en mode de
commande. Pour les détails, reportez-vous à
la page 23, Utilisation de la fonction iPod de
cet appareil sur votre iPod.
AUDIO BOOK (vitesse du livre audio)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour choisir le réglage désiré.
! FASTER Lecture plus rapide que la vi-
tesse normale
! NORMAL Lecture à la vitesse normale
! SLOWER Lecture plus lente que la vitesse
normale
S.RTRV (sound retriever)
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
Pour les détails, reportez-vous à la page 23,
Amélioration de laudio compressé et restaura-
tion dun son riche (sound retriever (correcteur
de son compressé)).
Utilisation des applications
de lappareil connecté
Vous pouvez utiliser cet appareil pour la lecture
en continu et le contrôle de plages dapplica-
tions iPhone ou simplement pour la lecture en
continu.
Important
Lutilisation dapplications tierces peut impli-
quer ou nécessiter la fourniture dinforma-
tions personnelles, que ce soit en créant un
compte dutilisateur ou une autre méthode
ainsi que, pour certaines applications, la four-
niture de données de géolocalisation.
TOUTES LES APPLICATIONS TIERCES RELÈ-
VENT DE LENTIÈRE RESPONSABILITÉ DES
FOURNISSEURS, NOTAMMENT MAIS SANS
SY LIMITER, LA COLLECTE ET LA PROTEC-
TION DES DONNÉES UTILISATEUR ET LES
BONNES PRATIQUES DE CONFIDENTIALITÉ.
EN ACCÉDANT À UNE APPLICATION TIERCE,
VOUS ACCEPTEZ DE PRENDRE CONNAIS-
SANCE DES CONDITIONS DE SERVICE ET
DES RÈGLES DE CONFIDENTIALITÉ DES
FOURNISSEURS. SI VOUS NACCEPTEZ PAS
LES CONDITIONS OU RÈGLES DUN FOUR-
NISSEUR OU SI VOUS NACCEPTEZ PAS LU-
TILISATION DES DONNÉES DE
GÉOLOCALISATION, LE CAS ÉCHÉANT, NU-
TILISEZ PAS CETTE APPLICATION TIERCE.
Informations relatives à la
compatibilité des appareils
connectés
Vous trouverez ci-dessous les informations dé-
taillées relatives aux bornes nécessaires pour
utiliser lapplication pour iPhone sur cet appa-
reil.
Pour les utilisateurs diPhone
! Cette fonction est compatible avec iPhone et
iPod touch.
! iOS 5.0 ou supérieure est installé sur lappa-
reil.
Remarques
! Veuillez consulter notre site Web pour obte-
nir la liste des applications iPhone prises en
charge pour cet appareil.
! Pioneer ne pourra être tenu responsable des
problèmes résultant dun contenu incorrect
ou reposant sur une mauvaise application.
! Le contenu et les fonctionnalités des applica-
tions prises en charge sont de la responsabi-
lité des fournisseurs de lapplication.
Procédure de démarrage des
utilisateurs dun iPhone
1 Connectez un iPhone à lentrée USB.
2 Basculez la source sur APP.
3 Démarrez lapplication sur liPhone et
lancez la lecture.
Opérations de base
Sélection dune plage
1 Appuyez sur c ou d.
Avance ou retour rapide
1 Appuyez de manière prolongée sur c ou d.
Pause de la lecture
1 Appuyez sur BAND/
pour mettre en pause
ou reprendre la lecture.
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! TRACK INFO (titre de la plage/nom de lin-
terprète/nom de lalbum)
! APP NAME (nom de lapplication)
! ELAPSED TIME (temps de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
3 Tournez M.C. pour sélectionner la fonc-
tion.
Une fois sélectionnées, les fonctions suivantes
peuvent être ajustées.
PAUSE (pause)
1 Appuyez sur M.C. pour mettre en pause ou re-
prendre la lecture.
S.RTRV (sound retriever)
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
12OFF (hors service)
1 est efficace pour les faibles taux de compres-
sion et 2 est efficace pour les taux de compres-
sion élevés.
Utilisation de cet appareil
24
Section
Utilisation de cet appareil
Fr
02
Black plate (25,1)
Réglages sonores
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner AUDIO.
3 Tournez M.C. pour sélectionner la fonc-
tion audio.
Une fois sélectionnées, les fonctions audio sui-
vantes peuvent être ajustées.
! FADER nest pas disponible lorsque
SUB.W/SUB.W est sélectionné dans
SP-P/O MODE. Pour les détails, reportez-vous
à la page 26, SP-P/O MODE (réglage de la sor-
tie arrière et du préamp).
! SUB.W et SUB.W CTRL ne sont pas disponi-
bles lorsque REAR/REAR est sélectionné
dans SP-P/O MODE. Pour les détails, repor-
tez-vous à la page 26, SP-P/O MODE (réglage
de la sortie arrière et du préamp).
! SUB.W CTRL nest pas disponible lorsque
SUB.W est sélectionné dans OFF. Pour les
détails, reportez-vous à la page 25, SUB.W (ré-
glage en service/hors service du haut-parleur
dextrêmes graves).
! SLA nest pas disponible lorsque FM est sé-
lectionné comme source.
FADER (réglage de léquilibre avant-arrière)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler léquilibre sonore
entre les haut-parleurs avant et arrière.
BALANCE (réglage déquilibre sonore)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler léquilibre sonore
entre les haut-parleurs gauche/droite.
EQ SETTING (rappel de légaliseur)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner légaliseur.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
La bande et le niveau de légalisateur peuvent
être personnalisés lorsque CUSTOM1 ou CUS-
TOM2 est sélectionné.
Si CUSTOM1 ou CUSTOM2 est sélectionné,
suivez les procédures décrites ci-dessous. Si
dautres options sont sélectionnées, appuyez
sur M.C. pour revenir à laffichage précédent.
! CUSTOM1 peut être défini séparément
pour chaque source. Cependant, USB,
iPod et APP sont définis automatiquement
sur le même réglage.
! CUSTOM2 est un réglage partagé et
commun à toutes les sources.
3 Appuyez sur M.C. pour afficher le mode de ré-
glage.
4 Appuyez sur M.C. pour parcourir les options
disponibles :
Bande de légaliseurNiveau de légaliseur
5 Tournez M.C. pour sélectionner le réglage sou-
haité.
Bande de légaliseur : 80HZ250HZ800HZ
2.5KHZ8KHZ
Niveau de légaliseur : +6 à 6
LOUDNESS (correction physiologique)
La correction physiologique a pour objet daccen-
tuer les hautes et les basses fréquences à bas ni-
veaux découte.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
OFF (hors service)LOW (faible)MID
(moyen)HI (élevé)
SUB.W (réglage en service/hors service du haut-
parleur dextrêmes graves)
Cet appareil est équipé dune sortie haut-parleur
dextrêmes graves qui peut être mise en service
ou hors service.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
NOR (phase normale) REV (phase inversée)
OFF (haut-parleur dextrêmes graves désac-
tivé)
SUB.W CTRL (réglage du haut-parleur dextrêmes
graves)
Seules les fréquences inférieures à celles de la
plage sélectionnée sont produites par le haut-par-
leur dextrêmes graves.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour parcourir les options
disponibles :
Fréquence de coupureNiveau de sortieNi-
veau de pente
Les débits pouvant être réglés clignotent.
3 Tournez M.C. pour sélectionner le réglage sou-
haité.
Fréquence de coupure : 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Niveau de sortie : 24 à +6
Niveau de pente : 12 24
BASS BOOST (accentuation des graves)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le niveau dé-
siré.
0 à +6 sont les valeurs affichées tandis que le
niveau augmente ou diminue.
HPF SETTING (réglage du filtre passe-haut)
Utilisez cette fonction lorsque vous souhaitez uni-
quement écouter des sons aigus. Seules les fré-
quences supérieures à la coupure du filtre passe-
haut (HPF) sont émises en sortie via les haut-par-
leurs.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour parcourir les options
disponibles :
Fréquence de coupureNiveau de pente
3 Tournez M.C. pour sélectionner le réglage sou-
haité.
Fréquence de coupure : OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Niveau de pente : 12 24
SLA (réglage du niveau de la source)
Cette fonction empêche une modification trop im-
portante du volume lors du basculement de
source.
! Les réglages sont basés sur le niveau du vo-
lume FM qui lui, demeure inchangé.
! Le niveau du volume MW/LW (PO/GO) peut
également être réglé avec cette fonction.
! USB, iPod et APP sont définis automatique-
ment sur le même réglage.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler le volume de la
source.
Plage de réglage : +4 à 4
Français
Utilisation de cet appareil
25
Section
Utilisation de cet appareil
Fr
02
Black plate (26,1)
Menu système
Important
La fonction PW SAVE (économie dénergie) est
annulée si la batterie du véhicule est déconnec-
tée et devra être réactivée une fois la batterie re-
connectée. Quand PW SAVE est hors service, il
est possible que selon la méthode de connexion
utilisée lappareil continue à consommer du
courant de la batterie si le commutateur de
contact de votre véhicule ne possède pas de po-
sition ACC (accessoire).
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
3 Tournez M.C. pour sélectionner la fonc-
tion du menu système.
Une fois sélectionnées, les fonctions du menu
système suivantes peuvent être ajustées.
LANGUAGE (multilingue)
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
ENG (Anglais)РУС (Russe)TUR (Turc)
CLOCK SET (réglage de lhorloge)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour sélectionner le seg-
ment de laffichage de lhorloge que vous sou-
haitez régler.
HeureMinute
3 Tournez M.C. pour régler lhorloge.
12H/24H (notation temporelle)
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
12H (horloge 12 heures)24H (horloge
24 heures)
AUTO PI (recherche automatique PI)
Lappareil peut rechercher automatiquement une
autre station avec le même type de programme, y
compris si laccord a été obtenu par le rappel
dune fréquence en mémoire.
1 Appuyez sur M.C. pour mettre en service ou
hors service la recherche automatique PI.
AUX (entrée auxiliaire)
Activez ce réglage lorsque vous utilisez un appa-
reil auxiliaire connecté à cet appareil.
1 Appuyez sur M.C. pour mettre AUX en service
ou hors service.
DIMMER (atténuateur de luminosité)
1 Appuyez sur M.C. pour mettre latténuateur de
luminosité en service ou hors service.
! Vous pouvez également changer le réglage de
latténuateur de luminosité en appuyant de
façon prolongée sur
/DIMMER.
MUTE MODE (mode sourdine)
Le son émis par lappareil est automatiquement
coupé ou atténué quand un signal en provenance
dun équipement possédant la fonction silencieux
est reçu.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le réglage sou-
haité.
! MUTE Silencieux
! 20dB ATT Atténuation (20dB ATT aun
effet plus fort que 10dB ATT)
! 10dB ATT Atténuation
PW SAVE (économie dénergie)
Activer cette fonction vous permet de réduire la
consommation de la batterie.
! La mise en service de la source est la seule
opération permise quand cette fonction est en
service.
1 Appuyez sur M.C. pour mettre léconomie dé-
nergie en service ou hors service.
Menu initial
1 Maintenez la pression sur SRC/OFF jus-
quà ce que lappareil soit mis hors tension.
2 Appuyez de façon prolongée sur SRC/
OFF jusquà ce que le menu principal appa-
raisse sur lafficheur.
3 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner INITIAL.
4 Tournez M.C. pour sélectionner la fonc-
tion du menu initial.
Une fois sélectionnées, les fonctions du menu
initial suivantes peuvent être ajustées.
FM STEP (incrément daccord FM)
1 Appuyez sur M.C. pour choisir lincrément
daccord FM.
100 (100 kHz) 50 (50 kHz)
SP-P/O MODE (réglage de la sortie arrière et du
préamp)
La sortie des bornes du haut-parleur arrière et la
sortie RCA de cet appareil peuvent être utilisées
pour connecter un haut-parleur pleine gamme ou
un haut-parleur dextrêmes graves. Sélectionnez
loption appropriée à votre connexion.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le réglage sou-
haité.
! REAR/SUB.W Sélectionnez cette option
lorsquun haut-parleur pleine gamme est
connecté aux bornes du haut-parleur ar-
rière et quun haut-parleur dextrêmes gra-
ves est connecté à la sortie RCA.
! SUB.W/SUB.W Sélectionnez cette option
lorsquun haut-parleur dextrêmes graves
est connecté directement aux bornes du
haut-parleur arrière sans amplificateur au-
xiliaire et quun haut-parleur dextrêmes
graves est connecté à la sortie RCA.
! REAR/REAR Sélectionnez cette option
lorsquun haut-parleur pleine gamme est
connecté aux bornes du haut-parleur ar-
rière et à la sortie RCA.
Si un haut-parleur pleine gamme est
connecté à la sortie des bornes du haut-
parleur arrière et que la sortie RCA nest
pas utilisée, vous pouvez sélectionner
REAR/SUB.W ou REAR/REAR.
Menu système
1 Maintenez la pression sur SRC/OFF jus-
quà ce que lappareil soit mis hors tension.
2 Appuyez de façon prolongée sur SRC/
OFF jusquà ce que le menu principal appa-
raisse sur lafficheur.
Utilisation de cet appareil
26
Section
Utilisation de cet appareil
Fr
02
Black plate (27,1)
3 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
4 Tournez M.C. pour sélectionner la fonc-
tion du menu système.
Pour les détails, reportez-vous à la page 26,
Menu système.
Utilisation dune source AUX
1 Insérez la mini prise stéréo dans le jack
dentrée AUX.
2 Appuyez sur SRC/OFF pour choisir AUX
comme source.
Remarque
Vous ne pouvez pas sélectionner AUX à moins
que le réglage auxiliaire soit activé. Pour plus de
détails, reportez-vous à la page 26, AUX (entrée
auxiliaire).
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! Nom de la source
! Nom de la source et horloge
Si un écran non souhaité
saffiche
Mettez lécran non souhaité hors ser vice à laide
des procédures répertoriées ci-dessous.
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
3 Tournez M.C. pour afficher DEMO OFF,
puis appuyez pour sélectionner.
4 Tournez M.C. pour passer à YES.
5 Appuyez sur M.C. pour sélectionner.
Connexions
Important
! Lors de linstallation de cet appareil dans un
véhicule sans position ACC (accessoire) sur
le contact dallumage, ne pas connecter le
câble rouge à la borne qui détecte lutilisa-
tion de la clé de contact peut entraîner le dé-
chargement de la batterie.
O
N
S
T
A
R
T
O
F
F
Avec position ACC Sans position ACC
! Lutilisation de cet appareil dans des condi-
tions autres que les conditions suivantes
pourrait provoquer un incendie ou un mau-
vais fonctionnement.
Véhicules avec une batterie 12 volts et mise à
la masse du négatif.
Haut-parleurs avec une puissance de sortie
de 50 W et une impédance de 4 W à8W.
! Pour éviter un court-circuit, une surchauffe
ou un dysfonctionnement, assurez-vous de
respecter les instructions suivantes.
Déconnectez la borne négative de la batterie
avant linstallation.
Fixez le câblage avec des serre-fils ou de la
bande adhésive. Pour protéger le câblage, en-
roulez dans du ruban adhésif les parties du
câblage en contact avec des pièces en métal.
Placez les câbles à lécart de toutes les par-
ties mobiles, telles que le levier de vitesse et
les rails des sièges.
Placez les câbles à lécart de tous les endroits
chauds, par exemple les sorties de chauf-
fage.
Ne reliez pas le câble jaune à la batterie à tra-
vers le trou dans le compartiment moteur.
Recouvrez tous les connecteurs de câbles qui
ne sont pas connectés avec du ruban adhésif
isolant.
Ne raccourcissez pas les câbles.
Ne coupez jamais lisolation du câble dali-
mentation de cet appareil pour partager lali-
mentation avec dautres appareils. La
capacité en courant du câble est limitée.
Utilisez un fusible correspondant aux caracté-
ristiques spécifiées.
Ne câblez jamais le câble négatif du haut-par-
leur directement à la masse.
Ne réunissez jamais ensemble les câbles né-
gatifs de plusieurs haut-parleurs.
! Lorsque cet appareil est sous tension, les si-
gnaux de commande sont transmis via le
câble bleu/blanc. Connectez ce câble à la té-
lécommande du système dun amplificateur
de puissance externe ou à la borne de
commande du relais de lantenne motorisée
du véhicule (max. 300 mA 12 V CC). Si le véhi-
cule est équipé dune antenne intégrée à la
lunette arrière, connectez-le à la borne dali-
mentation de lamplificateur dantenne.
! Ne reliez jamais le câble bleu/blanc à la
borne dalimentation dun amplificateur de
puissance externe. De même, ne le reliez pas
à la borne dalimentation de lantenne moto-
risée. Dans le cas contraire, il peut en résul-
ter un déchargement de la batterie ou un
dysfonctionnement.
! Le câble noir est la masse. Les câbles de
terre de cet appareil et dautres produits (par-
ticulièrement les produits avec des courants
élevés tels que lamplificateur de puissance)
doivent être câblés séparément. Dans le cas
contraire, ils peuvent se détacher accidentel-
lement et provoquer un incendie ou un dys-
fonctionnement.
Français
Utilisation de cet appareil
27
Section
Installation
Fr
02
03
Black plate (28,1)
Cet appareil
3
1 24
5
1 Entrée antenne
2 Fusible (10 A)
3 Entrée cordon dalimentation
4 Entrée télécommande câblée
Un adaptateur de télécommande câblée
(vendu séparément) peut être connecté.
5 Sortie arrière ou haut-parleur dextrêmes gra-
ves
Cordon dalimentation
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Vers lentrée cordon dalimentation
2 Selon le type de véhicule, 3 et 5 peuvent
avoir une fonction différente. Dans ce cas,
assurez-vous de connecter 4 à 5 et 6 à 3.
3 Jaune
Alimentation de secours (ou accessoire)
4 Jaune
Connectez à la borne dalimentation 12 V per-
manente.
5 Rouge
Accessoire (ou alimentation de secours)
6 Rouge
Connectez à la borne contrôlée par le
contact dallumage (12 V CC).
7 Connectez les fils de même couleur en-
semble.
8 Noir (masse du châssis)
9 Bleu/blanc
La position des broches du connecteur ISO
est différente selon le type de véhicule.
Connectez 9 et b lorsque la broche 5 est de
type commande de lantenne. Dans un type
différent de véhicule, ne connectez jamais 9
et b.
a Bleu/blanc
Connectez à la borne de commande du sys-
tème de lamplificateur de puissance (max.
300 mA 12 V CC).
b Bleu/blanc
Connectez à la borne de commande du relais
de lantenne motorisée (max. 300 mA 12 V
CC).
c Jaune/noir
Si vous utilisez un équipement avec la fonc-
tion Coupure du son, câblez ce fil au fil Cou-
pure Audio de cet équipement. Sinon, ne
connectez rien au fil Coupure Audio.
d Fils des haut-parleurs
Blanc : Avant gauche +
Blanc/noir : Avant gauche *
Gris : Avant droite +
Gris/noir : Avant droite *
Vert: Arrière gauche + ou haut-parleur dex-
trêmes graves +
Vert/noir: Arrière gauche * ou haut-parleur
dextrêmes graves *
Violet : Arrière droite + ou haut-parleur dex-
trêmes graves +
Violet/noir: Arrière droite * ou haut-parleur
dextrêmes graves *
e Connecteur ISO
Dans certains véhicules, il est possible que
le connecteur ISO soit divisé en deux. Dans
ce cas, assurez-vous de connecter les deux
connecteurs.
Remarques
! Changez le menu initial de cet appareil. Re-
portez-vous à la page 26, SP-P/O MODE (ré-
glage de la sortie arrière et du préamp).
La sortie haut-parleur dextrêmes graves de
cet appareil est monaurale.
! Lors de lutilisation dun haut-parleur dextrê-
mes graves de 70 W (2 W), assurez-vous de
connecter le haut-parleur dextrêmes graves
aux fils violet et violet/noir de cet appareil. Ne
connectez aucun périphérique aux fils vert et
vert/noir.
Amplificateur de puissance
(vendu séparément)
Réalisez ces connexions lors de lutilisation dun
amplificateur optionnel.
1
3
2
4
55
1 Télécommande du système
Connectez au câble bleu/blanc.
2 Amplificateur de puissance (vendu séparé-
ment)
3 Connectez avec des câbles RCA (vendus sé-
parément)
4 Vers la sortie arrière ou la sortie du haut-par-
leur dextrêmes graves
5 Haut-parleur arrière ou haut-parleur dextrê-
mes graves
Installation
Important
! Vérifiez toutes les connexions et tous les sys-
tèmes avant linstallation finale.
! Nutilisez pas de pièces non autorisées car il
peut en résulter des dysfonctionnements.
! Consultez votre revendeur si linstallation né-
cessite le perçage de trous ou dautres modi-
fications du véhicule.
! Ninstallez pas cet appareil :
il peut interférer avec lutilisation du véhicule.
il peut blesser un passager en cas darrêt
soudain du véhicule.
! Le laser à semi-conducteur sera endommagé
sil devient trop chaud. Installez cet appareil
àlécart de tous les endroits chauds, par
exemple les sorties de chauffage.
! Des performances optimales sont obtenues
quand lappareil est installé à un angle infé-
rieur à 60°.
60°
Installation
28
Section
Installation
Fr
03
Black plate (29,1)
! Lors de linstallation, pour assurer une dis-
persion correcte de la chaleur quand cet ap-
pareil est utilisé, assurez-vous de laisser un
espace important derrière la face arrière et
enroulez les câbles volants de façon quils ne
bloquent pas les orifices daération.
Laissez suffisamment
d’espace
5 cm
5 cm
! Utilisez des pièces disponibles dans le
commerce lors de linstallation.
Procédure dinstallation
Cet appareil peut être installé correctement
selon lune des méthodes de la liste ci-dessous.
! Installation avec le support
! Installation à laide des trous de vis sur les
côtés de lappareil
Avant linstallation de cet appareil
1 Retirez lanneau de garniture.
1
1 Anneau de garniture
2 Insérez les clés dextraction fournies dans
les deux côtés de lappareil jusquàcequel-
les senclenchent en place.
3 Tirez lappareil hors du support.
Retirez le support.
1
1 Support
(pièce fournie)
Installation avec le support
1 Installez le support dans le tableau de
bord.
Une fois le support installé dans le tableau de
bord, sélectionnez et courber les pattes en fonc-
tion de lépaisseur du tableau de bord. (Fixez cet
appareil aussi fermement que possible à laide
des pattes supérieures et inférieures. Afin de
fixer fermement lappareil, courbez les pattes de
90 degrés.)
1
2
1 Tableau de bord
2 Support
(pièce fournie)
2 Installez cet appareil.
1
1 Tableau de bord
3 Fixez lanneau de garniture.
1
1 Anneau de garniture
Retrait du support
La procédure est identique à la procédure Avant
linstallation de cet appareil. Pour les détails, re-
portez-vous à la page 29, Avant linstallation de
cet appareil.
Installation à l aide des trous de
vis sur les côtés de lappareil
% Fixation de lappareil sur le support de
montage radio dusine.
Positionnez lappareil de sorte que les trous des
vis soient alignés avec les trous des vis sur le
support, puis serrez les vis aux trois emplace-
ments de chaque côté de lappareil.
Français
Installation
29
Section
Installation
Fr
03
Black plate (30,1)
1
2
4
3
1 Courbez la languette vers le bas si elle gêne.
2 Support de montage radio dusine
3 Vis à tête bombée (5 mm × 8 mm)
4 Tableau de bord ou console
Dépannage
Les symptômes apparaissent en gras et les cau-
ses sous la forme de texte régulier non indenté.
Le texte régulier indenté est utilisé pour indiquer
les actions à mettre en œuvre.
Lécran revient automatiquement à laffichage
ordinaire.
Vous navez exécuté aucune opération pendant 30
secondes.
Réexécutez lopération.
Létendue de répétition de lecture change de ma-
nière inattendue.
En fonction de létendue de répétition de lecture, lé-
tendue sélectionnée peut changer lors de la sélec-
tion dun autre dossier ou dune autre plage ou
pendant lavance ou le retour rapide.
Resélectionnez létendue de répétition de lecture.
Un sous-dossier nest pas lu.
Il est impossible de lire les sous-dossiers lorsque
FLD (répétition du dossier) est sélectionné.
Sélectionnez une autre étendue de répétition de
lecture.
NO XXXX saffiche lors de la modification de laf-
fichage (par exemple NO TITLE).
Aucune information textuelle nest intégrée.
Basculez laffichage ou la lecture sur une autre
plage/un autre fichier.
Lappareil ne fonctionne pas correctement.
Il y a des interférences.
Vous utilisez un périphérique, un téléphone portable
par exemple, qui peut générer des interférences so-
nores.
Éloignez tous les appareils électriques qui
pourrait provoquer des interférences.
Messages derreur
Quand vous contactez votre distributeur ou le
Service dentretien agréé par Pioneer le plus
proche, noubliez pas de noter le message der-
reur.
Les message derreur apparaissent en gras et
les causes sous la forme de texte régulier non
indenté. Le texte régulier indenté est utilisé pour
indiquer les actions à mettre en œuvre.
Commun
AMP ERROR
Une anomalie de fonctionnement de lappareil sest
produite ou la connexion des haut-parleurs est incor-
recte. Le circuit de protection est activé.
Vérifiez la connexion des haut-parleurs. Si le
message ne disparaît pas même après avoir
éteint puis démarré le moteur, consultez votre
distributeur ou un centre dentretien agréé par
Pioneer.
Lecteur de CD
ERROR-07, 11, 12, 17, 30
Le disque est sale.
Nettoyez le disque.
Le disque est rayé.
Utilisez un autre disque.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Une erreur mécanique ou électrique est survenue.
Coupez et remettez le contact dallumage ou
choisissez une autre source, puis revenez au
lecteur de CD.
ERROR-15
Le disque inséré est vierge.
Utilisez un autre disque.
Installation
30
Section
Informations complémentaires
Fr
03
Black plate (31,1)
ERROR-23
Format CD non pris en charge.
Utilisez un autre disque.
FORMAT READ
Le début de la lecture et le début de lémission des
sons sont parfois décalés.
Attendez que le message disparaisse pour
entendre les sons.
NO AUDIO
Le disque inséré ne contient pas de fichiers pouvant
être lus.
Utilisez un autre disque.
SKIPPED
Le disque inséré contient des fichiers protégés par
DRM.
Les fichiers protégés sont sautés.
PROTECT
Tous les fichiers sur le disque inséré intègrent la pro-
tection par DRM.
Utilisez un autre disque.
Périphérique de stockage USB/iPod
FORMAT READ
Le début de la lecture et le début de lémission des
sons sont parfois décalés.
Attendez que le message disparaisse pour
entendre les sons.
NO AUDIO
Absence de plages musicales.
Transférez les fichiers audio vers le périphérique
de stockage USB et procédez à la connexion.
La sécurité est activée sur le périphérique de stoc-
kage USB.
Suivez les instructions du périphérique de
stockage USB pour désactiver la sécurité.
SKIPPED
Le périphérique de stockage USB connecté contient
des fichiers protégés par DRM.
Les fichiers protégés sont sautés.
PROTECT
Tous les fichiers sur le périphérique de stockage
USB connecté intègrent la protection par DRM.
Remplacez le périphérique de stockage USB.
N/A USB
Le périphérique USB connecté nest pas pris en
charge par cet appareil.
! Connectez un périphérique de stockage de
masse USB compatible.
! Déconnectez votre périphérique et remplacez-
le par un périphérique de stockage USB
compatible.
CHECK USB
Le connecteur USB ou le câble USB est en court-cir-
cuit.
Vérifiez que le connecteur USB ou le câble USB
nest pas coincé ou endommagé.
CHECK USB
Le périphérique de stockage USB connecté
consomme plus que le courant maximal autorisé.
Déconnectez le périphérique de stockage USB et
ne lutilisez pas. Mettez le contact sur OFF, puis
sur ACC ou ON, et ne connectez que des
périphériques de stockage USB compatibles.
CHECK USB
LiPod fonctionne correctement mais nest pas
chargé.
Assurez-vous que le câble de connexion de liPod
nest pas en court-circuit (par exemple, quil
nest pas coincé dans des objets métalliques).
Après avoir vérifié, mettez le contact dallumage
sur OFF puis sur ON, ou déconnectez liPod et
reconnectez-le.
ERROR-19
Panne de communication.
Effectuez une des opérations suivantes.
Coupez et remettez le contact dallumage.
Déconnectez le périphérique de stockage USB.
Choisissez une autre source.
Revenez ensuite à la source USB.
Panne iPod.
Déconnectez le câble de liPod. Quand le menu
principal de liPod est affiché, reconnectez et
réinitialisez liPod.
ERROR-23
Le périphérique de stockage USB na pas été for-
maté avec FAT12, FAT16 ou FAT32.
Le périphérique de stockage USB doit être
formaté avec FAT12, FAT16 ou FAT32.
ERROR-16
La version du firmware de liPod est ancienne.
Mettez à jour la version de liPod.
Panne iPod.
Déconnectez le câble de liPod. Quand le menu
principal de liPod est affiché, reconnectez et
réinitialisez liPod.
STOP
Aucune plage musicale dans la liste en cours.
Sélectionnez une liste qui contient les plages
musicales.
NOT FOUND
Aucune plage musicale connexe.
Transférez les plages musicales sur liPod.
Application
START UP APP
Lapplication na pas encore démarré.
Suivez les instructions qui saffichent à lécran.
Conseils sur la manipulation
Disques et lecteur
Utilisez uniquement des disques affichant lun ou
lautre des logos suivants.
Utilisez des disques 12 cm.
Utilisez seulement des disques conventionnels de
forme circulaire.
Les types de disques suivants ne peuvent pas être
utilisés avec cet appareil.
! DualDiscs
! Disques 8 cm : Les tentatives dutilisation de
tels disques avec un adaptateur peuvent en-
traîner un dysfonctionnement de lappareil.
! Disques de forme bizarre
! Disques autres que les CD
! Disques endommagés, y compris les disques
fendillés, ébréchés ou voilés
! Disques CD-R/RW non finalisés
Français
Informations complémentaires
31
Annexe
Informations complémentaires
Fr
Black plate (32,1)
Ne touchez pas la surface enregistrée des dis-
ques.
Rangez les disques dans leur coffret dès que vous
ne les écoutez plus.
Ne posez aucune étiquette sur la surface des dis-
ques, nécrivez pas sur un disque, nappliquez
aucun agent chimique sur un disque.
Pour nettoyer un CD, essuyez le disque avec un
chiffon doux en partant du centre vers lextérieur.
La condensation peut perturber temporairement
le fonctionnement du lecteur. Laissez celui-ci sa-
dapter à la température plus élevée pendant une
heure environ. Essuyez également les disques hu-
mides avec un chiffon doux.
La lecture de certains disques peut être impos-
sible en raison des caractéristiques du disque, de
son format, de lapplication qui la enregistré, de
lenvironnement de lecture, des conditions de
stockage ou dautres conditions.
Les cahots de la route peuvent interrompre la lec-
ture dun disque.
Lors de lutilisation de disques dont la surface de
létiquette est imprimable, vérifiez les instructions
et les avertissements des disques. Linsertion et
léjection peuvent ne pas être possibles selon les
disques. Lutilisation dun tel disque risque den-
dommager cet appareil.
Ne posez aucune étiquette disponible dans le
commerce ou tout autre matériau sur la surface
des disques.
! Les disques pourraient se déformer et devenir
injouables.
! Les étiquettes pourraient se décoller pendant
la lecture et empêcher léjection des disques,
ce qui pourrait endommager lappareil.
Périphérique de stockage USB
Les connexions via un concentrateur USB ne sont
pas prises en charge.
Ne connectez aucun périphérique autre quun pé-
riphérique de stockage USB.
Fixez fermement le périphérique de stockage USB
lors de la conduite. Ne laissez pas le périphérique
de stockage USB tomber sur le plancher, il
pourrait gêner le bon fonctionnement de la pédale
de frein ou daccélérateur.
En fonction du périphérique de stockage USB, les
problèmes suivants peuvent survenir.
! Le fonctionnement peut varier.
! Le périphérique de stockage peut ne pas être
reconnu.
! Les fichiers peuvent ne pas être lus correcte-
ment.
! Le périphérique peut générer des interférences
sonores lorsque vous écoutez la radio.
iPod
Ne laissez pas liPod dans un endroit soumis à
une température élevée.
Attachez fermement liPod pendant que vous
conduisez. Ne laissez pas liPod tomber sur le
plancher, il pourrait gêner le bon fonctionne-
ment de la pédale de frein ou daccélérateur.
Quelques mots sur les réglages de liPod
! Lorsquun iPod est connecté, cet appareil dés-
active le réglage EQ (égaliseur) de liPod afin
doptimiser lacoustique. Le réglage EQ origi-
nal est rétabli lorsque liPod est déconnecté.
! Vous ne pouvez pas mettre la fonction de répé-
tition hors service sur liPod quand vous utili-
sez cet appareil. La fonction de répétition est
positionnée automatiquement sur répétition
de toutes les plages quand vous connectez
liPod à cet appareil.
Tout texte incompatible enregistré sur liPod ne
sera pas affiché par cet appareil.
Formats audio compressés
compatibles (disque, USB)
WMA
Extension de fichier : .wma
Débit binaire : 48 kbit/s à 320 kbit/s (CBR), 48 kbit/s
à 384 kbit/s (VBR)
Fréquence déchantillonnage : 32 kHz, 44,1 kHz,
48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream avec vidéo : incompa-
tible
MP3
Extension de fichier : .mp3
Débit binaire : 8 kbit/s à 320 kbit/s (CBR), VBR
Fréquence déchantillonnage : 8 kHz à 48 kHz
(32 kHz, 44,1 kHz, 48 kHz pour accentuation)
Version étiquette ID3 compatible : 1.0, 1.1, 2.2, 2.3,
2.4 (la Version 2.x de létiquette ID3 a priorité sur la
Version 1.x.)
Liste de lecture m3u : incompatible
MP3i (MP3 interactif), mp3 PRO : incompatible
WAV
Extension de fichier : .wav
Bits de quantification : 8 et 16 (LPCM), 4 (MS
ADPCM)
Fréquence déchantillonnage : 16 kHz à 48 kHz
(LPCM), 22,05 kHz et 44,1 kHz (MS ADPCM)
! Vous ne pouvez pas utiliser cette fonction
avec USB MTP.
Informations supplémentaires
Seuls les 32 premiers caractères dun nom de fi-
chier (incluant lextension de fichier) ou dun nom
de dossier peuvent être affichés.
Les textes russes à afficher sur cet appareil doi-
vent être codés avec un des jeux de caractères sui-
vants :
! Unicode (UTF-8, UTF-16)
! Un jeu de caractères autre que Unicode qui
est utilisé dans un environnement Windows et
qui est paramétré sur Russe dans le réglage
multilingue
Cet appareil peut ne pas fonctionner correctement
selon lapplication utilisée pour encoder les fi-
chiers WMA.
Il peut se produire un léger retard au début de la
lecture de fichiers audio intégrés avec des don-
nées image ou de fichiers audio stockés sur un pé-
riphérique de stockage USB avec de nombreuses
hiérarchies de dossiers.
Informations complémentaires
32
Annexe
Informations complémentaires
Fr
Black plate (33,1)
Disque
Hiérarchie des dossiers pouvant être lus : jusquà
8 niveaux (dans la pratique, la hiérarchie compte
moins de 2 niveaux).
Dossiers pouvant être lus : jusquà99
Fichiers pouvant être lus : jusquà 999
Système de fichiers : ISO 9660 Niveau 1 et 2,
Romeo, Joliet
Lecture multi-session : compatible
Transfert des données en écriture par paquet : in-
compatible
Quelle que soit la durée du silence entre les pla-
ges musicales de lenregistrement original, la lec-
ture des disques daudio compressé seffectue
avec une courte pause entre les plages musicales.
Périphérique de stockage USB
Hiérarchie des dossiers pouvant être lus : jusquà
8 niveaux (dans la pratique, la hiérarchie compte
moins de 2 niveaux).
Dossiers pouvant être lus : jusquà 500
Fichiers pouvant être lus : jusquà 15 000
Lecture des fichiers protégés par des droits dau-
teur : incompatible
Périphérique de stockage USB partitionné : Seule
la première partition peut être lue.
Il peut se produire un léger retard au début de la
lecture de fichiers audio sur un périphérique de
stockage USB avec de nombreuses hiérarchies de
dossiers.
PRÉCAUTION
! Pioneer ne garantit pas la compatibilité avec
tous les périphériques de stockage de masse
USB et décline toute responsabilité en cas
de perte de données sur des lecteurs multi-
média, smartphones ou autres périphériques
lors de lutilisation de ce produit.
! Ne laissez pas de disques ou un périphérique
de stockage USB dans un lieu les tempé-
ratures sont élevées.
Compatibilité iPod
Cet appareil prend en charge uniquement les
modèles diPod suivants.
Conçu pour
! iPod touch (5ème génération)
! iPod touch (4ème génération)
! iPod touch (3ème génération)
! iPod touch (2ème génération)
! iPod touch (1ère génération)
! iPod classic
! iPod avec vidéo
! iPod nano (7ème génération)
! iPod nano (6ème génération)
! iPod nano (5ème génération)
! iPod nano (4ème génération)
! iPod nano (3ème génération)
! iPod nano (2ème génération)
! iPod nano (1ère génération)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Selon la génération ou la version de liPod, certai-
nes fonctions peuvent ne pas être disponibles.
Les opérations peuvent différer selon la version du
logiciel iPod.
Les utilisateurs dun iPod avec connecteur Lightn-
ing doivent utiliser le câble Lightning vers USB
(fourni avec liPod).
Les utilisateurs dun iPod avec Dock Connector
doivent utiliser le CD-IU51. Pour plus de détails,
consultez votre revendeur.
Pour des détails sur la compatibilité fichier/format,
reportez-vous aux manuels de liPod.
Livre audio, podcast : compatible
PRÉCAUTION
Pioneer naccepte aucune responsabilité en cas
de perte de données sur liPod, même si la perte
de données se produit pendant lutilisation de
cet appareil.
Séquence des fichiers audio
Sur cet appareil, lutilisateur ne peut pas affecter
de numéros de dossier ni spécifier les séquen-
ces de lecture.
Exemple de hiérarchie
1
2
3
4
5
6
01
02
03
04
05
Niveau 1 Niveau 2 Niveau 3 Niveau 4
: Dossier
: Fichier daudio
compressé
01 à 05 : Numéro de
dossier
1 à 6 : Séquence
de lecture
Disque
La séquence de sélection des dossiers ou dau-
tres opérations peut différer en fonction du logi-
ciel de codage ou décriture.
Périphérique de stockage USB
La séquence de lecture est identique à la sé-
quence enregistrée dans le périphérique de
stockage USB.
Pour spécifier la séquence de lecture, la mé-
thode suivante est recommandée.
1 Créez un nom de fichier en incluant des
nombres qui spécifient la séquence de lec-
ture (par exemple, 001xxx.mp3 et
099yyy.mp3).
2 Placez ces fichiers dans un dossier.
3 Enregistrez le dossier contenant les fichiers
sur le périphérique de stockage USB.
Toutefois, avec certains environnements sys-
tème, vous ne pouvez pas spécifier la séquence
de lecture.
Pour les lecteurs audio portables USB, la sé-
quence est différente et dépend du lecteur.
Tableau des caractères
cyrilliques
D:C D:C D:C D:C D:C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D : Affichage C : Caractère
Français
Informations complémentaires
33
Annexe
Informations complémentaires
Fr
Black plate (34,1)
Droits dauteur et marques
commerciales
MP3
La vente de ce produit comporte seulement une
licence dutilisation privée, non commerciale, et
ne comporte pas de licence ni nimplique aucun
droit dutilisation de ce produit pour une diffu-
sion commerciale (cest-à-dire générant des re-
venus) en temps réel (terrestre, par satellite,
câble et/ou tout autre média), diffusion/stream-
ing via internet, des intranets et/ou dautres sys-
tèmes électroniques de distribution de contenu,
telles que les applications audio payante ou
audio à la demande. Une licence indépendante
est requise pour de telles utilisations. Pour les
détails, veuillez visiter le site
http://www.mp3licensing.com.
WMA
Windows Media est une marque déposée ou
une marque commerciale de Microsoft
Corporation aux États-Unis et/ou dans dautres
pays.
Ce produit intègre une technologie détenue par
Microsoft Corporation, qui ne peut être utilisée
et distribuée que sous licence de Microsoft
Licensing, Inc.
iPod et iPhone
iPhone, iPod, iPod classic, iPod nano et iPod
touch sont des marques commerciales
dApple Inc., déposées aux États-Unis et dans
dautres pays.
Lightning est une marque commerciale
dApple Inc.
Les accessoires électroniques portant la men-
tion « Made for iPod » et « Made for iPhone »
ont été conçus pour fonctionner respectivement
avec un iPod ou un iPhone et sont certifiés
conformes aux exigences dApple par le fabri-
cant. Apple nest pas responsable pour le fonc-
tionnement de cet appareil ou de sa
compatibilité avec les normes réglementaires et
de sécurité. Veuillez noter que lemploi de cet
accessoire avec un iPod ou un iPhone peut af-
fecter les performances sans fil.
Androidä
Android est une marque commerciale de
Google Inc.
Caractéristiques techniques
Généralités
Tension dalim entation ..... 14,4 V CC (10,8 V à 15,1 V ac-
ceptable)
Mise à la masse ............... Pôle négatif
Consommation maximale
................................... 10,0 A
Dimensions (L × H × P) :
DIN
Châssis ............................ 178mm × 100mm × 157 mm
Panneau avant ................. 188mm × 118mm × 25mm
D
Châssis ............................ 178mm × 100mm × 165 mm
Panneau avant ................. 170mm × 96mm × 17mm
Poids ............................... 1,2 kg
Audio
Puissance de sortie maximale
................................... 50 W × 4
70 W × 1/2 W (pour le haut-
parleur dextrêmes graves)
Puissance de sortie continue
................................... 22W × 4 (50Hz à 15000Hz,
THD 5 %, impédance de
charge 4 W, avec les deux ca-
naux entraînés)
Impédance de charge ...... 4 W (4 W à8W acceptable)
Niveau de sortie maximum de la sortie préamp
................................... 2,0V
Correction physiologique
................................... +10dB (100 Hz), +6,5 dB
(10 kHz) (volume : 30 dB)
Égaliseur (Égaliseur graphique à 5 bandes) :
Fréquence ........................ 80Hz/250 Hz/800 Hz/2,5 kHz/
8 kHz
Plage dégalisation .......... ±12 dB (par pas de 2 dB)
Haut-parleur dextrême s graves (mono) :
Fréquence ........................ 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pente ............................... 12 dB/oct, 24 dB/oct
Gain ................................ +6dB à 24 dB
Phase .............................. Normale/Inverse
Lecteur de CD
Système ........................... Compact Disc Digital Audio
Disques utilisables ........... Disques compacts
Rapport signal/bruit ......... 94dB (1kHz) (réseau IEC-A)
Nombre de canaux ........... 2 (stéréo)
Format de décodage MP3
................................... MPEG-1 & 2 Couche Audio 3
Format de décodage WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ca-
naux audio)
(Windows Media Player)
Format du signal WAV ...... PCM Linéaire & MS ADPCM
(Non compressé)
USB
Spécification standard USB
................................... USB 2.0 vitesse pleine
Alimentation maximale .... 1A
Classe USB ...................... MSC (Mass Storage Class)
Système de fichiers .......... FAT12, FAT16, FAT32
Format de décodage MP3
................................... MPEG-1 & 2 Couche Audio 3
Format de décodage WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ca-
naux audio)
(Windows Media Player)
Format du signal WAV ...... PCM Linéaire & MS ADPCM
(Non compressé)
Syntoniseur FM
Gamme de fréquence ....... 87,5 MHz à 108,0 MHz
Sensibilité utile ................ 9dBf (0,8 µV/75 W, mono, S/B :
30 dB)
Rapport signal/bruit ......... 72dB (réseau IEC-A)
Syntoniseur MW (PO)
Gamme de fréquence ....... 531kHz à 1 602kHz
Sensibilité utile ................ 25µV (S/B : 20 dB)
Rapport signal/bruit ......... 62dB (réseau IEC-A)
Syntoniseur LW (GO)
Gamme de fréquence ....... 153kHz à 281 kHz
Sensibilité utile ................ 28µV (S/B : 20 dB)
Rapport signal/bruit ......... 62dB (réseau IEC-A)
Remarque
Les caractéristiques et la présentation peuvent
être modifiées sans avis préalable.
Informations complémentaires
34
Annexe
Informations complémentaires
Fr
Black plate (35,1)
Français
35Fr
Black plate (36,1)
Grazie per aver acquistato questo prodotto
PIONEER
Leggere attentamente questo manuale prima di
utilizzare il prodotto, per assicurarne il corretto
utilizzo. È particolarmente importante leggere e
osservare le precauzioni contrassegnate da AV-
VERTENZA e ATTENZIONE contenute in
questo manuale. Conservar e il manuale in un
luogo sicuro e accessibile, per consultazione futu-
ra.
Se si vuole eliminare questo prodotto, non
gettarlo insieme ai rifiuti domestici. Esiste un
sistema di raccolta differenziata in conformità
alle leggi che richiedono appositi trattamenti,
recupero e riciclo.
Gli utenti privati dei Paesi membri dellUnione
Europea, della Svizzera e della Norvegia posso-
no portare i propri prodotti elettronici gratuita-
mente presso i centri di raccolta specificati o
presso il rivenditore al dettaglio (se lacquisto è
stato eseguito presso un rivenditore di questo
tipo).
Per i Paesi non specificati in precedenza, contat-
tare le autorità locali per informazioni sul corret-
to metodo di smaltimento.
In questo modo si garantirà che il prodotto
smaltito subisca i processi di trattamento, recu-
pero e riciclaggio necessari per prevenire i po-
tenziali effetti negativi per lambiente e la salute
umana.
Informazioni sullunità
Le frequenze del sintonizzatore di questa unità
sono destinate alluso in Europa occidentale, in
Asia, nel Medio Oriente, in Africa e in Oceania.
Luso in altre aree può dare come risultato una
ricezione non adeguata. La funzione RDS (Radio
Data System) è utilizzabile solo nelle aree in cui
vengono trasmessi segnali RDS per stazioni FM.
AVVERTENZA
! Non cercare di installare o effettuare in-
terventi di manutenzione sul prodotto.
Linstallazione o lesecuzione di interven-
ti di manutenzione sul prodotto da parte
di persone sprovviste delle qualifiche o
dellesperienza richiesta per apparecchi
elettronici e accessori automobilistici po-
trebbe risultare pericolosa ed esporre a
rischi di scosse elettriche e di altre situa-
zioni pericolose.
! Non cercare di utilizzare i comandi dellunità
durante la guida. Prima di utilizzare i coman-
di dellunità, parcheggiare il veicolo in un
luogo sicuro.
ATTENZIONE
! Non lasciare che questa unità entri in contat-
to con liquidi, in caso contrario possono veri-
ficarsi scosse elettriche. Inoltre, se questa
unità entra in contatto con liquidi, può subire
danni oppure emettere fumo o surriscaldar-
si.
! Il CarStereo-Pass Pioneer può essere usato
solo in Germania.
! Mantenere sempre il volume basso abba-
stanza da poter udire i suoni provenienti dal-
lesterno.
! Evitare lesposizione allumidità.
ATTENZIONE
Questo apparecchio è un prodotto al laser di
Classe 1 secondo le norme di sicurezza dei
prodotti al laser IEC 60825-1:2007.
PRODOTTO LASER DI CLASSE 1
In caso di problemi
Nel caso che questa unità non funzioni corretta-
mente, contattare il rivenditore o il Centro di as-
sistenza autorizzato PIONEER più vicino.
Prima di iniziare
36
Sezione
Prima di iniziare
It
01
Black plate (37,1)
Unità principale
1 2 4 5
8 9
7 a c6 b d
3
1 h (espulsione)
2 iPod
3 Da 1/
a 6/
4 Vano dinserimento dei dischi
5 DISP
6 SRC/OFF
7 BAND/
(controllo iPod)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(indietro)/DIMMER (varialuce)
b
(lista)
c
Connettore di ingresso ausiliario (AUX) (con-
nettore stereo da 3,5 mm)
d Porta USB
ATTENZIONE
Utilizzare un cavo USB Pioneer opzionale (CD-
U50E) per collegare un lettore audio USB o un
dispositivo di memoria USB, in quanto se i di-
spositivi vengono collegati direttamente alluni-
tà, sporgeranno dalla stessa e potrebbero
risultare pericolosi.
Indicazioni sul display
31 4 86
a
2 5 7 9
b
1 (lista)
2
(controllo iPod)
La funzione iPod di questa unità è controlla-
ta dalliPod stesso.
3 Sezione delle informazioni secondarie
4 TA (notiziari sul traffico)
5
TP (identificazione dei programmi sul traffi-
co)
6
(Sound Retriever)
7 LOC (ricerca di sintonia in modo locale)
8
(ripetizione)
9
(casuale)
a
Sezione delle informazioni principali
! Sintonizzatore: banda e frequenza
! RDS: nome di servizio del programma,
informazioni PTY e altre informazioni let-
terali
! Sintolettore, dispositivo di memoria USB
e iPod: tempo di riproduzione trascorso
e informazioni di testo
b
Viene visualizzato quando esiste una cartella
o un menu di livello inferiore.
Menu di configurazione
1 Dopo aver installato lunità, portare l in-
terruttore della chiave di avviamento su ON.
Viene visualizzata lindicazione SET UP.
2 Ruotare M.C. per selezionare YES.
# Se non si effettuano operazioni con lunità per 30
secondi, il menu di configurazione non sarà visualiz-
zato.
# Se non si desidera eseguire la configurazione in
questo momento, ruotare M.C. per selezionare NO.
3 Premere M.C. per selezionare.
4 Per configurare il menu, eseguire questa
procedura.
Per passare allopzione di menu successiva, oc-
corre confermare la selezione.
LANGUAGE (multilingue)
Questa unità è in grado di visualizzare le informa-
zioni di testo dei file audio compressi se sono
state incorporate in inglese, russo o turco.
! Se la lingua incorporata e limpostazione della
lingua selezionata non corrispondono, le infor-
mazioni di testo potrebbero non essere visua-
lizzate correttamente.
! Alcuni caratteri potrebbero non essere visualiz-
zati correttamente.
1 Ruotare M.C. per selezionare limpostazione
desiderata.
ENG (Inglese)РУС (Russo)TUR (Turco)
2 Premere M.C. per confermare la selezione.
CLOCK SET (impostazione dellorologio)
1 Ruotare M.C. per regolare le ore.
2 Premere M.C. per selezionare i minuti.
3 Ruotare M.C. per regolare i minuti.
4 Premere M.C. per confermare la selezione.
FM STEP (passo di sintonizzazione FM)
Utilizzare FM STEP per impostare le opzioni relati-
ve al passo di sintonizzazione FM (impostazioni
per il passo di ricerca).
1 Ruotare M.C. per selezionare il passo di sinto-
nizzazione FM.
100 (100 kHz)50 (50 kHz)
2 Premere M.C. per confermare la selezione.
Viene visualizzata lindicazione QUIT.
! Il passo di sintonizzazione manuale è fissato a
50 kHz.
! Se le opzioni AF e TA sono disattivate, il passo
di ricerca è fissato a 50 kHz, anche se è stato
impostato su 100.
5 Per completare le impostazioni, ruotare
M.C. per selezionare YES.
# Se si desidera modificare ancora limpostazione,
ruotare M.C. per selezionare NO.
6 Premere M.C. per selezionare.
Italiano
Uso dellunità
37
Sezione
Uso dellunità
It
02
Black plate (38,1)
Note
! È possibile configurare le opzioni di menu
dal menu di sistema e dal menu iniziale. Per
informazioni dettagliate sulle impostazioni,
vedere Menu di sistema a pagina 44 e Menu
iniziale a pagina 44.
! È possibile annullare il menu di configurazio-
ne premendo SRC/OFF.
Funzionamento di base
Accensione dellunità
1 Premere SRC/OFF per accendere lunità.
Spegnimento dellunità
1 Premere e tenere premuto SRC/OFF fino a
quando lunità non si spegne.
Selezione di una sorgente
1 Premere SRC/OFF per passare in rassegna:
RADIOCDUSB/iPodAPP (applicazione)
AUX
! Quando è in uso la connessione MTP, viene vi-
sualizzata lindicazione USB MTP.
! Se è collegato un iPod ed è stata selezionata
una sorgente diversa da iPod, è possibile pas-
sare a iPod premendo iPod.
Regolazione del volume
1 Ruotare M.C. per regolare il volume.
Nota
Quando il conduttore isolato blu/bianco di que-
sta unità viene collegato al terminale di controllo
del relè dellantenna automatica, lantenna del-
lautomobile si estende quando si accende luni-
tà. Per ritirare lantenna, spegnere la sorgente.
Operazioni col menu più
frequentemente utilizzate
Ritorno al display precedente
Ritorno allelenco precedente (la cartella superio-
re di un livello)
1 Premere
/DIMMER.
Ritorno al display normale
Annullamento del menu principale
1 Premere BAND/
.
Ritorno al display normale dallelenco
1 Premere BAND/
.
Radio
Funzionamento di base
Selezione di una banda
1 Premere BAND/
fino a quando viene visua-
lizzata la banda desiderata (FM1, FM2, FM3
per FM o MW/LW).
Selezione delle stazioni preselezionate
1 Premere c o d.
! Selezionare PCH (canale preselezionato) in
SEEK per utilizzare questa funzione.
Sintonizzazione manuale (passo per passo)
1 Premere c o d.
! Selezionare MAN (sintonizzazione manuale)
in SEEK per utilizzare questa funzione.
Ricerca
1 Premere e tenere premuto c o d e poi rilascia-
re.
È possibile annullare la ricerca di sintonia pre-
mendo brevemente c o d.
Se si spinge e si tiene premuto c o d, è possi-
bile saltare le stazioni. La ricerca di sintonia
viene avviata non appena si rilascia c o d.
Note
! Per ulteriori dettagli sulla funzione SEEK, ve-
dere SEEK (impostazione tasto sinistro/de-
stro) a pagina 39.
! È possibile attivare e disattivare (on/off) la
funzione AF (ricerca delle frequenze alternati-
ve) di questa unità. Per le operazioni normali
di sintonizzazione, la funzione AF deve essere
disattivata (vedere AF (ricerca delle frequenze
alternative) a pagina 39).
Memorizzazione e richiamo delle
stazioni per ciascuna banda
Uso dei tasti di preselezione sintonia
1 Per memorizzare: Premere e tenere pre-
muto uno dei tasti di preselezione sintonia
(da 1/
a6/ ) fino a quando il numero
smette di lampeggiare.
2 Per richiamare: Premere uno dei tasti di
preselezione sintonia (da 1/
a6/ ).
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! FREQUENCY (nome di servizio del pro-
gramma o frequenza)
! BRDCST INFO (nome di servizio del pro-
gramma/Informazioni PTY)
! CLOCK (nome della sorgente e orologio)
Note
! Se non è possibile ottenere il nome di servi-
zio del programma in FREQUENCY, al suo
posto viene visualizzata la frequenza di tra-
smissione. Se invece il nome di servizio del
programma viene rilevato, verrà visualizzato.
! È possibile modificare le informazioni a se-
conda della banda.
! Le informazioni di testo che possono essere
modificate dipendono dallarea.
Uso delle funzioni PTY
È possibile sintonizzarsi su una stazione usando
le informazioni PTY (tipo di programma).
Ricerca di una stazione RDS tramite le informazio-
ni PTY
1 Premere
(elenco).
2 Ruotare M.C. per selezionare un tipo di pro-
gramma.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Premere M.C. per avviare la ricerca.
Lunità ricerca una stazione che trasmette il
tipo di programma selezionato. Quando viene
trovata una stazione, viene visualizzato il nome
di ser vizio del programma.
! Per annullare la ricerca premere nuova-
mente M.C.
! Il programma di alcune stazioni può essere
diverso da quello indicato dal PTY (tipo di
programma) trasmesso.
! Se nessuna stazione trasmette il tipo di
programma ricercato, per circa due secon-
di viene visualizzata lindicazione NOT
FOUND e poi il sintonizzatore torna alla
stazione originale.
Elenco PTY
Per ulteriori dettagli sullelenco PTY, visitare il
sito:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
Uso dellunità
38
Sezione
Uso dellunità
It
02
Black plate (39,1)
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
3 Ruotare M.C. per selezionare la funzione.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni descritte di seguito.
# Se è selezionata la banda MW/LW, è possibile se-
lezionare solo BSM, LOCAL o SEEK.
FM SETTING (impostazioni della qualità dellaudio
FM)
È possibile impostare il livello della qualità dellau-
dio in modo che corrisponda alle condizioni del
segnale trasmesso della banda FM.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
desiderata.
! STANDARD Corrisponde allimpostazio-
ne standard.
! HI-FI Utilizzare questa impostazione per
dare la priorità allalta qualità dellaudio
stereo.
! STABLE Utilizzare questa impostazione
per dare la priorità alla riduzione dei distur-
bi dellaudio mono.
BSM (memorizzazione delle stazioni migliori)
La funzione BSM (memorizzazione delle stazioni
migliori) memorizza automaticamente le sei sta-
zioni più forti in ordine di forza del segnale.
1 Premere M.C. per attivare la funzione BSM.
Per annullare, premere nuovamente M.C.
REGIONAL (regionale)
Quando si utilizza la funzione AF, la funzione regio-
nale limita la selezione alle stazioni che trasmetto-
no programmi regionali.
1 Premere M.C. per attivare o disattivare la fun-
zione regionale.
LOCAL (ricerca di sintonia in modo locale)
La ricerca di sintonia in modo locale consente di
sintonizzare solo le stazioni radio con segnali
radio sufficientemente potenti per una buona rice-
zione.
1 Premere M.C. per selezionare limpostazione
desiderata.
FM: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
Limpostazione di livello massimo consente la
ricezione solo delle stazioni più forti, mentre i
livelli più bassi consentono di ricevere stazioni
più deboli.
TA (attesa di notiziari sul traffico)
1 Premere M.C. per attivare o disattivare lattesa
di notiziari sul traffico.
AF (ricerca delle frequenze alternative)
1 Premere M.C. per attivare e disattivare la fun-
zione AF.
NEWS (interruzione dei programmi per i notiziari)
1 Premere M.C. per attivare o disattivare la fun-
zione NOTIZIE.
SEEK (impostazione tasto sinistro/destro)
È possibile assegnare una funzione ai tasti sinistro
e destro dellunità.
Selezionare MAN (sintonizzazione manuale) per
eseguire la sintonizzazione manuale o PCH (canali
preselezionati) per scegliere i canali preseleziona-
ti.
1 Premere M.C. per selezionare MAN o PCH.
CD/CD-R/CD-RW e dispositivi
di memoria USB
Collegamento MTP
È possibile connettere i dispositivi Android com-
patibili MTP (che eseguono Android OS 4.0 o
versione successiva) tramite collegamento MTP,
utilizzando la sorgente USB. Per collegare il di-
spositivo Android, utilizzare il cavo fornito col di-
spositivo.
Nota
Questa funzione non è compatibile con i file
WAV.
Funzionamento di base
Riproduzione di CD/CD-R/CD-RW
1 Inserire un disco nel vano dinserimento dei di-
schi, con il lato delletichetta rivolto verso
lalto.
Espulsione dei CD/CD-R/CD-RW
1 Premere h.
Riproduzione dei brani registrati su un dispositivo
di memoria USB
1 Sollevare la copertura della porta USB.
2 Collegare il dispositivo di memoria USB utiliz-
zando un cavo USB.
Arresto della riproduzione dei file sul dispositivo di
memoria USB
1 È possibile scollegare il dispositivo di memoria
USB in qualsiasi momento.
Selezione di una cartella
1 Premere 1/
o 2/ .
Selezione di una traccia
1 Premere c o d.
Esegue lavanzamento rapido/la modalità inversa
rapida
1 Premere e tenere premuto c o d.
! Quando si riproducono file audio compressi,
durante lavanzamento rapido e la modalità in-
versa non viene emesso audio.
Ritorno alla cartella principale
1 Premere e tenere premuto BAND/
.
Passaggio da audio compresso a CD-DA
1 Premere BAND/
.
Passaggio da un dispositivo di memoria per la ri-
produzione ad un altro
Se sono disponibili più dispositivi di memorizza-
zione di massa conformi con lo standard Mass
Storage Class USB, è possibile alternare i disposi-
tivi di memoria per la riproduzione.
1 Premere BAND/
.
! È possibile alternare fino a 32 differenti dispo-
sitivi di memoria.
Nota
Quando non utilizzati, scollegare i dispositivi di
memoria USB dallunità.
Italiano
Uso dellunità
39
Sezione
Uso dellunità
It
02
Black plate (40,1)
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
CD-DA
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
CD-TEXT
! TRACK INFO (titolo del brano/artista del
brano/titolo del disco)
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
MP3/WMA/WAV
! TRACK INFO (titolo del brano/nome del-
lartista/titolo dellalbum)
! FILE INFO (nome del file/nome della cartel-
la)
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
Selezione e riproduzione di file/
brani dallelenco dei nomi
1 Premere per passare alla modalità del-
lelenco dei nomi file/brani.
2 Utilizzare M.C. per selezionare il nome
del file (o il nome della cartella) desiderato.
Selezione di un file o di una cartella
1 Ruotare M.C.
Riproduzione
1 Quando è selezionato un file o un brano, pre-
mere M.C.
Visualizzazione di un elenco dei file (o delle cartel-
le) nella cartella selezionata
1 Quando è selezionata una cartella, premere
M.C.
Riproduzione di un brano nella cartella seleziona-
ta
1 Quando è selezionata una cartella, premere e
tenere premuto M.C.
Operazioni con i pulsanti speciali
Selezione di un intervallo di ripetizione
1 Premere 6/
per alternare:
CD/CD-R/CD-RW
! ALL Ripete tutti i brani
! ONE Ripete il brano corrente
! FLD Ripete la cartella corrente
Dispositivo di memoria USB
! ALL Ripete tutti i file
! ONE Ripete il file corrente
! FLD Ripete la cartella corrente
Riproduzione di brani in ordine casuale
1 Premere 5/
per attivare o disattivare la ri-
produzione casuale.
I brani contenuti nellintervallo di ripetizione
selezionato vengono riprodotti in ordine casua-
le.
! Per cambiare brano durante la riproduzione
casuale, premere d per passare al brano suc-
cessivo. Se si preme c, viene riavviata la ripro-
duzione del brano corrente dallinizio.
Messa in pausa della riproduzione
1 Premere 4/PAUSE per attivare o disattivare la
pausa.
Miglioramento dellaudio compresso e ripristino
del suono completo (funzione Sound Retriever)
1 Premere 3/S.Rtrv per passare in rassegna:
12OFF (disattivata)
1 è efficace per le velocità di compressione
basse, mentre 2 è efficace per le velocità di
compressione alte.
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
Dopo aver effettuato la selezione, è possibile re-
golare la funzione descritta di seguito.
S.RTRV (Sound Retriever)
Questa funzione migliora automaticamente lau-
dio compresso e ripristina il suono completo.
1 Premere M.C. per selezionare limpostazione
desiderata.
Per ulteriori dettagli, vedere Miglioramento del-
laudio compresso e ripristino del suono com-
pleto (funzione Sound Retriever) a pagina 40.
iPod
Funzionamento di base
Riproduzione di brani da un iPod
1 Sollevare la copertura della porta USB.
2 Collegare un iPod allingresso USB.
La riproduzione viene eseguita automatica-
mente.
Selezione di un brano (capitolo)
1 Premere c o d.
Selezione di un album
1 Premere 1/
o 2/ .
Esegue lavanzamento rapido/la modalità inversa
rapida
1 Premere e tenere premuto c o d.
Note
! Non è possibile accendere o spegnere liPod
se la modalità di controllo è impostata su
CTRL AUDIO.
! Scollegare gli auricolari dalliPod prima di
collegarlo a questa unità.
! LiPod si spegne circa due minuti dopo che
linterruttore della chiave di avviamento è
stato portato in posizione OFF.
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! TRACK INFO (titolo del brano/nome del-
lartista/titolo dellalbum)
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
Uso dellunità
40
Sezione
Uso dellunità
It
02
Black plate (41,1)
Scorrimento dei brani
1 Per passare al menu superiore della ricer-
ca delle liste, premere
.
2 Utilizzare M.C. per selezionare una cate-
goria/brano.
Modifica del nome del brano o della categoria
1 Ruotare M.C.
Liste di riproduzioneartistialbum brani
podcastgenericompositoriaudiolibri
Riproduzione
1 Mentre è selezionato un brano, premere M.C.
Visualizzazione di un elenco dei brani nella cate-
goria selezionata
1 Mentre è selezionata una categoria, premere
M.C.
Riproduzione di un brano nella categoria selezio-
nata
1 Mentre è selezionata una categoria, premere e
tenere premuto M.C.
Ricerca alfabetica nella lista
1 Quando viene visualizzata una lista per la cate-
goria selezionata, premere
per passare alla
modalità di ricerca alfabetica.
! È possibile anche passare alla modalità di
ricerca alfabetica ruotando M.C. due volte.
2 Ruotare M.C. per selezionare una lettera.
3 Premere M.C. per visualizzare lelenco in ordi-
ne alfabetico.
! Per annullare la ricerca, premere
/DIMMER.
Note
! È possibile riprodurre le liste di riproduzione
create con lapplicazione per computer
(MusicSphere). Lapplicazione sarà disponibi-
le sul nostro sito web.
! Le liste di riproduzione create con lapplica-
zione per computer (MusicSphere) vengono
visualizzate in forma abbreviata.
Operazioni con i pulsanti speciali
Selezione di un intervallo di ripetizione
1 Premere 6/
per alternare:
! ONE Ripete il brano corrente
! ALL Ripete tutti i brani dellelenco sele-
zionato
! Se la modalità di controllo è impostata su
CTRL iPod,lintervallo di riproduzione ripetuta
sarà uguale a quello impostato per liPod colle-
gato.
Selezione di un intervallo di riproduzione casuale
(modalità shuffle)
1 Premere 5/
per alternare:
! SNG Riproduce in ordine casuale i brani
contenuti nella lista selezionata.
! ALB Riproduce i brani contenuti in un
album selezionato in ordine casuale.
! OFF Non viene eseguita la riproduzione
casuale.
Riproduzione casuale di tutti i brani (shuffle all)
1 Premere e tenere premuto 5/
per attivare la
riproduzione casuale di tutti i brani.
! Per disattivare la riproduzione casuale di tutti i
brani, selezionare OFF nella riproduzione ca-
suale. Per ulteriori dettagli, vedere Selezione di
un intervallo di riproduzione casuale (modalità
shuffle) a pagina 41.
Messa in pausa della riproduzione
1 Premere 4/PAUSE per attivare o disattivare la
pausa.
Miglioramento dellaudio compresso e ripristino
del suono completo (funzione Sound Retriever)
1 Premere 3/S.Rtrv per passare in rassegna:
12OFF (disattivata)
1 è efficace per le velocità di compressione
basse, mentre 2 è efficace per le velocità di
compressione alte.
Riproduzione di brani correlati al
brano attualmente in riproduzione
È possibile riprodurre i brani dalle liste seguenti.
Lista degli album dellartista correntemente in
riproduzione
Lista dei brani dellalbum correntemente ripro-
dotto
Lista degli album del genere correntemente in
riproduzione
1 Premere e tenere premuto
per passare
alla modalità di riproduzione collegamento.
2 Ruotare M.C. per modificare la modalità;
premere per selezionare.
! ARTIST Riproduce un album dellartista at-
tualmente in riproduzione.
! ALBUM Riproduce un brano dellalbum at-
tualmente in riproduzione.
! GENRE Riproduce un album del genere at-
tualmente in riproduzione.
Dopo il brano attualmente in riproduzione, verrà
riprodotto il brano/album selezionato.
Note
! È possibile annullare il brano/album selezio-
nato, se si utilizzano funzioni diverse dalla ri-
cerca collegamento (ad esempio
lavanzamento o la modalità inversa rapidi).
! A seconda del brano selezionato per la ripro-
duzione, la fine del brano attualmente in ri-
produzione e linizio del brano/album
selezionato potrebbero essere tagliati.
Utilizzo della funzione iPod
dellunità dalliPod
È possibile controllare la funzione iPod di questa
unità tramite lapparecchio iPod collegato.
CTRL iPod non è compatibile con i seguenti mo-
delli di iPod.
! iPod nano di prima generazione
! iPod con video
% Premere BAND/
per alternare la modali-
di controllo.
! CTRL iPod È possibile utilizzare la funzione
iPod di questa unità tramite lapparecchio
iPod collegato.
! CTRL AUDIO È possibile controllare la fun-
zione iPod direttamente da questa unità.
È inoltre possibile alternare la modalità di con-
trollo premendo iPod.
Note
! Se si passa alla modalità di controllo
CTRL iPod, il brano attualmente in riprodu-
zione viene messo in pausa. Utilizzare i co-
mandi delliPod per riprendere la
riproduzione.
! Anche se la modalità di controllo è impostata
su CTRL iPod, è possibile controllare le se-
guenti funzioni da questa unità.
Pausa
Avanzamento rapido/modalità inversa rapida
Selezione di un brano (capitolo)
! È possibile controllare il volume solo da que-
sta unità.
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
3 Ruotare M.C. per selezionare la funzione.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni descritte di seguito.
! AUDIO BOOK non è disponibile se come mo-
dalità di controllo è selezionata limpostazio-
ne CTRL iPod. Per ulteriori dettagli, vedere
Utilizzo della funzione iPod dellunità dalliPod
a pagina 41.
Italiano
Uso dellunità
41
Sezione
Uso dellunità
It
02
Black plate (42,1)
AUDIO BOOK (velocità audiolibri)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
preferita.
! FASTER Riproduzione più veloce del nor-
male
! NORMAL Riproduzione normale
! SLOWER Riproduzione più lenta del nor-
male
S.RTRV (Sound Retriever)
1 Premere M.C. per selezionare limpostazione
desiderata.
Per ulteriori dettagli, vedere Miglioramento del-
laudio compresso e ripristino del suono com-
pleto (funzione Sound Retriever) a pagina 41.
Uso delle applicazioni del
dispositivo collegato
È possibile utilizzare questa unità per eseguire
riproduzioni in streaming e controllare i brani
nelle applicazioni per iPhone o solo per riprodu-
zioni in streaming.
Importante
Lutilizzo di applicazioni di terze parti potrebbe
comportare o richiedere di fornire informazio-
ni personali di identificazione attraverso la
creazione di un account utente o in altro
modo e, per alcune applicazioni, attraverso
linvio di dati di geolocalizzazione.
TUTTE LE APPLICAZIONI DI TERZE PARTI
SONO DI RESPONSABILITÀ ESCLUSIVA DEI
RISPETTIVI FORNITORI, INCLUSI MA NON LI-
MITATAMENTE ALLA GESTIONE E SICUREZ-
ZA DEI DATI UTENTE E ALLE PROCEDURE DI
TUTELA DELLA PRIVACY. ACCEDENDO AD
APPLICAZIONI DI TERZE PARTI, SI ACCETTA
DI ESAMINARE I TERMINI DEL SERVIZIO E I
CRITERI SULLA PRIVACY DEI FORNITORI. SE
NON SI ACCETTANO I TERMINI O I CRITERI
DI QUALSIASI FORNITORE O NON SI AC-
CONSENTE, DOVE SIA APPLICABILE, ALLU-
SO DEI DATI DI GEOLOCALIZZAZIONE, NON
UTILIZZARE TALI APPLICAZIONI DI TERZE
PARTI.
Informazioni sulla compatibilità
dei dispositivi collegati
Di seguito sono riportate informazioni dettaglia-
te relative ai terminali richiesti per utilizzare le
applicazioni per iPhone su questa unità.
Per gli utenti iPhone
! Questa funzione è compatibile con dispositi-
vi iPhone e iPod touch.
! Il dispositivo deve eseguire iOS 5.0 o versione
successiva.
Note
! Per lelenco delle applicazioni per iPhone
supportate da questa unità, consultare il no-
stro sito web.
! Pioneer non è responsabile di eventuali pro-
blemi che possono derivare da errori o difetti
del contenuto delle applicazioni.
! Il contenuto e la funzione delle applicazioni
supportate sono di responsabilità dei fornito-
ri delle applicazioni.
Procedura di inizio per utenti
iPhone
1 Collegare un iPhone allingresso USB.
2 Selezionare APP come sorgente.
3 Avviare lapplicazione sulliPhone e av-
viare la riproduzione.
Funzionamento di base
Selezione di una traccia
1 Premere c o d.
Esegue lavanzamento rapido/la modalità inversa
rapida
1 Premere e tenere premuto c o d.
Messa in pausa della riproduzione
1 Premere BAND/
per attivare la pausa o ri-
prendere la riproduzione.
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! TRACK INFO (titolo del brano/nome del-
lartista/titolo dellalbum)
! APP NAME (nome dellapplicazione)
! ELAPSED TIME (tempo di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
3 Ruotare M.C. per selezionare la funzione.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni descritte di seguito.
PAUSE (pausa)
1 Premere M.C. per attivare o disattivare la
pausa.
S.RTRV (Sound Retriever)
1 Premere M.C. per selezionare limpostazione
desiderata.
12OFF (disattivata)
1 è efficace per le velocità di compressione
basse, mentre 2 è efficace per le velocità di
compressione alte.
Regolazione dellaudio
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare AUDIO.
3 Ruotare M.C. per selezionare la funzione
audio.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni audio descritte di seguito.
! FADER non è disponibile se limpostazione
SUB.W/SUB.W è selezionata in
SP-P/O MODE. Per ulteriori dettagli, vedere
SP-P/O MODE (uscita posteriore e impostazio-
ne pre-out) a pagina 44.
! SUB.W e SUB.W CTRL non sono disponibili
se limpostazione REAR/REAR è selezionata
in SP-P/O MODE. Per ulteriori dettagli, vede-
re SP-P/O MODE (uscita posteriore e imposta-
zione pre-out) a pagina 44.
Uso dellunità
42
Sezione
Uso dellunità
It
02
Black plate (43,1)
! SUB.W CTRL non è disponibile se limposta-
zione SUB.W è selezionata in OFF. Per ulte-
riori dettagli, vedere SUB.W (impostazione
on/off del subwoofer) a pagina 43.
! SLA non è disponibile se come sorgente è se-
lezionata FM.
FADER (regolazione dissolvenza)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il bilanciamento
degli altoparlanti anteriori/posteriori.
BALANCE (regolazione del bilanciamento)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il bilanciamento del-
laltoparlante sinistro/destro.
EQ SETTING (richiamo dellequalizzatore)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare lequalizzatore.
POWERFULNATURALVOCALCU-
STOM1CUSTOM2FLATSUPER BASS
La banda di equalizzazione e il livello dellequa-
lizzatore possono essere personalizzati se è se-
lezionata limpostazione CUSTOM1 o
CUSTOM2.
Se si seleziona CUSTOM1 o CUSTOM2, com-
pletare la procedure descritta di seguito. Se si
selezionano altre opzioni, premere M.C. per
tornare al display precedente.
! Limpostazione CUSTOM1 può essere im-
postata separatamente per ciascuna sor-
gente. Tuttavia, USB, iPod e APP vengono
automaticamente configurate sulla stessa
impostazione.
! CUSTOM2 èunimpostazione condivisa
utilizzata per tutte le sorgenti.
3 Premere M.C. per visualizzare la modalità di
impostazione.
4 Premere M.C. per alternare le seguenti impo-
stazioni:
Banda dequalizzazioneLivello equalizzatore
5 Ruotare M.C. per selezionare limpostazione
desiderata.
Banda dequalizzazione: 80HZ250HZ
800HZ2.5KHZ8KHZ
Livello equalizzatore: +6 a 6
LOUDNESS (sonorità)
La sonorità compensa le deficienze nelle gamme
delle frequenze basse e alte a basso volume.
1 Premere M.C. per selezionare limpostazione
desiderata.
OFF (non attiva)LOW (bassa)MID (media)
HI (alta)
SUB.W (impostazione on/off del subwoofer)
Questa unità è dotata di unuscita subwoofer che
può essere attivata o disattivata.
1 Premere M.C. per selezionare limpostazione
desiderata.
NOR (fase normale)REV (fase invertita)
OFF (subwoofer disattivato)
SUB.W CTRL (regolazione del subwoofer)
Solo frequenze più basse di quelle presenti nellin-
tervallo selezionato vengono emesse dal subwoo-
fer.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per alternare le seguenti impo-
stazioni:
Frequenza di taglioLivello di uscitaLivello
pendenza
I valori regolabili lampeggiano.
3 Ruotare M.C. per selezionare limpostazione
desiderata.
Frequenza di taglio: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Livello di uscita: da 24 a +6
Livello pendenza: 12 24
BASS BOOST (incremento dei bassi)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare il livello desidera-
to.
A seconda se il livello aumenta o diminuisce,
viene visualizzata lindicazione da 0 a +6.
HPF SETTING (regolazione del filtro passa alto)
Utilizzare questa funzione se si desidera ascoltare
solo il segnale audio ad alta frequenza. Dagli alto-
parlanti verranno emesse solo le frequenze supe-
riori al limite del filtro passa alto (HPF).
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per alternare le seguenti impo-
stazioni:
Frequenza di taglioLivello pendenza
3 Ruotare M.C. per selezionare limpostazione
desiderata.
Frequenza di taglio: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Livello pendenza: 12 24
SLA (regolazione del livello della sorgente)
Questa funzione impedisce che il volume cambi in
modo eccessivo quando viene selezionata una sor-
gente diversa.
! Le impostazioni sono basate sul livello di volu-
me FM, che rimane immutato.
! Con questa funzione è anche possibile regola-
re il livello di volume MW/LW.
! USB, iPod e APP vengono automaticamente
configurate sulla stessa impostazione.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il volume della sor-
gente.
Intervallo di regolazione: da +4 a 4
Italiano
Uso dellunità
43
Sezione
Uso dellunità
It
02
Black plate (44,1)
Menu di sistema
Importante
La modalità PW SAVE (risparmio energetico)
viene annullata se la batteria del veicolo viene
scollegata e sarà necessario riattivarla dopo
aver ricollegato la batteria. Se la funzione
PW SAVE (risparmio energetico) è disattivata, a
seconda del metodo di collegamento, lunità po-
trebbe continuare a consumare energia dalla
batteria se linterruttore della chiave di avvia-
mento del veicolo non è dotato di posizione ACC
(accessori).
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
3 Ruotare M.C. per selezionare la funzione
del menu di sistema.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni del menu di sistema descritte
di seguito.
LANGUAGE (multilingue)
1 Premere M.C. per selezionare limpostazione
desiderata.
ENG (Inglese)РУС (Russo)TUR (Turco)
CLOCK SET (impostazione dellorologio)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per selezionare il segmento del
display dellorologio che si desidera impostare.
OraMinuto
3 Ruotare M.C. per regolare lorologio.
12H/24H (nota temporale)
1 Premere M.C. per selezionare limpostazione
desiderata.
12H (formato orologio a 12 ore)24H (formato
orologio a 24 ore)
AUTO PI (ricerca automatica PI)
Lunità può ricercare automaticamente una stazio-
ne diversa con la stessa programmazione, anche
durante il richiamo delle preselezioni.
1 Premere M.C. per attivare o disattivare la ricer-
ca automatica PI.
AUX (ingresso ausiliario)
Attivare questa impostazione se a questa unità
viene collegato un dispositivo ausiliario.
1 Premere M.C. per attivare o disattivare AUX.
DIMMER (varialuce)
1 Premere M.C. per attivare e disattivare il varia-
luce.
! È inoltre possibile modificare limpostazione
del varialuce premendo e tenendo premuto
/DIMMER.
MUTE MODE (modalità di silenziamento)
Il suono del sistema viene silenziato o attenuato
automaticamente quando viene ricevuto un se-
gnale da un apparecchio dotato di funzione di si-
lenziamento.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
desiderata.
! MUTE Silenziamento
! 20dB ATT Attenuazione (20dB ATT ha un
effetto più accentuato rispetto a 10dB ATT)
! 10dB ATT Attenuazione
PW SAVE (risparmio energetico)
Attivando questa funzione, è possibile ridurre il
consumo di energia della batteria.
! Lattivazione della sorgente è lunica operazio-
ne consentita quando questa funzione è attiva.
1 Premere M.C. per attivare o disattivare la mo-
dalità di risparmio energetico.
Menu iniziale
1 Premere e tenere premuto SRC/OFF fino
a quando lunità non si spegne.
2 Premere e tenere premuto SRC/OFF fino
a visualizzare sul display il menu principale.
3 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare INITIAL.
4 Ruotare M.C. per selezionare la funzione
del menu iniziale.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni del menu iniziale descritte di
seguito.
FM STEP (passo di sintonizzazione FM)
1 Premere M.C. per selezionare il passo di sinto-
nizzazione FM.
100 (100 kHz)50 (50 kHz)
SP-P/O MODE (uscita posteriore e impostazione
pre-out)
Le uscite degli altoparlanti posteriori e luscita
RCA di questa unità possono essere utilizzate per
collegare altoparlanti a gamma completa o un
subwoofer. Selezionare lopzione più adatta alla
configurazione.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
desiderata.
! REAR/SUB.W Selezionare quando alle
uscite degli altoparlanti posteriori sono col-
legati altoparlanti a gamma completa e al-
luscita RCA è collegato un subwoofer.
! SUB.W/SUB.W Selezionare quando alle
uscite degli altoparlanti posteriori è colle-
gato direttamente un subwoofer senza un
amplificatore ausiliario e alluscita RCA è
collegato un subwoofer.
! REAR/REAR Selezionare quando alle
uscite degli altoparlanti posteriori e allu-
scita RCA sono collegati altoparlanti a
gamma completa.
Se alle uscite degli altoparlanti posteriori è
collegato un altoparlante a gamma com-
pleta e luscita RCA non viene utilizzata, è
possibile selezionare REAR/SUB.W o
REAR/REAR.
Menu di sistema
1 Premere e tenere premuto SRC/OFF fino
a quando lunità non si spegne.
2 Premere e tenere premuto SRC/OFF fino
a visualizzare sul display il menu principale.
3 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
Uso dellunità
44
Sezione
Uso dellunità
It
02
Black plate (45,1)
4 Ruotare M.C. per selezionare la funzione
del menu di sistema.
Per ulteriori dettagli, vedere Menu di sistema a
pagina 44.
Uso della sorgente AUX
1 Collegare il cavo mini plug stereo al con-
nettore di ingresso ausiliario (AUX).
2 Premere SRC/OFF per selezionare AUX
come sorgente.
Nota
Non è possibile selezionare la sorgente AUX se
non viene attivata limpostazione dellapparec-
chio ausiliario. Per ulteriori dettagli, vedere AUX
(ingresso ausiliario) a pagina 44.
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! Nome sorgente
! Nome della sorgente e orologio
Se viene visualizzato un
display indesiderato
Per disattivare il display indesiderato, utilizzare
la procedura descritta di seguito.
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
3 Ruotare M.C. per visualizzare DEMO OFF,
quindi premere per selezionare.
4 Ruotare M.C. per selezionare YES.
5 Premere M.C. per selezionare.
Collegamenti
Importante
! Quando si installa questa unità in un veicolo
che non dispone della posizione ACC (acces-
soria) per linterruttore della chiave di avvia-
mento, se non si collega il cavo rosso a un
terminale accoppiato al funzionamento del-
linterruttore della chiave di avviamento, la
batteria potrebbe scaricarsi.
O
N
S
T
A
R
T
O
F
F
Con posizione ACC Senza posizione ACC
! Se questa unità viene utilizzata in condizione
diverse dalle seguenti, potrebbero verificarsi
incendi o malfunzionamenti.
Veicoli dotati di batteria da 12 volt e messa a
terra negativa.
Altoparlanti con uscita nominale da 50 W e
impedenza nominale compresa tra 4 W e8W.
! Per evitare rischi di cortocircuito, surriscalda-
mento o malfunzionamento, accertarsi di se-
guire le indicazioni riportate di seguito.
Prima dellinstallazione, scollegare il morset-
to negativo della batteria.
Assicurare i cavi con morsetti per cavi o na-
stro adesivo. Per proteggere i cavi, avvolgere
nastro adesivo attorno agli stessi nei punti in
cui entrano in contatto con parti metalliche.
Posizionare tutti i cavi in modo che non pos-
sano entrare in contatto con componenti mo-
bili, come la leva del cambio e i binari dei
sedili.
Non posizionare i cavi in luoghi soggetti a
surriscaldamento, come le bocchette dellim-
pianto di riscaldamento.
Non collegare il cavo giallo alla batteria fa-
cendolo passare attraverso fori nel vano mo-
tore.
Rivestire tutti i connettori scollegati con na-
stro isolante.
Non accorciare i cavi.
Non condividere mai lalimentazione con altri
dispositivi tagliando lisolante del cavo di ali-
mentazione dellunità. La capacità di carico
di corrente del cavo è limitata.
Utilizzare esclusivamente un fusibile con la
portata prescritta.
Non collegare mai direttamente a terra il
cavo negativo dellaltoparlante.
Non legare mai assieme cavi negativi di più
altoparlanti.
! Quando questa unità è accesa, i segnali di
controllo vengono trasmessi dal cavo blu/
bianco. Collegarlo al telecomando del siste-
ma di amplificazione di potenza o al termina-
le di controllo del relè dellantenna
automatica del veicolo (max. 300 mA
12 V CC). Se il veicolo è dotato di unantenna
a vetro, collegarla al terminale di alimentazio-
ne di potenza dellantenna.
! Non collegare mai il cavo blu/bianco al ter-
minale di alimentazione dellamplificatore di
potenza esterno. Inoltre, non collegarlo mai
al terminale di alimentazione dellantenna
automatica. In caso contrario, la batteria po-
trebbe scaricarsi o potrebbero verificarsi mal-
funzionamenti.
! Il cavo nero è la messa a terra. I cavi di
messa a terra di questa unità e di altre appa-
recchiature (soprattutto per i prodotti ad alta
tensione, quali amplificatori di potenza) de-
vono essere collegati separatamente. In caso
contrario, se scollegati accidentalmente, po-
trebbero provocare incendi o malfunziona-
menti.
Italiano
Uso dellunità
45
Sezione
Installazione
It
02
03
Black plate (46,1)
Questa unità
3
1 24
5
1 Ingresso antenna
2 Fusibile (10 A)
3 Ingresso cavo di alimentazione
4 Ingresso telecomando cablato
È possibile collegare un adattatore per tele-
comando cablato (venduto a parte).
5 Uscita posteriore o del subwoofer
Cavo di alimentazione
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Allingresso del cavo di alimentazione
2 A seconda del tipo di veicolo, la funzione di
3 e 5 potrebbe essere diversa. In questo
caso, accertarsi di collegare 4 a 5 e 6 a 3.
3 Giallo
Riserva (o accessorio)
4 Giallo
Collegare al terminale di alimentazione co-
stante 12 V.
5 Rosso
Accessorio (o riserva)
6 Rosso
Collegare al terminale controllato dallinter-
ruttore di accensione (12 V CC).
7 Collegare insieme i cavi dello stesso colore.
8 Nero (messa a terra telaio)
9 Blu/bianco
La posizione dei pin del connettore ISO sarà
diversa a seconda del tipo di veicolo. Collega-
re 9 e b quando il Pin 5 è del tipo controllo
antenna. In un altro tipo di veicolo, non colle-
gare mai 9 e b.
a Blu/bianco
Collegare al terminale di controllo del siste-
ma dellamplificatore di potenza (max.
300 mA 12 V CC).
b Blu/bianco
Collegare al terminale di controllo del relè
dellantenna automatica (max. 300 mA 12 V
CC).
c Giallo/nero
Se si utilizza un apparecchio dotato di funzio-
ne di silenziamento, collegare questo cavo al
cavo di silenziamento audio di tale apparec-
chio. In caso contrario, non collegare il cavo
di silenziamento audio.
d Cavi altoparlanti
Bianco: Anteriore sinistro +
Bianco/nero: Anteriore sinistro *
Grigio: Anteriore destro +
Grigio/nero: Anteriore destro *
Verde: Posteriore sinistro + o subwoofer +
Verde/nero: Posteriore sinistro * o subwoo-
fer *
Viola: Posteriore destro + o subwoofer +
Viola/nero: Posteriore destro * o subwoofer
*
e Connettore ISO
In alcuni veicoli, il connettore ISO potrebbe
essere diviso in due. In questo caso, accertar-
si di collegare entrambi i connettori.
Note
! Modifica delle impostazioni di menu iniziali
di questa unità. Vedere SP-P/O MODE (usci-
ta posteriore e impostazione pr e-out) a pagina
44.
Luscita subwoofer di questa unità è mono.
! Se si usa un subwoofer da 70 W (2 W), assicu-
rarsi di collegarlo ai fili viola e viola/nero di
questa unità. Non collegare niente ai fili
verde e verde/nero.
Amplificatore di poten za
(venduto a parte)
Eseguire questi collegamenti quando si usa
lamplificatore opzionale.
1
3
2
4
55
1 Telecomando sistema
Collegare al cavo Blu/bianco.
2 Amplificatore di potenza (venduto a parte)
3 Collegare con cavi RCA (venduti a parte)
4 Alluscita posteriore o del subwoofer
5 Altoparlanti posteriori o subwoofer
Installazione
Importante
! Controllare tutti i collegamenti e i sistemi
prima dellinstallazione finale.
! Non utilizzare componenti non approvati,
poiché potrebbero provocare malfunziona-
menti.
! Consultare il rivenditore se linstallazione ri-
chiede la trapanatura di fori o altre modifiche
del veicolo.
! Non installare questa unità se:
potrebbe interferire con il funzionamento del
veicolo.
potrebbe procurare lesioni al passeggero in
caso di arresto improvviso del veicolo.
! Se si surriscalda il laser a semiconduttore
potrebbe subire danni. Non installare questa
unità in luoghi soggetti a surriscaldamento,
come in prossimità delle bocchette dellim-
pianto di riscaldamento.
! Le prestazioni ottimali si ottengono quando
lunità viene installata con unangolazione in-
feriore a 60°.
60°
! Durante linstallazione, per assicurare la cor-
retta dissipazione del calore quando si utiliz-
za lunità, accertarsi di lasciare ampio spazio
dietro il pannello posteriore e avvolgere even-
tuali cavi allentati in modo che non ostrui-
scano le aperture.
5cmcm
Lasciare ampio spazio
5 cm
5 cm
! Durante linstallazione utilizzare componenti
disponibili in commercio.
Installazione
46
Sezione
Installazione
It
03
Black plate (47,1)
Come installare lunità
Questa unità può essere installata correttamen-
te utilizzando uno dei due metodi indicati di se-
guito.
! Installazione utilizzando il supporto
! Installazione utilizzando i fori delle viti ai lati
dellunità
Prima dellinstallazione dellunità
1 Rimuovere la guarnizione.
1
1 Guarnizione
2 Inserire le chiavi di estrazione fornite su
entrambi i lati dellunità fino a che non scat-
tano in posizione.
3 Estrarre lunità dal supporto.
Rimuovere il supporto.
1
1 Supporto
(componente montato in fabbrica)
Installazione utilizzando il supporto
1 Installare il supporto nel cruscotto.
Dopo aver inserito il supporto nel cruscotto, sce-
gliere e piegare le linguette in modo che corri-
spondano allo spessore del materiale del
cruscotto. (Installare lunità utilizzando le lin-
guette superiori e inferiori in modo che sia fissa-
ta il più saldamente possibile. Per un montaggio
sicuro, piegare le linguette a 90 gradi).
1
2
1 Cruscotto
2 Supporto
(componente montato in fabbrica)
2 Installare lunità.
1
1 Cruscotto
3 Collocare la guarnizione.
1
1 Guarnizione
Rimozione del supporto
La procedura è analoga a quella descritta in
Prima dellinstallazione dellunità. Per dettagli,
vedere Prima dellinstallazione dellunità a pagina
47.
Installazione utilizzando i fori
delle viti ai lati dellunità
% Fissare lunità alla staffa di montaggio
radio.
Posizionare lunità in modo che i fori per le viti
sullunità corrispondano ai fori per le viti sulla
staffa, quindi serrare le viti in 3 posizioni su cia-
scun lato.
1
2
4
3
1 Quando la linguetta si inserisce nel foro, pie-
garla verso il basso.
2 Staffa di montaggio radio
3 Vite a testa tonda (5 mm × 8 mm)
4 Cruscotto o console
Italiano
Installazione
47
Sezione
Installazione
It
03
Black plate (48,1)
Risoluzione dei problemi
In questo manuale i sintomi dei problemi sono
riportati in testo grassetto, mentre le cause sono
riportate in testo normale, non rientrato. Il testo
normale, ma rientrato indica le azioni da intra-
prendere.
Il display torna automaticamente alla
visualizzazione normale.
Non è stata eseguita alcuna operazione per 30 se-
condi.
Eseguire nuovamente loperazione.
Lintervallo di riproduzione ripetuta cambia im-
prevedibilmente.
A seconda dellintervallo di riproduzione ripetuta,
lintervallo selezionato potrebbe cambiare quando si
seleziona una cartella o un brano diverso, o quando
si procede allavanzamento rapido/modalità inversa.
Selezionare nuovamente lintervallo di
riproduzione ripetuta.
I brani di una sottocartella non vengono ripro-
dotti.
Non è possibile riprodurre i brani delle sottocartelle
se è selezionata lopzione FLD (ripetizione della car-
tella).
Selezionare un altro intervallo di riproduzione
ripetuta.
Quando cambia il display, viene visualizzata
unindicazione NO XXXX (ad esempio, NO TITLE).
Nel brano non è incorporata alcuna informazione di
testo.
Modificare la visualizzazione o riprodurre un altro
brano/file.
Malfunzionamento dellunità.
Ci sono interferenze.
Si utilizza un dispositivo, come un telefono cellulare,
che potrebbe provocare interferenze audio.
Spostare il dispositivo elettrico che causa
interferenze lontano dallunità.
Messaggi di errore
Se si contatta il rivenditore o il Centro assistenza
Pioneer più vicino, accertarsi di annotare il mes-
saggio di errore.
I messaggi di errore sono riportati in testo gras-
setto, mentre le cause sono riportate in testo
normale, non rientrato. Il testo normale, ma rien-
trato indica le azioni da intraprendere.
Problemi comuni
AMP ERROR
Lunità non funziona o laltoparlante non è collegato
correttamente; è stato attivato il circuito di protezio-
ne.
Controllare il collegamento degli altoparlanti. Se
il messaggio non scompare anche dopo aver
disattivato e riattivato lalimentazione, contattare
il rivenditore o la stazione assistenza PIONEER
più vicino.
Lettore CD
ERROR-07, 11, 12, 17, 30
Il disco è sporco.
Pulire il disco.
Il disco è graffiato.
Sostituire il disco.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Si è verificato un errore elettrico o meccanico.
Spegnere e accendere il motore oppure passare
a una sorgente diversa e poi di nuovo al lettore
CD.
ERROR-15
Il disco inserito è vuoto.
Sostituire il disco.
ERROR-23
Il formato del CD non è supportato.
Sostituire il disco.
FORMAT READ
A volte si verifica ritardo tra quando la riproduzione
viene avviata e quando si inizia a percepire il suono.
Attendere che il messaggio scompaia.
NO AUDIO
Il disco inserito non contiene file riproducibili.
Sostituire il disco.
SKIPPED
Il disco inserito contiene file protetti con tecnologia
DRM.
I file protetti vengono saltati.
PROTECT
Tutti i file nel disco inserito sono protetti da tecnolo-
gia DRM.
Sostituire il disco.
Dispositivo di memoria USB/iPod
FORMAT READ
A volte si verifica ritardo tra quando la riproduzione
viene avviata e quando si inizia a percepire il suono.
Attendere che il messaggio scompaia.
NO AUDIO
Assenza di brani.
Trasferire i file audio nel dispositivo di memoria
USB e stabilire il collegamento.
Il dispositivo di memoria USB collegato ha la prote-
zione attivata.
Seguire le istruzioni del dispositivo di memoria
USB per disattivare la protezione.
SKIPPED
Il dispositivo di memoria USB collegato contiene file
protetti da tecnologia DRM.
I file protetti vengono saltati.
PROTECT
Tutti i file sul dispositivo di memoria USB collegato
sono protetti da tecnologia DRM.
Sostituire il dispositivo di memoria USB.
N/A USB
Il dispositivo USB collegato non è supportato da que-
sta unità.
! Collegare un dispositivo USB compatibile con
lo standard MSC (Mass Storage Class).
! Scollegare il dispositivo e sostituirlo con un
dispositivo di memoria USB compatibile.
CHECK USB
Il connettore USB o il cavo USB è in cortocircuito.
Verificare che il connettore USB o il cavo USB
non sia incastrato o danneggiato.
CHECK USB
Il dispositivo di memoria USB collegato consuma
più della potenza massima consentita.
Scollegare il dispositivo di memoria USB e non
utilizzarlo. Portare linterruttore della chiave di
avviamento in posizione OFF, quindi su ACC o
ON e infine collegare solo dispositivi di memoria
USB compatibili.
Informazioni supplementari
48
Appendice
Informazioni supplementari
It
Black plate (49,1)
CHECK USB
LiPod funziona correttamente ma non si ricarica.
Accertarsi che il cavo di collegamento delliPod
non sia in cortocircuito (ad esempio, bloccato da
oggetti di metallo). Dopo aver verificato, portare
linterruttore della chiave di avviamento su OFF e
quindi su ON, oppure scollegare liPod e
collegarlo nuovamente.
ERROR-19
Errore di comunicazione.
Eseguire una delle operazioni riportate di
seguito.
Portare linterruttore della chiave di avviamento
in posizione OFF e quindi di nuovo su ON.
Scollegare il dispositivo di memoria USB.
Passare a una sorgente diversa.
Quindi, tornare alla sorgente USB.
Errore delliPod.
Scollegare il cavo dalliPod. Quando viene
visualizzato il menu principale delliPod,
collegare liPod e reimpostarlo.
ERROR-23
Il dispositivo di memoria USB non è formattato in
FAT12, FAT16 o FAT32.
Il dispositivo di memoria USB deve essere
formattato in FAT12, FAT16 o FAT32.
ERROR-16
La versione del firmware delliPod è obsoleta.
Aggiornare la versione delliPod.
Errore delliPod.
Scollegare il cavo dalliPod. Quando viene
visualizzato il menu principale delliPod,
collegare liPod e reimpostarlo.
STOP
Nessun brano presente nella lista corrente.
Selezionare una lista che contenga brani.
NOT FOUND
Non esistono brani correlati.
Scaricare i brani sulliPod.
Applicazione
START UP APP
Lapplicazione non è stata ancora avviata.
Seguire le istruzioni visualizzate sullo schermo.
Linee guida per luso corretto
Dischi e lettori
Utilizzare esclusivamente dischi che riportino uno
dei due seguenti loghi.
Utilizzare dischi da 12 cm.
Utilizzare esclusivamente dischi convenzionali,
completamente circolari.
Questa unità non può riprodurre i seguenti tipi di
dischi:
! DualDisc
! Dischi da 8 cm: se si cerca di utilizzare tali di-
schi con un adattatore, potrebbero verificarsi
malfunzionamenti dellunità.
! Dischi di forma irregolare
! Dischi diversi da CD
! Dischi danneggiati, inclusi dischi crepati,
scheggiati o piegati
! Dischi CD-R/RW non finalizzati
Non toccare la superficie registrata dei dischi.
Quando non si utilizzano, conservare i dischi nelle
rispettive custodie.
Non attaccare etichette, non scrivere e non appli-
care prodotti chimici sulla superficie dei dischi.
Per pulire un CD, passare delicatamente un
panno morbido sul disco procedendo dal centro
verso lesterno.
La formazione di condensa potrebbe temporanea-
mente limitare le prestazioni del lettore. In tal
caso, lasciarlo raggiungere una temperatura più
alta per circa unora. Inoltre, pulire i dischi che do-
vessero presentare condensa con un panno mor-
bido.
La riproduzione dei dischi potrebbe non essere
possibile a causa delle caratteristiche del disco,
del formato del disco, dellapplicazione di registra-
zione, dellambiente di riproduzione, delle condi-
zioni di conservazione e così via.
Le asperità della strada possono far interrompere
la riproduzione di un disco.
Se si utilizzano dischi sui quali è possibile applica-
re etichette, controllare le istruzioni e le avvertenze
dei dischi. Linserimento e lespulsione potrebbe
non riuscire, a seconda dei dischi. Luso di dischi
di questo tipo potrebbe danneggiare questa unità.
Non affiggere sui dischi etichette o altri materiali
disponibili in commercio.
! I dischi potrebbero deformarsi e non sarà più
possibile riprodurli.
! Le etichette potrebbero staccarsi durante la ri-
produzione, impedendo lespulsione dei di-
schi. Ciò potrebbe danneggiare questa unità.
Dispositivo di memoria USB
I collegamenti tramite hub USB non sono suppor-
tati.
Non collegare dispositivi diversi dai dispositivi di
memoria USB.
Durante la guida fissare saldamente il dispositivo
di memoria USB. Non lasciar cadere il dispositivo
di memoria USB sul fondo della vettura, dove po-
trebbe incastrarsi sotto il pedale del freno o del-
lacceleratore.
A seconda del dispositivo di memoria USB, po-
trebbero verificarsi i problemi seguenti.
! Le operazioni potrebbero risultare diverse.
! Il dispositivo di memoria potrebbe non essere
riconosciuto.
! I file potrebbero non essere riprodotti corretta-
mente.
! Il dispositivo potrebbe provocare interferenze
audio mentre si ascolta la radio.
iPod
Non lasciare liPod in luoghi soggetti a temperatu-
re elevate.
Durante la guida fissare saldamente liPod. Non
lasciar cadere liPod sul fondo della vettura, dove
potrebbe incastrarsi sotto il pedale del freno o del-
lacceleratore.
Italiano
Informazioni supplementari
49
Appendice
Informazioni supplementari
It
Black plate (50,1)
Informazioni sulle impostazioni delliPod
! Quando un iPod è collegato, questa unità di-
sattiva la funzione EQ (equalizzatore) delliPod
per ottimizzare lacustica. Quando si scollega
liPod, limpostazione EQ ritorna al valore origi-
nale.
! Non è possibile disattivare lopzione di ripeti-
zione delliPod se il dispositivo viene utilizzato
con questa unità. Lopzione di ripetizione viene
automaticamente modificata su Tutti quando
si collega liPod a questa unità.
Se il testo salvato sulliPod non è compatibile, non
verrà visualizzato da questa unità.
Compatibilità audio
compresso (dischi, USB)
WMA
Estensione file: .wma
Velocità in bit: da 48 kbps a 320 kbps (CBR), da
48 kbps a 384 kbps (VBR)
Frequenza di campionamento: 32 kHz, 44,1 kHz,
48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream con video: Non com-
patibile
MP3
Estensione file: .mp3
Velocità in bit: da 8 kbps a 320 kbps (CBR), VBR
Frequenza di campionamento: da 8 kHz a 48 kHz
(32 kHz, 44,1 kHz, 48 kHz per lenfatizzazione)
Versioni tag ID3 compatibili: 1.0, 1.1, 2.2, 2.3, 2.4
(alla tag ID3 Versione 2.x viene data la priorità ri-
spetto alla Versione 1.x.)
Compatibilità lista di riproduzione m3u: non com-
patibile
Compatibilità MP3i (MP3 interattivo), mp3 PRO:
non compatibile
WAV
Estensione file: .wav
Bit di quantizzazione lineare: 8 e 16 (LPCM), 4 (MS
ADPCM)
Frequenza di campionamento: da 16 kHz a 48 kHz
(LPCM), 22,05 kHz e 44,1 kHz (MS ADPCM)
! Non è possibile utilizzare questa funzione
con lopzione USB MTP.
Informazioni supplementari
Per i nomi dei file (incluse le estensioni) o i nomi
delle cartelle, è possibile visualizzare esclusiva-
mente i primi 32 caratteri.
Il testo cirillico da visualizzare su questa unità
deve essere codificato con uno dei seguenti set di
caratteri:
! Unicode (UTF-8, UTF-16)
! Un set di caratteri diverso da Unicode utilizzato
in ambiente Windows e impostato come cirilli-
co nellimpostazione multilingue
A seconda dellapplicazione utilizzata per codifica-
re i file WMA, questa unità potrebbe non funziona-
re correttamente.
In alcuni casi possono intercorrere alcuni istanti
prima dellavvio della riproduzione di file incorpo-
rati con dati immagine o file audio su dispositivi di
memoria USB con numerose gerarchie di cartelle.
Disco
Gerarchia delle cartelle riproducibili: fino a otto li-
velli (una gerarchia pratica non dovrebbe prevede-
re più di due livelli.)
Cartelle riproducibili: fino a 99
File riproducibili: fino a 999
File system: ISO 9660 di livello 1 e 2, Romeo, Joliet
Riproduzione multi-sessione: compatibile
Trasferimento dati con scrittura a pacchetti: non
compatibile
Indipendentemente dalla durata degli intervalli
vuoti tra i brani della registrazione originale, i di-
schi contenenti file audio compresso verranno ri-
prodotti con una breve pausa tra i brani.
Dispositivo di memoria USB
Gerarchia delle cartelle riproducibili: fino a otto li-
velli (una gerarchia pratica non dovrebbe prevede-
re più di due livelli.)
Cartelle riproducibili: fino a 500
File riproducibili: fino a 15 000
Riproduzione dei file con protezione del copyright:
non compatibile
Dispositivo di memoria USB partizionato: verrà ri-
prodotta solo la prima partizione riproducibile.
In alcuni casi possono intercorrere alcuni istanti
prima dellavvio della riproduzione di file audio su
un dispositivo di memoria USB con numerose ge-
rarchie di cartelle.
ATTENZIONE
! Pioneer non garantisce la compatibilità con
tutti i dispositivi di memoria USB e non si as-
sume alcuna responsabilità per leventuale
perdita di dati da lettori di file multimediali,
smart phone o altri dispositivi anche se i dati
vengono persi durante luso con questa
unità.
! Non lasciare dischi o dispositivi di memoria
USB in luoghi esposti ad alte temperature.
Compatibilità iPod
Lunità è compatibile esclusivamente con i se-
guenti modelli di iPod.
Compatibile con
! iPod touch (di quinta generazione)
! iPod touch (di quarta generazione)
! iPod touch (di terza generazione)
! iPod touch (di seconda generazione)
! iPod touch (di prima generazione)
! iPod classic
! iPod con video
! iPod nano (di settima generazione)
! iPod nano (di sesta generazione)
! iPod nano (di quinta generazione)
! iPod nano (di quarta generazione)
! iPod nano (di terza generazione)
! iPod nano (di seconda generazione)
! iPod nano (di prima generazione)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
A seconda della generazione o della versione
delliPod, alcune funzioni potrebbero non essere
disponibili.
Il funzionamento può variare a seconda della ver-
sione del sof tware di iPod.
Informazioni supplementari
50
Appendice
Informazioni supplementari
It
Black plate (51,1)
Gli utenti di iPod dotato di connettore Lightning
devono utilizzare il cavo adattatore da Lightning a
USB (fornito con liPod).
Gli utenti di iPod dotato di connettore Dock devo-
no utilizzare il cavo CD-IU51. Consultare il rivendi-
tore per ulteriori dettagli.
Per informazioni dettagliate sulla compatibilità di
file/formati, vedere i manuali delliPod.
Audiolibro, Podcast: compatibile
ATTENZIONE
Pioneer non si assume alcuna responsabilità
per leventuale perdita di dati dalliPod, anche se
i dati vengono persi durante luso di questa
unità.
Riproduzione in sequenza
dei file audio
Con questa unità, lutente non può assegnare i
numeri alle cartelle e specificare sequenze di ri-
produzione.
Esempio di gerarchia
1
2
3
4
5
6
01
02
03
04
05
Livello 1 Livello 2 Livello 3 Livello 4
: cartella
: file audio com-
presso
da 01 a 05: numero
della cartella
da 1 a 6: sequenza
di riproduzione
Disco
La sequenza di selezione delle cartelle o altre
operazioni potrebbero risultare differenti, a se-
conda del software utilizzato per la codifica o la
scrittura.
Dispositivo di memoria USB
La sequenza di riproduzione è la stessa della se-
quenza di registrazione sul dispositivo di memo-
ria USB.
Per specificare la sequenza di riproduzione, si
consiglia di utilizzare il seguente metodo.
1 Creare un nome file includendo i numeri che
specificano la sequenza di riproduzione (ad
esempio, 001xxx.mp3 e 099yyy.mp3).
2 Inserire tali file in una cartella.
3 Salvare la cartella contenente i file nel dispo-
sitivo di memoria USB.
Tuttavia, a seconda dellambiente di sistema, po-
trebbe non essere possibile specificare la se-
quenza di riproduzione.
Per i lettori audio portatili USB, la sequenza è di-
versa e dipende dal tipo di lettore.
Tabella dei caratteri cirillici
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Display C: Carattere
Copyright e marchi registrati
MP3
La fornitura di questo prodotto prevede il trasfe-
rimento di una licenza esclusivamente per uso
privato, non-commerciale e non prevede la con-
cessione di una licenza, implica qualsiasi di-
ritto a utilizzare questo prodotto in qualsiasi
trasmissione in diretta commerciale (ovvero,
che generi profitti) terrestre, via satellite, cavo e/
o tramite altro mezzo, trasmissioni/diffusioni tra-
mite Internet, Intranet e/o altre reti o in altri si-
stemi elettronici di distribuzione di contenuti,
come applicazioni di trasmissione audio a paga-
mento o audio-on-demand. Per tali usi è neces-
saria una licenza specifica. Per dettagli, visitare
http://www.mp3licensing.com.
WMA
Windows Media è un marchio di fabbrica o mar-
chio di fabbrica depositato della Microsoft
Corporation negli Stati Uniti ed in altri paesi.
Questo prodotto include tecnologie di proprietà
della Microsoft Corporation e non è utilizzbile
senza licenza della Microsoft Licensing, Inc.
iPod e iPhone
iPhone, iPod, iPod classic, iPod nano, e iPod
touch sono marchi di Apple Inc., registrati negli
Stati Uniti e in altri Paesi.
Lightning è un marchio di fabbrica di Apple Inc.
Fatto per l'iPod e Fatto per l'iPhone significa-
no che un accessorio elettronico è stato proget-
tato specificamente rispettivamente per il
collegamento con l'iPod o l'iPhone ed è stato
certificato dal suo sviluppatore corrispondere
agli standard operativi stabiliti da Apple. Apple
non può essere considerata responsabile di que-
sto dispositivo o della sua osservanza delle
norme di sicurezza e dei vari regolamenti. Tenere
presente che l'uso di questo accessorio con
l'iPod o l'iPhone può peggiorare le prestazioni
wireless.
Androidä
Android è un marchio di fabbrica di Google Inc.
Italiano
Informazioni supplementari
51
Appendice
Informazioni supplementari
It
Black plate (52,1)
Dati tecnici
Generali
Alimentazione .................. 14,4 V di c.c. (variazioni con-
sentite da 10,8 V a 15,1 V)
Messa a terra ................... Negativa
Consumo massimo .......... 10,0 A
Dimensioni (L × A × P):
DIN
Unità principale ............... 178 mm × 100 mm × 157 mm
Pannello anteriore ............ 188 mm × 118mm × 25mm
D
Unità principale ............... 178 mm × 100 mm × 165 mm
Pannello anteriore ............ 170 mm × 96mm × 17 mm
Peso ................................ 1,2 kg
Audio
Potenza duscita massima
................................... 50 W × 4
70 W × 1/2 W (per il subwoo-
fer)
Potenza duscita continua
................................... 22W × 4 (da 50Hz a
15 000 Hz, 5% THD, carico 4 W,
entrambi i canali)
Impedenza di carico ......... 4 W (variazioni consentite da
4 W a8W)
Livello massimo di uscita
................................... 2,0V
Contorno della sonorità .... +10dB (a 100Hz), +6,5 dB (a
10 kHz) (volume: 30 dB)
Equalizzatore (equalizzatore grafico a 5 bande):
Frequenza ........................ 80Hz/250 Hz/800 Hz/2,5 kHz/
8 kHz
Gamma di equalizzazione
................................... ±12 dB (a passi di 2 dB)
Subwoofer (mono):
Frequenze ........................ 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pendenza ......................... 12 dB per ottava, 24 dB per
ottava
Guadagno ........................ da +6dB a 24 dB
Fase ................................. Normale e invertita
Lettore CD
Sistema ........................... Sistema audio per compact
disc
Dischi utilizzabili .............. Compact disc
Rapporto segnale/rumore
................................... 94dB (a 1 kHz) (rete IEC-A)
Numero di canali ............. 2 (stereo)
Formato di decodifica MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato di decodifica WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ca-
nali audio)
(Windows Media Player)
Formato segnale WAV ...... PCM lineare & MS ADPCM
(Non compresso)
USB
Specifiche standard USB
................................... USB 2.0 massima velocità
Alimentazione massima ... 1 A
Classe USB ...................... MSC (Mass Storage Class)
File system ....................... FAT12, FAT16, FAT32
Formato di decodifica MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato di decodifica WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ca-
nali audio)
(Windows Media Player)
Formato segnale WAV ...... PCM lineare & MS ADPCM
(Non compresso)
Sintonizzatore FM
Gamma di frequenze ........ da 87,5 MHz a 108,0 MHz
Sensibilità ........................ 9dBf (0,8 µV/75 W, mono, rap-
porto S/R: 30 dB)
Rapporto segnale/rumore
................................... 72dB (rete IEC-A)
Sintonizzatore MW
Gamma di frequenze ........ da 531 kHz a 1 602kHz
Sensibilità ........................ 25µV (rapporto S/R: 20 dB)
Rapporto segnale/rumore
................................... 62dB (rete IEC-A)
Sintonizzatore LW
Gamma di frequenze ........ da 153 kHz a 281 kHz
Sensibilità ........................ 28µV (rapporto S/R: 20 dB)
Rapporto segnale/rumore
................................... 62dB (rete IEC-A)
Nota
Caratteristiche tecniche e design sono soggetti
a eventuali modifiche senza preavviso.
Informazioni supplementari
52
Appendice
It
Black plate (53,1)
Italiano
53It
Black plate (54,1)
Gracias por haber adquirido este producto
PIONEER
Lea con detenimiento este manual antes de utili-
zar el producto por primera vez para que pueda
darle el mejor uso posible. Es muy importante
que lea y cumpla con la información que apare-
ce bajo los mensajes de ADVERTENCIA y
PRECAUCIÓN de este manual. Una vez leído,
guarde el manual en un lugar seguro y a mano
para poder consultarlo en el futuro.
Si desea deshacerse de este producto, no lo
mezcle con los residuos generales de su
hogar. De conformidad con la legislación vi-
gente, existe un sistema de recogida distinto
para los productos electrónicos que requieren
un procedimiento adecuado de tratamiento,
recuperación y reciclado.
Las viviendas privadas en los estados miembros
de la UE, en Suiza y Noruega pueden devolver
gratuitamente sus productos electrónicos usa-
dos en los centros de recolección previstos o
bien en una tienda minorista (si adquieren un
producto similar nuevo).
En el caso de los países que no se han mencio-
nado en el párrafo anterior, póngase en contacto
con las autoridades locales a fin de conocer el
método de eliminación correcto.
Al actuar siguiendo estas instrucciones, se ase-
gurará de que el producto eliminado se someta
a los procesos de tratamiento, recuperación y
reciclaje necesarios, evitando de este modo
efectos potencialmente negativos en el entorno
y la salud humana.
Acerca de esta unidad
Las frecuencias del sintonizador de esta unidad
están asignadas para su uso en Europa Occi-
dental, Asia, Oriente Próximo, África y Oceanía.
El uso en otras áreas puede causar una recep-
ción deficiente. La función RDS (sistema de
datos de radio) opera sólo en áreas con emiso-
ras de FM que trasmitan señales de RDS.
ADVERTENCIA
! No trate de instalar o reparar este pro-
ducto usted mismo. La instalación o la
reparación de este producto por parte de
personas sin cualificación ni experiencia
en equipos electrónicos y accesorios
para automóviles puede ser peligrosa y
puede exponerle al riesgo de sufrir una
descarga eléctrica u otros peligros.
! No intente utilizar la unidad mientras esté
conduciendo. Asegúrese de salir de la carre-
tera y aparcar su vehículo en un lugar seguro
antes de intentar utilizar los controles del dis-
positivo.
PRECAUCIÓN
! Evite que esta unidad entre en contacto con
líquidos, ya que puede producir una descar-
ga eléctrica. Además, el contacto con líqui-
dos puede causar daños en la unidad, humo
y recalentamiento.
! El CarStereo-Pass de Pioneer solo debe usar-
se en Alemania.
! Mantenga siempre el volumen lo suficiente-
mente bajo como para poder escuchar los
sonidos que provienen del exterior.
! Evite la exposición a la humedad.
PRECAUCIÓN
Este aparato es un producto de láser de clase
1 clasificado como tal en Seguridad de pro-
ductos de láser, IEC 60825-1:2007.
PRODUCTO LASER CLASE 1
En caso de problemas con el
dispositivo
Si esta unidad no funcionase correctamente,
póngase en contacto con su concesionario o
con el centro de servicio PIONEER autorizado
más cercano.
Antes de comenzar
54
Sección
Antes de comenzar
Es
01
Black plate (55,1)
Unidad principal
1 2 4 5
8 9
7 a c6 b d
3
1 h (expulsar)
2 iPod
3 1/
a 6/
4 Ranura de carga de discos
5 DISP
6 SRC/OFF
7 BAND/
(control de iPod)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(parte posterior)/DIMMER (reductor de
luz)
b
(lista)
c
Conector de entrada AUX (conector estéreo
de 3,5 mm)
d Puerto USB
PRECAUCIÓN
Utilice un cable USB Pioneer opcional (CD-
U50E) para conectar el dispositivo de almacena-
miento USB, ya que cualquier dispositivo conec-
tado directamente a la unidad sobresaldrá de
ésta y podría resultar peligroso.
Indicaciones de la pantalla
31 4 86
a
2 5 7 9
b
1 (lista)
2
(control de iPod)
La función iPod de la unidad se controlará
desde el iPod.
3 Sección de información secundaria
4 TA (anuncios de tráfico)
5 TP (identificación de programa de tráfico)
6
(recuperador de sonido)
7 LOC (sintonización por búsqueda local)
8
(repetición)
9
(aleatorio)
a
Sección de información principal
! Sintonizador: banda y frecuencia
! RDS: nombre del servicio del programa,
información PTY y otro tipo de informa-
ción de texto
! Reproductor de CD, dispositivo de alma-
cenamiento USB y iPod: tiempo de re-
producción transcurrido e información
de texto
b
Aparece cuando existe un nivel, carpeta o
menú inferior.
Menú de configuración
1 Una vez instalada la unidad, gire la llave
de encendido hasta la posición ON.
Aparecerá SET UP.
2 Pulse M.C. para cambiar a YES.
# El menú de configuración desaparece si no utili-
za la unidad durante 30 segundos.
# Si prefiere dejar la configuración para más tarde,
gire M.C. para cambiar a NO.
3 Pulse M.C. para seleccionarlo.
4 Para configurar el menú, siga estos
pasos.
Para avanzar a la siguiente opción del menú
debe confirmar primero su selección.
LANGUAGE (idiomas múltiples)
Esta unidad puede mostrar la información de
texto de un archivo de audio comprimido incluso
para aquella información integrada en inglés,
ruso o turco.
! Si el idioma integrado y el idioma seleccionado
no coinciden, puede que la información de
texto no se muestre correctamente.
! Es posible que algunos caracteres no se visua-
licen correctamente.
1 Gire M.C. para seleccionar el ajuste deseado.
ENG (Inglés)РУС (Ruso)TUR (Turco)
2 Pulse M.C. para confirmar la selección.
CLOCK SET (ajuste del reloj)
1 Gire M.C. para ajustar la hora.
2 Presione M.C. para seleccionar el minuto.
3 Gire M.C. para ajustar el minuto.
4 Pulse M.C. para confirmar la selección.
FM STEP (paso de sintonía de FM)
Utilice FM STEP para ajustar las opciones de paso
de sintonía FM (ajustes del paso de búsqueda).
1 Gire M.C. para seleccionar el paso de sintonía
de FM.
100 (100 kHz)50 (50 kHz)
2 Pulse M.C. para confirmar la selección.
Aparecerá QUIT.
! El paso de sintonía manual está fijado en
50 kHz.
! Cuando se desactivan AF y TA, el paso de bús-
queda se fija en 50 kHz incluso si está ajustado
en 100.
5 Para cerrar la configuración, gire M.C. y
seleccione YES.
# Si prefiere volver a cambiar la configuración, gire
M.C. para cambiar a NO.
6 Pulse M.C. para seleccionarlo.
Español
Durante el uso de la unidad
55
Sección
Durante el uso de la unidad
Es
02
Black plate (56,1)
Notas
! Se pueden configurar las opciones del menú
desde el menú del sistema y desde el menú
de inicio. Si desea más información sobre
los ajustes, consulte Menú del sistema en la
página 61 y Menú inicial en la página 62.
! Si desea cancelar el menú de configuración,
pulse SRC/OFF.
Funcionamiento básico
Encendido de la unidad
1 Pulse SRC/OFF para encender la unidad.
Apagado de la unidad
1 Mantenga pulsado SRC/OFF hasta que se apa-
gue la unidad.
Selección de una fuente
1 Pulse SRC/OFF para desplazarse entre:
RADIOCDUSB/iPodAPP (aplicación)
AUX
! Se muestra USB MTP mientras está en uso la
conexión MTP.
! Si hay un iPod conectado y se selecciona una
fuente diferente a iPod, se podrá cambiar a
iPod pulsando iPod.
Ajuste del volumen
1 Gire M.C. para ajustar el volumen.
Nota
Si el cable azul/blanco de esta unidad está co-
nectado al terminal de control del relé de la an-
tena automática del vehículo, la antena se
extenderá cuando se encienda el equipo. Para
retraer la antena, apague la fuente.
Operaciones del menú
utilizadas frecuentemente
Retorno a la visualización anterior
Para volver a la lista anterior (la carpeta de un
nivel superior)
1 Pulse
/DIMMER.
Retorno a la visualización normal
Acceso al menú principal
1 Pulse BAND/
.
Retorno a la visualización normal desde la lista
1 Pulse BAND/
.
Radio
Funcionamiento básico
Selección de una banda
1 Pulse BAND/
hasta que se visualice la
banda deseada (FM1, FM2, FM3 para FM o
MW/LW).
Cambio de emisoras presintonizadas
1 Pulse c o d.
! Para utilizar esta función, seleccione PCH
(canal presintonizado) en SEEK.
Sintonización manual (paso a paso)
1 Pulse c o d.
! Para utilizar esta función, seleccione MAN
(sintonización manual) en SEEK.
Búsqueda
1 Mantenga pulsado c o d y luego suéltelo.
Se puede cancelar la sintonización por bús-
queda pulsando brevemente c o d.
Mientras mantiene pulsado c o d se pueden
saltar las emisoras. La sintonización por bús-
queda comienza inmediatamente después de
que suelte c o d.
Notas
! Para obtener detalles sobre SEEK, consulte
SEEK (ajuste tecla izquierda/derecha) en la pá-
gina 57.
! Se puede activar y desactivar la función AF
(búsqueda de frecuencias alternativas) de
esta unidad; se debe desactivar la función
AF para la sintonización normal (consulte AF
(búsqueda de frecuencias alternativas) en la
página 57).
Almacenamiento y recuperación
de emisoras para cada banda
Uso de los botones de ajuste de
presintonías
1 Para guardar: mantenga pulsado uno de
los botones de ajuste de presintonías (1/
a
6/
) hasta que el número deje de parpa-
dear.
2 Para recuperar emisoras: pulse uno de los
botones de ajuste de presintonías (1/
a6/
).
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! FREQUENCY (nombre del servicio de pro-
grama o frecuencia)
! BRDCST INFO (nombre del servicio de pro-
grama/información PTY)
! CLOCK (nombre de la fuente y reloj)
Notas
! Si no se puede adquirir el nombre del servi-
cio de programa en FREQUENCY, se visuali-
zará la frecuencia en su lugar. Si se detecta
el nombre del servicio de programa, se visua-
lizará el nombre del servicio de programa.
! Dependiendo de la banda, puede cambiarse
la información de texto.
! Los elementos de información de texto pue-
den cambiar según la zona.
Uso de las funciones PTY
Se puede sintonizar una emisora utilizando la
información PTY (tipo de programa).
Búsqueda de una emisora RDS por información
PTY
1 Pulse
(lista).
2 Gire M.C. para seleccionar el tipo de progra-
ma.
NEWS/INFOPOPULARCLASSICSOT-
HERS
3 Pulse M.C. para comenzar la búsqueda.
La unidad busca una emisora que transmita
ese tipo de programa, cuando la encuentra, se
visualiza el nombre del servicio de programa.
! Para cancelar la búsqueda, vuelva a pulsar
M.C.
! El programa de algunas emisoras puede
ser distinto al programa indicado por el
PTY transmitido.
! Si ninguna emisora está transmitiendo el
tipo de programa que busca, se visualizará
NOT FOUND durante unos dos segundos
y el sintonizador volverá a la emisora origi-
nal.
Lista PTY
Para obtener más detalles sobre la lista PTY, visi-
te la siguiente página web:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
Durante el uso de la unidad
56
Sección
Durante el uso de la unidad
Es
02
Black plate (57,1)
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
3 Gire M.C. para seleccionar la función.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones.
# Si se selecciona la banda MW/LW, solo estarán
disponibles BSM, LOCAL y SEEK.
FM SETTING (ajustes de calidad de sonido FM)
Puede ajustar el nivel de calidad del sonido para
que coincida con las condiciones de las señales
de emisión de la señal de banda FM.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ajuste deseado.
! STANDARD Es el ajuste estándar.
! HI-FI Es el ajuste que debe utilizar para
dar prioridad a la alta calidad del sonido
estéreo.
! STABLE Es el ajuste que debe utilizar
para dar prioridad al ruido bajo del sonido
monoaural.
BSM (memoria de las mejores emisoras)
BSM (memoria de las mejores emisoras) guarda
automáticamente las seis emisoras más fuertes
ordenadas por la intensidad de la señal.
1 Pulse M.C. para activar la función BSM.
Para cancelar, vuelva a pulsar M.C.
REGIONAL (regional)
Cuando se usa la función AF, la función regional li-
mita la selección de las emisoras a aquellas que
transmiten programas regionales.
1 Pulse M.C. para activar o desactivar la función
regional.
LOCAL (sintonización por búsqueda local)
La sintonización por búsqueda local le permite
sintonizar sólo las emisoras de radio con señales
lo suficientemente intensas como para asegurar
una correcta recepción.
1 Pulse M.C. para seleccionar el ajuste deseado.
FM: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
El ajuste de nivel superior solo permite recibir
las emisoras con las señales más intensas,
mientras que los ajustes más bajos permiten
recibir las emisoras con señales más débiles.
TA (espera por anuncio de tráfico)
1 Pulse M.C. para activar o desactivar la espera
por anuncio de tráfico.
AF (búsqueda de frecuencias alternativas)
1 Pulse M.C. para activar o desactivar la función
AF.
NEWS (interrupción por programa de noticias)
1 Pulse M.C. para activar o desactivar la función
NEWS.
SEEK (ajuste tecla izquierda/derecha)
Es posible asignar funciones a las teclas derecha
e izquierda de la unidad.
Seleccione MAN (sintonización manual) para
subir o bajar la frecuencia de forma manual o se-
leccione PCH (canales presintonizados) para cam-
biar entre los canales presintonizados.
1 Presione M.C. para seleccionar MAN o PCH.
CD/CD-R/CD-RW y dispositivos
de almacenamiento USB
Conexión MTP
Los dispositivos Android compatibles con MTP
(al ejecutar el sistema operativo Android 4.0 o
superior) se pueden conectar a través de la co-
nexión MTP utilizando la fuente USB. Para co-
nectar un dispositivo Android, utilice el cable
suministrado con el dispositivo.
Nota
Esta función no es compatible con WAV.
Funcionamiento básico
Reproducción de un CD/CD-R/CD-RW
1 Inserte el disco en la ranura de carga de dis-
cos con el lado de la etiqueta hacia arriba.
Expulsión de un CD/CD-R/CD-RW
1 Pulse h.
Reproducción de canciones de un dispositivo de
almacenamiento USB
1 Abra la tapa del puerto USB.
2 Conecte el dispositivo de almacenamiento
USB mediante un cable USB.
Detención de la reproducción de archivos en un
dispositivo de almacenamiento USB
1 Puede desconectar el dispositivo de almace-
namiento USB en cualquier momento.
Selección de una carpeta
1 Pulse 1/
o 2/ .
Selección de una pista
1 Pulse c o d.
Avance rápido o retroceso
1 Mantenga pulsado c o d.
! Al reproducir audio comprimido, no hay soni-
do durante el avance rápido o el retroceso.
Regreso a la carpeta raíz
1 Mantenga pulsado BAND/
.
Cambio entre audio comprimido y CD-DA
1 Pulse BAND/
.
Cambio entre dispositivos de memoria de repro-
ducción
Se puede cambiar entre dispositivos de memoria
de reproducción en dispositivos de almacena-
miento USB con más de un dispositivo de memo-
ria compatible con uno de almacenamiento
masivo.
1 Pulse BAND/
.
! Se puede cambiar hasta 32 dispositivos de
memoria diferentes.
Nota
Desconecte los dispositivos de almacenamiento
USB de la unidad cuando no los utilice.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
CD-DA
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
CD-TEXT
! TRACK INFO (título de la pista/artista de la
pista/título del disco)
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
MP3/WMA/WAV
! TRACK INFO (título de la pista/nombre del
artista/título del álbum)
! FILE INFO (nombre del fichero/nombre de
la carpeta)
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
Español
Durante el uso de la unidad
57
Sección
Durante el uso de la unidad
Es
02
Black plate (58,1)
Selección y reproducción de
archivos/pistas de la lista de
nombres
1 Pulse para cambiar al modo de lista
por nombre de archivo/pista.
2 Utilice M.C. para seleccionar el nombre
del archivo deseado (o de la carpeta).
Selección de un archivo o una carpeta
1 Gire M.C.
Reproducción
1 Tras seleccionar un archivo o una pista, pulse
M.C.
Visualización de una lista de los archivos (o las
carpetas) de la carpeta seleccionada
1 Tras seleccionar una carpeta, pulse M.C.
Reproducción de una canción de la carpeta selec-
cionada
1 Tras seleccionar una carpeta, mantenga pulsa-
do M.C.
Operaciones con botones especiales
Selección de un intervalo de repetición de repro-
ducción
1 Pulse 6/
para desplazarse entre las siguien-
tes opciones:
CD/CD-R/CD-RW
! ALL Repite todas las pistas
! ONE Repite la pista actual
! FLD Repite la carpeta actual
Dispositivo de almacenamiento USB
! ALL Repite todos los archivos
! ONE Repite el archivo actual
! FLD Repite la carpeta actual
Reproducción de las pistas en orden aleatorio
1 Pulse 5/
para activar o desactivar la repro-
ducción aleatoria.
Las pistas de una gama de repetición seleccio-
nada se reproducen en orden aleatorio.
! Para cambiar de canciones durante la repro-
ducción aleatoria, pulse d para cambiar a la
pista siguiente; si se pulsa c se reiniciará la
reproducción de la pista actual desde el princi-
pio de la canción.
Pausa de la reproducción
1 Pulse 4/PAUSE para pausar o reanudar.
Mejora del audio comprimido y restauración del
sonido óptimo (Sound Retriever)
1 Pulse 3/S.Rtrv para desplazarse entre:
12OFF (desactivado)
1 es efectivo para tasas de compresión baja, y
2 para tasas de compresión alta.
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
Una vez seleccionado, se puede ajustar la fun-
ción de abajo.
S.RTRV (recuperador de sonido)
Mejora automáticamente el audio comprimido y
restaura el sonido óptimo.
1 Pulse M.C. para seleccionar el ajuste deseado.
Para obtener más información, consulte Mejo-
ra del audio comprimido y restauración del soni-
do óptimo (Sound Retriever) en la página 58.
iPod
Funcionamiento básico
Reproducción de canciones en un iPod
1 Abra la tapa del puerto USB.
2 Conecte un iPod a la entrada USB.
La reproducción se inicia automáticamente.
Selección de una canción (capítulo)
1 Pulse c o d.
Selección de un álbum
1 Pulse 1/
o 2/ .
Avance rápido o retroceso
1 Mantenga pulsado c o d.
Notas
! El iPod no puede encenderse o apagarse
cuando el modo de control está ajustado en
CTRL AUDIO.
! Desconecte los auriculares del iPod antes de
conectarlo a esta unidad.
! El iPod se apagará aproximadamente dos mi-
nutos después de que la llave de encendido
del automóvil se ponga en OFF.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! TRACK INFO (título de la pista/nombre del
artista/título del álbum)
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
Para buscar una canción
1 Para ir al menú superior de la búsqueda
de listas, pulse
.
2 Utilice M.C. para seleccionar una catego-
ría/canción.
Cambio del nombre de la canción o la categoría
1 Gire M.C.
Listas de reproducciónartistasálbumes
cancionespodcastsgéneroscomposito-
resaudiolibros
Reproducción
1 Tras seleccionar una canción, pulse M.C.
Visualización de una lista de canciones de la cate-
goría seleccionada
1 Tras seleccionar una categoría, pulse M.C.
Durante el uso de la unidad
58
Sección
Durante el uso de la unidad
Es
02
Black plate (59,1)
Reproducción de una canción de la categoría se-
leccionada
1 Tras seleccionar una categoría, mantenga pul-
sado M.C.
Búsqueda alfabética en las listas
1 Cuando se visualice una lista de la categoría
seleccionada, pulse
para cambiar al modo
de búsqueda alfabética.
! Es posible cambiar al modo de búsqueda
por orden alfabético girando M.C. dos
veces.
2 Haga girar M.C. para seleccionar una letra.
3 Pulse M.C. para visualizar la lista alfabética.
! Para cancelar la búsqueda, pulse
/DIM-
MER.
Notas
! Es posible reproducir listas de reproducción
creadas con el programa de ordenador
(MusicSphere). Dicho programa estará dis-
ponible en nuestro sitio web.
! Las listas de reproducción creadas con el
programa de ordenador (MusicSphere) se
muestran de forma abreviada.
Operaciones con botones especiales
Selección de un intervalo de repetición de repro-
ducción
1 Pulse 6/
para desplazarse entre las siguien-
tes opciones:
! ONE Repite la canción actual
! ALL Repite todas las canciones de la
lista seleccionada
! Cuando el modo de control se ha ajustado en
CTRL iPod, el intervalo de repetición de repro-
ducción será el mismo que el que se ajustó
para el iPod conectado.
Selección de un intervalo de reproducción aleato-
rio (shuffle)
1 Pulse 5/
para desplazarse entre las si-
guientes opciones:
! SNG Reproduce canciones siguiendo un
orden aleatorio dentro de la lista.
! ALB Reproduce canciones siguiendo un
orden aleatorio dentro del álbum.
! OFF No se reproduce en orden aleatorio.
Reproducción de todas las canciones en orden
aleatorio (shuffle all)
1 Mantenga presionado 5/
para activar la
función de reproducción de todas las cancio-
nes en orden aleatorio (shuffle all).
! Para desactivar la reproducción de todas las
canciones en orden aleatorio, seleccione OFF
en reproducción aleatoria. Para más informa-
ción, consulte Selección de un intervalo de re-
producción aleatorio (shuffle) en la página 59.
Pausa de la reproducción
1 Pulse 4/PAUSE para pausar o reanudar.
Mejora del audio comprimido y restauración del
sonido óptimo (Sound Retriever)
1 Pulse 3/S.Rtrv para desplazarse entre:
12OFF (desactivado)
1 es efectivo para tasas de compresión baja, y
2 para tasas de compresión alta.
Reproducción de canciones
relacionadas con la canción que
se está reproduciendo
Se pueden reproducir canciones de las siguien-
tes listas:
Lista de álbumes del artista que se está repro-
duciendo
Lista de canciones del álbum que se está re-
produciendo
Lista de álbumes del género que se está repro-
duciendo
1 Mantenga pulsado
para cambiar al
modo de reproducción de enlace.
2 Haga girar M.C. para cambiar el modo y
pulse para seleccionarlo.
! ARTIST Reproduce un álbum del artista
que se está reproduciendo.
! ALBUM Reproduce una canción del álbum
que se está reproduciendo.
! GENRE Reproduce un álbum del género
que se está reproduciendo.
La canción o el álbum seleccionado se reprodu-
cirá después de la canción que se esté reprodu-
ciendo en ese momento.
Notas
! Se puede cancelar la canción o el álbum se-
leccionado mediante funciones diferentes a
la búsqueda de enlace (p. ej., avance rápido
y retroceso).
! Según la canción seleccionada, pueden cor-
tarse el final de la canción que se esté repro-
duciendo o el principio de la canción o del
álbum seleccionados.
Uso de la función iPod de la
unidad desde el iPod
La función iPod de esta unidad se puede contro-
lar desde el iPod conectado.
CTRL iPod no es compatible con los siguientes
modelos de iPod:
! iPod nano generación
! iPod con vídeo
% Pulse BAND/
para cambiar el modo de
control.
! CTRL iPod La función iPod de esta unidad
se puede utilizar desde el iPod conectado.
! CTRL AUDIO La función iPod de esta uni-
dad se puede controlar desde esta unidad.
También puede cambiar el ajuste de salida pre-
sionando iPod.
Notas
! Al cambiar el modo de control a CTRL iPod,
se pausa la reproducción de la canción. Utili-
ce el iPod para reanudar la reproducción.
! Las siguientes operaciones estarán disponi-
bles en esta unidad aunque se ajuste el
modo de control en CTRL iPod.
Pausa
Avance rápido/retroceso
Selección de una canción (capítulo)
! El volumen solo se puede controlar desde
esta unidad.
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
3 Gire M.C. para seleccionar la función.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones.
! AUDIO BOOK no está disponible cuando se
selecciona CTRL iPod en modo de control.
Para más información, consulte Uso de la
función iPod de la unidad desde el iPod en la
página 59.
Español
Durante el uso de la unidad
59
Sección
Durante el uso de la unidad
Es
02
Black plate (60,1)
AUDIO BOOK (velocidad del audiolibro)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar su ajuste favorito.
! FASTER Reproducción con velocidad su-
perior a la normal
! NORMAL Reproducción con velocidad
normal
! SLOWER Reproducción con velocidad in-
ferior a la normal
S.RTRV (recuperador de sonido)
1 Pulse M.C. para seleccionar el ajuste deseado.
Para obtener más información, consulte Mejo-
ra del audio comprimido y restauración del soni-
do óptimo (Sound Retriever) en la página 59.
Uso de las aplicaciones del
dispositivo conectado
Puede utilizar la unidad para reproducir y con-
trolar las pistas en aplicaciones de iPhone o
simplemente para reproducir música.
Importante
El uso de aplicaciones de terceros puede im-
plicar o necesitar la puesta a disposición de
información de identificación personal, bien
mediante la creación de una cuenta de usua-
rio o de algún otro modo, y, para ciertas apli-
caciones, la puesta a disposición de datos de
geoubicación.
TODAS LAS APLICACIONES DE TERCEROS
SON RESPONSABILIDAD EXCLUSIVA DE
LOS PROVEEDORES, INCLUIDAS SIN LIMI-
TACIÓN LA RECOPILACIÓN Y LA SEGURI-
DAD DE LOS DATOS DE USUARIO Y LAS
PRÁCTICAS DE PRIVACIDAD. AL ACCEDER
A APLICACIONES DE TERCEROS, USTED SE
MANIFIESTA DE ACUERDO EN REVISAR LOS
TÉRMINOS DE SERVICIO Y LAS POLÍTICAS
DE PRIVACIDAD DE LOS PROVEEDORES. SI
NO ESTÁ DE ACUERDO CON LOS TÉRMINOS
O LAS POLÍTICAS DE ALGÚN PROVEEDOR O
NO CONSIENTE EL USO DE DATOS DE
GEOUBICACIÓN DONDE SEA APLICABLE,
NO UTILICE ESTAS APLICACIONES DE TER-
CEROS.
Información acerca de la
compatibilidad de dispositivos
conectados
A continuación se muestra información detalla-
da acerca de las terminales necesarias para uti-
lizar la aplicación para iPhone en esta unidad.
Para usuarios de iPhone
! Esta función es compatible tanto con iPhone
como con iPod touch.
! El dispositivo tiene un iOS 5.0 o superior.
Notas
! Compruebe en nuestra página web la lista
de las aplicaciones de iPhone compatibles
con esta unidad.
! Pioneer no se responsabiliza de cualquier
problema que pueda surgir a causa de un
contenido incorrecto o defectuoso de la apli-
cación.
! El contenido y funcionamiento de las aplica-
ciones compatibles son responsabilidad de
los proveedores de las mismas.
Procedimiento de inicio para
usuarios de iPhone
1 Conecte un iPhone a una salida USB.
2 Cambie la fuente a APP.
3 Inicie la aplicación en el iPhone e inicie la
reproducción.
Funcionamiento básico
Selección de una pista
1 Pulse c o d.
Avance rápido o retroceso
1 Mantenga pulsado c o d.
Pausa de la reproducción
1 Pulse BAND/
para pausar o reanudar.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! TRACK INFO (título de la pista/nombre del
artista/título del álbum)
! APP NAME (nombre de la aplicación)
! ELAPSED TIME (tiempo de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
3 Gire M.C. para seleccionar la función.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones.
PAUSE (pausar)
1 Pulse M.C. para pausar o reanudar.
S.RTRV (recuperador de sonido)
1 Pulse M.C. para seleccionar el ajuste deseado.
12OFF (desactivado)
1 es efectivo para tasas de compresión baja, y
2 para tasas de compresión alta.
Ajustes de audio
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar AUDIO.
3 Gire M.C. para seleccionar la función de
audio.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones de audio.
! FADER no está disponible cuando se selec-
ciona SUB.W/SUB.W en SP-P/O MODE. Para
más información, consulte SP-P/O MODE
(ajuste de la salida posterior y del preamplifica-
dor) en la página 62.
Durante el uso de la unidad
60
Sección
Durante el uso de la unidad
Es
02
Black plate (61,1)
! SUB.W y SUB.W CTRL no están disponibles
cuando se selecciona REAR/REAR en
SP-P/O MODE. Para más información, con-
sulte SP-P/O MODE (ajuste de la salida poste-
rior y del preamplificador) en la página 62.
! SUB.W CTRL no está disponible cuando se
selecciona SUB.W en OFF. Para más infor-
mación, consulte SUB.W (ajuste de subgra-
ves activado/desactivado) en la página 61.
! SLA no está disponible si se ha seleccionado
FM como fuente.
FADER (ajuste de ecualizador)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el balance entre los alta-
voces delanteros/traseros.
BALANCE (ajuste del balance)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el balance de los altavo-
ces izquierdo o derecho.
EQ SETTING (recuperación de ecualizador)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ecualizador.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
La banda y el nivel de ecualización se pueden
personalizar si se selecciona CUSTOM1 o
CUSTOM2.
Si selecciona CUSTOM1 o CUSTOM2, com-
plete los pasos que se describen más abajo. Si
selecciona otras opciones, pulse M.C. para
volver a la pantalla anterior.
! CUSTOM1 se puede ajustar por separado
para cada fuente; no obstante, USB, iPod y
APP se ajustan igual automáticamente.
! CUSTOM2 es una configuración comparti-
da que se utiliza para todas las fuentes.
3 Pulse M.C. para mostrar el modo de ajuste.
4 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Banda de ecualizaciónNivel de ecualización
5 Gire M.C. para seleccionar el ajuste deseado.
Banda de ecualización: 80HZ250HZ
800HZ2.5KHZ8KHZ
Nivel de ecualización: +6 a 6
LOUDNESS (sonoridad)
La sonoridad compensa las deficiencias en los in-
tervalos de frecuencias bajas y altas cuando se es-
cucha a un volumen bajo.
1 Pulse M.C. para seleccionar el ajuste deseado.
OFF (desactivado)LOW (bajo)MID
(medio)HI (alto)
SUB.W (ajuste de subgraves activado/desactiva-
do)
Esta unidad está equipada con una salida de sub-
graves que se puede activar o desactivar.
1 Pulse M.C. para seleccionar el ajuste deseado.
NOR (fase normal)REV (fase inversa)OFF
(subgraves desactivados)
SUB.W CTRL (ajuste de subgraves)
Solo las frecuencias más bajas que aquellas en el
intervalo seleccionado se generan por el altavoz
de subgraves.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Frecuencia de corteNivel de salidaNivel de
pendiente
Las tasas que se puedan ajustar parpadearán.
3 Gire M.C. para seleccionar el ajuste deseado.
Frecuencia de corte: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Nivel de salida: de 24 a +6
Nivel de pendiente: 12 24
BASS BOOST (intensificación de graves)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el nivel que desee.
Se visualiza 0 a +6 mientras se aumenta o dis-
minuye el nivel.
HPF SETTING (ajuste del filtro de paso alto)
Utilice esta función si desea escuchar solo soni-
dos de alta frecuencia. Solamente se emiten por
los altavoces frecuencias más altas que el corte
del filtro de paso alto (HPF).
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Frecuencia de corteNivel de pendiente
3 Gire M.C. para seleccionar el ajuste deseado.
Frecuencia de corte: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Nivel de pendiente: 12 24
SLA (ajuste del nivel de fuente)
Esta función evita que el volumen cambie dema-
siado drásticamente cuando se cambia de fuente.
! Los ajustes se basan en el nivel de volumen de
FM, que se mantiene inalterado.
! El nivel del volumen de MW/LW también se
puede ajustar con esta función.
! USB, iPod y APP reciben el mismo ajuste auto-
máticamente.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el volumen de la fuente.
Gama de ajuste: de +4 a 4
Menú del sistema
Importante
PW SAVE (ahorro de energía) se cancela si la
batería del vehículo se desconecta, y se debe ac-
tivar de nuevo cuando se vuelva a conectar la
batería. Dependiendo de los métodos de cone-
xión, cuando PW SAVE (ahorro de energía) está
desactivado, la unidad puede seguir obteniendo
energía de la batería si la llave de encendido de
su vehículo no tiene posición ACC (accesorio).
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
3 Gire M.C. para seleccionar la función del
menú del sistema.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones del menú de sistema.
LANGUAGE (idiomas múltiples)
1 Pulse M.C. para seleccionar el ajuste deseado.
ENG (Inglés)РУС (Ruso)TUR (Turco)
CLOCK SET (ajuste del reloj)
Español
Durante el uso de la unidad
61
Sección
Durante el uso de la unidad
Es
02
Black plate (62,1)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para seleccionar el segmento de la
pantalla del reloj que desea ajustar.
HoraMinuto
3 Gire M.C. para ajustar el reloj.
12H/24H (anotación de la hora)
1 Pulse M.C. para seleccionar el ajuste deseado.
12H (reloj de 12 horas)24H (reloj de 24
horas)
AUTO PI (búsqueda PI automática)
La unidad puede buscar automáticamente una
emisora diferente con el mismo programa, incluso
durante la recuperación de emisoras presintoni-
zadas.
1 Pulse M.C. para activar o desactivar la función
de búsqueda PI automática.
AUX (entrada auxiliar)
Active este ajuste si utiliza un dispositivo auxiliar
conectado a esta unidad.
1 Pulse M.C. para activar o desactivar AUX.
DIMMER (atenuador de luz)
1 Pulse M.C. para activar o desactivar el atenua-
dor de luz.
! También se puede cambiar la configuración de
atenuador de luz manteniendo pulsado
/DIMMER.
MUTE MODE (modo de silencio)
El sonido proveniente de este sistema se silencia
o atenúa automáticamente cuando se recibe una
señal desde un equipo con función de silencia-
miento.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ajuste deseado.
! MUTE Silenciamiento
! 20dB ATT Atenuación (20dB ATT tiene
un efecto más potente que 10dB ATT)
! 10dB ATT Atenuación
PW SAVE (ahorro de energía)
La activación de esta función le permite reducir el
consumo de la batería.
! Cuando esta función está activada, la única
operación que se permite es el encendido de
la fuente.
1 Pulse M.C. para activar o desactivar el ahorro
de energía.
Menú inicial
1 Mantenga pulsado SRC/OFF hasta que se
apague la unidad.
2 Mantenga pulsado SRC/OFF hasta que
aparezca el menú principal en la pantalla.
3 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar INITIAL.
4 Gire M.C. para seleccionar la función del
menú de inicio.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones del menú inicial.
FM STEP (paso de sintonía de FM)
1 Pulse M.C. para seleccionar el paso de sinto-
nía de FM.
100 (100 kHz)50 (50 kHz)
SP-P/O MODE (ajuste de la salida posterior y del
preamplificador)
La salida de cables de altavoces traseros y la sali-
da RCA de esta unidad se puede usar para co-
nectar altavoces de gama completa o de
subgraves. Seleccione la opción adecuada para
su conexión.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ajuste deseado.
! REAR/SUB.W Seleccione cuando haya
conectado un altavoz de gama completa a
la salida de cables de altavoces traseros y
un subgrave a la salida RCA.
! SUB.W/SUB.W Seleccione cuando haya
conectado un subgrave directamente a la
salida de cables de altavoces traseros, sin
ningún amplificador auxiliar, y un subgrave
a la salida RCA.
! REAR/REAR Seleccione cuando exista
un altavoz de gama completa conectado a
la salida de cables de los altavoces trase-
ros y a la salida RCA.
Si hay un altavoz de gama completa conec-
tado a la salida de cables de los altavoces
traseros y la salida RCA no se utiliza, podrá
seleccionar REAR/SUB.W o REAR/REAR.
Menú del sistema
1 Mantenga pulsado SRC/OFF hasta que se
apague la unidad.
2 Mantenga pulsado SRC/OFF hasta que
aparezca el menú principal en la pantalla.
3 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
4 Gire M.C. para seleccionar la función del
menú del sistema.
Para obtener más información, consulte Menú
del sistema en la página 61.
Uso de una fuente AUX
1 Inserte el miniconector estéreo en el co-
nector de entrada AUX.
2 Pulse SRC/OFF para seleccionar AUX
como fuente.
Nota
No se puede seleccionar AUX si no se activa el
ajuste auxiliar. Para obtener más información,
consulte AUX (entrada auxiliar) en la página 62.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! Nombre de la fuente
! Nombre de la fuente y reloj
Si aparece un display no
deseado
Desactive el display no deseado mediante los
pasos que se indican a continuación.
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
3 Gire M.C. para visualizar DEMO OFF y
púlselo para realizar la selección.
4 Pulse M.C. para cambiar a YES.
5 Pulse M.C. para seleccionarlo.
Durante el uso de la unidad
62
Sección
Durante el uso de la unidad
Es
02
Black plate (63,1)
Conexiones
Importante
! Cuando esta unidad se instale en un ve-
hículo sin posición ACC (accesorio) en la
llave de encendido, el cable rojo se debe co-
nectar al terminal que pueda detectar la ope-
ración de la llave de encendido. De lo
contrario, puede descargarse la batería.
O
N
S
T
A
R
T
O
F
F
Posición ACC Sin posición ACC
! El uso de esta unidad en unas condiciones
distintas de las indicadas a continuación po-
dría causar incendios o fallos de funciona-
miento.
Vehículos con una batería de 12 voltios y co-
nexión a tierra negativa.
Altavoces con 50 W (valor de salida) y 4 W a
8 W (valor de impedancia).
! Para evitar cortocircuitos, sobrecalentamien-
to o fallos de funcionamiento, asegúrese de
seguir las siguientes instrucciones.
Desconecte el terminal negativo de la batería
antes de la instalación.
Asegure el cableado con pinzas para cables
o cinta adhesiva. Envuelva con cinta adhesiva
las partes en contacto con piezas metálicas
para proteger el cableado.
Mantenga los cables alejados de las partes
móviles, como la palanca de cambios y los
raíles de los asientos.
Coloque todos los cables alejados de lugares
calientes, como cerca de la salida del calefac-
tor.
No conecte el cable amarillo a la batería pa-
sándolo a través del orificio hasta el compar-
timiento del motor.
Cubra con cinta aislante los conectores de
cables que queden desconectados.
No acorte ningún cable.
Nunca corte el aislamiento del cable de ali-
mentación de esta unidad para compartir la
corriente con otros equipos. La capacidad de
corriente del cable es limitada.
Utilice un fusible con la intensidad nominal
indicada.
Nunca conecte el cable negativo de los alta-
voces directamente a tierra.
Nunca empalme los cables negativos de va-
rios altavoces.
! Cuando se enciende esta unidad, se emite
una señal de control a través del cable azul/
blanco. Conecte este cable al mando a dis-
tancia del sistema de un amplificador de po-
tencia externo o al terminal de control del
relé de la antena automática del vehículo
(máx. 300 mA 12 V cc). Si el vehículo posee
una antena integrada en el cristal del para-
brisas, conéctela al terminal de la fuente de
alimentación del amplificador de la antena.
! Nunca conecte el cable azul/blanco al termi-
nal de potencia de un amplificador de poten-
cia externo, ni al terminal de potencia de la
antena automática, de lo contrario, puede
descargarse la batería o producirse un fallo
de funcionamiento.
! El cable negro es el cable a tierra. Los cables
a tierra de esta unidad y de otros productos
(especialmente productos de alta tensión,
como amplificadores de potencia) se deben
conectar por separado, de lo contrario,
puede producirse un incendio o un fallo de
funcionamiento si se desconectan por acci-
dente.
Esta unidad
3
1 24
5
1 Entrada de la antena
2 Fusible (10 A)
3 Entrada del cable de alimentación
4 Entrada remota conectada
Es posible conectar un adaptador de mando
a distancia físicamente conectado (se vende
por separado).
5 Salida trasera o salida de subgraves
Cable de alimentación
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 A la toma del cable de alimentación
2 Según el tipo de vehículo, las funciones de
3 y 5 pueden ser diferentes. En este caso,
conecte 4 a 5 y 6 a 3.
3 Amarillo
Reserva (o accesorio)
4 Amarillo
Conectar al terminal de alimentación cons-
tante de 12 V.
5 Rojo
Accesorio (o reserva)
6 Rojo
Conectar al terminal controlado por la llave
de encendido (12 V CC).
7 Conecte entre los cables del mismo color.
8 Negro (Toma de tierra del chasis)
9 Azul/blanco
La posición de las patillas del conector ISO
será diferente según el tipo de vehículo. Co-
necte 9 y b cuando la patilla 5 sea del tipo
control de antena. En otro tipo de vehículo,
no se deben conectar nunca 9 y b.
a Azul/blanco
Conectar al terminal de control del sistema
del amplificador de potencia (máx. 300 mA
12 V CC).
b Azul/blanco
Conectar al terminal de control del relé de la
antena automática (máx. 300 mA 12 V CC).
c Amarillo/negro
Si utiliza un equipo con función de silencia-
miento, conecte este cable con el cable de si-
lenciamiento de audio de ese equipo. En
caso contrario, mantenga el cable de silen-
ciamiento de audio sin ninguna conexión.
d Cables de altavoces
Blanco: delantero izquierdo +
Blanco/negro: delantero izquierdo *
Gris: delantero derecho +
Gris/negro: delantero derecho *
Verde: trasero izquierdo + o altavoz de sub-
graves +
Español
Instalación
63
Sección
Instalación
Es
03
Black plate (64,1)
Verde/negro: trasero izquierdo * o altavoz de
subgraves *
Violeta: trasero derecho + o altavoz de sub-
graves +
Violeta/negro: trasero derecho * o altavoz
de subgraves *
e Conector ISO
En algunos vehículos, el conector ISO puede
estar dividido en dos. En este caso, asegúre-
se de conectar los dos conectores.
Notas
! Cambie el menú inicial de esta unidad. Con-
sulte SP-P/O MODE (ajuste de la salida pos-
terior y del preamplificador) en la página 62.
La salida de graves de esta unidad es mo-
noaural.
! Al usar un altavoz de subgraves de 70 W
(2 W), conecte el mismo a los cables violeta y
violeta/negro de esta unidad. No conecte
nada al cable verde ni al verde/negro.
Amplificador de potencia (se
vende por separado)
Realice estas conexiones cuando utilice el am-
plificador opcional.
1
3
2
4
55
1 Control remoto del sistema
Conexión a cable azul/blanco.
2 Amplificador de potencia (se vende por sepa-
rado)
3 Conectar con cables RCA (se venden por se-
parado)
4 A la salida trasera o salida de subgraves
5 Altavoz trasero o altavoz de subgraves
Instalación
Importante
! Compruebe todas las conexiones y sistemas
antes de la instalación final.
! No utilice piezas no autorizadas, ya que pue-
den causar fallos de funcionamiento.
! Consulte a su distribuidor si para la instala-
ción es necesario taladrar orificios o hacer
otras modificaciones al vehículo.
! No instale esta unidad en un lugar donde:
Pueda interferir con el manejo del vehículo.
Pueda lesionar a un pasajero como conse-
cuencia de un frenazo brusco.
! El láser semiconductor se dañará si se sobre-
calienta. Instale esta unidad alejada de
zonas que alcancen altas temperaturas,
como cerca de la salida del calefactor.
! Se logra un rendimiento óptimo si la unidad
se instala en un ángulo inferior a 60°.
60°
! Cuando instale, para asegurar la dispersión
apropiada del calor durante el uso de esta
unidad, asegúrese de dejar un amplio espa-
cio por detrás del panel trasero y enrolle los
cables sueltos de modo que no bloqueen las
aberturas de ventilación.
Deje un amplio espacio
5 cm
5 cm
! En la instalación, emplee piezas disponibles
en el mercado.
Cómo realizar la instalación
Esta unidad se puede instalar utilizando uno de
los siguientes dos métodos:
! Instalación con el soporte
! Instalación usando los agujeros para torni-
llos ubicados en ambos costados de la uni-
dad
Antes de instalar esta unidad
1 Retire el anillo de guarnición.
1
1 Anillo de guarnición
2 Inserte en ambos lados de la unidad las
llaves de extracción provistas hasta que se
escuche un ligero chasquido.
3 Extraiga la unidad del soporte.
Retire el soporte.
1
1 Soporte
(pieza suministrada de fábrica)
Instalación con el soporte
1 Instale el soporte en el panel.
Después de insertar el soporte en el panel, se-
leccione las pestañas que se acoplen al espesor
del material del panel, y dóblelas (instale esta
unidad tan firmemente como sea posible, usan-
do las pestañas superior e inferior; para fijar la
unidad, doble las pestañas 90 grados).
1
2
1 Salpicadero
2 Soporte
(pieza suministrada de fábrica)
Instalación
64
Sección
Instalación
Es
03
Black plate (65,1)
2 Instale esta unidad.
1
1 Salpicadero
3 Coloque el anillo de guarnición.
1
1 Anillo de guarnición
Cómo retirar el soporte
El procedimiento es igual al de Antes de instalar
esta unidad. Para más información, consulte
Antes de instalar esta unidad en la página 64.
Instalación usando los agujeros
para tornillos ubicados en
ambos costados de la unidad
% Fijar la unidad al soporte de montaje de
radio de fábrica.
Coloque la unidad de forma que los orificios
para los tornillos estén alineados con los orifi-
cios para los tornillos de la carcasa y, a conti-
nuación, apriete los tornillos en tres lugares en
cada lado.
1
2
4
3
1 Si la lengüeta supone un impedimento, dó-
blela hacia abajo.
2 Soporte de montaje de radio de fábrica
3 Tornillos de cabeza redonda (5 mm × 8 mm)
4 Salpicadero o consola
Solución de problemas
Los síntomas se escriben en negrita y las cau-
sas en escritura normal sin sangría. El texto nor-
mal con sangría se utiliza para indicar las
acciones que se han de tomar.
La pantalla vuelve automáticamente a la
visualización normal.
No ha realizado ninguna operación en aproximada-
mente 30 segundos.
Realice la operación de nuevo.
El intervalo de repetición de reproducción cambia
de manera inesperada.
Dependiendo del intervalo de repetición de repro-
ducción, el intervalo seleccionado puede cambiar
cuando se selecciona otra carpeta o pista o cuando
se utilice el avance rápido/retroceso.
Seleccione de nuevo el intervalo de repetición de
reproducción.
No se reproduce una subcarpeta.
No se pueden reproducir las subcarpetas cuando se
selecciona FLD (repetición de carpeta).
Seleccione otro intervalo de repetición de
reproducción.
NO XXXX aparece cuando se cambia una pantalla
(NO TITLE, por ejemplo).
No hay información de texto incorporada.
Cambie la pantalla o reproduzca otra pista/
archivo.
La unidad no funciona correctamente.
Hay una interferencia.
Está utilizando un dispositivo, como un teléfono
móvil, que puede causar interferencias.
Aleje de la unidad los dispositivos eléctricos que
puedan estar causando interferencias.
Mensajes de error
Anote el mensaje de error antes de contactar
con su concesionario o con el servicio técnico
oficial de Pioneer más cercano.
Los mensajes de error se escriben en negrita y
producen un texto normal sin sangrado. El texto
normal y sangrado se emplea para indicar las
acciones que se han de tomar.
Comunes
AMP ERROR
La unidad no funciona o la conexión de los altavoces
es incorrecta; se activa el circuito de protección.
Compruebe la conexión de los altavoces. Si el
mensaje no desaparece aun después de apagar
y volver a encender el motor, contacte con su
distribuidor o con el Servicio técnico oficial
Pioneer.
Reproductor de CD
ERROR-07, 11, 12, 17, 30
El disco está sucio.
Limpie el disco.
El disco está rayado.
Sustituya el disco.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Se ha producido un error eléctrico o mecánico.
Coloque la llave de encendido del automóvil en
la posición de desactivación y luego pase de
nuevo a activación, o cambie a una fuente
diferente y, a continuación, vuelva a activar el
reproductor de CD.
ERROR-15
El disco insertado aparece en blanco.
Sustituya el disco.
Español
Instalación
65
Sección
Información adicional
Es
03
Black plate (66,1)
ERROR-23
Formato de CD no compatible.
Sustituya el disco.
FORMAT READ
A veces se produce un retraso entre el comienzo de
la reproducción y la emisión del sonido.
Espere hasta que el mensaje desaparezca y oiga
sonido.
NO AUDIO
El disco insertado no contiene archivos reproduci-
bles.
Sustituya el disco.
SKIPPED
El disco insertado contiene archivos protegidos con
DRM.
Los archivos protegidos se saltan.
PROTECT
Todos los archivos del disco insertado tienen DRM
integrado.
Sustituya el disco.
Dispositivo de almacenamiento USB o
iPod
FORMAT READ
A veces se produce un retraso entre el comienzo de
la reproducción y la emisión del sonido.
Espere hasta que el mensaje desaparezca y oiga
sonido.
NO AUDIO
No hay canciones.
Transfiera los archivos de audio al dispositivo de
almacenamiento USB y conéctelo.
El dispositivo de almacenamiento USB conectado
tiene la seguridad activada.
Para desactivar la seguridad, siga las
instrucciones del dispositivo de almacenamiento
USB.
SKIPPED
El dispositivo de almacenamiento USB conectado
tiene archivos protegidos con DRM.
Los archivos protegidos se saltan.
PROTECT
Todos los archivos en el dispositivo de almacena-
miento USB conectado tienen DRM integrado.
Cambie el dispositivo de almacenamiento USB.
N/A USB
El dispositivo USB conectado no es compatible con
esta unidad.
! Conecte un dispositivo que cumpla con la
clase de almacenamiento masivo USB.
! Desconecte su dispositivo y sustitúyalo por un
dispositivo de almacenamiento USB compatible.
CHECK USB
El conector USB o el cable USB está cortocircui-
tado.
Compruebe que el conector USB o el cable USB
no esté enganchado en algo ni dañado.
CHECK USB
El dispositivo de almacenamiento USB consume
más de la corriente máxima admisible.
Desconecte el dispositivo de almacenamiento
USB y no lo utilice. Coloque la llave de
encendido del automóvil en posición OFF, luego
en ACC u ON y, a continuación, conecte
únicamente dispositivos de almacenamiento
USB compatibles.
CHECK USB
El iPod funciona correctamente pero no se carga.
Compruebe que el cable de conexión del iPod no
esté cortocircuitado (p. ej., atrapado entre
objetos metálicos). Una vez confirmado, cambie
la llave de encendido del automóvil a la posición
de desactivación y luego pase de nuevo a
activación; o bien desconecte una vez el iPod y
conéctelo de nuevo.
ERROR-19
Error de comunicación.
Realice una de las siguientes operaciones:
Cambie la llave de encendido del automóvil a la
posición de desactivación y luego pase de nuevo
a activación.
Desconecte el dispositivo de almacenamiento
USB.
Cambie a una fuente diferente.
Después vuelva a la fuente USB.
Fallo del iPod.
Desconecte el cable del iPod. Una vez que
aparezca el menú principal del iPod, vuelva a
conectar el iPod y reinícielo.
ERROR-23
El dispositivo de almacenamiento USB no está for-
mateado con FAT12, FAT16 ni FAT32.
El dispositivo de almacenamiento USB debe
formatearse con FAT12, FAT16 o FAT32.
ERROR-16
La versión de firmware del iPod es antigua.
Actualice la versión del iPod.
Fallo del iPod.
Desconecte el cable del iPod. Una vez que
aparezca el menú principal del iPod, vuelva a
conectar el iPod y reinícielo.
STOP
No hay canciones en la lista actual.
Seleccione una lista que contenga canciones.
NOT FOUND
No hay canciones relacionadas.
Transfiera canciones al iPod.
Aplicación
START UP APP
La aplicación no se ha iniciado aún.
Siga las instrucciones que aparecen en la
pantalla.
Pautas para el manejo
Discos y reproductor
Utilice únicamente discos que tengan uno de
estos dos logotipos:
Utilice discos de 12 cm.
Utilice sólo discos convencionales y completa-
mente circulares.
Información adicional
66
Apéndice
Información adicional
Es
Black plate (67,1)
Los siguientes tipos de discos no se pueden utili-
zar con esta unidad:
! DualDisc
! Discos de 8 cm: Si se utiliza este tipo de discos
con un adaptador, puede provocar el funciona-
miento defectuoso de la unidad.
! Discos con formas extrañas
! Discos que no sean CD
! Discos dañados, incluido discos que estén
partidos, desconchados o deformados
! Discos CD-R/RW que no se han finalizado
No toque la superficie grabada de los discos.
Cuando no utilice los discos, guárdelos en sus
cajas.
No fije etiquetas, no escriba ni aplique sustancias
químicas en la superficie de los discos.
Para limpiar un CD, pásele un paño suave desde
el centro hacia afuera.
La condensación puede afectar temporalmente al
rendimiento del reproductor. Deje de usarlo duran-
te una hora aproximadamente para que se adapte
a la temperatura más cálida. Además, si los dis-
cos tienen humedad, séquelos con un paño
suave.
Quizá no pueda reproducir algunos discos debido
a sus características, formato, programas graba-
dos, entorno de reproducción, condiciones de al-
macenamiento u otras causas.
Las vibraciones en las carreteras pueden inte-
rrumpir la reproducción de un disco.
Al usar discos de superficie imprimible para eti-
quetas, lea primero las instrucciones y las adver-
tencias de los discos. Es posible que algunos
discos no puedan insertarse ni expulsarse. La utili-
zación de este tipo de discos puede dañar el equi-
po.
No pegue etiquetas compradas por separado ni
otro tipo de material a los discos.
! Los discos podrían combarse y no podrán re-
producirse.
! Las etiquetas pueden despegarse durante la
reproducción, evitando la expulsión del disco y
causando de este modo daños en el equipo.
Dispositivo de almacenamiento
USB
No se admiten las conexiones a través de un con-
centrador USB.
No conecte ningún otro objeto que no sea un dis-
positivo de almacenamiento USB.
Cuando conduzca, fije el dispositivo de almacena-
miento USB firmemente. No deje caer el dispositi-
vo de almacenamiento USB al suelo, ya que
puede quedar atascado debajo del freno o del ace-
lerador.
Se pueden producir los siguientes problemas
según el dispositivo de almacenamiento USB que
se utilice.
! Las operaciones pueden variar.
! Es posible que no se reconozca el dispositivo
de almacenamiento.
! Puede que los archivos no se reproduzcan co-
rrectamente.
! El dispositivo puede causar interferencias al
escuchar la radio.
iPod
No deje el iPod en lugares expuestos a una tempe-
ratura elevada.
Cuando conduzca, fije el iPod firmemente. No
deje caer el iPod al suelo, ya que puede quedar
atascado debajo del freno o del acelerador.
Acerca de los ajustes del iPod
! Cuando el iPod está conectado, esta unidad
desactiva el ajuste EQ (ecualizador) del iPod
para mejorar la acústica; al desconectar el
iPod, el EQ retoma su valor original.
! No puede desactivar la Repetición del iPod
cuando utiliza esta unidad. La Repetición se
cambiará automáticamente a Todo cuando el
iPod esté conectado a esta unidad.
La unidad no mostrará el texto incompatible guar-
dado en el iPod.
Compatibilidad con audio
comprimido (disco, USB)
WMA
Extensión de archivo: .wma
Velocidad de grabación: de 48 kbps a 320 kbps
(CBR) y de 48 kbps a 384 kbps (VBR)
Frecuencia de muestreo: 32 kHz, 44,1 kHz, 48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream con vídeo: no compati-
ble
MP3
Extensión de archivo: .mp3
Velocidad de grabación: de 8 kbps a 320 kbps
(CBR), VBR
Frecuencia de muestreo: de 8 kHz a 48 kHz
(32 kHz, 44,1 kHz, 48 kHz para énfasis)
Versiones de etiqueta ID3 compatibles: 1.0, 1.1,
2.2, 2.3, 2.4 (la etiqueta ID3 versión 2.x tiene priori-
dad sobre la versión 1.x)
Lista de reproducción M3u: no compatible
MP3i (MP3 interactivo), mp3 PRO: no compatible
WAV
Extensión de archivo: .wav
Bits de cuantificación: 8 y 16 (LPCM), 4 (MS
ADPCM)
Frecuencia de muestreo: 16 kHz a 48 kHz (LPCM),
22,05 kHz y 44,1 kHz (MS ADPCM)
! No puede usar esta función con USB MTP.
Información complementaria
Solo se pueden visualizar los primeros 32 caracte-
res como nombre de archivo (incluida la exten-
sión) o nombre de carpeta.
Los textos en ruso que se visualizarán en esta uni-
dad se deben codificar con los siguientes conjun-
tos de caracteres:
! Unicode (UTF-8, UTF-16)
! Los conjuntos de caracteres distintos de Uni-
code que se usan en el entorno Windows y
que están ajustados en ruso en la configura-
ción de idiomas múltiples.
Español
Información adicional
67
Apéndice
Información adicional
Es
Black plate (68,1)
Esta unidad puede no funcionar correctamente,
según la aplicación utilizada para codificar archi-
vos WMA.
Puede producirse una pequeña demora cuando
se inicie la reproducción de archivos de audio que
contienen datos de imágenes o archivos de audio
almacenados en un dispositivo USB con numero-
sas jerarquías de carpetas.
Disco
Jerarquía de carpetas reproducibles: hasta ocho
niveles (una jerarquía práctica de carpetas tiene
menos de dos niveles).
Carpetas reproducibles: hasta 99
Archivos reproducibles: hasta 999
Sistema de archivos: ISO 9660 Nivel 1 y 2, Romeo,
Joliet
Reproducción multisesión: compatible
Transferencia de datos en formato Packet Write:
no compatible
Independientemente de la longitud de la seccio-
nes en blanco que haya entre las canciones de la
grabación original, los discos de audio comprimi-
dos se reproducirán con una breve pausa entre
cada canción.
Dispositivo de almacenamiento
USB
Jerarquía de carpetas reproducibles: hasta ocho
niveles (una jerarquía práctica de carpetas tiene
menos de dos niveles).
Carpetas reproducibles: hasta 500
Archivos reproducibles: hasta 15 000
Reproducción de archivos protegidos por dere-
chos de autor: no compatible
Dispositivo de almacenamiento USB particionado:
solo se puede reproducir la primera partición.
Puede producirse cierto retraso cuando se inicie
la reproducción de archivos de audio en un dispo-
sitivo de almacenamiento USB con numerosas je-
rarquías de carpetas.
PRECAUCIÓN
! Pioneer no garantiza la compatibilidad con
todos los dispositivos de almacenamiento
masivo USB y no se hace responsable de la
pérdida de los datos en los reproductores
multimedia, smartphones u otros dispositi-
vos, mientras se utilicen con este producto.
! No deje discos ni dispositivos de almacena-
miento USB en lugares expuestos a altas
temperaturas.
Compatibilidad con iPod
Esta unidad sólo es compatible con los modelos
de iPod que se muestran a continuación.
Fabricado para
! iPod touch (5.ª generación)
! iPod touch (4.ª generación)
! iPod touch (3.ª generación)
! iPod touch (2.ª generación)
! iPod touch (1.ª generación)
! iPod classic
! iPod con vídeo
! iPod nano (7.ª generación)
! iPod nano (6.ª generación)
! iPod nano (5.ª generación)
! iPod nano (4.ª generación)
! iPod nano (3.ª generación)
! iPod nano (2.ª generación)
! iPod nano (1.ª generación)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Según la generación o versión del iPod, es posible
que algunas funciones no estén disponibles.
Las funciones pueden variar según la versión de
software del iPod.
Los usuarios de iPod con conector Lightning debe-
rían usar el cable Lightning a USB (suministrado
con el iPod).
Los usuarios de iPod con el conector del Dock de-
berían utilizar CD-IU51. Para más información,
consulte a su proveedor.
Si desea más información sobre la compatibilidad
de archivos y formatos, consulte los manuales del
iPod.
Audiolibro, podcast: compatible
PRECAUCIÓN
Pioneer no asume ninguna responsabilidad por
la pérdida de datos en el iPod, incluso si la pér-
dida ocurre durante el uso de esta unidad.
Secuencia de archivos de audio
El usuario no puede asignar números de carpe-
ta ni especificar secuencias de reproducción
con esta unidad.
Ejemplo de una jerarquía
1
2
3
4
5
6
01
02
03
04
05
Nivel 1 Nivel 2 Nivel 3 Nivel 4
: carpeta
: archivo de audio
comprimido
01 a 05: número de
carpeta
1 a 6: secuencia
de reproducción
Disco
La secuencia de selección de carpetas u otras
operaciones pueden diferir, dependiendo del
software de codificación o escritura.
Dispositivo de almacenamiento
USB
La secuencia de reproducción es la misma que
la secuencia grabada en el dispositivo de alma-
cenamiento USB.
Para especificar la secuencia de reproducción,
se recomienda el siguiente método.
1 Cree un nombre del archivo que incluya nú-
meros que especifiquen la secuencia de re-
producción (p. ej., 001xxx.mp3 y 099yyy.mp3).
2 Coloque esos archivos en una carpeta.
3 Guarde la carpeta que contiene los archivos
en el dispositivo de almacenamiento USB.
Sin embargo, dependiendo del entorno del siste-
ma, tal vez no pueda especificar la secuencia de
reproducción.
Para reproductores de audio portátiles USB, la
secuencia es diferente y depende del reproduc-
tor.
Información adicional
68
Apéndice
Información adicional
Es
Black plate (69,1)
Tabla de caracteres rusos
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Visualización C: Carácter
Copyright y marcas registradas
MP3
La venta de este producto solo otorga una licen-
cia para su uso privado, no comercial. No otorga
ninguna licencia ni concede ningún derecho a
utilizar este producto en transmisiones comer-
ciales (es decir, lucrativas) en tiempo real (te-
rrestres, vía satélite, por cable y/o por cualquier
otro medio), transmisiones/streaming por Inter-
net, intranets u otras redes o en otros sistemas
de distribución de contenido electrónico, como
por ejemplo, aplicaciones de pago por escucha
(pay-audio) o audio bajo demanda (audio-on-de-
mand). Se necesita una licencia independiente
para su uso comercial. Para obtener más infor-
mación, visite
http://www.mp3licensing.com.
WMA
Windows Media es una marca registrada o una
marca de fábrica de Microsoft Corporation en
los Estados Unidos y/u otros países.
Este producto incluye tecnología propiedad de
Microsoft Corporation, y no se puede usar ni dis-
tribuir sin una licencia de Microsoft Licensing,
Inc.
iPod y iPhone
iPhone, iPod, iPod classic, iPod nano y iPod
touch son marcas comerciales de Apple Inc., re-
gistradas en los EE. UU. y en otros países.
Lightning es una marca comercial de Apple Inc.
Made for iPod y Made for iPhone significan
que un accesorio electrónico ha sido diseñado
para ser conectado específicamente a un iPod o
a un iPhone, respectivamente, y ha sido homolo-
gado por quien lo desarrolló para cumplir con
las normas de funcionamiento de Apple. Apple
no es responsable del funcionamiento de este
aparato ni de que cumpla con las normas de se-
guridad y reguladoras. Tenga presente que el
empleo de este accesorio con un iPod o iPhone
puede afectar la operación inalámbrica.
Androidä
Android es una marca comercial de Google Inc.
Especificaciones
Generales
Fuente de alimentación .... 14,4 V cc (10,8 V a 15,1 V per-
misible)
Sistema de derivación a tierra
................................... Tipo negativo
Consumo máximo de corriente
................................... 10,0 A
Dimensiones (An × Al × Pr):
DIN
Bastidor ........................... 178 mm × 100mm × 157mm
Cara anterior .................... 188 mm × 118mm × 25mm
D
Bastidor ........................... 178 mm × 100mm × 165mm
Cara anterior .................... 170 mm × 96 mm × 17mm
Peso ................................ 1,2 kg
Audio
Potencia de salida máxima
................................... 50 W × 4
70 W × 1/2 W (para altavoz de
subgraves)
Potencia de salida continua
................................... 22W × 4 (50Hz a 15000Hz,
5 % THD, 4 W de carga, ambos
canales activados)
Impedancia de carga ....... 4 W (4 W a8W permisibles)
Nivel de salida máxima del preamplificador
................................... 2,0V
Contorno de sonoridad ..... +10 dB (100 Hz), +6,5 dB
(10 kHz) (volumen: 30 dB)
Ecualizador (ecualizador gráfico de 5 bandas):
Frecuencia ....................... 80Hz/250 Hz/800 Hz/2,5 kHz/
8 kHz
Gama de ecualización ...... ±12 dB (paso de 2 dB )
Altavoz de subgraves (mono):
Frecuencia ....................... 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pendiente ........................ 12 dB/oct, 24 dB/oct
Ganancia ......................... +6dB a 24 dB
Fase ................................. Normal/Inversa
Reproductor de CD
Sistema ........................... Sistema de audio de discos
compactos
Discos utilizables ............. Disco compacto
Relación de señal a ruido
................................... 94dB (1kHz) (red IEC-A)
Número de canales .......... 2 (estéreo)
Formato de decodificación MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato de decodificación WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12
(audio 2 canales)
(Windows Media Player)
Formato de señal WAV ..... PCM lineal & MS ADPCM
(No comprimido)
USB
Especificación de la norma USB
................................... USB 2.0 velocidad máxima
Consumo máximo de corriente
................................... 1 A
Clase USB ....................... MCS (Clase de almacena-
miento masivo)
Sistema de archivos ......... FAT12, FAT16, FAT32
Formato de decodificación MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato de decodificación WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12
(audio 2 canales)
(Windows Media Player)
Formato de señal WAV ..... PCM lineal & MS ADPCM
(No comprimido)
Sintonizador de FM
Intervalo de frecuencias ... de 87,5 MHz a 108,0 MHz
Sensibilidad utilizable ...... 9 dBf (0,8 µV/75 W, mono,
señal/ruido: 30 dB)
Relación de señal a ruido
................................... 72dB (red IEC-A)
Sintonizador de MW
Intervalo de frecuencias ... de 531 kHz a 1 602 kHz
Sensibilidad utilizable ...... 25µV (señal/ruido: 20 dB)
Relación de señal a ruido
................................... 62dB (red IEC-A)
Sintonizador de LW
Intervalo de frecuencias ... de 153 kHz a 281 kHz
Sensibilidad utilizable ...... 28µV (señal/ruido: 20 dB)
Relación de señal a ruido
................................... 62dB (red IEC-A)
Nota
Las especificaciones y el diseño están sujetos a
modificaciones sin previo aviso.
Español
Información adicional
69
Apéndice
Información adicional
Es
Black plate (70,1)
Vielen Dank, dass Sie sich für dieses
PIONEER-Produkt entschieden haben
Bitte lesen Sie diese Anleitung vor der Verwen-
dung dieses Produkts zur Gewährleistung seiner
ordnungsgemäßen Verwendung durch. Lesen
und befolgen Sie dabei insbesondere die Hin-
weise WARNUNG und VORSICHT. Bewahren
Sie die Anleitung zur zukünftigen Bezugnahme si-
cher und griffbereit auf.
Mischen Sie dieses Produkt, wenn Sie es ent-
sorgen wollen, nicht mit gewöhnlichen Haus-
haltsabfällen. Es gibt ein getrenntes
Sammelsystem für gebrauchte elektronische
Produkte, über das die richtige Behandlung,
Rückgewinnung und Wiederverwertung
gemäß der bestehenden Gesetzgebung ge-
währleistet wird.
Privathaushalte in den Mitgliedstaaten der EU,
in der Schweiz und in Norwegen können ihre ge-
brauchten elektronischen Produkte kostenfrei
bei speziell dafür eingerichteten Sammelstellen
abgeben oder zu einem Fachhändler zurückbrin-
gen (sofern sie ein vergleichbares neues Produkt
kaufen).
In den Ländern, die hier nicht aufgeführt sind,
wenden Sie sich hinsichtlich der zu beachten-
den Entsorgungsweise bitte an die zuständige
Gemeindeverwaltung.
Auf diese Weise stellen Sie sicher, dass das zu
entsorgende Produkt der erforderlichen Verar-
beitung, Rückgewinnung und Wiederverwer-
tung zugeführt wird, und verhindern damit
potenziell negative Auswirkungen auf die Um-
welt sowie Gesundheitsschäden.
Zu diesem Gerät
Die Tuner-Frequenzen dieses Geräts sind für
Westeuropa, Asien, den Mittleren Osten, Afrika
und Ozeanien bestimmt. Der Gebrauch in ande-
ren Gebieten kann zu mangelhaftem Empfang
führen. Die RDS-Funktion (Radio-Datensystem)
funktioniert nur in Gebieten mit UKW-Sendern,
die RDS-Signale ausstrahlen.
Wichtig
Bitte tragen Sie die folgenden Informationen
in das dafür vorgesehene Formular auf der
Rückseite der Anleitung ein:
14-stellige Seriennummer (an der Unterseite
des Geräts angegeben)
Kaufdatum (Datum der Quittung)
Stempel des Händlers
Diese Informationen dienen als Eigentums-
nachweis. Im Fall eines Diebstahls teilen Sie
der Polizei die 14-stellige Seriennummer und
das Kaufdatum des Geräts mit.
Bewahren Sie die Bedienungsanleitung an
einem sicheren Ort auf.
WARNUNG
! Versuchen Sie nicht, dieses Produkt
selbst zu montieren oder zu warten. Wer-
den Montage- oder Wartungsarbeiten
des Produkts von Personen ohne Ausbil-
dung und Erfahrung hinsichtlich elekt-
ronischer Geräte und Fahrzeugzubehör
vorgenommen, kann dies gefährlich sein
und möglicherweise zu elektrischen
Schlägen, Verletzungen oder anderen
Gefahren führen.
! Bedienen Sie das Gerät niemals während der
Fahrt. Fahren Sie an den Straßenrand und
parken Sie Ihr Fahrzeug zuerst an einem si-
cheren Ort, bevor Sie die Bedienelemente
des Geräts bedienen.
VORSICHT
! Dieses Gerät darf nicht mit Flüssigkeiten in
Kontakt kommen. Dies könnte einen Strom-
schlag verursachen. Darüber hinaus kann
der Kontakt mit Flüssigkeit eine Beschädi-
gung des Geräts, Rauchentwicklung und
Überhitzung nach sich ziehen.
! Wählen Sie stets eine Lautstärke, bei der Sie
Umgebungsgeräusche noch deutlich wahr-
nehmen können.
! Setzen Sie dieses Gerät keiner Feuchtigkeit
aus.
VORSICHT
Bei diesem Gerät handelt es sich zwar um ein
Laserprodukt der Klasse 1, das entsprechend
dem Standard Sicherheit für Laserprodukte
IEC 60825-1:2007 klassifiziert ist.
LASER KLASSE 1
Im Problemfall
Sollte dieses Gerät nicht ordnungsgemäß funk-
tionieren, dann wenden Sie sich an Ihren Händ-
ler oder an die nächstgelegene PIONEER-
Kundendienststelle.
Bevor Sie beginnen
70
Abschnitt
Bevor Sie beginnen
De
01
Black plate (71,1)
Hauptgerät
1 2 4 5
8 9
7 a c6 b d
3
1 h (Auswurf)
2 iPod
3 1/
bis 6/
4 Disc-Ladeschacht
5 DISP
6 SRC/OFF
7 BAND/
(iPod-Steuerung)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(Zurück)/DIMMER (Dimmer)
b
(Liste)
c AUX-Eingang (3,5-mm-Stereoanschluss)
d USB-Anschluss
VORSICHT
Verwenden Sie für den Anschluss eines USB-
Speichergeräts ein optionales USB-Kabel von
Pioneer (CD-U50E), da direkt an diese Einheit
angeschlossene Zusatzgeräte hervorstehen und
eine Gefahr darstellen könnten.
Display-Anzeige
31 4 86
a
2 5 7 9
b
1 (Liste)
2
(iPod-Steuerung)
Die iPod-Funktionen dieses Geräts werden
über Ihren iPod bedient.
3 Unterinformationsbereich
4 TA (Verkehrsdurchsagen)
5 TP (Verkehrsprogramm-Identifizierung)
6
(Sound Retriever)
7 LOC (Lokal-Suchlaufabstimmung)
8
(Wiederholwiedergabe)
9
(zufällige Wiedergabe)
a
Hauptinformationsbereich
! Tuner: Frequenzband und Frequenz
! RDS: Programm-Service-Name, PTY-In-
formation und andere Textinformationen
! CD-Player, USB-Speichermedium und
iPod: verstrichene Wiedergabezeit und
Textinformationen
b
Erscheint, wenn eine untergeordnete Ord-
ner- oder Menüebene vorhanden ist.
Setup-Menü
1 Drehen Sie nach der Installation des Ge-
räts den Zündschalter auf EIN.
Die Angabe SET UP erscheint.
2 Drehen Sie M.C., um zu YES umzuschal-
ten.
# Wenn Sie das Gerät nicht innerhalb von 30 Se-
kunden bedienen, wird das Setup-Menü nicht ange-
zeigt.
# Wenn Sie es vorziehen, die Einstellungen nicht
jetzt vorzunehmen, drehen die den M.C.-Regler auf
NO.
3 Drücken Sie zur Auswahl M.C.
4 Befolgen Sie diese Schritte, um das Menü
einzurichten.
Sie müssen Ihre Auswahl bestätigen, um die
nächste Menüoption aufrufen zu können.
LANGUAGE (Spracheinstellung)
Das Gerät kann Textinformationen komprimierter
Audiodateien auch dann anzeigen, wenn sie auf
Englisch, Russisch oder Türkisch aufgezeichnet
wurden.
! Falls die für die Aufzeichnung verwendete
Sprache und die gewählte Spracheinstellung
nicht übereinstimmen, werden die Textinfor-
mationen ggf. nicht richtig angezeigt.
! Bestimmte Zeichen werden ggf. nicht ord-
nungsgemäß angezeigt.
1 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
ENG (Englisch)РУС (Russisch)TUR (Tür-
kisch)
2 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
CLOCK SET (Einstellen der Uhrzeit)
1 Drehen Sie M.C., um die Stunde einzustellen.
2 Drücken Sie auf M.C., um die Minuten auszu-
wählen.
3 Drehen Sie M.C., um die Minuten einzustellen.
4 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
FM STEP (UKW-Kanalraster)
Verwenden Sie FM STEP, um die UKW-Kanalraste-
roptionen (Suchschritteinstellungen) einzustellen.
1 Drehen Sie M.C., um die UKW-Kanalraster-
Funktion zu wählen.
100 (100 kHz)50 (50 kHz)
2 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
Die Angabe QUIT erscheint.
! Bei der manuellen Abstimmung ist das Kanal-
raster auf 50 kHz fest eingestellt.
! Wenn AF und TA deaktiviert sind, ist für das
Suchlauf-Kanalraster 50 kHz fest eingestellt,
selbst wenn 100 ausgewählt ist.
5 Um die Einstellungen abzuschließen, dre-
hen Sie M.C., um zu YES zu wechseln.
# Möchten Sie Ihre Einstellungen wieder ändern,
drehen Sie M.C.,umNO auszuwählen.
6 Drücken Sie zur Auswahl M.C.
Hinweise
! Sie können die Menüoptionen über das Sys-
temmenü und Grundmenü einstellen. Für
Details zu den Einstellungen siehe System-
menü auf Seite 78 und Grundmenü auf Seite
78.
! Das Einstellmenü kann durch Drücken von
SRC/OFF abgebrochen werden.
Grundlegende Bedienvorgänge
Einschalten des Geräts
1 Drücken Sie die Taste SRC/OFF, um das Gerät
einzuschalten.
Ausschalten des Geräts
1 Drücken und halten Sie SRC/OFF gedrückt, bis
sich das Gerät ausschaltet.
Deutsch
Gebrauch dieses Geräts
71
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (72,1)
Wählen einer Programmquelle
1 Drücken Sie SRC/OFF, um zwischen den fol-
genden Optionen umzuschalten:
RADIOCDUSB/iPodAPP (Anwendung)
AUX
! USB MTP wird angezeigt, während die MTP-
Verbindung hergestellt ist.
! Wenn ein iPod angeschlossen und eine ande-
re Quelle als iPod gewählt ist, können Sie
durch Drücken von iPod zu iPod wechseln.
Regeln der Lautstärke
1 Drehen Sie M.C., um die Lautstärke anzupas-
sen.
Hinweis
Wenn das blau/weiße Kabel dieses Geräts an
die Steuerklemme des Automatikantennenrelais
des Kraftfahrzeugs angeschlossen wird, wird die
Antenne ausgefahren, sobald das Gerät einge-
schaltet wird. Zum Einfahren der Antenne schal-
ten Sie die Programmquelle aus.
Häufig verwendete
Menüschritte
Zurückschalten zur vorherigen Anzeige
Zum Zurückschalten zur vorherigen Liste (bzw.
zum übergeordneten Ordner)
1 Drücken Sie
/DIMMER.
Zurückschalten zur normalen Anzeige
Beenden des Hauptmenüs
1 Drücken Sie BAND/
.
Zurückschalten zur normalen Anzeige von der
Liste
1 Drücken Sie BAND/
.
Radio
Grundlegende Bedie nvorgänge
Wahl eines Bands (Wellenbereich)
1 Drücken Sie BAND/
, bis der gewünschte
Wellenbereich angezeigt wird (FM1, FM2,
FM3 für UKW bzw. MW/LW).
Wechseln der voreingestellten Sender
1 Drücken Sie c oder d.
! Wählen Sie PCH (voreingesteller Kanal) unter
SEEK, um diese Funktion verwenden zu kön-
nen.
Manuelle (schrittweise) Abstimmung
1 Drücken Sie c oder d.
! Wählen Sie MAN (manuelle Abstimmung)
unter SEEK, um diese Funktion verwenden zu
können.
Suchlauf
1 Drücken und halten Sie c oder d gedrückt
und lassen Sie die Taste dann wieder los.
Durch kurzes Drücken von c oder d kann die
Suchlaufabstimmung aufgehoben werden.
Durch Drücken und Gedrückthalten von c
oder d können Sender übersprungen werden.
Die Suchlaufabstimmung beginnt, sobald c
bzw. d losgelassen wird.
Hinweise
! Details zu SEEK finden Sie unter SEEK (Ein-
stellen der linken/rechten Tasten) auf Seite 73.
! Der Alternativfrequenz-Suchlauf (AF) dieses
Geräts kann ein- und ausgeschaltet werden.
Für den normalen Abstimmbetrieb sollte AF
ausgeschaltet sein (siehe AF (Alternativfre-
quenz-Suchlauf) auf Seite 73).
Speichern und Abrufen von
Radiostationen für jedes Band
Verwendung der Stationstasten
1 Zum Speichern: Drücken Sie eine der
Stationstasten (1/
bis 6/ ) und halten
diese gedrückt, bis die Stationsnummer nicht
mehr blinkt.
2 Zum Abrufen: Drücken Sie eine der
Stationstasten (1/
bis 6/ ).
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! FREQUENCY (Programm-Service-Name
oder Frequenz)
! BRDCST INFO (Programm-Service-Name/
PTY-Information)
! CLOCK (Programmquellname und Uhr)
Hinweise
! Wenn der Programm-Service-Name nicht
unter FREQUENCY abgerufen werden kann,
wird stattdessen die Sendefrequenz ange-
zeigt. Der Programm-Service-Name wird bei
einer Erkennung angezeigt.
! Je nach dem Band kann die Textinformation
geändert werden.
! Welche Textinformationen geändert werden
können, hängt vom Bereich ab.
Gebrauch der Programmtyp-
Funktionen (PTY)
Sie können einen Sender anhand eines Pro-
grammtyps (PTY) abstimmen.
Suchen nach RDS-Stationen anhand eines Pro-
grammtyps
1 Drücken Sie auf
(Liste).
2 Drehen Sie M.C., um einen Programmtyp zu
wählen.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Drücken Sie M.C., um die Suche zu starten.
Das Gerät sucht nach einer Station, die ein
Programm des gewählten Typs ausstrahlt.
Wenn eine solche Station gefunden wird, wird
deren Stationsname angezeigt.
! Zum Aufheben des Suchlaufs drücken Sie
M.C. erneut.
! Das Programm mancher Sender kann von
dem tatsächlich übertragenen Programm-
typ (PTY) abweichen.
! Wird kein Sender gefunden, der ein Pro-
gramm des gewählten Typs ausstrahlt,
dann erscheint zwei Sekunden lang NOT
FOUND und der Tuner schaltet auf die ur-
sprüngliche Station zurück.
PTY-Liste
Detaillierte Informationen zur PTY-Liste finden
Sie auf folgender Website:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die gewünschte
Funktion zu wählen.
Nach der Auswahl können die folgenden Funk-
tionen angepasst werden.
Gebrauch dieses Geräts
72
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (73,1)
# Wenn das MW/LW-Band gewählt ist, stehen nur
BSM, LOCAL und SEEK zur Verfügung.
FM SETTING (Einstellungen für die UKW-Klang-
qualität)
Die Klangqualität kann so eingestellt werden,
dass sie den Sendesignalbedingungen des UKW-
Frequenzbereichsignals entspricht.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
! STANDARD Dies ist die Standardeinstel-
lung.
! HI-FI Diese Einstellung sollte verwendet
werden, um vorzugsweise eine hohe Ste-
reo-Klangqualität zu verwenden.
! STABLE Diese Einstellung sollte verwen-
det werden, um vorzugsweise einen Mono-
Klang mit geringem Rauschen zu verwen-
den.
BSM (Best-Sender-Memory)
BSM (Best-Sender-Memory) speichert die sechs
stärksten Sender automatisch in der Reihenfolge
ihrer Signalstärke.
1 Drücken Sie M.C., um BSM einzuschalten.
Zum Abbrechen des Speichervorgangs drü-
cken Sie M.C. erneut.
REGIONAL (Regional)
Bei Verwendung des Alternativfrequenz-Suchlaufs
beschränkt die Regionalfunktion die Auswahl auf
Sender, die regionale Programme ausstrahlen.
1 Drücken Sie M.C., um die Regionalfunktion
ein- oder auszuschalten.
LOCAL (Lokal-Suchlaufabstimmung)
Mit der Lokal-Suchlaufabstimmung wird nur nach
Stationen mit ausreichender Signalstärke für
einen guten Empfang gesucht.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
UKW: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
Bei Auswahl der höchsten Stufe werden nur
die stärksten Sender empfangen, während bei
Auswahl der niedrigeren Stufen schwächere
Sender zugelassen werden.
TA (Verkehrsdurchsagebereitschaft)
1 Drücken Sie M.C., um die Verkehrsdurchsage-
bereitschaft ein- oder auszuschalten.
AF (Alternativfrequenz-Suchlauf)
1 Drücken Sie M.C., um den Alternativfrequenz-
Suchlauf ein- oder auszuschalten.
NEWS (Nachrichtenunterbrechung)
1 Drücken Sie M.C., um die Nachrichtenfunk-
tion ein- oder auszuschalten.
SEEK (Einstellen der linken/rechten Tasten)
Sie können den linken und rechten Tasten des
Gerät eine Funktion zuweisen.
Wählen Sie MAN (manuelle Abstimmung) zur ma-
nuellen Abstimmung oder PCH (vorprogrammier-
ter Kanal) zum Umschalten zwischen den
vorprogrammierten Kanälen.
1 Drücken Sie M.C.,umMAN oder PCH zu wäh-
len.
CD/CD-R/CD-RW-Discs und
USB-Speichermedien
MTP-Verbindung
MTP-kompatible Android-Geräte (mit Android-
Betriebssystem 4.0 oder höher) können über
eine MTP-Verbindung unter Verwendung einer
USB-Quelle verbunden werden. Um ein
Android-Gerät anzuschließen, verwenden Sie
das dem Gerät beiliegende Kabel.
Hinweis
Diese Funktion ist nicht mit WAV kompatibel.
Grundlegende Bedie nvorgänge
Wiedergabe einer CD/CD-R/CD-RW-Disc
1 Legen Sie die Disc mit der Etikettenseite nach
oben in den Ladeschacht.
Auswerfen einer CD/CD-R/CD-RW-Disc
1 Drücken Sie auf h.
Wiedergabe von Musiktiteln eines USB-Speicher-
mediums
1 Öffnen Sie die Abdeckung des USB-Anschlus-
ses.
2 Schließen Sie das USB-Speichermedium über
ein USB-Kabel an.
Wiedergabe der Musiktitel auf einem USB-Spei-
chermedium abbrechen
1 Das USB-Speichermedium kann jederzeit vom
Gerät getrennt werden.
Wählen eines Ordners
1 Drücken Sie 1/
oder 2/ .
Wahl eines Titels
1 Drücken Sie c oder d.
Schnellvorlauf bzw. -rücklauf
1 Drücken und halten Sie c oder d gedrückt.
! Bei der Wiedergabe von Dateien im kompri-
mierten Audio-Format wird beim schnellen
Vor- und Rücklauf kein Ton ausgegeben.
Rückkehr zum Stammordner
1 Drücken und halten Sie BAND/
gedrückt.
Umschalten zwischen dem komprimierten Audio-
format und CD-DA
1 Drücken Sie BAND/
.
Umschalten zwischen Wiedergabespeichergerä-
ten
Sie können zwischen Wiedergabespeichereinhei-
ten eines USB-Speichermediums wechseln, wel-
ches über mehrere Massenspeicherklasse
kompatible Einheiten verfügt.
1 Drücken Sie BAND/
.
! Sie können zwischen bis zu 32 verschiedenen
Speichergeräten wechseln.
Hinweis
Trennen Sie USB-Speichermedien bei Nichtver-
wendung von diesem Gerät ab.
Deutsch
Gebrauch dieses Geräts
73
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (74,1)
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
CD-DA
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
CD-TEXT
! TRACK INFO (Titelname/Titel-Künstler/
Disc-Titel)
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
MP3/WMA/WAV
! TRACK INFO (Titelname/Künstlername/Al-
bumtitel)
! FILE INFO (Dateiname/Ordnername)
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
Auswählen und Wiedergeben von
Dateien/Titeln der Namensliste
1 Drücken Sie , um in den Datei-/Titellis-
tenmodus umzuschalten.
2 Verwenden Sie M.C., um den Namen der
gewünschten Datei (bzw. des gewünschten
Ordners) zu wählen.
Auswählen einer Datei oder eines Ordners
1 Drehen Sie M.C.
Wiedergabe
1 Drücken Sie nach Auswahl einer Datei oder
eines Titels auf M.C.
Anzeige einer Liste der Dateien (oder Ordner) im
gewählten Ordner
1 Drücken Sie nach Auswahl eines Ordners auf
M.C.
Wiedergabe eines Musiktitels im gewählten Ord-
ner
1 Drücken und halten Sie M.C. nach Auswahl
des Ordners gedrückt.
Bedienvorgänge mit speziellen
Tasten
Wählen eines Wiederholbereichs
1 Drücken Sie 6/
, um zwischen den folgen-
den Optionen umzuschalten:
CD/CD-R/CD-RW-Discs
! ALL Wiederholung aller Titel
! ONE Wiederholung des momentanen Ti-
tels
! FLD Wiederholung des momentanen
Ordners
USB-Speichermedium
! ALL Wiederholung aller Dateien
! ONE Wiederholung der momentanen
Datei
! FLD Wiederholung des momentanen
Ordners
Abspielen von Titeln in zufälliger Reihenfolge
1 Drücken Sie 5/
, um die zufallsgesteuerte
Wiedergabe ein- oder auszuschalten.
Die Titel innerhalb des gewählten Wiederhol-
bereichs werden in einer zufälligen Reihenfol-
ge gespielt.
! Um Titel während der zufälligen Wiedergabe
zu ändern, drücken Sie auf d, um zum nächs-
ten Titel zu wechseln. Durch Drücken von c
wird die Wiedergabe des aktuellen Titels von
seinem Anfang neu gestartet.
Pausieren der Wiedergabe
1 Drücken Sie 4/PAUSE, um die Wiedergabe an-
zuhalten oder fortzusetzen.
Verbessern der komprimierten Audiodaten und
Wiederherstellen eines reichen Klangbild (Sound
Retriever)
1 Drücken Sie 3/S.Rtrv, um zwischen den fol-
genden Optionen umzuschalten:
12OFF (Aus)
1 wirkt bei einem niedrigen und 2 bei einem
hohen Kompressionsfaktor.
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
Nach der Auswahl kann die unten stehende
Funktion angepasst werden.
S.RTRV (Sound Retriever)
Verbessert komprimierte Audiodaten und stellt ein
reiches Klangbild wieder her.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
Für detaillierte Informationen hierzu siehe Ver-
bessern der komprimierten Audiodaten und Wie-
derherstellen eines reichen Klangbild (Sound
Retriever) auf Seite 74.
iPod
Grundlegende Bedie nvorgänge
Wiedergabe von Musiktiteln eines iPods
1 Öffnen Sie die Abdeckung des USB-Anschlus-
ses.
2 Schließen Sie einen iPod an den USB-Eingang
an.
Die Wiedergabe erfolgt automatisch.
Wahl eines Musiktitels (Kapitels)
1 Drücken Sie c oder d.
Auswählen eines Albums
1 Drücken Sie 1/
oder 2/ .
Schnellvorlauf bzw. -rücklauf
1 Drücken und halten Sie c oder d gedrückt.
Hinweise
! Der iPod kann nicht ein- bzw. ausgeschaltet
werden, wenn der Steuermodus
CTRL AUDIO gewählt wurde.
! Trennen Sie die Kopfhörer vom iPod, bevor
Sie ihn mit diesem Gerät verbinden.
! Wenn die Zündung des Wagens ausgeschal-
tet wird, schaltet sich der iPod nach etwa
zwei Minuten aus.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! TRACK INFO (Titelname/Künstlername/Al-
bumtitel)
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
Gebrauch dieses Geräts
74
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (75,1)
Suchen nach Musiktiteln
1 Drücken Sie , um zum Hauptmenü der
Listensuche zu wechseln.
2 Verwenden Sie M.C., um eine Kategorie
bzw. einen Musiktitel auszuwählen.
Musiktitel- oder Kategorienname ändern
1 Drehen Sie M.C.
SpiellistenKünstlerAlbenMusiktitel
PodcastsMusik-GenresKomponisten
Hörbücher
Wiedergabe
1 Drücken Sie nach Auswahl eines Musiktitels
auf M.C.
Wiedergabe einer Musiktitelliste der ausgewähl-
ten Kategorie
1 Drücken Sie nach Auswahl einer Kategorie
auf M.C.
Wiedergabe eines Musiktitels der gewählten Kate-
gorie
1 Drücken und halten Sie M.C. nach Auswahl
der Kategorie gedrückt.
Alphabetische Listensuche
1 Sobald die Liste der gewählten Kategorie an-
gezeigt wird, drücken Sie die Taste
,umin
den alphabetischen Suchmodus umzuschal-
ten.
! Durch zweimaliges Drehen von M.C. kann
in den alphabetischen Suchmodus ge-
wechselt werden.
2 Drehen Sie M.C., um einen Buchstaben zu
wählen.
3 Drücken Sie M.C., um eine alphabetisch sor-
tierte Liste anzuzeigen.
! Zum Abbrechen des Suchvorgangs drücken
Sie auf
/DIMMER.
Hinweise
! Sie können Spiellisten mithilfe einer auf un-
serer Website erhältlichen Computer-Anwen-
dung (MusicSphere) erstellen.
! Die mithilfe dieser Computer-Anwendung
(MusicSphere) erstellten Spiellisten werden
abgekürzt angezeigt.
Bedienvorgänge mit speziellen
Tasten
Wählen eines Wiederholbereichs
1 Drücken Sie 6/
, um zwischen den folgen-
den Optionen umzuschalten:
! ONE Wiederholung des momentanen
Musiktitels
! ALL Wiederholung aller Musiktitel in der
gewählten Liste
! Wenn als Steuermodus CTRL iPod gewählt
wurde, ist der Wiederholbereich der gleiche
wie im angeschlossenen iPod.
Auswählen des zufälligen Wiederholbereichs
(Shuffle)
1 Drücken Sie 5/
, um zwischen den folgen-
den Optionen umzuschalten:
! SNG Zufallsgesteuerte Wiedergabe der
Musiktitel der gewählten Liste
! ALB Wiedergabe in der richtigen Reihen-
folge der Musiktitel in einem nach dem Zu-
fallsprinzip gewählten Album
! OFF Kein Abspielen in zufälliger Reihen-
folge
Abspielen aller Musiktitel in zufälliger Reihenfolge
(Shuffle All)
1 Drücken und halten Sie 5/
gedrückt, um
die Funktion Shuffle All (zufällige Wiederga-
be aller Titel) einzuschalten.
! Zum Ausschalten der Funktion Shuffle All
wählen Sie OFF im Shuffle-Modus. Für detail-
lierte Informationen hierzu siehe Auswählen
des zufälligen Wiederholbereichs (Shuffle) auf
Seite 75.
Pausieren der Wiedergabe
1 Drücken Sie 4/PAUSE, um die Wiedergabe an-
zuhalten oder fortzusetzen.
Verbessern der komprimierten Audiodaten und
Wiederherstellen eines reichen Klangbild (Sound
Retriever)
1 Drücken Sie 3/S.Rtrv, um zwischen den fol-
genden Optionen umzuschalten:
12OFF (Aus)
1 wirkt bei einem niedrigen und 2 bei einem
hohen Kompressionsfaktor.
Wiedergabe von Musiktiteln mit
Bezug zum momentan
spielenden Titel
Es können Musiktitel der folgenden Listen abge-
spielt werden:
Albumliste des momentan spielenden Künst-
lers
Musiktitelliste des momentan spielenden Al-
bums
Albumliste des momentan spielenden Musik-
Genres
1 Drücken und halten Sie
gedrückt, um
in den Modus der verknüpften Wiedergabe
umzuschalten.
2 Drehen Sie M.C., um den Modus zu wech-
seln, und drücken Sie ihn, um den angezeig-
ten Modus zu wählen.
! ARTIST Wiedergabe eines Albums des mo-
mentan spielenden Künstlers
! ALBUM Wiedergabe eines Musiktitels
eines Albums des momentan spielenden
Künstlers
! GENRE Wiedergabe eines Albums aus dem
Genre des momentan spielenden Künstlers
Der ausgewählte Musiktitel bzw. das ausgewähl-
te Album wird nach dem gerade spielenden Mu-
siktitel wiedergegeben.
Hinweise
! Die Wiedergabe des ausgewählten Musikti-
tels/Albums wird ggf. abgebrochen, wenn
Sie eine andere Funktion als die Verbin-
dungssuche (wie z. B. Schnellvorlauf oder
-rücklauf) wählen.
! Je nach dem für die Wiedergabe gewählten
Musiktitel können das Ende des momentan
spielenden Musiktitels und der Anfang des
ausgewählten Musiktitels/Albums abge-
schnitten werden.
Verwenden der iPod-Funktionen
dieses Geräts über den iPod
Die iPod-Funktionen dieses Geräts können über
den angeschlossenen iPod gesteuert werden.
CTRL iPod ist nicht mit den folgenden iPod-Mo-
dellen kompatibel:
! iPod nano der 1. Generation
! iPod mit Videos
% Drücken Sie auf BAND/
, um in den
Funktionssteuermodus zu wechseln.
! CTRL iPod Die iPod-Funktionen dieses Ge-
räts können über den angeschlossenen iPod
bedient werden.
! CTRL AUDIO Die iPod-Funktionen dieses
Geräts können über das Gerät gesteuert wer-
den.
Der Steuermodus kann auch durch Drücken auf
iPod geändert werden.
Hinweise
! Wenn Sie den Steuermodus auf CTRL iPod
umschalten, wird die Musiktitelwiedergabe
unterbrochen. Verwenden Sie den iPod, um
mit der Wiedergabe fortzufahren.
! Selbst wenn CTRL iPod als Steuermodus ge-
wählt wurde, können die folgenden Vorgänge
direkt über dieses Gerät vorgenommen wer-
den:
Pause
Schnellvorlauf/-rücklauf
Deutsch
Gebrauch dieses Geräts
75
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (76,1)
Wahl eines Musiktitels (Kapitels)
! Die Lautstärke kann nur über das Hauptgerät
angepasst werden.
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die gewünschte
Funktion zu wählen.
Nach der Auswahl können die folgenden Funk-
tionen angepasst werden.
! AUDIO BOOK steht nicht zur Verfügung,
wenn im Steuermodus CTRL iPod gewählt
wurde. Für detaillierte Informationen hierzu
siehe Verwenden der iPod-Funktionen dieses
Geräts über den iPod auf Seite 75.
AUDIO BOOK (Hörbuch-Abspielgeschwindigkeit)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die von Ihnen bevor zugte
Einstellung zu wählen.
! FASTER Schnellere Wiedergabe als nor-
male Wiedergabegeschwindigkeit
! NORMAL Normale Wiedergabege-
schwindigkeit
! SLOWER Langsamere Wiedergabe als
normale Wiedergabegeschwindigkeit
S.RTRV (Sound Retriever)
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
Für detaillierte Informationen hierzu siehe Ver-
bessern der komprimierten Audiodaten und Wie-
derherstellen eines reichen Klangbild (Sound
Retriever) auf Seite 75.
Arbeiten mit Anwendungen
angeschlossener Geräte
Dieses Gerät können Sie zur Streaming-Wieder-
gabe und zum Steuern von Titeln in iPhone-An-
wendungen oder nur für die Streaming-
Wiedergabe verwenden.
Wichtig
Die Verwendung von Apps von Dritten kann
eventuell die Angabe personenbezogener
Daten nach sich ziehen oder notwendig ma-
chen entweder durch das Eröffnen eines Be-
nutzerkontos o. Ä. und für bestimmte
Anwendungen die Angabe von Geolokations-
daten.
ALLE APPS VON DRITTEN UNTERLIEGEN
DER ALLEINIGEN VERANTWORTUNG DER
ANBIETER EINSCHLIESSLICH UND OHNE
EINSCHRÄNKUNG DEM SAMMELN UND SI-
CHERN DER ANWENDERDATEN UND DA-
TENSCHUTZMASSNAHMEN. DURCH
ZUGRIFF AUF APPS VON DRITTEN ERKLÄ-
REN SIE SICH MIT DEN NUTZUNGSBEDIN-
GUNGEN UND DATENSCHUTZRICHTLINIEN
DER JEWEILIGEN ANBIETER EINVERSTAN-
DEN. WENN SIE DEN NUTZUNGSBEDIN-
GUNGEN UND RICHTLINIEN EINES
ANBIETERS ODER DER VERWENDUNG VON
GEOLOKATIONSDATEN, WO ZUTREFFEND,
NICHT ZUSTIMMEN, DANN SEHEN SIE VON
DER VERWENDUNG VON APPS VON DRIT-
TEN AB.
Informationen zur Kompatibilität
von angeschlossenen Geräten
Im Folgenden finden Sie detaillierte Informatio-
nen über die erforderlichen Anschlüsse, um die
Anwendung für das iPhone auf diesem Gerät
verwenden zu können.
Für iPhone-Anwender
! Diese Funktion ist mit dem iPhone und dem
iPod touch kompatibel.
! Das Gerät läuft unter dem iOS-Betriebssys-
tem 5.0 oder höher.
Hinweise
! Besuchen Sie unsere Website, um eine Liste
der unterstützten iPhone-Anwendungen für
dieses Gerät zu erhalten.
! Pioneer übernimmt keine Haftung für jegli-
che von inkorrekten oder fehlerhaften app-
basierten Inhalten verursachte Probleme.
! Inhalt und Funktionalität der unterstützten
Anwendungen liegen in der Verantwortlich-
keit der App-Anbieter.
Einrichtverfahren für iPhone-
Anwender
1 Schließen Sie ein iPhone an den USB-Ein-
gang an.
2 Ändern Sie die Quelle zu APP.
3 Starten Sie die Anwendung auf dem
iPhone, und beginnen Sie mit der Wiederga-
be.
Grundlegende Bedie nvorgänge
Wahl eines Titels
1 Drücken Sie c oder d.
Schnellvorlauf bzw. -rücklauf
1 Drücken und halten Sie c oder d gedrückt.
Pausieren der Wiedergabe
1 Drücken Sie BAND/
, um die Wiedergabe an-
zuhalten oder fortzusetzen.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! TRACK INFO (Titelname/Künstlername/Al-
bumtitel)
! APP NAME (Anwendungsname)
! ELAPSED TIME (Wiedergabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die gewünschte
Funktion zu wählen.
Nach der Auswahl können die folgenden Funk-
tionen angepasst werden.
PAUSE (Pause)
1 Drücken Sie M.C., um die Wiedergabe anzu-
halten oder fortzusetzen.
S.RTRV (Sound Retriever)
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
12OFF (Aus)
1 wirkt bei einem niedrigen und 2 bei einem
hohen Kompressionsfaktor.
Audio-Einstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
Gebrauch dieses Geräts
76
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (77,1)
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf AUDIO, um
die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die gewünschte
Audio-Funktion zu wählen.
Nach der Auswahl können die folgenden Audio-
funktionen angepasst werden.
! FADER steht nicht zur Verfügung, wenn in
SP-P/O MODE die Option SUB.W/SUB.W ge-
wählt wurde. Für detaillierte Informationen
hierzu siehe SP-P/O MODE (Heckausgang-
und Preout-Einstellungen) auf Seite 78.
! SUB.W und SUB.W CTRL stehen nicht zur
Verfügung, wenn in SP-P/O MODE die Op-
tion REAR/REAR gewählt wurde. Für Details
siehe SP-P/O MODE (Heckausgang- und
Preout-Einstellungen) auf Seite 78.
! SUB.W CTRL steht nicht zur Verfügung,
wenn in OFF die Option SUB.W gewählt
wurde. Für Details siehe SUB.W (Subwoofer
Ein/Aus) auf Seite 77.
! SLA steht nicht zur Verfügung, wenn als
Quelle FM gewählt wurde.
FADER (Überblendeinstellung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Front-/Heck-Lautspre-
cherbalance einzustellen.
BALANCE (Balance-Einstellung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Links-/Rechts-Laut-
sprecherbalance einzustellen.
EQ SETTING (Equalizer-Abruf)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um einen Equalizer zu wäh-
len.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
Das Equalizer-Band und der Equalizer-Pegel
können individuell angepasst werden, wenn
CUSTOM1 oder CUSTOM2 gewählt ist.
Schließen Sie bei Wahl von CUSTOM1 oder
CUSTOM2 den unten genannten Vorgang ab.
Kehren Sie bei Wahl einer anderen Option
durch Drücken auf M.C. zur vorherigen Anzei-
ge zurück.
! CUSTOM1 kann für jede Quelle separat
eingestellt werden. USB, iPod und APP
sind hingegen automatisch auf die gleiche
Einstellung gesetzt.
! Bei CUSTOM2 handelt es sich um eine ge-
meinsam verwendete Einstellung für alle
Quellen.
3 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
4 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
EqualizerbandEqualizer-Pegel
5 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Equalizer-Band: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizer-Pegel: +6 bis 6
LOUDNESS (Loudness)
Die Loudness-Funktion kompensiert die vermin-
derte Wahrnehmung von niedrigen und hohen
Frequenzen bei geringer Lautstärke.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
OFF (Aus)LOW (Niedrig)MID (Mittel)HI
(Hoch)
SUB.W (Subwoofer Ein/Aus)
Dieses Gerät ist mit einem Subwoofer-Ausgang
ausgestattet, der ein- und ausgeschaltet werden
kann.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
NOR (Normalphase)REV (Gegenphase)
OFF (Subwoofer Aus)
SUB.W CTRL (Subwoofer-Einstellungen)
Vom Subwoofer werden nur solche Frequenzen
ausgegeben, die unter dem gewählten Bereich lie-
gen.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
TrennfrequenzAusgabepegelPegel der
Steilheit
Einstellbare Werte blinken.
3 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Trennfrequenz: 50HZ63HZ80HZ100HZ
125HZ160HZ200HZ
Ausgangspegel: 24 bis +6
Pegel der Steilheit: 12 24
BASS BOOST (Bassverstärkung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um den gewünschten Pegel
zu wählen.
Während der Erhöhung bzw. Verminderung
des Pegels wird 0 bis +6 angezeigt.
HPF SETTING (Hochpassfilter-Anpassung)
Verwenden Sie diese Funktion, um nur Hochfre-
quenztöne anzuhören. Nur Frequenzen, die höher
als die Trennfrequenz des Hochpassfilters (HPF)
sind, werden über die Lautsprecher ausgegeben.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
TrennfrequenzPegel der Steilheit
3 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Trennfrequenz: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Pegel der Steilheit: 12 24
SLA (Programmquellen-Pegeleinstellung)
Diese Funktion verhindert, dass sich die Lautstär-
ke beim Wechseln der Programmquelle drama-
tisch ändert.
! Die Einstellungen basieren auf der UKW-Laut-
stärke, die unverändert bleibt.
! Der MW/LW-Lautstärkepegel kann ebenfalls
mit dieser Funktion eingestellt werden.
! USB, iPod und APP sind automatisch auf die
gleiche Einstellung gesetzt.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Lautstärke für die
Programmquelle einzustellen.
Einstellbereich: +4 bis 4
Deutsch
Gebrauch dieses Geräts
77
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (78,1)
Systemmenü
Wichtig
Die Funktion PW SAVE (Energiesparmodus)
wird deaktiviert, wenn die Fahrzeugbatterie ab-
geklemmt wird und muss neu aktiviert werden,
sobald die Batterie wieder angeschlossen wird.
Wenn PW SAVE (Energiesparmodus) deaktiviert
ist, kann das Gerät je nach Anschlussart Batte-
rieleistung in Anspruch nehmen, sollte die Zün-
dung des Fahrzeugs über keine ACC-Position
(Zubehörposition) verfügen.
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die Systemmenü-
Funktion zu wählen.
Nach der Auswahl können die folgenden Sys-
temmenüfunktionen angepasst werden.
LANGUAGE (Spracheinstellung)
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
ENG (Englisch)РУС (Russisch)TUR (Tür-
kisch)
CLOCK SET (Einstellen der Uhrzeit)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um den Teil der Zeitanzeige
zu wählen, der eingestellt werden soll.
StundenMinuten
3 Drehen Sie M.C., um die Uhrzeit einzustellen.
12H/24H (Uhrzeitformat)
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
12H (12-Stunden-Uhr)24H (24-Stunden-Uhr)
AUTO PI (Automatische PI-Suche)
Das Gerät kann selbst bei einem Stationsabruf au-
tomatisch nach einer anderen Station mit dersel-
ben Programmierung suchen.
1 Drücken Sie M.C., um den Auto-PI-Suchlauf
ein- oder auszuschalten.
AUX (Zusatzeingang)
Aktivieren Sie diese Einstellung, wenn ein zusätzli-
ches, mit diesem Gerät verbundenes Gerät ver-
wendet wird.
1 Drücken Sie M.C.,umAUX ein- oder auszu-
schalten.
DIMMER (Dimmer)
1 Drücken Sie M.C., um den Dimmer ein- bzw.
auszuschalten.
! Sie können die Dimmer-Einstellung auch
durch Drücken und Halten von
/DIMMER
ändern.
MUTE MODE (Stummschaltung)
Die Klangwiedergabe dieses Geräts wird automa-
tisch stummgeschaltet oder gedämpft, wenn das
Signal eines Geräts mit Stummschaltung empfan-
gen wird.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
! MUTE Stummschaltung
! 20dB ATT Dämpfung (20dB ATT hat eine
stärkere Wirkung als 10dB ATT)
! 10dB ATT Dämpfung
PW SAVE (Energiesparmodus)
Wenn Sie diese Funktion einschalten, reduzieren
Sie den Verbrauch von Batterieleistung.
! Bei aktiviertem Energiesparmodus kann nur
die Programmquelle eingeschaltet werden.
1 Drücken Sie M.C., um den Energiesparmodus
ein- oder auszuschalten.
Grundmenü
1 Drücken und halten Sie SRC/OFF ge-
drückt, bis sich das Gerät ausschaltet.
2 Drücken und halten Sie SRC/OFF ge-
drückt, bis das Hauptmenü im Display er-
scheint.
3 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf INITIAL, um
die angezeigte Option zu wählen.
4 Drehen Sie M.C., um die Grundmenü-
Funktion zu wählen.
Nach der Auswahl können die folgenden Grund-
menüfunktionen angepasst werden.
FM STEP (UKW-Kanalraster)
1 Drücken Sie M.C., um die UKW-Kanalraster-
Funktion zu wählen.
100 (100 kHz)50 (50 kHz)
SP-P/O MODE (Heckausgang- und Preout-Einstel-
lungen)
Der Hecklautsprecher-Leitungsausgang und
Cinch-Ausgang dieses Geräts können zum An-
schluss eines Vollbereichslautsprechers oder Sub-
woofers verwendet werden. Wählen Sie für Ihren
Anschluss eine geeignete Option.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
! REAR/SUB.W Wählen Sie diese Option,
wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang und
ein Subwoofer an den Cinch-Ausgang an-
geschlossen ist.
! SUB.W/SUB.W Wählen Sie diese Option,
wenn ein Subwoofer an den Hecklautspre-
cher-Leitungsausgang ohne Verwendung
eines zusätzlichen Verstärkers und ein Sub-
woofer an den Cinch-Ausgang angeschlos-
sen ist.
! REAR/REAR Wählen Sie diese Option,
wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang und
den Cinch-Ausgang angeschlossen ist.
Wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang ange-
schlossen ist und der Cinch-Ausgang nicht
verwendet wird, können Sie entweder
REAR/SUB.W oder REAR/REAR auswäh-
len.
Systemmenü
1 Drücken und halten Sie SRC/OFF ge-
drückt, bis sich das Gerät ausschaltet.
2 Drücken und halten Sie SRC/OFF ge-
drückt, bis das Hauptmenü im Display er-
scheint.
Gebrauch dieses Geräts
78
Abschnitt
Gebrauch dieses Geräts
De
02
Black plate (79,1)
3 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
4 Drehen Sie M.C., um die Systemmenü-
Funktion zu wählen.
Für detaillierte Informationen hierzu siehe Sys-
temmenü auf Seite 78.
Verwendung der AUX-
Programmquelle
1 Verbinden Sie den Stereo-Mini-Klinken-
stecker mit dem AUX-Eingang.
2 Drücken Sie die Taste SRC/OFF, um AUX
als Programmquelle zu wählen.
Hinweis
AUX kann nur gewählt werden, wenn die AUX-
Einstellung eingeschaltet wurde. Für weitere
Einzelheiten siehe AUX (Zusatzeingang) auf
Seite 78.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! Programmquellenname
! Programmquellname und Uhr
Bei Anzeige einer
unerwünschten Anzeige
Schalten Sie die unerwünschte Anzeige anhand
des unten beschriebenen Vorgangs aus.
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die Option
DEMO OFF zur Anzeige zu bringen, und drü-
cken Sie dann darauf, um Ihre Auswahl zu
bestätigen.
4 Drehen Sie M.C., um zu YES umzuschal-
ten.
5 Drücken Sie zur Auswahl M.C.
Anschlüsse
Wichtig
! Bei der Installation des Geräts in einem
Kraftfahrzeug, das am Zündschalter keine
Position ACC aufweist, kann es je nach An-
schlusstyp zu einer Entleerung der Fahrzeug-
batterie kommen, wenn das rote Kabel nicht
mit dem Anschluss verbunden wurde, der
für die Erkennung des Zündschlüsselbet-
riebs verantwortlich ist.
O
N
S
T
A
R
T
O
F
F
Zündung mit Position
ACC
Zündung ohne Posi-
tion ACC
! Der Einsatz dieses Geräts in einer anderen
als der nachstehend angegebenen Betriebs-
umgebung kann einen Brand auslösen oder
eine Funktionsstörung zur Folge haben:
Kraftfahrzeuge mit 12-Volt-Batterie und nega-
tiver Erdung.
Lautsprecher mit 50 W (Ausgabe) und 4 W bis
8 W (Impedanz).
! Um Kurzschluss, Überhitzung oder Funk-
tionsstörungen zu vermeiden, halten Sie sich
stets an die nachstehend aufgeführten An-
weisungen:
Trennen Sie die Verbindung zur negativen An-
schlussklemme der Fahrzeugbatterie, bevor
Sie das Gerät installieren.
Sichern Sie die Kabel mit Kabelklemmen
oder Klebeband. Zum Schutz der Verkabe-
lung sollten die Kabel an allen Stellen, an
denen sie mit Metallteilen in Berührung kom-
men, mit Isolierband umwickelt werden.
Bringen Sie die Kabel in sicherer Entfernung
von beweglichen Fahrzeugkomponenten, wie
z. B. Schalthebel und Sitzschienen, an.
Bringen Sie die Kabel in größtmöglicher Ent-
fernung von Stellen an, die sich erhitzen, wie
z. B. die Heizungsöffnung.
Führen Sie das gelbe Batteriekabel nicht
durch ein Loch in den Motorraum, um die
Verbindung mit der Fahrzeugbatterie herzu-
stellen.
Kleben Sie freie Kabelanschlüsse mit Isolier-
band ab.
Kürzen Sie die Kabel nicht.
Entfernen Sie niemals die Isolierung des
Stromkabels dieses Geräts, um die Stromzu-
fuhr mit einem anderen Gerät zu teilen. Da-
durch wird die Stromversorgungsleistung des
Kabels beeinträchtigt.
Verwenden Sie eine Sicherung, die den vorge-
gebenen Leistungsmerkmalen entspricht.
Verdrahten Sie das negative Lautsprecherka-
bel niemals direkt mit der Erde.
Gruppieren Sie niemals die negativen Kabel
mehrerer Lautsprecher.
! Wenn dieses Gerät eingeschaltet wird, liegen
Steuersignale am blau/weißen Kabel an. Ver-
binden Sie dieses Kabel mit der Systemfern-
bedienung eines externen
Leistungsverstärkers oder der Steuerklemme
des Automatikantennenrelais des Kraftfahr-
zeugs (max. 300 mA, 12 V Gleichspannung).
Wenn das Fahrzeug mit einer in die Heck-
scheibe integrierten Radioantenne ausge-
stattet ist, verbinden Sie das Kabel mit der
Versorgungsklemme des Antennenboosters.
! Verbinden Sie das blau/weiße Kabel niemals
mit der Leistungsklemme des externen Leis-
tungsverstärkers. Darüber hinaus darf das
Kabel keinesfalls mit der Leistungsklemme
der Fahrzeugantenne verbunden werden. An-
dernfalls kann es zu einer Entleerung oder
Funktionsstörung der Fahrzeugbatterie kom-
men.
Deutsch
Gebrauch dieses Geräts
79
Abschnitt
Installation
De
02
03
Black plate (80,1)
! Das schwarze Kabel gewährleistet die Er-
dung. Dieses Kabel wie auch die Erdungska-
bel anderer Produkte (insbesondere von
Hochstromprodukten wie Leistungsverstär-
ker) müssen separat verdrahtet werden. An-
derenfalls kann es zu einem Brand oder
einer Funktionsstörung kommen, wenn sich
die Kabel versehentlich lösen.
Dieses Gerät
3
1 24
5
1 Antenneneingang
2 Sicherung (10 A)
3 Netzkabelzugang
4 Eingang der festverdrahteten Fernbedienung
Es besteht die Möglichkeit, einen (separat er-
hältlichen) festverdrahteten Fernbedienungs-
adapter anzuschließen.
5 Heck- oder Subwooferausgang
Netzkabel
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Zum Netzzugang
2 Je nach Fahrzeugtyp können die Funktionen
3 und 5 variieren. Stellen Sie in diesem Fall
sicher, dass der Anschluss von 4 nach 5
und 6 nach 3 erfolgt.
3 Gelb
Reserveversorgung (oder Zubehör)
4 Gelb
Verbindung mit der Klemme der konstanten
12-V-Spannungsversorgung.
5 Rot
Zubehör (oder Reserveversorgung)
6 Rot
Verbindung mit der Klemme der zündungs-
gesteuerten Spannungsversorgung (12 V
Gleichspannung).
7 Verbinden Sie jeweils Anschlüsse derselben
Farbe miteinander.
8 Schwarz (Fahrgestell-Erdung)
9 Blau/Weiß
Die Pin-Position des ISO-Anschlusses variiert
je nach Fahrzeugtyp. Wird Pin 5 zur Steue-
rung der Antenne verwendet, verbinden Sie
9 und b. Verbinden Sie in jedem anderen
Fahrzeugtyp niemals 9 und b.
a Blau/Weiß
Verbindung mit der Systemsteuerungsklem-
me des Leistungsverstärkers (max. 300 mA,
12 V Gleichspannung).
b Blau/Weiß
Verbindung mit der Steuerungsklemme des
Automatikantennenrelais (max. 300 mA 12 V
Gleichspannung).
c Gelb/Schwarz
Wenn Sie ein Gerät mit Stummschaltfunk-
tion verwenden, verbinden Sie diesen Draht
mit dem Draht der Audio-Stummschaltung
dieses Geräts. Andernfalls sollte der Draht
der Audio-Stummschaltung (Mute) frei blei-
ben.
d Lautsprecherkabel
Weiß: Vorn links +
Weiß/Schwarz: Vorn links *
Grau: Vorn rechts +
Grau/Schwarz: Vorn rechts *
Grün: Hinten links + oder Subwoofer +
Grün/Schwarz: Hinten links * oder Subwo-
ofer *
Violett: Hinten rechts + oder Subwoofer +
Violett/Schwarz: Hinten rechts * oder Sub-
woofer *
e ISO-Anschluss
Bei manchen Fahrzeugtypen kann der ISO-
Anschluss zweigeteilt sein. Stellen Sie in die-
sem Fall sicher, dass zu beiden Anschlüssen
Verbindungen hergestellt werden.
Hinweise
! Ändern Sie das Grundeinstellmenü dieses
Geräts. Siehe SP-P/O MODE (Heckausgang-
und Preout-Einstellungen) auf Seite 78.
Die Subwoofer-Ausgabe dieses Geräts erfolgt
in Mono.
! Bei Verwendung eines 70-W-Subwoofers
(2 W) muss sichergestellt werden, dass der
Subwoofer am violetten und violett/schwar-
zen-Anschluss dieses Geräts angeschlossen
wird. Schließen Sie nichts an den grünen
und grün/schwarzen-Anschluss an.
Leistungsverstärker (separat
erhältlich)
Führen Sie diese Verkabelungen beim Gebrauch
eines optionalen Verstärkers durch.
1
3
2
4
55
1 Systemfernbedienung
Verbindung mit blau/weißem Kabel.
2 Leistungsverstärker (separat erhältlich)
3 Verbindung mit Cinch-Kabeln (separat er-
hältlich)
4 Zum Heck- oder Subwooferausgang
5 Hecklautsprecher oder Subwoofer
Installation
Wichtig
! Überprüfen Sie vor der endgültigen Installa-
tion alle Anschlüsse und Systeme.
! Die Verwendung nicht zugelassener Teile
kann eine Funktionsstörung zur Folge haben.
! Wenden Sie sich an Ihren Fachhändler, wenn
für die Installation Löcher gebohrt oder ande-
re Änderungen am Fahrzeug vorgenommen
werden müssen.
! Installieren Sie dieses Gerät keinesfalls an
folgenden Orten:
Orte, an denen das Gerät die Steuerung des
Fahrzeugs behindern könnte.
Orte, an denen das Gerät die Insassen des
Fahrzeugs im Anschluss an eine Schnell-
bremsung verletzen könnte.
Installation
80
Abschnitt
Installation
De
03
Black plate (81,1)
! Der Halbleiterlaser kann durch Überhitzung
beschädigt werden. Installieren Sie dieses
Gerät deshalb in sicherer Entfernung von Hit-
zequellen, wie z. B. Heizöffnungen.
! Optimale Leistung kann durch eine Installa-
tion des Geräts in einem Winkel unter 60° er-
zielt werden.
60°
! Um beim Gebrauch des Geräts eine ord-
nungsgemäße Wärmezerstreuung zu ge-
währleisten, ist bei der Installation genügend
Freiraum hinter der Rückseite vorzusehen.
Lose Kabel sind aufzuwickeln, damit sie die
Lüftung nicht behindern.
5cmcm
Reichlich Platz lassen
5 cm
5 cm
! Verwenden Sie für die Montage im Handel
erhältliches Zubehör.
Installationsmethode
Diese Einheit kann anhand einer der Methoden
in der unten stehenden Liste ordnungsgemäß
installiert werden:
! Installation mit Halterung
! Bei Anbringen mithilfe der Schraubenlöcher
auf beiden Seiten der Einheit
Vor dem Anbringen dieser Einheit
1 Entfernen Sie den Einpassungsring.
1
1 Einpassungsring
2 Führen Sie die mitgelieferten Extrak-
tionsschlüssel an beiden Geräteseiten ein,
bis sie in der richtigen Position einrasten.
3 Ziehen Sie das Gerät aus der Halterung.
Nehmen Sie die Halterung ab.
1
1 Halterung
(werkseitig mitgelieferte Teile)
Installation mit Halterung
1 Bringen Sie die Halterung am Armaturen-
brett an.
Wählen und biegen Sie nach dem Einsetzen der
Halterung im Armaturenbrett die Klammern ent-
sprechend der Dicke des Armaturenbrettmate-
rials. (Setzen Sie diese Einheit so fest wie
möglich mithilfe der oberen und unteren Klam-
mern ein. Biegen Sie die Klammern 90 Grad, um
einen fest Halt zu gewährleisten.)
1
2
1 Armaturenbrett
2 Halterung
(werkseitig mitgelieferte Teile)
2 Installieren Sie dieses Gerät.
1
1 Armaturenbrett
3 Setzen Sie den Einpassungsring ein.
1
1 Einpassungsring
Entfernen der Halterung
Dieser Vorgang ist der gleiche wie unter Vor
dem Anbringen dieser Einheit. Für detaillierte
Informationen hierzu siehe Vor dem Anbringen
dieser Einheit auf Seite 81.
Bei Anbringen mithilfe der
Schraubenlöcher auf beiden
Seiten der Einheit
% Befestigen Sie die Einheit an der werksei-
tig-angebrachten Radiomontageklammer.
Richten Sie das Gerät so aus, dass seine
Schraubenlöcher mit den Schraubenlöchern
der Klammer übereinstimmen, und ziehen Sie
die drei Schrauben auf jeder Seite fest.
Deutsch
Installation
81
Abschnitt
Installation
De
03
Black plate (82,1)
1
2
4
3
1 Sollte die Sperrklinke im Weg sein, biegen
Sie sie nach unten.
2 Werkseitig bereitgestellte Radio-Montage-
klammer
3 Trägerschrauben (5 mm × 8 mm)
4 Armaturenbrett oder Konsole
Fehlerbehebung
Symptome sind in Fett, Ursachen in normalem,
nicht eingerückten Text und Abhilfemaßnahmen
in normalem, eingerückten Text geschrieben.
Das Display schaltet automatisch in die normale
Anzeige um.
Sie haben keinen Bedienvorgang innerhalb von 30
Sekunden durchgeführt.
Wiederholen Sie den Vorgang.
Der Wiederholbereich ändert sich unerwartet.
Ja nach Wiederholbereich kann sich der ausgewähl-
te Bereich ändern, sobald ein anderer Ordner oder
Musiktitel ausgewählt wird oder während des
schnellen Vor- und Rücklaufs.
Wählen Sie den Wiederholbereich erneut aus.
Ein Unterordner wird nicht wiedergegeben.
Unterordner können nicht wiedergegeben werden,
wenn FLD (Ordner-Wiederholung) ausgewählt ist.
Wählen Sie einen anderen Wiederholbereich.
NO XXXX erscheint, wenn sich die Anzeige än-
dert (z. B. NO TITLE).
Es sind keine Textinformationen eingebettet.
Schalten Sie die Anzeige um oder spielen Sie
einen anderen Titel bzw. eine andere Datei ab.
Im Gerät ist eine Fehlfunktion aufgetreten.
Es liegen Funkstörungen vor.
Sie verwenden ein Gerät, wie z. B. ein Mobiltelefon,
welches Störgeräusche verursachen könnte.
Lassen Sie einen ausreichenden Abstand
zwischen dieser Einheit und den Geräten, die die
Funkstörung verursachen.
Fehlermeldungen
Vor der Kontaktaufnahme mit Ihrem Händler
oder der nächstgelegenen Pioneer-Kunden-
dienststelle sollten Sie sich die angezeigte Feh-
lermeldung notieren.
Fehlermeldungen sind in Fett, Ursachen in nor-
malem, nicht eingerückten Text und Abhilfe-
maßnahmen in normalem, eingerückten Text
geschrieben.
Allgemeines
AMP ERROR
Betriebsstörung des Geräts oder falsche Lautspre-
cherverbindung; Schutzschaltung ist aktiviert.
Überprüfen Sie die Lautsprecherverbindung.
Wenn die Meldung selbst nach dem Aus-/
Einschalten des Motors weiterhin angezeigt wird,
wenden Sie sich zur Unterstützung an Ihren
Händler oder eine Pioneer-Kundendienststelle.
CD-Player
ERROR-07, 11, 12, 17, 30
Die Disc ist verschmutzt.
Reinigen Sie die Disc.
Die Disc ist verkratzt.
Wechseln Sie die Disc aus.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Es liegt ein elektrischer oder mechanischer Fehler
vor.
Schalten Sie die Zündung aus (OFF) und wieder
ein (ON) oder schalten Sie auf eine andere
Programmquelle um und dann wieder zum CD-
Player zurück.
ERROR-15
Die eingelegte Disc ist leer.
Wechseln Sie die Disc aus.
Installation
82
Abschnitt
Zusätzliche Informationen
De
03
Black plate (83,1)
ERROR-23
Nicht unterstütztes CD-Format.
Wechseln Sie die Disc aus.
FORMAT READ
Nach dem Wiedergabestart ist der Ton in manchen
Fällen erst nach einer Verzögerung zu hören.
Warten Sie bis die Anzeige erlischt und Sie einen
Ton hören.
NO AUDIO
Die eingelegte Disc enthält keine abspielbaren Da-
teien.
Wechseln Sie die Disc aus.
SKIPPED
Die eingelegte Disc enthält Dateien mit DRM-Schutz
(digitale Rechteverwaltung).
Die geschützten Dateien werden übersprungen.
PROTECT
Alle Dateien auf der eingelegten Disc weisen einen
DRM-Schutz (digitale Rechteverwaltung) auf.
Wechseln Sie die Disc aus.
USB-Speichermedium/iPod
FORMAT READ
Nach dem Wiedergabestart ist der Ton in manchen
Fällen erst nach einer Verzögerung zu hören.
Warten Sie bis die Anzeige erlischt und Sie einen
Ton hören.
NO AUDIO
Es sind keine Musiktitel vorhanden.
Übertragen Sie die Audio-Dateien auf das USB-
Speichermedium und schließen Sie das Gerät
dann an.
Es wurde ein USB-Speichermedium mit aktivierter
Sicherheitsfunktion angeschlossen.
Halten Sie sich an die Anweisungen in der
Bedienungsanleitung des USB-
Speichermediums, um die Sicherheitsfunktion
zu deaktivieren.
SKIPPED
Das verbundene USB-Speichermedium enthält Da-
teien mit DRM-Schutz.
Die geschützten Dateien werden übersprungen.
PROTECT
Alle Dateien auf dem verbundenen USB-Speicher-
medium sind mit DRM geschützt.
Tauschen Sie das USB-Speichermedium aus.
N/A USB
Das angeschlossene USB-Gerät wird von diesem
Gerät nicht unterstützt.
! Schließen Sie ein dem Standard USB-
Massenspeicher-Klasse entsprechendes Gerät
an.
! Trennen Sie das Gerät ab und schließen Sie ein
kompatibles USB-Speichermedium an.
CHECK USB
Der USB-Anschluss oder das USB-Kabel wurde kurz-
geschlossen.
Stellen Sie sicher, dass die USB-Klemme oder
das USB-Kabel nicht eingeklemmt oder
beschädigt ist.
CHECK USB
Das angeschlossene USB-Speichermedium ver-
braucht mehr als den maximal zulässigen Stromver-
brauch.
Trennen Sie das USB-Speichermedium von
diesem Gerät und verwenden Sie es nicht mehr
in Verbindung mit dem Gerät. Drehen Sie den
Zündschlüssel in die Position OFF (Aus) und
anschließend in die Position ACC oder ON (Ein).
Schließen Sie dann nur ein kompatibles USB-
Speichermedium an.
CHECK USB
Der iPod funktioniert ordnungsgemäß, wird jedoch
nicht geladen.
Kontrollieren Sie, dass das iPod-Kabel nicht
kurzgeschlossen (d. h. zwischen Gegenständen
aus Metall eingeklemmt) wurde. Schalten Sie
anschließend die Zündung aus (OFF) und wieder
ein (ON) oder trennen Sie die Verbindung zum
iPod und schließen Sie den iPod dann wieder an.
ERROR-19
Kommunikation gestört.
Führen Sie einen der folgenden Bedienvorgänge
durch:
Schalten Sie die Zündung aus (OFF) und
wieder ein (ON).
Trennen Sie das USB-Speichermedium vom
Gerät.
Schalten Sie auf eine andere Programmquelle
um.
Kehren Sie anschließend wieder zur
Programmquelle USB zurück.
iPod gestört.
Trennen Sie das Kabel vom iPod. Sobald das
Hauptmenü auf dem iPod erscheint, schließen
Sie ihn erneut an und setzen Sie ihn zurück.
ERROR-23
Das USB-Speichermedium wurde nicht mit FAT12,
FAT16 oder FAT32 formatiert.
Das USB-Speichermedium sollte mit FAT12,
FAT16 oder FAT32 formatiert sein.
ERROR-16
Die iPod-Firmwareversion ist veraltet.
Aktualisieren Sie die iPod-Version.
iPod gestört.
Trennen Sie das Kabel vom iPod. Sobald das
Hauptmenü auf dem iPod erscheint, schließen
Sie ihn erneut an und setzen Sie ihn zurück.
STOP
Die aktuelle Liste enthält keine Musiktitel.
Wählen Sie eine Liste, die Musiktitel enthält.
NOT FOUND
Keine entsprechenden Musiktitel gefunden.
Übertragen Sie Musiktitel auf den iPod.
Anwendung
START UP APP
Die Anwendung ist noch nicht betriebsbereit.
Folgen Sie den auf dem Bildschirm angezeigten
Anweisungen.
Deutsch
Zusätzliche Informationen
83
Anhang
Zusätzliche Informationen
De
Black plate (84,1)
Handhabungsrichtlinien
Discs und Player
Verwenden Sie ausschließlich Discs, die eines der
folgenden zwei Logos aufweisen:
Verwenden Sie 12-cm-Discs.
Verwenden Sie ausschließlich herkömmliche,
runde Discs.
Die folgenden Disc-Typen können nicht mit die-
sem Gerät verwendet werden:
! DualDiscs
! 8-cm-Discs: Versuche solche Discs mit einem
Adapter zu verwenden, können zu Fehlfunktio-
nen des Geräts führen.
! Discs in ungewöhnlichen Formen
! Andere Discs als CDs
! Beschädigte Discs einschließlich Discs mit
Rissen, Verwellungen und abgeplatzten Teilen
! CD-R/RW-Discs mit nicht abgeschlossener
Aufzeichnung
Berühren Sie unter keinen Umständen die Disc-
Oberfläche mit den aufgezeichneten Daten.
Bewahren Sie die Discs bei Nichtgebrauch in
deren Hülle auf.
Kleben Sie keine Etiketten auf Discs, beschriften
Sie sie nicht und wenden Sie keine Chemikalien
auf die Disc-Oberfläche an.
Wischen Sie die Discs zum Reinigen mit einem
weichen Tuch von der Mitte zum Rand hin ab.
Kondensation kann eine vorübergehende Störung
der Player-Leistung zur Folge haben. Warten Sie in
diesem Fall etwa eine Stunde ab, bis sich der
Player an die höheren Temperaturen angepasst
hat. Zudem sollten feuchte Discs mit einem wei-
chen Tuch trockengerieben werden.
Unter Umständen ist eine Disc-Wiedergabe nicht
möglich. Das kann auf die spezifischen Eigen-
schaften der Disc, das Disc-Format, die für die
Aufzeichnung verwendete Software, die Wiederga-
beumgebung, die Lagerbedingungen usw. zurück-
zuführen sein.
Erschütterungen aufgrund von Unebenheiten der
Fahrbahn können die Disc-Wiedergabe unterbre-
chen.
Bei Verwendung von bedruckbaren Discs, beach-
ten Sie die Anleitung und die Warnhinweise der
Disc. Je nach Beschaffenheit der Discs, können
Sie eventuell nicht eingelegt oder ausgeworfen
werden. Die Verwendung solcher Discs kann zu
einer Beschädigung dieses Gerätes führen.
Bringen Sie keine handelsüblichen Etiketten oder
andere Materialien auf den Discs an.
! Die Discs können sich verformen und werden
nicht wiedergegeben.
! Die Etiketten können sich während der Wieder-
gabe lösen und den Auswurf behindern, wo-
durch das Gerät beschädigt werden könnte.
USB-Speichermedium
Verbindungen über einen USB-Hub werden nicht
unterstützt.
Schließen Sie ausschließlich USB-Speicherme-
dien an.
Sorgen Sie für eine sichere Befestigung des USB-
Speichermediums während der Fahrt. Lassen Sie
das USB-Speichermedium nicht auf den Boden
fallen, wo es unter der Bremse oder dem Gaspedal
eingeklemmt werden könnte.
Je nach USB-Speichermedium können folgende
Probleme auftreten:
! Die Bedienung kann unterschiedlich sein.
! Das Speichergerät wird unter Umständen
nicht erkannt.
! Dateien werden eventuell nicht richtig wieder-
gegeben.
! Das Gerät kann Störgeräusche verursachen,
während Sie Radio hören.
iPod
Bewahren Sie den iPod nicht an Orten auf, an
denen hohe Temperaturen herrschen.
Sorgen Sie für eine sichere Befestigung des iPods
während der Fahrt. Lassen Sie den iPod nicht auf
den Boden fallen, wo er unter der Bremse oder
dem Gaspedal eingeklemmt werden könnte.
Zu den iPod-Einstellungen
! Wenn ein iPod an dieses Gerät angeschlossen
wird, wird die Equalizer-Einstellung des iPods
automatisch deaktiviert, um die Akustik zu op-
timieren. Beim Trennen der Verbindung wird
der Equalizer auf die ursprüngliche Einstellung
zurückgesetzt.
! Bei der Verwendung dieses Geräts lässt sich
die Wiederholfunktion auf dem iPod nicht aus-
schalten. Wenn ein iPod mit diesem Gerät ver-
bunden ist, wird die Funktion zur
Wiederholung aller Titel automatisch aktiviert.
Auf dem iPod gespeicherter Text, der nicht mit die-
sem Gerät kompatibel ist, wird nicht angezeigt.
Kompatible komprimierte
Audio-Formate (Discs, USB-
Speichermedien)
WMA
Dateierweiterung: .wma
Bitrate: 48 Kbit/s bis 320 Kbit/s (CBR - Konstante
Bitrate), 48 Kbit/s bis 384 Kbit/s (VBR - Variable Bit-
rate)
Abtastfrequenz: 32 kHz; 44,1 kHz; 48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream mit Video: Nicht kom-
patibel
MP3
Dateierweiterung: .mp3
Bitrate: 8 Kbit/s bis 320 Kbit/s (CBR), VBR
Abtastfrequenz: 8 kHz bis 48 kHz (32 kHz; 44,1 kHz;
48 kHz für Emphase)
Kompatible ID3-Tag-Version: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3-Tag-Version 2.x erhält Vorrang vor Version 1.x)
M3u-Spielliste: Nicht kompatibel
MP3i (MP3 interaktiv), mp3 PRO: Nicht kompati-
bel
WAV
Dateierweiterung: .wav
Quantisierungsbits: 8 und 16 (LPCM), 4 (MS
ADPCM)
Abtastfrequenz: 16 kHz bis 48 kHz (LPCM);
22,05 kHz und 44,1 kHz (MS ADPCM)
Zusätzliche Informationen
84
Anhang
Zusätzliche Informationen
De
Black plate (85,1)
! Diese Funktion kann nicht mit USB MTP ver-
wendet werden.
Zusätzliche Informationen
Von Dateinamen (einschließlich der Dateierweite-
rung) bzw. von Ordnernamen können jeweils nur
die ersten 32 Zeichen angezeigt werden.
Damit kyrillische Buchstaben auf diesem Gerät
angezeigt werden können, müssen diese mit
einem der folgenden Zeichensätze codiert worden
sein:
! Unicode (UTF-8, UTF-16)
! Andere Zeichensätze als Unicode, die in einer
Windows-Umgebung verwendet und in den
Sprachoptionen auf Russisch eingestellt wur-
den.
Je nach der Anwendung, die für die Codierung
der WMA-Dateien verwendet wurde, funktioniert
dieses Gerät ggf. nicht ordnungsgemäß.
Nach dem Wiedergabestart kann es bei Audio-Da-
teien, in die Bilddaten eingebettet wurden bzw. bei
Audio-Dateien auf einem USB-Speichermedium
mit einer komplexen Ordnerhierachie zu einer kur-
zen Verzögerung kommen.
Disc
Abspielbare Ordnerstruktur: bis zu acht Ebenen
(der Einfachheit halber sollte die Ordnerstruktur
jedoch aus weniger als zwei Ebenen bestehen).
Abspielbare Ordner: bis zu 99
Abspielbare Dateien: bis zu 999
Dateisystem: Konformität mit ISO 9660 Stufe 1
und 2, Romeo, Joliet
Multi-Session-Wiedergabe: Kompatibel
Datenübertragungen im Paketverfahren: Nicht
kompatibel
Ungeachtet der Länge der Leerstellen, die die Ori-
ginalaufnahme zwischen den einzelnen Musikti-
teln aufweist, wird bei der Wiedergabe von
komprimierten Audio-Discs stets eine kurze Pause
zwischen den Titeln eingefügt.
USB-Speichermedium
Abspielbare Ordnerstruktur: bis zu acht Ebenen
(der Einfachheit halber sollte die Ordnerstruktur
jedoch aus weniger als zwei Ebenen bestehen).
Abspielbare Ordner: bis zu 500
Abspielbare Dateien: bis zu 15 000
Wiedergabe von urheberrechtlich geschützten Da-
teien: Nicht kompatibel
Partitioniertes USB-Speichermedium: Es kann nur
die erste Partition wiedergegeben werden.
Beim Start der Wiedergabe von Audio-Dateien auf
einem USB-Speichermedium, das eine komplexe
Ordnerhierarchie aufweist, ist der Ton u. U. erst
mit einiger Verzögerung zu hören.
VORSICHT
! Pioneer kann nicht die Kompatibilität mit
allen USB-Speichermedien gewährleisten
und übernimmt keine Verantwortung für
eventuelle Datenverluste auf Media-Playern,
Smartphones oder anderen Geräten, die mit
diesem Gerät verwendet werden.
! Bewahren Sie keine Discs oder USB-Spei-
chermedien an Orten auf, an dem erhöhte
Temperaturen herrschen.
iPod-Kompatibilität
Dieses Gerät unterstützt nur die folgenden iPod-
Modelle.
Hergestellt für
! iPod touch (5. Generation)
! iPod touch (4. Generation)
! iPod touch (3. Generation)
! iPod touch (2. Generation)
! iPod touch (1. Generation)
! iPod classic
! iPod mit Video
! iPod nano (7. Generation)
! iPod nano (6. Generation)
! iPod nano (5. Generation)
! iPod nano (4. Generation)
! iPod nano (3. Generation)
! iPod nano (2. Generation)
! iPod nano (1. Generation)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Je nach iPod-Generation bzw. -Version können ei-
nige Funktionen nicht verfügbar sein.
Je nach der iPod-Softwareversion gestaltet sich
die Bedienung ggf. etwas unterschiedlich.
Benutzer eines iPod mit Lightning-Anschluss soll-
ten das (im iPod-Lieferumfang enthaltene) Light-
ning-auf-USB-Kabel verwenden.
Benutzer eines iPod mit Dock-Anschluss sollten
ein CD-IU51 verwenden. Weitere Einzelheiten er-
fahren Sie bei Ihrem Fachhändler.
Informationen bezüglich der Datei-/Formatkompa-
tibilität finden Sie im Handbuch Ihres iPods.
Hörbücher, Podcasts: Kompatibel
VORSICHT
Pioneer haftet in keinem Fall für den Verlust von
Daten auf einem iPod, selbst dann nicht, wenn
der Datenverlust während der Verwendung die-
ses Geräts aufgetreten ist.
Reihenfolge der Audio-Dateien
Der Benutzer kann keine Ordnernummern zu-
weisen und auch die Wiedergabereihenfolge mit
diesem Gerät nicht bestimmen.
Beispiel einer Datenträger-Struktur
1
2
3
4
5
6
01
02
03
04
05
Stufe 1 Stufe 2 Stufe 3 Stufe 4
: Ordner
: Komprimierte
Audio-Datei
01 bis 05: Ordner-
nummer
1 bis 6: Wiederga-
bereihenfolge
Disc
Die bei der Ordnerauswahl oder einem anderen
Bedienvorgang angewendete Reihenfolge kann
sich je nach der verwendeten Codierungs- bzw.
Schreibsoftware ändern.
USB-Speichermedium
Die Wiedergabereihenfolge entspricht der Auf-
zeichnungsreihenfolge auf dem USB-Speicher-
medium.
Für die Bestimmung der Wiedergabereihenfolge
wird folgende Vorgehensweise empfohlen:
1 Erstellen Sie Dateinamen basierend auf Zah-
len, um dadurch die gewünschte Wiederga-
bereihenfolge festzulegen (z. B. 001xxx.mp3
oder 099yyy.mp3).
2 Speichern Sie diese Dateien in einem Ord-
ner.
Deutsch
Zusätzliche Informationen
85
Anhang
Zusätzliche Informationen
De
Black plate (86,1)
3 Speichern Sie den Ordner mit den Dateien
auf dem USB-Speichermedium.
Je nach Systemumgebung ist eine Festlegung
der Dateiwiedergabereihenfolge jedoch u. U.
nicht möglich.
Die Dateireihenfolge bei tragbaren USB-Audio-
Playern unterscheidet sich jeweils vom verwen-
deten Player.
Russischer Zeichensatz
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Anzeige C: Zeichen
Copyrights und Marken
MP3
Die Bereitstellung dieses Produkts erfolgt in Ver-
bindung mit einer Lizenz zur privaten, nicht-
kommerziellen Nutzung und impliziert weder die
Übertragung einer Lizenz noch die Einräumung
eines Rechts zur Verwendung dieses Produkts
in kommerziellen (d. h. ertragsorientierten) Live-
Programmen (leitungsbasiert, per Satellit, Kabel
und/oder über jedes beliebige andere Medium),
zum Broadcasting/Streaming über das Internet,
über Intranets und/oder andere Netzwerke oder
in anderen elektronischen Inhalt-Vertriebssyste-
men, z. B. Pay-Audio- oder Audio-on-de-
mand-Anwendungen. Für eine derartige
Nutzung ist eine separate Lizenz erforderlich.
Detaillierte Informationen hierzu finden Sie
unter
http://www.mp3licensing.com.
WMA
Windows Media ist eine eingetragene Marke
oder eine Marke der Microsoft Corporation in
den USA und/oder anderen Ländern.
Dieses Produkt enthält Technologie, die Eigen-
tum der Microsoft Corporation ist und nicht
ohne Lizenz von Microsoft Licensing, Inc. vertrie-
ben werden darf.
iPod und iPhone
iPhone, iPod, iPod classic, iPod nano und iPod
touch sind in den USA sowie in anderen Län-
dern eingetragene Marken von Apple Inc.
Lightning ist ein Warenzeichen der Apple Inc.
Die Kennzeichnungen Made for iPod und
Made for iPhone bedeuten, dass ein elektron-
isches Zubehörteil spezifisch zum Anschluss an
iPod oder iPhone konstruiert wurde und entspre-
chend vom Entwickler als die Leistungsstan-
dards von Apple erfüllend zertifiziert wurde.
Apple übernimmt keine Verantwortung für die
richtige Funktion dieses Geräts oder seine Erfül-
lung von Sicherheits- oder anderen Vorschriften.
Bitte beachten Sie, dass der Gebrauch dieses
Zubehörteils in Verbindung mit einem iPod oder
iPhone die drahtlose Leistung beeinträchtigen
kann.
Androidä
Android ist eine Marke von Google Inc.
Technische Daten
Allgemein
Stromversorgung ............. 14,4 V Gleichspannung (Tole-
ranz 10,8 V bis 15,1 V)
Erdungssystem ................ Negativ
Maximale Leistungsaufnahme
................................... 10,0 A
Abmessungen (B × H × T):
DIN
Einbaugröße .................... 178 mm × 100mm × 157mm
Frontfläche ...................... 188 mm × 118mm × 25mm
D
Einbaugröße .................... 178 mm × 100mm × 165mm
Frontfläche ...................... 170 mm × 96mm × 17mm
Gewicht ........................... 1,2 kg
Audio
Max. Ausgangsleistung .... 50 W × 4
70 W × 1/2 W (für Subwoofer)
Dauer-Ausgangsleistung
................................... 22W × 4 (50Hz bis 15000Hz,
5 % THD, bei 4-W-Last, beide
Kanäle betrieben)
Lastimpedanz .................. 4 W (4 W bis 8 W zulässig)
Maximaler Preout-Ausgangspegel
................................... 2,0V
Loudness-Kontur ............. +10 dB (100 Hz), +6,5 dB (10
kHz) (Lautstärke: 30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequenz .......................... 80Hz/250 Hz/800 Hz/2,5 kHz/
8 kHz
Entzerrungsbereich .......... ±12 dB (Inkrement 2 dB)
Subwoofer (Mono):
Frequenz .......................... 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Steilheit ........................... 12 dB/Okt., 24 dB/Okt.
Verstärkung ..................... +6dB bis 24 dB
Phase .............................. Normal/Gegen
CD-Player
Typ ................................... Compact-Disc-Digital-Audio-
system
Kompatible Discs ............. Compact Disc
Signal-Rauschabstand ..... 94dB (1kHz) (IEC-A-Netz)
Anzahl der Kanäle ............ 2 (Stereo)
MP3-Decodiermodus ....... MPEG-1 und 2 Audio Layer 3
WMA-Decodiermodus ...... Vers. 7, 7.1, 8, 9, 10, 11, 12 (2-
Kanal-Audio)
(Windows Media Player)
WAV-Signalformat ............ Lineare PCM und MS ADPCM
(nicht komprimiert)
USB
USB-Standard-Spezifikation
................................... USB 2.0 Full Speed
Maximale Stromversorgung
................................... 1 A
USB-Klasse ..................... MSC (Massenspeicher-Klas-
se)
Dateisystem ..................... FAT12, FAT16, FAT32
MP3-Decodiermodus ....... MPEG-1 und 2 Audio Layer 3
WMA-Decodiermodus ...... Vers. 7, 7.1, 8, 9, 10, 11, 12 (2-
Kanal-Audio)
(Windows Media Player)
WAV-Signalformat ............ Lineare PCM und MS ADPCM
(nicht komprimiert)
UKW-Tuner
Frequenzbereich .............. 87,5 MHz bis 108,0 MHz
Nutzempfindlichkeit ......... 9 dBf (0,8 µV/75 W, Mono, Sig -
nal-Rauschabstand: 30 dB)
Signal-Rauschabstand ..... 72dB (IEC-A-Netz)
MW-Tuner
Frequenzbereich .............. 531 kHz bis 1602kHz
Nutzempfindlichkeit ......... 25µV (Signal-Rauschabstan d:
20 dB)
Signal-Rauschabstand ..... 62dB (IEC-A-Netz)
LW-Tuner
Frequenzbereich .............. 153 kHz bis 281 kHz
Nutzempfindlichkeit ......... 28µV (Signal-Rauschabstan d:
20 dB)
Signal-Rauschabstand ..... 62dB (IEC-A-Netz)
Hinweis
Änderungen der technischen Daten und des De-
signs vorbehalten.
Zusätzliche Informationen
86
Anhang
Zusätzliche Informationen
De
Black plate (87,1)
Deutsch
87De
Black plate (88,1)
Hartelijk dank voor uw keuze voor dit
Pioneer-product
Lees deze handleiding voordat u het product in
gebruik neemt zodat u het goed leert gebruiken.
Lees vooral de gedeelten die met WAARSCHU-
WING en LET OP gemarkeerd zijn aandachtig.
Bewaar deze handleiding na het lezen op een vei-
lige, voor de hand liggende plaats zodat u hem in-
dien nodig altijd kunt raadplegen.
Deponeer dit product niet bij het gewone
huishoudelijk afval wanneer u het wilt verwij-
deren. Er bestaat een speciaal wettelijk voor-
geschreven verzamelsysteem voor de juiste
behandeling, het opnieuw bruikbaar maken
en de recycling van gebruikte elektronische
producten.
In de lidstaten van de EU en in Zwitserland en
Noorwegen kunnen particulieren afgedankte
elektronische producten gratis bij de daarvoor
bestemde verzamelplaatsen inleveren. Als u een
soortgelijk nieuw product koopt, kunt u het afge-
dankte product ook bij uw verkooppunt inleve-
ren.
Als u in een ander land woont, neem dan con-
tact op met de plaatselijke overheid voor infor-
matie over het weggooien van afgedankte
producten.
Op die manier zorgt u ervoor dat uw afgedankte
product op de juiste wijze wordt verwerkt, herge-
bruikt en gerecycled, zonder schadelijke gevol-
gen voor het milieu en de volksgezondheid.
Informatie over dit toestel
De tuner van dit toestel kan worden afgestemd
op frequenties die gebruikt worden in West-Eu-
ropa, Azië, het Midden-Oosten, Afrika en Ocea-
nië. In andere gebieden is de ontvangst wellicht
slecht. De RDS-functie (Radio Data System)
werkt alleen in gebieden waar FM-zenders RDS-
informatie uitzenden.
WAARSCHUWING
! Probeer het product niet zelf te monteren
en voer er geen onderhoud aan uit. Mon-
tage of onderhoud van het product door
personen zonder technische opleiding en
ervaring met elektronische apparatuur
en auto-accessoires kan gevaarlijk zijn,
en kan een elektrische schok, verwon-
ding of andere gevaren veroorzaken.
! Bedien het toestel niet tijdens het rijden. Als
u knoppen op het toestel wilt bedienen, moet
u het voertuig eerst van de weg halen en op
een veilige plaats parkeren.
LET OP
! Zorg ervoor dat het toestel niet met vloeistof
in aanraking komt. Een elektrische schok
kan daarvan het gevolg zijn. Bovendien kan
contact met vloeistoffen rookvorming, over-
verhitting en andere schade aan het toestel
veroorzaken.
! De Pioneer CarStereo-Pass wordt alleen in
Duitsland gebruikt.
! Zet het volume nooit zo hoog dat u geluiden
buiten het voertuig niet meer kunt horen.
! Zorg dat het toestel niet wordt blootgesteld
aan vocht.
LET OP
Dit apparaat is geclassificeerd als een klasse
1 laserproduct onder de veiligheidsnormen
voor laserproducten, IEC 60825-1:2007.
KLASSE 1 LASERPRODUCT
Bij problemen
Neem contact op met uw leverancier of het
dichtstbijzijnde erkende Pioneer-servicecentrum
als het toestel niet naar behoren functioneert.
Vóór u begint
88
Hoofdstuk
Vóór u begint
Nl
01
Black plate (89,1)
Hoofdtoestel
1 2 4 5
8 9
7 a c6 b d
3
1 h (uitwerpen)
2 iPod
3 1/
tot 6/
4 Laadsleuf voor disc
5 DISP
6 SRC/OFF
7 BAND/
(iPod-bediening)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(terug)/DIMMER (dimmer)
b
(lijst)
c AUX-ingang (3,5 mm-stereoplug)
d USB-poort
LET OP
Sluit een USB-opslagapparaat via een Pioneer
USB-kabel (CD-U50E, optioneel) op dit toestel
aan. Sluit het niet rechtstreeks op dit toestel aan
omdat het dan uitsteekt en verwondingen of be-
schadigingen kan veroorzaken.
Display-indicaties
31 4 86
a
2 5 7 9
b
1 (lijst)
2
(iPod-bediening)
De iPod-functie van dit toestel wordt via de
iPod bediend.
3 Bijkomende informatie
4 TA (verkeersberichten)
5 TP (verkeersprogramma-identificatie)
6
(sound retriever)
7
LOC (automatisch afstemmen op lokale zen-
ders)
8
(herhalen)
9
(willekeurig)
a
Basisinformatie
! Tuner: frequentieband en frequentie
! RDS: programmaservicenaam, PTY-infor-
matie en andere tekstinformatie
! Cd-speler, USB-opslagapparaat en iPod:
verstreken weergavetijd en tekstinforma-
tie
b
Licht op wanneer er een menu of mappen
op een lager niveau bestaan.
Instellingenmenu
1 Zet het contact aan na de installatie van
dit toestel.
SET UP verschijnt.
2 Draai aan M.C. en selecteer YES.
# Als u het toestel niet binnen 30 seconden ge-
bruikt, wordt het instellingenmenu niet weergege-
ven.
# Als u de instelling later wilt maken, selecteert u
met M.C. nu NO.
3 Druk op M.C. om uw keuze te bevesti-
gen.
4 Volg deze stappen om het menu in te
stellen.
Om verder te gaan naar de volgende menu-
optie, moet u uw selectie bevestigen.
LANGUAGE (taalinstelling)
Dit toestel kan Engelse, Russische of Turkse tekst-
informatie bij een gecomprimeerd audiobestand
weergeven.
! Als de gebruikte taal niet overeenkomt met de
taalinstelling van dit toestel, wordt tekst wel-
licht niet correct weergegeven.
! Het is mogelijk dat sommige tekens niet juist
worden weergegeven.
1 Draai aan M.C. en selecteer de gewenste in-
stelling.
ENG (Engels)РУС (Russisch)TUR (Turks)
2 Druk op M.C. om de selectie te bevestigen.
CLOCK SET (klok)
1 Draai aan M.C. om het uur in te stellen.
2 Druk op M.C. om de minuut te selecteren.
3 Draai aan M.C. om de minuut in te stellen.
4 Druk op M.C. om de selectie te bevestigen.
FM STEP (FM-afstemstap)
Gebruik FM STEP om de FM-afstemstap in te stel-
len (afstemstap bij het zoeken).
1 Draai aan M.C. en selecteer de FM-afstemstap.
100 (100 kHz)50 (50 kHz)
2 Druk op M.C. om de selectie te bevestigen.
QUIT verschijnt.
! Bij handmatig afstemmen is de afstemstap
vast ingesteld op 50 kHz.
! Als de functies AF en TA zijn uitgeschakeld, is
de afstemstap vast ingesteld op 50 kHz, ook als
100 is geselecteerd.
5 Draai aan M.C. en selecteer YES om de in-
stelling te voltooien.
# Als u nog iets wilt wijzigen, draait u M.C. naar
NO.
6 Druk op M.C. om uw keuze te bevesti-
gen.
Opmerkingen
! U kunt de menu-opties instellen in het sys-
teemmenu en het begininstellingenmenu.
Raadpleeg Systeemmenu op bladzijde 95 en
Beginmenu op bladzijde 95 voor meer infor-
matie over de instellingen.
! U kunt het instellingenmenu annuleren door
op SRC/OFF te drukken.
Basisbediening
Het toestel inschakelen
1 Druk op SRC/OFF om het toestel in te schake-
len.
Het toestel uitschakelen
1 Houd SRC/OFF ingedrukt tot het toestel uit
gaat.
Nederlands
Gebruik van het toestel
89
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (90,1)
Een signaalbron selecteren
1 Druk op SRC/OFF om over te schakelen tus-
sen:
RADIOCDUSB/iPodAPP (toepassing)
AUX
! Wanneer de MTP-verbinding actief is, wordt
USB MTP weergegeven.
! Als een iPod aangesloten is en een andere
bron dan iPod geselecteerd is, kunt u naar
iPod overschakelen door op iPod te drukken.
Het volume afstellen
1 Draai aan M.C. om het volume te regelen.
Opmerking
Als de blauw-witte draad van dit toestel is aange-
sloten op de bedieningsaansluiting van de auto-
matische antenne van het voertuig, schuift de
antenne uit wanneer er een signaalbron van dit
toestel wordt ingeschakeld. Als de signaalbron
wordt uitgeschakeld, wordt de antenne weer in-
geschoven.
Veelgebruikte menufuncties
Terugkeren naar het vorige display
Terugkeren naar de vorige lijst (de map die een ni-
veau hoger ligt)
1 Druk op
/DIMMER.
Terugkeren naar het gewone display
Het hoofdmenu annuleren
1 Druk op BAND/
.
Terugkeren naar het gewone display van de lijst
1 Druk op BAND/
.
Radio
Basisbediening
Een frequentieband selecteren
1 Druk op BAND/
totdat de gewenste frequen-
tieband (FM1, FM2, FM3 voor FM of MW/LW)
op het display verschijnt.
Overschakelen tussen voorkeuzestations
1 Druk op c of d.
! Om deze functie te gebruiken, moet u PCH
(voorkeuzezender) selecteren onder SEEK.
Handmatig afstemmen (stap voor stap)
1 Druk op c of d.
! Om deze functie te gebruiken, moet u MAN
(handmatig afstemmen) selecteren onder
SEEK.
Automatisch afstemmen
1 Houd c of d ingedrukt en laat deze weer los.
U kunt het automatisch afstemmen afbreken
door even op c of d te drukken.
Als u c of d ingedrukt houdt, worden zenders
overgeslagen. Het automatisch afstemmen be-
gint zodra u c of d loslaat.
Opmerkingen
! Raadpleeg SEEK (instelling linker/rechter
toets) op bladzijde 91 voor meer informatie
over SEEK.
! U kunt de AF-functie (zoeken naar alterna-
tieve frequenties) in- en uitschakelen. Voor
normaal afstemmen moet de AF-functie uit
staan (raadpleeg AF (alternatieve frequenties
zoeken) op bladzijde 91).
Zenders voor de verschillende
frequentiebanden opslaan en
oproepen
De voorkeuzetoetsen gebruiken
1 Opslaan: Houd de gewenste voorkeuzet-
oets (1/
t/m 6/ ) ingedrukt tot het num-
mer stopt met knipperen.
2 Oproepen: Druk op de gewenste voor-
keuzetoets (1/
t/m 6/ ).
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! FREQUENCY (programmaservicenaam of
frequentie)
! BRDCST INFO (programmaservicenaam/
PTY-informatie)
! CLOCK (naam signaalbron en klok)
Opmerkingen
! Als de programmaservicenaam niet gedetec-
teerd kan worden in FREQUENCY, wordt de
frequentie weergegeven. Anders wordt de
programmaservicenaam weergegeven.
! Afhankelijk van de frequentieband kan de
tekstinformatie verschillen.
! Welke tekstinformatie gewijzigd kan worden,
hangt af van het gebied.
PTY-functies
Met behulp van PTY-informatie (programmatype-
informatie) kunt u op een bepaald soort zender
afstemmen.
RDS-zenders zoeken via PTY-informatie
1 Druk op
(lijst).
2 Draai aan M.C. om een programmatype te kie-
zen.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Druk op M.C. om het zoeken te beginnen.
Het toestel zoekt naar een zender die het gese-
lecteerde programmatype uitzendt. Als er een
zender is gevonden, wordt de programmaservi-
cenaam weergegeven.
! Druk opnieuw op M.C. om het zoeken te
annuleren.
! Het programma van een zender kan afwij-
ken van de informatie die door de PTY-code
wordt aangegeven.
! Als er geen zender gevonden wordt die het
gewenste soort programma uitzendt, wordt
op het display ongeveer twee seconden
lang NOT FOUND getoond en keert de
tuner terug naar de oorspronkelijke zender.
PTY-lijst
Bezoek de volgende website voor meer informa-
tie over de PTY-lijst:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
3 Draai aan M.C. om de gewenste functie
te selecteren.
U kunt de volgende functies aanpassen.
# Als de MW/LW-band is geselecteerd, zijn alleen
BSM, LOCAL en SEEK beschikbaar.
Gebruik van het toestel
90
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (91,1)
FM SETTING (instellingen voor FM-geluidskwali-
teit)
De geluidskwaliteit kan worden aangepast aan het
signaal van de FM-band.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
! STANDARD Dit is de standaardinstelling.
! HI-FI In deze instelling wordt de hoge
kwaliteit van stereogeluid benadrukt.
! STABLE In deze instelling wordt de lage
ruis van monogeluid benadrukt.
BSM (geheugen voor de sterkste zenders)
Met de functie BSM (Best Stations Memory) kunt
u automatisch de zes sterkste zenders in het ge-
heugen opslaan. Deze worden opgeslagen in volg-
orde van signaalsterkte.
1 Druk op M.C. om de functie BSM in te schake-
len.
Druk nogmaals op M.C. om deze te annuleren.
REGIONAL (regionaal)
Als de functie AF is ingeschakeld, kan de regio-
nale functie gebruikt worden om het zoeken tot re-
gionale programmas te beperken.
1 Druk op M.C. om de regionale functie in of uit
te schakelen.
LOCAL (automatisch afstemmen op lokale zen-
ders)
Als deze functie is ingeschakeld, stemt het toestel
alleen af op zenders waarvan het signaal vol-
doende sterk is voor een goede ontvangst.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
FM: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
Als u het hoogste niveau selecteert, wordt al-
leen afgestemd op de sterkste zenders. Bij la-
gere niveaus wordt ook afgestemd op
zwakkere zenders.
TA (stand-by voor verkeersberichten)
1 Druk op M.C. om de functie Stand-by voor ver-
keersberichten in en uit te schakelen.
AF (alternatieve frequenties zoeken)
1 Druk op M.C. om AF aan of uit te zetten.
NEWS (onderbreking door nieuwsberichten)
1 Druk op M.C. om de nieuwsfunctie in of uit te
schakelen.
SEEK (instelling linker/rechter toets)
U kunt een functie toewijzen aan de linker en rech-
ter toets van het toestel.
Selecteer MAN (handmatig afstemmen) om hand-
matig af te stemmen of PCH (voorkeuzezenders)
om op voorkeuzezenders af te stemmen.
1 Druk op M.C. om MAN of PCH te selecteren.
Cd/cd-r/cd-rw-discs en USB-
opslagapparaten
MTP-verbinding
Android-apparaten die compatibel zijn met MTP
(apparaten met Android OS 4.0 of hoger) kun-
nen via de USB-bron met een MTP-verbinding
worden aangesloten. Sluit Android-apparaten
aan met de eigen kabel van het apparaat.
Opmerking
Deze functie is niet compatibel met WAV.
Basisbediening
Een cd/cd-r/cd-rw afspelen
1 Plaats een disc met het etiket omhoog in de
laadsleuf.
Een cd/cd-r/cd-rw uitwerpen
1 Druk op h.
Songs op een USB-opslagapparaat afspelen
1 Open het deksel van de USB-poort.
2 Sluit het USB-opslagapparaat aan via een
USB-kabel.
Stoppen met afspelen van songs op een USB -op-
slagapparaat
1 U kunt een USB-opslagapparaat op elk ge-
wenst moment verwijderen.
Een map selecteren
1 Druk op 1/
of 2/ .
Een fragment selecteren
1 Druk op c of d.
Vooruit of achteruit spoelen
1 Houd c of d ingedrukt.
! Als u gecomprimeerde audio afspeelt, is er
geen geluid bij vooruit- en achteruitspoelen.
Terugkeren naar de hoofdmap
1 Houd BAND/
ingedrukt.
Overschakelen tussen gecomprimeerde audio en
cd-da
1 Druk op BAND/
.
Overschakelen tussen afspeelbare geheugenappa-
raten
Als een USB-opslagapparaat meerdere USB Mass
Storage-compatibele afspeelbare geheugenappa-
raten bevat, kunt u tussen deze apparaten over-
schakelen.
1 Druk op BAND/
.
! U kunt overschakelen tussen maximaal 32 ver-
schillende geheugenapparaten.
Opmerking
Ontkoppel USB-opslagapparaten van dit toestel
wanneer u ze niet gebruikt.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
CD-DA
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
CD-TEXT
! TRACK INFO (fragmenttitel/naam artiest
fragment/disctitel)
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
MP3/WMA/WAV
! TRACK INFO (fragmenttitel/naam artiest/
albumtitel)
! FILE INFO (bestandsnaam/mapnaam)
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
Bestanden en fragmenten in de
lijst selecteren en afspelen
1 Druk op om over te schakelen naar de
lijst met bestands- of fragmentnamen.
2 Gebruik M.C. om de gewenste bestands-
naam (of mapnaam) te selecteren.
Een bestand of map selecteren
1 Draai aan M.C.
Afspelen
1 Selecteer een bestand of fragment en druk op
M.C.
Nederlands
Gebruik van het toestel
91
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (92,1)
Een lijst van de bestanden (mappen) in de gese-
lecteerde map weergeven
1 Selecteer een map en druk op M.C.
Een song in de geselecteerde map afspelen
1 Selecteer een map en houd M.C. ingedrukt.
Bediening met speciale toetsen
Een herhaalbereik selecteren
1 Druk op 6/
om over te schakelen tussen:
Cd/cd-r/cd-rw-discs
! ALL Alle fragmenten herhalen
! ONE Het huidige fragment herhalen
! FLD De huidige map herhalen
USB-opslagapparaat
! ALL Alle bestanden herhalen
! ONE Het huidige bestand herhalen
! FLD De huidige map herhalen
Fragmenten in willekeurige volgorde afspelen
1 Druk op 5/
om willekeurige weergave in of
uit te schakelen.
Fragmenten in een geselecteerd herhaalbereik
worden in willekeurige volgorde afgespeeld.
! Druk tijdens weergave in willekeurige volgorde
op d om naar het volgende fragment te gaan.
Als u op c drukt, wordt het huidige fragment
opnieuw vanaf het begin afgespeeld.
Het afspelen onderbreken
1 Druk op 4/PAUSE om het afspelen te onderbre-
ken (pauze) of te hervatten.
De geluidskwaliteit van gecomprimeerde audio
verbeteren (sound retriever)
1 Druk op 3/S.Rtrv om over te schakelen tussen:
12OFF (uit)
1 heeft effect bij lage compressie en 2 heeft ef-
fect bij hoge compressie.
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
U kunt de volgende functie aanpassen.
S.RTRV (sound retriever)
Deze verbetert automatisch de weergave van ge-
comprimeerde audio en zorgt voor een vol geluid.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
Raadpleeg De geluidskwaliteit van gecompri-
meerde audio verbeteren (sound retriever) op
bladzijde 92 voor meer informatie.
iPod
Basisbediening
Muziek op een iPod afspelen
1 Open het deksel van de USB-poort.
2 Sluit een iPod aan op de USB-ingang.
Het afspelen begint automatisch.
Een song selecteren (hoofdstuk)
1 Druk op c of d.
Een album selecteren
1 Druk op 1/
of 2/ .
Vooruit of achteruit spoelen
1 Houd c of d ingedrukt.
Opmerkingen
! De iPod kan niet worden in- en uitgeschakeld
als de bedieningsmodus is ingesteld op
CTRL AUDIO.
! Verwijder de koptelefoon van de iPod voordat
u hem op dit toestel aansluit.
! De iPod wordt uitgeschakeld ongeveer twee
minuten nadat de contactschakelaar is uitge-
zet.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! TRACK INFO (fragmenttitel/naam artiest/
albumtitel)
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
Naar een song bladeren
1 Druk op om naar het hoofdmenu met
zoeklijsten te gaan.
2 Selecteer een categorie of song met M.C.
De naam van een song of categorie wijzigen
1 Draai aan M.C.
Speellijstenartiestenalbumssongs
podcastsgenrescomponistenaudioboe-
ken
Afspelen
1 Selecteer een song en druk op M.C.
Een lijst van songs in de geselecteerde categorie
weergeven
1 Selecteer een categorie en druk op M.C.
Een song in de geselecteerde categorie afspelen
1 Selecteer een categorie en houd M.C. inge-
drukt.
Alfabetisch in een lijst zoeken
1 Geef de lijst voor de geselecteerde categorie
weer en druk op
om alfabetisch te zoeken.
! U kunt ook overschakelen naar alfabetisch
zoeken door twee keer aan M.C. te draaien.
2 Draai aan M.C. om een letter te selecteren.
3 Druk op M.C. om de alfabetische lijst weer te
geven.
! Druk op
/DIMMER om het zoeken te annu-
leren.
Opmerkingen
! U kunt speellijsten afspelen die zijn gemaakt
met de computertoepassing MusicSphere.
Deze toepassing is beschikbaar op onze web-
site.
! Speellijsten die zijn gemaakt met de compu-
tertoepassing MusicSphere worden verkort
weergegeven.
Bediening met speciale toetsen
Een herhaalbereik selecteren
1 Druk op 6/
om over te schakelen tussen:
! ONE De huidige song herhalen
! ALL Alle songs in de geselecteerde lijst
herhalen
! In de bedieningsmodus CTRL iPod wordt het-
zelfde herhaalbereik gebruikt dat is ingesteld
voor de aangesloten iPod.
Een herhaalbereik voor afspelen in willekeurige
volgorde (shuffle) selecteren
1 Druk op 5/
om over te schakelen tussen:
! SNG De songs in de geselecteerde lijst in
willekeurige volgorde afspelen.
! ALB De songs van een willekeurig album
op volgorde afspelen.
! OFF Niet afspelen in willekeurige volg-
orde.
Gebruik van het toestel
92
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (93,1)
Alle songs in willekeurige volgorde afspelen (shuf-
fle all)
1 Houd 5/
ingedrukt om de functie Shuffle
all in te schakelen.
! Selecteer OFF in Shuffle om Shuffle all uit te
schakelen. Raadpleeg voor meer informatie
Een herhaalbereik voor afspelen in willekeurige
volgorde (shuffle) selecteren op bladzijde 92.
Het afspelen onderbreken
1 Druk op 4/PAUSE om het afspelen te onderbre-
ken (pauze) of te hervatten.
De geluidskwaliteit van gecomprimeerde audio
verbeteren (sound retriever)
1 Druk op 3/S.Rtrv om over te schakelen tussen:
12OFF (uit)
1 heeft effect bij lage compressie en 2 heeft ef-
fect bij hoge compressie.
Songs afspelen die verwant zijn
met de huidige song
De volgende lijsten voor songs zijn beschikbaar.
Lijst van albums van de huidige artiest
Lijst van songs op het huidige album
Lijst van albums van het huidige genre
1 Houd
ingedrukt om naar de gekop-
pelde weergavemodus over te schakelen.
2 Draai aan M.C. om een andere modus te
kiezen; druk erop om een modus te selecte-
ren.
! ARTIST Een album van de huidige artiest af-
spelen.
! ALBUM Een song van het huidige album af-
spelen.
! GENRE Een album van het huidige genre af-
spelen.
De geselecteerde song of het geselecteerde
album wordt na de huidige song afgespeeld.
Opmerkingen
! De geselecteerde song of het geselecteerde
album kan worden geannuleerd als u een an-
dere functie dan gekoppeld zoeken gebruikt
(bijvoorbeeld snel vooruit of achteruit spoe-
len).
! Afhankelijk van de geselecteerde song is het
mogelijk dat het einde van de huidige song
en het begin van de geselecteerde song
(album) worden afgesneden.
De iPod-functie van dit toestel
via de iPod gebruiken
De iPod-functie van dit toestel kan via een aan-
gesloten iPod bediend worden.
CTRL iPod kan niet worden gebruikt met de vol-
gende iPod-modellen.
! iPod nano 1e generatie
! iPod met video
% Druk op BAND/
om de bedieningsmo-
dus te wijzigen.
! CTRL iPod De iPod-functie van dit toestel
kan via de aangesloten iPod bediend worden.
! CTRL AUDIO De iPod-functie van dit toestel
kan via dit toestel bediend worden.
U kunt ook op iPod drukken om de bedienings-
modus te wijzigen.
Opmerkingen
! Als u de bedieningsmodus overschakelt op
CTRL iPod, wordt het afspelen van songs on-
derbroken. Gebruik de iPod om de weergave
te hervatten.
! Ook als de bedieningsmodus is ingesteld op
CTRL iPod, kunnen de volgende functies
vanaf dit toestel bediend worden.
Pauze
Vooruit en achteruit spoelen
Een song selecteren (hoofdstuk)
! Het volume kan alleen vanaf dit toestel wor-
den bijgesteld.
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
3 Draai aan M.C. om de gewenste functie
te selecteren.
U kunt de volgende functies aanpassen.
! AUDIO BOOK kan niet worden gebruikt als
CTRL iPod is geselecteerd in de bedienings-
modus. Raadpleeg De iPod-functie van dit toe-
stel via de iPod gebruiken op bladzijde 93 voor
meer informatie.
AUDIO BOOK (audioboeksnelheid)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
! FASTER Weergave is sneller dan normaal
! NORMAL Weergave met normale snel-
heid
! SLOWER Weergave is langzamer dan
normaal
S.RTRV (sound retriever)
1 Druk op M.C. en selecteer de gewenste instel-
ling.
Raadpleeg De geluidskwaliteit van gecompri-
meerde audio verbeteren (sound retriever) op
bladzijde 93 voor meer informatie.
Applicaties van aangesloten
apparaten gebruiken
Via dit toestel kunt u songs van iPhone-applica-
ties via streaming afspelen en bedienen of al-
leen via streaming afspelen.
Belangrijk
Voor gebruik van applicaties van derden wor-
den mogelijk persoonsgegevens gebruikt of
moet u zulke gegevens verstrekken, bijvoor-
beeld door het opzetten van een gebruikersac-
count of op andere wijze, en voor sommige
applicaties worden mogelijk geolocatiegege-
vens gebruikt.
ALLE APPLICATIES VAN DERDEN VALLEN
UITSLUITEND ONDER VERANTWOORDELIJK-
HEID VAN HUN UITGEVER, INCLUSIEF MAAR
NIET BEPERKT TOT HET VERZAMELEN EN
BEVEILIGEN VAN GEBRUIKERSGEGEVENS
EN HET PRIVACYBELEID. DOOR EEN APPLI-
CATIE VAN DERDEN TE GEBRUIKEN, GAAT U
ERMEE AKKOORD OM U TE INFORMEREN
OVER DE GEBRUIKSVOORWAARDEN EN
HET PRIVACYBELEID VAN DE UITGEVER
ERVAN. ALS U NIET AKKOORD GAAT MET
DE GEBRUIKSVOORWAARDEN OF HET BE-
LEID VAN EEN UITGEVER OF GEEN TOE-
STEMMING GEEFT VOOR HET GEBRUIK VAN
GEOLOCATIEGEGEVENS (INDIEN VAN TOE-
PASSING), MOET U DE APPLICATIE NIET GE-
BRUIKEN.
Informatie over de compatibiliteit
van aangesloten apparaten
Hieronder vindt u gedetailleerde informatie over
de benodigde aansluitingen om de applicatie
voor iPhone op dit toestel te gebruiken.
Voor iPhone
! Deze functie is compatibel met de iPhone en
iPod touch.
! Het apparaat moet iOS 5.0 of later hebben.
Opmerkingen
! Raadpleeg onze website voor een overzicht
van ondersteunde iPhone-applicaties voor dit
toestel.
Nederlands
Gebruik van het toestel
93
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (94,1)
! Pioneer is niet aansprakelijk voor problemen
die kunnen ontstaan door fouten of gebreken
in de gebruikte toepassing.
! De provider van de App is verantwoordelijk
voor de inhoud en de functionaliteit van de
aangeboden toepassing.
Startprocedure voor iPhone
1 Sluit een iPhone aan op de USB-ingang.
2 Schakel de signaalbron over naar APP.
3 Start de applicatie op de iPhone en begin
met afspelen.
Basisbediening
Een fragment selecteren
1 Druk op c of d.
Vooruit of achteruit spoelen
1 Houd c of d ingedrukt.
Het afspelen onderbreken
1 Druk op BAND/
om het afspelen te onder-
breken (pauze) of te hervatten.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! TRACK INFO (fragmenttitel/naam artiest/
albumtitel)
! APP NAME (naam van applicatie)
! ELAPSED TIME (weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
3 Draai aan M.C. om de gewenste functie
te selecteren.
U kunt de volgende functies aanpassen.
PAUSE (pauze)
1 Druk op M.C. om het afspelen te onderbreken
(pauze) of te hervatten.
S.RTRV (sound retriever)
1 Druk op M.C. en selecteer de gewenste instel-
ling.
12OFF (uit)
1 heeft effect bij lage compressie en 2 heeft ef-
fect bij hoge compressie.
Audio-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
AUDIO en druk erop.
3 Draai aan M.C. en selecteer de audiofunc-
tie.
U kunt de volgende audiofuncties aanpassen.
! FADER kan niet worden gebruikt als
SUB.W/SUB.W is geselecteerd in
SP-P/O MODE. Raadpleeg voor meer infor-
matie SP-P/O MODE (achteruitgang en
preout-instelling) op bladzijde 96.
! SUB.W en SUB.W CTRL kunnen niet worden
gebruikt als REAR/REAR is geselecteerd in
SP-P/O MODE. Raadpleeg voor meer infor-
matie SP-P/O MODE (achteruitgang en
preout-instelling) op bladzijde 96.
! SUB.W CTRL kan niet worden gebruikt als
SUB.W is geselecteerd in OFF. Raadpleeg
voor meer informatie SUB.W (subwoofer aan/
uit) op bladzijde 94.
! SLA is niet beschikbaar als de signaalbron is
ingesteld op FM.
FADER (fader aanpassen)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de balans tussen de luid-
sprekers voorin en achterin in te stellen.
BALANCE (balansinstelling)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de balans tussen de linker/
rechterluidsprekers in te stellen.
EQ SETTING (equalizercurven)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de equalizer te selecteren.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
De equalizerband en het equalizerniveau kun-
nen worden aangepast van CUSTOM1 en
CUSTOM2.
Volg de onderstaande procedure als u CUS-
TOM1 of CUSTOM2 selecteert. Voor een an-
dere optie drukt u op M.C. om terug te keren
naar het vorige display.
! CUSTOM1 kan voor elke signaalbron af-
zonderlijk worden ingesteld. USB, iPod en
APP worden echter automatisch op de-
zelfde stand ingesteld.
! CUSTOM2 is een gemeenschappelijk in-
stelling voor alle signaalbronnen.
3 Druk op M.C. om de instellingenmodus weer
te geven.
4 Druk op M.C. om over te schakelen tussen:
EqualizerbandEqualizerniveau
5 Draai aan M.C. en selecteer de gewenste in-
stelling.
Equalizerband: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizerniveau: +6 tot 6
LOUDNESS (loudness)
De loudness-functie compenseert een tekort aan
lage tonen en hoge tonen bij een laag volume.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
OFF (uit)LOW (laag)MID (midden)HI
(hoog)
SUB.W (subwoofer aan/uit)
Dit toestel is voorzien van een in- en uitschakel-
bare subwooferuitgang.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
NOR (normale fase)REV (tegengestelde
fase)OFF (subwoofer uit)
Gebruik van het toestel
94
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (95,1)
SUB.W CTRL (subwoofer aanpassen)
De subwoofer geeft alleen frequenties beneden de
geselecteerde waarde weer.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om over te schakelen tussen:
DrempelfrequentieUitgangsniveauVerval-
niveau
Instelbare waarden knipperen.
3 Draai aan M.C. en selecteer de gewenste in-
stelling.
Drempelfrequentie: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Uitgangsniveau: 24 tot +6
Hellingsniveau: 12 24
BASS BOOST (bass boost)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer het gewenste ni-
veau.
U kunt het niveau verhogen of verlagen tussen
de waarden 0 en +6. De waarde wordt op het
display getoond.
HPF SETTING (high pass filter aanpassen)
Gebruik deze functie als u alleen naar geluid met
hogere frequenties wilt luisteren. Alleen frequen-
ties boven de drempelfrequentie van het high pass
filter worden weergegeven.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om over te schakelen tussen:
DrempelfrequentieVervalniveau
3 Draai aan M.C. en selecteer de gewenste in-
stelling.
Drempelfrequentie: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Hellingsniveau: 12 24
SLA (bronniveauregeling)
De functie voorkomt sterke volumewisselingen
wanneer de bron wordt overgeschakeld.
! De instellingen zijn gebaseerd op het FM-volu-
meniveau, dat zelf niet gewijzigd kan worden.
! Het MW/LW-volumeniveau kan ook met deze
functie worden aangepast.
! USB, iPod en APP worden automatisch het-
zelfde ingesteld.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om het bronvolume te regelen.
Instelbereik: +4 tot 4
Systeemmenu
Belangrijk
Als het toestel van de accu wordt losgekoppeld,
wordt PW SAVE (energiezuinige modus) uitge-
schakeld. Deze functie moet u weer inschakelen
als het toestel terug met de accu wordt verbon-
den. Als het voertuig niet van een contactscha-
kelaar met accessoirestand (ACC) is voorzien, is
het (afhankelijk van de aansluiting) mogelijk dat
het toestel de accu blijft belasten als PW SAVE
(energiezuinige modus) is uitgeschakeld.
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
3 Draai aan M.C. en selecteer de systeem-
menufunctie.
U kunt de volgende functies in het systeemme-
nu aanpassen.
LANGUAGE (taalinstelling)
1 Druk op M.C. en selecteer de gewenste instel-
ling.
ENG (Engels)РУС (Russisch)TUR (Turks)
CLOCK SET (klok)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om het onderdeel van de klok te
selecteren dat u wilt instellen.
UurMinuut
3 Draai aan M.C. om de klok in te stellen.
12H/24H (tijdweergave)
1 Druk op M.C. en selecteer de gewenste instel-
ling.
12H (12-uurs klok)24H (24-uurs klok)
AUTO PI (automatisch PI-zoeken)
Als deze functie is ingeschakeld, probeert het toe-
stel bij slechte ontvangst automatisch een andere
zender met gelijkaardige programmas te vinden,
ook als u een voorkeuzezender selecteerde.
1 Druk op M.C. om de automatische PI-zoek-
functie in of uit te schakelen.
AUX (externe aansluiting)
Schakel deze instelling in als een extern apparaat
op dit toestel is aangesloten.
1 Druk op M.C. om AUX in of uit te schakelen.
DIMMER (dimmer)
1 Druk op M.C. om de dimmer in of uit te scha-
kelen.
! U kunt de dimmer ook instellen door
/DIM-
MER even ingedrukt te houden.
MUTE MODE (dempen)
Het geluid van dit toestel kan automatisch worden
uitgeschakeld of gedempt wanneer een ander ap-
paraat met uitschakelingsfunctie daarom vraagt
met een speciaal signaal.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
! MUTE Tijdelijk uitschakelen
! 20dB ATT Dempen (20dB ATT heeft
meer effect dan 10dB ATT)
! 10dB ATT Dempen
PW SAVE (energiezuinige stand)
Met deze functie wordt het energieverbruik van de
accu verminderd.
! Als deze functie is ingeschakeld, kan alleen
het bronsignaal worden ingeschakeld.
1 Druk op M.C. om de energiezuinige modus in
of uit te schakelen.
Beginmenu
1 Houd SRC/OFF ingedrukt tot het toestel
uit gaat.
2 Houd SRC/OFF ingedrukt tot het hoofd-
menu wordt weergegeven.
3 Draai aan M.C., selecteer de menuoptie
INITIAL en druk erop.
4 Draai aan M.C. en selecteer de gewenste
functie.
U kunt de volgende functies in het beginmenu
aanpassen.
FM STEP (FM-afstemstap)
1 Druk op M.C. om de FM-afstemstap te selecte-
ren.
100 (100 kHz)50 (50 kHz)
Nederlands
Gebruik van het toestel
95
Hoofdstuk
Gebruik van het toestel
Nl
02
Black plate (96,1)
SP-P/O MODE (achteruitgang en preout-instel-
ling)
Op de uitgang voor de achterluidspreker en de
RCA-uitgang van dit toestel kan een luidspreker
met volledig bereik of een subwoofer aangesloten
worden. Selecteer de gewenste instelling.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
! REAR/SUB.W Selecteer deze stand als
op de uitgang voor de achterluidspreker
een luidspreker met volledig bereik aange-
sloten is, en op de RCA-uitgang een sub-
woofer aangesloten is.
! SUB.W/SUB.W Selecteer deze stand als
op de uitgang voor de achterluidspreker
een subwoofer rechtstreeks aangesloten is
zonder versterker, en op de RCA-uitgang
een subwoofer is aangesloten.
! REAR/REAR Selecteer deze stand als op
de uitgang voor de achterluidspreker en op
de RCA-uitgang een luidspreker met volle-
dig bereik is aangesloten.
Als op de uitgang voor de achterluidspre-
ker een luidspreker met volledig bereik is
aangesloten en de RCA-uitgang niet ge-
bruikt wordt, kunt u zowel REAR/SUB.W
als REAR/REAR selecteren.
Systeemmenu
1 Houd SRC/OFF ingedrukt tot het toestel
uit gaat.
2 Houd SRC/OFF ingedrukt tot het hoofd-
menu wordt weergegeven.
3 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
4 Draai aan M.C. en selecteer de systeem-
menufunctie.
Raadpleeg Systeemmenu op bladzijde 95 voor
meer informatie.
De AUX-signaalbron
1 Steek de stereo-miniplugkabel in de
AUX-ingang van dit toestel.
2 Druk op SRC/OFF en kies AUX als signaal-
bron.
Opmerking
De signaalbron AUX kan alleen worden geselec-
teerd als de externe aansluiting is ingeschakeld.
Raadpleeg voor meer informatie AUX (externe
aansluiting) op bladzijde 95.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! Naam signaalbron
! Naam signaalbron en klok
Als een scherm verkeerd
wordt weergegeven
Zet het ongewenste scherm als volgt uit.
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
3 Draai aan M.C., geef DEMO OFF weer en
druk erop.
4 Draai aan M.C. en selecteer YES.
5 Druk op M.C. om uw keuze te bevesti-
gen.
Verbindingen
Belangrijk
! Als dit toestel wordt geïnstalleerd in een voer-
tuig met een contactschakelaar zonder ACC-
stand (accessoirestand), kan de accu leeglo-
pen als de rode kabel niet wordt aangesloten
op de aansluiting die de bediening van de
contactschakelaar herkent.
O
N
S
T
A
R
T
O
F
F
ACC-stand Geen ACC-stand
! Gebruik van dit toestel onder andere omstan-
digheden dan de volgende kan leiden tot
brand of storingen.
Voertuigen met een accu van 12 volt en nega-
tieve aarding.
Luidsprekers van 50 W (uitgangswaarde) en
4 W tot 8 W (impedantiewaarde).
! Om kortsluiting, oververhitting en storingen
te voorkomen, moet u onderstaande aanwij-
zingen opvolgen.
Koppel de negatieve aansluiting van de accu
los voordat u het toestel installeert.
Gebruik kabelklemmen of plakband om de
bekabeling veilig aan te brengen. Bescherm
de kabels met plakband op plaatsen waar
deze tegen metalen onderdelen liggen.
Plaats geen kabels in de buurt van beweeg-
bare onderdelen zoals de versnellingspook of
de stoelrails.
Leg kabels niet op plaatsen die heet kunnen
worden, zoals dicht bij de kachel.
Sluit de gele kabel niet op de accu aan via
een gat in het motorcompartiment.
Dek alle ongebruikte kabelaansluitingen af
met isolatietape.
Maak de kabels niet korter.
Verwijder nooit de isolatie van de voedingska-
bel van dit toestel om andere apparaten van
stroom te voorzien. De stroomcapaciteit van
de voedingskabel is beperkt.
Gebruik een zekering met het voorgeschreven
vermogen.
Verbind de negatieve luidsprekerkabel nooit
rechtstreeks met de aarding.
Voeg de negatieve kabels van verschillende
luidsprekers nooit samen.
! Als dit apparaat aan staat, wordt het bedie-
ningssignaal doorgegeven via de blauw/witte
kabel. Verbind deze kabel met de afstandsbe-
diening van een externe versterker of met de
bedieningsaansluiting van de automatische
antenne van het voertuig (maximaal 300 mA,
12 V gelijkstroom). Als het voertuig is uitge-
rust met een glasantenne, verbindt u deze
met de voedingsaansluiting van de antenne-
booster.
! Verbind de blauw/witte kabel nooit met de
voedingsaansluiting van een externe verster-
ker of automatische antenne. Anders kan de
accu leeglopen of kan er storing optreden.
! De zwarte kabel is de aarding. Dit toestel
moet gescheiden worden geaard van andere
apparaten (met name apparaten die veel
stroom verbruiken zoals een versterker). An-
ders kan er brand of storing ontstaan wan-
neer de aarding per ongeluk losraakt.
Dit toestel
3
1 24
5
1 Antenne-ingang
2 Zekering (10 A)
3 Ingang stroomkabel
Gebruik van het toestel
96
Hoofdstuk
Installatie
Nl
02
03
Black plate (97,1)
4 Ingang voor draadafstandsbediening
Een bedrade afstandsbedieningsadapter kan
aangesloten worden (los verkrijgbaar).
5 Achteruitgang of subwooferuitgang
Stroomkabel
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Naar ingang stroomkabel
2 De functie van 3 en 5 kan verschillen af-
hankelijk van het type voertuig. Verbind in
dat geval 4 met 5 en 6 met 3.
3 Geel
Back-up (of accessoire)
4 Geel
Aansluiten op de constante 12 V-voedings-
aansluiting.
5 Rood
Accessoire (of back-up)
6 Rood
Aansluiten op een aansluiting die door de
contactschakelaar wordt aangestuurd (12 V
gelijkstroom).
7 Verbind kabels van dezelfde kleur met elkaar.
8 Zwart (chassisaarding)
9 Blauw-wit
De pinpositie van de ISO-connector verschilt
naargelang het type voertuig. Als pin 5 de an-
tenne aanstuurt, verbindt u 9 en b. In an-
dere typen voertuigen verbindt u 9 en b
nooit.
a Blauw-wit
Aansluiten op systeembedieningsaansluiting
van de versterker (maximaal 300 mA, 12 V ge-
lijkstroom).
b Blauw-wit
Aansluiten op bedieningsaansluiting van de
gemotoriseerde antenne (maximaal 300 mA,
12 V gelijkstroom).
c Geel/zwart
Als u apparatuur met dempingsfunctie ge-
bruikt, verbindt u deze draad met de draad
voor audiodemping op die apparatuur. Als u
zulke apparatuur niet gebruikt, verbindt u de
draad voor audiodemping niet.
d Luidsprekerkabels
Wit: Linksvoor +
Wit-zwart: Linksvoor *
Grijs: Rechtsvoor +
Grijs-zwart: Rechtsvoor *
Groen: Linksachter + of subwoofer +
Groen-zwart: Linksachter * of subwoofer *
Violet: Rechtsachter + of subwoofer +
Violet-zwart: Rechtsachter * of subwoofer *
e ISO-connector
Bij sommige voertuigen is de ISO-connector
in twee verdeeld. Verbind in dat geval beide
connectoren.
Opmerkingen
! Wijzig het beginmenu van het toestel. Raad-
pleeg gedeelte SP-P/O MODE (achteruitgang
en preout-instelling) op bladzijde 96.
De subwooferuitgang van dit toestel is mono.
! Als u een subwoofer van 70 W (2 W) gebruikt,
moet u de subwoofer aansluiten op de vio-
lette en zwart-violette draden van dit toestel.
Sluit niets aan op de groene en groen-zwarte
draden.
Versterker (apart verkrijgbaar)
Maak deze verbindingen als de optionele verster-
ker wordt gebruikt.
1
3
2
4
55
1 Systeemafstandsbediening
Verbinden met blauw-witte kabel.
2 Versterker (apart verkrijgbaar)
3 Aansluiten op RCA-kabels (apart verkrijg-
baar)
4 Naar achteruitgang of subwooferuitgang
5 Luidspreker achterin of subwoofer
Installatie
Belangrijk
! Controleer alle aansluitingen en systemen
voordat u de installatie voltooit.
! Gebruik geen onderdelen van andere fabri-
kanten; deze kunnen storingen veroorzaken.
! Neem contact op met uw dealer als er voor
de installatie gaten moeten worden geboord
of als er andere aanpassingen aan het voer-
tuig nodig zijn.
! Installeer dit toestel niet op een plaats waar:
het de besturing van het voertuig kan belem-
meren.
het de inzittenden kan verwonden bij een
noodstop.
! De halfgeleiderlaser raakt bij oververhitting
beschadigd. Plaats dit apparaat niet op plaat-
sen waar het warm wordt, zoals nabij de uit-
laat van een kachel.
! Dit toestel werkt het beste als het wordt ge-
plaatst onder een hoek van minder dan 60°.
60°
! Laat bij het plaatsen voldoende ruimte vrij
achter het achterpaneel en wikkel losse ka-
bels zo dat ze de ventilatiegaten niet blokke-
ren; zorg altijd dat warmte goed wordt
afgevoerd tijdens gebruik van het toestel.
5cmcm
Laat voldoende
ruimte vrij
5 cm
5 cm
! Gebruik voor installatie in de handel verkrijg-
bare onderdelen.
Installatie
Het toestel kan op een van de volgende wijzen
geïnstalleerd worden.
! Installatie met de houder
! Monteren met de schroefgaten aan de zijkant
van het toestel
Nederlands
Installatie
97
Hoofdstuk
Installatie
Nl
03
Black plate (98,1)
Voordat u het toestel monteert
1 Verwijder de sierlijst.
1
1 Sierlijst
2 Steek de meegeleverde uittreksleutels in
de beide kanten van het toestel totdat ze op
hun plaats klikken.
3 Trek het toestel uit de houder.
Verwijder de houder.
1
1 Houder
(meegeleverd onderdeel)
Installatie met de houder
1 Monteer de houder in het dashboard.
Nadat u de houder in het dashboard geplaatst
hebt, kiest en buigt u lipjes die geschikt zijn voor
de dikte van het dashboardmateriaal. (Monteer
dit toestel zo stevig mogelijk met behulp van de
boven- en onderlipjes. Om het toestel vast te zet-
ten, buigt u de lipjes 90 graden.)
1
2
1 Dashboard
2 Houder
(meegeleverd onderdeel)
2 Installeer het toestel.
1
1 Dashboard
3 Bevestig de sierlijst.
1
1 Sierlijst
De houder verwijderen
De procedure is gelijk aan die in Voordat u het
toestel monteert. Raadpleeg voor meer informa-
tie Voordat u het toestel monteert op bladzijde
98.
Monteren met de schroefgaten
aan de zijkant van het toestel
% Bevestig het toestel aan de radiomonta-
geklem.
Plaats het toestel zo dat de schroefgaten ervan
samenvallen met de schroefgaten van de klem.
Zet het toestel vast met drie schroeven aan elke
kant.
1
2
4
3
1 Als het uitsteekseltje in de weg zit, buigt u het
omlaag.
2 Radiomontageklem
3 Platbolkopschroeven (5 mm × 8 mm)
4 Dashboard of console
Installatie
98
Hoofdstuk
Installatie
Nl
03
Black plate (99,1)
Problemen verhelpen
Symptomen worden vet gedrukt. Oorzaken wor-
den in gewoon lettertype zonder inspringen ge-
drukt. Gewone en ingesprongen tekst geeft aan
wat u moet doen.
Het display keert automatisch terug naar het
gewone display.
U hebt gedurende ongeveer 30 seconden geen han-
deling uitgevoerd.
Voer de handeling opnieuw uit.
Het bereik voor herhaald afspelen wordt onver-
wachts gewijzigd.
Afhankelijk van het herhaalbereik kan het geselec-
teerde bereik gewijzigd worden wanneer u een an-
dere map of een ander fragment selecteert of vooruit
of achteruit spoelt.
Selecteer het gewenste herhaalbereik opnieuw.
Een onderliggende map wordt niet afgespeeld.
Onderliggende mappen worden niet afgespeeld wan-
neer FLD (map herhalen) is geselecteerd.
Selecteer een ander herhaalbereik.
Als het display wordt gewijzigd, verschijnt
NO XXXX (bijvoorbeeld NO TITLE).
Er is geen tekstinformatie beschikbaar.
Wijzig de displaystand of speel een ander
fragment of bestand af.
Het toestel functioneert niet correct.
Er is interferentie.
U gebruikt mogelijk een apparaat (bijvoorbeeld een
mobiele telefoon) dat hoorbare interferentie veroor-
zaakt.
Gebruik nabij dit toestel geen elektrische
apparaten die interferentie kunnen veroorzaken.
Foutmeldingen
Schrijf een foutmelding altijd nauwkeurig op en
houd die bij de hand als u contact opneemt met
uw leverancier of Pioneer-servicecentrum.
Foutmeldingen worden vet gedrukt. Oorzaken
worden in gewoon lettertype zonder inspringen
gedrukt. Gewone, ingesprongen tekst geeft aan
wat u moet doen.
Algemeen
AMP ERROR
Dit toestel werkt niet of er is een probleem met de
luidsprekeraansluiting; het beveiligingscircuit is ge-
activeerd.
Controleer de luidsprekeraansluiting. Neem
contact op met uw leverancier of een erkend
Pioneer Servicecentrum als het bericht nog
wordt weergegeven nadat u de motor hebt uit- en
aangezet.
Cd-speler
ERROR-07, 11, 12, 17, 30
De disc is vuil.
Reinig de disc.
De disc is bekrast.
Plaats een andere disc.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Elektrisch of mechanisch probleem.
Zet het contact uit en weer aan, of schakel over
naar een andere signaalbron en dan terug naar
de cd-speler.
ERROR-15
De geplaatste disc bevat geen gegevens.
Plaats een andere disc.
ERROR-23
Het cd-formaat wordt niet ondersteund.
Plaats een andere disc.
FORMAT READ
Na het begin van het afspelen duurt het soms even
totdat er geluid klinkt.
Wacht tot het bericht verdwijnt en er geluid
klinkt.
NO AUDIO
De geplaatste disc bevat geen afspeelbare bestan-
den.
Plaats een andere disc.
SKIPPED
De geplaatste disc bevat bestanden die door digitaal
rechtenbeheer (DRM) beveiligd zijn.
Beveiligde bestanden worden overgeslagen.
PROTECT
Alle bestanden op de disc zijn door digitaal rechten-
beheer (DRM) beveiligd.
Plaats een andere disc.
USB-opslagapparaat en iPod
FORMAT READ
Na het begin van het afspelen duurt het soms even
totdat er geluid klinkt.
Wacht tot het bericht verdwijnt en er geluid
klinkt.
NO AUDIO
Er zijn geen songs.
Zet de audiobestanden over naar het USB-
opslagapparaat en sluit het aan.
De inhoud van het USB-opslagapparaat is beveiligd.
Raadpleeg de instructies bij het USB-
opslagapparaat om de beveiliging uit te
schakelen.
SKIPPED
Het aangesloten USB-opslagapparaat bevat bestan-
den die met DRM zijn beveiligd.
Beveiligde bestanden worden overgeslagen.
PROTECT
Alle bestanden op het aangesloten USB-opslagappa-
raat zijn beveiligd met DRM.
Gebruik een ander USB-opslagapparaat.
N/A USB
Het aangesloten USB-apparaat wordt niet onder-
steund door dit toestel.
! Gebruik een opslagapparaat dat compatibel is
met USB Mass Storage Class.
! Ontkoppel het apparaat en sluit een
compatibel USB-opslagapparaat aan.
CHECK USB
Er is kortsluiting opgetreden in de USB-aansluiting
of de USB-kabel.
Controleer of de USB-stekker en de USB-kabel
niet ergens ingeklemd of beschadigd zijn.
CHECK USB
Het aangesloten USB-opslagapparaat verbruikt meer
stroom dan de maximaal toelaatbare waarde.
Ontkoppel het USB-opslagapparaat en gebruik
het niet meer. Zet de contactschakelaar van het
voertuig uit, dan in de accessoirestand (ACC) of
aan, en sluit een compatibel USB-
opslagapparaat aan.
Nederlands
Aanvullende informatie
99
Aanhangsel
Aanvullende informatie
Nl
Black plate (100,1)
CHECK USB
De iPod functioneert correct maar wordt niet opgela-
den.
Controleer of de kabel van de iPod niet is
kortgesloten, bijvoorbeeld contact maakt met
metalen voorwerpen. Zet daarna het contact uit
en weer aan, of ontkoppel de iPod en sluit deze
weer aan.
ERROR-19
Communicatiefout.
Probeer de volgende mogelijkheden.
Zet het contact uit en dan weer aan.
Ontkoppel het USB-opslagapparaat.
Schakel over naar een andere signaalbron.
Schakel vervolgens terug naar de USB -
signaalbron.
iPod-fout.
Verwijder de kabel uit de iPod. Sluit de kabel
weer aan als het hoofdmenu van de iPod wordt
weergegeven en stel de iPod opnieuw in.
ERROR-23
Het USB-opslagapparaat was niet geformatteerd
met de indeling FAT12, FAT16 of FAT32.
Gebruik een USB-opslagapparaat dat
geformatteerd is met de indeling FAT12, FAT16 of
FAT32.
ERROR-16
De versie van de iPod-firmware is verouderd.
Werk de versie van de iPod bij.
iPod-fout.
Verwijder de kabel uit de iPod. Sluit de kabel
weer aan als het hoofdmenu van de iPod wordt
weergegeven en stel de iPod opnieuw in.
STOP
De huidige lijst bevat geen songs.
Selecteer een lijst die wel songs bevat.
NOT FOUND
Geen verwante songs.
Zet songs over naar de iPod.
Applicatie
START UP APP
De applicatie is nog niet gestart.
Volg de instructies op het scherm.
Aanwijzingen voor het gebruik
Discs en de player
Gebruik uitsluitend discs die voorzien zijn van een
van onderstaande twee logos.
Gebruik discs van 12 cm.
Gebruik uitsluitend normale, ronde discs.
De volgende typen discs kunnen niet op dit toestel
worden afgespeeld:
! DualDiscs
! Discs van 8 cm: Als u deze discs met een
adapter probeert af te spelen, kan het toestel
defect raken.
! Discs in een ongewone vorm
! Andere discs dan cds
! Beschadigde discs, inclusief schijven die zijn
gebarsten, gebogen of waarvan stukjes zijn af-
gebroken
! Cd-r/rw-discs die niet zijn gefinaliseerd
Raak de gegevenszijde van de disc niet aan.
Bewaar discs in het bijbehorende doosje wanneer
u ze niet gebruikt.
Plak geen labels op discs, schrijf er niet op en
breng het oppervlak niet in aanraking met chemi-
sche middelen.
Als u een cd reinigt, veegt u de disc van het mid-
den naar de buitenkant met een zachte doek
schoon.
Condens en vocht kunnen de werking van de spe-
ler tijdelijk negatief beïnvloeden. Laat de speler in
een warmere omgeving ongeveer een uur op tem-
peratuur komen. Veeg vochtige schijven met een
zachte doek schoon.
Sommige discs kunnen niet worden afgespeeld af-
hankelijk van het type disc, de indeling ervan, de
toepassing waarmee deze is opgenomen, de om-
geving waarin deze wordt afgespeeld, de manier
waarop deze wordt bewaard, enzovoort.
Schokken tijdens het rijden van het voertuig kun-
nen de disc laten overslaan.
Bij gebruik van discs met een bedrukbaar labelop-
pervlak moet u de instructies en waarschuwingen
van de discs controleren. Afhankelijk van de disc
kan laden of uitwerpen niet mogelijk zijn. Het ge-
bruik van zulke discs kan dit toestel beschadigen.
Plak geen in de handel verkrijgbare labels of an-
dere materialen op de discs.
! De discs kunnen vervormen waardoor ze onaf-
speelbaar kunnen worden.
! De labels kunnen loslaten tijdens het afspelen
en de disc blokkeren bij het uitwerpen en het
toestel beschadigen.
USB-opslagapparaat
Het maken van verbindingen via een USB-hub
wordt niet ondersteund.
Sluit alleen een USB-opslagapparaat aan en geen
andere apparaten.
Maak het USB-opslagapparaat stevig vast voordat
u gaat rijden. Zorg dat het niet op de grond valt
omdat het dan onder het rem- of gaspedaal te-
recht kan komen.
Afhankelijk van het USB-opslagapparaat kunnen
de volgende problemen voorkomen.
! De bediening kan verschillend zijn.
! Het opslagapparaat wordt niet herkend.
! Bestanden worden niet correct afgespeeld.
! Het toestel kan hoorbare interferentie veroorza-
ken wanneer u naar de radio luistert.
iPod
Stel de iPod niet bloot aan hoge temperaturen.
Maak de iPod stevig vast voordat u gaat rijden.
Zorg dat de iPod niet op de grond kan vallen
omdat hij dan onder het rem- of gaspedaal terecht
kan komen.
Informatie over iPod-instellingen
! Wanneer een iPod is aangesloten, wordt de
equalizer van de iPod door dit toestel uitge-
schakeld voor een optimale klankweergave.
Als u de iPod loskoppelt, wordt de equalizer
naar de oorspronkelijke instelling teruggezet.
! Tijdens gebruik van dit toestel kunt u de her-
haalfunctie op de iPod niet uitschakelen. De
herhaalfunctie wordt automatisch ingesteld op
Alle als u de iPod op dit toestel aansluit.
Tekst op de iPod die niet compatibel is met de spe-
cificaties van dit toestel kan niet worden weerge-
geven.
Aanvullende informatie
100
Aanhangsel
Aanvullende informatie
Nl
Black plate (101,1)
Compatibiliteit met
gecomprimeerde audio
(disc, USB)
WMA
Bestandsextensie: .wma
Bitsnelheid: 48 kbps tot 320 kbps (CBR), 48 kbps
tot 384 kbps (VBR)
Bemonsteringsfrequentie: 32 kHz, 44,1 kHz, 48 kHz
Windows Mediaä Audio Professional, Lossless,
Voice/DRM Stream/Stream met video: Niet com-
patibel
MP3
Bestandsextensie: .mp3
Bitsnelheid: 8 kbps tot 320 kbps (CBR), VBR
Bemonsteringsfrequentie: 8 kHz tot 48 kHz
(32 kHz, 44,1 kHz, 48 kHz voor de beste kwaliteit)
Compatibele ID3-tag-versie: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3-tag versie 2.x krijgt prioriteit boven versie 1.x.)
M3u speellijst: Niet compatibel
MP3i (MP3 interactive), mp3 PRO: Niet compati-
bel
WAV
Bestandsextensie: .wav
Quantisatiebits: 8 en 16 (LPCM), 4 (MS ADPCM)
Bemonsteringsfrequentie: 16 kHz tot 48 kHz
(LPCM), 22,05 kHz en 44,1 kHz (MS ADPCM)
! U kunt deze functie niet gebruiken met
USB MTP.
Bijkomende informatie
Alleen de eerste 32 tekens van de bestandsnaam
(inclusief de extensie) of mapnaam worden weer-
gegeven.
Russische tekst kan alleen op dit toestel worden
weergegeven als die met een van de volgende te-
kensets is gecodeerd:
! Unicode (UTF-8, UTF-16)
! Andere tekensets dan Unicode die in een
Windows-omgeving worden gebruikt en op
Russisch zijn ingesteld bij de taalinstellingen
Een juiste werking van dit toestel is afhankelijk
van de toepassing waarmee de WMA-bestanden
zijn gecodeerd.
Er kan een beetje vertraging optreden bij het be-
ginnen met afspelen van audiobestanden met
beeldgegevens of bestanden op een USB-opslag-
apparaat met een uitgebreide mappenstructuur.
Disc
Mappenhiërarchie: maximaal acht niveaus diep
(Voor praktisch gebruik kunt u beter niet meer dan
twee niveaus gebruiken.)
Afspeelbare mappen: maximaal 99
Afspeelbare bestanden: maximaal 999
Bestandssysteem: ISO 9660 Level 1 en 2, Romeo,
Joliet
Afspelen van multisessie-discs: Compatibel
Packet write data transfer: Niet compatibel
Bij het afspelen van gecomprimeerde audiodiscs
wordt altijd een korte pauze ingelast tussen de
fragmenten. Dit gebeurt ongeacht de duur tussen
de fragmenten op de originele opname.
USB-opslagapparaat
Mappenhiërarchie: maximaal acht niveaus diep
(Voor praktisch gebruik kunt u beter niet meer dan
twee niveaus gebruiken.)
Afspeelbare mappen: maximaal 500
Afspeelbare bestanden: maximaal 15 000
Afspelen van auteursrechtelijk beschermde be-
standen: Niet compatibel
Gepartitioneerd USB-opslagapparaat: Alleen de
eerste partitie kan worden afgespeeld.
Bij het starten van audiobestanden op een USB-
opslagapparaat met een uitgebreide mappen-
structuur kan enige vertraging optreden.
LET OP
! Pioneer garandeert geen compatibiliteit met
alle USB-opslagapparaten en kan niet verant-
woordelijk worden gesteld voor eventueel ge-
gevensverlies op mediaspelers, smartphones
of andere apparaten tijdens gebruik van dit
product.
! Laat discs en USB -opslagapparaten niet ach-
ter op plaatsen waar de temperatuur hoog
kan oplopen.
Compatibiliteit met iPod
Alleen de volgende iPods kunnen met dit toestel
gebruikt worden.
Gemaakt voor
! iPod touch (5e generatie)
! iPod touch (4e generatie)
! iPod touch (3e generatie)
! iPod touch (2e generatie)
! iPod touch (1e generatie)
! iPod classic
! iPod met video
! iPod nano (7e generatie)
! iPod nano (6e generatie)
! iPod nano (5e generatie)
! iPod nano (4e generatie)
! iPod nano (3e generatie)
! iPod nano (2e generatie)
! iPod nano (1e generatie)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
Afhankelijk van de generatie en de versie van de
iPod zijn sommige functies mogelijk niet beschik-
baar.
De bediening kan variëren, afhankelijk van de soft-
wareversie van de iPod.
Gebruikers van een iPod met Lightning-aansluiting
moeten de Lightning-naar-USB-kabel gebruiken
(bij de iPod geleverd).
Gebruikers van een iPod met dock-connector moe-
ten CD-IU51 gebruiken. Raadpleeg uw leverancier
voor meer informatie.
Raadpleeg de handleiding van de iPod voor meer
informatie over ondersteunde bestandsindelingen.
Audioboek, podcast: Compatibel
LET OP
Pioneer is niet verantwoordelijk voor verlies van
gegevens op de iPod, ook niet tijdens gebruik
van dit toestel.
Volgorde van audiobestanden
De gebruiker kan met dit toestel geen mapnum-
mers toewijzen of de afspeelvolgorde wijzigen.
Nederlands
Aanvullende informatie
101
Aanhangsel
Aanvullende informatie
Nl
Black plate (102,1)
Voorbeeld van een boomstructuur
1
2
3
4
5
6
01
02
03
04
05
Niveau 1 Niveau 2 Niveau 3 Niveau 4
: Map
: Gecomprimeerd
audiobestand
01 tot 05: Mapnum-
mer
1 tot 6: Afspeel-
volgorde
Disc
De mapvolgorde en andere instellingen zijn af-
hankelijk van de software die voor het coderen
en schrijven is gebruikt.
USB-opslagapparaat
De afspeelvolgorde is gelijk aan de volgorde
waarin de bestanden zijn opgenomen op het
USB-opslagapparaat.
Ga als volgt te werk als u wilt dat bestanden in
een bepaalde volgorde worden afgespeeld.
1 Geef de bestanden namen met nummers die
de afspeelvolgorde aangeven, bijvoorbeeld
001xxx.mp3 en 099yyy.mp3.
2 Plaats de bestanden in een map.
3 Sla de map met bestanden op het USB-op-
slagapparaat op.
Merk echter op dat de afspeelvolgorde niet altijd
kan worden bepaald. Dit is afhankelijk van het
gebruikte systeem.
De afspeelvolgorde op draagbare USB-audiospe-
lers is verschillend en hangt af van de gebruikte
audiospeler.
Lijst van Russische tekens
S: T S: T S: T S: T S: T
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
S: T S: T S: T S: T S: T
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
S: Scherm T: Teken
Copyright en handelsmerken
MP3
Dit product is uitsluitend bedoeld voor niet-com-
mercieel privégebruik. Het mag niet in een com-
merciële omgeving worden gebruikt voor
realtime-uitzendingen (over land, via satelliet,
kabel en/of andere media), voor uitzendingen/
streaming via internet, intranet en/of andere net-
werken, of in andere elektronische distributie-
systemen zoals betaalradio of audio-op-
aanvraagtoepassingen. Hiervoor is een aparte li-
centie nodig. Kijk voor meer informatie op
http://www.mp3licensing.com.
WMA
Windows Media is een gedeponeerd handels-
merk of een handelsmerk van Microsoft
Corporation in de Verenigde Staten en/of in an-
dere landen.
Dit product bevat technologie die het eigendom
is van Microsoft Corporation en die niet gebruikt
of gedistribueerd mag worden zonder toestem-
ming van Microsoft Licensing, Inc.
iPod & iPhone
iPhone, iPod, iPod classic, iPod nano en iPod
touch zijn handelsmerken van Apple Inc., gede-
poneerd in de VS en andere landen.
Lightning is een handelsmerk van Apple Inc.
Gemaakt voor iPod en Gemaakt voor iPhone
wil zeggen dat een elektronische accessoire spe-
ciaal ontwikkeld is voor verbinding met respec-
tievelijk een iPod of iPhone en door de maker
gewaarborgd is als conform de Apple werkings-
normen. Apple is niet verantwoordelijk voor de
werking van dit apparaat en voor het voldoen
aan de veiligheidsnormen en wettelijke normen.
Houd er rekening mee dat het gebruik van dit
accessoire met iPod of iPhone invloed kan heb-
ben op de draadloze prestatie.
Androidä
Android is een handelsmerk van Google Inc.
Aanvullende informatie
102
Aanhangsel
Aanvullende informatie
Nl
Black plate (103,1)
Technische gegevens
Algemeen
Spanningsbron ................ 14,4 V gelijkstroom (10,8 tot
15,1 V toelaatbaar)
Aarding ........................... Negatief
Maximaal stroomverbruik
................................... 10,0 A
Afmetingen (B × H × D):
DIN
Chassis ............................ 178mm × 100mm × 157 mm
Voorkant .......................... 188mm × 118 mm × 25mm
D
Chassis ............................ 178mm × 100mm × 165 mm
Voorkant .......................... 170mm × 96mm × 17mm
Gewicht ........................... 1,2 kg
Audio
Maximaal uitgangsvermogen
................................... 50 W × 4
70 W × 1/2 W (voor de sub-
woofer)
Doorlopend uitgangsvermogen
................................... 22W × 4 (50Hz tot 15000Hz,
5% THD, 4 W belasting, beide
kanalen)
Belastingsimpedantie ...... 4 W (4 W tot 8 W toegestaan)
Preout maximaal uitgangsniveau
................................... 2,0V
Contouren loudness ......... +10dB (100 Hz), +6,5 dB
(10 kHz) (volume: 30 dB)
Equalizer (grafische equalizer met vijf banden):
Frequentie ....................... 80Hz/250 Hz/800 Hz/2,5 kHz/
8 kHz
Bereik equalizer ............... ±12 dB (in stappen van 2 dB)
Subwoofer (mono):
Frequentie ....................... 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Helling ............................. 12 dB/oct, 24 dB/oct
Gain ................................ +6dB tot 24 dB
Fase ................................. Normaal/tegengesteld
Cd-speler
Systeem ........................... Compact Disc Audio
Bruikbare discs ................ Compact Discs
Signaal-tot-ruisverhouding
................................... 94dB (1kHz) (IEC-A-netwerk)
Aantal kanalen ................. 2 (stereo)
MP3-decoderingsformaat
................................... MPEG-1 & 2 Audio Layer 3
WMA-decoderingsformaat
................................... Versie 7, 7.1, 8, 9, 10, 11, 12
(2 kan. audio)
(Windows Media Player)
WAV-signaalformaat ........ Lineaire PCM & MS ADPCM
(niet gecomprimeerd)
USB
USB-specificatie .............. USB 2.0 volledige snelheid
Maximaal stroomverbruik
................................... 1 A
USB-klasse ...................... MSC-apparatuur (Mass Sto-
rage Class)
Bestandssysteem ............. FAT12, FAT16, FAT32
MP3-decoderingsformaat
................................... MPEG-1 & 2 Audio Layer 3
WMA-decoderingsformaat
................................... Versie 7, 7.1, 8, 9, 10, 11, 12
(2 kan. audio)
(Windows Media Player)
WAV-signaalformaat ........ Lineaire PCM & MS ADPCM
(niet gecomprimeerd)
FM-tuner
Frequentiebereik .............. 87,5 MHz tot 108,0 MHz
Bruikbare gevoeligheid .... 9dBf (0,8 µV/75 W, mono, S/R:
30 dB)
Signaal-tot-ruisverhouding
................................... 72dB (IEC-A-netwerk)
MW-tuner
Frequentiebereik .............. 531 kHz tot 1 602kHz
Bruikbare gevoeligheid .... 25µV (S/R: 20 dB)
Signaal-tot-ruisverhouding
................................... 62dB (IEC-A-netwerk)
LW-tuner
Frequentiebereik .............. 153 kHz tot 281kHz
Bruikbare gevoeligheid .... 28µV (S/R: 20 dB)
Signaal-tot-ruisverhouding
................................... 62dB (IEC-A-netwerk)
Opmerking
Technische gegevens en ontwerp kunnen zonder
voorafgaande kennisgeving worden gewijzigd.
Nederlands
Aanvullende informatie
103
Aanhangsel
Nl
Black plate (104,1)
Благодарим Вас
за покупку этого изделия
компании PIONEER
Для обеспечения правильности эксплуата-
ции внимательно прочитайте данное руко-
водство перед началом использования
изделия. Особенно важно, чтобы Вы прочли
и соблюдали инструкции, помеченные в дан-
ном руководстве заголовками ПРЕДУПРЕ-
ЖДЕНИЕ и ВНИМАНИЕ.
Держите данное
руководство под рукой для обращения к
нему в будущем.
Если вы желаете утилизировать данное
изделие, не выбрасывайте его вместе с
обычным бытовым мусором. Существует
отдельная система сбора использованных
электронных изделий в соответствии с за-
конодательством, которая предполагает
соответствующее обращение, возврат и
переработку.
Частные лица в странах Евросоюза, Швей-
царии и Норвегии могут бесплатно возвра-
щать использованные электронные изделия
в специализированные пункты приема или в
магазин (при покупке аналогичного нового
устройства).
Если Ваша страна не указана в приведенном
выше перечне, обращайтесь в органы мест-
ного управления за инструкциями по пра-
вильной утилизации продукта.
Тем самым Вы обеспечите утилизацию Ва-
шего изделия с соблюдением обязательных
процедур по обработке, утилизации и вто-
ричной переработке и, таким образом, пред-
отвратите потенциальное негативное
воздействие на окружающую среду и здоро-
вье людей.
Дату изготовления оборудования можно
определить по серийному номеру, который
содержит информацию о месяце и годе про-
изводства.
Сведения об этом устройстве
Частоты тюнера в этом устройстве распре-
делены для использования в Западной
Европе, Азии, на Ближнем Востоке, в Афри-
ке и Океании. При использовании в других
регионах качество приема может быть пло-
хим. Функция RDS (радиовещательная си-
стема передачи информации) работает
только в регионах, где транслируются сигна-
лы RDS для FM-станций.
ПРЕДУПРЕЖДЕНИЕ
! Не пытайтесь самостоятельно произ-
водить установку или ремонт изделия.
Установка или ремонт изделия лица-
ми, не обладающими специальными
навыками и опытом работы с элек-
тронным оборудованием и автомо-
бильными аксессуарами, могут
создать опасность поражения электри-
ческим током или иных инцидентов.
! Ни в коем случае не пытайтесь управлять
устройством во время движения. Прежде
чем использовать органы управления ус-
тройством, необходимо съехать с дороги
и припарковать автомобиль в безопасном
месте.
ВНИМАНИЕ
! Не допускайте попадания жидкости на ус-
тройство. Это может повлечь поражение
электрическим током. Кроме того, попада-
ние жидкости в устройство может стать
причиной его выхода из строя, перегрева
и появления дыма.
! Pioneer CarStereo-Pass предназначен для
использования только в Германии.
! Всегда сохраняйте уровень громкости до-
статочно низким, чтобы были слышны
звуки извне.
! Не допускайте воздействия влажности на
изделие.
ВНИМАНИЕ
Данное изделие является лазерным изде-
лием класса 1 согласно классификации по
Безопасности лазерных изделий, IEC
60825-1:2007.
ЛАЗЕРНЫЙ ПРОДУКТ КЛАСС 1
При возникновении проблем
При неполадках в работе этого изделия свя-
житесь с торговым представителем компа-
нии-производителя или с ближайшим
сервисным пунктом PIONEER.
Перед началом эксплуатации
104
Раздел
Перед началом эксплуатации
Ru
01
Black plate (105,1)
Основное устройство
1 2 4 5
8 9
7 a c6 b d
3
1 h (извлечение)
2 iPod
3 С 1/
по 6/
4 Щель для загрузки диска
5 DISP
6 SRC/OFF
7 BAND/
(управление iPod)
8 c/d
9 MULTI-CONTROL (M.C.)
a
(назад)/DIMMER (регулятор освещен-
ности)
b
(список)
c Вход AUX (стереоразъем 3,5 мм)
d USB порт
ВНИМАНИЕ
Для подключения запоминающих устройств
USB используйте USB-кабель Pioneer (CD-
U50E, приобретается отдельно), поскольку
любое устройство при подключении напря-
мую выступает из устройства, что создает
потенциальную опасность.
Индикация на дисплее
31 4 86
a
2 5 7 9
b
1 (список)
2
(управление iPod)
Управление функциями iPod производит-
ся с устройства iPod.
3 Сектор дополнительной информации
4 TA (дорожные сводки)
5 TP (идентификатор дорожных программ)
6
(sound retriever, технология пре-
образования звука)
7 LOC (настройка с местным поиском)
8
(повтор)
9
(в произвольной последовательно-
сти)
a
Сектор основной информации
! Тюнер: диапазон и частота
! RDS: название программы, PTY-ин-
формация и прочая текстовая инфор-
мация
! Проигрыватель компакт-дисков, запо-
минающее устройство USB и iPod:
время, прошедшее с начала вос-
произведения, и текстовая информа-
ция
b
Отображается при наличии нижнего
уровня папки или меню.
Установочное меню
1 После установки устройства поверни-
те ключ зажигания в положение ON.
Появится надпись SET UP.
2 Поверните M.C. для выбора YES.
# Если в течение 30 секунд устройство не ис-
пользуется, установочное меню не будет выво-
диться.
# Если вы хотите выполнить настройку позже,
поверните M.C., чтобы выбрать NO.
3 Нажмите M.C. для выбора.
4 Настройте меню с помощью описан-
ных ниже действий.
Для перехода к следующему пункту меню
необходимо подтвердить выбор.
LANGUAGE (выбор языка)
Данное устройство может отображать тексто-
вую информацию из сжатых аудиофайлов, в
том числе информацию на английском, рус-
ском и турецком языках.
! При несовместимости настроек встроенно-
го и выбранного языка возможны искаже-
ния при выводе текстовых сообщений.
! Некоторые символы могут отображаться
неправильно.
1 Поворачивайте M.C. для выбора настрой-
ки.
ENG (английский)РУС (русский)TUR (ту-
рецкий)
2 Нажмите M.C., чтобы подтвердить выбор.
CLOCK SET (установка часов)
1 Поворачивайте M.C., чтобы установить
часы.
2 Нажимайте M.C., чтобы выбрать установку
минут.
3 Поворачивайте M.C., чтобы установить ми-
нуты.
4 Нажмите M.C., чтобы подтвердить выбор.
FM STEP (шаг настройки в FM-диапазоне)
Для установки шага настройки в FM-диапазоне
(настройки поиска) используйте меню FM
STEP.
1 Поверните M.C., чтобы выбрать шаг на-
стройки в FM-диапазоне.
100 (100 кГц)50 (50 кГц)
2 Нажмите M.C., чтобы подтвердить выбор.
Появится надпись QUIT.
! Шаг ручной настройки фиксированный и
составляет 50 кГц.
! При выключении функций AF и TA шаг на-
стройки автоматически меняется на 50 кГц,
даже если установлено 100.
Русский
Использование данного устройства
105
Раздел
Использование данного устройства
Ru
02
Black plate (106,1)
5 Чтобы закончить настройку, поверни-
те M.C. и выберите YES.
# Если понадобится вновь изменить настройку,
поверните M.C. и выберите NO.
6 Нажмите M.C. для выбора.
Примечания
! Настроить параметры меню можно в
меню системы и в начальном меню.
Более подробную информацию см. в раз-
делах
Меню системы
на стр.112и
Стар-
товое меню
на стр. 113.
! Вы можете отменить настройку парамет-
ра, нажав кнопку SRC/OFF.
Основные операции
Включение устройства
1 Нажмите кнопку SRC/OFF, чтобы включить
устройство.
Выключение устройства
1 Нажмите и удерживайте кнопку SRC/OFF,
пока устройство не выключится.
Выбор источника сигнала
1 Нажимайте кнопку SRC/OFF для выбора из
следующих функций:
RADIOCDUSB/iPodAPP (приложение)
AUX
! При подключении по протоколу MTP на
дисплее отображается USB MTP.
! Если подключен iPod и выбран любой ис-
точник сигнала, кроме iPod, можно пере-
ключиться на iPod с помощью кнопки iPod.
Регулировка громкости
1 Для регулировки громкости поворачивайте
M.C.
Примечание
Когда голубой/белый провод этого устрой-
ства подключен к реле панели управления
автомобильной антенной, антенна на авто-
мобиле выдвигается при включении источни-
ка сигнала этого устройства. Чтобы втянуть
антенну, выключите источник сигнала.
Часто используемые
элементы меню
Возврат к предыдущему дисплею
Возврат к предыдущему списку (к папке на
один уровень выше)
1 Нажмите кнопку
/DIMMER.
Возврат в исходный режим
Выход из главного меню
1 Нажмите кнопку BAND/
.
Возврат в исходный режим из списка
1 Нажмите кнопку BAND/
.
Радиоприемник
Основные операции
Выбор диапазона
1 Нажимайте кнопку BAND/
, пока на дис-
плее не отобразится нужный диапазон
(FM1, FM2, FM3 для FM или MW/LW).
Переключение станций предварительной на-
стройки
1 Нажмите кнопку c или d.
! Чтобы использовать эту функцию, в меню
SEEK выберите PCH (запрограммированная
станция).
Ручная настройка (пошаговая)
1 Нажмите кнопку c или d.
! Чтобы использовать эту функцию, в меню
SEEK выберите MAN (ручная настройка).
Поиск
1 Нажмите и удерживайте кнопку c или d, а
затем отпустите.
Вы можете отменить настройку с поиском
кратким нажатием c или d.
При нажатии и удерживании кнопки c или
d можно пропускать радиостанции. На-
стройка с поиском начнется сразу после от-
пускания кнопки c или d.
Примечания
! Подробную информацию о меню SEEK
см. в разделе
SEEK (настройка левой и
правой кнопок)
на стр. 107.
! Можно включить или выключить функцию
AF (поиск альтернативных частот) данно-
го устройства. Для обычной настройки
функция AF должна быть выключена
(смотрите в
AF (поиск альтернативных ча-
стот)
на стр. 107).
Сохранение и вызов из памяти
радиостанций для каждого
диапазона
Использование кнопок
предварительной настройки
1 Сохранение: нажмите и удерживайте
одну из кнопок предварительной на-
стройки (с 1/
по 6/ ), пока номер не
прекратит мигать.
2 Вызов: нажмите одну из кнопок пред-
варительной настройки (с 1/
по 6/ ).
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! FREQUENCY (служебное название про-
граммы или частота)
! BRDCST INFO (служебное название про-
граммы/информация PTY)
! CLOCK (название источника сигнала и
часы)
Примечания
! Если служебное название программы в
поле FREQUENCY отсутствует, вместо
него отображается канал. Если служеб-
ное название программы обнаружено,
оно будет отображаться.
! Текстовая информация может меняться в
зависимости от диапазона.
! Возможность внесения изменений в тек-
стовую информацию зависит от региона.
Использование функций PTY
Можно настроиться на радиостанцию с по-
мощью информации PTY (типа программы).
Использование данного устройства
106
Раздел
Использование данного устройства
Ru
02
Black plate (107,1)
Поиск станции RDS с помощью информации
PTY
1 Нажмите
(список).
2 Кнопкой M.C. выберите тип программы.
NEWS/INFOPOPULARCLASSICSOT-
HERS
3 Нажмите M.C., чтобы начать поиск.
Устройство начинает поиск радиостанций,
передающих данный тип программ. При
обнаружении радиостанции на дисплее
будет показано название данной програм-
мы.
! Для отмены поиска нажмите M.C. еще
раз.
! Программы некоторых радиостанций
могут отличаться от программ, указан-
ных в передаваемом коде PTY.
! Если ни одна из станций не передает
программы нужного типа, то на дисплее
в течение примерно двух секунд будет
показано NOT FOUND, и затем тюнер
перейдет в режим приема станции, ско-
торой был начат поиск.
Список PTY
Более подробную информацию о списке
PTY можно получить на веб-сайте:
http://www.pioneer.eu/eur/products/25/121/tech/
CarAudio/PTY.html
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
3 Для выбора функции поворачивайте
M.C.
Следующие выбранные функции можно на-
страивать.
# В диапазонах MW/LW можно выбрать только
BSM, LOCAL и SEEK.
FM SETTING (настройки качества звука FM)
Уровень качества звука можно установить в
соответствии с условиями приема сигнала в
FM-диапазоне.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора настрой-
ки.
! STANDARD стандартная настройка.
! HI-FI настройка с приоритетом высоко-
го качества стереозвучания.
! STABLE настройка с приоритетом низ-
кого уровня помех монофонического
звучания.
BSM (запоминание лучших станций)
Функция BSM (запоминание лучших станций)
позволяет автоматически сохранять в памяти
устройства шесть станций с самым мощным
сигналом в порядке убывания его мощности.
1 Нажмите M.C., чтобы включить функцию
BSM.
Для отмены режима нажмите M.C. еще раз.
REGIONAL (региональный)
При использовании функции AF функция ре-
гиональных программ ограничивает выбор
станциями, транслирующими региональные
программы.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию региональных программ.
LOCAL (настройка с местным поиском)
Настройка с местным поиском позволяет Вам
настраиваться только на радиостанции с до-
статочно мощными сигналами для качествен-
ного приема.
1 Нажмите M.C. для выбора нужной настрой-
ки.
FM: OFFLV1LV2LV3LV4
MW/LW: OFFLV1LV2
Настройка самого высокого уровня позво-
ляет осуществлять прием только станций с
самым сильным сигналом, а уменьшение
уровня настройки позволяет принимать
станции с более слабым сигналом.
TA (режим ожидания дорожных сводок)
1 Нажмите M.C., чтобы включить или выклю-
чить режим ожидания дорожных сводок.
AF (поиск альтернативных частот)
1 Нажмите M.C., чтобы включить или выклю-
чить функцию AF.
NEWS (прерывание для передачи новостей)
1 Нажмите M.C., чтобы включить или выклю-
чить функцию НОВОСТИ.
SEEK (настройка левой и правой кнопок)
Правой и левой кнопкам на устройстве можно
назначить определенную функцию.
Выберите MAN (ручная настройка) для ручной
настройки или PCH (предустановленный
канал) для переключения между заранее на-
строенными каналами.
1 Нажмите кнопку M.C., чтобы выбрать MAN
или PCH.
CD/CD-R/CD-RW и
запоминающие устройства
USB
Подключение по протоколу MTP
Устройства Android, поддерживающие прото-
кол MTP (с операционной системой Android
OS 4.0 или выше), можно подключить по про-
токолу MTP как USB-устройство. Для под-
ключения используйте кабель, входящий в
комплект поставки устройства Android.
Примечание
Эта функция не поддерживает WAV.
Основные операции
Воспроизведение CD/CD-R/CD-RW
1 Вставьте диск в щель для загрузки марки-
рованной стороной вверх.
Извлечение диска CD/CD-R/CD-RW
1 Нажмите h.
Воспроизведение композиций на запоминаю-
щем устройстве USB
1 Откройте крышку порта USB.
2 Подключите запоминающее устройство
USB с помощью кабеля USB.
Остановка воспроизведения файлов на запо-
минающем устройстве USB
1 Запоминающее устройство USB можно от-
ключить в любой момент.
Выбор папки
1 Нажмите кнопку 1/
или 2/ .
Выбор дорожки
1 Нажмите кнопку c или d.
Русский
Использование данного устройства
107
Раздел
Использование данного устройства
Ru
02
Black plate (108,1)
Ускоренная перемотка вперед или назад
1 Нажмите и удерживайте кнопку c или d.
! При воспроизведении сжатых аудиофай-
лов звук не воспроизводится, если включе-
на ускоренная перемотка вперед или
назад.
Возврат к корневой папке
1 Нажмите и удерживайте кнопку BAND/
.
Переключение между сжатыми аудиофайлами
и диском CD-DA
1 Нажмите кнопку BAND/
.
Переключение между запоминающими ус-
тройствами
При наличии нескольких запоминающих ус-
тройств USB Mass Storage воспроизведение
можно переключать между ними.
1 Нажмите кнопку BAND/
.
! Возможно переключение между 32 различ-
ными запоминающими устройствами.
Примечание
Если запоминающее устройство USB не ис-
пользуется, отключите его.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
CD-DA
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
CD-TEXT
! TRACK INFO (название дорожки/испол-
нитель/название диска)
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
MP3/WMA/WAV
! TRACK INFO (название дорожки/имя ис-
полнителя/название альбома)
! FILE INFO (название папки/название
файла)
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
Выбор и воспроизведение
фалов/дорожек из списка
1 Нажмите кнопку , чтобы отобразить
список названий файлов/дорожек.
2 С помощью M.C. выберите нужное
имя файла (или папки).
Выбор файла или папки
1 Поворачивайте M.C.
Воспроизведение
1 Выберите файл или дорожку и нажмите M.
C.
Просмотр списка названий файлов (папок) в
выбранной папке
1 Выберите папку и нажмите M.C.
Воспроизведение композиции из выбранной
папки
1 Выберите папку, затем нажмите и удержи-
вайте M.C.
Функции с использованием
специальных кнопок
Выбор диапазона повторного воспроизведе-
ния
1 Нажимайте кнопку 6/
для выбора из сле-
дующих функций:
CD/CD-R/CD-RW
! ALL Повторное воспроизведение всех
дорожек
! ONE Повтор текущей дорожки
! FLD Повтор текущей папки
Запоминающее устройство USB
! ALL Повтор всех файлов
! ONE Повтор текущего файла
! FLD Повтор текущей папки
Воспроизведение дорожек в произвольной по-
следовательности
1 Нажмите кнопку 5/
, чтобы включить или
выключить функцию воспроизведения в
произвольной последовательности.
Данная функция позволяет воспроизводить
дорожки в произвольной последовательно-
сти в пределах выбранного диапазона по-
вторного воспроизведения.
! Для переключения на следующую дорожку
во время воспроизведения в произвольной
последовательности нажмите кнопку d.
При нажатии на кнопку c воспроизведение
текущей дорожки начинается с начала.
Приостановка воспроизведения
1 Нажмите кнопку 4/PAUSE, чтобы включить
паузу или возобновить воспроизведение.
Улучшение качества звука сжатых аудиофай-
лов и восстановление полноты звучания (тех-
нология преобразования звука)
1 Нажимайте кнопку 3/S.Rtrv для выбора из
следующих функций:
12OFF (выкл)
Настройка 1 эффективна для файлов с
низкой степенью сжатия, а настройка 2
для файлов с высокой степенью сжатия.
Использование данного устройства
108
Раздел
Использование данного устройства
Ru
02
Black plate (109,1)
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
Выбранные функции, которые можно на-
страивать, перечислены ниже.
S.RTRV (sound retriever, технология преобраз-
ования звука)
Автоматически улучшает качество звука сжа-
тых аудиофайлов и восстанавливает полноту
звучания.
1 Нажмите M.C. для выбора нужной настрой-
ки.
Подробную информацию см. в
Улучшение
качества звука сжатых аудиофайлов и вос-
становление полноты звучания (технология
преобразования звука)
на стр. 108.
iPod
Основные операции
Воспроизведение музыки на iPod
1 Откройте крышку порта USB.
2 Подключите iPod к разъему USB.
Воспроизведение начинается автоматиче-
ски.
Выбор композиции (раздела)
1 Нажмите кнопку c или d.
Выбор альбома
1 Нажмите кнопку 1/
или 2/ .
Ускоренная перемотка вперед или назад
1 Нажмите и удерживайте кнопку c или d.
Примечания
! iPod можно включить или выключить,
если выбран режим управления
CTRL AUDIO.
! Перед подключением iPod к данному ус-
тройству отсоедините от него наушники.
! Выключение iPod происходит примерно
через две минуты после выключения за-
жигания.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! TRACK INFO (название дорожки/имя ис-
полнителя/название альбома)
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
Поиск композиции
1 Для перехода к главному меню поиска
по списку нажмите
.
2 С помощью M.C. выберите категорию/
композицию.
Выбор названия композиции или категории
1 Поворачивайте M.C.
Плейлистыисполнителиальбомы-
композицииподкастыжанрыкомпози-
торыаудиокниги
Воспроизведение
1 Выберите композицию и нажмите M.C.
Просмотр списка композиций в выбранной ка-
тегории
1 Выберите категорию и нажмите M.C.
Воспроизведение композиции в выбранной ка-
тегории
1 Выберите категорию, затем нажмите и
удерживайте M.C.
Поиск в списке по алфавиту
1 Когда список выбранной категории отобра-
зится на дисплее, нажмите
, чтобы вклю-
чить режим поиска по алфавиту.
! Дважды повернув M.C., можно перейти
в режим поиска по алфавиту.
2 Для выбора буквы поворачивайте M.C.
3 Нажмите M.C. для отображения списка по
алфавиту.
! Для отмены поиска нажмите
/DIMMER.
Примечания
! Можно воспроизводить списки воспроиз-
ведения, созданные с помощью приложе-
ния для компьютера (MusicSphere).
Приложение можно скачать на нашем
сайте.
! Списки воспроизведения, созданные с по-
мощью приложения (MusicSphere), будут
отображаться в сокращенном виде.
Функции с использованием
специальных кнопок
Выбор диапазона повторного воспроизведе-
ния
1 Нажимайте кнопку 6/
для выбора из сле-
дующих функций:
! ONE повтор текущей композиции
! ALL повтор всех композиций в вы-
бранном списке
! Если выбран режим управления CTRL iPod,
диапазон повторного воспроизведения
будет аналогичным установленному для
подключенного iPod.
Выбор диапазона воспроизведения в произ-
вольной последовательности (перемешать)
1 Нажимайте кнопку 5/
для выбора из
следующих функций:
! SNG воспроизведение композиций из
выбранного списка в произвольной по-
следовательности.
! ALB воспроизведение по порядку ком-
позиций из альбома, выбранного слу-
чайным образом.
! OFF отмена воспроизведения в произ-
вольной последовательности.
Воспроизведение всех композиций в произ-
вольной последовательности (перемешать
все)
1 Нажмите и удерживайте кнопку
/5,
чтобы включить функцию перемешать
все.
! Чтобы отключить функцию перемешать
все, выберите OFF в меню перемешива-
ния. Подробнее см. в разделе
Выбор диа-
пазона воспроизведения в произвольной
последовательности (перемешать)
на
стр. 109.
Русский
Использование данного устройства
109
Раздел
Использование данного устройства
Ru
02
Black plate (110,1)
Приостановка воспроизведения
1 Нажмите кнопку 4/PAUSE, чтобы включить
паузу или возобновить воспроизведение.
Улучшение качества звука сжатых аудиофай-
лов и восстановление полноты звучания (тех-
нология преобразования звука)
1 Нажимайте кнопку 3/S.Rtrv для выбора из
следующих функций:
12OFF (выкл)
Настройка 1 эффективна для файлов с
низкой степенью сжатия, а настройка 2
для файлов с высокой степенью сжатия.
Воспроизведение композиций в
жанре воспроизводимой в
данный момент композиции
Можно воспроизводить композиции из сле-
дующих списков.
Список альбомов артиста, композиция ко-
торого воспроизводится в данный момент
Список композиций, относящихся к вос-
производимому в данный момент альбому
Список альбомов, относящихся к воспроиз-
водимому в данный момент музыкальному
жанру
1 Нажмите и удерживайте кнопку
для
переключения в режим воспроизведения
по категории.
2 Для изменения режима вращайте M.C.,
для выбора нажмите.
! ARTIST Воспроизведение альбома арти-
ста, композиция которого воспроизводит-
ся в данный момент.
! ALBUM Воспроизведение композиции
из альбома, который воспроизводится в
данный момент.
! GENRE Воспроизведение альбома в
жанре, который воспроизводится в дан-
ный момент.
Выбранная композиция или альбом будет
воспроизводиться после окончания вос-
произведения текущей композиции.
Примечания
! Возможна отмена воспроизведения вы-
бранной композиции/альбома, если вы
используете любые другие функции,
кроме поиска по категории (например, пе-
ремотка вперед или назад).
! В зависимости от того, какая композиция
выбрана, конец текущей композиции и на-
чало выбранной композиции/альбома
могут быть обрезаны.
Использование функций iPod
данного устройства на вашем iPod
Управление функциями iPod данного устрой-
ства может производиться с подключенного
iPod.
Режим CTRL iPod несовместим со следующи-
ми моделями iPod:
! iPod nano 1-го поколения
! iPod с поддержкой видео
% Переключение между режимами упра-
вления производится нажатием BAND/
.
! CTRL iPod управление функциями iPod
данного устройства может производиться
с подключенного iPod.
! CTRL AUDIO управление функциями
iPod данного устройства может произво-
диться с помощью органов управления
данного устройства.
Переключение режима управления также
производится нажатием кнопки iPod.
Примечания
! При переключении на режим управления
CTRL iPod воспроизведение композиции
приостанавливается. Чтобы возобновить
воспроизведение, используйте iPod.
! Следующими функциями можно упра-
влять с данного устройства, даже если
выбран режим управления CTRL iPod.
Пауза
Ускоренная перемотка вперед/назад
Выбор композиции (раздела)
! Громкость можно регулировать только с
основного устройства.
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
3 Для выбора функции поворачивайте
M.C.
Следующие выбранные функции можно на-
страивать.
! Функция AUDIO BOOK недоступна, если в
качестве режима воспроизведения выбра-
но CTRL iPod. Подробнее см. в разделе
Использование функций iPod данного ус-
тройства на вашем iPod
на стр. 110.
AUDIO BOOK (скорость воспроизведения ау-
диокниги)
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C., чтобы выбрать нуж-
ную настройку.
! FASTER Ускоренное воспроизведение
! NORMAL Воспроизведение с обычной
скоростью
! SLOWER Замедленное воспроизведе-
ние
S.RTRV (sound retriever, технология преобраз-
ования звука)
1 Нажмите M.C. для выбора нужной настрой-
ки.
Подробную информацию см. в
Улучшение
качества звука сжатых аудиофайлов и вос-
становление полноты звучания (технология
преобразования звука)
на стр. 110.
Использование приложений
на подсоединенном устройстве
Это устройство можно использовать для по-
токового воспроизведения и управления
композициями на iPhone с помощью прило-
жений или только для потокового воспроиз-
ведения.
Использование данного устройства
110
Раздел
Использование данного устройства
Ru
02
Black plate (111,1)
Важно
Использование приложений сторонних
разработчиков может включать в себя или
требовать предоставления личных данных
(создание профиля пользователя или дру-
гие способы), а для некоторых приложе-
ний - предоставления данных о
местонахождении.
ВСЕ ПРИЛОЖЕНИЯ СТОРОННИХ РАЗРА-
БОТЧИКОВ НАХОДЯТСЯ В СФЕРЕ ОТ-
ВЕТСТВЕННОСТИ ЭТИХ
РАЗРАБОТЧИКОВ, ЧТО БЕЗ ОГРАНИЧЕ-
НИЙ ВКЛЮЧАЕТ В СЕБЯ СБОР И БЕЗ-
ОПАСНОСТЬ ПОЛЬЗОВАТЕЛЬСКИХ
ДАННЫХ И ОБРАЩЕНИЕ С ЧАСТНОЙ
ИНФОРМАЦИЕЙ. ПРИ ИСПОЛЬЗОВАНИИ
ПРИЛОЖЕНИЙ СТОРОННИХ РАЗРАБОТ-
ЧИКОВ ВЫ СОГЛАШАЕТЕСЬ С УСЛО-
ВИЯМИ ПРЕДОСТАВЛЕНИЯ СЕРВИСА И
ПОЛИТИКОЙ КОНФИДЕНЦИАЛЬНОСТИ
РАЗРАБОТЧИКОВ. ЕСЛИ ВЫ НЕ СОГЛАС-
НЫ С УСЛОВИЯМИ ИЛИ ПОЛИТИКОЙ
РАЗРАБОТЧИКА ИЛИ НЕ ЖЕЛАЕТЕ
ПРЕДОСТАВЛЯТЬ ДАННЫЕ О СВОЕМ
МЕСТОНАХОЖДЕНИИ, КОГДА ЭТО ТРЕ-
БУЕТСЯ, НЕ ИСПОЛЬЗУЙТЕ ТАКОЕ ПРИ-
ЛОЖЕНИЕ.
Сведения о совместимости
подключаемых устройств
Ниже приводится подробная информация о
разъемах, необходимых для использования
приложений с iPhone на этом устройстве.
Для пользователей iPhone
! Данная функция поддерживается iPhone
и iPod touch.
! На устройстве установлена iOS 5.0 или
более поздней версии.
Примечания
! Список совместимых приложений для
iPhone см. на нашем сайте.
! Компания Pioneer не несет ответственно-
сти за любые проблемы, связанные с не-
корректными или поврежденными
данными приложений.
! За содержимое и функциональность под-
держиваемых приложений несут ответ-
ственность разработчики приложений.
Порядок запуска для
пользователей iPhone
1 Подключите iPhone к разъему USB.
2 Переключите источник сигнала на
APP.
3 Запустите приложение на iPhone и
включите воспроизведение.
Основные операции
Выбор дорожки
1 Нажмите кнопку c или d.
Ускоренная перемотка вперед или назад
1 Нажмите и удерживайте кнопку c или d.
Приостановка воспроизведения
1 Нажмите кнопку BAND/
, чтобы включить
паузу или возобновить воспроизведение.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! TRACK INFO (название дорожки/имя ис-
полнителя/название альбома)
! APP NAME (название приложения)
! ELAPSED TIME (время воспроизведе-
ния)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
3 Для выбора функции поворачивайте
M.C.
Следующие выбранные функции можно на-
страивать.
PAUSE (пауза)
1 Нажмите M.C., чтобы включить паузу или
возобновить воспроизведение.
S.RTRV (sound retriever, технология преобраз-
ования звука)
1 Нажмите M.C. для выбора нужной настрой-
ки.
12OFF (выкл.)
Настройка 1 эффективна для файлов с
низкой степенью сжатия, а настройка 2
для файлов с высокой степенью сжатия.
Регулировки параметров звука
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
AUDIO.
3 Для выбора аудиофункции поворачи-
вайте M.C.
Следующие выбранные аудиофункции
можно настраивать.
! Функция FADER недоступна, если в режи-
ме SP-P/O MODE выбрано SUB.W/SUB.W.
Подробнее см. в разделе
SP-P/O MODE
(настройка выхода заднего канала и пред-
варительного усилителя)
на стр. 113.
! Функции SUB.W и SUB.W CTRL недоступ-
ны, если в режиме SP-P/O MODE выбрано
REAR/REAR. Подробнее см. в разделе
SP-P/O MODE (настройка выхода заднего
канала и предварительного усилителя)
на
стр. 113.
! Функция SUB.W CTRL недоступна, если в
режиме OFF выбрано SUB.W. Подробнее
см. в разделе
SUB.W (включение/выклю-
чение сабвуфера)
на стр. 112.
! Функция SLA недоступна, если в качестве
источника сигнала выбрано FM.
FADER (регулировка баланса)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажмите M.C., чтобы отрегулировать ба-
ланс передних и задних громкоговорите-
лей.
BALANCE (регулировка баланса)
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C., чтобы отрегулировать
баланс левого/правого громкоговорителей.
EQ SETTING (вызов настроек эквалайзера)
Русский
Использование данного устройства
111
Раздел
Использование данного устройства
Ru
02
Black plate (112,1)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажмите кнопку M.C., чтобы выбрать эква-
лайзер.
POWERFULNATURALVOCALCU-
STOM1CUSTOM2FLATSUPER BASS
Полосу и уровень эквалайзера можно отре-
гулировать, если выбрано CUSTOM1 или
CUSTOM2.
При выборе CUSTOM1 или CUSTOM2 вы-
полните действия, описанные ниже. При
выборе других настроек нажмите M.C.,
чтобы вернуться к предыдущему дисплею.
! CUSTOM1 можно выбрать отдельно для
каждого источника сигнала. Однако для
USB, iPod и APP автоматически устана-
вливаются одинаковые настройки.
! CUSTOM2 - это общая настройка, ис-
пользуемая для всех источников сигна-
ла.
3 Для отображения установочного меню на-
жмите M.C.
4 Нажимайте M.C. для выбора из следующих
функций:
Полоса эквалайзераУровень эквалайзе-
ра
5 Поворачивайте M.C. для выбора настрой-
ки.
Полоса эквалайзера: 80HZ250HZ
800HZ2.5KHZ8KHZ
Уровень эквалайзера: от +6 до 6
LOUDNESS (тонкомпенсация)
Тонкомпенсация компенсирует недостаточное
звуковое давление в нижнем и верхнем диапа-
зонах частот на низкой громкости.
1 Нажмите M.C. для выбора нужной настрой-
ки.
OFF (выкл)LOW (низкий)MID (средний)
HI (высокий)
SUB.W (включение/выключение сабвуфера)
Это устройство имеет выход канала сабвуфе-
ра, который можно включать и выключать.
1 Нажмите M.C. для выбора нужной настрой-
ки.
NOR (нормальная фаза)REV (обратная
фаза)OFF (сабвуфер выключен)
SUB.W CTRL (настройка сабвуфер)
На выходе сабвуфера будут воспроизводиться
только те частоты, которые ниже указанных ча-
стот среза.
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C. для выбора из следующих
функций:
Частота срезаУровень выходного сигна-
лаКрутизна характеристики
Изменяемые значения будут мигать.
3 Поворачивайте M.C. для выбора настрой-
ки.
Частота среза: 50HZ63HZ80HZ100HZ
125HZ160HZ200HZ
Уровень выходного сигнала: от 24 до +6
Крутизна характеристики: 12 24
BASS BOOST (усиление нижних звуковых ча-
стот)
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора нужного
уровня.
При увеличении или уменьшении уровня
отображаются надписи с 0 до +6.
HPF SETTING (настройка фильтра верхних ча-
стот)
Используйте эту функцию, если вы хотите,
чтобы воспроизводилисьтолько высокие ча-
стоты. На громкоговорители будут выводиться
только частоты выше, чем установленные
фильтром высоких частот (HPF).
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C. для выбора из следующих
функций:
Частота срезаКрутизна характеристики
3 Поворачивайте M.C. для выбора настрой-
ки.
Частота среза: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Крутизна характеристики: 12 24
SLA (регулировка уровня входного сигнала)
Эта функция предупреждает скачки громкости
при смене источника сигнала.
! Настройки основываются на уровне гром-
кости FM-тюнера, который остается неиз-
менным.
! Регулировку уровня громкости в диапазоне
MW/LW также можно производить с по-
мощью данной функции.
! Для USB, iPod и APP автоматически устана-
вливается одинаковая настройка.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивая M.C., отрегулируйте уровень
громкости источника сигнала.
Диапазон настройки: от +4 до 4
Меню системы
Важно
PW SAVE (режим энергосбережения) отклю-
чается при отсоединении аккумуляторной
батареи автомобиля; при подсоединении ба-
тареи его потребуется включить снова. При
выключенном режиме PW SAVE (режим
энергосбережения) возможно, что, в зависи-
мости от метода подключения, устройство
будет потреблять энергию аккумулятора,
если зажигание автомобиля не имеет поло-
жения АСС.
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
3 Для выбора функции меню системы
поворачивайте M.C.
Следующие выбранные функции меню си-
стемы можно настраивать.
LANGUAGE (выбор языка)
1 Нажмите M.C. для выбора нужной настрой-
ки.
ENG (английский)РУС (русский)TUR (ту-
рецкий)
CLOCK SET (установка часов)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C., чтобы выбрать сегмент
дисплея часов, который нужно установить.
ЧасыМинуты
3 Поворачивайте M.C., чтобы отрегулировать
время.
12H/24H (формат отображения времени)
1 Нажмите M.C. для выбора нужной настрой-
ки.
12H (12-часовой)24H (24-часовой)
AUTO PI (автоматический поиск по идентифи-
катору программы)
Устройство может автоматически искать дру-
гую станцию с такой же программой даже во
время вызова предварительной настройки.
1 Нажмите M.C., чтобы включить или выклю-
чить автоматический поиск по идентифика-
тору программы.
AUX (вспомогательный вход)
Использование данного устройства
112
Раздел
Использование данного устройства
Ru
02
Black plate (113,1)
Активируйте эту настройку при подключении к
данному устройству вспомогательного устрой-
ства.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию AUX.
DIMMER (регулятор освещенности)
1 Нажмите M.C., чтобы включить или выклю-
чить регулятор освещенности.
! Вы также можете выбрать другую настрой-
ку регулятора освещенности, удерживая
нажатой кнопку
/DIMMER.
MUTE MODE (режим приглушения звука)
Звук/уровень звукового сигнала данной систе-
мы автоматически понижается при получении
сигнала от оборудования с функцией приглу-
шения звука.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора настрой-
ки.
! MUTE приглушение звука
! 20dB ATT ослабление уровня сигнала
(20dB ATT имеет более сильный эф-
фект, чем 10dB ATT)
! 10dB ATT ослабление уровня сигнала
PW SAVE (энергосбережение)
Включение этой функции позволяет снизить
потребляемую мощность аккумуляторной ба-
тареи.
! При включении этой функции единствен-
ной возможной операцией является вклю-
чение источника сигнала.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию энергосбережения.
Стартовое меню
1 Нажмите и удерживайте кнопку SRC/
OFF, пока устройство не выключится.
2 Нажмите кнопку SRC/OFF и удерживай-
те ее, пока не откроется стартовое меню.
3 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
INITIAL.
4 Для выбора функции меню системы
поворачивайте M.C.
Следующие выбранные функции стартового
меню можно настраивать.
FM STEP (шаг настройки в FM-диапазоне)
1 Нажмите M.C., чтобы выбрать шаг настрой-
ки в FM-диапазоне.
100 (100 кГц)50 (50 кГц)
SP-P/O MODE (настройка выхода заднего ка-
нала и предварительного усилителя)
Выход на провода заднего громкоговорителя и
выход заднего канала RCA можно использо-
вать для подключения широкополосного гром-
коговорителя или сабвуфера. Выберите
настройку, подходящую для Вашего соедине-
ния.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора настрой-
ки.
! REAR/SUB.W Выберите, если к выходу
заднего канала подсоединен широкопо-
лосный громкоговоритель, и также
имеется сабвуфер, подсоединенный к
выходу RCA.
! SUB.W/SUB.W Выберите, если сабву-
фер подключен напрямую к выходу за-
днего канала без дополнительного
усилителя, и также имеется сабвуфер,
подсоединенный к выходу RCA.
! REAR/REAR Выберите, если широко-
полосный громкоговоритель подсоеди-
нен к выходу заднего канала и к выходу
RCA.
Если к выходу заднего канала подсое-
динен широкополосный громкоговори-
тель, а выход RCA не используется,
можно выбрать REAR/SUB.W или REAR/
REAR.
Меню системы
1 Нажмите и удерживайте кнопку SRC/
OFF, пока устройство не выключится.
2 Нажмите кнопку SRC/OFF и удерживай-
те ее, пока не откроется стартовое меню.
3 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
4 Для выбора функции меню системы
поворачивайте M.C.
Подробную информацию см. в
Меню систе-
мы
на стр. 112.
Использование
дополнительного
источника сигнала (AUX)
1 Вставьте мини-штекер стереокабеля в
гнездо AUX.
2 Нажмите кнопку SRC/OFF, чтобы вы-
брать AUX в качестве источника сигнала.
Примечание
Невозможно выбрать AUX, если не включе-
на вспомогательная настройка. Подробную
информацию см. в разделе
AUX (вспомога-
тельный вход)
на стр. 112.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! Название источника
! Название источника сигнала и часы
Если открылся неверный
экран
Отключите неверный экран, как описано
ниже.
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
3 Поверните M.C., чтобы отобразить
DEMO OFF, затем нажмите.
4 Поверните M.C. для выбора YES.
5 Нажмите M.C. для выбора.
Русский
Использование данного устройства
113
Раздел
Использование данного устройства
Ru
02
Black plate (114,1)
Соединения
Важно
! При установке данного устройства в авто-
мобиле, в котором отсутствует положение
ключа зажигания АСС, красный кабель
должен быть подключен к клемме, кото-
рая определяет рабочее положение
ключа зажигания; в противном случае
может возникнуть утечка тока аккумуля-
торной батареи.
O
N
S
T
A
R
T
O
F
F
Положение ACC Положение ACC от-
сутствует
! Эксплуатация данного устройства в усло-
виях, отличных от описанных ниже, может
привести к пожару или сбою в работе ус-
тройства.
Транспортные средства с 12-вольтовым
аккумулятором и заземлением отрица-
тельного полюса.
Громкоговорители с 50 Вт (выходная мощ-
ность) иот4 W до 8 W (сопротивление).
! Во избежание короткого замыкания, пере-
грева или неисправностей обязательно
соблюдайте следующие указания.
Перед установкой отсоедините отрица-
тельную клемму аккумулятора.
Закрепите провода при помощи зажимов
или изоляционной ленты. Для защиты
проводки заизолируйте провода в местах
их соприкосновения с металлическими де-
талями.
Разместите все кабели в удалении от под-
вижных деталей, таких как рычаг пере-
ключения передач и направляющие
сидений.
Разместите все кабели в удалении от на-
гревающихся деталей, таких как решетка
обогревателя.
Запрещается подключать желтый провод
дисплея к аккумуляторной батарее авто-
мобиля через сверленое отверстие в отсе-
ке двигателя.
Изолируйте концы всех не подсоединен-
ных кабелей изоляционной лентой.
Не укорачивайте кабели.
Никогда не срезайте изоляцию со шнура
питания данного устройства с целью пода-
чи питания на другое устройство. Допусти-
мая нагрузка кабеля по току ограничена.
Используйте предохранитель с указанны-
ми параметрами.
Запрещается напрямую заземлять отри-
цательный вывод громкоговорителя.
Запрещается связывать вместе отрица-
тельные кабели нескольких громкоговори-
телей.
! При включении питания устройства упра-
вляющий сигнал подается через сине-
белый провод. Подключите этот провод к
клемме пульта управления внешнего уси-
лителя мощности или клемме реле упра-
вления антенны с электроприводом
(макс. 300 мА 12 В постоянного тока).
Если автомобиль оборудован встроенной
в оконное стекло антенной, подсоедините
провод к клемме питания усилителя ан-
тенны.
! Запрещается подсоединять сине-белый
кабель к клемме питания внешнего усили-
теля мощности. Также запрещается под-
соединять данный провод к клемме
питания антенны с электроприводом. В
противном случае может возникнуть утеч-
ка тока аккумуляторной батареи или иная
неисправность.
! Черный кабель является заземляющим.
Заземляющие кабели данного устройства
и других устройств (особенно устройств,
предназначенных для эксплуатации при
больших токах, таких как усилитель мощ-
ности) должны монтироваться отдельно.
В противном случае их случайное отсое-
динение может привести к пожару или не-
исправности.
Данное устройство
3
1 24
5
1 Гнездо антенны
2 Плавкий предохранитель (10 A)
3 Гнездо шнура питания
4 Вход проводного пульта дистанционного
управления
Служит для подключения проводного
адаптера пульта дистанционного упра-
вления (приобретается отдельно).
5 Выход заднего канала или выход сабву-
фера
Шнур питания
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 К гнезду шнура питания
2 В зависимости от типа автомобиля функ-
ции 3 и 5 могут отличаться. В этом слу-
чае следует подключить 4 к 5 и 6 к 3.
3 Желтый
Резервный разъем (или разъем дополни-
тельного оборудования)
4 Желтый
Подключите к клемме источника постоян-
ного тока 12 В.
5 Красный
Разъем дополнительного оборудования
(или резервный разъем)
6 Красный
Подключите к клемме, на которую подает-
ся напряжение (12 В постоянного тока)
при включении зажигания.
7 Подсоедините провода одинакового
цвета друг к другу.
8 Черный (заземление на массу)
Установка
114
Раздел
Установка
Ru
03
Black plate (115,1)
9 Синий/белый
Расположение штекера разъема ISO на
различных автомобилях может отличать-
ся. Если штекер 5 предназначен для
управления антенной, подсоедините 9 к
b. На других автомобилях подключать 9
к b запрещается.
a Синий/белый
Подключите к клемме панели управления
усилителя мощности (макс. 300 мА 12 В
постоянного тока).
b Синий/белый
Подключите к клемме реле управления
антенны с электроприводом (макс.
300 мА 12 В постоянного тока).
c Желтый/черный
Если используется оборудование, имею-
щее функцию приглушения звука, данный
провод необходимо подсоединить к клем-
ме Audio Mute данного устройства. В про-
тивном случае необходимо проследить
за тем, чтобы данный провод не контакти-
ровал с любыми другими разъемами.
d Выводы громкоговорителей
Белый: Передний левый +
Белый/черный: Передний левый *
Серый: Передний правый +
Серый/черный: Передний правый *
Зеленый: Задний левый + или сабвуфер
+
Зеленый/черный: Задний левый * или
сабвуфер *
Фиолетовый: Задний правый + или саб-
вуфер +
Фиолетовый/черный: Задний правый *
или сабвуфер *
e Разъем ISO
В некоторых автомобилях разъем ISO
может иметь два вывода. В этом случае
необходимо подсоединить оба разъема.
Примечания
! Требуется изменение стартового меню
данного устройства. См.
SP-P/O MODE
(настройка выхода заднего канала и
предварительного усилителя)
на стр. 113.
Выход сабвуфера данного устройства мо-
нофонический.
! При использовании сабвуфера мощно-
стью 70 Вт (2 W) обязательно подсоедини-
те к сабвуферу фиолетовый и
фиолетовый/черный провод данного ус-
тройства. Не подсоединяйте зеленый и
зеленый/черный провода.
Усилитель мощности
(приобретается отдельно)
Используйте данную схему подсоединения
при использовании дополнительного усили-
теля мощности.
1
3
2
4
55
1 Пульт дистанционного управления систе-
мой
Подсоедините синий/белый кабель.
2 Усилитель мощности (приобретается от-
дельно)
3 Подключите с помощью кабелей RCA
(приобретаются отдельно)
4 К выходу заднего канала или выходу саб-
вуфера
5 Задний громкоговоритель или сабвуфер
Установка
Важно
! Перед окончательной установкой про-
верьте все соединения и системы.
! Не используйте детали, не разрешенные
производителем к использованию, по-
скольку это может стать причиной неис-
правностей.
! Уточните у дилера компании, требует ли
установка сверления отверстий или вне-
сения иных изменений в конструкцию ав-
томобиля.
! Не устанавливайте данное устройство в
местах, где оно может:
помешать управлению автомобилем.
травмировать пассажира при внезапной
остановке автомобиля.
! Перегрев полупроводникового лазера
приведет к его выходу из строя. Разме-
стите все кабели в удалении от нагреваю-
щихся деталей, таких как решетка
обогревателя.
! Оптимальной является установка устрой-
ства под углом менее 60°.
60°
! При установке необходимо обеспечить
эффективный отвод тепла, оставив до-
статочное пространство за задней пане-
лью и закрепив свободные кабели так,
чтобы они не закрывали вентиляционные
отверстия.
5cmcm
5 см
5 см
Оставить
просторное
место
! При установке используйте детали, имею-
щиеся в продаже.
Порядок установки
Данное устройство можно устанавливать
одним из описанных ниже способов.
! Установка с кронштейном
! Установка с помощью резьбовых отвер-
стий на боковых панелях устройства
Перед установкой данного
устройства
1 Снимите рамку.
1
1 Декоративная рамка
2 Вставьте прилагаемые экстракторы с
обеих сторон устройства до щелчка.
3 Извлеките устройство из кронштейна.
Снимите кронштейн.
Русский
Установка
115
Раздел
Установка
Ru
03
Black plate (116,1)
1
1 Кронштейн
(входит в комплект поставки)
Установка с кронштейном
1 Установите кронштейн на приборную
панель.
После установки кронштейна на приборную
панель выберите подходящие фиксаторы,
исходя из толщины материала приборной
панели, и подогните их.(С помощью верхних
и нижних фиксаторов закрепите данное ус-
тройство как можно надежнее. Для надеж-
ной фиксации устройства необходимо
подогнуть фиксаторы на 90 градусов.)
1
2
1 Приборная панель
2 Кронштейн
(входит в комплект поставки)
2 Установите устройство.
1
1 Приборная панель
3 Установите рамку.
1
1 Декоративная рамка
Извлечение кронштейна
Порядок действий тот же, что перед установ-
кой устройства. Подробнее см. в разделе
Перед установкой данного устройства
на
стр. 115.
Установка с помощью
резьбовых отверстий на
боковых панелях устройства
% Крепление устройства на заводской
установочный кронштейн.
Расположите устройство таким образом,
чтобы его резьбовые отверстия совпадали с
резьбовыми отверстиями кронштейна, иза-
тяните по три винта на каждой стороне.
1
2
4
3
1 Подогните зажим, если он мешает уста-
новке.
2 Заводской установочный кронштейн
3 Крепежные (5 мм ×8мм) винты
4 Приборная панель или консоль
Установка
116
Раздел
Установка
Ru
03
Black plate (117,1)
Устранение неисправностей
Симптомы выделены жирным шрифтом;
причины показаны обычным шрифтом без
отступа. Способы устранения показаны обы-
чным шрифтом с отступом.
Дисплей автоматически возвращается в
исходный режим.
В течение 30 секунд не было выполнено никаких
операций.
Повторите операцию.
Диапазон повторного воспроизведения само-
произвольно изменяется.
В зависимости от выбранного диапазона вос-
произведения он может изменяться при выборе
другой папки или дорожки, а также при перемот-
ке вперед/назад.
Выберите диапазон повторного
воспроизведения еще раз.
Вложенная папка не воспроизводится.
Вложенные папки не воспроизводятся, если вы-
бран диапазон FLD (повторное воспроизведение
папки).
Выберите другой диапазон повторного
воспроизведения.
При изменении дисплея отображается
NO XXXX (например, NO TITLE).
Текстовая информация отсутствует.
Переключите дисплей или включите
воспроизведение другой дорожки/файла.
Устройство функционирует с ошибками.
Имеются помехи.
Используется устройство, например, сотовый те-
лефон, которое может вызывать шумовые поме-
хи.
Уберите прибор, вызывающий помехи, от
этого устройства.
Сообщения об ошибках
Прежде чем обратиться к торговому пред-
ставителю или в ближайший сервисный
центр Pioneer, обязательно запомните сооб-
щение об ошибке.
Сообщения об ошибках выделены жирным
шрифтом; причины показаны обычным
шрифтом без отступа. Способы устранения
показаны обычным шрифтом с отступом.
Общие
AMP ERROR
Устройство не работает или неправильно под-
соединен громкоговоритель; сработала цепь за-
щиты.
Проверьте, подключен ли громкоговоритель.
Если сообщение не исчезает даже после
выключения/выключения зажигания,
свяжитесь с дилерским центром или
авторизованным сервисным центром Pioneer.
Проигрыватель компакт-дисков
ERROR-07, 11, 12, 17, 30
Диск загрязнен.
Очистите диск.
Диск поцарапан.
Замените диск.
ERROR-07, 10, 11, 12, 15, 17, 30, A0
Электрическая или механическая неисправ-
ность.
Установите ключ зажигания в положение
OFF, а затем в положение ON или
переключитесь на другой источник сигнала, а
затем обратно на проигрыватель компакт-
дисков.
ERROR-15
Вставлен пустой диск.
Замените диск.
ERROR-23
Формат диска не поддерживается.
Замените диск.
FORMAT READ
Иногда происходит задержка между началом
воспроизведения и появлением звука.
Звук появится после того как с дисплея
исчезнет сообщение.
NO AUDIO
На диске отсутствуют файлы, которые можно
воспроизвести.
Замените диск.
SKIPPED
Диск содержит файлы, защищенные техноло-
гией DRM.
Защищенные файлы пропускаются.
PROTECT
Все файлы на диске защищены технологией
DRM.
Замените диск.
Запоминающее устройство USB/iPod
FORMAT READ
Иногда происходит задержка между началом
воспроизведения и появлением звука.
Звук появится после того как с дисплея
исчезнет сообщение.
NO AUDIO
Композиции отсутствуют.
Перенесите аудиофайлы на запоминающее
устройство USB и подключите его.
На подключенном запоминающем устройстве
USB включена функция защиты от перезаписи.
Отключите функцию защиты от перезаписи в
соответствии с инструкцией по эксплуатации
запоминающего устройства USB.
SKIPPED
На подключенном запоминающем устройстве
USB содержатся файлы, защищенные техноло-
гией DRM.
Защищенные файлы пропускаются.
PROTECT
Все файлы на подключенном запоминающем ус-
тройстве USB защищены технологией DRM.
Замените запоминающее устройство USB.
N/A USB
Подключенное устройство USB не поддержи-
вается данным устройством.
! Подключите запоминающее устройство
USB класса Mass Storage.
! Отсоедините устройство и замените его на
совместимое запоминающее устройство
USB.
Русский
Дополнительная информация
117
Приложение
Дополнительная информация
Ru
Black plate (118,1)
CHECK USB
Короткое замыкание на разъеме USB или в кабе-
ле USB.
Убедитесь, что разъем USB или кабель USB
не защемлен и не поврежден.
CHECK USB
Подключенное запоминающее устройство USB
потребляет больше максимально допустимой
силы тока.
Отсоедините запоминающее устройство USB
и не используйте его. Установите ключ
зажигания в положение OFF, затем в
положение ACC или ON, и затем
подключайте только совместимые
запоминающие устройства USB.
CHECK USB
iPod работает, но не подзаряжается.
Убедитесь в отсутствии короткого замыкания
в кабеле iPod (например, что кабель не зажат
между металлическими предметами). После
проверки кабеля установите ключ зажигания
в положение OFF, а затем в положение ON,
либо отключите и заново подключите iPod.
ERROR-19
Сбой связи.
Выполните следующие действия.
Установите ключ зажигания в положение
OFF, а затем в положение ON.
Отключите запоминающее устройство USB.
Выберите другой источник сигнала.
Затем вновь выберите USB в качестве
источника сигнала.
Сбой iPod.
Отключите кабель от iPod. После появления
на дисплее главного меню iPod заново
подключите iPod и перезагрузите его.
ERROR-23
Запоминающее устройство USB не отформати-
ровано в системе FAT12, FAT16 или FAT32.
Запоминающее устройство USB должно быть
форматировано в FAT12, FAT16 или FAT32.
ERROR-16
Устаревшая версия прошивки iPod.
Обновите версию прошивки iPod.
Сбой iPod.
Отключите кабель от iPod. После появления
на дисплее главного меню iPod заново
подключите iPod и перезагрузите его.
STOP
В текущем списке отсутствуют композиции.
Выберите список, содержащий музыкальные
композиции.
NOT FOUND
Композиций не найдено.
Загрузите композиции на iPod.
Приложение
START UP APP
Приложение еще не запущено.
Следуйте экранным подсказкам.
Рекомендации по
обращению с изделием
Диски и проигрыватель
Используйте только диски, имеющие один из
следующих логотипов.
Используйте 12-см диски.
Используйте только обычные круглые диски.
Следующие типы дисков нельзя использовать
на данном устройстве:
! Диски формата DualDisc
! 8-см диски: попытки использовать такие
диски с помощью адаптера могут привести
к неисправности устройства.
! Диски необычных форм
! Диски других форматов, кроме CD
! Поврежденные диски, вт.ч. с трещинами, с
отколотыми краями или деформированные
! Диски CD-R/RW, запись на которых не
была завершена
Не прикасайтесь к записанной поверхности
дисков.
Когда диски не используются, храните их в
футлярах.
Не приклеивайте этикеток, не пишите и не на-
носите химических веществ на поверхность
дисков.
Для очистки компакт-диска протрите диск мяг-
кой тканью от центра к краю.
Конденсация может временно ухудшить рабо-
ту проигрывателя. Оставьте его для адаптации
к более высокой температуре примерно на
час. Также удалите влагу с дисков с помощью
мягкой ткани.
Воспроизведение дисков может быть невоз-
можно из-за характеристик диска, формата
диска, приложения, при помощи которого вы-
полнялась запись, условий воспроизведения,
условий хранения и других факторов.
Толчки от неровностей дороги могут вызвать
прерывание воспроизведения диска.
При использовании дисков, на поверхность ко-
торых могут наноситься этикетки, изучите ин-
струкции и предупреждения для этих дисков.
Установка и извлечение некоторых дисков
могут быть невозможны. Использование таких
дисков может привести к повреждению обору-
дования.
Не приклеивайте на диски этикетки и другие
материалы.
! Это может деформировать диски, в резуль-
тате чего их воспроизведение будет невоз-
можным.
! Этикетки могут отклеиться во время вос-
произведения и затруднить извлечение
дисков, а также повредить оборудование.
Запоминающее устройство USB
Подключение через USB-концентратор не под-
держивается.
Не подключайте другие устройства, кроме за-
поминающих устройств USB.
Дополнительная информация
118
Приложение
Дополнительная информация
Ru
Black plate (119,1)
При движении автомобиля надежно закрепите
запоминающее устройство USB. Не роняйте
запоминающее устройство USB на пол, где
оно может застрять под педалью тормоза или
акселератора.
В зависимости от типа запоминающего устрой-
ства USB могут возникнуть следующие про-
блемы.
! Управление функциями может отличаться.
! Запоминающее устройство может не рас-
познаваться.
! Файлы не могут воспроизводиться коррект-
но.
! Устройство может создавать шумовые по-
мехи во время прослушивания радио.
iPod
Не оставляйте iPod в местах с высокой темпе-
ратурой воздуха.
При движении автомобиля надежно закрепите
iPod. Не роняйте iPod на пол, где он может за-
стрять под педалью тормоза или акселерато-
ра.
Настройки iPod
! При подключении iPod к данному устрой-
ству эквалайзер iPod автоматически отклю-
чается, что обеспечивает оптимальное
звучание. При отсоединении iPod для эква-
лайзера автоматически выбирается пред-
ыдущая настройка.
! При использовании данного устройства от-
ключение функции повторного воспроизве-
дения на iPod невозможно. Если iPod
подключен к данному устройству, будет ав-
томатически выбран режим повтора всех
композиций.
Текстовая информация несовместимого фор-
мата, сохраненная на iPod, не будет отобра-
жаться на дисплее данного устройства.
Поддержка сжатых
аудиофайлов (компакт-
диск, USB)
WMA
Расширение: .wma
Скорость передачи данных: от 48 кбит/сдо
320 кбит/с (постоянная), от 48 кбит/сдо
384 кбит/с (переменная)
Частота дискретизации:32кГц, 44,1 кГц,48кГц
Windows MediaäAudio Professional, Lossless,
Voice/DRM Stream/Stream с поддержкой видео:
не поддерживается
MP3
Расширение: .mp3
Скорость передачи данных: от 8 кбит/сдо
320 кбит/с (постоянная), переменная
Частота дискретизации: от 8 кГц до 48 кГц
(32 кГц, 44,1 кГц,48кГц пиковая)
Совместимая версия тегов ID3: 1.0, 1.1, 2.2,
2.3, 2.4 (теги ID3 версии 2.x имеют приоритет
перед версией 1.x.)
Списки воспроизведения M3u: не поддержи-
ваются
MP3i (интерактивный MP3), mp3 PRO: не под-
держиваются
WAV
Расширение: .wav
Разрядность квантования:8и 16 (LPCM), 4
(MS ADPCM)
Частота дискретизации: от 16 кГц до 48 кГц
(LPCM), 22,05 кГц и 44,1 кГц (MS ADPCM)
! Эта функция не работает, если выбрано
USB MTP.
Дополнительная информация
В качестве названия файла или папки могут
отображаться только первые 32 символа
(включая расширение).
Для отображения в данном устройстве коди-
ровка русского текста должна соответствовать
одному из следующих наборов символов:
! Юникод (UTF-8, UTF-16)
! Отличный от Юникода набор символов, ис-
пользующийся в среде Windows, для кото-
рого в языковой настройке задан русский
язык
Это устройство может работать некорректно в
зависимости от приложений, использованных
для кодирования файлов WMA.
При начале воспроизведения аудиофайлов,
содержащих изображения, и файлов с запоми-
нающего устройства USB, содержащего разве-
твленные иерархии папок, может происходить
небольшая задержка.
Диск
Допустимая иерархия папок: до восьми уров-
ней (реальная иерархия папок составляет
менее двух уровней)
Количество воспроизводимых папок: не более
99
Количество воспроизводимых файлов: не
более 999
Файловая система: ISO 9660 уровень 1 и 2,
Romeo, Joliet
Воспроизведение нескольких сессий: поддер-
живается
Пакетный формат записи: не поддерживается
Независимо от продолжительности паузы
между композициями в изначальной записи,
при воспроизведении дисков со сжатыми ауди-
офайлами между композициями будут корот-
кие паузы.
Запоминающее устройство USB
Допустимая иерархия папок: до восьми уров-
ней (реальная иерархия папок составляет
менее двух уровней)
Количество воспроизводимых папок: не более
500
Количество воспроизводимых файлов: не
более 15 000
Воспроизведение защищенных от копирова-
ния файлов: не поддерживается
Русский
Дополнительная информация
119
Приложение
Дополнительная информация
Ru
Black plate (120,1)
Запоминающее устройство USB, содержащее
разделы: воспроизводится только первый раз-
дел.
При начале воспроизведения аудиофайлов на
запоминающем устройстве USB, содержащем
разветвленные иерархии папок, может возни-
кать небольшая задержка.
ВНИМАНИЕ
! Pioneer не гарантирует совместимость со
всеми устройствами USB mass storage и
не несет ответственности за любую поте-
рю данных на медиапроигрывателях,
смартфонах и других устройствах при ис-
пользовании этого изделия.
! Не оставляйте диски или запоминающее
устройство USB в местах с высокой тем-
пературой воздуха.
Поддержка iPod
Данное устройство поддерживает только ни-
жеперечисленные модели iPod.
Сделано для
! iPod touch (5-го поколения)
! iPod touch (4-го поколения)
! iPod touch (3-го поколения)
! iPod touch (2-го поколения)
! iPod touch (1-го поколения)
! iPod classic
! iPod с поддержкой видео
! iPod nano (7-го поколения)
! iPod nano (6-го поколения)
! iPod nano (5-го поколения)
! iPod nano (4-го поколения)
! iPod nano (3-го поколения)
! iPod nano (2-го поколения)
! iPod nano (1-го поколения)
! iPhone 5
! iPhone 4S
! iPhone 4
! iPhone 3GS
! iPhone 3G
! iPhone
В зависимости от версии программного обес-
печения или поколения iPod некоторые функ-
ции могут быть недоступны.
Функции iPod могут различаться в зависимо-
сти от версии программного обеспечения.
Пользователям iPod с интерфейсом Lightning
потребуется кабель Lightning - USB (входит в
комплект поставки iPod).
Пользователям iPod с интерфейсом Dock Con-
nector потребуется кабель CD-IU51. Подроб-
ную информацию можно получить по месту
покупки.
О совместимости файлов/форматов см. вру-
ководствах к iPod.
Аудиокниги, подкасты: поддерживаются
ВНИМАНИЕ
Компания Pioneer не несет ответственности
за потерю данных на iPod, даже если эти
данные будут потеряны во время использо-
вания данного устройства.
Последовательность
воспроизведения
аудиофайлов
Пользователь не может назначать номера
папок и устанавливать последовательность
воспроизведения с помощью данного ус-
тройства.
Пример иерархии
1
2
3
4
5
6
01
02
03
04
05
: Папка
: Сжатый ауди-
офайл
от 01 до 05: Номер
папки
от 1 до 6: После-
довательность
воспроизведения
Диск
Последовательность выбора папок и других
действий может отличаться в зависимости
от кодировки или программного обеспече-
ния, использованного для записи.
Запоминающее устройство USB
Файлы воспроизводятся в той последова-
тельности, в которой они записаны на запо-
минающем устройстве USB.
Для выбора алгоритма воспроизведения ре-
комендуется выполнить следующие дей-
ствия.
1 Присвойте файлам имена с цифрами,
определяющими последовательность
воспроизведения (например, 001xxx.mp3
и 099yyy.mp3).
2 Поместите эти файлы в папку.
3 Сохраните папку, содержащую файлы, на
запоминающем устройстве USB.
Учитывайте, что в некоторых системных сре-
дах невозможно установить порядок вос-
произведения.
Последовательность воспроизведения фай-
лов на портативном аудиоплеере USB может
изменяться и зависит от типа плеера.
Таблица символов для
русского языка
Д: БД: БД: БД: БД: Б
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
Д: Дисплей Б: Буква
Авторское право и
товарные знаки
MP3
Поставка этого изделия дает право только на
его частное и некоммерческое использова-
ние и не предоставляет лицензии и не подра-
зумевает право использования этого
изделия в любых коммерческих (т.е. прино-
сящих прибыль) прямых трансляциях (теле-
визионных, спутниковых, кабельных и/или
любых других), вещании/потоковой передаче
через Интернет, локальных сетях и/или дру-
гих сетях или в других электронных системах
распространения, таких как системы платно-
го аудио и аудио по запросу. Для такого ис-
пользования необходима специальная
лицензия. Дополнительную информацию см.
на сайте
http://www.mp3licensing.com.
WMA
Windows Media это зарегистрированная
торговая марка или торговая марка Microsoft
Corporation в США и/или других странах.
Дополнительная информация
120
Приложение
Дополнительная информация
Ru
Black plate (121,1)
В данном изделии используются технологии,
принадлежащие корпорации Microsoft, кото-
рые не разрешается использовать или рас-
пространять без лицензии от Microsoft
Licensing, Inc.
iPod и iPhone
iPhone, iPod, iPod classic, iPod nano и iPod
touch являются товарными знаками компа-
нии Apple Inc., зарегистрированными в США
и других странах.
Lightning является торговым знаком компа-
нии Apple Inc.
Made for iPod и Made for iPhone означает,
что электронный прибор был разработан с
целью подключения определенно к iPod или
iPhone соответственно, и имеется сертифи-
цикация разработчика о соответствии с тех-
ническими характеристиками Apple. Apple не
несет ответственности за работу данного ус-
тройства или его соответствие со стандарта-
ми по технике безопасности или
регулятивными нормами. Пожалуйста, об-
ратите внимание, что использование данно-
го прибора с iPod или iPhone может
отрицательно сказываться на качестве бес-
проводной связи.
Androidä
Android является товарным знаком компании
Google Inc.
Серийный номер
На этом рисунке показана информация о месяце и годе изготовления устройства.
L
Го д
Го д
Символ
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
2011 2012 2013 2014 2015 2016 2017 2018 2019 2020
K LMNO P QRS T
ABCDEFGH I JСимвол
P1 - Год изготовления
1
Символ
2345 6 7 89 1110 12
ABCDEFGH I JKL
Месяц
P2 - Месяц изготовления
12 цифр
P1 P2
Дата изготовления оборудования
2 цифры
10 цифр
Русский
Дополнительная информация
121
Приложение
Дополнительная информация
Ru
Black plate (122,1)
Технические характеристики
Общие
Источник питания ........... 14,4 В постоянного тока (до-
пустимый диапазон от 10,8
Вдо15,1 В)
Система заземления ..... Заземление отрицательно-
го полюса
Максимальный потребляемый ток
................................... 10,0 А
Размеры (Ш × В × Г):
DIN
Шасси ............................. 178 мм × 100 мм × 157 мм
Передняя панель ........... 188 мм ×118мм ×25мм
D
Шасси ............................. 178 мм × 100 мм × 165 мм
Передняя панель ........... 170 мм ×96мм ×17мм
Масса ............................. 1,2 кг
Аудио
Максимальная выходная мощность
................................... 50 Вт ×4
70 Вт × 1/2 W (для сабвуфе-
ра)
Номинальная выходная мощность
................................... 22 Вт ×4(от 50 Гц до
15 000 Гц, суммарное значе-
ние коэффициента нели-
нейных искажений 5%,
нагрузка 4 W для обоих ка-
налов)
Сопротивление нагрузки
................................... 4 W (допустимо от 4 W до
8 W )
Максимальная выходная мощность
................................... 2,0 В
Контур громкости ........... +10 дБ (100 Гц), +6,5 дБ
(10 кГц)(громкость: 30 дБ)
Эквалайзер (5-полосный графический эквалайзер):
Частота ........................... 80 Гц/250 Гц/800 Гц/2,5 кГц/
8 кГц
Диапазон амплитудно-частотных характеристик
................................... ±12 дБ (сшагом2 дБ)
Сабвуфер (моно):
Частота ........................... 50 Гц/63 Гц/80 Гц/100 Гц/
125 Гц/160 Гц/200 Гц
Крутизна характеристики
................................... 12 дБ/окт, 24 дБ/окт
Усиление ........................ +6 дБ до 24 дБ
Фаза ............................... Нормальная/Обратная
Проигрыватель компакт-дисков
Система ......................... Аудиосистема с компакт-ди-
ском
Используемые диски ..... Компакт-диск
Отношение сигнал/шум
................................... 94 дБ (1 кГц)(сеть IEC-A)
Число каналов ............... 2(стерео)
Формат декодирования файлов MP3
................................... MPEG- 1 и 2 Audio Layer 3
Формат декодирования файлов WMA
................................... Версии 7, 7.1, 8, 9, 10, 11, 12
(двухканальный звук)
(Windows Media Player)
Формат сигнала WAV ..... Linear PCM и MS ADPCM
(без компрессии)
USB
Стандартная спецификация USB
................................... USB 2.0 полноскоростной
Максимальный ток питания
................................... 1 А
Класс USB ...................... MSC (Mass Sto rage Class)
Файловая система ......... FAT12, FAT16, FAT32
Формат декодирования файлов MP3
................................... MPEG- 1 и 2 Audio Layer 3
Формат декодирования файлов WMA
................................... Версии 7, 7.1, 8, 9, 10, 11, 12
(двухканальный звук)
(Windows Media Player)
Формат сигнала WAV ..... Linear PCM и MS ADPCM
(без компрессии)
FM-тюнер
Диапазон частот ............. от 87,5 МГц до 108,0 МГц
Полезная чувствительность
................................... 9 дБф (0,8 мкВ/75 W, моно,
отношение сигнал/шум:
30 дБ)
Отношение сигнал/шум
................................... 72 дБ (сеть IEC-A)
MW-тюнер
Диапазон частот ............. от 531 кГц до 1 602 кГц
Полезная чувствительность
................................... 25 мкВ (отношение сигнал/
шум:20дБ)
Отношение сигнал/шум
................................... 62 дБ (сеть IEC-A)
LW-тюнер
Диапазон частот ............. от 153 кГц до 281 кГц
Полезная чувствительность
................................... 28 мкВ (отношение сигнал/
шум:20дБ)
Отношение сигнал/шум
................................... 62 дБ (сеть IEC-A)
Примечание:
В соответствии со статьей 5 закона Рос-
сийской Федерации «О защите прав по-
требителей» и постановлением
правительства Российской Федерации
720 от 16.06.97 компания Pioneer Europe
NV оговаривает следующий срок службы
изделий, официально поставляемых на
российский рынок.
Автомобильная электроника:6лет
Прочие изделия (наушники, микрофоны
ит.п.): 5 лет
Примечания
! Характеристики и конструкция могут быть
изменены без предварительного уведо-
мления.
! Данное устройство произведено в Таи-
ланде.
Дополнительная информация
122
Приложение
Дополнительная информация
Ru
Black plate (123,1)
Русский
123Ru
Black plate (124,1)
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, JAPAN
Корпорация Пайонир
28-8, Хонкомагомэ 2-чоме, Бункё-ку,
Токио 113-0021, Япония
Импортер ООО ПИОНЕР РУС
105064, Россия, г. Москва, Нижний Сусальный переулок, дом 5, строение
19
Тел.: +7(495) 956-89-01
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346
TEL: 65-6378-7888
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MÉXICO S.A. de C.V.
Blvd.Manuel Ávila Camacho 138, 10 piso
Col.Lomas de Chapultepec, México, D.F. 11000
TEL: 52-55-9178-4270
FAX: 52-55-5202-3714
台北4078
886-(0)2-2657-3588
9095
852-2848-6488
ã 2013-2016 PIONEER CORPORATION. All rights reserved.
ã 2013-2016 PIONEER CORPORATION. Tous droits de reproduction et de traduction réservés.
ã PIONEER CORPORATION, 2013-2016. Все права защищены.
<QRD3247-B> EW
<KOKZ16E>

Transcripción de documentos

Black plate (1,1) Français Español Deutsch Owner’s Manual Mode d’emploi Manuale d’istruzioni Manual de instrucciones Bedienungsanleitung Handleiding Руководство пользователя Italiano FH-460UI English CD RDS RECEIVER AUTORADIO CD RDS SINTOLETTORE CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS CD RDS-EMPFÄNGER CD RDS-ONTVANGER CD RDS ПРИЕМНИК Nederlands Русский <QRD3247-B> 1 Black plate (2,1) Section Before you start 01 Thank you for purchasing this PIONEER product To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference. Before you start About this unit The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS (radio data system) function only works in areas that broadcast RDS signals for FM stations. WARNING If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. 2 ! Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards. ! Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the device. CAUTION This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007. If you experience problems Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service Station. CAUTION ! Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids. ! The Pioneer CarStereo-Pass is for use only in Germany. ! Always keep the volume low enough to hear outside sounds. ! Avoid exposure to moisture. En <QRD3247-B> 2 Black plate (3,1) Section Using this unit Using this unit Head unit 3 4 2 1 5 3 4 5 6 7 9 8 Turn M.C. to switch to YES. # If you do not use the unit for 30 seconds, the set up menu will not be displayed. # If you prefer not to set up at this time, turn M.C. to switch to NO. 5 To finish your settings, turn M.C. to select YES. # If you prefer to change your setting again, turn M.C. to switch to NO. 6 3 a 1 6 7 89 1 h (eject) 2 iPod 3 1/ 4 Disc loading slot 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d 9 MULTI-CONTROL (M.C.) a b (iPod control) This unit’s iPod function is operated from your iPod. 3 Sub information section 4 TA (traffic announcements) 5 TP (traffic program identification) 6 7 8 9 (iPod control) a (back)/DIMMER (dimmer) (list) c AUX input jack (3.5 mm stereo jack) d USB port (list) 2 a b cd to 6/ b (sound retriever) LOC (local seek tuning) (repeat) (random) Main information section ! Tuner: band and frequency ! RDS: program service name, PTY information and other literal information ! CD player, USB storage device and iPod: elapsed playback time and text information 4 Follow these steps to set the menu. To proceed to the next menu option, you need to confirm your selection. LANGUAGE (multi-language) This unit can display the text information from a compressed audio file even for information embedded in English, Russian or Turkish. ! If the embedded language and the selected language setting are not the same, text information may not display properly. ! Some characters may not be displayed properly. 1 Turn M.C. to select the desired setting. ENG (English)—РУС (Russian)—TUR (Turkish) 2 Press M.C. to confirm the selection. CLOCK SET (setting the clock) 1 2 3 4 Turn M.C. to adjust hour. Press M.C. to select minute. Turn M.C. to adjust minute. Press M.C. to confirm the selection. FM STEP (FM tuning step) b Appears when a lower tier of folder or menu exists. CAUTION Use an optional Pioneer USB cable (CD-U50E) to connect the USB storage device as any device connected directly to the unit will protrude out from the unit, which could be dangerous. Press M.C. to select. Set up menu 1 After installation of this unit, turn the ignition switch to ON. SET UP appears. Use FM STEP to set FM tuning step options (seek step settings). 1 Turn M.C. to select the FM tuning step. 100 (100 kHz)—50 (50 kHz) 2 Press M.C. to confirm the selection. QUIT appears. ! The manual tuning step is fixed at 50 kHz. ! When AF and TA are turned off, the seek step is fixed at 50 kHz even if set to 100. English 1 2 2 Display indication 02 Press M.C. to select. Notes ! You can set up the menu options from the system menu and initial menu. For details about the settings, refer to System menu on page 8 and Initial menu on page 9. ! You can cancel set up menu by pressing SRC/OFF. Basic operations Turning the unit on 1 Press SRC/OFF to turn the unit on. Turning the unit off 1 Press and hold SRC/OFF until the unit turns off. Selecting a source 1 Press SRC/OFF to cycle between: RADIO—CD—USB/iPod—APP (application)— AUX ! USB MTP displays while the MTP connection is in use. ! When there is an iPod connected and a source other than iPod is selected, you can switch to iPod by pressing iPod. Adjusting the volume 1 Turn M.C. to adjust the volume. Note When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off. En <QRD3247-B> 3 3 Black plate (4,1) Section Using this unit 02 Frequently used menu operations Returning to the previous display Returning to the previous list (the folder one level higher) 1 Press /DIMMER. Returning to the ordinary display Canceling the main menu 1 Press BAND/ . Returning to the ordinary display from the list 1 Press BAND/ . Radio Basic operations Selecting a band 1 Press BAND/ until the desired band (FM1, FM2,FM3 for FM or MW/LW) is displayed. Switching preset stations 1 Press c or d. ! Select PCH (preset channel) under SEEK to use this function. Manual tuning (step by step) 1 Press c or d. ! Select MAN (manual tuning) under SEEK to use this function. Seeking 1 Press and hold c or d, and then release. You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d. Notes ! For details about SEEK, refer to SEEK (left/ right key setting) on page 5. 4 Using this unit ! This unit’s AF (alternative frequencies search) function can be turned on and off. AF should be off for normal tuning operation (refer to AF (alternative frequencies search) on page 4). Storing and recalling stations for each band Using preset tuning buttons 1 To store: Press and hold down one of the preset tuning buttons (1/ to 6/ ) until the number stops flashing. 2 To recall: Press one of the preset tuning buttons (1/ to 6/ ). Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: ! FREQUENCY (program service name or frequency) ! BRDCST INFO (program service name/PTY information) ! CLOCK (source name and clock) Notes ! If the program service name cannot be acquired in FREQUENCY, the broadcast frequency is displayed instead. If the program service name is detected, the program service name will be displayed. ! Depending on the band, text information can be changed. ! Text information items that can be changed depend on the area. Searching for an RDS station by PTY information (list). 1 Press 2 Turn M.C. to select a program type. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Press M.C. to begin the search. The unit searches for a station broadcasting that type of program. When a station is found, its program service name is displayed. ! To cancel the search, press M.C. again. ! The program of some stations may differ from that indicated by the transmitted PTY. ! If no station is broadcasting the type of program you searched for, NOT FOUND is displayed for about two seconds and then the tuner returns to the original station. PTY list For more details about PTY list, visit the following site: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html FM SETTING (FM sound quality settings) The sound quality level can be set to match the broadcast signal conditions of the FM band signal. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. ! STANDARD – This is the standard setting. ! HI-FI – This is the setting to use to prioritize the high quality of stereo sound. ! STABLE – This is the setting to use to prioritize the low noise of monaural sound. BSM (best stations memory) BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on. To cancel, press M.C. again. REGIONAL (regional) Function settings When AF is used, the regional function limits the selection of stations to those broadcasting regional programs. 1 Press M.C. to turn the regional function on or off. 1 LOCAL (local seek tuning) Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. Once selected, the following functions can be adjusted. # If MW/LW band is selected, only BSM, LOCAL and SEEK are available. Local seek tuning allows you to tune in to only those radio stations with sufficiently strong signals for good reception. 1 Press M.C. to select the desired setting. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations. TA (traffic announcement standby) Using PTY functions You can tune in to a station using PTY (program type) information. 1 Press M.C. to turn traffic announcement standby on or off. AF (alternative frequencies search) En <QRD3247-B> 4 Black plate (5,1) Section Using this unit NEWS (news program interruption) 1 Press M.C. to turn the NEWS function on or off. SEEK (left/right key setting) You can assign a function to the left and right keys of the unit. Select MAN (manual tuning) to tune up or down manually or select PCH (preset channel) to switch between preset channels. 1 Press M.C. to select MAN or PCH. Stopping playback of files on a USB storage device 1 You may disconnect the USB storage device at any time. Selecting a folder 1 Press 1/ or 2/ . Selecting a track 1 Press c or d. Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no sound during fast forward or reverse. Returning to root folder 1 Press and hold BAND/ . CD/CD-R/CD-RW and USB storage devices MTP connection MTP-compatible Android devices (running Android OS 4.0 or higher) can be connected by MTP connection using the USB source. To connect an Android device, use the cable that came with the device. Note This function is not compatible with WAV. Basic operations Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with the label side up. Ejecting a CD/CD-R/CD-RW 1 Press h. Playing songs on a USB storage device 1 Open the USB port cover. 2 Plug in the USB storage device using a USB cable. Switching between compressed audio and CD-DA 1 Press BAND/ . Switching between playback memory devices You can switch between playback memory devices on USB storage devices with more than one Mass Storage Device-compatible memory device. 1 Press BAND/ . ! You can switch between up to 32 different memory devices. Note Disconnect USB storage devices from the unit when not in use. Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: CD-DA ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) CD-TEXT ! TRACK INFO (track title/track artist/disc title) ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) MP3/WMA/WAV ! TRACK INFO (track title/artist name/album title) ! FILE INFO (file name/folder name) ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) 02 Viewing a list of the files (or folders) in the selected folder 1 When a folder is selected, press M.C. Playing a song in the selected folder 1 When a folder is selected, press and hold M.C. Operations using special buttons Selecting a repeat play range 1 Press 6/ to cycle between the following: CD/CD-R/CD-RW ! ALL – Repeat all tracks ! ONE – Repeat the current track ! FLD – Repeat the current folder USB storage device ! ALL – Repeat all files ! ONE – Repeat the current file ! FLD – Repeat the current folder Selecting and playing files/ tracks from the name list Playing tracks in random order to turn random play on or off. 1 Press 5/ Tracks in a selected repeat range are played in random order. ! To change songs during random play, press d to switch to the next track. Pressing c restarts playback of the current track from the beginning of the song. 1 Press list mode. Pausing playback 1 Press 4/PAUSE to pause or resume. to switch to the file/track name 2 Use M.C. to select the desired file name (or folder name). Selecting a file or folder 1 Turn M.C. Playing 1 When a file or track is selected, press M.C. English 1 Press M.C. to turn AF on or off. Using this unit Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 3/S.Rtrv to cycle between: 1—2—OFF (off) 1 is effective for low compression rates, and 2 is effective for high compression rates. Function settings 1 Press M.C. to display the main menu. En <QRD3247-B> 5 5 Black plate (6,1) Section Using this unit 02 2 Turn M.C. to change the menu option and press to select FUNCTION. Once selected, the function below can be adjusted. S.RTRV (sound retriever) Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on page 5. Using this unit Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: ! TRACK INFO (track title/artist name/album title) ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) Browsing for a song iPod 1 Press search. Basic operations 2 to switch to the top menu of list Use M.C. to select a category/song. Playing songs on an iPod 1 Open the USB port cover. 2 Connect an iPod to USB input. Playback is performed automatically. Changing the name of the song or category 1 Turn M.C. Playlists—artists—albums—songs—podcasts —genres—composers—audiobooks Selecting a song (chapter) 1 Press c or d. Playing 1 When a song is selected, press M.C. Selecting an album 1 Press 1/ or 2/ . Viewing a list of songs in the selected category 1 When a category is selected, press M.C. Fast forwarding or reversing 1 Press and hold c or d. Playing a song in the selected category 1 When a category is selected, press and hold M.C. Notes ! The iPod cannot be turned on or off when the control mode is set to CTRL AUDIO. ! Disconnect headphones from the iPod before connecting it to this unit. ! The iPod will turn off about two minutes after the ignition is switched off. Searching the list by alphabet 1 When a list for the selected category is displayed, press to switch to alphabet search mode. ! You also can switch to alphabet search mode by turning M.C. twice. 2 Turn M.C. to select a letter. 3 Press M.C. to display the alphabetical list. ! To cancel searching, press /DIMMER. Notes ! You can play playlists created with the computer application (MusicSphere). The application will be available on our website. ! Playlists that you created with the computer application (MusicSphere) are displayed in abbreviated form. Operations using special buttons Selecting a repeat play range to cycle between the following: 1 Press 6/ ! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list ! When the control mode is set to CTRL iPod, the repeat play range will be same as what is set for the connected iPod. Selecting a random play range (shuffle) to cycle between the following: 1 Press 5/ ! SNG – Play back songs in the selected list in random order. ! ALB – Play back songs from a randomly selected album in order. ! OFF – Not play back in random order. Playing all songs in random order (shuffle all) to turn shuffle all on. 1 Press and hold 5/ ! To turn off shuffle all, select OFF in shuffle. For details, refer to Selecting a random play range (shuffle) on page 6. Pausing playback 1 Press 4/PAUSE to pause or resume. Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 3/S.Rtrv to cycle between: 1—2—OFF (off) 1 is effective for low compression rates, and 2 is effective for high compression rates. Playing songs related to the currently playing song You can play songs from the following lists. • Album list of the currently playing artist • Song list of the currently playing album • Album list of the currently playing genre 1 Press and hold mode. to switch to link play 2 Turn M.C. to change the mode; press to select. ! ARTIST – Plays an album by the artist currently playing. ! ALBUM – Plays a song from the album currently being played. ! GENRE – Plays an album from the genre currently being played. The selected song/album will be played after the currently playing song. Notes ! The selected song/album may be canceled if you use functions other than link search (e.g. fast forward and reverse). ! Depending on the song selected to play, the end of the currently playing song and the beginning of the selected song/album may be cut off. Using this unit’s iPod function from your iPod This unit’s iPod function can be controlled by using the connected iPod. CTRL iPod is not compatible with the following iPod models. ! iPod nano 1st generation ! iPod with video % Press BAND/ mode. to switch the control ! CTRL iPod – This unit’s iPod function can be operated from the connected iPod. 6 En <QRD3247-B> 6 Black plate (7,1) Section Using this unit You can also switch the control mode by pressing iPod. Notes ! Switching the control mode to CTRL iPod pauses song playback. Use the iPod to resume playback. ! The following operations are still accessible from the unit even if the control mode is set to CTRL iPod. — Pausing — Fast forward/reverse — Selecting a song (chapter) S.RTRV (sound retriever) 1 Press M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on page 6. Using connected device applications You can use this unit to perform streaming playback of and control tracks in iPhone applications or just for streaming playback. ! The volume can only be adjusted from this unit. Function settings 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. Once selected, the following functions can be adjusted. ! AUDIO BOOK is not available when CTRL iPod is selected in the control mode. For details, refer to Using this unit’s iPod function from your iPod on page 6. AUDIO BOOK (audiobook speed) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting. ! FASTER – Playback at a speed faster than normal ! NORMAL – Playback at normal speed ! SLOWER – Playback at a speed slower than normal For iPhone users ! This function is compatible with iPhone and iPod touch. ! The device has iOS 5.0 or higher. Notes ! Please check our website for a list of supported iPhone applications for this unit. ! Pioneer is not liable for any issues that may arise from incorrect or flawed app-based content. ! The content and functionality of the supported applications are the responsibility of the App providers. Starting procedure for iPhone users Important Use of third party apps may involve or require the provision of personally identifiable information, whether through the creation of a user account or otherwise, and for certain applications, the provision of geolocation data. ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO NOT USE THAT THIRD PARTY APP. Information for compatibility of connected devices The following is the detailed information regarding the terminals required to use the application for iPhone on this unit. 1 Connect an iPhone to USB input. 2 Switch the source to APP. 3 Start up the application on the iPhone and initiate playback. Basic operations Selecting a track 1 Press c or d. Fast forwarding or reversing 1 Press and hold c or d. Pausing playback 1 Press BAND/ to pause or resume. Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: ! TRACK INFO (track title/artist name/album title) ! APP NAME (application name) ! ELAPSED TIME (playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) 02 Function settings 1 English ! CTRL AUDIO – This unit’s iPod function can be controlled by using this unit. Using this unit Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. Once selected, the following functions can be adjusted. PAUSE (pause) 1 Press M.C. to pause or resume. S.RTRV (sound retriever) 1 Press M.C. to select the desired setting. 1—2—OFF (off) 1 is effective for low compression rates, and 2 is effective for high compression rates. Audio adjustments 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select AUDIO. 3 Turn M.C. to select the audio function. Once selected, the following audio functions can be adjusted. ! FADER is not available when SUB.W/SUB.W is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout setting) on page 9. ! SUB.W and SUB.W CTRL are not available when REAR/REAR is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout setting) on page 9. ! SUB.W CTRL is not available when SUB.W is selected in OFF. For details, refer to SUB.W (subwoofer on/off setting) on page 8. En <QRD3247-B> 7 7 Black plate (8,1) Section Using this unit 02 ! SLA is not available when FM is selected as the source. FADER (fader adjustment) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the front/rear speaker balance. BALANCE (balance adjustment) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the left/right speaker balance. EQ SETTING (equalizer recall) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS The equalizer band and equalizer level can be customized when CUSTOM1 or CUSTOM2 is selected. If selecting CUSTOM1 or CUSTOM2, complete the procedures outlined below. If selecting other options, press M.C. to return to the previous display. ! CUSTOM1 can be set separately for each source. However, USB, iPod and APP are all set to the same setting automatically. ! CUSTOM2 is a shared setting used in common for all sources. 3 Press M.C. to display the setting mode. 4 Press M.C. to cycle between the following: Equalizer band—Equalizer level 5 Turn M.C. to select the desired setting. Equalizer band: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizer level: +6 to –6 Using this unit Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume. 1 Press M.C. to select the desired setting. OFF (off)—LOW (low)—MID (mid)—HI (high) SUB.W (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to select the desired setting. NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off) SUB.W CTRL (subwoofer adjustment) Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following: Cut-off frequency—Output level—Slope level Rates that can be adjusted will flash. 3 Turn M.C. to select the desired setting. Cut-off frequency: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Output level: –24 to +6 Slope level: –12— –24 Use this function when wanting to listen only to high-frequency sounds. Only frequencies higher than the high-pass filter (HPF) cutoff are output from the speakers. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following: Cut-off frequency—Slope level 3 Turn M.C. to select the desired setting. Cut-off frequency: OFF—50HZ—63HZ—80HZ —100HZ—125HZ—160HZ—200HZ Slope level: –12— –24 SLA (source level adjustment) This function prevents the volume from changing too dramatically when the source switches. ! Settings are based on the FM volume level, which remains unchanged. ! The MW/LW volume level can also be adjusted with this function. ! USB, iPod and APP are all set to the same setting automatically. 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume. Adjustment range: +4 to –4 BASS BOOST (bass boost) System menu 1 Press M.C. to display the setting mode. 2 Turn M.C. to select a desired level. 0 to +6 is displayed as the level is increased or decreased. Important PW SAVE (power saving) is canceled if the vehicle battery is disconnected and will need to be turned back on once the battery is reconnected. When PW SAVE (power saving) is off, depending on connection methods, the unit may continue to draw power from the battery if your vehicle’s ignition doesn’t have an ACC (accessory) position. HPF SETTING (high pass filter adjustment) 1 Press M.C. to display the main menu. LOUDNESS (loudness) 3 Turn M.C. to select the system menu function. Once selected, the following system menu functions can be adjusted. LANGUAGE (multi-language) 1 Press M.C. to select the desired setting. ENG (English)—РУС (Russian)—TUR (Turkish) CLOCK SET (setting the clock) 1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock display you wish to set. Hour—Minute 3 Turn M.C. to adjust the clock. 12H/24H (time notation) 1 Press M.C. to select the desired setting. 12H (12-hour clock)—24H (24-hour clock) AUTO PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. AUX (auxiliary input) Activate this setting when using an auxiliary device connected to this unit. 1 Press M.C. to turn AUX on or off. DIMMER (dimmer) 1 Press M.C. to turn the dimmer on or off. ! You can also change the dimmer setting by pressing and holding /DIMMER. MUTE MODE (mute mode) 2 Turn M.C. to change the menu option and press to select SYSTEM. 8 En <QRD3247-B> 8 Black plate (9,1) Section Using this unit PW SAVE (power saving) Switching this function on enables you to reduce the consumption of battery power. ! Turning on the source is the only operation allowed when this function is on. 1 Press M.C. to turn the power save on or off. Initial menu 1 Press and hold SRC/OFF until the unit turns off. 2 Press and hold SRC/OFF until the main menu appears in the display. 3 Turn M.C. to change the menu option and press to select INITIAL. 4 Turn M.C. to select the initial menu function. Once selected, the following initial menu functions can be adjusted. FM STEP (FM tuning step) 1 Press M.C. to select the FM tuning step. 100 (100 kHz)—50 (50 kHz) SP-P/O MODE (rear output and preout setting) The rear speaker leads output and the RCA output of this unit can be used to connect a full-range speaker or subwoofer. Select a suitable option for your connection. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. ! REAR/SUB.W – Select when there is a fullrange speaker connected to the rear speaker leads output and there is a subwoofer connected to the RCA output. ! SUB.W/SUB.W – Select when there is a subwoofer connected directly to the rear speaker leads output without any auxiliary amp and there is a subwoofer connected to the RCA output. ! REAR/REAR – Select when there is a fullrange speaker connected to the rear speaker leads output and the RCA output. If there is a full-range speaker connected to the rear speaker leads output and the RCA output is not used, you may select either REAR/SUB.W or REAR/REAR. 2 Press SRC/OFF to select AUX as the source. Note AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on page 8. Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: ! Source name ! Source name and clock If an unwanted display appears Turn off the unwanted display using the procedures listed below. 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select SYSTEM. System menu 3 Turn M.C. to display DEMO OFF and press to select. 1 Press and hold SRC/OFF until the unit turns off. 4 Turn M.C. to switch to YES. 5 Press M.C. to select. 2 Press and hold SRC/OFF until the main menu appears in the display. 02 English Sound from this system is automatically muted or attenuated when a signal from equipment with a mute function is received. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. ! MUTE – Muting ! 20dB ATT – Attenuation (20dB ATT has a stronger effect than 10dB ATT) ! 10dB ATT – Attenuation Using this unit 3 Turn M.C. to change the menu option and press to select SYSTEM. 4 Turn M.C. to select the system menu function. For details, refer to System menu on page 8. Using an AUX source 1 Insert the stereo mini plug into the AUX input jack. En <QRD3247-B> 9 9 Black plate (10,1) Section Installation 03 Installation — Never wire the negative speaker cable directly to ground. — Never band together negative cables of multiple speakers. Connections F O N OF Important ! When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain. STAR T ACC position No ACC position ! Use of this unit in conditions other than the following could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 W to 8 W (impedance value). ! To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below. — Disconnect the negative terminal of the battery before installation. — Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring. — Place all cables away from moving parts, such as the shift lever and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited. — Use a fuse of the rating prescribed. 10 ! When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. ! Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction. ! The black cable is ground. Ground cables for this unit and other equipment (especially, high-current products such as power amps) must be wired separately. If they are not, an accidental detachment may result in a fire or malfunction. This unit 1 1 2 3 4 23 4 5 Antenna input Fuse (10 A) Power cord input Wired remote input Hard-wired remote control adapter can be connected (sold separately). 5 Rear output or subwoofer output Power cord 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d 1 To power cord input 2 Depending on the kind of vehicle, the function of 3 and 5 may be different. In this case, be sure to connect 4 to 5 and 6 to 3. 3 Yellow Back-up (or accessory) 4 Yellow Connect to the constant 12 V supply terminal. 5 Red Accessory (or back-up) 6 Red Connect to terminal controlled by ignition switch (12 V DC). 7 Connect leads of the same color to each other. 8 Black (chassis ground) 9 Blue/white The pin position of the ISO connector will differ depending on the type of vehicle. Connect 9 and b when Pin 5 is an antenna control type. In another type of vehicle, never connect 9 and b. a Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). b Blue/white Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). c Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. d Speaker leads White: Front left + White/black: Front left * Gray: Front right + Gray/black: Front right * Green: Rear left + or subwoofer + Green/black: Rear left * or subwoofer * Violet: Rear right + or subwoofer + Violet/black: Rear right * or subwoofer * e ISO connector In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. Notes ! Change the initial menu of this unit. Refer to SP-P/O MODE (rear output and preout setting) on page 9. The subwoofer output of this unit is monaural. ! When using a subwoofer of 70 W (2 W), be sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads. En <QRD3247-B> 10 Black plate (11,1) Section Installation Installation Power amp (sold separately) 3 1 5 2     ! When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents. 2 Insert the supplied extraction keys into both sides of the unit until they click into place. 1 English Perform these connections when using the optional amplifier. 03 4 5 1 System remote control Connect to Blue/white cable. 2 Power amp (sold separately) 3 Connect with RCA cables (sold separately) 4 To Rear output or subwoofer output 5 Rear speaker or subwoofer Leave ample 5 cm space 5 cm 2 5cm cm 3 Pull the unit out of the holder. Remove the holder. 1 Dashboard 2 Holder (factory-supplied part) 1 ! Use commercially available parts when installing. 2 Install this unit. Installation Important ! Check all connections and systems before final installation. ! Do not use unauthorized parts as this may cause malfunctions. ! Consult your dealer if installation requires drilling of holes or other modifications to the vehicle. ! Do not install this unit where: — it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result of a sudden stop. How to install This unit can be installed properly using either of the methods in the below list. ! Installation with the holder ! Installation using the screw holes on the side of the unit Before installing this unit 1 Remove the trim ring. 1 Holder (factory-supplied part) Installation with the holder 1 1 Dashboard 1 Install the holder into the dashboard. After inserting the holder into the dashboard, select and bend the tabs appropriate to the thickness of the dashboard material. (Install this unit as firmly as possible using the top and bottom tabs. To secure this unit, bend the tabs 90 degrees.) ! The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. ! Optimum performance is obtained when the unit is installed at an angle of less than 60°. 60° 1 1 Trim ring En <QRD3247-B> 11 11 Black plate (12,1) Section Installation 03 3 Additional information Attach the trim ring. 1 2 Troubleshooting Symptoms are written in bold and causes in regular, non-indented text. Regular, indented text is used to indicate actions to be taken. The display automatically returns to the ordinary display. You did not perform any operation within about 30 seconds. Perform operation again. 3 1 1 Trim ring Removing the holder The procedure is the same as that for Before installing this unit. For details, refer to Before installing this unit on page 11. Installation using the screw holes on the side of the unit % Fastening the unit to the factory radiomounting bracket. Position the unit so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at three locations on each side. 4 1 2 3 4 If the pawl gets in the way, bend it down. Factory radio mounting bracket Truss (5 mm × 8 mm) screws Dashboard or console The repeat play range changes unexpectedly. Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing. Select the repeat play range again. Error messages are written in bold and causes in regular, non-indented text. Regular, indented text is used to indicate actions to be taken. Common AMP ERROR This unit fails to operate or the speaker connection is incorrect; the protective circuit is activated. Check the speaker connection. If the message fails to disappear even after the engine is switched off/on, contact your dealer or an authorized Pioneer Service Station for assistance. CD player ERROR-07, 11, 12, 17, 30 A subfolder is not played back. Subfolders cannot be played when FLD (folder repeat) is selected. Select another repeat play range. NO XXXX appears when a display is changed (NO TITLE, for example). There is no embedded text information. Switch the display or play another track/file. The unit is malfunctioning. There is interference. You are using a device, such as a cellular phone, that may cause audible interference. Move electrical devices that may be causing the interference away from the unit. Error messages The disc is dirty. Clean the disc. The disc is scratched. Replace the disc. ERROR-07, 10, 11, 12, 15, 17, 30, A0 There is an electrical or mechanical error. Turn the ignition switch OFF and back ON, or switch to a different source, then back to the CD player. ERROR-15 The inserted disc is blank. Replace the disc. ERROR-23 Unsupported CD format. Replace the disc. When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message. 12 En <QRD3247-B> 12 Black plate (13,1) Appendix Additional information Additional information PROTECT Sometimes there is a delay between the start of playback and when you start to hear any sound. Wait until the message disappears and you hear sound. All the files on the connected USB storage device are embedded with DRM. Replace the USB storage device. iPod failure. Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it. N/A USB ERROR-23 The connected USB device is not supported by this unit. ! Connect a USB Mass Storage Class compliant device. ! Disconnect your device and replace it with a compatible USB storage device. USB storage device was not formatted with FAT12, FAT16 or FAT32. USB storage device should be formatted with FAT12, FAT16 or FAT32. NO AUDIO The inserted disc does not contain any playable files. Replace the disc. SKIPPED The inserted disc contains DRM protected files. The protected files are skipped. PROTECT All the files on the inserted disc are embedded with DRM. Replace the disc. USB storage device/iPod FORMAT READ Sometimes there is a delay between the start of playback and when you start to hear any sound. Wait until the message disappears and you hear sound. There are no songs. Transfer the audio files to the USB storage device and connect. CHECK USB The iPod firmware version is old. Update the iPod version. The USB connector or USB cable has shortcircuited. Check that the USB connector or USB cable is not caught in something or damaged. iPod failure. Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it. CHECK USB STOP The connected USB storage device consumes more than maximum allowable current. Disconnect the USB storage device and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices. There are no songs in the current list. Select a list that contains songs. The connected USB storage device has security enabled. Follow the USB storage device instructions to disable the security. SKIPPED The connected USB storage device contains DRM protected files. The protected files are skipped. The iPod operates correctly but does not charge. Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON, or disconnect the iPod and reconnect. ERROR-19 Communication failed. Perform one of the following operations. –Turn the ignition switch OFF and back ON. –Disconnect the USB storage device. –Change to a different source. Then, return to the USB source. Discs and player Use only discs that feature either of the following two logos. ERROR-16 Use 12-cm discs. Use only conventional, fully circular discs. The following types of discs cannot be used with this unit: ! DualDiscs ! 8-cm discs: Attempts to use such discs with an adapter may cause the unit to malfunction. ! Oddly shaped discs NOT FOUND No related songs. Transfer songs to the iPod. CHECK USB NO AUDIO Handling guidelines English FORMAT READ Application ! Discs other than CDs ! Damaged discs, including discs that are cracked, chipped or warped ! CD-R/RW discs that have not been finalized Do not touch the recorded surface of the discs. START UP APP Store discs in their cases when not in use. The application has not started running yet. Follow the instructions that appear on the screen. Do not attach labels, write on or apply chemicals to the surface of the discs. To clean a CD, wipe the disc with a soft cloth outward from the center. Condensation may temporarily impair the player’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth. En <QRD3247-B> 13 13 Black plate (14,1) Appendix Additional information Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on. Road shocks may interrupt disc playback. When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment. Do not attach commercially available labels or other materials to the discs. ! The discs may warp making the disc unplayable. ! The labels may come off during playback and prevent ejection of the discs, which may result in damage to the equipment. Additional information iPod Do not leave the iPod in places with high temperatures. Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal. About iPod settings ! When an iPod is connected, this unit changes the EQ (equalizer) setting of the iPod to off in order to optimize the acoustics. When you disconnect the iPod, the EQ returns to the original setting. ! You cannot set Repeat to off on the iPod when using this unit. Repeat is automatically changed to All when the iPod is connected to this unit. Incompatible text saved on the iPod will not be displayed by the unit. USB storage device Connections via USB hub are not supported. Do not connect anything other than a USB storage device. Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal. Depending on the USB storage device, the following problems may occur. ! Operations may vary. ! The storage device may not be recognized. ! Files may not be played back properly. ! The device may cause audible interference when you are listening to the radio. Compressed audio compatibility (disc, USB) WMA File extension: .wma Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR) Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatible MP3 File extension: .mp3 Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz, 48 kHz for emphasis) Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1.x.) Disc Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.) Playable folders: up to 99 M3u playlist: Not compatible Playable files: up to 999 MP3i (MP3 interactive), mp3 PRO: Not compatible File system: ISO 9660 Level 1 and 2, Romeo, Joliet Multi-session playback: Compatible WAV File extension: .wav Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM) Sampling frequency: 16 kHz to 48 kHz (LPCM), 22.05 kHz and 44.1 kHz (MS ADPCM) ! You cannot use this function with USB MTP. Supplemental information Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name. Russian text to be displayed on this unit should be encoded in one of the following character sets: ! Unicode (UTF-8, UTF-16) ! A character set other than Unicode that is used in a Windows environment and is set to Russian in the multi-language setting This unit may not work properly depending on the application used to encode WMA files. There may be a slight delay at the start of playback of audio files embedded with image data or audio files stored on a USB storage device that has numerous folder hierarchies. Packet write data transfer: Not compatible Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause between songs. USB storage device Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.) Playable folders: up to 500 Playable files: up to 15 000 Playback of copyright-protected files: Not compatible Partitioned USB storage device: Only the first partition can be played. There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies. CAUTION ! Pioneer cannot guarantee compatibility with all USB mass storage devices and assumes no responsibility for any loss of data on media players, smart phones, or other devices while using this product. Bit rate: 8 kbps to 320 kbps (CBR), VBR 14 En <QRD3247-B> 14 Black plate (15,1) Appendix Additional information About the file/format compatibility, refer to the iPod manuals. Audiobook, Podcast: Compatible iPod compatibility This unit supports only the following iPod models. Made for ! iPod touch (5th generation) ! iPod touch (4th generation) ! iPod touch (3rd generation) ! iPod touch (2nd generation) ! iPod touch (1st generation) ! iPod classic ! iPod with video ! iPod nano (7th generation) ! iPod nano (6th generation) ! iPod nano (5th generation) ! iPod nano (4th generation) ! iPod nano (3rd generation) ! iPod nano (2nd generation) ! iPod nano (1st generation) ! iPhone 5 ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone Depending on the generation or version of the iPod, some functions may not be available. Operations may vary depending on the software version of iPod. Users of iPod with the Lightning Connector should use the Lightning to USB Cable (supplied with iPod). Users of iPod with the Dock Connector should use CD-IU51. For details, consult your dealer. CAUTION Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used. Sequence of audio files The user cannot assign folder numbers and specify playback sequences with this unit. Example of a hierarchy 01 02   03   04   05 Level 1 Level 2 Level 3 Level 4 : Folder : Compressed audio file 01 to 05: Folder number 1 to 6: Playback sequence 3 Save the folder containing files on the USB storage device. However, depending on the system environment, you may not be able to specify the playback sequence. For USB portable audio players, the sequence is different and depends on the player. Russian character chart WMA Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc. English ! Do not leave discs or a USB storage device in any place that is subject to high temperatures. Additional information iPod & iPhone D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я D: Display C: Character Copyright and trademark iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Androidä Android is a trademark of Google Inc. MP3 Disc Folder selection sequence or other operation may differ depending on the encoding or writing software. USB storage device Playback sequence is the same as recorded sequence in the USB storage device. To specify the playback sequence, the following method is recommended. 1 Create a file name that includes numbers that specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3). 2 Put those files into a folder. Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/ streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com. En <QRD3247-B> 15 15 Black plate (16,1) Appendix Additional information Specifications General Power source ................... 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............ Negative type Maximum current consumption ................................... 10.0 A Dimensions (W × H × D): DIN Chassis ............................ 178 mm × 100 mm × 157 mm Nose ................................ 188 mm × 118 mm × 25 mm D Chassis ............................ 178 mm × 100 mm × 165 mm Nose ................................ 170 mm × 96 mm × 17 mm Weight ............................. 1.2 kg Audio Maximum power output ... 50 W × 4 70 W × 1/2 W (for subwoofer) Continuous power output ................................... 22 W × 4 (50 Hz to 15 000 Hz, 5 % THD, 4 W load, both channels driven) Load impedance .............. 4 W (4 W to 8 W allowable) Preout maximum output level ................................... 2.0 V Loudness contour ............ +10 dB (100 Hz), +6.5 dB (10 kHz) (volume: –30 dB) Equalizer (5-Band Graphic Equalizer): Frequency ........................ 80 Hz/250 Hz/800 Hz/2.5 kHz/ 8 kHz Equalization range ........... ±12 dB (2 dB step) Subwoofer (mono): Frequency ........................ 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Slope ............................... –12 dB/oct, –24 dB/oct Gain ................................ +6 dB to –24 dB Phase .............................. Normal/Reverse CD player System ............................ Usable discs .................... Signal-to-noise ratio ......... Number of channels ........ MP3 decoding format ...... 16 WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) USB USB standard specification ................................... USB 2.0 full speed Maximum current supply ................................... 1 A USB Class ....................... MSC (Mass Storage Class) File system ....................... FAT12, FAT16, FAT32 MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3 WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) FM tuner Frequency range .............. 87.5 MHz to 108.0 MHz Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N: 30 dB) Signal-to-noise ratio ......... 72 dB (IEC-A network) MW tuner Frequency range .............. 531 kHz to 1 602 kHz Usable sensitivity ............. 25 µV (S/N: 20 dB) Signal-to-noise ratio ......... 62 dB (IEC-A network) LW tuner Frequency range .............. 153 kHz to 281 kHz Usable sensitivity ............. 28 µV (S/N: 20 dB) Signal-to-noise ratio ......... 62 dB (IEC-A network) Note Specifications and the design are subject to modifications without notice. Compact disc audio system Compact disc 94 dB (1 kHz) (IEC-A network) 2 (stereo) MPEG-1 & 2 Audio Layer 3 En <QRD3247-B> 16 Black plate (17,1) English En <QRD3247-B> 17 17 Black plate (18,1) Section Avant de commencer 01 Nous vous remercions d’avoir acheté cet appareil PIONEER Pour garantir une utilisation correcte, lisez bien ce mode d’emploi avant d’utiliser cet appareil. Il est particulièrement important que vous lisiez et respectiez les indications ATTENTION et PRÉCAUTION de ce mode d’emploi. Conservez-le dans un endroit sûr et facilement accessible pour toute consultation ultérieure. Avant de commencer Quelques mots sur cet appareil Les fréquences du syntoniseur de cet appareil sont attribuées pour une utilisation en Europe de l’Ouest, Asie, Moyen-Orient, Afrique et Océanie. Son utilisation dans d’autres régions peut se traduire par une réception de mauvaise qualité. La fonction RDS (radio data system) n’est opérationnelle que dans les régions où des signaux RDS sont diffusés pour les stations FM. ATTENTION Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures ménagères. Il existe un système de collecte séparé pour les appareils électroniques usagés, qui doivent être récupérés, traités et recyclés conformément à la législation. Dans les états membres de l’UE, en Suisse et en Norvège, les foyers domestiques peuvent rapporter leurs produits électroniques usagés gratuitement à des points de collecte spécifiés ou à un revendeur (sous réserve d’achat d’un produit similaire). Dans les pays qui ne sont pas mentionnés cidessus, veuillez contacter les autorités locales pour vous informer de la méthode correcte de mise au rebut. En agissant ainsi vous assurerez que le produit que vous mettez au rebut est soumis au processus de traitement, de récupération et de recyclage nécessaire et éviterez ainsi les effets négatifs potentiels sur l’environnement et la santé publique. 18 ! N’essayez pas d’installer cet appareil ou d’en faire l’entretien vous-même. L’installation ou l’entretien de cet appareil par des personnes sans formation et sans expérience en équipement électronique et en accessoires automobiles peut être dangereux et vous exposer à des risques d’électrocution ou à d’autres dangers. ! N’essayez pas de démonter ou de modifier cet appareil. Veillez à quitter la route et garer votre véhicule en lieu sûr avant d’essayer d’utiliser les commandes de l’appareil. PRÉCAUTION Cet appareil est un produit laser de Classe 1, classé selon l’article IEC 60825-1:2007 relatif à la Sécurité des produits laser. APPAREIL À LASER DE CLASSE 1 Si vous rencontrez des problèmes En cas d’anomalie, veuillez contacter votre revendeur ou le centre d’entretien agréé par PIONEER le plus proche. PRÉCAUTION ! Ne laissez pas cet appareil entrer en contact avec des liquides. Cela pourrait provoquer une électrocution. Tout contact avec des liquides pourrait également provoquer des dommages, de la fumée et une surchauffe de l’appareil. ! Le Pioneer CarStereo-Pass est utilisable seulement en Allemagne. ! Maintenez le niveau d’écoute à une valeur telle que vous puissiez entendre les sons provenant de l’extérieur. ! Évitez tout contact avec l’humidité. Fr <QRD3247-B> 18 Black plate (19,1) Section Utilisation de cet appareil Utilisation de cet appareil Appareil central 1 2 PRÉCAUTION 3 4 5 Indications affichées 2 1 6 7 1 h (éjection) 2 iPod 89 4 b 7 9 6 8 a b cd 3 1/ 4 Fente de chargement des disques 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d à 6/ a 1 (contrôle de l’iPod) b 2 3 Section d’informations secondaires 4 TA (bulletins d’informations routières) TP (identification des programmes d’informations routières) MULTI-CONTROL (M.C.) a (retour)/DIMMER (atténuateur de luminosité) 6 7 1 Après avoir installé l’appareil, mettez le contact d’allumage sur ON. SET UP s’affiche. (liste) (contrôle de l’iPod) La fonction iPod de cet appareil est utilisée à partir de votre iPod. 9 (liste) Apparaît lorsqu’un niveau inférieur de dossier ou de menu existe. Menu de configuration 5 b 3 5 a Section d’informations principales ! Syntoniseur : gamme et fréquence ! RDS : nom du service de programme, informations PTY et autres informations textuelles ! Lecteur de CD, périphérique de stockage USB et iPod : temps de lecture écoulé et informations textuelles (sound retriever) LOC (accord automatique sur une station locale) c Jack d’entrée AUX (jack stéréo 3,5 mm) 8 (répétition de la lecture) d Port USB 9 (lecture aléatoire) 2 Tournez M.C. pour passer à YES. # Si vous n’utilisez pas l’appareil dans les 30 secondes environ, le menu de configuration ne s’affichera pas. # Si vous préférez ne pas effectuer la configuration pour l’instant, tournez M.C. pour passer à NO. 3 Appuyez sur M.C. pour sélectionner. 4 Procédez comme suit pour définir le menu. Pour passer à la prochaine option de menu, vous devez confirmer votre sélection. LANGUAGE (multilingue) Cet appareil peut afficher les informations textuelles d’un fichier audio compressé même si elles sont incorporées en anglais, en russe ou en turc. ! Si la langue incorporée et la langue sélectionnée sont différentes, les informations textuelles peuvent ne pas s’afficher correctement. ! Certains caractères peuvent ne pas s’afficher correctement. 1 Tournez M.C. pour sélectionner le réglage souhaité. ENG (Anglais)—РУС (Russe)—TUR (Turc) 2 Appuyez sur M.C. pour confirmer la sélection. Français Utilisez un câble USB Pioneer optionnel (CDU50E) pour connecter le périphérique de stockage USB, faute de quoi ce dernier, comme n’importe quel périphérique relié directement à l’appareil, dépasserait de l’appareil et pourrait s’avérer dangereux. 02 CLOCK SET (réglage de l’horloge) 1 Tournez M.C. pour régler l’heure. 2 Appuyez sur M.C. pour sélectionner les minutes. 3 Tournez M.C. pour régler les minutes. 4 Appuyez sur M.C. pour confirmer la sélection. FM STEP (incrément d’accord FM) Utilisez FM STEP pour régler les options d’incrément d’accord FM (recherchez les réglages de l’incrément). 1 Tournez M.C. pour choisir l’incrément d’accord FM. 100 (100 kHz) — 50 (50 kHz) 2 Appuyez sur M.C. pour confirmer la sélection. QUIT s’affiche. ! L’incrément d’accord manuel est défini sur 50 kHz. ! Quand les fonctions AF et TA sont toutes deux désactivées, l’incrément d’accord est défini sur 50 kHz même s’il est réglé sur 100. 5 Pour terminer la configuration, tournez M.C. pour sélectionner YES. # Si vous souhaitez modifier à nouveau le réglage, tournez M.C. pour passer à NO. 6 Appuyez sur M.C. pour sélectionner. Fr <QRD3247-B> 19 19 Black plate (20,1) Section Utilisation de cet appareil 02 Remarques ! Vous pouvez configurer les options de menu à partir du menu système et du menu initial. Pour des détails sur les réglages, reportezvous à la page 26, Menu système et la page 26, Menu initial. ! Vous pouvez annuler le menu de configuration en appuyant sur SRC/OFF. Opérations de base Mise en service de l’appareil 1 Appuyez sur SRC/OFF pour mettre en service l’appareil. Mise hors service de l’appareil 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. Choix d’une source 1 Appuyez sur SRC/OFF pour parcourir les options disponibles : RADIO—CD—USB/iPod—APP (application)— AUX ! USB MTP apparaît lorsque la connexion MTP est en cours d’utilisation. ! Lorsqu’un iPod est connecté et qu’une source autre que iPod est sélectionnée, vous pouvez basculer sur iPod en appuyant sur iPod. Réglage du volume 1 Tournez M.C. pour régler le volume. Remarque Si le fil bleu/blanc de l’appareil est relié à la prise de commande du relais de l’antenne motorisée du véhicule, celle-ci se déploie lorsque la source est mise en service. Pour rétracter l’antenne, mettez la source hors service. 20 Utilisation de cet appareil Opérations de menu fréquemment utilisées Retour à l’affichage précédent Retour à la liste précédente (le dossier de niveau immédiatement supérieur) 1 Appuyez sur /DIMMER. Retour à l’affichage ordinaire Annulation du menu principal 1 Appuyez sur BAND/ . Retour à l’affichage ordinaire à partir de la liste 1 Appuyez sur BAND/ . Remarques ! Pour des détails sur SEEK, reportez-vous à la page 21, SEEK (réglage de la touche droite/ gauche). ! La fonction AF (recherche des autres fréquences possibles) de cet appareil peut être mise en service ou hors service. La fonction AF doit être hors service pendant une opération d’accord normal (reportez-vous à la page 21, AF (recherche des autres fréquences possibles)). Enregistrement et rappel des stations pour chaque gamme Utilisation des touches de présélection Radio Opérations de base Sélection d’une gamme 1 Appuyez sur BAND/ jusqu’à ce que la gamme désirée (FM1, FM2, FM3 en FM ou MW/LW (PO/GO)) s’affiche. Changement de fréquence en mémoire 1 Appuyez sur c ou d. ! Sélectionnez PCH (canal présélectionné) sous SEEK pour utiliser cette fonction. Accord manuel (pas à pas) 1 Appuyez sur c ou d. ! Sélectionnez MAN (accord manuel) sous SEEK pour utiliser cette fonction. Recherche 1 Appuyez de manière prolongée sur c ou d, puis relâchez. Vous pouvez annuler l’accord automatique en appuyant brièvement sur c ou d. Lorsque vous appuyez de manière prolongée sur c ou d, vous pouvez sauter des stations. L’accord automatique démarre dès que vous relâchez c ou d. 1 Pour la mise en mémoire : Appuyez de façon prolongée sur l’une des touches de présélection (1/ à 6/ ) jusqu’à ce que le numéro cesse de clignoter. 2 Pour le rappel : Appuyez sur une des touches de présélection (1/ à 6/ ). Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! FREQUENCY (nom du service de programme ou fréquence) ! BRDCST INFO (nom du service de programme/informations PTY) ! CLOCK (nom de la source et horloge) Remarques ! Si le nom du service de programme ne peut pas être acquis dans FREQUENCY, la fréquence d’émission s’affiche alors. Si le nom du service de programme est détecté, celuici s’affiche. ! En fonction de la gamme sélectionnée, les informations textuelles peuvent être différentes. ! Les informations textuelles pouvant être modifiées dépendent de la région. Utilisation des fonctions PTY Vous pouvez rechercher une station à l’aide de son code PTY (type de programme). Recherche d’une station RDS en utilisant le code PTY 1 Appuyez sur (liste). 2 Tournez M.C. pour sélectionner le type de programme. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Appuyez sur M.C. pour lancer la recherche. Cet appareil recherche une station qui diffuse ce type de programme. Quand une station est trouvée, son nom de service de programme est affiché. ! Appuyez à nouveau sur M.C. pour abandonner la recherche. ! Le type de l’émission captée peut différer de celui indiqué par le code PTY transmis. ! Si aucune station ne diffuse d’émission du type choisi, l’indication NOT FOUND s’affiche pendant environ deux secondes puis le syntoniseur s’accorde sur la fréquence d’origine. Liste des codes PTY Pour plus de détails sur la liste PTY, visitez le site suivant : http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Réglages des fonctions 1 Appuyez sur M.C. pour afficher le menu principal. Fr <QRD3247-B> 20 Black plate (21,1) Section Utilisation de cet appareil 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. # Si la gamme MW/LW (PO/GO) est sélectionnée, seuls BSM, LOCAL et SEEK sont disponibles. FM SETTING (réglages de qualité sonore FM) Le niveau de qualité sonore peut être réglé afin de correspondre aux conditions du signal d’émission de la gamme FM. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le réglage souhaité. ! STANDARD – Il s’agit du réglage standard. ! HI-FI – Il s’agit du réglage à utiliser pour donner la priorité à la qualité supérieure du son stéréo. ! STABLE – Il s’agit du réglage à utiliser pour donner la priorité au faible bruit du son monaural. LOCAL (accord automatique sur une station locale) L’accord automatique sur une station locale ne s’intéresse qu’aux stations de radio dont le signal reçu est suffisamment puissant pour garantir une réception de bonne qualité. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. FM : OFF—LV1—LV2—LV3—LV4 MW/LW (PO/GO) : OFF—LV1—LV2 La valeur la plus élevée permet la réception des seules stations très puissantes ; les autres valeurs autorisent la réception de stations moins puissantes. REGIONAL (stations régionales) Quand la fonction AF est utilisée, la fonction de recherche des stations régionales limite la sélection aux stations qui diffusent des programmes régionaux. 1 Appuyez sur M.C. pour mettre la fonction de recherche des stations régionales en service ou hors service. Connexion MTP Il est possible de connecter des périphériques Android compatibles MTP (utilisant le système d’exploitation Android 4.0 ou version supérieure) via une connexion MTP à l’aide de la source USB. Pour connecter un périphérique Android, utilisez le câble fourni avec l’appareil. Remarque Cette fonction n’est pas compatible avec WAV. Opérations de base TA (attente de bulletins d’informations routières) 1 Appuyez sur M.C. pour mettre en service ou hors service l’attente d’un bulletin d’informations routières. AF (recherche des autres fréquences possibles) 1 Appuyez sur M.C. pour mettre la fonction AF en service ou hors service. NEWS (interruption pour réception d’un bulletin d’informations) BSM (mémoire des meilleures stations) La fonction BSM (mémoire des meilleures stations) mémorise automatiquement les six stations les plus fortes dans l’ordre de la force du signal. 1 Appuyez sur M.C. pour mettre la fonction BSM en service. Pour annuler, appuyez à nouveau sur M.C. CD/CD-R/CD-RW et périphériques de stockage USB 1 Appuyez sur M.C. pour mettre la fonction NEWS (bulletin d’informations) en service ou hors service. SEEK (réglage de la touche droite/gauche) Vous pouvez assigner une fonction aux touches droite et gauche de l’appareil. Sélectionnez MAN (accord manuel) pour effectuer un accord de fréquence manuellement ou sélectionnez PCH (canaux présélectionnés) pour changer de canal présélectionné. 1 Appuyez sur M.C. pour sélectionner MAN ou PCH. Lecture d’un CD/CD-R/CD-RW 1 Introduisez un disque, l’étiquette vers le haut, dans le logement de chargement des disques. 02 Retour au dossier racine 1 Appuyez sur BAND/ de façon prolongée. Commutation entre les modes audio compressé et CD-DA 1 Appuyez sur BAND/ . Changement de périphérique de mémoire de lecture Vous pouvez basculer entre les périphériques de mémoire sur les périphériques de stockage USB ayant plus d’un périphérique de mémoire compatible avec la norme Mass Storage Class pour effectuer la lecture. 1 Appuyez sur BAND/ . ! Vous pouvez basculer entre 32 différents périphériques de mémoire maximum. Français 3 Tournez M.C. pour sélectionner la fonction. Une fois sélectionnées, les fonctions suivantes peuvent être ajustées. Utilisation de cet appareil Remarque Débranchez les périphériques de stockage USB de l’appareil lorsque vous ne l’utilisez pas. Éjection d’un CD/CD-R/CD-RW 1 Appuyez sur h. Lecture de plages musicales sur un périphérique de stockage USB 1 Ouvrez le capot du port USB. 2 Branchez le périphérique de stockage USB en utilisant un câble USB. Arrêt de la lecture de fichiers sur un périphérique de stockage USB 1 Vous pouvez débrancher le périphérique de stockage USB à tout moment. Sélection d’un dossier 1 Appuyez sur 1/ ou 2/ . Sélection d’une plage 1 Appuyez sur c ou d. Avance ou retour rapide 1 Appuyez de manière prolongée sur c ou d. ! Lors de la lecture d’un disque d’audio compressé, aucun son n’est émis pendant l’avance ou le retour rapide. Fr <QRD3247-B> 21 21 Black plate (22,1) Section Utilisation de cet appareil 02 Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : CD-DA ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) CD-TEXT ! TRACK INFO (titre de la plage/interprète de la plage/titre du disque) ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) MP3/WMA/WAV ! TRACK INFO (titre de la plage/nom de l’interprète/nom de l’album) ! FILE INFO (nom du fichier/nom du dossier) ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) Sélection et lecture des fichiers/ plages à partir de la liste des noms 1 Appuyez sur pour passer en mode liste des noms de fichiers/plages. 2 Utilisez M.C. pour sélectionner le nom de fichier (ou nom de dossier) souhaité. Sélection d’un fichier ou d’un dossier 1 Tournez M.C. Lecture 1 Lorsqu’un fichier ou une plage est sélectionné(e), appuyez sur M.C. 22 Utilisation de cet appareil Affichage d’une liste des fichiers (ou des dossiers) dans le dossier sélectionné 1 Quand un dossier est sélectionné, appuyez sur M.C. Lecture d’une plage musicale dans le dossier sélectionné 1 Quand un dossier est sélectionné, appuyez de manière prolongée sur M.C. Opérations à l’aide de touches spéciales Sélection d’une étendue de répétition de lecture pour parcourir les options 1 Appuyez sur 6/ disponibles : CD/CD-R/CD-RW ! ALL – Répétition de toutes les plages ! ONE – Répétition de la plage en cours de lecture ! FLD – Répétition du dossier en cours de lecture Périphérique de stockage USB ! ALL – Répétition de tous les fichiers ! ONE – Répétition du fichier en cours de lecture ! FLD – Répétition du dossier en cours de lecture Lecture des plages dans un ordre aléatoire pour activer ou désactiver 1 Appuyez sur 5/ la lecture aléatoire. Les plages d’une étendue de répétition sélectionnée sont lues dans un ordre aléatoire. ! Pour changer de plage musicale pendant une lecture aléatoire, appuyez sur d pour passer à la plage suivante. Appuyez sur c pour redémarrer la lecture de la plage en cours au début de la plage musicale. Pause de la lecture 1 Appuyez sur 4/PAUSE pour mettre en pause ou reprendre la lecture. Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)) 1 Appuyez sur 3/S.Rtrv pour parcourir les options disponibles : 1—2—OFF (hors service) 1 est efficace pour les faibles taux de compression et 2 est efficace pour les taux de compression élevés. Réglages des fonctions 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. Une fois sélectionnée, la fonction ci-dessous peut être ajustée. iPod Opérations de base Lecture de plages musicales sur un iPod 1 Ouvrez le capot du port USB. 2 Connectez un iPod à l’entrée USB. La lecture s’effectue automatiquement. Sélection d’une plage musicale (d’un chapitre) 1 Appuyez sur c ou d. Sélection d’un album 1 Appuyez sur 1/ ou 2/ . Avance ou retour rapide 1 Appuyez de manière prolongée sur c ou d. Remarques ! L’iPod ne peut pas être mis en service ou hors service lorsque le mode de commande est réglé sur CTRL AUDIO. ! Débranchez les écouteurs de l’iPod avant de le connecter à cet appareil. ! L’iPod sera mis hors service environ deux minutes après que le contact d’allumage est coupé. S.RTRV (sound retriever) Améliore automatiquement l’audio compressé et restaure un son riche. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. Pour les détails, reportez-vous à la page 22, Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)). Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! TRACK INFO (titre de la plage/nom de l’interprète/nom de l’album) ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) Recherche d’une plage musicale 1 Appuyez sur pour passer au menu principal de la recherche par liste. Fr <QRD3247-B> 22 Black plate (23,1) Section Utilisation de cet appareil 2 Utilisez M.C. pour sélectionner une catégorie/plage musicale. Lecture 1 Quand une plage musicale est sélectionnée, appuyez sur M.C. Affichage d’une liste des plages musicales dans la catégorie sélectionnée 1 Quand une catégorie est sélectionnée, appuyez sur M.C. Lecture d’une plage musicale dans la catégorie sélectionnée 1 Quand une catégorie est sélectionnée, appuyez sur M.C. de façon prolongée. Recherche par ordre alphabétique dans la liste 1 Lorsque la liste de la catégorie sélectionnée pour activer le mode s’affiche, appuyez sur de recherche par ordre alphabétique. ! Vous pouvez également passer en mode de recherche par ordre alphabétique en tournant M.C. deux fois. 2 Tournez M.C. pour sélectionner une lettre. 3 Appuyez sur M.C. pour afficher la liste alphabétique. ! Pour annuler la recherche, appuyez sur /DIMMER. Remarques ! Vous pouvez lire les listes de lecture créées à l’aide de l’application de l’ordinateur (MusicSphere). L’application sera disponible sur notre site web. ! Les listes de lecture créées à l’aide de l’application de l’ordinateur (MusicSphere) sont affichées sous forme abrégée. Opérations à l’aide de touches spéciales Sélection d’une étendue de répétition de lecture 1 Appuyez sur 6/ pour parcourir les options disponibles : ! ONE – Répétition de la plage musicale en cours de lecture ! ALL – Répétition de toutes les plages musicales de la liste sélectionnée ! Lorsque le mode de commande est défini sur CTRL iPod, l’étendue de répétition de lecture reste identique à celle définie pour l’iPod connecté. Sélection d’une plage de lecture aléatoire (shuffle) pour parcourir les options 1 Appuyez sur 5/ disponibles : ! SNG – Lecture des plages musicales dans un ordre aléatoire à l’intérieur de la liste sélectionnée. ! ALB – Lecture dans l’ordre de plages musicales à partir d’un album sélectionné au hasard. ! OFF – Pas de lecture dans un ordre aléatoire. Lecture de toutes les plages musicales dans un ordre aléatoire (lecture aléatoire de toutes les plages) pour 1 Appuyez de façon prolongée sur 5/ mettre en service la fonction de lecture aléatoire de toutes les plages. ! Pour mettre hors service la lecture aléatoire de toutes les plages, sélectionnez OFF pour la lecture aléatoire. Pour les détails, reportez-vous à la page 23, Sélection d’une plage de lecture aléatoire (shuffle). Pause de la lecture 1 Appuyez sur 4/PAUSE pour mettre en pause ou reprendre la lecture. Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)) 1 Appuyez sur 3/S.Rtrv pour parcourir les options disponibles : 1—2—OFF (hors service) 1 est efficace pour les faibles taux de compression et 2 est efficace pour les taux de compression élevés. Lecture de plages musicales liées à la plage musicale en cours de lecture Vous pouvez lire des plages musicales dans les listes suivantes. • Liste d’albums de l’interprète en cours de lecture • Liste de plages musicales de l’album en cours de lecture • Liste d’albums du genre en cours de lecture 1 Appuyez de façon prolongée sur activer le mode de lecture en liaison. pour 2 Tournez M.C. pour changer le mode, appuyez pour sélectionner. ! ARTIST – Lit un album de l’interprète en cours de lecture. ! ALBUM – Lit une plage musicale de l’album en cours de lecture. ! GENRE – Lit un album du genre en cours de lecture. La plage musicale/l’album sélectionné sera lu après la lecture de la plage musicale en cours. 02 Remarques ! La plage musicale/l’album sélectionné peut être annulé si vous utilisez d’autres fonctions que la fonction de recherche de liaison (retour rapide et avance rapide, par exemple). ! En fonction de la plage musicale sélectionnée pour la lecture, la fin de la plage en cours de lecture et le début de la plage musicale/de l’album sélectionné peuvent être tronqués. Français Modification du nom d’une plage musicale/catégorie 1 Tournez M.C. Listes de lecture—interprètes—albums—plages musicales—podcasts—genres—compositeurs—livres audio Utilisation de cet appareil Utilisation de la fonction iPod de cet appareil sur votre iPod La fonction iPod de cet appareil peut être contrôlée à l’aide de l’iPod connecté. CTRL iPod n’est pas compatible avec les modèles d’iPod suivants. ! iPod nano 1ère génération ! iPod avec vidéo % Appuyez sur BAND/ mode de commande. pour changer le ! CTRL iPod – La fonction iPod de cet appareil peut être utilisée à partir de l’iPod connecté. ! CTRL AUDIO – La fonction iPod de cet appareil peut être contrôlée à l’aide de cet appareil. Vous pouvez également changer le mode de commande en appuyant sur iPod. Remarques ! Régler le mode de commande sur CTRL iPod met en pause la lecture d’une plage musicale. Utilisez l’iPod pour reprendre la lecture. ! Les opérations suivantes sont toujours accessibles à partir de l’appareil même si le mode de commande est réglé sur CTRL iPod. — Pause — Avance/retour rapide — Sélection d’une plage musicale (d’un chapitre) Fr <QRD3247-B> 23 23 Black plate (24,1) Section Utilisation de cet appareil 02 Utilisation de cet appareil ! Le volume ne peut être réglé qu’à partir de cet appareil. Utilisation des applications de l’appareil connecté Réglages des fonctions Vous pouvez utiliser cet appareil pour la lecture en continu et le contrôle de plages d’applications iPhone ou simplement pour la lecture en continu. 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. 3 Tournez M.C. pour sélectionner la fonction. Une fois sélectionnées, les fonctions suivantes peuvent être ajustées. ! AUDIO BOOK n’est pas disponible lorsque CTRL iPod est sélectionné en mode de commande. Pour les détails, reportez-vous à la page 23, Utilisation de la fonction iPod de cet appareil sur votre iPod. AUDIO BOOK (vitesse du livre audio) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour choisir le réglage désiré. ! FASTER – Lecture plus rapide que la vitesse normale ! NORMAL – Lecture à la vitesse normale ! SLOWER – Lecture plus lente que la vitesse normale Important L’utilisation d’applications tierces peut impliquer ou nécessiter la fourniture d’informations personnelles, que ce soit en créant un compte d’utilisateur ou une autre méthode ainsi que, pour certaines applications, la fourniture de données de géolocalisation. TOUTES LES APPLICATIONS TIERCES RELÈVENT DE L’ENTIÈRE RESPONSABILITÉ DES FOURNISSEURS, NOTAMMENT MAIS SANS S’Y LIMITER, LA COLLECTE ET LA PROTECTION DES DONNÉES UTILISATEUR ET LES BONNES PRATIQUES DE CONFIDENTIALITÉ. EN ACCÉDANT À UNE APPLICATION TIERCE, VOUS ACCEPTEZ DE PRENDRE CONNAISSANCE DES CONDITIONS DE SERVICE ET DES RÈGLES DE CONFIDENTIALITÉ DES FOURNISSEURS. SI VOUS N’ACCEPTEZ PAS LES CONDITIONS OU RÈGLES D’UN FOURNISSEUR OU SI VOUS N’ACCEPTEZ PAS L’UTILISATION DES DONNÉES DE GÉOLOCALISATION, LE CAS ÉCHÉANT, N’UTILISEZ PAS CETTE APPLICATION TIERCE. S.RTRV (sound retriever) 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. Pour les détails, reportez-vous à la page 23, Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)). 24 Informations relatives à la compatibilité des appareils connectés Vous trouverez ci-dessous les informations détaillées relatives aux bornes nécessaires pour utiliser l’application pour iPhone sur cet appareil. Pour les utilisateurs d’iPhone ! Cette fonction est compatible avec iPhone et iPod touch. ! iOS 5.0 ou supérieure est installé sur l’appareil. Remarques ! Veuillez consulter notre site Web pour obtenir la liste des applications iPhone prises en charge pour cet appareil. ! Pioneer ne pourra être tenu responsable des problèmes résultant d’un contenu incorrect ou reposant sur une mauvaise application. ! Le contenu et les fonctionnalités des applications prises en charge sont de la responsabilité des fournisseurs de l’application. Procédure de démarrage des utilisateurs d’un iPhone 1 Connectez un iPhone à l’entrée USB. 2 Basculez la source sur APP. 3 Démarrez l’application sur l’iPhone et lancez la lecture. Opérations de base Sélection d’une plage 1 Appuyez sur c ou d. Avance ou retour rapide 1 Appuyez de manière prolongée sur c ou d. Pause de la lecture 1 Appuyez sur BAND/ pour mettre en pause ou reprendre la lecture. Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! TRACK INFO (titre de la plage/nom de l’interprète/nom de l’album) ! APP NAME (nom de l’application) ! ELAPSED TIME (temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) Réglages des fonctions 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. 3 Tournez M.C. pour sélectionner la fonction. Une fois sélectionnées, les fonctions suivantes peuvent être ajustées. PAUSE (pause) 1 Appuyez sur M.C. pour mettre en pause ou reprendre la lecture. S.RTRV (sound retriever) 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. 1—2—OFF (hors service) 1 est efficace pour les faibles taux de compression et 2 est efficace pour les taux de compression élevés. Fr <QRD3247-B> 24 Black plate (25,1) Section Utilisation de cet appareil Réglages sonores 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner AUDIO. ! FADER n’est pas disponible lorsque SUB.W/SUB.W est sélectionné dans SP-P/O MODE. Pour les détails, reportez-vous à la page 26, SP-P/O MODE (réglage de la sortie arrière et du préamp). ! SUB.W et SUB.W CTRL ne sont pas disponibles lorsque REAR/REAR est sélectionné dans SP-P/O MODE. Pour les détails, reportez-vous à la page 26, SP-P/O MODE (réglage de la sortie arrière et du préamp). ! SUB.W CTRL n’est pas disponible lorsque SUB.W est sélectionné dans OFF. Pour les détails, reportez-vous à la page 25, SUB.W (réglage en service/hors service du haut-parleur d’extrêmes graves). ! SLA n’est pas disponible lorsque FM est sélectionné comme source. FADER (réglage de l’équilibre avant-arrière) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler l’équilibre sonore entre les haut-parleurs avant et arrière. BALANCE (réglage d’équilibre sonore) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler l’équilibre sonore entre les haut-parleurs gauche/droite. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner l’égaliseur. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La bande et le niveau de l’égalisateur peuvent être personnalisés lorsque CUSTOM1 ou CUSTOM2 est sélectionné. Si CUSTOM1 ou CUSTOM2 est sélectionné, suivez les procédures décrites ci-dessous. Si d’autres options sont sélectionnées, appuyez sur M.C. pour revenir à l’affichage précédent. ! CUSTOM1 peut être défini séparément pour chaque source. Cependant, USB, iPod et APP sont définis automatiquement sur le même réglage. ! CUSTOM2 est un réglage partagé et commun à toutes les sources. 3 Appuyez sur M.C. pour afficher le mode de réglage. 4 Appuyez sur M.C. pour parcourir les options disponibles : Bande de l’égaliseur—Niveau de l’égaliseur 5 Tournez M.C. pour sélectionner le réglage souhaité. Bande de l’égaliseur : 80HZ—250HZ—800HZ —2.5KHZ—8KHZ Niveau de l’égaliseur : +6 à –6 LOUDNESS (correction physiologique) La correction physiologique a pour objet d’accentuer les hautes et les basses fréquences à bas niveaux d’écoute. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. OFF (hors service)—LOW (faible)—MID (moyen)—HI (élevé) Cet appareil est équipé d’une sortie haut-parleur d’extrêmes graves qui peut être mise en service ou hors service. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. NOR (phase normale) — REV (phase inversée) — OFF (haut-parleur d’extrêmes graves désactivé) SUB.W CTRL (réglage du haut-parleur d’extrêmes graves) Seules les fréquences inférieures à celles de la plage sélectionnée sont produites par le haut-parleur d’extrêmes graves. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour parcourir les options disponibles : Fréquence de coupure—Niveau de sortie—Niveau de pente Les débits pouvant être réglés clignotent. 3 Tournez M.C. pour sélectionner le réglage souhaité. Fréquence de coupure : 50HZ—63HZ—80HZ —100HZ—125HZ—160HZ—200HZ Niveau de sortie : –24 à +6 Niveau de pente : –12— –24 BASS BOOST (accentuation des graves) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le niveau désiré. 0 à +6 sont les valeurs affichées tandis que le niveau augmente ou diminue. 02 Utilisez cette fonction lorsque vous souhaitez uniquement écouter des sons aigus. Seules les fréquences supérieures à la coupure du filtre passehaut (HPF) sont émises en sortie via les haut-parleurs. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour parcourir les options disponibles : Fréquence de coupure—Niveau de pente 3 Tournez M.C. pour sélectionner le réglage souhaité. Fréquence de coupure : OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Niveau de pente : –12— –24 Français 3 Tournez M.C. pour sélectionner la fonction audio. Une fois sélectionnées, les fonctions audio suivantes peuvent être ajustées. Utilisation de cet appareil SLA (réglage du niveau de la source) Cette fonction empêche une modification trop importante du volume lors du basculement de source. ! Les réglages sont basés sur le niveau du volume FM qui lui, demeure inchangé. ! Le niveau du volume MW/LW (PO/GO) peut également être réglé avec cette fonction. ! USB, iPod et APP sont définis automatiquement sur le même réglage. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler le volume de la source. Plage de réglage : +4 à –4 HPF SETTING (réglage du filtre passe-haut) SUB.W (réglage en service/hors service du hautparleur d’extrêmes graves) EQ SETTING (rappel de l’égaliseur) Fr <QRD3247-B> 25 25 Black plate (26,1) Section Utilisation de cet appareil 02 Menu système Important La fonction PW SAVE (économie d’énergie) est annulée si la batterie du véhicule est déconnectée et devra être réactivée une fois la batterie reconnectée. Quand PW SAVE est hors service, il est possible que selon la méthode de connexion utilisée l’appareil continue à consommer du courant de la batterie si le commutateur de contact de votre véhicule ne possède pas de position ACC (accessoire). 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. 12H (horloge 12 heures)—24H (horloge 24 heures) AUTO PI (recherche automatique PI) L’appareil peut rechercher automatiquement une autre station avec le même type de programme, y compris si l’accord a été obtenu par le rappel d’une fréquence en mémoire. 1 Appuyez sur M.C. pour mettre en service ou hors service la recherche automatique PI. 1 Appuyez sur M.C. pour afficher le menu principal. AUX (entrée auxiliaire) 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. Activez ce réglage lorsque vous utilisez un appareil auxiliaire connecté à cet appareil. 1 Appuyez sur M.C. pour mettre AUX en service ou hors service. 3 Tournez M.C. pour sélectionner la fonction du menu système. Une fois sélectionnées, les fonctions du menu système suivantes peuvent être ajustées. LANGUAGE (multilingue) 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. ENG (Anglais)—РУС (Russe)—TUR (Turc) CLOCK SET (réglage de l’horloge) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour sélectionner le segment de l’affichage de l’horloge que vous souhaitez régler. Heure—Minute 3 Tournez M.C. pour régler l’horloge. 12H/24H (notation temporelle) 26 Utilisation de cet appareil DIMMER (atténuateur de luminosité) 1 Appuyez sur M.C. pour mettre l’atténuateur de luminosité en service ou hors service. ! Vous pouvez également changer le réglage de l’atténuateur de luminosité en appuyant de façon prolongée sur /DIMMER. PW SAVE (économie d’énergie) Activer cette fonction vous permet de réduire la consommation de la batterie. ! La mise en service de la source est la seule opération permise quand cette fonction est en service. 1 Appuyez sur M.C. pour mettre l’économie d’énergie en service ou hors service. Menu initial 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. 2 Appuyez de façon prolongée sur SRC/ OFF jusqu’à ce que le menu principal apparaisse sur l’afficheur. 3 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner INITIAL. 4 Tournez M.C. pour sélectionner la fonction du menu initial. Une fois sélectionnées, les fonctions du menu initial suivantes peuvent être ajustées. MUTE MODE (mode sourdine) Le son émis par l’appareil est automatiquement coupé ou atténué quand un signal en provenance d’un équipement possédant la fonction silencieux est reçu. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le réglage souhaité. ! MUTE – Silencieux ! 20dB ATT – Atténuation (20dB ATT a un effet plus fort que 10dB ATT) ! 10dB ATT – Atténuation FM STEP (incrément d’accord FM) 1 Appuyez sur M.C. pour choisir l’incrément d’accord FM. 100 (100 kHz) — 50 (50 kHz) SP-P/O MODE (réglage de la sortie arrière et du préamp) La sortie des bornes du haut-parleur arrière et la sortie RCA de cet appareil peuvent être utilisées pour connecter un haut-parleur pleine gamme ou un haut-parleur d’extrêmes graves. Sélectionnez l’option appropriée à votre connexion. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le réglage souhaité. ! REAR/SUB.W – Sélectionnez cette option lorsqu’un haut-parleur pleine gamme est connecté aux bornes du haut-parleur arrière et qu’un haut-parleur d’extrêmes graves est connecté à la sortie RCA. ! SUB.W/SUB.W – Sélectionnez cette option lorsqu’un haut-parleur d’extrêmes graves est connecté directement aux bornes du haut-parleur arrière sans amplificateur auxiliaire et qu’un haut-parleur d’extrêmes graves est connecté à la sortie RCA. ! REAR/REAR – Sélectionnez cette option lorsqu’un haut-parleur pleine gamme est connecté aux bornes du haut-parleur arrière et à la sortie RCA. Si un haut-parleur pleine gamme est connecté à la sortie des bornes du hautparleur arrière et que la sortie RCA n’est pas utilisée, vous pouvez sélectionner REAR/SUB.W ou REAR/REAR. Menu système 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. 2 Appuyez de façon prolongée sur SRC/ OFF jusqu’à ce que le menu principal apparaisse sur l’afficheur. Fr <QRD3247-B> 26 Black plate (27,1) Section Utilisation de cet appareil Installation 02 03 3 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. 3 Tournez M.C. pour afficher DEMO OFF, puis appuyez pour sélectionner. 4 Tournez M.C. pour sélectionner la fonction du menu système. Pour les détails, reportez-vous à la page 26, Menu système. 4 Tournez M.C. pour passer à YES. 5 Appuyez sur M.C. pour sélectionner. Important ! Lors de l’installation de cet appareil dans un véhicule sans position ACC (accessoire) sur le contact d’allumage, ne pas connecter le câble rouge à la borne qui détecte l’utilisation de la clé de contact peut entraîner le déchargement de la batterie. Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! Nom de la source ! Nom de la source et horloge Si un écran non souhaité s’affiche Mettez l’écran non souhaité hors service à l’aide des procédures répertoriées ci-dessous. 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. OF T Remarque Vous ne pouvez pas sélectionner AUX à moins que le réglage auxiliaire soit activé. Pour plus de détails, reportez-vous à la page 26, AUX (entrée auxiliaire). O Avec position ACC STAR 2 Appuyez sur SRC/OFF pour choisir AUX comme source. F N 1 Insérez la mini prise stéréo dans le jack d’entrée AUX. Sans position ACC ! L’utilisation de cet appareil dans des conditions autres que les conditions suivantes pourrait provoquer un incendie ou un mauvais fonctionnement. — Véhicules avec une batterie 12 volts et mise à la masse du négatif. — Haut-parleurs avec une puissance de sortie de 50 W et une impédance de 4 W à 8 W. ! Pour éviter un court-circuit, une surchauffe ou un dysfonctionnement, assurez-vous de respecter les instructions suivantes. — Déconnectez la borne négative de la batterie avant l’installation. — Fixez le câblage avec des serre-fils ou de la bande adhésive. Pour protéger le câblage, enroulez dans du ruban adhésif les parties du câblage en contact avec des pièces en métal. — Placez les câbles à l’écart de toutes les parties mobiles, telles que le levier de vitesse et les rails des sièges. — Placez les câbles à l’écart de tous les endroits chauds, par exemple les sorties de chauffage. — Ne reliez pas le câble jaune à la batterie à travers le trou dans le compartiment moteur. — Recouvrez tous les connecteurs de câbles qui ne sont pas connectés avec du ruban adhésif isolant. — Ne raccourcissez pas les câbles. — Ne coupez jamais l’isolation du câble d’alimentation de cet appareil pour partager l’alimentation avec d’autres appareils. La capacité en courant du câble est limitée. — Utilisez un fusible correspondant aux caractéristiques spécifiées. — Ne câblez jamais le câble négatif du haut-parleur directement à la masse. — Ne réunissez jamais ensemble les câbles négatifs de plusieurs haut-parleurs. ! Lorsque cet appareil est sous tension, les signaux de commande sont transmis via le câble bleu/blanc. Connectez ce câble à la télécommande du système d’un amplificateur de puissance externe ou à la borne de commande du relais de l’antenne motorisée du véhicule (max. 300 mA 12 V CC). Si le véhicule est équipé d’une antenne intégrée à la lunette arrière, connectez-le à la borne d’alimentation de l’amplificateur d’antenne. ! Ne reliez jamais le câble bleu/blanc à la borne d’alimentation d’un amplificateur de puissance externe. De même, ne le reliez pas à la borne d’alimentation de l’antenne motorisée. Dans le cas contraire, il peut en résulter un déchargement de la batterie ou un dysfonctionnement. ! Le câble noir est la masse. Les câbles de terre de cet appareil et d’autres produits (particulièrement les produits avec des courants élevés tels que l’amplificateur de puissance) doivent être câblés séparément. Dans le cas contraire, ils peuvent se détacher accidentellement et provoquer un incendie ou un dysfonctionnement. Fr <QRD3247-B> 27 Français Utilisation d’une source AUX Connexions 27 Black plate (28,1) Section Installation 03 Installation Cet appareil 1 23 4 5 1 2 3 4 Entrée antenne Fusible (10 A) Entrée cordon d’alimentation Entrée télécommande câblée Un adaptateur de télécommande câblée (vendu séparément) peut être connecté. 5 Sortie arrière ou haut-parleur d’extrêmes graves Cordon d’alimentation 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d 1 Vers l’entrée cordon d’alimentation 28 2 Selon le type de véhicule, 3 et 5 peuvent avoir une fonction différente. Dans ce cas, assurez-vous de connecter 4 à 5 et 6 à 3. 3 Jaune Alimentation de secours (ou accessoire) 4 Jaune Connectez à la borne d’alimentation 12 V permanente. 5 Rouge Accessoire (ou alimentation de secours) 6 Rouge Connectez à la borne contrôlée par le contact d’allumage (12 V CC). 7 Connectez les fils de même couleur ensemble. 8 Noir (masse du châssis) 9 Bleu/blanc La position des broches du connecteur ISO est différente selon le type de véhicule. Connectez 9 et b lorsque la broche 5 est de type commande de l’antenne. Dans un type différent de véhicule, ne connectez jamais 9 et b. a Bleu/blanc Connectez à la borne de commande du système de l’amplificateur de puissance (max. 300 mA 12 V CC). b Bleu/blanc Connectez à la borne de commande du relais de l’antenne motorisée (max. 300 mA 12 V CC). c Jaune/noir Si vous utilisez un équipement avec la fonction Coupure du son, câblez ce fil au fil Coupure Audio de cet équipement. Sinon, ne connectez rien au fil Coupure Audio. d Fils des haut-parleurs Blanc : Avant gauche + Blanc/noir : Avant gauche * Gris : Avant droite + Gris/noir : Avant droite * Vert : Arrière gauche + ou haut-parleur d’extrêmes graves + Vert/noir : Arrière gauche * ou haut-parleur d’extrêmes graves * Violet : Arrière droite + ou haut-parleur d’extrêmes graves + Violet/noir : Arrière droite * ou haut-parleur d’extrêmes graves * e Connecteur ISO Dans certains véhicules, il est possible que le connecteur ISO soit divisé en deux. Dans ce cas, assurez-vous de connecter les deux connecteurs. Remarques ! Changez le menu initial de cet appareil. Reportez-vous à la page 26, SP-P/O MODE (réglage de la sortie arrière et du préamp). La sortie haut-parleur d’extrêmes graves de cet appareil est monaurale. ! Lors de l’utilisation d’un haut-parleur d’extrêmes graves de 70 W (2 W), assurez-vous de connecter le haut-parleur d’extrêmes graves aux fils violet et violet/noir de cet appareil. Ne connectez aucun périphérique aux fils vert et vert/noir. Amplificateur de puissance (vendu séparément) 5 Haut-parleur arrière ou haut-parleur d’extrêmes graves Installation Important ! Vérifiez toutes les connexions et tous les systèmes avant l’installation finale. ! N’utilisez pas de pièces non autorisées car il peut en résulter des dysfonctionnements. ! Consultez votre revendeur si l’installation nécessite le perçage de trous ou d’autres modifications du véhicule. ! N’installez pas cet appareil là où : — il peut interférer avec l’utilisation du véhicule. — il peut blesser un passager en cas d’arrêt soudain du véhicule. ! Le laser à semi-conducteur sera endommagé s’il devient trop chaud. Installez cet appareil à l’écart de tous les endroits chauds, par exemple les sorties de chauffage. ! Des performances optimales sont obtenues quand l’appareil est installé à un angle inférieur à 60°. 60° Réalisez ces connexions lors de l’utilisation d’un amplificateur optionnel. 3 1 5 2     4 5 1 Télécommande du système Connectez au câble bleu/blanc. 2 Amplificateur de puissance (vendu séparément) 3 Connectez avec des câbles RCA (vendus séparément) 4 Vers la sortie arrière ou la sortie du haut-parleur d’extrêmes graves Fr <QRD3247-B> 28 Black plate (29,1) Section Installation Installation ! Lors de l’installation, pour assurer une dispersion correcte de la chaleur quand cet appareil est utilisé, assurez-vous de laisser un espace important derrière la face arrière et enroulez les câbles volants de façon qu’ils ne bloquent pas les orifices d’aération. 1 Anneau de garniture 1 Fixez l’anneau de garniture. Français 2 1 Tableau de bord 2 Support (pièce fournie) 5cm cm 3 Tirez l’appareil hors du support. Retirez le support. 1 ! Utilisez des pièces disponibles dans le commerce lors de l’installation. 2 Installez cet appareil. 1 Anneau de garniture La procédure est identique à la procédure Avant l’installation de cet appareil. Pour les détails, reportez-vous à la page 29, Avant l’installation de cet appareil. Cet appareil peut être installé correctement selon l’une des méthodes de la liste ci-dessous. ! Installation avec le support ! Installation à l’aide des trous de vis sur les côtés de l’appareil Avant l’installation de cet appareil 1 Retrait du support Procédure d’installation 1 3 2 Insérez les clés d’extraction fournies dans les deux côtés de l’appareil jusqu’à ce qu’elles s’enclenchent en place. Laissez suffisamment 5 cm d’espace 5 cm 03 1 1 Support (pièce fournie) Retirez l’anneau de garniture. Installation avec le support 1 Installez le support dans le tableau de bord. Une fois le support installé dans le tableau de bord, sélectionnez et courber les pattes en fonction de l’épaisseur du tableau de bord. (Fixez cet appareil aussi fermement que possible à l’aide des pattes supérieures et inférieures. Afin de fixer fermement l’appareil, courbez les pattes de 90 degrés.) 1 Tableau de bord Installation à l’aide des trous de vis sur les côtés de l’appareil % Fixation de l’appareil sur le support de montage radio d’usine. Positionnez l’appareil de sorte que les trous des vis soient alignés avec les trous des vis sur le support, puis serrez les vis aux trois emplacements de chaque côté de l’appareil. 1 Fr <QRD3247-B> 29 29 Black plate (30,1) Section Installation 03 Informations complémentaires 1 2 Dépannage Messages d’erreur Les symptômes apparaissent en gras et les causes sous la forme de texte régulier non indenté. Le texte régulier indenté est utilisé pour indiquer les actions à mettre en œuvre. Quand vous contactez votre distributeur ou le Service d’entretien agréé par Pioneer le plus proche, n’oubliez pas de noter le message d’erreur. Les message d’erreur apparaissent en gras et les causes sous la forme de texte régulier non indenté. Le texte régulier indenté est utilisé pour indiquer les actions à mettre en œuvre. L’écran revient automatiquement à l’affichage ordinaire. Vous n’avez exécuté aucune opération pendant 30 secondes. Réexécutez l’opération. 3 Commun AMP ERROR 4 1 2 3 4 Courbez la languette vers le bas si elle gêne. Support de montage radio d’usine Vis à tête bombée (5 mm × 8 mm) Tableau de bord ou console L’étendue de répétition de lecture change de manière inattendue. En fonction de l’étendue de répétition de lecture, l’étendue sélectionnée peut changer lors de la sélection d’un autre dossier ou d’une autre plage ou pendant l’avance ou le retour rapide. Resélectionnez l’étendue de répétition de lecture. Une anomalie de fonctionnement de l’appareil s’est produite ou la connexion des haut-parleurs est incorrecte. Le circuit de protection est activé. Vérifiez la connexion des haut-parleurs. Si le message ne disparaît pas même après avoir éteint puis démarré le moteur, consultez votre distributeur ou un centre d’entretien agréé par Pioneer. Un sous-dossier n’est pas lu. Il est impossible de lire les sous-dossiers lorsque FLD (répétition du dossier) est sélectionné. Sélectionnez une autre étendue de répétition de lecture. NO XXXX s’affiche lors de la modification de l’affichage (par exemple NO TITLE). Aucune information textuelle n’est intégrée. Basculez l’affichage ou la lecture sur une autre plage/un autre fichier. L’appareil ne fonctionne pas correctement. Il y a des interférences. Vous utilisez un périphérique, un téléphone portable par exemple, qui peut générer des interférences sonores. Éloignez tous les appareils électriques qui pourrait provoquer des interférences. 30 Lecteur de CD ERROR-07, 11, 12, 17, 30 Le disque est sale. Nettoyez le disque. Le disque est rayé. Utilisez un autre disque. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Une erreur mécanique ou électrique est survenue. Coupez et remettez le contact d’allumage ou choisissez une autre source, puis revenez au lecteur de CD. ERROR-15 Le disque inséré est vierge. Utilisez un autre disque. Fr <QRD3247-B> 30 Black plate (31,1) Annexe Informations complémentaires ERROR-23 Informations complémentaires CHECK USB NOT FOUND Aucune plage musicale connexe. Transférez les plages musicales sur l’iPod. Le périphérique de stockage USB connecté contient des fichiers protégés par DRM. Les fichiers protégés sont sautés. L’iPod fonctionne correctement mais n’est pas chargé. Assurez-vous que le câble de connexion de l’iPod n’est pas en court-circuit (par exemple, qu’il n’est pas coincé dans des objets métalliques). Après avoir vérifié, mettez le contact d’allumage sur OFF puis sur ON, ou déconnectez l’iPod et reconnectez-le. NO AUDIO PROTECT ERROR-19 Le disque inséré ne contient pas de fichiers pouvant être lus. Utilisez un autre disque. Tous les fichiers sur le périphérique de stockage USB connecté intègrent la protection par DRM. Remplacez le périphérique de stockage USB. SKIPPED N/A USB Le disque inséré contient des fichiers protégés par DRM. Les fichiers protégés sont sautés. Le périphérique USB connecté n’est pas pris en charge par cet appareil. ! Connectez un périphérique de stockage de masse USB compatible. ! Déconnectez votre périphérique et remplacezle par un périphérique de stockage USB compatible. Panne de communication. Effectuez une des opérations suivantes. –Coupez et remettez le contact d’allumage. –Déconnectez le périphérique de stockage USB. –Choisissez une autre source. Revenez ensuite à la source USB. Format CD non pris en charge. Utilisez un autre disque. La sécurité est activée sur le périphérique de stockage USB. Suivez les instructions du périphérique de stockage USB pour désactiver la sécurité. FORMAT READ PROTECT Tous les fichiers sur le disque inséré intègrent la protection par DRM. Utilisez un autre disque. Périphérique de stockage USB/iPod FORMAT READ Le début de la lecture et le début de l’émission des sons sont parfois décalés. Attendez que le message disparaisse pour entendre les sons. NO AUDIO Absence de plages musicales. Transférez les fichiers audio vers le périphérique de stockage USB et procédez à la connexion. SKIPPED CHECK USB Le connecteur USB ou le câble USB est en court-circuit. Vérifiez que le connecteur USB ou le câble USB n’est pas coincé ou endommagé. CHECK USB Le périphérique de stockage USB connecté consomme plus que le courant maximal autorisé. Déconnectez le périphérique de stockage USB et ne l’utilisez pas. Mettez le contact sur OFF, puis sur ACC ou ON, et ne connectez que des périphériques de stockage USB compatibles. Panne iPod. Déconnectez le câble de l’iPod. Quand le menu principal de l’iPod est affiché, reconnectez et réinitialisez l’iPod. Application START UP APP Français Le début de la lecture et le début de l’émission des sons sont parfois décalés. Attendez que le message disparaisse pour entendre les sons. L’application n’a pas encore démarré. Suivez les instructions qui s’affichent à l’écran. Conseils sur la manipulation Disques et lecteur Utilisez uniquement des disques affichant l’un ou l’autre des logos suivants. ERROR-23 Le périphérique de stockage USB n’a pas été formaté avec FAT12, FAT16 ou FAT32. Le périphérique de stockage USB doit être formaté avec FAT12, FAT16 ou FAT32. ERROR-16 La version du firmware de l’iPod est ancienne. Mettez à jour la version de l’iPod. Panne iPod. Déconnectez le câble de l’iPod. Quand le menu principal de l’iPod est affiché, reconnectez et réinitialisez l’iPod. Utilisez des disques 12 cm. Utilisez seulement des disques conventionnels de forme circulaire. Les types de disques suivants ne peuvent pas être utilisés avec cet appareil. ! DualDiscs ! Disques 8 cm : Les tentatives d’utilisation de tels disques avec un adaptateur peuvent entraîner un dysfonctionnement de l’appareil. ! Disques de forme bizarre STOP Aucune plage musicale dans la liste en cours. Sélectionnez une liste qui contient les plages musicales. ! Disques autres que les CD ! Disques endommagés, y compris les disques fendillés, ébréchés ou voilés ! Disques CD-R/RW non finalisés Fr <QRD3247-B> 31 31 Black plate (32,1) Annexe Informations complémentaires Ne touchez pas la surface enregistrée des disques. Rangez les disques dans leur coffret dès que vous ne les écoutez plus. Ne posez aucune étiquette sur la surface des disques, n’écrivez pas sur un disque, n’appliquez aucun agent chimique sur un disque. Pour nettoyer un CD, essuyez le disque avec un chiffon doux en partant du centre vers l’extérieur. La condensation peut perturber temporairement le fonctionnement du lecteur. Laissez celui-ci s’adapter à la température plus élevée pendant une heure environ. Essuyez également les disques humides avec un chiffon doux. La lecture de certains disques peut être impossible en raison des caractéristiques du disque, de son format, de l’application qui l’a enregistré, de l’environnement de lecture, des conditions de stockage ou d’autres conditions. Les cahots de la route peuvent interrompre la lecture d’un disque. Lors de l’utilisation de disques dont la surface de l’étiquette est imprimable, vérifiez les instructions et les avertissements des disques. L’insertion et l’éjection peuvent ne pas être possibles selon les disques. L’utilisation d’un tel disque risque d’endommager cet appareil. Ne posez aucune étiquette disponible dans le commerce ou tout autre matériau sur la surface des disques. ! Les disques pourraient se déformer et devenir injouables. ! Les étiquettes pourraient se décoller pendant la lecture et empêcher l’éjection des disques, ce qui pourrait endommager l’appareil. Périphérique de stockage USB Les connexions via un concentrateur USB ne sont pas prises en charge. Ne connectez aucun périphérique autre qu’un périphérique de stockage USB. Fixez fermement le périphérique de stockage USB lors de la conduite. Ne laissez pas le périphérique de stockage USB tomber sur le plancher, où il pourrait gêner le bon fonctionnement de la pédale de frein ou d’accélérateur. En fonction du périphérique de stockage USB, les problèmes suivants peuvent survenir. ! Le fonctionnement peut varier. ! Le périphérique de stockage peut ne pas être reconnu. ! Les fichiers peuvent ne pas être lus correctement. ! Le périphérique peut générer des interférences sonores lorsque vous écoutez la radio. Informations complémentaires Quelques mots sur les réglages de l’iPod ! Lorsqu’un iPod est connecté, cet appareil désactive le réglage EQ (égaliseur) de l’iPod afin d’optimiser l’acoustique. Le réglage EQ original est rétabli lorsque l’iPod est déconnecté. ! Vous ne pouvez pas mettre la fonction de répétition hors service sur l’iPod quand vous utilisez cet appareil. La fonction de répétition est positionnée automatiquement sur répétition de toutes les plages quand vous connectez l’iPod à cet appareil. Tout texte incompatible enregistré sur l’iPod ne sera pas affiché par cet appareil. MP3i (MP3 interactif), mp3 PRO : incompatible WAV Extension de fichier : .wav Bits de quantification : 8 et 16 (LPCM), 4 (MS ADPCM) Fréquence d’échantillonnage : 16 kHz à 48 kHz (LPCM), 22,05 kHz et 44,1 kHz (MS ADPCM) ! Vous ne pouvez pas utiliser cette fonction avec USB MTP. Formats audio compressés compatibles (disque, USB) WMA Extension de fichier : .wma iPod Liste de lecture m3u : incompatible Débit binaire : 48 kbit/s à 320 kbit/s (CBR), 48 kbit/s à 384 kbit/s (VBR) Ne laissez pas l’iPod dans un endroit soumis à une température élevée. Fréquence d’échantillonnage : 32 kHz, 44,1 kHz, 48 kHz Attachez fermement l’iPod pendant que vous conduisez. Ne laissez pas l’iPod tomber sur le plancher, où il pourrait gêner le bon fonctionnement de la pédale de frein ou d’accélérateur. Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream avec vidéo : incompatible MP3 Extension de fichier : .mp3 Débit binaire : 8 kbit/s à 320 kbit/s (CBR), VBR Fréquence d’échantillonnage : 8 kHz à 48 kHz (32 kHz, 44,1 kHz, 48 kHz pour accentuation) Informations supplémentaires Seuls les 32 premiers caractères d’un nom de fichier (incluant l’extension de fichier) ou d’un nom de dossier peuvent être affichés. Les textes russes à afficher sur cet appareil doivent être codés avec un des jeux de caractères suivants : ! Unicode (UTF-8, UTF-16) ! Un jeu de caractères autre que Unicode qui est utilisé dans un environnement Windows et qui est paramétré sur Russe dans le réglage multilingue Cet appareil peut ne pas fonctionner correctement selon l’application utilisée pour encoder les fichiers WMA. Il peut se produire un léger retard au début de la lecture de fichiers audio intégrés avec des données image ou de fichiers audio stockés sur un périphérique de stockage USB avec de nombreuses hiérarchies de dossiers. Version étiquette ID3 compatible : 1.0, 1.1, 2.2, 2.3, 2.4 (la Version 2.x de l’étiquette ID3 a priorité sur la Version 1.x.) 32 Fr <QRD3247-B> 32 Black plate (33,1) Annexe Informations complémentaires Disque Hiérarchie des dossiers pouvant être lus : jusqu’à 8 niveaux (dans la pratique, la hiérarchie compte moins de 2 niveaux). Dossiers pouvant être lus : jusqu’à 99 PRÉCAUTION ! Pioneer ne garantit pas la compatibilité avec tous les périphériques de stockage de masse USB et décline toute responsabilité en cas de perte de données sur des lecteurs multimédia, smartphones ou autres périphériques lors de l’utilisation de ce produit. ! Ne laissez pas de disques ou un périphérique de stockage USB dans un lieu où les températures sont élevées. Les utilisateurs d’un iPod avec connecteur Lightning doivent utiliser le câble Lightning vers USB (fourni avec l’iPod). Les utilisateurs d’un iPod avec Dock Connector doivent utiliser le CD-IU51. Pour plus de détails, consultez votre revendeur. Pour des détails sur la compatibilité fichier/format, reportez-vous aux manuels de l’iPod. Livre audio, podcast : compatible Lecture multi-session : compatible Transfert des données en écriture par paquet : incompatible Quelle que soit la durée du silence entre les plages musicales de l’enregistrement original, la lecture des disques d’audio compressé s’effectue avec une courte pause entre les plages musicales. Périphérique de stockage USB Hiérarchie des dossiers pouvant être lus : jusqu’à 8 niveaux (dans la pratique, la hiérarchie compte moins de 2 niveaux). Dossiers pouvant être lus : jusqu’à 500 Fichiers pouvant être lus : jusqu’à 15 000 Lecture des fichiers protégés par des droits d’auteur : incompatible Périphérique de stockage USB partitionné : Seule la première partition peut être lue. Il peut se produire un léger retard au début de la lecture de fichiers audio sur un périphérique de stockage USB avec de nombreuses hiérarchies de dossiers. Compatibilité iPod Cet appareil prend en charge uniquement les modèles d’iPod suivants. Conçu pour ! iPod touch (5ème génération) ! iPod touch (4ème génération) ! iPod touch (3ème génération) ! iPod touch (2ème génération) ! iPod touch (1ère génération) ! iPod classic ! iPod avec vidéo ! iPod nano (7ème génération) ! iPod nano (6ème génération) ! iPod nano (5ème génération) ! iPod nano (4ème génération) ! iPod nano (3ème génération) ! iPod nano (2ème génération) ! iPod nano (1ère génération) ! iPhone 5 ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone Selon la génération ou la version de l’iPod, certaines fonctions peuvent ne pas être disponibles. Les opérations peuvent différer selon la version du logiciel iPod. PRÉCAUTION Pioneer n’accepte aucune responsabilité en cas de perte de données sur l’iPod, même si la perte de données se produit pendant l’utilisation de cet appareil. Séquence des fichiers audio Sur cet appareil, l’utilisateur ne peut pas affecter de numéros de dossier ni spécifier les séquences de lecture. Exemple de hiérarchie 01 02 1 2 03 3 4 04 5 6 05 Niveau 1 Niveau 2 Niveau 3 Niveau 4 : Dossier : Fichier d’audio compressé 01 à 05 : Numéro de dossier 1 à 6 : Séquence de lecture Périphérique de stockage USB La séquence de lecture est identique à la séquence enregistrée dans le périphérique de stockage USB. Pour spécifier la séquence de lecture, la méthode suivante est recommandée. 1 Créez un nom de fichier en incluant des nombres qui spécifient la séquence de lecture (par exemple, 001xxx.mp3 et 099yyy.mp3). 2 Placez ces fichiers dans un dossier. 3 Enregistrez le dossier contenant les fichiers sur le périphérique de stockage USB. Toutefois, avec certains environnements système, vous ne pouvez pas spécifier la séquence de lecture. Pour les lecteurs audio portables USB, la séquence est différente et dépend du lecteur. Français Fichiers pouvant être lus : jusqu’à 999 Système de fichiers : ISO 9660 Niveau 1 et 2, Romeo, Joliet Informations complémentaires Tableau des caractères cyrilliques D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю D : Affichage C : Caractère Disque La séquence de sélection des dossiers ou d’autres opérations peut différer en fonction du logiciel de codage ou d’écriture. Fr <QRD3247-B> 33 33 Black plate (34,1) Annexe Informations complémentaires Droits d’auteur et marques commerciales MP3 La vente de ce produit comporte seulement une licence d’utilisation privée, non commerciale, et ne comporte pas de licence ni n’implique aucun droit d’utilisation de ce produit pour une diffusion commerciale (c’est-à-dire générant des revenus) en temps réel (terrestre, par satellite, câble et/ou tout autre média), diffusion/streaming via internet, des intranets et/ou d’autres systèmes électroniques de distribution de contenu, telles que les applications audio payante ou audio à la demande. Une licence indépendante est requise pour de telles utilisations. Pour les détails, veuillez visiter le site http://www.mp3licensing.com. WMA Windows Media est une marque déposée ou une marque commerciale de Microsoft Corporation aux États-Unis et/ou dans d’autres pays. Ce produit intègre une technologie détenue par Microsoft Corporation, qui ne peut être utilisée et distribuée que sous licence de Microsoft Licensing, Inc. iPod et iPhone iPhone, iPod, iPod classic, iPod nano et iPod touch sont des marques commerciales d’Apple Inc., déposées aux États-Unis et dans d’autres pays. Lightning est une marque commerciale d’Apple Inc. Les accessoires électroniques portant la mention « Made for iPod » et « Made for iPhone » ont été conçus pour fonctionner respectivement avec un iPod ou un iPhone et sont certifiés conformes aux exigences d’Apple par le fabricant. Apple n’est pas responsable pour le fonctionnement de cet appareil ou de sa compatibilité avec les normes réglementaires et de sécurité. Veuillez noter que l’emploi de cet accessoire avec un iPod ou un iPhone peut affecter les performances sans fil. Androidä Android est une marque commerciale de Google Inc. Informations complémentaires Caractéristiques techniques Généralités Tension d’alimentation ..... 14,4 V CC (10,8 V à 15,1 V acceptable) Mise à la masse ............... Pôle négatif Consommation maximale ................................... 10,0 A Dimensions (L × H × P) : DIN Châssis ............................ 178 mm × 100 mm × 157 mm Panneau avant ................. 188 mm × 118 mm × 25 mm D Châssis ............................ 178 mm × 100 mm × 165 mm Panneau avant ................. 170 mm × 96 mm × 17 mm Poids ............................... 1,2 kg Audio Puissance de sortie maximale ................................... 50 W × 4 70 W × 1/2 W (pour le hautparleur d’extrêmes graves) Puissance de sortie continue ................................... 22 W × 4 (50 Hz à 15 000 Hz, THD 5 %, impédance de charge 4 W, avec les deux canaux entraînés) Impédance de charge ...... 4 W (4 W à 8 W acceptable) Niveau de sortie maximum de la sortie préamp ................................... 2,0 V Correction physiologique ................................... +10 dB (100 Hz), +6,5 dB (10 kHz) (volume : –30 dB) Égaliseur (Égaliseur graphique à 5 bandes) : Fréquence ........................ 80 Hz/250 Hz/800 Hz/2,5 kHz/ 8 kHz Plage d’égalisation .......... ±12 dB (par pas de 2 dB) Haut-parleur d’extrêmes graves (mono) : Fréquence ........................ 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pente ............................... –12 dB/oct, –24 dB/oct Gain ................................ +6 dB à –24 dB Phase .............................. Normale/Inverse Lecteur de CD Système ........................... Compact Disc Digital Audio Disques utilisables ........... Disques compacts Rapport signal/bruit ......... 94 dB (1 kHz) (réseau IEC-A) 34 Nombre de canaux ........... 2 (stéréo) Format de décodage MP3 ................................... MPEG-1 & 2 Couche Audio 3 Format de décodage WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canaux audio) (Windows Media Player) Format du signal WAV ...... PCM Linéaire & MS ADPCM (Non compressé) USB Spécification standard USB ................................... USB 2.0 vitesse pleine Alimentation maximale .... 1 A Classe USB ...................... MSC (Mass Storage Class) Système de fichiers .......... FAT12, FAT16, FAT32 Format de décodage MP3 ................................... MPEG-1 & 2 Couche Audio 3 Format de décodage WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canaux audio) (Windows Media Player) Format du signal WAV ...... PCM Linéaire & MS ADPCM (Non compressé) Syntoniseur FM Gamme de fréquence ....... 87,5 MHz à 108,0 MHz Sensibilité utile ................ 9 dBf (0,8 µV/75 W, mono, S/B : 30 dB) Rapport signal/bruit ......... 72 dB (réseau IEC-A) Syntoniseur MW (PO) Gamme de fréquence ....... 531 kHz à 1 602 kHz Sensibilité utile ................ 25 µV (S/B : 20 dB) Rapport signal/bruit ......... 62 dB (réseau IEC-A) Syntoniseur LW (GO) Gamme de fréquence ....... 153 kHz à 281 kHz Sensibilité utile ................ 28 µV (S/B : 20 dB) Rapport signal/bruit ......... 62 dB (réseau IEC-A) Remarque Les caractéristiques et la présentation peuvent être modifiées sans avis préalable. Fr <QRD3247-B> 34 Black plate (35,1) Français Fr <QRD3247-B> 35 35 Black plate (36,1) Sezione Prima di iniziare 01 Grazie per aver acquistato questo prodotto PIONEER Leggere attentamente questo manuale prima di utilizzare il prodotto, per assicurarne il corretto utilizzo. È particolarmente importante leggere e osservare le precauzioni contrassegnate da AVVERTENZA e ATTENZIONE contenute in questo manuale. Conservare il manuale in un luogo sicuro e accessibile, per consultazione futura. Prima di iniziare Informazioni sull’unità Le frequenze del sintonizzatore di questa unità sono destinate all’uso in Europa occidentale, in Asia, nel Medio Oriente, in Africa e in Oceania. L’uso in altre aree può dare come risultato una ricezione non adeguata. La funzione RDS (Radio Data System) è utilizzabile solo nelle aree in cui vengono trasmessi segnali RDS per stazioni FM. AVVERTENZA Se si vuole eliminare questo prodotto, non gettarlo insieme ai rifiuti domestici. Esiste un sistema di raccolta differenziata in conformità alle leggi che richiedono appositi trattamenti, recupero e riciclo. Gli utenti privati dei Paesi membri dell’Unione Europea, della Svizzera e della Norvegia possono portare i propri prodotti elettronici gratuitamente presso i centri di raccolta specificati o presso il rivenditore al dettaglio (se l’acquisto è stato eseguito presso un rivenditore di questo tipo). Per i Paesi non specificati in precedenza, contattare le autorità locali per informazioni sul corretto metodo di smaltimento. In questo modo si garantirà che il prodotto smaltito subisca i processi di trattamento, recupero e riciclaggio necessari per prevenire i potenziali effetti negativi per l’ambiente e la salute umana. 36 ! Non cercare di installare o effettuare interventi di manutenzione sul prodotto. L’installazione o l’esecuzione di interventi di manutenzione sul prodotto da parte di persone sprovviste delle qualifiche o dell’esperienza richiesta per apparecchi elettronici e accessori automobilistici potrebbe risultare pericolosa ed esporre a rischi di scosse elettriche e di altre situazioni pericolose. ! Non cercare di utilizzare i comandi dell’unità durante la guida. Prima di utilizzare i comandi dell’unità, parcheggiare il veicolo in un luogo sicuro. ATTENZIONE Questo apparecchio è un prodotto al laser di Classe 1 secondo le norme di sicurezza dei prodotti al laser IEC 60825-1:2007. PRODOTTO LASER DI CLASSE 1 In caso di problemi Nel caso che questa unità non funzioni correttamente, contattare il rivenditore o il Centro di assistenza autorizzato PIONEER più vicino. ATTENZIONE ! Non lasciare che questa unità entri in contatto con liquidi, in caso contrario possono verificarsi scosse elettriche. Inoltre, se questa unità entra in contatto con liquidi, può subire danni oppure emettere fumo o surriscaldarsi. ! Il CarStereo-Pass Pioneer può essere usato solo in Germania. ! Mantenere sempre il volume basso abbastanza da poter udire i suoni provenienti dall’esterno. ! Evitare l’esposizione all’umidità. It <QRD3247-B> 36 Black plate (37,1) Sezione Uso dell’unità Uso dell’unità Unità principale 1 2 ATTENZIONE 3 4 5 Utilizzare un cavo USB Pioneer opzionale (CDU50E) per collegare un lettore audio USB o un dispositivo di memoria USB, in quanto se i dispositivi vengono collegati direttamente all’unità, sporgeranno dalla stessa e potrebbero risultare pericolosi. Indicazioni sul display 2 1 89 h (espulsione) 2 iPod 3 Da 1/ 4 Vano d’inserimento dei dischi 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d a 6/ (controllo iPod) MULTI-CONTROL (M.C.) a 1 3 Sezione delle informazioni secondarie 4 TA (notiziari sul traffico) 5 TP (identificazione dei programmi sul traffico) (indietro)/DIMMER (varialuce) 6 7 Porta USB 1 Dopo aver installato l’unità, portare l’interruttore della chiave di avviamento su ON. Viene visualizzata l’indicazione SET UP. (lista) (controllo iPod) La funzione iPod di questa unità è controllata dall’iPod stesso. (lista) d b 2 b Connettore di ingresso ausiliario (AUX) (connettore stereo da 3,5 mm) Viene visualizzato quando esiste una cartella o un menu di livello inferiore. Menu di configurazione a c 4 a b cd 1 9 3 b 7 9 6 8 (Sound Retriever) LOC (ricerca di sintonia in modo locale) 8 (ripetizione) 9 (casuale) 2 Ruotare M.C. per selezionare YES. # Se non si effettuano operazioni con l’unità per 30 secondi, il menu di configurazione non sarà visualizzato. # Se non si desidera eseguire la configurazione in questo momento, ruotare M.C. per selezionare NO. 3 Premere M.C. per selezionare. 4 Per configurare il menu, eseguire questa procedura. Per passare all’opzione di menu successiva, occorre confermare la selezione. LANGUAGE (multilingue) Questa unità è in grado di visualizzare le informazioni di testo dei file audio compressi se sono state incorporate in inglese, russo o turco. ! Se la lingua incorporata e l’impostazione della lingua selezionata non corrispondono, le informazioni di testo potrebbero non essere visualizzate correttamente. ! Alcuni caratteri potrebbero non essere visualizzati correttamente. 1 Ruotare M.C. per selezionare l’impostazione desiderata. ENG (Inglese)—РУС (Russo)—TUR (Turco) 2 Premere M.C. per confermare la selezione. CLOCK SET (impostazione dell’orologio) 1 2 3 4 Italiano 6 7 5 a Sezione delle informazioni principali ! Sintonizzatore: banda e frequenza ! RDS: nome di servizio del programma, informazioni PTY e altre informazioni letterali ! Sintolettore, dispositivo di memoria USB e iPod: tempo di riproduzione trascorso e informazioni di testo 02 Ruotare M.C. per regolare le ore. Premere M.C. per selezionare i minuti. Ruotare M.C. per regolare i minuti. Premere M.C. per confermare la selezione. FM STEP (passo di sintonizzazione FM) Utilizzare FM STEP per impostare le opzioni relative al passo di sintonizzazione FM (impostazioni per il passo di ricerca). 1 Ruotare M.C. per selezionare il passo di sintonizzazione FM. 100 (100 kHz)—50 (50 kHz) 2 Premere M.C. per confermare la selezione. Viene visualizzata l’indicazione QUIT. ! Il passo di sintonizzazione manuale è fissato a 50 kHz. ! Se le opzioni AF e TA sono disattivate, il passo di ricerca è fissato a 50 kHz, anche se è stato impostato su 100. 5 Per completare le impostazioni, ruotare M.C. per selezionare YES. # Se si desidera modificare ancora l’impostazione, ruotare M.C. per selezionare NO. 6 Premere M.C. per selezionare. It <QRD3247-B> 37 37 Black plate (38,1) Sezione Uso dell’unità 02 Note ! È possibile configurare le opzioni di menu dal menu di sistema e dal menu iniziale. Per informazioni dettagliate sulle impostazioni, vedere Menu di sistema a pagina 44 e Menu iniziale a pagina 44. ! È possibile annullare il menu di configurazione premendo SRC/OFF. Funzionamento di base Accensione dell’unità 1 Premere SRC/OFF per accendere l’unità. Spegnimento dell’unità 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. Selezione di una sorgente 1 Premere SRC/OFF per passare in rassegna: RADIO—CD—USB/iPod—APP (applicazione) —AUX ! Quando è in uso la connessione MTP, viene visualizzata l’indicazione USB MTP. ! Se è collegato un iPod ed è stata selezionata una sorgente diversa da iPod, è possibile passare a iPod premendo iPod. Regolazione del volume 1 Ruotare M.C. per regolare il volume. Nota Quando il conduttore isolato blu/bianco di questa unità viene collegato al terminale di controllo del relè dell’antenna automatica, l’antenna dell’automobile si estende quando si accende l’unità. Per ritirare l’antenna, spegnere la sorgente. 38 Uso dell’unità Operazioni col menu più frequentemente utilizzate Ritorno al display precedente Ritorno all’elenco precedente (la cartella superiore di un livello) 1 Premere /DIMMER. Ritorno al display normale Annullamento del menu principale 1 Premere BAND/ . Ritorno al display normale dall’elenco 1 Premere BAND/ . Note ! Per ulteriori dettagli sulla funzione SEEK, vedere SEEK (impostazione tasto sinistro/destro) a pagina 39. ! È possibile attivare e disattivare (on/off) la funzione AF (ricerca delle frequenze alternative) di questa unità. Per le operazioni normali di sintonizzazione, la funzione AF deve essere disattivata (vedere AF (ricerca delle frequenze alternative) a pagina 39). Memorizzazione e richiamo delle stazioni per ciascuna banda Uso dei tasti di preselezione sintonia Radio Funzionamento di base Selezione di una banda 1 Premere BAND/ fino a quando viene visualizzata la banda desiderata (FM1, FM2, FM3 per FM o MW/LW). Selezione delle stazioni preselezionate 1 Premere c o d. ! Selezionare PCH (canale preselezionato) in SEEK per utilizzare questa funzione. Sintonizzazione manuale (passo per passo) 1 Premere c o d. ! Selezionare MAN (sintonizzazione manuale) in SEEK per utilizzare questa funzione. Ricerca 1 Premere e tenere premuto c o d e poi rilasciare. È possibile annullare la ricerca di sintonia premendo brevemente c o d. Se si spinge e si tiene premuto c o d, è possibile saltare le stazioni. La ricerca di sintonia viene avviata non appena si rilascia c o d. 1 Per memorizzare: Premere e tenere premuto uno dei tasti di preselezione sintonia (da 1/ a 6/ ) fino a quando il numero smette di lampeggiare. 2 Per richiamare: Premere uno dei tasti di preselezione sintonia (da 1/ a 6/ ). Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! FREQUENCY (nome di servizio del programma o frequenza) ! BRDCST INFO (nome di servizio del programma/Informazioni PTY) ! CLOCK (nome della sorgente e orologio) Note ! Se non è possibile ottenere il nome di servizio del programma in FREQUENCY, al suo posto viene visualizzata la frequenza di trasmissione. Se invece il nome di servizio del programma viene rilevato, verrà visualizzato. ! È possibile modificare le informazioni a seconda della banda. ! Le informazioni di testo che possono essere modificate dipendono dall’area. Uso delle funzioni PTY È possibile sintonizzarsi su una stazione usando le informazioni PTY (tipo di programma). Ricerca di una stazione RDS tramite le informazioni PTY 1 Premere (elenco). 2 Ruotare M.C. per selezionare un tipo di programma. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Premere M.C. per avviare la ricerca. L’unità ricerca una stazione che trasmette il tipo di programma selezionato. Quando viene trovata una stazione, viene visualizzato il nome di servizio del programma. ! Per annullare la ricerca premere nuovamente M.C. ! Il programma di alcune stazioni può essere diverso da quello indicato dal PTY (tipo di programma) trasmesso. ! Se nessuna stazione trasmette il tipo di programma ricercato, per circa due secondi viene visualizzata l’indicazione NOT FOUND e poi il sintonizzatore torna alla stazione originale. Elenco PTY Per ulteriori dettagli sull’elenco PTY, visitare il sito: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. It <QRD3247-B> 38 Black plate (39,1) Sezione Uso dell’unità 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. 3 Ruotare M.C. per selezionare la funzione. Dopo aver effettuato la selezione, è possibile regolare le funzioni descritte di seguito. # Se è selezionata la banda MW/LW, è possibile selezionare solo BSM, LOCAL o SEEK. FM SETTING (impostazioni della qualità dell’audio FM) BSM (memorizzazione delle stazioni migliori) La funzione BSM (memorizzazione delle stazioni migliori) memorizza automaticamente le sei stazioni più forti in ordine di forza del segnale. 1 Premere M.C. per attivare la funzione BSM. Per annullare, premere nuovamente M.C. REGIONAL (regionale) Quando si utilizza la funzione AF, la funzione regionale limita la selezione alle stazioni che trasmettono programmi regionali. 1 Premere M.C. per attivare o disattivare la funzione regionale. La ricerca di sintonia in modo locale consente di sintonizzare solo le stazioni radio con segnali radio sufficientemente potenti per una buona ricezione. 1 Premere M.C. per selezionare l’impostazione desiderata. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 L’impostazione di livello massimo consente la ricezione solo delle stazioni più forti, mentre i livelli più bassi consentono di ricevere stazioni più deboli. TA (attesa di notiziari sul traffico) 1 Premere M.C. per attivare o disattivare l’attesa di notiziari sul traffico. AF (ricerca delle frequenze alternative) 1 Premere M.C. per attivare e disattivare la funzione AF. NEWS (interruzione dei programmi per i notiziari) 1 Premere M.C. per attivare o disattivare la funzione NOTIZIE. SEEK (impostazione tasto sinistro/destro) È possibile assegnare una funzione ai tasti sinistro e destro dell’unità. Selezionare MAN (sintonizzazione manuale) per eseguire la sintonizzazione manuale o PCH (canali preselezionati) per scegliere i canali preselezionati. 1 Premere M.C. per selezionare MAN o PCH. CD/CD-R/CD-RW e dispositivi di memoria USB Collegamento MTP È possibile connettere i dispositivi Android compatibili MTP (che eseguono Android OS 4.0 o versione successiva) tramite collegamento MTP, utilizzando la sorgente USB. Per collegare il dispositivo Android, utilizzare il cavo fornito col dispositivo. Nota Questa funzione non è compatibile con i file WAV. Funzionamento di base Riproduzione di CD/CD-R/CD-RW 1 Inserire un disco nel vano d’inserimento dei dischi, con il lato dell’etichetta rivolto verso l’alto. Espulsione dei CD/CD-R/CD-RW 1 Premere h. 02 Esegue l’avanzamento rapido/la modalità inversa rapida 1 Premere e tenere premuto c o d. ! Quando si riproducono file audio compressi, durante l’avanzamento rapido e la modalità inversa non viene emesso audio. Ritorno alla cartella principale 1 Premere e tenere premuto BAND/ . Passaggio da audio compresso a CD-DA 1 Premere BAND/ . Passaggio da un dispositivo di memoria per la riproduzione ad un altro Se sono disponibili più dispositivi di memorizzazione di massa conformi con lo standard Mass Storage Class USB, è possibile alternare i dispositivi di memoria per la riproduzione. 1 Premere BAND/ . ! È possibile alternare fino a 32 differenti dispositivi di memoria. Italiano È possibile impostare il livello della qualità dell’audio in modo che corrisponda alle condizioni del segnale trasmesso della banda FM. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione desiderata. ! STANDARD – Corrisponde all’impostazione standard. ! HI-FI – Utilizzare questa impostazione per dare la priorità all’alta qualità dell’audio stereo. ! STABLE – Utilizzare questa impostazione per dare la priorità alla riduzione dei disturbi dell’audio mono. Uso dell’unità Nota Quando non utilizzati, scollegare i dispositivi di memoria USB dall’unità. Riproduzione dei brani registrati su un dispositivo di memoria USB 1 Sollevare la copertura della porta USB. 2 Collegare il dispositivo di memoria USB utilizzando un cavo USB. Arresto della riproduzione dei file sul dispositivo di memoria USB 1 È possibile scollegare il dispositivo di memoria USB in qualsiasi momento. Selezione di una cartella 1 Premere 1/ o 2/ . Selezione di una traccia 1 Premere c o d. LOCAL (ricerca di sintonia in modo locale) It <QRD3247-B> 39 39 Black plate (40,1) Sezione Uso dell’unità 02 Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: CD-DA ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) CD-TEXT ! TRACK INFO (titolo del brano/artista del brano/titolo del disco) ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) MP3/WMA/WAV ! TRACK INFO (titolo del brano/nome dell’artista/titolo dell’album) ! FILE INFO (nome del file/nome della cartella) ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) Selezione e riproduzione di file/ brani dall’elenco dei nomi 1 Premere per passare alla modalità dell’elenco dei nomi file/brani. 2 Utilizzare M.C. per selezionare il nome del file (o il nome della cartella) desiderato. Selezione di un file o di una cartella 1 Ruotare M.C. Riproduzione 1 Quando è selezionato un file o un brano, premere M.C. 40 Uso dell’unità Visualizzazione di un elenco dei file (o delle cartelle) nella cartella selezionata 1 Quando è selezionata una cartella, premere M.C. Riproduzione di un brano nella cartella selezionata 1 Quando è selezionata una cartella, premere e tenere premuto M.C. Operazioni con i pulsanti speciali Selezione di un intervallo di ripetizione per alternare: 1 Premere 6/ CD/CD-R/CD-RW ! ALL – Ripete tutti i brani ! ONE – Ripete il brano corrente ! FLD – Ripete la cartella corrente Dispositivo di memoria USB ! ALL – Ripete tutti i file ! ONE – Ripete il file corrente ! FLD – Ripete la cartella corrente Riproduzione di brani in ordine casuale per attivare o disattivare la ri1 Premere 5/ produzione casuale. I brani contenuti nell’intervallo di ripetizione selezionato vengono riprodotti in ordine casuale. ! Per cambiare brano durante la riproduzione casuale, premere d per passare al brano successivo. Se si preme c, viene riavviata la riproduzione del brano corrente dall’inizio. Messa in pausa della riproduzione 1 Premere 4/PAUSE per attivare o disattivare la pausa. Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) 1 Premere 3/S.Rtrv per passare in rassegna: 1—2—OFF (disattivata) 1 è efficace per le velocità di compressione basse, mentre 2 è efficace per le velocità di compressione alte. Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. Dopo aver effettuato la selezione, è possibile regolare la funzione descritta di seguito. S.RTRV (Sound Retriever) Questa funzione migliora automaticamente l’audio compresso e ripristina il suono completo. 1 Premere M.C. per selezionare l’impostazione desiderata. Per ulteriori dettagli, vedere Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) a pagina 40. iPod Funzionamento di base Riproduzione di brani da un iPod 1 Sollevare la copertura della porta USB. 2 Collegare un iPod all’ingresso USB. La riproduzione viene eseguita automaticamente. Selezione di un brano (capitolo) 1 Premere c o d. Selezione di un album 1 Premere 1/ o 2/ . Esegue l’avanzamento rapido/la modalità inversa rapida 1 Premere e tenere premuto c o d. Note ! Non è possibile accendere o spegnere l’iPod se la modalità di controllo è impostata su CTRL AUDIO. ! Scollegare gli auricolari dall’iPod prima di collegarlo a questa unità. ! L’iPod si spegne circa due minuti dopo che l’interruttore della chiave di avviamento è stato portato in posizione OFF. Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! TRACK INFO (titolo del brano/nome dell’artista/titolo dell’album) ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) It <QRD3247-B> 40 Black plate (41,1) Sezione Uso dell’unità Scorrimento dei brani 1 Per passare al menu superiore della ricerca delle liste, premere . 2 Utilizzare M.C. per selezionare una categoria/brano. Modifica del nome del brano o della categoria 1 Ruotare M.C. Liste di riproduzione—artisti—album— brani —podcast—generi—compositori—audiolibri Visualizzazione di un elenco dei brani nella categoria selezionata 1 Mentre è selezionata una categoria, premere M.C. Riproduzione di un brano nella categoria selezionata 1 Mentre è selezionata una categoria, premere e tenere premuto M.C. Ricerca alfabetica nella lista 1 Quando viene visualizzata una lista per la cateper passare alla goria selezionata, premere modalità di ricerca alfabetica. ! È possibile anche passare alla modalità di ricerca alfabetica ruotando M.C. due volte. 2 Ruotare M.C. per selezionare una lettera. 3 Premere M.C. per visualizzare l’elenco in ordine alfabetico. ! Per annullare la ricerca, premere /DIMMER. Note ! È possibile riprodurre le liste di riproduzione create con l’applicazione per computer (MusicSphere). L’applicazione sarà disponibile sul nostro sito web. ! Le liste di riproduzione create con l’applicazione per computer (MusicSphere) vengono visualizzate in forma abbreviata. Operazioni con i pulsanti speciali Riproduzione di brani correlati al brano attualmente in riproduzione Selezione di un intervallo di ripetizione 1 Premere 6/ per alternare: ! ONE – Ripete il brano corrente ! ALL – Ripete tutti i brani dell’elenco selezionato ! Se la modalità di controllo è impostata su CTRL iPod, l’intervallo di riproduzione ripetuta sarà uguale a quello impostato per l’iPod collegato. È possibile riprodurre i brani dalle liste seguenti. • Lista degli album dell’artista correntemente in riproduzione • Lista dei brani dell’album correntemente riprodotto • Lista degli album del genere correntemente in riproduzione Selezione di un intervallo di riproduzione casuale (modalità shuffle) per alternare: 1 Premere 5/ ! SNG – Riproduce in ordine casuale i brani contenuti nella lista selezionata. ! ALB – Riproduce i brani contenuti in un album selezionato in ordine casuale. ! OFF – Non viene eseguita la riproduzione casuale. Riproduzione casuale di tutti i brani (shuffle all) per attivare la 1 Premere e tenere premuto 5/ riproduzione casuale di tutti i brani. ! Per disattivare la riproduzione casuale di tutti i brani, selezionare OFF nella riproduzione casuale. Per ulteriori dettagli, vedere Selezione di un intervallo di riproduzione casuale (modalità shuffle) a pagina 41. Messa in pausa della riproduzione 1 Premere 4/PAUSE per attivare o disattivare la pausa. Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) 1 Premere 3/S.Rtrv per passare in rassegna: 1—2—OFF (disattivata) 1 è efficace per le velocità di compressione basse, mentre 2 è efficace per le velocità di compressione alte. 1 Premere e tenere premuto per passare alla modalità di riproduzione collegamento. 2 Ruotare M.C. per modificare la modalità; premere per selezionare. ! ARTIST – Riproduce un album dell’artista attualmente in riproduzione. ! ALBUM – Riproduce un brano dell’album attualmente in riproduzione. ! GENRE – Riproduce un album del genere attualmente in riproduzione. Dopo il brano attualmente in riproduzione, verrà riprodotto il brano/album selezionato. Note ! È possibile annullare il brano/album selezionato, se si utilizzano funzioni diverse dalla ricerca collegamento (ad esempio l’avanzamento o la modalità inversa rapidi). ! A seconda del brano selezionato per la riproduzione, la fine del brano attualmente in riproduzione e l’inizio del brano/album selezionato potrebbero essere tagliati. Utilizzo della funzione iPod dell’unità dall’iPod È possibile controllare la funzione iPod di questa unità tramite l’apparecchio iPod collegato. CTRL iPod non è compatibile con i seguenti modelli di iPod. ! iPod nano di prima generazione ! iPod con video 02 % Premere BAND/ tà di controllo. per alternare la modali- ! CTRL iPod – È possibile utilizzare la funzione iPod di questa unità tramite l’apparecchio iPod collegato. ! CTRL AUDIO – È possibile controllare la funzione iPod direttamente da questa unità. È inoltre possibile alternare la modalità di controllo premendo iPod. Note ! Se si passa alla modalità di controllo CTRL iPod, il brano attualmente in riproduzione viene messo in pausa. Utilizzare i comandi dell’iPod per riprendere la riproduzione. ! Anche se la modalità di controllo è impostata su CTRL iPod, è possibile controllare le seguenti funzioni da questa unità. Italiano Riproduzione 1 Mentre è selezionato un brano, premere M.C. Uso dell’unità — Pausa — Avanzamento rapido/modalità inversa rapida — Selezione di un brano (capitolo) ! È possibile controllare il volume solo da questa unità. Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. 3 Ruotare M.C. per selezionare la funzione. Dopo aver effettuato la selezione, è possibile regolare le funzioni descritte di seguito. ! AUDIO BOOK non è disponibile se come modalità di controllo è selezionata l’impostazione CTRL iPod. Per ulteriori dettagli, vedere Utilizzo della funzione iPod dell’unità dall’iPod a pagina 41. It <QRD3247-B> 41 41 Black plate (42,1) Sezione Uso dell’unità 02 AUDIO BOOK (velocità audiolibri) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione preferita. ! FASTER – Riproduzione più veloce del normale ! NORMAL – Riproduzione normale ! SLOWER – Riproduzione più lenta del normale S.RTRV (Sound Retriever) 1 Premere M.C. per selezionare l’impostazione desiderata. Per ulteriori dettagli, vedere Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) a pagina 41. Uso delle applicazioni del dispositivo collegato È possibile utilizzare questa unità per eseguire riproduzioni in streaming e controllare i brani nelle applicazioni per iPhone o solo per riproduzioni in streaming. Uso dell’unità Importante L’utilizzo di applicazioni di terze parti potrebbe comportare o richiedere di fornire informazioni personali di identificazione attraverso la creazione di un account utente o in altro modo e, per alcune applicazioni, attraverso l’invio di dati di geolocalizzazione. TUTTE LE APPLICAZIONI DI TERZE PARTI SONO DI RESPONSABILITÀ ESCLUSIVA DEI RISPETTIVI FORNITORI, INCLUSI MA NON LIMITATAMENTE ALLA GESTIONE E SICUREZZA DEI DATI UTENTE E ALLE PROCEDURE DI TUTELA DELLA PRIVACY. ACCEDENDO AD APPLICAZIONI DI TERZE PARTI, SI ACCETTA DI ESAMINARE I TERMINI DEL SERVIZIO E I CRITERI SULLA PRIVACY DEI FORNITORI. SE NON SI ACCETTANO I TERMINI O I CRITERI DI QUALSIASI FORNITORE O NON SI ACCONSENTE, DOVE SIA APPLICABILE, ALL’USO DEI DATI DI GEOLOCALIZZAZIONE, NON UTILIZZARE TALI APPLICAZIONI DI TERZE PARTI. Informazioni sulla compatibilità dei dispositivi collegati Di seguito sono riportate informazioni dettagliate relative ai terminali richiesti per utilizzare le applicazioni per iPhone su questa unità. Per gli utenti iPhone ! Questa funzione è compatibile con dispositivi iPhone e iPod touch. ! Il dispositivo deve eseguire iOS 5.0 o versione successiva. Note ! Per l’elenco delle applicazioni per iPhone supportate da questa unità, consultare il nostro sito web. ! Pioneer non è responsabile di eventuali problemi che possono derivare da errori o difetti del contenuto delle applicazioni. 42 ! Il contenuto e la funzione delle applicazioni supportate sono di responsabilità dei fornitori delle applicazioni. Procedura di inizio per utenti iPhone 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. 3 Ruotare M.C. per selezionare la funzione. Dopo aver effettuato la selezione, è possibile regolare le funzioni descritte di seguito. 1 Collegare un iPhone all’ingresso USB. PAUSE (pausa) 2 Selezionare APP come sorgente. 1 Premere M.C. per attivare o disattivare la pausa. 3 Avviare l’applicazione sull’iPhone e avviare la riproduzione. Funzionamento di base Selezione di una traccia 1 Premere c o d. Esegue l’avanzamento rapido/la modalità inversa rapida 1 Premere e tenere premuto c o d. Messa in pausa della riproduzione 1 Premere BAND/ per attivare la pausa o riprendere la riproduzione. Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! TRACK INFO (titolo del brano/nome dell’artista/titolo dell’album) ! APP NAME (nome dell’applicazione) ! ELAPSED TIME (tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. S.RTRV (Sound Retriever) 1 Premere M.C. per selezionare l’impostazione desiderata. 1—2—OFF (disattivata) 1 è efficace per le velocità di compressione basse, mentre 2 è efficace per le velocità di compressione alte. Regolazione dell’audio 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare AUDIO. 3 Ruotare M.C. per selezionare la funzione audio. Dopo aver effettuato la selezione, è possibile regolare le funzioni audio descritte di seguito. ! FADER non è disponibile se l’impostazione SUB.W/SUB.W è selezionata in SP-P/O MODE. Per ulteriori dettagli, vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 44. ! SUB.W e SUB.W CTRL non sono disponibili se l’impostazione REAR/REAR è selezionata in SP-P/O MODE. Per ulteriori dettagli, vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 44. It <QRD3247-B> 42 Black plate (43,1) Sezione Uso dell’unità ! SUB.W CTRL non è disponibile se l’impostazione SUB.W è selezionata in OFF. Per ulteriori dettagli, vedere SUB.W (impostazione on/off del subwoofer) a pagina 43. ! SLA non è disponibile se come sorgente è selezionata FM. FADER (regolazione dissolvenza) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il bilanciamento degli altoparlanti anteriori/posteriori. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il bilanciamento dell’altoparlante sinistro/destro. EQ SETTING (richiamo dell’equalizzatore) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’equalizzatore. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La banda di equalizzazione e il livello dell’equalizzatore possono essere personalizzati se è selezionata l’impostazione CUSTOM1 o CUSTOM2. Se si seleziona CUSTOM1 o CUSTOM2, completare la procedure descritta di seguito. Se si selezionano altre opzioni, premere M.C. per tornare al display precedente. ! L’impostazione CUSTOM1 può essere impostata separatamente per ciascuna sorgente. Tuttavia, USB, iPod e APP vengono automaticamente configurate sulla stessa impostazione. ! CUSTOM2 è un’impostazione condivisa utilizzata per tutte le sorgenti. 3 Premere M.C. per visualizzare la modalità di impostazione. 4 Premere M.C. per alternare le seguenti impostazioni: Banda d’equalizzazione—Livello equalizzatore 5 Ruotare M.C. per selezionare l’impostazione desiderata. Banda d’equalizzazione: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Livello equalizzatore: +6 a –6 LOUDNESS (sonorità) La sonorità compensa le deficienze nelle gamme delle frequenze basse e alte a basso volume. 1 Premere M.C. per selezionare l’impostazione desiderata. OFF (non attiva)—LOW (bassa)—MID (media) —HI (alta) Questa unità è dotata di un’uscita subwoofer che può essere attivata o disattivata. 1 Premere M.C. per selezionare l’impostazione desiderata. NOR (fase normale)—REV (fase invertita)— OFF (subwoofer disattivato) SUB.W CTRL (regolazione del subwoofer) Solo frequenze più basse di quelle presenti nell’intervallo selezionato vengono emesse dal subwoofer. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per alternare le seguenti impostazioni: Frequenza di taglio—Livello di uscita—Livello pendenza I valori regolabili lampeggiano. 3 Ruotare M.C. per selezionare l’impostazione desiderata. Frequenza di taglio: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Livello di uscita: da –24 a +6 Livello pendenza: –12— –24 BASS BOOST (incremento dei bassi) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare il livello desiderato. A seconda se il livello aumenta o diminuisce, viene visualizzata l’indicazione da 0 a +6. 02 Utilizzare questa funzione se si desidera ascoltare solo il segnale audio ad alta frequenza. Dagli altoparlanti verranno emesse solo le frequenze superiori al limite del filtro passa alto (HPF). 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per alternare le seguenti impostazioni: Frequenza di taglio—Livello pendenza 3 Ruotare M.C. per selezionare l’impostazione desiderata. Frequenza di taglio: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Livello pendenza: –12— –24 Italiano BALANCE (regolazione del bilanciamento) Uso dell’unità SLA (regolazione del livello della sorgente) Questa funzione impedisce che il volume cambi in modo eccessivo quando viene selezionata una sorgente diversa. ! Le impostazioni sono basate sul livello di volume FM, che rimane immutato. ! Con questa funzione è anche possibile regolare il livello di volume MW/LW. ! USB, iPod e APP vengono automaticamente configurate sulla stessa impostazione. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il volume della sorgente. Intervallo di regolazione: da +4 a –4 HPF SETTING (regolazione del filtro passa alto) SUB.W (impostazione on/off del subwoofer) It <QRD3247-B> 43 43 Black plate (44,1) Sezione Uso dell’unità 02 Menu di sistema Importante La modalità PW SAVE (risparmio energetico) viene annullata se la batteria del veicolo viene scollegata e sarà necessario riattivarla dopo aver ricollegato la batteria. Se la funzione PW SAVE (risparmio energetico) è disattivata, a seconda del metodo di collegamento, l’unità potrebbe continuare a consumare energia dalla batteria se l’interruttore della chiave di avviamento del veicolo non è dotato di posizione ACC (accessori). Uso dell’unità AUTO PI (ricerca automatica PI) L’unità può ricercare automaticamente una stazione diversa con la stessa programmazione, anche durante il richiamo delle preselezioni. 1 Premere M.C. per attivare o disattivare la ricerca automatica PI. 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. AUX (ingresso ausiliario) 3 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare INITIAL. Attivare questa impostazione se a questa unità viene collegato un dispositivo ausiliario. 1 Premere M.C. per attivare o disattivare AUX. DIMMER (varialuce) 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. 3 Ruotare M.C. per selezionare la funzione del menu di sistema. Dopo aver effettuato la selezione, è possibile regolare le funzioni del menu di sistema descritte di seguito. LANGUAGE (multilingue) 1 Premere M.C. per selezionare l’impostazione desiderata. ENG (Inglese)—РУС (Russo)—TUR (Turco) CLOCK SET (impostazione dell’orologio) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per selezionare il segmento del display dell’orologio che si desidera impostare. Ora—Minuto 3 Ruotare M.C. per regolare l’orologio. 12H/24H (nota temporale) 1 Premere M.C. per selezionare l’impostazione desiderata. 12H (formato orologio a 12 ore)—24H (formato orologio a 24 ore) 44 Menu iniziale 1 Premere M.C. per attivare e disattivare il varialuce. ! È inoltre possibile modificare l’impostazione del varialuce premendo e tenendo premuto /DIMMER. MUTE MODE (modalità di silenziamento) Il suono del sistema viene silenziato o attenuato automaticamente quando viene ricevuto un segnale da un apparecchio dotato di funzione di silenziamento. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione desiderata. ! MUTE – Silenziamento ! 20dB ATT – Attenuazione (20dB ATT ha un effetto più accentuato rispetto a 10dB ATT) ! 10dB ATT – Attenuazione PW SAVE (risparmio energetico) Attivando questa funzione, è possibile ridurre il consumo di energia della batteria. ! L’attivazione della sorgente è l’unica operazione consentita quando questa funzione è attiva. 1 Premere M.C. per attivare o disattivare la modalità di risparmio energetico. 2 Premere e tenere premuto SRC/OFF fino a visualizzare sul display il menu principale. 4 Ruotare M.C. per selezionare la funzione del menu iniziale. Dopo aver effettuato la selezione, è possibile regolare le funzioni del menu iniziale descritte di seguito. FM STEP (passo di sintonizzazione FM) 1 Premere M.C. per selezionare il passo di sintonizzazione FM. 100 (100 kHz)—50 (50 kHz) SP-P/O MODE (uscita posteriore e impostazione pre-out) Le uscite degli altoparlanti posteriori e l’uscita RCA di questa unità possono essere utilizzate per collegare altoparlanti a gamma completa o un subwoofer. Selezionare l’opzione più adatta alla configurazione. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione desiderata. ! REAR/SUB.W – Selezionare quando alle uscite degli altoparlanti posteriori sono collegati altoparlanti a gamma completa e all’uscita RCA è collegato un subwoofer. ! SUB.W/SUB.W – Selezionare quando alle uscite degli altoparlanti posteriori è collegato direttamente un subwoofer senza un amplificatore ausiliario e all’uscita RCA è collegato un subwoofer. ! REAR/REAR – Selezionare quando alle uscite degli altoparlanti posteriori e all’uscita RCA sono collegati altoparlanti a gamma completa. Se alle uscite degli altoparlanti posteriori è collegato un altoparlante a gamma completa e l’uscita RCA non viene utilizzata, è possibile selezionare REAR/SUB.W o REAR/REAR. Menu di sistema 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. 2 Premere e tenere premuto SRC/OFF fino a visualizzare sul display il menu principale. 3 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. It <QRD3247-B> 44 Black plate (45,1) Sezione Uso dell’unità Installazione 02 03 1 Collegare il cavo mini plug stereo al connettore di ingresso ausiliario (AUX). 2 Premere SRC/OFF per selezionare AUX come sorgente. Se viene visualizzato un display indesiderato Per disattivare il display indesiderato, utilizzare la procedura descritta di seguito. 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. 3 Ruotare M.C. per visualizzare DEMO OFF, quindi premere per selezionare. 4 Ruotare M.C. per selezionare YES. 5 Premere M.C. per selezionare. Con posizione ACC Senza posizione ACC ! Se questa unità viene utilizzata in condizione diverse dalle seguenti, potrebbero verificarsi incendi o malfunzionamenti. — Veicoli dotati di batteria da 12 volt e messa a terra negativa. — Altoparlanti con uscita nominale da 50 W e impedenza nominale compresa tra 4 W e 8 W. ! Per evitare rischi di cortocircuito, surriscaldamento o malfunzionamento, accertarsi di seguire le indicazioni riportate di seguito. — Prima dell’installazione, scollegare il morsetto negativo della batteria. — Assicurare i cavi con morsetti per cavi o nastro adesivo. Per proteggere i cavi, avvolgere nastro adesivo attorno agli stessi nei punti in cui entrano in contatto con parti metalliche. — Posizionare tutti i cavi in modo che non possano entrare in contatto con componenti mobili, come la leva del cambio e i binari dei sedili. — Non posizionare i cavi in luoghi soggetti a surriscaldamento, come le bocchette dell’impianto di riscaldamento. — Non collegare il cavo giallo alla batteria facendolo passare attraverso fori nel vano motore. — Rivestire tutti i connettori scollegati con nastro isolante. — Non accorciare i cavi. — Non condividere mai l’alimentazione con altri dispositivi tagliando l’isolante del cavo di alimentazione dell’unità. La capacità di carico di corrente del cavo è limitata. — Utilizzare esclusivamente un fusibile con la portata prescritta. — Non collegare mai direttamente a terra il cavo negativo dell’altoparlante. — Non legare mai assieme cavi negativi di più altoparlanti. ! Quando questa unità è accesa, i segnali di controllo vengono trasmessi dal cavo blu/ bianco. Collegarlo al telecomando del sistema di amplificazione di potenza o al terminale di controllo del relè dell’antenna automatica del veicolo (max. 300 mA 12 V CC). Se il veicolo è dotato di un’antenna a vetro, collegarla al terminale di alimentazione di potenza dell’antenna. ! Non collegare mai il cavo blu/bianco al terminale di alimentazione dell’amplificatore di potenza esterno. Inoltre, non collegarlo mai al terminale di alimentazione dell’antenna automatica. In caso contrario, la batteria potrebbe scaricarsi o potrebbero verificarsi malfunzionamenti. ! Il cavo nero è la messa a terra. I cavi di messa a terra di questa unità e di altre apparecchiature (soprattutto per i prodotti ad alta tensione, quali amplificatori di potenza) devono essere collegati separatamente. In caso contrario, se scollegati accidentalmente, potrebbero provocare incendi o malfunzionamenti. It <QRD3247-B> 45 Italiano Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! Nome sorgente ! Nome della sorgente e orologio O STAR Commutazione del display F N Nota Non è possibile selezionare la sorgente AUX se non viene attivata l’impostazione dell’apparecchio ausiliario. Per ulteriori dettagli, vedere AUX (ingresso ausiliario) a pagina 44. Importante ! Quando si installa questa unità in un veicolo che non dispone della posizione ACC (accessoria) per l’interruttore della chiave di avviamento, se non si collega il cavo rosso a un terminale accoppiato al funzionamento dell’interruttore della chiave di avviamento, la batteria potrebbe scaricarsi. OF Uso della sorgente AUX Collegamenti T 4 Ruotare M.C. per selezionare la funzione del menu di sistema. Per ulteriori dettagli, vedere Menu di sistema a pagina 44. 45 Black plate (46,1) Sezione Installazione 03 Installazione Questa unità 1 23 4 5 1 2 3 4 Ingresso antenna Fusibile (10 A) Ingresso cavo di alimentazione Ingresso telecomando cablato È possibile collegare un adattatore per telecomando cablato (venduto a parte). 5 Uscita posteriore o del subwoofer Cavo di alimentazione 3 4 5 2 7 1 6 3 4 5 6 8 a 9 e b c d 1 All’ingresso del cavo di alimentazione 2 A seconda del tipo di veicolo, la funzione di 3 e 5 potrebbe essere diversa. In questo caso, accertarsi di collegare 4 a 5 e 6 a 3. 46 3 Giallo Riserva (o accessorio) 4 Giallo Collegare al terminale di alimentazione costante 12 V. 5 Rosso Accessorio (o riserva) 6 Rosso Collegare al terminale controllato dall’interruttore di accensione (12 V CC). 7 Collegare insieme i cavi dello stesso colore. 8 Nero (messa a terra telaio) 9 Blu/bianco La posizione dei pin del connettore ISO sarà diversa a seconda del tipo di veicolo. Collegare 9 e b quando il Pin 5 è del tipo controllo antenna. In un altro tipo di veicolo, non collegare mai 9 e b. a Blu/bianco Collegare al terminale di controllo del sistema dell’amplificatore di potenza (max. 300 mA 12 V CC). b Blu/bianco Collegare al terminale di controllo del relè dell’antenna automatica (max. 300 mA 12 V CC). c Giallo/nero Se si utilizza un apparecchio dotato di funzione di silenziamento, collegare questo cavo al cavo di silenziamento audio di tale apparecchio. In caso contrario, non collegare il cavo di silenziamento audio. d Cavi altoparlanti Bianco: Anteriore sinistro + Bianco/nero: Anteriore sinistro * Grigio: Anteriore destro + Grigio/nero: Anteriore destro * Verde: Posteriore sinistro + o subwoofer + Verde/nero: Posteriore sinistro * o subwoofer * Viola: Posteriore destro + o subwoofer + Viola/nero: Posteriore destro * o subwoofer * e Connettore ISO In alcuni veicoli, il connettore ISO potrebbe essere diviso in due. In questo caso, accertarsi di collegare entrambi i connettori. Note ! Modifica delle impostazioni di menu iniziali di questa unità. Vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 44. L’uscita subwoofer di questa unità è mono. ! Se si usa un subwoofer da 70 W (2 W), assicurarsi di collegarlo ai fili viola e viola/nero di questa unità. Non collegare niente ai fili verde e verde/nero. Amplificatore di potenza (venduto a parte) ! Consultare il rivenditore se l’installazione richiede la trapanatura di fori o altre modifiche del veicolo. ! Non installare questa unità se: — potrebbe interferire con il funzionamento del veicolo. — potrebbe procurare lesioni al passeggero in caso di arresto improvviso del veicolo. ! Se si surriscalda il laser a semiconduttore potrebbe subire danni. Non installare questa unità in luoghi soggetti a surriscaldamento, come in prossimità delle bocchette dell’impianto di riscaldamento. ! Le prestazioni ottimali si ottengono quando l’unità viene installata con un’angolazione inferiore a 60°. 60° Eseguire questi collegamenti quando si usa l’amplificatore opzionale. 3 1 5 2     4 5 1 Telecomando sistema Collegare al cavo Blu/bianco. 2 Amplificatore di potenza (venduto a parte) 3 Collegare con cavi RCA (venduti a parte) 4 All’uscita posteriore o del subwoofer 5 Altoparlanti posteriori o subwoofer Installazione Importante ! Controllare tutti i collegamenti e i sistemi prima dell’installazione finale. ! Non utilizzare componenti non approvati, poiché potrebbero provocare malfunzionamenti. ! Durante l’installazione, per assicurare la corretta dissipazione del calore quando si utilizza l’unità, accertarsi di lasciare ampio spazio dietro il pannello posteriore e avvolgere eventuali cavi allentati in modo che non ostruiscano le aperture. Lasciare ampio spazio 5 cm 5 cm 5cm cm ! Durante l’installazione utilizzare componenti disponibili in commercio. It <QRD3247-B> 46 Black plate (47,1) Sezione Installazione Installazione Come installare l’unità 1 2 Installare l’unità. Questa unità può essere installata correttamente utilizzando uno dei due metodi indicati di seguito. ! Installazione utilizzando il supporto ! Installazione utilizzando i fori delle viti ai lati dell’unità Installazione utilizzando i fori delle viti ai lati dell’unità % Fissare l’unità alla staffa di montaggio radio. Posizionare l’unità in modo che i fori per le viti sull’unità corrispondano ai fori per le viti sulla staffa, quindi serrare le viti in 3 posizioni su ciascun lato. Prima dell’installazione dell’unità 1 03 1 Rimuovere la guarnizione. 1 Supporto (componente montato in fabbrica) 1 Cruscotto 3 Italiano Installazione utilizzando il supporto Collocare la guarnizione. 1 Installare il supporto nel cruscotto. Dopo aver inserito il supporto nel cruscotto, scegliere e piegare le linguette in modo che corrispondano allo spessore del materiale del cruscotto. (Installare l’unità utilizzando le linguette superiori e inferiori in modo che sia fissata il più saldamente possibile. Per un montaggio sicuro, piegare le linguette a 90 gradi). 1 1 Guarnizione 1 2 1 2 Inserire le chiavi di estrazione fornite su entrambi i lati dell’unità fino a che non scattano in posizione. 1 1 Guarnizione 3 Rimozione del supporto 2 1 Cruscotto 2 Supporto (componente montato in fabbrica) 3 Estrarre l’unità dal supporto. Rimuovere il supporto. La procedura è analoga a quella descritta in Prima dell’installazione dell’unità. Per dettagli, vedere Prima dell’installazione dell’unità a pagina 47. 4 1 Quando la linguetta si inserisce nel foro, piegarla verso il basso. 2 Staffa di montaggio radio 3 Vite a testa tonda (5 mm × 8 mm) 4 Cruscotto o console It <QRD3247-B> 47 47 Black plate (48,1) Appendice Informazioni supplementari Risoluzione dei problemi In questo manuale i sintomi dei problemi sono riportati in testo grassetto, mentre le cause sono riportate in testo normale, non rientrato. Il testo normale, ma rientrato indica le azioni da intraprendere. Il display torna automaticamente alla visualizzazione normale. Non è stata eseguita alcuna operazione per 30 secondi. Eseguire nuovamente l’operazione. L’intervallo di riproduzione ripetuta cambia imprevedibilmente. A seconda dell’intervallo di riproduzione ripetuta, l’intervallo selezionato potrebbe cambiare quando si seleziona una cartella o un brano diverso, o quando si procede all’avanzamento rapido/modalità inversa. Selezionare nuovamente l’intervallo di riproduzione ripetuta. I brani di una sottocartella non vengono riprodotti. Non è possibile riprodurre i brani delle sottocartelle se è selezionata l’opzione FLD (ripetizione della cartella). Selezionare un altro intervallo di riproduzione ripetuta. Informazioni supplementari Malfunzionamento dell’unità. Ci sono interferenze. Si utilizza un dispositivo, come un telefono cellulare, che potrebbe provocare interferenze audio. Spostare il dispositivo elettrico che causa interferenze lontano dall’unità. Nel brano non è incorporata alcuna informazione di testo. Modificare la visualizzazione o riprodurre un altro brano/file. NO AUDIO Si è verificato un errore elettrico o meccanico. Spegnere e accendere il motore oppure passare a una sorgente diversa e poi di nuovo al lettore CD. Assenza di brani. Trasferire i file audio nel dispositivo di memoria USB e stabilire il collegamento. ERROR-15 Messaggi di errore Se si contatta il rivenditore o il Centro assistenza Pioneer più vicino, accertarsi di annotare il messaggio di errore. I messaggi di errore sono riportati in testo grassetto, mentre le cause sono riportate in testo normale, non rientrato. Il testo normale, ma rientrato indica le azioni da intraprendere. Il disco inserito è vuoto. Sostituire il disco. SKIPPED ERROR-23 Il dispositivo di memoria USB collegato contiene file protetti da tecnologia DRM. I file protetti vengono saltati. FORMAT READ PROTECT A volte si verifica ritardo tra quando la riproduzione viene avviata e quando si inizia a percepire il suono. Attendere che il messaggio scompaia. Tutti i file sul dispositivo di memoria USB collegato sono protetti da tecnologia DRM. Sostituire il dispositivo di memoria USB. AMP ERROR NO AUDIO N/A USB L’unità non funziona o l’altoparlante non è collegato correttamente; è stato attivato il circuito di protezione. Controllare il collegamento degli altoparlanti. Se il messaggio non scompare anche dopo aver disattivato e riattivato l’alimentazione, contattare il rivenditore o la stazione assistenza PIONEER più vicino. Il disco inserito non contiene file riproducibili. Sostituire il disco. Il dispositivo USB collegato non è supportato da questa unità. ! Collegare un dispositivo USB compatibile con lo standard MSC (Mass Storage Class). ! Scollegare il dispositivo e sostituirlo con un dispositivo di memoria USB compatibile. Problemi comuni SKIPPED Il disco inserito contiene file protetti con tecnologia DRM. I file protetti vengono saltati. PROTECT ERROR-07, 11, 12, 17, 30 Tutti i file nel disco inserito sono protetti da tecnologia DRM. Sostituire il disco. Il disco è sporco. Pulire il disco. Il disco è graffiato. Sostituire il disco. Dispositivo di memoria USB/iPod FORMAT READ A volte si verifica ritardo tra quando la riproduzione viene avviata e quando si inizia a percepire il suono. Attendere che il messaggio scompaia. 48 Il dispositivo di memoria USB collegato ha la protezione attivata. Seguire le istruzioni del dispositivo di memoria USB per disattivare la protezione. Il formato del CD non è supportato. Sostituire il disco. Lettore CD Quando cambia il display, viene visualizzata un’indicazione NO XXXX (ad esempio, NO TITLE). ERROR-07, 10, 11, 12, 15, 17, 30, A0 CHECK USB Il connettore USB o il cavo USB è in cortocircuito. Verificare che il connettore USB o il cavo USB non sia incastrato o danneggiato. CHECK USB Il dispositivo di memoria USB collegato consuma più della potenza massima consentita. Scollegare il dispositivo di memoria USB e non utilizzarlo. Portare l’interruttore della chiave di avviamento in posizione OFF, quindi su ACC o ON e infine collegare solo dispositivi di memoria USB compatibili. It <QRD3247-B> 48 Black plate (49,1) Appendice Informazioni supplementari Informazioni supplementari CHECK USB NOT FOUND L’iPod funziona correttamente ma non si ricarica. Accertarsi che il cavo di collegamento dell’iPod non sia in cortocircuito (ad esempio, bloccato da oggetti di metallo). Dopo aver verificato, portare l’interruttore della chiave di avviamento su OFF e quindi su ON, oppure scollegare l’iPod e collegarlo nuovamente. Non esistono brani correlati. Scaricare i brani sull’iPod. ERROR-19 START UP APP L’applicazione non è stata ancora avviata. Seguire le istruzioni visualizzate sullo schermo. Linee guida per l’uso corretto Dischi e lettori Utilizzare esclusivamente dischi che riportino uno dei due seguenti loghi. Errore dell’iPod. Scollegare il cavo dall’iPod. Quando viene visualizzato il menu principale dell’iPod, collegare l’iPod e reimpostarlo. Il dispositivo di memoria USB non è formattato in FAT12, FAT16 o FAT32. Il dispositivo di memoria USB deve essere formattato in FAT12, FAT16 o FAT32. ERROR-16 La versione del firmware dell’iPod è obsoleta. Aggiornare la versione dell’iPod. Errore dell’iPod. Scollegare il cavo dall’iPod. Quando viene visualizzato il menu principale dell’iPod, collegare l’iPod e reimpostarlo. I collegamenti tramite hub USB non sono supportati. Non attaccare etichette, non scrivere e non applicare prodotti chimici sulla superficie dei dischi. Non collegare dispositivi diversi dai dispositivi di memoria USB. Per pulire un CD, passare delicatamente un panno morbido sul disco procedendo dal centro verso l’esterno. Durante la guida fissare saldamente il dispositivo di memoria USB. Non lasciar cadere il dispositivo di memoria USB sul fondo della vettura, dove potrebbe incastrarsi sotto il pedale del freno o dell’acceleratore. La formazione di condensa potrebbe temporaneamente limitare le prestazioni del lettore. In tal caso, lasciarlo raggiungere una temperatura più alta per circa un’ora. Inoltre, pulire i dischi che dovessero presentare condensa con un panno morbido. La riproduzione dei dischi potrebbe non essere possibile a causa delle caratteristiche del disco, del formato del disco, dell’applicazione di registrazione, dell’ambiente di riproduzione, delle condizioni di conservazione e così via. Le asperità della strada possono far interrompere la riproduzione di un disco. ERROR-23 Utilizzare esclusivamente dischi convenzionali, completamente circolari. Se si utilizzano dischi sui quali è possibile applicare etichette, controllare le istruzioni e le avvertenze dei dischi. L’inserimento e l’espulsione potrebbe non riuscire, a seconda dei dischi. L’uso di dischi di questo tipo potrebbe danneggiare questa unità. Questa unità non può riprodurre i seguenti tipi di dischi: ! DualDisc ! Dischi da 8 cm: se si cerca di utilizzare tali dischi con un adattatore, potrebbero verificarsi malfunzionamenti dell’unità. ! Dischi di forma irregolare Non affiggere sui dischi etichette o altri materiali disponibili in commercio. ! I dischi potrebbero deformarsi e non sarà più possibile riprodurli. ! Le etichette potrebbero staccarsi durante la riproduzione, impedendo l’espulsione dei dischi. Ciò potrebbe danneggiare questa unità. Utilizzare dischi da 12 cm. Dispositivo di memoria USB Quando non si utilizzano, conservare i dischi nelle rispettive custodie. A seconda del dispositivo di memoria USB, potrebbero verificarsi i problemi seguenti. ! Le operazioni potrebbero risultare diverse. ! Il dispositivo di memoria potrebbe non essere riconosciuto. ! I file potrebbero non essere riprodotti correttamente. ! Il dispositivo potrebbe provocare interferenze audio mentre si ascolta la radio. Italiano Errore di comunicazione. Eseguire una delle operazioni riportate di seguito. –Portare l’interruttore della chiave di avviamento in posizione OFF e quindi di nuovo su ON. –Scollegare il dispositivo di memoria USB. –Passare a una sorgente diversa. Quindi, tornare alla sorgente USB. Applicazione Non toccare la superficie registrata dei dischi. iPod Non lasciare l’iPod in luoghi soggetti a temperature elevate. Durante la guida fissare saldamente l’iPod. Non lasciar cadere l’iPod sul fondo della vettura, dove potrebbe incastrarsi sotto il pedale del freno o dell’acceleratore. STOP Nessun brano presente nella lista corrente. Selezionare una lista che contenga brani. ! Dischi diversi da CD ! Dischi danneggiati, inclusi dischi crepati, scheggiati o piegati ! Dischi CD-R/RW non finalizzati It <QRD3247-B> 49 49 Black plate (50,1) Appendice Informazioni supplementari Informazioni sulle impostazioni dell’iPod ! Quando un iPod è collegato, questa unità disattiva la funzione EQ (equalizzatore) dell’iPod per ottimizzare l’acustica. Quando si scollega l’iPod, l’impostazione EQ ritorna al valore originale. ! Non è possibile disattivare l’opzione di ripetizione dell’iPod se il dispositivo viene utilizzato con questa unità. L’opzione di ripetizione viene automaticamente modificata su Tutti quando si collega l’iPod a questa unità. Se il testo salvato sull’iPod non è compatibile, non verrà visualizzato da questa unità. Compatibilità lista di riproduzione m3u: non compatibile File system: ISO 9660 di livello 1 e 2, Romeo, Joliet Bit di quantizzazione lineare: 8 e 16 (LPCM), 4 (MS ADPCM) Riproduzione multi-sessione: compatibile Trasferimento dati con scrittura a pacchetti: non compatibile Compatibilità iPod Frequenza di campionamento: da 16 kHz a 48 kHz (LPCM), 22,05 kHz e 44,1 kHz (MS ADPCM) Informazioni supplementari Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream con video: Non compatibile MP3 Estensione file: .mp3 Velocità in bit: da 8 kbps a 320 kbps (CBR), VBR Frequenza di campionamento: da 8 kHz a 48 kHz (32 kHz, 44,1 kHz, 48 kHz per l’enfatizzazione) Versioni tag ID3 compatibili: 1.0, 1.1, 2.2, 2.3, 2.4 (alla tag ID3 Versione 2.x viene data la priorità rispetto alla Versione 1.x.) Gerarchia delle cartelle riproducibili: fino a otto livelli (una gerarchia pratica non dovrebbe prevedere più di due livelli.) Cartelle riproducibili: fino a 99 WAV WMA Frequenza di campionamento: 32 kHz, 44,1 kHz, 48 kHz ATTENZIONE Estensione file: .wav Compatibilità MP3i (MP3 interattivo), mp3 PRO: non compatibile ! Non è possibile utilizzare questa funzione con l’opzione USB MTP. Velocità in bit: da 48 kbps a 320 kbps (CBR), da 48 kbps a 384 kbps (VBR) Disco ! Pioneer non garantisce la compatibilità con tutti i dispositivi di memoria USB e non si assume alcuna responsabilità per l’eventuale perdita di dati da lettori di file multimediali, smart phone o altri dispositivi anche se i dati vengono persi durante l’uso con questa unità. ! Non lasciare dischi o dispositivi di memoria USB in luoghi esposti ad alte temperature. Compatibilità audio compresso (dischi, USB) Estensione file: .wma 50 Informazioni supplementari Per i nomi dei file (incluse le estensioni) o i nomi delle cartelle, è possibile visualizzare esclusivamente i primi 32 caratteri. Il testo cirillico da visualizzare su questa unità deve essere codificato con uno dei seguenti set di caratteri: ! Unicode (UTF-8, UTF-16) ! Un set di caratteri diverso da Unicode utilizzato in ambiente Windows e impostato come cirillico nell’impostazione multilingue A seconda dell’applicazione utilizzata per codificare i file WMA, questa unità potrebbe non funzionare correttamente. In alcuni casi possono intercorrere alcuni istanti prima dell’avvio della riproduzione di file incorporati con dati immagine o file audio su dispositivi di memoria USB con numerose gerarchie di cartelle. File riproducibili: fino a 999 Indipendentemente dalla durata degli intervalli vuoti tra i brani della registrazione originale, i dischi contenenti file audio compresso verranno riprodotti con una breve pausa tra i brani. Dispositivo di memoria USB Gerarchia delle cartelle riproducibili: fino a otto livelli (una gerarchia pratica non dovrebbe prevedere più di due livelli.) Cartelle riproducibili: fino a 500 File riproducibili: fino a 15 000 Riproduzione dei file con protezione del copyright: non compatibile Dispositivo di memoria USB partizionato: verrà riprodotta solo la prima partizione riproducibile. In alcuni casi possono intercorrere alcuni istanti prima dell’avvio della riproduzione di file audio su un dispositivo di memoria USB con numerose gerarchie di cartelle. L’unità è compatibile esclusivamente con i seguenti modelli di iPod. Compatibile con ! iPod touch (di quinta generazione) ! iPod touch (di quarta generazione) ! iPod touch (di terza generazione) ! iPod touch (di seconda generazione) ! iPod touch (di prima generazione) ! iPod classic ! iPod con video ! iPod nano (di settima generazione) ! iPod nano (di sesta generazione) ! iPod nano (di quinta generazione) ! iPod nano (di quarta generazione) ! iPod nano (di terza generazione) ! iPod nano (di seconda generazione) ! iPod nano (di prima generazione) ! iPhone 5 ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone A seconda della generazione o della versione dell’iPod, alcune funzioni potrebbero non essere disponibili. Il funzionamento può variare a seconda della versione del software di iPod. It <QRD3247-B> 50 Black plate (51,1) Appendice Informazioni supplementari Gli utenti di iPod dotato di connettore Lightning devono utilizzare il cavo adattatore da Lightning a USB (fornito con l’iPod). Gli utenti di iPod dotato di connettore Dock devono utilizzare il cavo CD-IU51. Consultare il rivenditore per ulteriori dettagli. Per informazioni dettagliate sulla compatibilità di file/formati, vedere i manuali dell’iPod. Audiolibro, Podcast: compatibile Riproduzione in sequenza dei file audio Con questa unità, l’utente non può assegnare i numeri alle cartelle e specificare sequenze di riproduzione. Disco Copyright e marchi registrati La sequenza di selezione delle cartelle o altre operazioni potrebbero risultare differenti, a seconda del software utilizzato per la codifica o la scrittura. Dispositivo di memoria USB La sequenza di riproduzione è la stessa della sequenza di registrazione sul dispositivo di memoria USB. Per specificare la sequenza di riproduzione, si consiglia di utilizzare il seguente metodo. 1 Creare un nome file includendo i numeri che specificano la sequenza di riproduzione (ad esempio, 001xxx.mp3 e 099yyy.mp3). 2 Inserire tali file in una cartella. 3 Salvare la cartella contenente i file nel dispositivo di memoria USB. Tuttavia, a seconda dell’ambiente di sistema, potrebbe non essere possibile specificare la sequenza di riproduzione. Per i lettori audio portatili USB, la sequenza è diversa e dipende dal tipo di lettore. Tabella dei caratteri cirillici Esempio di gerarchia 01 02 1 2 03 3 4 04 5 6 05 Livello 1 Livello 2 Livello 3 Livello 4 : cartella : file audio compresso da 01 a 05: numero della cartella da 1 a 6: sequenza di riproduzione D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю D: Display C: Carattere MP3 La fornitura di questo prodotto prevede il trasferimento di una licenza esclusivamente per uso privato, non-commerciale e non prevede la concessione di una licenza, né implica qualsiasi diritto a utilizzare questo prodotto in qualsiasi trasmissione in diretta commerciale (ovvero, che generi profitti) terrestre, via satellite, cavo e/ o tramite altro mezzo, trasmissioni/diffusioni tramite Internet, Intranet e/o altre reti o in altri sistemi elettronici di distribuzione di contenuti, come applicazioni di trasmissione audio a pagamento o audio-on-demand. Per tali usi è necessaria una licenza specifica. Per dettagli, visitare http://www.mp3licensing.com. Italiano ATTENZIONE Pioneer non si assume alcuna responsabilità per l’eventuale perdita di dati dall’iPod, anche se i dati vengono persi durante l’uso di questa unità. Informazioni supplementari WMA Windows Media è un marchio di fabbrica o marchio di fabbrica depositato della Microsoft Corporation negli Stati Uniti ed in altri paesi. Questo prodotto include tecnologie di proprietà della Microsoft Corporation e non è utilizzbile senza licenza della Microsoft Licensing, Inc. iPod e iPhone iPhone, iPod, iPod classic, iPod nano, e iPod touch sono marchi di Apple Inc., registrati negli Stati Uniti e in altri Paesi. Lightning è un marchio di fabbrica di Apple Inc. “Fatto per l'iPod” e “Fatto per l'iPhone” significano che un accessorio elettronico è stato progettato specificamente rispettivamente per il collegamento con l'iPod o l'iPhone ed è stato certificato dal suo sviluppatore corrispondere agli standard operativi stabiliti da Apple. Apple non può essere considerata responsabile di questo dispositivo o della sua osservanza delle norme di sicurezza e dei vari regolamenti. Tenere presente che l'uso di questo accessorio con l'iPod o l'iPhone può peggiorare le prestazioni wireless. Androidä Android è un marchio di fabbrica di Google Inc. It <QRD3247-B> 51 51 Black plate (52,1) Appendice Informazioni supplementari Dati tecnici Generali Alimentazione .................. 14,4 V di c.c. (variazioni consentite da 10,8 V a 15,1 V) Negativa 10,0 A Messa a terra ................... Consumo massimo .......... Dimensioni (L × A × P): DIN Unità principale ............... Pannello anteriore ............ D Unità principale ............... Pannello anteriore ............ Peso ................................ 178 mm × 100 mm × 157 mm 188 mm × 118 mm × 25 mm 178 mm × 100 mm × 165 mm 170 mm × 96 mm × 17 mm 1,2 kg Audio Potenza d’uscita massima ................................... 50 W × 4 70 W × 1/2 W (per il subwoofer) Potenza d’uscita continua ................................... 22 W × 4 (da 50 Hz a 15 000 Hz, 5% THD, carico 4 W, entrambi i canali) Impedenza di carico ......... 4 W (variazioni consentite da 4 W a 8 W) Livello massimo di uscita ................................... 2,0 V Contorno della sonorità .... +10 dB (a 100 Hz), +6,5 dB (a 10 kHz) (volume: –30 dB) Equalizzatore (equalizzatore grafico a 5 bande): Frequenza ........................ 80 Hz/250 Hz/800 Hz/2,5 kHz/ 8 kHz Gamma di equalizzazione ................................... ±12 dB (a passi di 2 dB) Subwoofer (mono): Frequenze ........................ 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pendenza ......................... –12 dB per ottava, –24 dB per ottava Guadagno ........................ da +6 dB a –24 dB Fase ................................. Normale e invertita Lettore CD Sistema ........................... Sistema audio per compact disc Dischi utilizzabili .............. Compact disc Rapporto segnale/rumore ................................... 94 dB (a 1 kHz) (rete IEC-A) 52 Numero di canali ............. 2 (stereo) Formato di decodifica MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato di decodifica WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canali audio) (Windows Media Player) Formato segnale WAV ...... PCM lineare & MS ADPCM (Non compresso) USB Specifiche standard USB ................................... USB 2.0 massima velocità Alimentazione massima ... 1 A Classe USB ...................... MSC (Mass Storage Class) File system ....................... FAT12, FAT16, FAT32 Formato di decodifica MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato di decodifica WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canali audio) (Windows Media Player) Formato segnale WAV ...... PCM lineare & MS ADPCM (Non compresso) Sintonizzatore FM Gamma di frequenze ........ da 87,5 MHz a 108,0 MHz Sensibilità ........................ 9 dBf (0,8 µV/75 W, mono, rapporto S/R: 30 dB) Rapporto segnale/rumore ................................... 72 dB (rete IEC-A) Sintonizzatore MW Gamma di frequenze ........ da 531 kHz a 1 602 kHz Sensibilità ........................ 25 µV (rapporto S/R: 20 dB) Rapporto segnale/rumore ................................... 62 dB (rete IEC-A) Sintonizzatore LW Gamma di frequenze ........ da 153 kHz a 281 kHz Sensibilità ........................ 28 µV (rapporto S/R: 20 dB) Rapporto segnale/rumore ................................... 62 dB (rete IEC-A) Nota Caratteristiche tecniche e design sono soggetti a eventuali modifiche senza preavviso. It <QRD3247-B> 52 Black plate (53,1) Italiano It <QRD3247-B> 53 53 Black plate (54,1) Sección Antes de comenzar 01 Gracias por haber adquirido este producto PIONEER Lea con detenimiento este manual antes de utilizar el producto por primera vez para que pueda darle el mejor uso posible. Es muy importante que lea y cumpla con la información que aparece bajo los mensajes de ADVERTENCIA y PRECAUCIÓN de este manual. Una vez leído, guarde el manual en un lugar seguro y a mano para poder consultarlo en el futuro. Antes de comenzar Acerca de esta unidad Las frecuencias del sintonizador de esta unidad están asignadas para su uso en Europa Occidental, Asia, Oriente Próximo, África y Oceanía. El uso en otras áreas puede causar una recepción deficiente. La función RDS (sistema de datos de radio) opera sólo en áreas con emisoras de FM que trasmitan señales de RDS. ADVERTENCIA Si desea deshacerse de este producto, no lo mezcle con los residuos generales de su hogar. De conformidad con la legislación vigente, existe un sistema de recogida distinto para los productos electrónicos que requieren un procedimiento adecuado de tratamiento, recuperación y reciclado. Las viviendas privadas en los estados miembros de la UE, en Suiza y Noruega pueden devolver gratuitamente sus productos electrónicos usados en los centros de recolección previstos o bien en una tienda minorista (si adquieren un producto similar nuevo). En el caso de los países que no se han mencionado en el párrafo anterior, póngase en contacto con las autoridades locales a fin de conocer el método de eliminación correcto. Al actuar siguiendo estas instrucciones, se asegurará de que el producto eliminado se someta a los procesos de tratamiento, recuperación y reciclaje necesarios, evitando de este modo efectos potencialmente negativos en el entorno y la salud humana. 54 ! No trate de instalar o reparar este producto usted mismo. La instalación o la reparación de este producto por parte de personas sin cualificación ni experiencia en equipos electrónicos y accesorios para automóviles puede ser peligrosa y puede exponerle al riesgo de sufrir una descarga eléctrica u otros peligros. ! No intente utilizar la unidad mientras esté conduciendo. Asegúrese de salir de la carretera y aparcar su vehículo en un lugar seguro antes de intentar utilizar los controles del dispositivo. PRECAUCIÓN Este aparato es un producto de láser de clase 1 clasificado como tal en Seguridad de productos de láser, IEC 60825-1:2007. PRODUCTO LASER CLASE 1 En caso de problemas con el dispositivo Si esta unidad no funcionase correctamente, póngase en contacto con su concesionario o con el centro de servicio PIONEER autorizado más cercano. PRECAUCIÓN ! Evite que esta unidad entre en contacto con líquidos, ya que puede producir una descarga eléctrica. Además, el contacto con líquidos puede causar daños en la unidad, humo y recalentamiento. ! El CarStereo-Pass de Pioneer solo debe usarse en Alemania. ! Mantenga siempre el volumen lo suficientemente bajo como para poder escuchar los sonidos que provienen del exterior. ! Evite la exposición a la humedad. Es <QRD3247-B> 54 Black plate (55,1) Sección Durante el uso de la unidad Durante el uso de la unidad Unidad principal 1 2 PRECAUCIÓN 3 4 5 Utilice un cable USB Pioneer opcional (CDU50E) para conectar el dispositivo de almacenamiento USB, ya que cualquier dispositivo conectado directamente a la unidad sobresaldrá de ésta y podría resultar peligroso. a Indicaciones de la pantalla 2 1 6 7 1 h (expulsar) 2 iPod 89 4 5 6 7 9 8 b Aparece cuando existe un nivel, carpeta o menú inferior. a b cd a 1 1/ Ranura de carga de discos 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d 9 MULTI-CONTROL (M.C.) 6 a (parte posterior)/DIMMER (reductor de luz) 7 a 6/ (control de iPod) (lista) c Conector de entrada AUX (conector estéreo de 3,5 mm) d Puerto USB 2 b (lista) (control de iPod) La función iPod de la unidad se controlará desde el iPod. 3 Sección de información secundaria 4 TA (anuncios de tráfico) 5 TP (identificación de programa de tráfico) (recuperador de sonido) LOC (sintonización por búsqueda local) 8 (repetición) 9 (aleatorio) Menú de configuración LANGUAGE (idiomas múltiples) Esta unidad puede mostrar la información de texto de un archivo de audio comprimido incluso para aquella información integrada en inglés, ruso o turco. ! Si el idioma integrado y el idioma seleccionado no coinciden, puede que la información de texto no se muestre correctamente. ! Es posible que algunos caracteres no se visualicen correctamente. 1 Gire M.C. para seleccionar el ajuste deseado. ENG (Inglés)—РУС (Ruso)—TUR (Turco) 2 Pulse M.C. para confirmar la selección. CLOCK SET (ajuste del reloj) 1 Una vez instalada la unidad, gire la llave de encendido hasta la posición ON. Aparecerá SET UP. 1 2 3 4 2 FM STEP (paso de sintonía de FM) Pulse M.C. para cambiar a YES. # El menú de configuración desaparece si no utiliza la unidad durante 30 segundos. # Si prefiere dejar la configuración para más tarde, gire M.C. para cambiar a NO. 3 Pulse M.C. para seleccionarlo. 4 Para configurar el menú, siga estos pasos. Para avanzar a la siguiente opción del menú debe confirmar primero su selección. Gire M.C. para ajustar la hora. Presione M.C. para seleccionar el minuto. Gire M.C. para ajustar el minuto. Pulse M.C. para confirmar la selección. Utilice FM STEP para ajustar las opciones de paso de sintonía FM (ajustes del paso de búsqueda). 1 Gire M.C. para seleccionar el paso de sintonía de FM. 100 (100 kHz)—50 (50 kHz) 2 Pulse M.C. para confirmar la selección. Aparecerá QUIT. ! El paso de sintonía manual está fijado en 50 kHz. ! Cuando se desactivan AF y TA, el paso de búsqueda se fija en 50 kHz incluso si está ajustado en 100. Español 3 4 b 3 Sección de información principal ! Sintonizador: banda y frecuencia ! RDS: nombre del servicio del programa, información PTY y otro tipo de información de texto ! Reproductor de CD, dispositivo de almacenamiento USB y iPod: tiempo de reproducción transcurrido e información de texto 02 5 Para cerrar la configuración, gire M.C. y seleccione YES. # Si prefiere volver a cambiar la configuración, gire M.C. para cambiar a NO. 6 Pulse M.C. para seleccionarlo. Es <QRD3247-B> 55 55 Black plate (56,1) Sección Durante el uso de la unidad 02 Notas ! Se pueden configurar las opciones del menú desde el menú del sistema y desde el menú de inicio. Si desea más información sobre los ajustes, consulte Menú del sistema en la página 61 y Menú inicial en la página 62. ! Si desea cancelar el menú de configuración, pulse SRC/OFF. Funcionamiento básico Encendido de la unidad 1 Pulse SRC/OFF para encender la unidad. Apagado de la unidad 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. Selección de una fuente 1 Pulse SRC/OFF para desplazarse entre: RADIO—CD—USB/iPod—APP (aplicación)— AUX ! Se muestra USB MTP mientras está en uso la conexión MTP. ! Si hay un iPod conectado y se selecciona una fuente diferente a iPod, se podrá cambiar a iPod pulsando iPod. Ajuste del volumen 1 Gire M.C. para ajustar el volumen. Nota Si el cable azul/blanco de esta unidad está conectado al terminal de control del relé de la antena automática del vehículo, la antena se extenderá cuando se encienda el equipo. Para retraer la antena, apague la fuente. 56 Durante el uso de la unidad Operaciones del menú utilizadas frecuentemente Retorno a la visualización anterior Para volver a la lista anterior (la carpeta de un nivel superior) 1 Pulse /DIMMER. Retorno a la visualización normal Acceso al menú principal 1 Pulse BAND/ . Retorno a la visualización normal desde la lista 1 Pulse BAND/ . Radio Funcionamiento básico Selección de una banda 1 Pulse BAND/ hasta que se visualice la banda deseada (FM1, FM2, FM3 para FM o MW/LW). Cambio de emisoras presintonizadas 1 Pulse c o d. ! Para utilizar esta función, seleccione PCH (canal presintonizado) en SEEK. Sintonización manual (paso a paso) 1 Pulse c o d. ! Para utilizar esta función, seleccione MAN (sintonización manual) en SEEK. Búsqueda 1 Mantenga pulsado c o d y luego suéltelo. Se puede cancelar la sintonización por búsqueda pulsando brevemente c o d. Mientras mantiene pulsado c o d se pueden saltar las emisoras. La sintonización por búsqueda comienza inmediatamente después de que suelte c o d. Notas ! Para obtener detalles sobre SEEK, consulte SEEK (ajuste tecla izquierda/derecha) en la página 57. ! Se puede activar y desactivar la función AF (búsqueda de frecuencias alternativas) de esta unidad; se debe desactivar la función AF para la sintonización normal (consulte AF (búsqueda de frecuencias alternativas) en la página 57). Almacenamiento y recuperación de emisoras para cada banda Uso de los botones de ajuste de presintonías 1 Para guardar: mantenga pulsado uno de los botones de ajuste de presintonías (1/ a 6/ ) hasta que el número deje de parpadear. 2 Para recuperar emisoras: pulse uno de los botones de ajuste de presintonías (1/ a 6/ ). Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! FREQUENCY (nombre del servicio de programa o frecuencia) ! BRDCST INFO (nombre del servicio de programa/información PTY) ! CLOCK (nombre de la fuente y reloj) Notas ! Si no se puede adquirir el nombre del servicio de programa en FREQUENCY, se visualizará la frecuencia en su lugar. Si se detecta el nombre del servicio de programa, se visualizará el nombre del servicio de programa. ! Dependiendo de la banda, puede cambiarse la información de texto. ! Los elementos de información de texto pueden cambiar según la zona. Uso de las funciones PTY Se puede sintonizar una emisora utilizando la información PTY (tipo de programa). Búsqueda de una emisora RDS por información PTY (lista). 1 Pulse 2 Gire M.C. para seleccionar el tipo de programa. NEWS/INFO—POPULAR—CLASSICS—OTHERS 3 Pulse M.C. para comenzar la búsqueda. La unidad busca una emisora que transmita ese tipo de programa, cuando la encuentra, se visualiza el nombre del servicio de programa. ! Para cancelar la búsqueda, vuelva a pulsar M.C. ! El programa de algunas emisoras puede ser distinto al programa indicado por el PTY transmitido. ! Si ninguna emisora está transmitiendo el tipo de programa que busca, se visualizará NOT FOUND durante unos dos segundos y el sintonizador volverá a la emisora original. Lista PTY Para obtener más detalles sobre la lista PTY, visite la siguiente página web: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Ajustes de funciones 1 Pulse M.C. para acceder al menú principal. Es <QRD3247-B> 56 Black plate (57,1) Sección Durante el uso de la unidad 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. 3 Gire M.C. para seleccionar la función. Una vez seleccionado, se pueden ajustar las siguientes funciones. # Si se selecciona la banda MW/LW, solo estarán disponibles BSM, LOCAL y SEEK. FM SETTING (ajustes de calidad de sonido FM) Durante el uso de la unidad La sintonización por búsqueda local le permite sintonizar sólo las emisoras de radio con señales lo suficientemente intensas como para asegurar una correcta recepción. 1 Pulse M.C. para seleccionar el ajuste deseado. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 El ajuste de nivel superior solo permite recibir las emisoras con las señales más intensas, mientras que los ajustes más bajos permiten recibir las emisoras con señales más débiles. AF (búsqueda de frecuencias alternativas) BSM (memoria de las mejores emisoras) 1 Pulse M.C. para activar o desactivar la función NEWS. BSM (memoria de las mejores emisoras) guarda automáticamente las seis emisoras más fuertes ordenadas por la intensidad de la señal. 1 Pulse M.C. para activar la función BSM. Para cancelar, vuelva a pulsar M.C. REGIONAL (regional) Cuando se usa la función AF, la función regional limita la selección de las emisoras a aquellas que transmiten programas regionales. 1 Pulse M.C. para activar o desactivar la función regional. LOCAL (sintonización por búsqueda local) Conexión MTP Los dispositivos Android compatibles con MTP (al ejecutar el sistema operativo Android 4.0 o superior) se pueden conectar a través de la conexión MTP utilizando la fuente USB. Para conectar un dispositivo Android, utilice el cable suministrado con el dispositivo. TA (espera por anuncio de tráfico) Nota Esta función no es compatible con WAV. 1 Pulse M.C. para activar o desactivar la espera por anuncio de tráfico. Funcionamiento básico 1 Pulse M.C. para activar o desactivar la función AF. NEWS (interrupción por programa de noticias) SEEK (ajuste tecla izquierda/derecha) Es posible asignar funciones a las teclas derecha e izquierda de la unidad. Seleccione MAN (sintonización manual) para subir o bajar la frecuencia de forma manual o seleccione PCH (canales presintonizados) para cambiar entre los canales presintonizados. 1 Presione M.C. para seleccionar MAN o PCH. Reproducción de un CD/CD-R/CD-RW 1 Inserte el disco en la ranura de carga de discos con el lado de la etiqueta hacia arriba. Expulsión de un CD/CD-R/CD-RW 1 Pulse h. Reproducción de canciones de un dispositivo de almacenamiento USB 1 Abra la tapa del puerto USB. 2 Conecte el dispositivo de almacenamiento USB mediante un cable USB. Detención de la reproducción de archivos en un dispositivo de almacenamiento USB 1 Puede desconectar el dispositivo de almacenamiento USB en cualquier momento. Selección de una carpeta 1 Pulse 1/ o 2/ . Selección de una pista 1 Pulse c o d. Avance rápido o retroceso 1 Mantenga pulsado c o d. ! Al reproducir audio comprimido, no hay sonido durante el avance rápido o el retroceso. Regreso a la carpeta raíz 1 Mantenga pulsado BAND/ . Cambio entre audio comprimido y CD-DA 1 Pulse BAND/ . Cambio entre dispositivos de memoria de reproducción Se puede cambiar entre dispositivos de memoria de reproducción en dispositivos de almacenamiento USB con más de un dispositivo de memoria compatible con uno de almacenamiento masivo. 1 Pulse BAND/ . ! Se puede cambiar hasta 32 dispositivos de memoria diferentes. Nota Desconecte los dispositivos de almacenamiento USB de la unidad cuando no los utilice. Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: CD-DA ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) CD-TEXT ! TRACK INFO (título de la pista/artista de la pista/título del disco) ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) MP3/WMA/WAV ! TRACK INFO (título de la pista/nombre del artista/título del álbum) ! FILE INFO (nombre del fichero/nombre de la carpeta) ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) Es <QRD3247-B> 57 Español Puede ajustar el nivel de calidad del sonido para que coincida con las condiciones de las señales de emisión de la señal de banda FM. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ajuste deseado. ! STANDARD – Es el ajuste estándar. ! HI-FI – Es el ajuste que debe utilizar para dar prioridad a la alta calidad del sonido estéreo. ! STABLE – Es el ajuste que debe utilizar para dar prioridad al ruido bajo del sonido monoaural. CD/CD-R/CD-RW y dispositivos de almacenamiento USB 02 57 Black plate (58,1) Sección Durante el uso de la unidad 02 Selección y reproducción de archivos/pistas de la lista de nombres 1 Pulse para cambiar al modo de lista por nombre de archivo/pista. 2 Utilice M.C. para seleccionar el nombre del archivo deseado (o de la carpeta). Selección de un archivo o una carpeta 1 Gire M.C. Reproducción 1 Tras seleccionar un archivo o una pista, pulse M.C. Visualización de una lista de los archivos (o las carpetas) de la carpeta seleccionada 1 Tras seleccionar una carpeta, pulse M.C. Reproducción de una canción de la carpeta seleccionada 1 Tras seleccionar una carpeta, mantenga pulsado M.C. Durante el uso de la unidad Operaciones con botones especiales Selección de un intervalo de repetición de reproducción 1 Pulse 6/ para desplazarse entre las siguientes opciones: CD/CD-R/CD-RW ! ALL – Repite todas las pistas ! ONE – Repite la pista actual ! FLD – Repite la carpeta actual Dispositivo de almacenamiento USB ! ALL – Repite todos los archivos ! ONE – Repite el archivo actual ! FLD – Repite la carpeta actual Reproducción de las pistas en orden aleatorio para activar o desactivar la repro1 Pulse 5/ ducción aleatoria. Las pistas de una gama de repetición seleccionada se reproducen en orden aleatorio. ! Para cambiar de canciones durante la reproducción aleatoria, pulse d para cambiar a la pista siguiente; si se pulsa c se reiniciará la reproducción de la pista actual desde el principio de la canción. Pausa de la reproducción 1 Pulse 4/PAUSE para pausar o reanudar. Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) 1 Pulse 3/S.Rtrv para desplazarse entre: 1—2—OFF (desactivado) 1 es efectivo para tasas de compresión baja, y 2 para tasas de compresión alta. Ajustes de funciones 1 Pulse M.C. para acceder al menú principal. 58 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. Una vez seleccionado, se puede ajustar la función de abajo. S.RTRV (recuperador de sonido) Mejora automáticamente el audio comprimido y restaura el sonido óptimo. 1 Pulse M.C. para seleccionar el ajuste deseado. Para obtener más información, consulte Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) en la página 58. Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! TRACK INFO (título de la pista/nombre del artista/título del álbum) ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) Para buscar una canción iPod 1 Para ir al menú superior de la búsqueda de listas, pulse . Funcionamiento básico Reproducción de canciones en un iPod 1 Abra la tapa del puerto USB. 2 Conecte un iPod a la entrada USB. La reproducción se inicia automáticamente. 2 Utilice M.C. para seleccionar una categoría/canción. Selección de una canción (capítulo) 1 Pulse c o d. Cambio del nombre de la canción o la categoría 1 Gire M.C. Listas de reproducción—artistas—álbumes— canciones—podcasts—géneros—compositores—audiolibros Selección de un álbum 1 Pulse 1/ o 2/ . Reproducción 1 Tras seleccionar una canción, pulse M.C. Avance rápido o retroceso 1 Mantenga pulsado c o d. Visualización de una lista de canciones de la categoría seleccionada 1 Tras seleccionar una categoría, pulse M.C. Notas ! El iPod no puede encenderse o apagarse cuando el modo de control está ajustado en CTRL AUDIO. ! Desconecte los auriculares del iPod antes de conectarlo a esta unidad. ! El iPod se apagará aproximadamente dos minutos después de que la llave de encendido del automóvil se ponga en OFF. Es <QRD3247-B> 58 Black plate (59,1) Sección Durante el uso de la unidad Reproducción de una canción de la categoría seleccionada 1 Tras seleccionar una categoría, mantenga pulsado M.C. Búsqueda alfabética en las listas 1 Cuando se visualice una lista de la categoría para cambiar al modo seleccionada, pulse de búsqueda alfabética. ! Es posible cambiar al modo de búsqueda por orden alfabético girando M.C. dos veces. 2 Haga girar M.C. para seleccionar una letra. 3 Pulse M.C. para visualizar la lista alfabética. ! Para cancelar la búsqueda, pulse /DIMMER. Operaciones con botones especiales Selección de un intervalo de repetición de reproducción 1 Pulse 6/ para desplazarse entre las siguientes opciones: ! ONE – Repite la canción actual ! ALL – Repite todas las canciones de la lista seleccionada ! Cuando el modo de control se ha ajustado en CTRL iPod, el intervalo de repetición de reproducción será el mismo que el que se ajustó para el iPod conectado. Selección de un intervalo de reproducción aleatorio (shuffle) para desplazarse entre las si1 Pulse 5/ guientes opciones: ! SNG – Reproduce canciones siguiendo un orden aleatorio dentro de la lista. ! ALB – Reproduce canciones siguiendo un orden aleatorio dentro del álbum. ! OFF – No se reproduce en orden aleatorio. Reproducción de todas las canciones en orden aleatorio (shuffle all) para activar la 1 Mantenga presionado 5/ función de reproducción de todas las canciones en orden aleatorio (shuffle all). ! Para desactivar la reproducción de todas las canciones en orden aleatorio, seleccione OFF en reproducción aleatoria. Para más información, consulte Selección de un intervalo de reproducción aleatorio (shuffle) en la página 59. Pausa de la reproducción 1 Pulse 4/PAUSE para pausar o reanudar. Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) 1 Pulse 3/S.Rtrv para desplazarse entre: 1—2—OFF (desactivado) 1 es efectivo para tasas de compresión baja, y 2 para tasas de compresión alta. Reproducción de canciones relacionadas con la canción que se está reproduciendo Se pueden reproducir canciones de las siguientes listas: • Lista de álbumes del artista que se está reproduciendo • Lista de canciones del álbum que se está reproduciendo • Lista de álbumes del género que se está reproduciendo 1 Mantenga pulsado para cambiar al modo de reproducción de enlace. 2 Haga girar M.C. para cambiar el modo y pulse para seleccionarlo. ! ARTIST – Reproduce un álbum del artista que se está reproduciendo. ! ALBUM – Reproduce una canción del álbum que se está reproduciendo. ! GENRE – Reproduce un álbum del género que se está reproduciendo. La canción o el álbum seleccionado se reproducirá después de la canción que se esté reproduciendo en ese momento. Notas ! Se puede cancelar la canción o el álbum seleccionado mediante funciones diferentes a la búsqueda de enlace (p. ej., avance rápido y retroceso). ! Según la canción seleccionada, pueden cortarse el final de la canción que se esté reproduciendo o el principio de la canción o del álbum seleccionados. Uso de la función iPod de la unidad desde el iPod La función iPod de esta unidad se puede controlar desde el iPod conectado. 02 CTRL iPod no es compatible con los siguientes modelos de iPod: ! iPod nano 1ª generación ! iPod con vídeo % Pulse BAND/ control. para cambiar el modo de ! CTRL iPod – La función iPod de esta unidad se puede utilizar desde el iPod conectado. ! CTRL AUDIO – La función iPod de esta unidad se puede controlar desde esta unidad. También puede cambiar el ajuste de salida presionando iPod. Notas ! Al cambiar el modo de control a CTRL iPod, se pausa la reproducción de la canción. Utilice el iPod para reanudar la reproducción. ! Las siguientes operaciones estarán disponibles en esta unidad aunque se ajuste el modo de control en CTRL iPod. — Pausa — Avance rápido/retroceso — Selección de una canción (capítulo) Español Notas ! Es posible reproducir listas de reproducción creadas con el programa de ordenador (MusicSphere). Dicho programa estará disponible en nuestro sitio web. ! Las listas de reproducción creadas con el programa de ordenador (MusicSphere) se muestran de forma abreviada. Durante el uso de la unidad ! El volumen solo se puede controlar desde esta unidad. Ajustes de funciones 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. 3 Gire M.C. para seleccionar la función. Una vez seleccionado, se pueden ajustar las siguientes funciones. ! AUDIO BOOK no está disponible cuando se selecciona CTRL iPod en modo de control. Para más información, consulte Uso de la función iPod de la unidad desde el iPod en la página 59. Es <QRD3247-B> 59 59 Black plate (60,1) Sección Durante el uso de la unidad 02 AUDIO BOOK (velocidad del audiolibro) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar su ajuste favorito. ! FASTER – Reproducción con velocidad superior a la normal ! NORMAL – Reproducción con velocidad normal ! SLOWER – Reproducción con velocidad inferior a la normal S.RTRV (recuperador de sonido) 1 Pulse M.C. para seleccionar el ajuste deseado. Para obtener más información, consulte Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) en la página 59. Uso de las aplicaciones del dispositivo conectado Puede utilizar la unidad para reproducir y controlar las pistas en aplicaciones de iPhone o simplemente para reproducir música. Durante el uso de la unidad Importante El uso de aplicaciones de terceros puede implicar o necesitar la puesta a disposición de información de identificación personal, bien mediante la creación de una cuenta de usuario o de algún otro modo, y, para ciertas aplicaciones, la puesta a disposición de datos de geoubicación. TODAS LAS APLICACIONES DE TERCEROS SON RESPONSABILIDAD EXCLUSIVA DE LOS PROVEEDORES, INCLUIDAS SIN LIMITACIÓN LA RECOPILACIÓN Y LA SEGURIDAD DE LOS DATOS DE USUARIO Y LAS PRÁCTICAS DE PRIVACIDAD. AL ACCEDER A APLICACIONES DE TERCEROS, USTED SE MANIFIESTA DE ACUERDO EN REVISAR LOS TÉRMINOS DE SERVICIO Y LAS POLÍTICAS DE PRIVACIDAD DE LOS PROVEEDORES. SI NO ESTÁ DE ACUERDO CON LOS TÉRMINOS O LAS POLÍTICAS DE ALGÚN PROVEEDOR O NO CONSIENTE EL USO DE DATOS DE GEOUBICACIÓN DONDE SEA APLICABLE, NO UTILICE ESTAS APLICACIONES DE TERCEROS. Información acerca de la compatibilidad de dispositivos conectados A continuación se muestra información detallada acerca de las terminales necesarias para utilizar la aplicación para iPhone en esta unidad. Para usuarios de iPhone ! Esta función es compatible tanto con iPhone como con iPod touch. ! El dispositivo tiene un iOS 5.0 o superior. Notas ! Compruebe en nuestra página web la lista de las aplicaciones de iPhone compatibles con esta unidad. 60 ! Pioneer no se responsabiliza de cualquier problema que pueda surgir a causa de un contenido incorrecto o defectuoso de la aplicación. ! El contenido y funcionamiento de las aplicaciones compatibles son responsabilidad de los proveedores de las mismas. Ajustes de funciones Procedimiento de inicio para usuarios de iPhone 3 Gire M.C. para seleccionar la función. Una vez seleccionado, se pueden ajustar las siguientes funciones. 1 Conecte un iPhone a una salida USB. 2 Cambie la fuente a APP. 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. PAUSE (pausar) 3 Inicie la aplicación en el iPhone e inicie la reproducción. Funcionamiento básico Selección de una pista 1 Pulse c o d. 1 Pulse M.C. para pausar o reanudar. S.RTRV (recuperador de sonido) 1 Pulse M.C. para seleccionar el ajuste deseado. 1—2—OFF (desactivado) 1 es efectivo para tasas de compresión baja, y 2 para tasas de compresión alta. Avance rápido o retroceso 1 Mantenga pulsado c o d. Ajustes de audio Pausa de la reproducción 1 Pulse BAND/ para pausar o reanudar. 1 Pulse M.C. para acceder al menú principal. Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! TRACK INFO (título de la pista/nombre del artista/título del álbum) ! APP NAME (nombre de la aplicación) ! ELAPSED TIME (tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar AUDIO. 3 Gire M.C. para seleccionar la función de audio. Una vez seleccionado, se pueden ajustar las siguientes funciones de audio. ! FADER no está disponible cuando se selecciona SUB.W/SUB.W en SP-P/O MODE. Para más información, consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página 62. Es <QRD3247-B> 60 Black plate (61,1) Sección Durante el uso de la unidad ! SUB.W y SUB.W CTRL no están disponibles cuando se selecciona REAR/REAR en SP-P/O MODE. Para más información, consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página 62. ! SUB.W CTRL no está disponible cuando se selecciona SUB.W en OFF. Para más información, consulte SUB.W (ajuste de subgraves activado/desactivado) en la página 61. ! SLA no está disponible si se ha seleccionado FM como fuente. FADER (ajuste de ecualizador) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el balance entre los altavoces delanteros/traseros. BALANCE (ajuste del balance) EQ SETTING (recuperación de ecualizador) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ecualizador. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La banda y el nivel de ecualización se pueden personalizar si se selecciona CUSTOM1 o CUSTOM2. Si selecciona CUSTOM1 o CUSTOM2, complete los pasos que se describen más abajo. Si selecciona otras opciones, pulse M.C. para volver a la pantalla anterior. ! CUSTOM1 se puede ajustar por separado para cada fuente; no obstante, USB, iPod y APP se ajustan igual automáticamente. ! CUSTOM2 es una configuración compartida que se utiliza para todas las fuentes. 3 Pulse M.C. para mostrar el modo de ajuste. 4 Pulse M.C. para desplazarse entre las siguientes opciones: Banda de ecualización—Nivel de ecualización 5 Gire M.C. para seleccionar el ajuste deseado. Banda de ecualización: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Nivel de ecualización: +6 a –6 LOUDNESS (sonoridad) La sonoridad compensa las deficiencias en los intervalos de frecuencias bajas y altas cuando se escucha a un volumen bajo. 1 Pulse M.C. para seleccionar el ajuste deseado. OFF (desactivado)—LOW (bajo)—MID (medio)—HI (alto) SUB.W (ajuste de subgraves activado/desactivado) Esta unidad está equipada con una salida de subgraves que se puede activar o desactivar. 1 Pulse M.C. para seleccionar el ajuste deseado. NOR (fase normal)—REV (fase inversa)—OFF (subgraves desactivados) SUB.W CTRL (ajuste de subgraves) Solo las frecuencias más bajas que aquellas en el intervalo seleccionado se generan por el altavoz de subgraves. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para desplazarse entre las siguientes opciones: Frecuencia de corte—Nivel de salida—Nivel de pendiente Las tasas que se puedan ajustar parpadearán. 3 Gire M.C. para seleccionar el ajuste deseado. Frecuencia de corte: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Nivel de salida: de –24 a +6 Nivel de pendiente: –12— –24 02 SLA (ajuste del nivel de fuente) Esta función evita que el volumen cambie demasiado drásticamente cuando se cambia de fuente. ! Los ajustes se basan en el nivel de volumen de FM, que se mantiene inalterado. ! El nivel del volumen de MW/LW también se puede ajustar con esta función. ! USB, iPod y APP reciben el mismo ajuste automáticamente. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el volumen de la fuente. Gama de ajuste: de +4 a –4 BASS BOOST (intensificación de graves) Menú del sistema 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el nivel que desee. Se visualiza 0 a +6 mientras se aumenta o disminuye el nivel. Importante PW SAVE (ahorro de energía) se cancela si la batería del vehículo se desconecta, y se debe activar de nuevo cuando se vuelva a conectar la batería. Dependiendo de los métodos de conexión, cuando PW SAVE (ahorro de energía) está desactivado, la unidad puede seguir obteniendo energía de la batería si la llave de encendido de su vehículo no tiene posición ACC (accesorio). HPF SETTING (ajuste del filtro de paso alto) Utilice esta función si desea escuchar solo sonidos de alta frecuencia. Solamente se emiten por los altavoces frecuencias más altas que el corte del filtro de paso alto (HPF). 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para desplazarse entre las siguientes opciones: Frecuencia de corte—Nivel de pendiente 3 Gire M.C. para seleccionar el ajuste deseado. Frecuencia de corte: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Nivel de pendiente: –12— –24 Español 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el balance de los altavoces izquierdo o derecho. Durante el uso de la unidad 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. 3 Gire M.C. para seleccionar la función del menú del sistema. Una vez seleccionado, se pueden ajustar las siguientes funciones del menú de sistema. LANGUAGE (idiomas múltiples) 1 Pulse M.C. para seleccionar el ajuste deseado. ENG (Inglés)—РУС (Ruso)—TUR (Turco) CLOCK SET (ajuste del reloj) Es <QRD3247-B> 61 61 Black plate (62,1) Sección Durante el uso de la unidad 02 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para seleccionar el segmento de la pantalla del reloj que desea ajustar. Hora—Minuto 3 Gire M.C. para ajustar el reloj. 12H/24H (anotación de la hora) 1 Pulse M.C. para seleccionar el ajuste deseado. 12H (reloj de 12 horas)—24H (reloj de 24 horas) AUTO PI (búsqueda PI automática) La unidad puede buscar automáticamente una emisora diferente con el mismo programa, incluso durante la recuperación de emisoras presintonizadas. 1 Pulse M.C. para activar o desactivar la función de búsqueda PI automática. AUX (entrada auxiliar) Active este ajuste si utiliza un dispositivo auxiliar conectado a esta unidad. 1 Pulse M.C. para activar o desactivar AUX. DIMMER (atenuador de luz) 1 Pulse M.C. para activar o desactivar el atenuador de luz. ! También se puede cambiar la configuración de atenuador de luz manteniendo pulsado /DIMMER. MUTE MODE (modo de silencio) El sonido proveniente de este sistema se silencia o atenúa automáticamente cuando se recibe una señal desde un equipo con función de silenciamiento. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ajuste deseado. ! MUTE – Silenciamiento ! 20dB ATT – Atenuación (20dB ATT tiene un efecto más potente que 10dB ATT) ! 10dB ATT – Atenuación 62 Durante el uso de la unidad PW SAVE (ahorro de energía) La activación de esta función le permite reducir el consumo de la batería. ! Cuando esta función está activada, la única operación que se permite es el encendido de la fuente. 1 Pulse M.C. para activar o desactivar el ahorro de energía. Menú inicial 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. 2 Mantenga pulsado SRC/OFF hasta que aparezca el menú principal en la pantalla. 3 Gire M.C. para cambiar la opción de menú y pulse para seleccionar INITIAL. 4 Gire M.C. para seleccionar la función del menú de inicio. Una vez seleccionado, se pueden ajustar las siguientes funciones del menú inicial. SP-P/O MODE (ajuste de la salida posterior y del preamplificador) La salida de cables de altavoces traseros y la salida RCA de esta unidad se puede usar para conectar altavoces de gama completa o de subgraves. Seleccione la opción adecuada para su conexión. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ajuste deseado. ! REAR/SUB.W – Seleccione cuando haya conectado un altavoz de gama completa a la salida de cables de altavoces traseros y un subgrave a la salida RCA. ! SUB.W/SUB.W – Seleccione cuando haya conectado un subgrave directamente a la salida de cables de altavoces traseros, sin ningún amplificador auxiliar, y un subgrave a la salida RCA. ! REAR/REAR – Seleccione cuando exista un altavoz de gama completa conectado a la salida de cables de los altavoces traseros y a la salida RCA. Si hay un altavoz de gama completa conectado a la salida de cables de los altavoces traseros y la salida RCA no se utiliza, podrá seleccionar REAR/SUB.W o REAR/REAR. Uso de una fuente AUX 1 Inserte el miniconector estéreo en el conector de entrada AUX. 2 Pulse SRC/OFF para seleccionar AUX como fuente. Nota No se puede seleccionar AUX si no se activa el ajuste auxiliar. Para obtener más información, consulte AUX (entrada auxiliar) en la página 62. Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! Nombre de la fuente ! Nombre de la fuente y reloj Si aparece un display no deseado Desactive el display no deseado mediante los pasos que se indican a continuación. FM STEP (paso de sintonía de FM) 1 Pulse M.C. para seleccionar el paso de sintonía de FM. 100 (100 kHz)—50 (50 kHz) Menú del sistema 1 Pulse M.C. para acceder al menú principal. 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. 2 Mantenga pulsado SRC/OFF hasta que aparezca el menú principal en la pantalla. 3 Gire M.C. para visualizar DEMO OFF y púlselo para realizar la selección. 3 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. 4 Pulse M.C. para cambiar a YES. 5 Pulse M.C. para seleccionarlo. 4 Gire M.C. para seleccionar la función del menú del sistema. Para obtener más información, consulte Menú del sistema en la página 61. Es <QRD3247-B> 62 Black plate (63,1) Sección Instalación Instalación Conexiones F O N OF Importante ! Cuando esta unidad se instale en un vehículo sin posición ACC (accesorio) en la llave de encendido, el cable rojo se debe conectar al terminal que pueda detectar la operación de la llave de encendido. De lo contrario, puede descargarse la batería. STAR T Posición ACC Sin posición ACC ! El uso de esta unidad en unas condiciones distintas de las indicadas a continuación podría causar incendios o fallos de funcionamiento. ! Para evitar cortocircuitos, sobrecalentamiento o fallos de funcionamiento, asegúrese de seguir las siguientes instrucciones. — Desconecte el terminal negativo de la batería antes de la instalación. — Asegure el cableado con pinzas para cables o cinta adhesiva. Envuelva con cinta adhesiva las partes en contacto con piezas metálicas para proteger el cableado. — Mantenga los cables alejados de las partes móviles, como la palanca de cambios y los raíles de los asientos. — Coloque todos los cables alejados de lugares calientes, como cerca de la salida del calefactor. — No conecte el cable amarillo a la batería pasándolo a través del orificio hasta el compartimiento del motor. — Cubra con cinta aislante los conectores de cables que queden desconectados. — No acorte ningún cable. ! Cuando se enciende esta unidad, se emite una señal de control a través del cable azul/ blanco. Conecte este cable al mando a distancia del sistema de un amplificador de potencia externo o al terminal de control del relé de la antena automática del vehículo (máx. 300 mA 12 V cc). Si el vehículo posee una antena integrada en el cristal del parabrisas, conéctela al terminal de la fuente de alimentación del amplificador de la antena. ! Nunca conecte el cable azul/blanco al terminal de potencia de un amplificador de potencia externo, ni al terminal de potencia de la antena automática, de lo contrario, puede descargarse la batería o producirse un fallo de funcionamiento. ! El cable negro es el cable a tierra. Los cables a tierra de esta unidad y de otros productos (especialmente productos de alta tensión, como amplificadores de potencia) se deben conectar por separado, de lo contrario, puede producirse un incendio o un fallo de funcionamiento si se desconectan por accidente. Esta unidad 1 23 4 5 1 2 3 4 Entrada de la antena Fusible (10 A) Entrada del cable de alimentación Entrada remota conectada Es posible conectar un adaptador de mando a distancia físicamente conectado (se vende por separado). 5 Salida trasera o salida de subgraves Cable de alimentación 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d 1 A la toma del cable de alimentación 2 Según el tipo de vehículo, las funciones de 3 y 5 pueden ser diferentes. En este caso, conecte 4 a 5 y 6 a 3. 3 Amarillo Reserva (o accesorio) 4 Amarillo Conectar al terminal de alimentación constante de 12 V. 5 Rojo Accesorio (o reserva) 6 Rojo Conectar al terminal controlado por la llave de encendido (12 V CC). 7 Conecte entre sí los cables del mismo color. 8 Negro (Toma de tierra del chasis) 9 Azul/blanco La posición de las patillas del conector ISO será diferente según el tipo de vehículo. Conecte 9 y b cuando la patilla 5 sea del tipo control de antena. En otro tipo de vehículo, no se deben conectar nunca 9 y b. a Azul/blanco Conectar al terminal de control del sistema del amplificador de potencia (máx. 300 mA 12 V CC). b Azul/blanco Conectar al terminal de control del relé de la antena automática (máx. 300 mA 12 V CC). c Amarillo/negro Si utiliza un equipo con función de silenciamiento, conecte este cable con el cable de silenciamiento de audio de ese equipo. En caso contrario, mantenga el cable de silenciamiento de audio sin ninguna conexión. d Cables de altavoces Blanco: delantero izquierdo + Blanco/negro: delantero izquierdo * Gris: delantero derecho + Gris/negro: delantero derecho * Verde: trasero izquierdo + o altavoz de subgraves + Es <QRD3247-B> 63 Español — Vehículos con una batería de 12 voltios y conexión a tierra negativa. — Altavoces con 50 W (valor de salida) y 4 W a 8 W (valor de impedancia). — Nunca corte el aislamiento del cable de alimentación de esta unidad para compartir la corriente con otros equipos. La capacidad de corriente del cable es limitada. — Utilice un fusible con la intensidad nominal indicada. — Nunca conecte el cable negativo de los altavoces directamente a tierra. — Nunca empalme los cables negativos de varios altavoces. 03 63 Black plate (64,1) Sección Instalación 03 Instalación Verde/negro: trasero izquierdo * o altavoz de subgraves * Violeta: trasero derecho + o altavoz de subgraves + Violeta/negro: trasero derecho * o altavoz de subgraves * e Conector ISO En algunos vehículos, el conector ISO puede estar dividido en dos. En este caso, asegúrese de conectar los dos conectores. Notas ! Cambie el menú inicial de esta unidad. Consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página 62. La salida de graves de esta unidad es monoaural. ! Al usar un altavoz de subgraves de 70 W (2 W), conecte el mismo a los cables violeta y violeta/negro de esta unidad. No conecte nada al cable verde ni al verde/negro. Instalación ! ! ! ! Cómo realizar la instalación Importante Compruebe todas las conexiones y sistemas antes de la instalación final. No utilice piezas no autorizadas, ya que pueden causar fallos de funcionamiento. Consulte a su distribuidor si para la instalación es necesario taladrar orificios o hacer otras modificaciones al vehículo. No instale esta unidad en un lugar donde: — Pueda interferir con el manejo del vehículo. — Pueda lesionar a un pasajero como consecuencia de un frenazo brusco. Realice estas conexiones cuando utilice el amplificador opcional. 3 1 5 2     4 5 1 Control remoto del sistema Conexión a cable azul/blanco. 2 Amplificador de potencia (se vende por separado) 3 Conectar con cables RCA (se venden por separado) 4 A la salida trasera o salida de subgraves 5 Altavoz trasero o altavoz de subgraves Antes de instalar esta unidad 1 Retire el anillo de guarnición. 1 Soporte (pieza suministrada de fábrica) ! El láser semiconductor se dañará si se sobrecalienta. Instale esta unidad alejada de zonas que alcancen altas temperaturas, como cerca de la salida del calefactor. ! Se logra un rendimiento óptimo si la unidad se instala en un ángulo inferior a 60°. Instalación con el soporte 1 Instale el soporte en el panel. Después de insertar el soporte en el panel, seleccione las pestañas que se acoplen al espesor del material del panel, y dóblelas (instale esta unidad tan firmemente como sea posible, usando las pestañas superior e inferior; para fijar la unidad, doble las pestañas 90 grados). 60° Amplificador de potencia (se vende por separado) 1 ! Cuando instale, para asegurar la dispersión apropiada del calor durante el uso de esta unidad, asegúrese de dejar un amplio espacio por detrás del panel trasero y enrolle los cables sueltos de modo que no bloqueen las aberturas de ventilación. 1 Esta unidad se puede instalar utilizando uno de los siguientes dos métodos: ! Instalación con el soporte ! Instalación usando los agujeros para tornillos ubicados en ambos costados de la unidad 1 1 Anillo de guarnición 2 Inserte en ambos lados de la unidad las llaves de extracción provistas hasta que se escuche un ligero chasquido. 2 Deje un amplio espacio 1 Salpicadero 2 Soporte (pieza suministrada de fábrica) 5 cm 5 cm 3 Extraiga la unidad del soporte. Retire el soporte. ! En la instalación, emplee piezas disponibles en el mercado. 64 Es <QRD3247-B> 64 Black plate (65,1) Sección Instalación 2 Instale esta unidad. Información adicional Instalación usando los agujeros para tornillos ubicados en ambos costados de la unidad % Fijar la unidad al soporte de montaje de radio de fábrica. Coloque la unidad de forma que los orificios para los tornillos estén alineados con los orificios para los tornillos de la carcasa y, a continuación, apriete los tornillos en tres lugares en cada lado. 1 Solución de problemas Mensajes de error Los síntomas se escriben en negrita y las causas en escritura normal sin sangría. El texto normal con sangría se utiliza para indicar las acciones que se han de tomar. Anote el mensaje de error antes de contactar con su concesionario o con el servicio técnico oficial de Pioneer más cercano. Los mensajes de error se escriben en negrita y producen un texto normal sin sangrado. El texto normal y sangrado se emplea para indicar las acciones que se han de tomar. La pantalla vuelve automáticamente a la visualización normal. No ha realizado ninguna operación en aproximadamente 30 segundos. Realice la operación de nuevo. 1 Salpicadero 3 El intervalo de repetición de reproducción cambia de manera inesperada. Coloque el anillo de guarnición. 1 Cómo retirar el soporte El procedimiento es igual al de Antes de instalar esta unidad. Para más información, consulte Antes de instalar esta unidad en la página 64. Reproductor de CD NO XXXX aparece cuando se cambia una pantalla (NO TITLE, por ejemplo). 1 Anillo de guarnición No hay información de texto incorporada. Cambie la pantalla o reproduzca otra pista/ archivo. 3 4 1 Si la lengüeta supone un impedimento, dóblela hacia abajo. 2 Soporte de montaje de radio de fábrica 3 Tornillos de cabeza redonda (5 mm × 8 mm) 4 Salpicadero o consola La unidad no funciona o la conexión de los altavoces es incorrecta; se activa el circuito de protección. Compruebe la conexión de los altavoces. Si el mensaje no desaparece aun después de apagar y volver a encender el motor, contacte con su distribuidor o con el Servicio técnico oficial Pioneer. No se reproduce una subcarpeta. No se pueden reproducir las subcarpetas cuando se selecciona FLD (repetición de carpeta). Seleccione otro intervalo de repetición de reproducción. 1 Comunes AMP ERROR Español Dependiendo del intervalo de repetición de reproducción, el intervalo seleccionado puede cambiar cuando se selecciona otra carpeta o pista o cuando se utilice el avance rápido/retroceso. Seleccione de nuevo el intervalo de repetición de reproducción. 2 03 La unidad no funciona correctamente. Hay una interferencia. Está utilizando un dispositivo, como un teléfono móvil, que puede causar interferencias. Aleje de la unidad los dispositivos eléctricos que puedan estar causando interferencias. ERROR-07, 11, 12, 17, 30 El disco está sucio. Limpie el disco. El disco está rayado. Sustituya el disco. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Se ha producido un error eléctrico o mecánico. Coloque la llave de encendido del automóvil en la posición de desactivación y luego pase de nuevo a activación, o cambie a una fuente diferente y, a continuación, vuelva a activar el reproductor de CD. ERROR-15 El disco insertado aparece en blanco. Sustituya el disco. Es <QRD3247-B> 65 65 Black plate (66,1) Apéndice Información adicional ERROR-23 Formato de CD no compatible. Sustituya el disco. FORMAT READ A veces se produce un retraso entre el comienzo de la reproducción y la emisión del sonido. Espere hasta que el mensaje desaparezca y oiga sonido. Información adicional El dispositivo de almacenamiento USB conectado tiene la seguridad activada. Para desactivar la seguridad, siga las instrucciones del dispositivo de almacenamiento USB. SKIPPED El dispositivo de almacenamiento USB conectado tiene archivos protegidos con DRM. Los archivos protegidos se saltan. PROTECT Todos los archivos en el dispositivo de almacenamiento USB conectado tienen DRM integrado. Cambie el dispositivo de almacenamiento USB. SKIPPED El disco insertado contiene archivos protegidos con DRM. Los archivos protegidos se saltan. PROTECT Todos los archivos del disco insertado tienen DRM integrado. Sustituya el disco. Dispositivo de almacenamiento USB o iPod N/A USB El dispositivo USB conectado no es compatible con esta unidad. ! Conecte un dispositivo que cumpla con la clase de almacenamiento masivo USB. ! Desconecte su dispositivo y sustitúyalo por un dispositivo de almacenamiento USB compatible. NO AUDIO No hay canciones. Transfiera los archivos de audio al dispositivo de almacenamiento USB y conéctelo. No hay canciones relacionadas. Transfiera canciones al iPod. Error de comunicación. Realice una de las siguientes operaciones: –Cambie la llave de encendido del automóvil a la posición de desactivación y luego pase de nuevo a activación. –Desconecte el dispositivo de almacenamiento USB. –Cambie a una fuente diferente. Después vuelva a la fuente USB. Aplicación START UP APP La aplicación no se ha iniciado aún. Siga las instrucciones que aparecen en la pantalla. Pautas para el manejo Discos y reproductor Utilice únicamente discos que tengan uno de estos dos logotipos: Fallo del iPod. Desconecte el cable del iPod. Una vez que aparezca el menú principal del iPod, vuelva a conectar el iPod y reinícielo. CHECK USB El conector USB o el cable USB está cortocircuitado. Compruebe que el conector USB o el cable USB no esté enganchado en algo ni dañado. FORMAT READ A veces se produce un retraso entre el comienzo de la reproducción y la emisión del sonido. Espere hasta que el mensaje desaparezca y oiga sonido. NOT FOUND El iPod funciona correctamente pero no se carga. Compruebe que el cable de conexión del iPod no esté cortocircuitado (p. ej., atrapado entre objetos metálicos). Una vez confirmado, cambie la llave de encendido del automóvil a la posición de desactivación y luego pase de nuevo a activación; o bien desconecte una vez el iPod y conéctelo de nuevo. ERROR-19 NO AUDIO El disco insertado no contiene archivos reproducibles. Sustituya el disco. CHECK USB ERROR-23 El dispositivo de almacenamiento USB no está formateado con FAT12, FAT16 ni FAT32. El dispositivo de almacenamiento USB debe formatearse con FAT12, FAT16 o FAT32. Utilice discos de 12 cm. Utilice sólo discos convencionales y completamente circulares. CHECK USB El dispositivo de almacenamiento USB consume más de la corriente máxima admisible. Desconecte el dispositivo de almacenamiento USB y no lo utilice. Coloque la llave de encendido del automóvil en posición OFF, luego en ACC u ON y, a continuación, conecte únicamente dispositivos de almacenamiento USB compatibles. ERROR-16 La versión de firmware del iPod es antigua. Actualice la versión del iPod. Fallo del iPod. Desconecte el cable del iPod. Una vez que aparezca el menú principal del iPod, vuelva a conectar el iPod y reinícielo. STOP No hay canciones en la lista actual. Seleccione una lista que contenga canciones. 66 Es <QRD3247-B> 66 Black plate (67,1) Apéndice Información adicional Los siguientes tipos de discos no se pueden utilizar con esta unidad: ! DualDisc ! Discos de 8 cm: Si se utiliza este tipo de discos con un adaptador, puede provocar el funcionamiento defectuoso de la unidad. ! Discos con formas extrañas ! Discos que no sean CD ! Discos dañados, incluido discos que estén partidos, desconchados o deformados ! Discos CD-R/RW que no se han finalizado Información adicional Al usar discos de superficie imprimible para etiquetas, lea primero las instrucciones y las advertencias de los discos. Es posible que algunos discos no puedan insertarse ni expulsarse. La utilización de este tipo de discos puede dañar el equipo. No pegue etiquetas compradas por separado ni otro tipo de material a los discos. ! Los discos podrían combarse y no podrán reproducirse. ! Las etiquetas pueden despegarse durante la reproducción, evitando la expulsión del disco y causando de este modo daños en el equipo. No toque la superficie grabada de los discos. Cuando no utilice los discos, guárdelos en sus cajas. Dispositivo de almacenamiento USB No se admiten las conexiones a través de un concentrador USB. Para limpiar un CD, pásele un paño suave desde el centro hacia afuera. No conecte ningún otro objeto que no sea un dispositivo de almacenamiento USB. La condensación puede afectar temporalmente al rendimiento del reproductor. Deje de usarlo durante una hora aproximadamente para que se adapte a la temperatura más cálida. Además, si los discos tienen humedad, séquelos con un paño suave. Cuando conduzca, fije el dispositivo de almacenamiento USB firmemente. No deje caer el dispositivo de almacenamiento USB al suelo, ya que puede quedar atascado debajo del freno o del acelerador. Quizá no pueda reproducir algunos discos debido a sus características, formato, programas grabados, entorno de reproducción, condiciones de almacenamiento u otras causas. Las vibraciones en las carreteras pueden interrumpir la reproducción de un disco. Se pueden producir los siguientes problemas según el dispositivo de almacenamiento USB que se utilice. ! Las operaciones pueden variar. ! Es posible que no se reconozca el dispositivo de almacenamiento. ! Puede que los archivos no se reproduzcan correctamente. ! El dispositivo puede causar interferencias al escuchar la radio. No deje el iPod en lugares expuestos a una temperatura elevada. Cuando conduzca, fije el iPod firmemente. No deje caer el iPod al suelo, ya que puede quedar atascado debajo del freno o del acelerador. Acerca de los ajustes del iPod ! Cuando el iPod está conectado, esta unidad desactiva el ajuste EQ (ecualizador) del iPod para mejorar la acústica; al desconectar el iPod, el EQ retoma su valor original. ! No puede desactivar la Repetición del iPod cuando utiliza esta unidad. La Repetición se cambiará automáticamente a Todo cuando el iPod esté conectado a esta unidad. La unidad no mostrará el texto incompatible guardado en el iPod. Frecuencia de muestreo: de 8 kHz a 48 kHz (32 kHz, 44,1 kHz, 48 kHz para énfasis) Versiones de etiqueta ID3 compatibles: 1.0, 1.1, 2.2, 2.3, 2.4 (la etiqueta ID3 versión 2.x tiene prioridad sobre la versión 1.x) Lista de reproducción M3u: no compatible MP3i (MP3 interactivo), mp3 PRO: no compatible WAV Extensión de archivo: .wav Bits de cuantificación: 8 y 16 (LPCM), 4 (MS ADPCM) Frecuencia de muestreo: 16 kHz a 48 kHz (LPCM), 22,05 kHz y 44,1 kHz (MS ADPCM) Español No fije etiquetas, no escriba ni aplique sustancias químicas en la superficie de los discos. iPod ! No puede usar esta función con USB MTP. Compatibilidad con audio comprimido (disco, USB) WMA Extensión de archivo: .wma Velocidad de grabación: de 48 kbps a 320 kbps (CBR) y de 48 kbps a 384 kbps (VBR) Frecuencia de muestreo: 32 kHz, 44,1 kHz, 48 kHz Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream con vídeo: no compatible Información complementaria Solo se pueden visualizar los primeros 32 caracteres como nombre de archivo (incluida la extensión) o nombre de carpeta. Los textos en ruso que se visualizarán en esta unidad se deben codificar con los siguientes conjuntos de caracteres: ! Unicode (UTF-8, UTF-16) ! Los conjuntos de caracteres distintos de Unicode que se usan en el entorno Windows y que están ajustados en ruso en la configuración de idiomas múltiples. MP3 Extensión de archivo: .mp3 Velocidad de grabación: de 8 kbps a 320 kbps (CBR), VBR Es <QRD3247-B> 67 67 Black plate (68,1) Apéndice Información adicional Esta unidad puede no funcionar correctamente, según la aplicación utilizada para codificar archivos WMA. Puede producirse una pequeña demora cuando se inicie la reproducción de archivos de audio que contienen datos de imágenes o archivos de audio almacenados en un dispositivo USB con numerosas jerarquías de carpetas. Información adicional Reproducción de archivos protegidos por derechos de autor: no compatible Dispositivo de almacenamiento USB particionado: solo se puede reproducir la primera partición. Puede producirse cierto retraso cuando se inicie la reproducción de archivos de audio en un dispositivo de almacenamiento USB con numerosas jerarquías de carpetas. Disco PRECAUCIÓN Jerarquía de carpetas reproducibles: hasta ocho niveles (una jerarquía práctica de carpetas tiene menos de dos niveles). Carpetas reproducibles: hasta 99 Archivos reproducibles: hasta 999 Sistema de archivos: ISO 9660 Nivel 1 y 2, Romeo, Joliet ! Pioneer no garantiza la compatibilidad con todos los dispositivos de almacenamiento masivo USB y no se hace responsable de la pérdida de los datos en los reproductores multimedia, smartphones u otros dispositivos, mientras se utilicen con este producto. ! No deje discos ni dispositivos de almacenamiento USB en lugares expuestos a altas temperaturas. ! ! ! ! iPhone 4 iPhone 3GS iPhone 3G iPhone Independientemente de la longitud de la secciones en blanco que haya entre las canciones de la grabación original, los discos de audio comprimidos se reproducirán con una breve pausa entre cada canción. Dispositivo de almacenamiento USB Jerarquía de carpetas reproducibles: hasta ocho niveles (una jerarquía práctica de carpetas tiene menos de dos niveles). Carpetas reproducibles: hasta 500 Archivos reproducibles: hasta 15 000 68 Compatibilidad con iPod Esta unidad sólo es compatible con los modelos de iPod que se muestran a continuación. Fabricado para ! iPod touch (5.ª generación) ! iPod touch (4.ª generación) ! iPod touch (3.ª generación) ! iPod touch (2.ª generación) ! iPod touch (1.ª generación) ! iPod classic ! iPod con vídeo ! iPod nano (7.ª generación) ! iPod nano (6.ª generación) ! iPod nano (5.ª generación) ! iPod nano (4.ª generación) ! iPod nano (3.ª generación) ! iPod nano (2.ª generación) ! iPod nano (1.ª generación) ! iPhone 5 ! iPhone 4S 01 02 1 2 03 Según la generación o versión del iPod, es posible que algunas funciones no estén disponibles. Los usuarios de iPod con conector Lightning deberían usar el cable Lightning a USB (suministrado con el iPod). 3 4 04 5 6 Las funciones pueden variar según la versión de software del iPod. 05 Nivel 1 Nivel 2 Nivel 3 Nivel 4 : carpeta : archivo de audio comprimido 01 a 05: número de carpeta 1 a 6: secuencia de reproducción Disco Los usuarios de iPod con el conector del Dock deberían utilizar CD-IU51. Para más información, consulte a su proveedor. La secuencia de selección de carpetas u otras operaciones pueden diferir, dependiendo del software de codificación o escritura. Si desea más información sobre la compatibilidad de archivos y formatos, consulte los manuales del iPod. Dispositivo de almacenamiento USB Audiolibro, podcast: compatible Reproducción multisesión: compatible Transferencia de datos en formato Packet Write: no compatible Ejemplo de una jerarquía PRECAUCIÓN Pioneer no asume ninguna responsabilidad por la pérdida de datos en el iPod, incluso si la pérdida ocurre durante el uso de esta unidad. Secuencia de archivos de audio El usuario no puede asignar números de carpeta ni especificar secuencias de reproducción con esta unidad. La secuencia de reproducción es la misma que la secuencia grabada en el dispositivo de almacenamiento USB. Para especificar la secuencia de reproducción, se recomienda el siguiente método. 1 Cree un nombre del archivo que incluya números que especifiquen la secuencia de reproducción (p. ej., 001xxx.mp3 y 099yyy.mp3). 2 Coloque esos archivos en una carpeta. 3 Guarde la carpeta que contiene los archivos en el dispositivo de almacenamiento USB. Sin embargo, dependiendo del entorno del sistema, tal vez no pueda especificar la secuencia de reproducción. Para reproductores de audio portátiles USB, la secuencia es diferente y depende del reproductor. Es <QRD3247-B> 68 Black plate (69,1) Apéndice Información adicional Información adicional Tabla de caracteres rusos D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я D: Visualización C: Carácter Copyright y marcas registradas La venta de este producto solo otorga una licencia para su uso privado, no comercial. No otorga ninguna licencia ni concede ningún derecho a utilizar este producto en transmisiones comerciales (es decir, lucrativas) en tiempo real (terrestres, vía satélite, por cable y/o por cualquier otro medio), transmisiones/streaming por Internet, intranets u otras redes o en otros sistemas de distribución de contenido electrónico, como por ejemplo, aplicaciones de pago por escucha (pay-audio) o audio bajo demanda (audio-on-demand). Se necesita una licencia independiente para su uso comercial. Para obtener más información, visite http://www.mp3licensing.com. iPod y iPhone iPhone, iPod, iPod classic, iPod nano y iPod touch son marcas comerciales de Apple Inc., registradas en los EE. UU. y en otros países. Lightning es una marca comercial de Apple Inc. “Made for iPod” y “Made for iPhone” significan que un accesorio electrónico ha sido diseñado para ser conectado específicamente a un iPod o a un iPhone, respectivamente, y ha sido homologado por quien lo desarrolló para cumplir con las normas de funcionamiento de Apple. Apple no es responsable del funcionamiento de este aparato ni de que cumpla con las normas de seguridad y reguladoras. Tenga presente que el empleo de este accesorio con un iPod o iPhone puede afectar la operación inalámbrica. Androidä Android es una marca comercial de Google Inc. Especificaciones Generales Fuente de alimentación .... 14,4 V cc (10,8 V a 15,1 V permisible) Sistema de derivación a tierra ................................... Tipo negativo Consumo máximo de corriente ................................... 10,0 A Dimensiones (An × Al × Pr): DIN Bastidor ........................... 178 mm × 100 mm × 157 mm Cara anterior .................... 188 mm × 118 mm × 25 mm D Bastidor ........................... 178 mm × 100 mm × 165 mm Cara anterior .................... 170 mm × 96 mm × 17 mm Peso ................................ 1,2 kg Audio Potencia de salida máxima ................................... 50 W × 4 70 W × 1/2 W (para altavoz de subgraves) Potencia de salida continua ................................... 22 W × 4 (50 Hz a 15 000 Hz, 5 % THD, 4 W de carga, ambos canales activados) Impedancia de carga ....... 4 W (4 W a 8 W permisibles) Nivel de salida máxima del preamplificador ................................... 2,0 V Contorno de sonoridad ..... +10 dB (100 Hz), +6,5 dB (10 kHz) (volumen: –30 dB) Ecualizador (ecualizador gráfico de 5 bandas): Frecuencia ....................... 80 Hz/250 Hz/800 Hz/2,5 kHz/ 8 kHz Gama de ecualización ...... ±12 dB (paso de 2 dB ) Altavoz de subgraves (mono): Frecuencia ....................... 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pendiente ........................ –12 dB/oct, –24 dB/oct Ganancia ......................... +6 dB a –24 dB Fase ................................. Normal/Inversa WMA Windows Media es una marca registrada o una marca de fábrica de Microsoft Corporation en los Estados Unidos y/u otros países. Reproductor de CD Sistema ........................... Sistema de audio de discos compactos Discos utilizables ............. Disco compacto Relación de señal a ruido ................................... 94 dB (1 kHz) (red IEC-A) Número de canales .......... 2 (estéreo) Formato de decodificación MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato de decodificación WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (audio 2 canales) (Windows Media Player) Formato de señal WAV ..... PCM lineal & MS ADPCM (No comprimido) USB Especificación de la norma USB ................................... USB 2.0 velocidad máxima Consumo máximo de corriente ................................... 1 A Clase USB ....................... MCS (Clase de almacenamiento masivo) Sistema de archivos ......... FAT12, FAT16, FAT32 Formato de decodificación MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato de decodificación WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (audio 2 canales) (Windows Media Player) Formato de señal WAV ..... PCM lineal & MS ADPCM (No comprimido) Español MP3 Este producto incluye tecnología propiedad de Microsoft Corporation, y no se puede usar ni distribuir sin una licencia de Microsoft Licensing, Inc. Sintonizador de FM Intervalo de frecuencias ... de 87,5 MHz a 108,0 MHz Sensibilidad utilizable ...... 9 dBf (0,8 µV/75 W, mono, señal/ruido: 30 dB) Relación de señal a ruido ................................... 72 dB (red IEC-A) Sintonizador de MW Intervalo de frecuencias ... de 531 kHz a 1 602 kHz Sensibilidad utilizable ...... 25 µV (señal/ruido: 20 dB) Relación de señal a ruido ................................... 62 dB (red IEC-A) Sintonizador de LW Intervalo de frecuencias ... de 153 kHz a 281 kHz Sensibilidad utilizable ...... 28 µV (señal/ruido: 20 dB) Relación de señal a ruido ................................... 62 dB (red IEC-A) Nota Las especificaciones y el diseño están sujetos a modificaciones sin previo aviso. Es <QRD3247-B> 69 69 Black plate (70,1) Abschnitt Bevor Sie beginnen 01 Vielen Dank, dass Sie sich für dieses PIONEER-Produkt entschieden haben Bitte lesen Sie diese Anleitung vor der Verwendung dieses Produkts zur Gewährleistung seiner ordnungsgemäßen Verwendung durch. Lesen und befolgen Sie dabei insbesondere die Hinweise WARNUNG und VORSICHT. Bewahren Sie die Anleitung zur zukünftigen Bezugnahme sicher und griffbereit auf. Bevor Sie beginnen Zu diesem Gerät Die Tuner-Frequenzen dieses Geräts sind für Westeuropa, Asien, den Mittleren Osten, Afrika und Ozeanien bestimmt. Der Gebrauch in anderen Gebieten kann zu mangelhaftem Empfang führen. Die RDS-Funktion (Radio-Datensystem) funktioniert nur in Gebieten mit UKW-Sendern, die RDS-Signale ausstrahlen. Wichtig Bitte tragen Sie die folgenden Informationen in das dafür vorgesehene Formular auf der Rückseite der Anleitung ein: Mischen Sie dieses Produkt, wenn Sie es entsorgen wollen, nicht mit gewöhnlichen Haushaltsabfällen. Es gibt ein getrenntes Sammelsystem für gebrauchte elektronische Produkte, über das die richtige Behandlung, Rückgewinnung und Wiederverwertung gemäß der bestehenden Gesetzgebung gewährleistet wird. Privathaushalte in den Mitgliedstaaten der EU, in der Schweiz und in Norwegen können ihre gebrauchten elektronischen Produkte kostenfrei bei speziell dafür eingerichteten Sammelstellen abgeben oder zu einem Fachhändler zurückbringen (sofern sie ein vergleichbares neues Produkt kaufen). In den Ländern, die hier nicht aufgeführt sind, wenden Sie sich hinsichtlich der zu beachtenden Entsorgungsweise bitte an die zuständige Gemeindeverwaltung. Auf diese Weise stellen Sie sicher, dass das zu entsorgende Produkt der erforderlichen Verarbeitung, Rückgewinnung und Wiederverwertung zugeführt wird, und verhindern damit potenziell negative Auswirkungen auf die Umwelt sowie Gesundheitsschäden. 70 — 14-stellige Seriennummer (an der Unterseite des Geräts angegeben) — Kaufdatum (Datum der Quittung) — Stempel des Händlers Diese Informationen dienen als Eigentumsnachweis. Im Fall eines Diebstahls teilen Sie der Polizei die 14-stellige Seriennummer und das Kaufdatum des Geräts mit. Bewahren Sie die Bedienungsanleitung an einem sicheren Ort auf. VORSICHT ! Dieses Gerät darf nicht mit Flüssigkeiten in Kontakt kommen. Dies könnte einen Stromschlag verursachen. Darüber hinaus kann der Kontakt mit Flüssigkeit eine Beschädigung des Geräts, Rauchentwicklung und Überhitzung nach sich ziehen. ! Wählen Sie stets eine Lautstärke, bei der Sie Umgebungsgeräusche noch deutlich wahrnehmen können. ! Setzen Sie dieses Gerät keiner Feuchtigkeit aus. VORSICHT Bei diesem Gerät handelt es sich zwar um ein Laserprodukt der Klasse 1, das entsprechend dem Standard Sicherheit für Laserprodukte IEC 60825-1:2007 klassifiziert ist. LASER KLASSE 1 Im Problemfall WARNUNG ! Versuchen Sie nicht, dieses Produkt selbst zu montieren oder zu warten. Werden Montage- oder Wartungsarbeiten des Produkts von Personen ohne Ausbildung und Erfahrung hinsichtlich elektronischer Geräte und Fahrzeugzubehör vorgenommen, kann dies gefährlich sein und möglicherweise zu elektrischen Schlägen, Verletzungen oder anderen Gefahren führen. ! Bedienen Sie das Gerät niemals während der Fahrt. Fahren Sie an den Straßenrand und parken Sie Ihr Fahrzeug zuerst an einem sicheren Ort, bevor Sie die Bedienelemente des Geräts bedienen. Sollte dieses Gerät nicht ordnungsgemäß funktionieren, dann wenden Sie sich an Ihren Händler oder an die nächstgelegene PIONEERKundendienststelle. De <QRD3247-B> 70 Black plate (71,1) Abschnitt Gebrauch dieses Geräts Hauptgerät 1 2 Gebrauch dieses Geräts 2 Drehen Sie M.C., um zu YES umzuschalten. Display-Anzeige 3 4 2 1 5 3 4 5 7 9 6 8 a 1 6 7 1 h (Auswurf) 2 iPod 89 1/ Disc-Ladeschacht 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d 9 MULTI-CONTROL (M.C.) a b 3 Unterinformationsbereich 4 TA (Verkehrsdurchsagen) LANGUAGE (Spracheinstellung) 5 TP (Verkehrsprogramm-Identifizierung) Das Gerät kann Textinformationen komprimierter Audiodateien auch dann anzeigen, wenn sie auf Englisch, Russisch oder Türkisch aufgezeichnet wurden. ! Falls die für die Aufzeichnung verwendete Sprache und die gewählte Spracheinstellung nicht übereinstimmen, werden die Textinformationen ggf. nicht richtig angezeigt. ! Bestimmte Zeichen werden ggf. nicht ordnungsgemäß angezeigt. 1 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ENG (Englisch)—РУС (Russisch)—TUR (Türkisch) 2 Drücken Sie M.C., um die Auswahl zu bestätigen. 6 7 9 (iPod-Steuerung) a (Zurück)/DIMMER (Dimmer) (Liste) AUX-Eingang (3,5-mm-Stereoanschluss) d USB-Anschluss b (Sound Retriever) LOC (Lokal-Suchlaufabstimmung) (Wiederholwiedergabe) (zufällige Wiedergabe) Hauptinformationsbereich ! Tuner: Frequenzband und Frequenz ! RDS: Programm-Service-Name, PTY-Information und andere Textinformationen ! CD-Player, USB-Speichermedium und iPod: verstrichene Wiedergabezeit und Textinformationen Erscheint, wenn eine untergeordnete Ordner- oder Menüebene vorhanden ist. VORSICHT Verwenden Sie für den Anschluss eines USBSpeichergeräts ein optionales USB-Kabel von Pioneer (CD-U50E), da direkt an diese Einheit angeschlossene Zusatzgeräte hervorstehen und eine Gefahr darstellen könnten. 4 Befolgen Sie diese Schritte, um das Menü einzurichten. Sie müssen Ihre Auswahl bestätigen, um die nächste Menüoption aufrufen zu können. (iPod-Steuerung) Die iPod-Funktionen dieses Geräts werden über Ihren iPod bedient. 8 c Drücken Sie zur Auswahl M.C. 2 a b cd bis 6/ 3 (Liste) Setup-Menü 1 Drehen Sie nach der Installation des Geräts den Zündschalter auf EIN. Die Angabe SET UP erscheint. FM STEP (UKW-Kanalraster) Verwenden Sie FM STEP, um die UKW-Kanalrasteroptionen (Suchschritteinstellungen) einzustellen. 1 Drehen Sie M.C., um die UKW-KanalrasterFunktion zu wählen. 100 (100 kHz)—50 (50 kHz) 2 Drücken Sie M.C., um die Auswahl zu bestätigen. Die Angabe QUIT erscheint. ! Bei der manuellen Abstimmung ist das Kanalraster auf 50 kHz fest eingestellt. ! Wenn AF und TA deaktiviert sind, ist für das Suchlauf-Kanalraster 50 kHz fest eingestellt, selbst wenn 100 ausgewählt ist. 5 Um die Einstellungen abzuschließen, drehen Sie M.C., um zu YES zu wechseln. # Möchten Sie Ihre Einstellungen wieder ändern, drehen Sie M.C., um NO auszuwählen. 6 Drücken Sie zur Auswahl M.C. Hinweise ! Sie können die Menüoptionen über das Systemmenü und Grundmenü einstellen. Für Details zu den Einstellungen siehe Systemmenü auf Seite 78 und Grundmenü auf Seite 78. ! Das Einstellmenü kann durch Drücken von SRC/OFF abgebrochen werden. Deutsch 3 4 b # Wenn Sie das Gerät nicht innerhalb von 30 Sekunden bedienen, wird das Setup-Menü nicht angezeigt. # Wenn Sie es vorziehen, die Einstellungen nicht jetzt vorzunehmen, drehen die den M.C.-Regler auf NO. 02 Grundlegende Bedienvorgänge CLOCK SET (Einstellen der Uhrzeit) 1 Drehen Sie M.C., um die Stunde einzustellen. 2 Drücken Sie auf M.C., um die Minuten auszuwählen. 3 Drehen Sie M.C., um die Minuten einzustellen. 4 Drücken Sie M.C., um die Auswahl zu bestätigen. Einschalten des Geräts 1 Drücken Sie die Taste SRC/OFF, um das Gerät einzuschalten. Ausschalten des Geräts 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. De <QRD3247-B> 71 71 Black plate (72,1) Abschnitt Gebrauch dieses Geräts 02 Wählen einer Programmquelle 1 Drücken Sie SRC/OFF, um zwischen den folgenden Optionen umzuschalten: RADIO—CD—USB/iPod—APP (Anwendung) —AUX ! USB MTP wird angezeigt, während die MTPVerbindung hergestellt ist. ! Wenn ein iPod angeschlossen und eine andere Quelle als iPod gewählt ist, können Sie durch Drücken von iPod zu iPod wechseln. Regeln der Lautstärke 1 Drehen Sie M.C., um die Lautstärke anzupassen. Hinweis Wenn das blau/weiße Kabel dieses Geräts an die Steuerklemme des Automatikantennenrelais des Kraftfahrzeugs angeschlossen wird, wird die Antenne ausgefahren, sobald das Gerät eingeschaltet wird. Zum Einfahren der Antenne schalten Sie die Programmquelle aus. Häufig verwendete Menüschritte Zurückschalten zur vorherigen Anzeige Zum Zurückschalten zur vorherigen Liste (bzw. zum übergeordneten Ordner) 1 Drücken Sie /DIMMER. Zurückschalten zur normalen Anzeige Beenden des Hauptmenüs 1 Drücken Sie BAND/ . Zurückschalten zur normalen Anzeige von der Liste 1 Drücken Sie BAND/ . Gebrauch dieses Geräts Radio Grundlegende Bedienvorgänge Speichern und Abrufen von Radiostationen für jedes Band Verwendung der Stationstasten Wahl eines Bands (Wellenbereich) 1 Drücken Sie BAND/ , bis der gewünschte Wellenbereich angezeigt wird (FM1, FM2, FM3 für UKW bzw. MW/LW). Wechseln der voreingestellten Sender 1 Drücken Sie c oder d. ! Wählen Sie PCH (voreingesteller Kanal) unter SEEK, um diese Funktion verwenden zu können. Manuelle (schrittweise) Abstimmung 1 Drücken Sie c oder d. ! Wählen Sie MAN (manuelle Abstimmung) unter SEEK, um diese Funktion verwenden zu können. Suchlauf 1 Drücken und halten Sie c oder d gedrückt und lassen Sie die Taste dann wieder los. Durch kurzes Drücken von c oder d kann die Suchlaufabstimmung aufgehoben werden. Durch Drücken und Gedrückthalten von c oder d können Sender übersprungen werden. Die Suchlaufabstimmung beginnt, sobald c bzw. d losgelassen wird. Hinweise ! Details zu SEEK finden Sie unter SEEK (Einstellen der linken/rechten Tasten) auf Seite 73. ! Der Alternativfrequenz-Suchlauf (AF) dieses Geräts kann ein- und ausgeschaltet werden. Für den normalen Abstimmbetrieb sollte AF ausgeschaltet sein (siehe AF (Alternativfrequenz-Suchlauf) auf Seite 73). 1 Zum Speichern: Drücken Sie eine der Stationstasten (1/ bis 6/ ) und halten diese gedrückt, bis die Stationsnummer nicht mehr blinkt. 2 Zum Abrufen: Drücken Sie eine der Stationstasten (1/ bis 6/ ). Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! FREQUENCY (Programm-Service-Name oder Frequenz) ! BRDCST INFO (Programm-Service-Name/ PTY-Information) ! CLOCK (Programmquellname und Uhr) Hinweise ! Wenn der Programm-Service-Name nicht unter FREQUENCY abgerufen werden kann, wird stattdessen die Sendefrequenz angezeigt. Der Programm-Service-Name wird bei einer Erkennung angezeigt. ! Je nach dem Band kann die Textinformation geändert werden. ! Welche Textinformationen geändert werden können, hängt vom Bereich ab. Gebrauch der ProgrammtypFunktionen (PTY) Sie können einen Sender anhand eines Programmtyps (PTY) abstimmen. Suchen nach RDS-Stationen anhand eines Programmtyps (Liste). 1 Drücken Sie auf 2 Drehen Sie M.C., um einen Programmtyp zu wählen. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Drücken Sie M.C., um die Suche zu starten. Das Gerät sucht nach einer Station, die ein Programm des gewählten Typs ausstrahlt. Wenn eine solche Station gefunden wird, wird deren Stationsname angezeigt. ! Zum Aufheben des Suchlaufs drücken Sie M.C. erneut. ! Das Programm mancher Sender kann von dem tatsächlich übertragenen Programmtyp (PTY) abweichen. ! Wird kein Sender gefunden, der ein Programm des gewählten Typs ausstrahlt, dann erscheint zwei Sekunden lang NOT FOUND und der Tuner schaltet auf die ursprüngliche Station zurück. PTY-Liste Detaillierte Informationen zur PTY-Liste finden Sie auf folgender Website: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die gewünschte Funktion zu wählen. Nach der Auswahl können die folgenden Funktionen angepasst werden. 72 De <QRD3247-B> 72 Black plate (73,1) Abschnitt Gebrauch dieses Geräts # Wenn das MW/LW-Band gewählt ist, stehen nur BSM, LOCAL und SEEK zur Verfügung. FM SETTING (Einstellungen für die UKW-Klangqualität) Die Klangqualität kann so eingestellt werden, dass sie den Sendesignalbedingungen des UKWFrequenzbereichsignals entspricht. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ! STANDARD – Dies ist die Standardeinstellung. ! HI-FI – Diese Einstellung sollte verwendet werden, um vorzugsweise eine hohe Stereo-Klangqualität zu verwenden. ! STABLE – Diese Einstellung sollte verwendet werden, um vorzugsweise einen MonoKlang mit geringem Rauschen zu verwenden. BSM (Best-Sender-Memory) REGIONAL (Regional) Bei Verwendung des Alternativfrequenz-Suchlaufs beschränkt die Regionalfunktion die Auswahl auf Sender, die regionale Programme ausstrahlen. 1 Drücken Sie M.C., um die Regionalfunktion ein- oder auszuschalten. LOCAL (Lokal-Suchlaufabstimmung) Mit der Lokal-Suchlaufabstimmung wird nur nach Stationen mit ausreichender Signalstärke für einen guten Empfang gesucht. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. UKW: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Bei Auswahl der höchsten Stufe werden nur die stärksten Sender empfangen, während bei Auswahl der niedrigeren Stufen schwächere Sender zugelassen werden. CD/CD-R/CD-RW-Discs und USB-Speichermedien MTP-Verbindung MTP-kompatible Android-Geräte (mit AndroidBetriebssystem 4.0 oder höher) können über eine MTP-Verbindung unter Verwendung einer USB-Quelle verbunden werden. Um ein Android-Gerät anzuschließen, verwenden Sie das dem Gerät beiliegende Kabel. 02 Rückkehr zum Stammordner 1 Drücken und halten Sie BAND/ gedrückt. Umschalten zwischen dem komprimierten Audioformat und CD-DA 1 Drücken Sie BAND/ . TA (Verkehrsdurchsagebereitschaft) Hinweis Diese Funktion ist nicht mit WAV kompatibel. 1 Drücken Sie M.C., um die Verkehrsdurchsagebereitschaft ein- oder auszuschalten. Grundlegende Bedienvorgänge Umschalten zwischen Wiedergabespeichergeräten Sie können zwischen Wiedergabespeichereinheiten eines USB-Speichermediums wechseln, welches über mehrere Massenspeicherklasse kompatible Einheiten verfügt. 1 Drücken Sie BAND/ . ! Sie können zwischen bis zu 32 verschiedenen Speichergeräten wechseln. Wiedergabe einer CD/CD-R/CD-RW-Disc 1 Legen Sie die Disc mit der Etikettenseite nach oben in den Ladeschacht. Hinweis Trennen Sie USB-Speichermedien bei Nichtverwendung von diesem Gerät ab. AF (Alternativfrequenz-Suchlauf) 1 Drücken Sie M.C., um den AlternativfrequenzSuchlauf ein- oder auszuschalten. NEWS (Nachrichtenunterbrechung) 1 Drücken Sie M.C., um die Nachrichtenfunktion ein- oder auszuschalten. SEEK (Einstellen der linken/rechten Tasten) Sie können den linken und rechten Tasten des Gerät eine Funktion zuweisen. Wählen Sie MAN (manuelle Abstimmung) zur manuellen Abstimmung oder PCH (vorprogrammierter Kanal) zum Umschalten zwischen den vorprogrammierten Kanälen. 1 Drücken Sie M.C., um MAN oder PCH zu wählen. Auswerfen einer CD/CD-R/CD-RW-Disc 1 Drücken Sie auf h. Wiedergabe von Musiktiteln eines USB-Speichermediums 1 Öffnen Sie die Abdeckung des USB-Anschlusses. 2 Schließen Sie das USB-Speichermedium über ein USB-Kabel an. Deutsch BSM (Best-Sender-Memory) speichert die sechs stärksten Sender automatisch in der Reihenfolge ihrer Signalstärke. 1 Drücken Sie M.C., um BSM einzuschalten. Zum Abbrechen des Speichervorgangs drücken Sie M.C. erneut. Gebrauch dieses Geräts Wiedergabe der Musiktitel auf einem USB-Speichermedium abbrechen 1 Das USB-Speichermedium kann jederzeit vom Gerät getrennt werden. Wählen eines Ordners 1 Drücken Sie 1/ oder 2/ . Wahl eines Titels 1 Drücken Sie c oder d. Schnellvorlauf bzw. -rücklauf 1 Drücken und halten Sie c oder d gedrückt. ! Bei der Wiedergabe von Dateien im komprimierten Audio-Format wird beim schnellen Vor- und Rücklauf kein Ton ausgegeben. De <QRD3247-B> 73 73 Black plate (74,1) Abschnitt Gebrauch dieses Geräts 02 Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: CD-DA ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) CD-TEXT ! TRACK INFO (Titelname/Titel-Künstler/ Disc-Titel) ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) MP3/WMA/WAV ! TRACK INFO (Titelname/Künstlername/Albumtitel) ! FILE INFO (Dateiname/Ordnername) ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) Auswählen und Wiedergeben von Dateien/Titeln der Namensliste 1 Drücken Sie , um in den Datei-/Titellistenmodus umzuschalten. 2 Verwenden Sie M.C., um den Namen der gewünschten Datei (bzw. des gewünschten Ordners) zu wählen. Auswählen einer Datei oder eines Ordners 1 Drehen Sie M.C. Wiedergabe 1 Drücken Sie nach Auswahl einer Datei oder eines Titels auf M.C. 74 Gebrauch dieses Geräts Anzeige einer Liste der Dateien (oder Ordner) im gewählten Ordner 1 Drücken Sie nach Auswahl eines Ordners auf M.C. Wiedergabe eines Musiktitels im gewählten Ordner 1 Drücken und halten Sie M.C. nach Auswahl des Ordners gedrückt. Bedienvorgänge mit speziellen Tasten Wählen eines Wiederholbereichs 1 Drücken Sie 6/ , um zwischen den folgenden Optionen umzuschalten: CD/CD-R/CD-RW-Discs ! ALL – Wiederholung aller Titel ! ONE – Wiederholung des momentanen Titels ! FLD – Wiederholung des momentanen Ordners USB-Speichermedium ! ALL – Wiederholung aller Dateien ! ONE – Wiederholung der momentanen Datei ! FLD – Wiederholung des momentanen Ordners Abspielen von Titeln in zufälliger Reihenfolge , um die zufallsgesteuerte 1 Drücken Sie 5/ Wiedergabe ein- oder auszuschalten. Die Titel innerhalb des gewählten Wiederholbereichs werden in einer zufälligen Reihenfolge gespielt. ! Um Titel während der zufälligen Wiedergabe zu ändern, drücken Sie auf d, um zum nächsten Titel zu wechseln. Durch Drücken von c wird die Wiedergabe des aktuellen Titels von seinem Anfang neu gestartet. Pausieren der Wiedergabe 1 Drücken Sie 4/PAUSE, um die Wiedergabe anzuhalten oder fortzusetzen. Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) 1 Drücken Sie 3/S.Rtrv, um zwischen den folgenden Optionen umzuschalten: 1—2—OFF (Aus) 1 wirkt bei einem niedrigen und 2 bei einem hohen Kompressionsfaktor. Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. Nach der Auswahl kann die unten stehende Funktion angepasst werden. S.RTRV (Sound Retriever) Verbessert komprimierte Audiodaten und stellt ein reiches Klangbild wieder her. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. Für detaillierte Informationen hierzu siehe Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) auf Seite 74. iPod Grundlegende Bedienvorgänge Wiedergabe von Musiktiteln eines iPods 1 Öffnen Sie die Abdeckung des USB-Anschlusses. 2 Schließen Sie einen iPod an den USB-Eingang an. Die Wiedergabe erfolgt automatisch. Wahl eines Musiktitels (Kapitels) 1 Drücken Sie c oder d. Auswählen eines Albums 1 Drücken Sie 1/ oder 2/ . Schnellvorlauf bzw. -rücklauf 1 Drücken und halten Sie c oder d gedrückt. Hinweise ! Der iPod kann nicht ein- bzw. ausgeschaltet werden, wenn der Steuermodus CTRL AUDIO gewählt wurde. ! Trennen Sie die Kopfhörer vom iPod, bevor Sie ihn mit diesem Gerät verbinden. ! Wenn die Zündung des Wagens ausgeschaltet wird, schaltet sich der iPod nach etwa zwei Minuten aus. Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! TRACK INFO (Titelname/Künstlername/Albumtitel) ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) De <QRD3247-B> 74 Black plate (75,1) Abschnitt Gebrauch dieses Geräts Suchen nach Musiktiteln 1 Drücken Sie , um zum Hauptmenü der Listensuche zu wechseln. 2 Verwenden Sie M.C., um eine Kategorie bzw. einen Musiktitel auszuwählen. Musiktitel- oder Kategorienname ändern 1 Drehen Sie M.C. Spiellisten—Künstler—Alben—Musiktitel— Podcasts—Musik-Genres—Komponisten— Hörbücher Wiedergabe 1 Drücken Sie nach Auswahl eines Musiktitels auf M.C. Wiedergabe einer Musiktitelliste der ausgewählten Kategorie 1 Drücken Sie nach Auswahl einer Kategorie auf M.C. Wiedergabe eines Musiktitels der gewählten Kategorie 1 Drücken und halten Sie M.C. nach Auswahl der Kategorie gedrückt. Hinweise ! Sie können Spiellisten mithilfe einer auf unserer Website erhältlichen Computer-Anwendung (MusicSphere) erstellen. ! Die mithilfe dieser Computer-Anwendung (MusicSphere) erstellten Spiellisten werden abgekürzt angezeigt. Bedienvorgänge mit speziellen Tasten Wählen eines Wiederholbereichs 1 Drücken Sie 6/ , um zwischen den folgenden Optionen umzuschalten: ! ONE – Wiederholung des momentanen Musiktitels ! ALL – Wiederholung aller Musiktitel in der gewählten Liste ! Wenn als Steuermodus CTRL iPod gewählt wurde, ist der Wiederholbereich der gleiche wie im angeschlossenen iPod. Auswählen des zufälligen Wiederholbereichs (Shuffle) , um zwischen den folgen1 Drücken Sie 5/ den Optionen umzuschalten: ! SNG – Zufallsgesteuerte Wiedergabe der Musiktitel der gewählten Liste ! ALB – Wiedergabe in der richtigen Reihenfolge der Musiktitel in einem nach dem Zufallsprinzip gewählten Album ! OFF – Kein Abspielen in zufälliger Reihenfolge Abspielen aller Musiktitel in zufälliger Reihenfolge (Shuffle All) gedrückt, um 1 Drücken und halten Sie 5/ die Funktion „Shuffle All“ (zufällige Wiedergabe aller Titel) einzuschalten. ! Zum Ausschalten der Funktion „Shuffle All“ wählen Sie OFF im Shuffle-Modus. Für detaillierte Informationen hierzu siehe Auswählen des zufälligen Wiederholbereichs (Shuffle) auf Seite 75. Pausieren der Wiedergabe 1 Drücken Sie 4/PAUSE, um die Wiedergabe anzuhalten oder fortzusetzen. Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) 1 Drücken Sie 3/S.Rtrv, um zwischen den folgenden Optionen umzuschalten: 1—2—OFF (Aus) 1 wirkt bei einem niedrigen und 2 bei einem hohen Kompressionsfaktor. Wiedergabe von Musiktiteln mit Bezug zum momentan spielenden Titel Es können Musiktitel der folgenden Listen abgespielt werden: • Albumliste des momentan spielenden Künstlers • Musiktitelliste des momentan spielenden Albums • Albumliste des momentan spielenden MusikGenres 1 Drücken und halten Sie gedrückt, um in den Modus der verknüpften Wiedergabe umzuschalten. 2 Drehen Sie M.C., um den Modus zu wechseln, und drücken Sie ihn, um den angezeigten Modus zu wählen. ! ARTIST – Wiedergabe eines Albums des momentan spielenden Künstlers ! ALBUM – Wiedergabe eines Musiktitels eines Albums des momentan spielenden Künstlers ! GENRE – Wiedergabe eines Albums aus dem Genre des momentan spielenden Künstlers Der ausgewählte Musiktitel bzw. das ausgewählte Album wird nach dem gerade spielenden Musiktitel wiedergegeben. 02 Hinweise ! Die Wiedergabe des ausgewählten Musiktitels/Albums wird ggf. abgebrochen, wenn Sie eine andere Funktion als die Verbindungssuche (wie z. B. Schnellvorlauf oder -rücklauf) wählen. ! Je nach dem für die Wiedergabe gewählten Musiktitel können das Ende des momentan spielenden Musiktitels und der Anfang des ausgewählten Musiktitels/Albums abgeschnitten werden. Verwenden der iPod-Funktionen dieses Geräts über den iPod Die iPod-Funktionen dieses Geräts können über den angeschlossenen iPod gesteuert werden. CTRL iPod ist nicht mit den folgenden iPod-Modellen kompatibel: ! iPod nano der 1. Generation ! iPod mit Videos % Drücken Sie auf BAND/ , um in den Funktionssteuermodus zu wechseln. ! CTRL iPod – Die iPod-Funktionen dieses Geräts können über den angeschlossenen iPod bedient werden. ! CTRL AUDIO – Die iPod-Funktionen dieses Geräts können über das Gerät gesteuert werden. Deutsch Alphabetische Listensuche 1 Sobald die Liste der gewählten Kategorie angezeigt wird, drücken Sie die Taste , um in den alphabetischen Suchmodus umzuschalten. ! Durch zweimaliges Drehen von M.C. kann in den alphabetischen Suchmodus gewechselt werden. 2 Drehen Sie M.C., um einen Buchstaben zu wählen. 3 Drücken Sie M.C., um eine alphabetisch sortierte Liste anzuzeigen. ! Zum Abbrechen des Suchvorgangs drücken Sie auf /DIMMER. Gebrauch dieses Geräts Der Steuermodus kann auch durch Drücken auf iPod geändert werden. Hinweise ! Wenn Sie den Steuermodus auf CTRL iPod umschalten, wird die Musiktitelwiedergabe unterbrochen. Verwenden Sie den iPod, um mit der Wiedergabe fortzufahren. ! Selbst wenn CTRL iPod als Steuermodus gewählt wurde, können die folgenden Vorgänge direkt über dieses Gerät vorgenommen werden: — Pause — Schnellvorlauf/-rücklauf De <QRD3247-B> 75 75 Black plate (76,1) Abschnitt Gebrauch dieses Geräts 02 — Wahl eines Musiktitels (Kapitels) ! Die Lautstärke kann nur über das Hauptgerät angepasst werden. Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die gewünschte Funktion zu wählen. Nach der Auswahl können die folgenden Funktionen angepasst werden. ! AUDIO BOOK steht nicht zur Verfügung, wenn im Steuermodus CTRL iPod gewählt wurde. Für detaillierte Informationen hierzu siehe Verwenden der iPod-Funktionen dieses Geräts über den iPod auf Seite 75. AUDIO BOOK (Hörbuch-Abspielgeschwindigkeit) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die von Ihnen bevorzugte Einstellung zu wählen. ! FASTER – Schnellere Wiedergabe als normale Wiedergabegeschwindigkeit ! NORMAL – Normale Wiedergabegeschwindigkeit ! SLOWER – Langsamere Wiedergabe als normale Wiedergabegeschwindigkeit Gebrauch dieses Geräts Arbeiten mit Anwendungen angeschlossener Geräte Dieses Gerät können Sie zur Streaming-Wiedergabe und zum Steuern von Titeln in iPhone-Anwendungen oder nur für die StreamingWiedergabe verwenden. Wichtig Die Verwendung von Apps von Dritten kann eventuell die Angabe personenbezogener Daten nach sich ziehen oder notwendig machen entweder durch das Eröffnen eines Benutzerkontos o. Ä. und für bestimmte Anwendungen die Angabe von Geolokationsdaten. ALLE APPS VON DRITTEN UNTERLIEGEN DER ALLEINIGEN VERANTWORTUNG DER ANBIETER EINSCHLIESSLICH UND OHNE EINSCHRÄNKUNG DEM SAMMELN UND SICHERN DER ANWENDERDATEN UND DATENSCHUTZMASSNAHMEN. DURCH ZUGRIFF AUF APPS VON DRITTEN ERKLÄREN SIE SICH MIT DEN NUTZUNGSBEDINGUNGEN UND DATENSCHUTZRICHTLINIEN DER JEWEILIGEN ANBIETER EINVERSTANDEN. WENN SIE DEN NUTZUNGSBEDINGUNGEN UND RICHTLINIEN EINES ANBIETERS ODER DER VERWENDUNG VON GEOLOKATIONSDATEN, WO ZUTREFFEND, NICHT ZUSTIMMEN, DANN SEHEN SIE VON DER VERWENDUNG VON APPS VON DRITTEN AB. S.RTRV (Sound Retriever) 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. Für detaillierte Informationen hierzu siehe Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) auf Seite 75. 76 Informationen zur Kompatibilität von angeschlossenen Geräten Im Folgenden finden Sie detaillierte Informationen über die erforderlichen Anschlüsse, um die Anwendung für das iPhone auf diesem Gerät verwenden zu können. Für iPhone-Anwender ! Diese Funktion ist mit dem iPhone und dem iPod touch kompatibel. ! Das Gerät läuft unter dem iOS-Betriebssystem 5.0 oder höher. Hinweise ! Besuchen Sie unsere Website, um eine Liste der unterstützten iPhone-Anwendungen für dieses Gerät zu erhalten. ! Pioneer übernimmt keine Haftung für jegliche von inkorrekten oder fehlerhaften appbasierten Inhalten verursachte Probleme. ! Inhalt und Funktionalität der unterstützten Anwendungen liegen in der Verantwortlichkeit der App-Anbieter. Einrichtverfahren für iPhoneAnwender 1 Schließen Sie ein iPhone an den USB-Eingang an. 2 Ändern Sie die Quelle zu APP. 3 Starten Sie die Anwendung auf dem iPhone, und beginnen Sie mit der Wiedergabe. Grundlegende Bedienvorgänge Wahl eines Titels 1 Drücken Sie c oder d. Schnellvorlauf bzw. -rücklauf 1 Drücken und halten Sie c oder d gedrückt. Pausieren der Wiedergabe 1 Drücken Sie BAND/ , um die Wiedergabe anzuhalten oder fortzusetzen. Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! TRACK INFO (Titelname/Künstlername/Albumtitel) ! APP NAME (Anwendungsname) ! ELAPSED TIME (Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die gewünschte Funktion zu wählen. Nach der Auswahl können die folgenden Funktionen angepasst werden. PAUSE (Pause) 1 Drücken Sie M.C., um die Wiedergabe anzuhalten oder fortzusetzen. S.RTRV (Sound Retriever) 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. 1—2—OFF (Aus) 1 wirkt bei einem niedrigen und 2 bei einem hohen Kompressionsfaktor. Audio-Einstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. De <QRD3247-B> 76 Black plate (77,1) Abschnitt Gebrauch dieses Geräts 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf AUDIO, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die gewünschte Audio-Funktion zu wählen. Nach der Auswahl können die folgenden Audiofunktionen angepasst werden. ! FADER steht nicht zur Verfügung, wenn in SP-P/O MODE die Option SUB.W/SUB.W gewählt wurde. Für detaillierte Informationen hierzu siehe SP-P/O MODE (Heckausgangund Preout-Einstellungen) auf Seite 78. ! SUB.W und SUB.W CTRL stehen nicht zur Verfügung, wenn in SP-P/O MODE die Option REAR/REAR gewählt wurde. Für Details siehe SP-P/O MODE (Heckausgang- und Preout-Einstellungen) auf Seite 78. ! SUB.W CTRL steht nicht zur Verfügung, wenn in OFF die Option SUB.W gewählt wurde. Für Details siehe SUB.W (Subwoofer Ein/Aus) auf Seite 77. ! SLA steht nicht zur Verfügung, wenn als Quelle FM gewählt wurde. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Front-/Heck-Lautsprecherbalance einzustellen. BALANCE (Balance-Einstellung) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um einen Equalizer zu wählen. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS Das Equalizer-Band und der Equalizer-Pegel können individuell angepasst werden, wenn CUSTOM1 oder CUSTOM2 gewählt ist. Schließen Sie bei Wahl von CUSTOM1 oder CUSTOM2 den unten genannten Vorgang ab. Kehren Sie bei Wahl einer anderen Option durch Drücken auf M.C. zur vorherigen Anzeige zurück. ! CUSTOM1 kann für jede Quelle separat eingestellt werden. USB, iPod und APP sind hingegen automatisch auf die gleiche Einstellung gesetzt. ! Bei CUSTOM2 handelt es sich um eine gemeinsam verwendete Einstellung für alle Quellen. 3 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 4 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Equalizerband—Equalizer-Pegel 5 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Equalizer-Band: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizer-Pegel: +6 bis –6 LOUDNESS (Loudness) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Links-/Rechts-Lautsprecherbalance einzustellen. EQ SETTING (Equalizer-Abruf) Die Loudness-Funktion kompensiert die verminderte Wahrnehmung von niedrigen und hohen Frequenzen bei geringer Lautstärke. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. OFF (Aus)—LOW (Niedrig)—MID (Mittel)—HI (Hoch) Dieses Gerät ist mit einem Subwoofer-Ausgang ausgestattet, der ein- und ausgeschaltet werden kann. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. NOR (Normalphase)—REV (Gegenphase)— OFF (Subwoofer Aus) SUB.W CTRL (Subwoofer-Einstellungen) Vom Subwoofer werden nur solche Frequenzen ausgegeben, die unter dem gewählten Bereich liegen. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Trennfrequenz—Ausgabepegel—Pegel der Steilheit Einstellbare Werte blinken. 3 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Trennfrequenz: 50HZ—63HZ—80HZ—100HZ —125HZ—160HZ—200HZ Ausgangspegel: –24 bis +6 Pegel der Steilheit: –12— –24 BASS BOOST (Bassverstärkung) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um den gewünschten Pegel zu wählen. Während der Erhöhung bzw. Verminderung des Pegels wird 0 bis +6 angezeigt. 02 Verwenden Sie diese Funktion, um nur Hochfrequenztöne anzuhören. Nur Frequenzen, die höher als die Trennfrequenz des Hochpassfilters (HPF) sind, werden über die Lautsprecher ausgegeben. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Trennfrequenz—Pegel der Steilheit 3 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Trennfrequenz: OFF—50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Pegel der Steilheit: –12— –24 SLA (Programmquellen-Pegeleinstellung) Diese Funktion verhindert, dass sich die Lautstärke beim Wechseln der Programmquelle dramatisch ändert. ! Die Einstellungen basieren auf der UKW-Lautstärke, die unverändert bleibt. ! Der MW/LW-Lautstärkepegel kann ebenfalls mit dieser Funktion eingestellt werden. ! USB, iPod und APP sind automatisch auf die gleiche Einstellung gesetzt. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Lautstärke für die Programmquelle einzustellen. Einstellbereich: +4 bis –4 Deutsch FADER (Überblendeinstellung) Gebrauch dieses Geräts HPF SETTING (Hochpassfilter-Anpassung) SUB.W (Subwoofer Ein/Aus) De <QRD3247-B> 77 77 Black plate (78,1) Abschnitt Gebrauch dieses Geräts 02 Systemmenü Wichtig Die Funktion PW SAVE (Energiesparmodus) wird deaktiviert, wenn die Fahrzeugbatterie abgeklemmt wird und muss neu aktiviert werden, sobald die Batterie wieder angeschlossen wird. Wenn PW SAVE (Energiesparmodus) deaktiviert ist, kann das Gerät je nach Anschlussart Batterieleistung in Anspruch nehmen, sollte die Zündung des Fahrzeugs über keine ACC-Position (Zubehörposition) verfügen. 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die SystemmenüFunktion zu wählen. Nach der Auswahl können die folgenden Systemmenüfunktionen angepasst werden. LANGUAGE (Spracheinstellung) Gebrauch dieses Geräts 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. 12H (12-Stunden-Uhr)—24H (24-Stunden-Uhr) AUTO PI (Automatische PI-Suche) Das Gerät kann selbst bei einem Stationsabruf automatisch nach einer anderen Station mit derselben Programmierung suchen. 1 Drücken Sie M.C., um den Auto-PI-Suchlauf ein- oder auszuschalten. AUX (Zusatzeingang) Aktivieren Sie diese Einstellung, wenn ein zusätzliches, mit diesem Gerät verbundenes Gerät verwendet wird. 1 Drücken Sie M.C., um AUX ein- oder auszuschalten. DIMMER (Dimmer) 1 Drücken Sie M.C., um den Dimmer ein- bzw. auszuschalten. ! Sie können die Dimmer-Einstellung auch durch Drücken und Halten von /DIMMER ändern. MUTE MODE (Stummschaltung) 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. ENG (Englisch)—РУС (Russisch)—TUR (Türkisch) CLOCK SET (Einstellen der Uhrzeit) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um den Teil der Zeitanzeige zu wählen, der eingestellt werden soll. Stunden—Minuten 3 Drehen Sie M.C., um die Uhrzeit einzustellen. 12H/24H (Uhrzeitformat) 78 Die Klangwiedergabe dieses Geräts wird automatisch stummgeschaltet oder gedämpft, wenn das Signal eines Geräts mit Stummschaltung empfangen wird. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ! MUTE – Stummschaltung ! 20dB ATT – Dämpfung (20dB ATT hat eine stärkere Wirkung als 10dB ATT) ! 10dB ATT – Dämpfung PW SAVE (Energiesparmodus) Wenn Sie diese Funktion einschalten, reduzieren Sie den Verbrauch von Batterieleistung. ! Bei aktiviertem Energiesparmodus kann nur die Programmquelle eingeschaltet werden. 1 Drücken Sie M.C., um den Energiesparmodus ein- oder auszuschalten. Grundmenü 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. 2 Drücken und halten Sie SRC/OFF gedrückt, bis das Hauptmenü im Display erscheint. 3 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf INITIAL, um die angezeigte Option zu wählen. 4 Drehen Sie M.C., um die GrundmenüFunktion zu wählen. Nach der Auswahl können die folgenden Grundmenüfunktionen angepasst werden. FM STEP (UKW-Kanalraster) 1 Drücken Sie M.C., um die UKW-KanalrasterFunktion zu wählen. 100 (100 kHz)—50 (50 kHz) SP-P/O MODE (Heckausgang- und Preout-Einstellungen) Der Hecklautsprecher-Leitungsausgang und Cinch-Ausgang dieses Geräts können zum Anschluss eines Vollbereichslautsprechers oder Subwoofers verwendet werden. Wählen Sie für Ihren Anschluss eine geeignete Option. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ! REAR/SUB.W – Wählen Sie diese Option, wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang und ein Subwoofer an den Cinch-Ausgang angeschlossen ist. ! SUB.W/SUB.W – Wählen Sie diese Option, wenn ein Subwoofer an den Hecklautsprecher-Leitungsausgang ohne Verwendung eines zusätzlichen Verstärkers und ein Subwoofer an den Cinch-Ausgang angeschlossen ist. ! REAR/REAR – Wählen Sie diese Option, wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang und den Cinch-Ausgang angeschlossen ist. Wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang angeschlossen ist und der Cinch-Ausgang nicht verwendet wird, können Sie entweder REAR/SUB.W oder REAR/REAR auswählen. Systemmenü 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. 2 Drücken und halten Sie SRC/OFF gedrückt, bis das Hauptmenü im Display erscheint. De <QRD3247-B> 78 Black plate (79,1) Abschnitt Gebrauch dieses Geräts Installation 02 03 3 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 4 Drehen Sie M.C., um die SystemmenüFunktion zu wählen. Für detaillierte Informationen hierzu siehe Systemmenü auf Seite 78. 3 Drehen Sie M.C., um die Option DEMO OFF zur Anzeige zu bringen, und drücken Sie dann darauf, um Ihre Auswahl zu bestätigen. Hinweis AUX kann nur gewählt werden, wenn die AUXEinstellung eingeschaltet wurde. Für weitere Einzelheiten siehe AUX (Zusatzeingang) auf Seite 78. Umschalten der Anzeige Bei Anzeige einer unerwünschten Anzeige Schalten Sie die unerwünschte Anzeige anhand des unten beschriebenen Vorgangs aus. 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. OF F O Zündung mit Position ACC Zündung ohne Position ACC ! Der Einsatz dieses Geräts in einer anderen als der nachstehend angegebenen Betriebsumgebung kann einen Brand auslösen oder eine Funktionsstörung zur Folge haben: — Kraftfahrzeuge mit 12-Volt-Batterie und negativer Erdung. — Lautsprecher mit 50 W (Ausgabe) und 4 W bis 8 W (Impedanz). ! Um Kurzschluss, Überhitzung oder Funktionsstörungen zu vermeiden, halten Sie sich stets an die nachstehend aufgeführten Anweisungen: — Trennen Sie die Verbindung zur negativen Anschlussklemme der Fahrzeugbatterie, bevor Sie das Gerät installieren. — Sichern Sie die Kabel mit Kabelklemmen oder Klebeband. Zum Schutz der Verkabelung sollten die Kabel an allen Stellen, an denen sie mit Metallteilen in Berührung kommen, mit Isolierband umwickelt werden. — Bringen Sie die Kabel in sicherer Entfernung von beweglichen Fahrzeugkomponenten, wie z. B. Schalthebel und Sitzschienen, an. — Bringen Sie die Kabel in größtmöglicher Entfernung von Stellen an, die sich erhitzen, wie z. B. die Heizungsöffnung. — Führen Sie das gelbe Batteriekabel nicht durch ein Loch in den Motorraum, um die Verbindung mit der Fahrzeugbatterie herzustellen. — Kleben Sie freie Kabelanschlüsse mit Isolierband ab. — Kürzen Sie die Kabel nicht. — Entfernen Sie niemals die Isolierung des Stromkabels dieses Geräts, um die Stromzufuhr mit einem anderen Gerät zu teilen. Dadurch wird die Stromversorgungsleistung des Kabels beeinträchtigt. — Verwenden Sie eine Sicherung, die den vorgegebenen Leistungsmerkmalen entspricht. — Verdrahten Sie das negative Lautsprecherkabel niemals direkt mit der Erde. — Gruppieren Sie niemals die negativen Kabel mehrerer Lautsprecher. ! Wenn dieses Gerät eingeschaltet wird, liegen Steuersignale am blau/weißen Kabel an. Verbinden Sie dieses Kabel mit der Systemfernbedienung eines externen Leistungsverstärkers oder der Steuerklemme des Automatikantennenrelais des Kraftfahrzeugs (max. 300 mA, 12 V Gleichspannung). Wenn das Fahrzeug mit einer in die Heckscheibe integrierten Radioantenne ausgestattet ist, verbinden Sie das Kabel mit der Versorgungsklemme des Antennenboosters. ! Verbinden Sie das blau/weiße Kabel niemals mit der Leistungsklemme des externen Leistungsverstärkers. Darüber hinaus darf das Kabel keinesfalls mit der Leistungsklemme der Fahrzeugantenne verbunden werden. Andernfalls kann es zu einer Entleerung oder Funktionsstörung der Fahrzeugbatterie kommen. De <QRD3247-B> 79 Deutsch Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! Programmquellenname ! Programmquellname und Uhr Drücken Sie zur Auswahl M.C. STAR 2 Drücken Sie die Taste SRC/OFF, um AUX als Programmquelle zu wählen. 5 N 1 Verbinden Sie den Stereo-Mini-Klinkenstecker mit dem AUX-Eingang. 4 Drehen Sie M.C., um zu YES umzuschalten. Wichtig ! Bei der Installation des Geräts in einem Kraftfahrzeug, das am Zündschalter keine Position ACC aufweist, kann es je nach Anschlusstyp zu einer Entleerung der Fahrzeugbatterie kommen, wenn das rote Kabel nicht mit dem Anschluss verbunden wurde, der für die Erkennung des Zündschlüsselbetriebs verantwortlich ist. T Verwendung der AUXProgrammquelle Anschlüsse 79 Black plate (80,1) Abschnitt Installation 03 Installation ! Das schwarze Kabel gewährleistet die Erdung. Dieses Kabel wie auch die Erdungskabel anderer Produkte (insbesondere von Hochstromprodukten wie Leistungsverstärker) müssen separat verdrahtet werden. Anderenfalls kann es zu einem Brand oder einer Funktionsstörung kommen, wenn sich die Kabel versehentlich lösen. Netzkabel 2 Dieses Gerät 7 3 4 5 6 3 4 5 6 1 8 a 9 1 1 2 3 4 23 4 5 Antenneneingang Sicherung (10 A) Netzkabelzugang Eingang der festverdrahteten Fernbedienung Es besteht die Möglichkeit, einen (separat erhältlichen) festverdrahteten Fernbedienungsadapter anzuschließen. 5 Heck- oder Subwooferausgang 80 e b c d 1 Zum Netzzugang 2 Je nach Fahrzeugtyp können die Funktionen 3 und 5 variieren. Stellen Sie in diesem Fall sicher, dass der Anschluss von 4 nach 5 und 6 nach 3 erfolgt. 3 Gelb Reserveversorgung (oder Zubehör) 4 Gelb Verbindung mit der Klemme der konstanten 12-V-Spannungsversorgung. 5 Rot Zubehör (oder Reserveversorgung) 6 Rot Verbindung mit der Klemme der zündungsgesteuerten Spannungsversorgung (12 V Gleichspannung). 7 Verbinden Sie jeweils Anschlüsse derselben Farbe miteinander. 8 Schwarz (Fahrgestell-Erdung) 9 Blau/Weiß Die Pin-Position des ISO-Anschlusses variiert je nach Fahrzeugtyp. Wird Pin 5 zur Steuerung der Antenne verwendet, verbinden Sie 9 und b. Verbinden Sie in jedem anderen Fahrzeugtyp niemals 9 und b. a Blau/Weiß Verbindung mit der Systemsteuerungsklemme des Leistungsverstärkers (max. 300 mA, 12 V Gleichspannung). b Blau/Weiß Verbindung mit der Steuerungsklemme des Automatikantennenrelais (max. 300 mA 12 V Gleichspannung). c Gelb/Schwarz Wenn Sie ein Gerät mit Stummschaltfunktion verwenden, verbinden Sie diesen Draht mit dem Draht der Audio-Stummschaltung dieses Geräts. Andernfalls sollte der Draht der Audio-Stummschaltung (Mute) frei bleiben. d Lautsprecherkabel Weiß: Vorn links + Weiß/Schwarz: Vorn links * Grau: Vorn rechts + Grau/Schwarz: Vorn rechts * Grün: Hinten links + oder Subwoofer + Grün/Schwarz: Hinten links * oder Subwoofer * Violett: Hinten rechts + oder Subwoofer + Violett/Schwarz: Hinten rechts * oder Subwoofer * e ISO-Anschluss Bei manchen Fahrzeugtypen kann der ISOAnschluss zweigeteilt sein. Stellen Sie in diesem Fall sicher, dass zu beiden Anschlüssen Verbindungen hergestellt werden. Hinweise ! Ändern Sie das Grundeinstellmenü dieses Geräts. Siehe SP-P/O MODE (Heckausgangund Preout-Einstellungen) auf Seite 78. Die Subwoofer-Ausgabe dieses Geräts erfolgt in Mono. ! Bei Verwendung eines 70-W-Subwoofers (2 W) muss sichergestellt werden, dass der Subwoofer am violetten und violett/schwarzen-Anschluss dieses Geräts angeschlossen wird. Schließen Sie nichts an den grünen und grün/schwarzen-Anschluss an. Leistungsverstärker (separat erhältlich) Führen Sie diese Verkabelungen beim Gebrauch eines optionalen Verstärkers durch. 3 1 5 2     4 5 1 Systemfernbedienung Verbindung mit blau/weißem Kabel. 2 Leistungsverstärker (separat erhältlich) 3 Verbindung mit Cinch-Kabeln (separat erhältlich) 4 Zum Heck- oder Subwooferausgang 5 Hecklautsprecher oder Subwoofer Installation Wichtig ! Überprüfen Sie vor der endgültigen Installation alle Anschlüsse und Systeme. ! Die Verwendung nicht zugelassener Teile kann eine Funktionsstörung zur Folge haben. ! Wenden Sie sich an Ihren Fachhändler, wenn für die Installation Löcher gebohrt oder andere Änderungen am Fahrzeug vorgenommen werden müssen. ! Installieren Sie dieses Gerät keinesfalls an folgenden Orten: — Orte, an denen das Gerät die Steuerung des Fahrzeugs behindern könnte. — Orte, an denen das Gerät die Insassen des Fahrzeugs im Anschluss an eine Schnellbremsung verletzen könnte. De <QRD3247-B> 80 Black plate (81,1) Abschnitt Installation Installation ! Der Halbleiterlaser kann durch Überhitzung beschädigt werden. Installieren Sie dieses Gerät deshalb in sicherer Entfernung von Hitzequellen, wie z. B. Heizöffnungen. ! Optimale Leistung kann durch eine Installation des Geräts in einem Winkel unter 60° erzielt werden. 1 Setzen Sie den Einpassungsring ein. Installation mit Halterung 1 Bringen Sie die Halterung am Armaturenbrett an. Wählen und biegen Sie nach dem Einsetzen der Halterung im Armaturenbrett die Klammern entsprechend der Dicke des Armaturenbrettmaterials. (Setzen Sie diese Einheit so fest wie möglich mithilfe der oberen und unteren Klammern ein. Biegen Sie die Klammern 90 Grad, um einen fest Halt zu gewährleisten.) 1 1 1 Einpassungsring 1 1 Einpassungsring Entfernen der Halterung Dieser Vorgang ist der gleiche wie unter “Vor dem Anbringen dieser Einheit”. Für detaillierte Informationen hierzu siehe Vor dem Anbringen dieser Einheit auf Seite 81. 2 Führen Sie die mitgelieferten Extraktionsschlüssel an beiden Geräteseiten ein, bis sie in der richtigen Position einrasten. Reichlich Platz lassen 3 Entfernen Sie den Einpassungsring. 60° ! Um beim Gebrauch des Geräts eine ordnungsgemäße Wärmezerstreuung zu gewährleisten, ist bei der Installation genügend Freiraum hinter der Rückseite vorzusehen. Lose Kabel sind aufzuwickeln, damit sie die Lüftung nicht behindern. 1 Halterung (werkseitig mitgelieferte Teile) Vor dem Anbringen dieser Einheit 03 5 cm 2 5 cm 5cm cm ! Verwenden Sie für die Montage im Handel erhältliches Zubehör. Installationsmethode Diese Einheit kann anhand einer der Methoden in der unten stehenden Liste ordnungsgemäß installiert werden: ! Installation mit Halterung ! Bei Anbringen mithilfe der Schraubenlöcher auf beiden Seiten der Einheit 3 Ziehen Sie das Gerät aus der Halterung. Nehmen Sie die Halterung ab. 2 Installieren Sie dieses Gerät. 1 % Befestigen Sie die Einheit an der werkseitig-angebrachten Radiomontageklammer. Richten Sie das Gerät so aus, dass seine Schraubenlöcher mit den Schraubenlöchern der Klammer übereinstimmen, und ziehen Sie die drei Schrauben auf jeder Seite fest. Deutsch 1 Armaturenbrett 2 Halterung (werkseitig mitgelieferte Teile) Bei Anbringen mithilfe der Schraubenlöcher auf beiden Seiten der Einheit 1 1 Armaturenbrett De <QRD3247-B> 81 81 Black plate (82,1) Abschnitt Installation 03 Zusätzliche Informationen Fehlerbehebung Fehlermeldungen Symptome sind in Fett, Ursachen in normalem, nicht eingerückten Text und Abhilfemaßnahmen in normalem, eingerückten Text geschrieben. Vor der Kontaktaufnahme mit Ihrem Händler oder der nächstgelegenen Pioneer-Kundendienststelle sollten Sie sich die angezeigte Fehlermeldung notieren. Fehlermeldungen sind in Fett, Ursachen in normalem, nicht eingerückten Text und Abhilfemaßnahmen in normalem, eingerückten Text geschrieben. Das Display schaltet automatisch in die normale Anzeige um. 1 2 Sie haben keinen Bedienvorgang innerhalb von 30 Sekunden durchgeführt. Wiederholen Sie den Vorgang. AMP ERROR Ja nach Wiederholbereich kann sich der ausgewählte Bereich ändern, sobald ein anderer Ordner oder Musiktitel ausgewählt wird oder während des schnellen Vor- und Rücklaufs. Wählen Sie den Wiederholbereich erneut aus. Betriebsstörung des Geräts oder falsche Lautsprecherverbindung; Schutzschaltung ist aktiviert. Überprüfen Sie die Lautsprecherverbindung. Wenn die Meldung selbst nach dem Aus-/ Einschalten des Motors weiterhin angezeigt wird, wenden Sie sich zur Unterstützung an Ihren Händler oder eine Pioneer-Kundendienststelle. Ein Unterordner wird nicht wiedergegeben. 3 4 1 Sollte die Sperrklinke im Weg sein, biegen Sie sie nach unten. 2 Werkseitig bereitgestellte Radio-Montageklammer 3 Trägerschrauben (5 mm × 8 mm) 4 Armaturenbrett oder Konsole Allgemeines Der Wiederholbereich ändert sich unerwartet. Unterordner können nicht wiedergegeben werden, wenn FLD (Ordner-Wiederholung) ausgewählt ist. Wählen Sie einen anderen Wiederholbereich. NO XXXX erscheint, wenn sich die Anzeige ändert (z. B. NO TITLE). Es sind keine Textinformationen eingebettet. Schalten Sie die Anzeige um oder spielen Sie einen anderen Titel bzw. eine andere Datei ab. Im Gerät ist eine Fehlfunktion aufgetreten. Es liegen Funkstörungen vor. Sie verwenden ein Gerät, wie z. B. ein Mobiltelefon, welches Störgeräusche verursachen könnte. Lassen Sie einen ausreichenden Abstand zwischen dieser Einheit und den Geräten, die die Funkstörung verursachen. CD-Player ERROR-07, 11, 12, 17, 30 Die Disc ist verschmutzt. Reinigen Sie die Disc. Die Disc ist verkratzt. Wechseln Sie die Disc aus. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Es liegt ein elektrischer oder mechanischer Fehler vor. Schalten Sie die Zündung aus (OFF) und wieder ein (ON) oder schalten Sie auf eine andere Programmquelle um und dann wieder zum CDPlayer zurück. ERROR-15 Die eingelegte Disc ist leer. Wechseln Sie die Disc aus. 82 De <QRD3247-B> 82 Black plate (83,1) Anhang Zusätzliche Informationen ERROR-23 Nicht unterstütztes CD-Format. Wechseln Sie die Disc aus. FORMAT READ Nach dem Wiedergabestart ist der Ton in manchen Fällen erst nach einer Verzögerung zu hören. Warten Sie bis die Anzeige erlischt und Sie einen Ton hören. NO AUDIO Die eingelegte Disc enthält keine abspielbaren Dateien. Wechseln Sie die Disc aus. SKIPPED Die eingelegte Disc enthält Dateien mit DRM-Schutz (digitale Rechteverwaltung). Die geschützten Dateien werden übersprungen. PROTECT Alle Dateien auf der eingelegten Disc weisen einen DRM-Schutz (digitale Rechteverwaltung) auf. Wechseln Sie die Disc aus. Zusätzliche Informationen CHECK USB ERROR-23 Das USB-Speichermedium wurde nicht mit FAT12, FAT16 oder FAT32 formatiert. Das USB-Speichermedium sollte mit FAT12, FAT16 oder FAT32 formatiert sein. Das verbundene USB-Speichermedium enthält Dateien mit DRM-Schutz. Die geschützten Dateien werden übersprungen. Das angeschlossene USB-Speichermedium verbraucht mehr als den maximal zulässigen Stromverbrauch. Trennen Sie das USB-Speichermedium von diesem Gerät und verwenden Sie es nicht mehr in Verbindung mit dem Gerät. Drehen Sie den Zündschlüssel in die Position OFF (Aus) und anschließend in die Position ACC oder ON (Ein). Schließen Sie dann nur ein kompatibles USBSpeichermedium an. PROTECT CHECK USB Alle Dateien auf dem verbundenen USB-Speichermedium sind mit DRM geschützt. Tauschen Sie das USB-Speichermedium aus. Der iPod funktioniert ordnungsgemäß, wird jedoch nicht geladen. Kontrollieren Sie, dass das iPod-Kabel nicht kurzgeschlossen (d. h. zwischen Gegenständen aus Metall eingeklemmt) wurde. Schalten Sie anschließend die Zündung aus (OFF) und wieder ein (ON) oder trennen Sie die Verbindung zum iPod und schließen Sie den iPod dann wieder an. Es wurde ein USB-Speichermedium mit aktivierter Sicherheitsfunktion angeschlossen. Halten Sie sich an die Anweisungen in der Bedienungsanleitung des USBSpeichermediums, um die Sicherheitsfunktion zu deaktivieren. SKIPPED N/A USB Das angeschlossene USB-Gerät wird von diesem Gerät nicht unterstützt. ! Schließen Sie ein dem Standard USBMassenspeicher-Klasse entsprechendes Gerät an. ! Trennen Sie das Gerät ab und schließen Sie ein kompatibles USB-Speichermedium an. FORMAT READ Nach dem Wiedergabestart ist der Ton in manchen Fällen erst nach einer Verzögerung zu hören. Warten Sie bis die Anzeige erlischt und Sie einen Ton hören. NO AUDIO Es sind keine Musiktitel vorhanden. Übertragen Sie die Audio-Dateien auf das USBSpeichermedium und schließen Sie das Gerät dann an. Der USB-Anschluss oder das USB-Kabel wurde kurzgeschlossen. Stellen Sie sicher, dass die USB-Klemme oder das USB-Kabel nicht eingeklemmt oder beschädigt ist. Die iPod-Firmwareversion ist veraltet. Aktualisieren Sie die iPod-Version. iPod gestört. Trennen Sie das Kabel vom iPod. Sobald das Hauptmenü auf dem iPod erscheint, schließen Sie ihn erneut an und setzen Sie ihn zurück. STOP Die aktuelle Liste enthält keine Musiktitel. Wählen Sie eine Liste, die Musiktitel enthält. NOT FOUND Keine entsprechenden Musiktitel gefunden. Übertragen Sie Musiktitel auf den iPod. ERROR-19 Kommunikation gestört. Führen Sie einen der folgenden Bedienvorgänge durch: – Schalten Sie die Zündung aus (OFF) und wieder ein (ON). – Trennen Sie das USB-Speichermedium vom Gerät. – Schalten Sie auf eine andere Programmquelle um. Kehren Sie anschließend wieder zur Programmquelle USB zurück. Anwendung START UP APP Die Anwendung ist noch nicht betriebsbereit. Folgen Sie den auf dem Bildschirm angezeigten Anweisungen. Deutsch CHECK USB USB-Speichermedium/iPod ERROR-16 iPod gestört. Trennen Sie das Kabel vom iPod. Sobald das Hauptmenü auf dem iPod erscheint, schließen Sie ihn erneut an und setzen Sie ihn zurück. De <QRD3247-B> 83 83 Black plate (84,1) Anhang Zusätzliche Informationen Handhabungsrichtlinien Discs und Player Verwenden Sie ausschließlich Discs, die eines der folgenden zwei Logos aufweisen: Zusätzliche Informationen Kondensation kann eine vorübergehende Störung der Player-Leistung zur Folge haben. Warten Sie in diesem Fall etwa eine Stunde ab, bis sich der Player an die höheren Temperaturen angepasst hat. Zudem sollten feuchte Discs mit einem weichen Tuch trockengerieben werden. Unter Umständen ist eine Disc-Wiedergabe nicht möglich. Das kann auf die spezifischen Eigenschaften der Disc, das Disc-Format, die für die Aufzeichnung verwendete Software, die Wiedergabeumgebung, die Lagerbedingungen usw. zurückzuführen sein. Verwenden Sie 12-cm-Discs. Verwenden Sie ausschließlich herkömmliche, runde Discs. Die folgenden Disc-Typen können nicht mit diesem Gerät verwendet werden: ! DualDiscs ! 8-cm-Discs: Versuche solche Discs mit einem Adapter zu verwenden, können zu Fehlfunktionen des Geräts führen. ! Discs in ungewöhnlichen Formen ! Andere Discs als CDs ! Beschädigte Discs einschließlich Discs mit Rissen, Verwellungen und abgeplatzten Teilen ! CD-R/RW-Discs mit nicht abgeschlossener Aufzeichnung Berühren Sie unter keinen Umständen die DiscOberfläche mit den aufgezeichneten Daten. Bewahren Sie die Discs bei Nichtgebrauch in deren Hülle auf. Kleben Sie keine Etiketten auf Discs, beschriften Sie sie nicht und wenden Sie keine Chemikalien auf die Disc-Oberfläche an. Erschütterungen aufgrund von Unebenheiten der Fahrbahn können die Disc-Wiedergabe unterbrechen. Bei Verwendung von bedruckbaren Discs, beachten Sie die Anleitung und die Warnhinweise der Disc. Je nach Beschaffenheit der Discs, können Sie eventuell nicht eingelegt oder ausgeworfen werden. Die Verwendung solcher Discs kann zu einer Beschädigung dieses Gerätes führen. Bringen Sie keine handelsüblichen Etiketten oder andere Materialien auf den Discs an. ! Die Discs können sich verformen und werden nicht wiedergegeben. ! Die Etiketten können sich während der Wiedergabe lösen und den Auswurf behindern, wodurch das Gerät beschädigt werden könnte. USB-Speichermedium Verbindungen über einen USB-Hub werden nicht unterstützt. Schließen Sie ausschließlich USB-Speichermedien an. Sorgen Sie für eine sichere Befestigung des USBSpeichermediums während der Fahrt. Lassen Sie das USB-Speichermedium nicht auf den Boden fallen, wo es unter der Bremse oder dem Gaspedal eingeklemmt werden könnte. Je nach USB-Speichermedium können folgende Probleme auftreten: ! Die Bedienung kann unterschiedlich sein. ! Das Speichergerät wird unter Umständen nicht erkannt. ! Dateien werden eventuell nicht richtig wiedergegeben. ! Das Gerät kann Störgeräusche verursachen, während Sie Radio hören. Kompatible komprimierte Audio-Formate (Discs, USBSpeichermedien) WMA Dateierweiterung: .wma Bitrate: 48 Kbit/s bis 320 Kbit/s (CBR - Konstante Bitrate), 48 Kbit/s bis 384 Kbit/s (VBR - Variable Bitrate) Abtastfrequenz: 32 kHz; 44,1 kHz; 48 kHz Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream mit Video: Nicht kompatibel iPod Bewahren Sie den iPod nicht an Orten auf, an denen hohe Temperaturen herrschen. MP3 Dateierweiterung: .mp3 Sorgen Sie für eine sichere Befestigung des iPods während der Fahrt. Lassen Sie den iPod nicht auf den Boden fallen, wo er unter der Bremse oder dem Gaspedal eingeklemmt werden könnte. Bitrate: 8 Kbit/s bis 320 Kbit/s (CBR), VBR Zu den iPod-Einstellungen ! Wenn ein iPod an dieses Gerät angeschlossen wird, wird die Equalizer-Einstellung des iPods automatisch deaktiviert, um die Akustik zu optimieren. Beim Trennen der Verbindung wird der Equalizer auf die ursprüngliche Einstellung zurückgesetzt. ! Bei der Verwendung dieses Geräts lässt sich die Wiederholfunktion auf dem iPod nicht ausschalten. Wenn ein iPod mit diesem Gerät verbunden ist, wird die Funktion zur Wiederholung aller Titel automatisch aktiviert. Kompatible ID3-Tag-Version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3-Tag-Version 2.x erhält Vorrang vor Version 1.x) Auf dem iPod gespeicherter Text, der nicht mit diesem Gerät kompatibel ist, wird nicht angezeigt. Abtastfrequenz: 8 kHz bis 48 kHz (32 kHz; 44,1 kHz; 48 kHz für Emphase) M3u-Spielliste: Nicht kompatibel MP3i (MP3 interaktiv), mp3 PRO: Nicht kompatibel WAV Dateierweiterung: .wav Quantisierungsbits: 8 und 16 (LPCM), 4 (MS ADPCM) Abtastfrequenz: 16 kHz bis 48 kHz (LPCM); 22,05 kHz und 44,1 kHz (MS ADPCM) Wischen Sie die Discs zum Reinigen mit einem weichen Tuch von der Mitte zum Rand hin ab. 84 De <QRD3247-B> 84 Black plate (85,1) Anhang Zusätzliche Informationen ! Diese Funktion kann nicht mit USB MTP verwendet werden. Zusätzliche Informationen Von Dateinamen (einschließlich der Dateierweiterung) bzw. von Ordnernamen können jeweils nur die ersten 32 Zeichen angezeigt werden. Damit kyrillische Buchstaben auf diesem Gerät angezeigt werden können, müssen diese mit einem der folgenden Zeichensätze codiert worden sein: ! Unicode (UTF-8, UTF-16) ! Andere Zeichensätze als Unicode, die in einer Windows-Umgebung verwendet und in den Sprachoptionen auf Russisch eingestellt wurden. Je nach der Anwendung, die für die Codierung der WMA-Dateien verwendet wurde, funktioniert dieses Gerät ggf. nicht ordnungsgemäß. Datenübertragungen im Paketverfahren: Nicht kompatibel Ungeachtet der Länge der Leerstellen, die die Originalaufnahme zwischen den einzelnen Musiktiteln aufweist, wird bei der Wiedergabe von komprimierten Audio-Discs stets eine kurze Pause zwischen den Titeln eingefügt. USB-Speichermedium Abspielbare Ordnerstruktur: bis zu acht Ebenen (der Einfachheit halber sollte die Ordnerstruktur jedoch aus weniger als zwei Ebenen bestehen). Abspielbare Ordner: bis zu 500 Abspielbare Dateien: bis zu 15 000 Wiedergabe von urheberrechtlich geschützten Dateien: Nicht kompatibel Partitioniertes USB-Speichermedium: Es kann nur die erste Partition wiedergegeben werden. Beim Start der Wiedergabe von Audio-Dateien auf einem USB-Speichermedium, das eine komplexe Ordnerhierarchie aufweist, ist der Ton u. U. erst mit einiger Verzögerung zu hören. Disc VORSICHT Abspielbare Ordnerstruktur: bis zu acht Ebenen (der Einfachheit halber sollte die Ordnerstruktur jedoch aus weniger als zwei Ebenen bestehen). Abspielbare Ordner: bis zu 99 Abspielbare Dateien: bis zu 999 Dateisystem: Konformität mit ISO 9660 Stufe 1 und 2, Romeo, Joliet ! Pioneer kann nicht die Kompatibilität mit allen USB-Speichermedien gewährleisten und übernimmt keine Verantwortung für eventuelle Datenverluste auf Media-Playern, Smartphones oder anderen Geräten, die mit diesem Gerät verwendet werden. ! Bewahren Sie keine Discs oder USB-Speichermedien an Orten auf, an dem erhöhte Temperaturen herrschen. iPod-Kompatibilität Dieses Gerät unterstützt nur die folgenden iPodModelle. Hergestellt für ! iPod touch (5. Generation) ! iPod touch (4. Generation) ! iPod touch (3. Generation) ! iPod touch (2. Generation) ! iPod touch (1. Generation) ! iPod classic ! iPod mit Video ! iPod nano (7. Generation) ! iPod nano (6. Generation) ! iPod nano (5. Generation) ! iPod nano (4. Generation) ! iPod nano (3. Generation) ! iPod nano (2. Generation) ! iPod nano (1. Generation) ! iPhone 5 ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone Je nach iPod-Generation bzw. -Version können einige Funktionen nicht verfügbar sein. Je nach der iPod-Softwareversion gestaltet sich die Bedienung ggf. etwas unterschiedlich. Benutzer eines iPod mit Lightning-Anschluss sollten das (im iPod-Lieferumfang enthaltene) Lightning-auf-USB-Kabel verwenden. Benutzer eines iPod mit Dock-Anschluss sollten ein CD-IU51 verwenden. Weitere Einzelheiten erfahren Sie bei Ihrem Fachhändler. Informationen bezüglich der Datei-/Formatkompatibilität finden Sie im Handbuch Ihres iPods. Multi-Session-Wiedergabe: Kompatibel Hörbücher, Podcasts: Kompatibel VORSICHT Pioneer haftet in keinem Fall für den Verlust von Daten auf einem iPod, selbst dann nicht, wenn der Datenverlust während der Verwendung dieses Geräts aufgetreten ist. Reihenfolge der Audio-Dateien Der Benutzer kann keine Ordnernummern zuweisen und auch die Wiedergabereihenfolge mit diesem Gerät nicht bestimmen. Beispiel einer Datenträger-Struktur 01 02 1 2 03 3 4 04 5 6 05 Stufe 1 Stufe 2 Stufe 3 Stufe 4 : Ordner : Komprimierte Audio-Datei 01 bis 05: Ordnernummer 1 bis 6: Wiedergabereihenfolge Disc Die bei der Ordnerauswahl oder einem anderen Bedienvorgang angewendete Reihenfolge kann sich je nach der verwendeten Codierungs- bzw. Schreibsoftware ändern. Deutsch Nach dem Wiedergabestart kann es bei Audio-Dateien, in die Bilddaten eingebettet wurden bzw. bei Audio-Dateien auf einem USB-Speichermedium mit einer komplexen Ordnerhierachie zu einer kurzen Verzögerung kommen. Zusätzliche Informationen USB-Speichermedium Die Wiedergabereihenfolge entspricht der Aufzeichnungsreihenfolge auf dem USB-Speichermedium. Für die Bestimmung der Wiedergabereihenfolge wird folgende Vorgehensweise empfohlen: 1 Erstellen Sie Dateinamen basierend auf Zahlen, um dadurch die gewünschte Wiedergabereihenfolge festzulegen (z. B. 001xxx.mp3 oder 099yyy.mp3). 2 Speichern Sie diese Dateien in einem Ordner. De <QRD3247-B> 85 85 Black plate (86,1) Anhang Zusätzliche Informationen 3 Speichern Sie den Ordner mit den Dateien auf dem USB-Speichermedium. Je nach Systemumgebung ist eine Festlegung der Dateiwiedergabereihenfolge jedoch u. U. nicht möglich. Die Dateireihenfolge bei tragbaren USB-AudioPlayern unterscheidet sich jeweils vom verwendeten Player. Russischer Zeichensatz D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я D: Anzeige C: Zeichen Copyrights und Marken MP3 Die Bereitstellung dieses Produkts erfolgt in Verbindung mit einer Lizenz zur privaten, nichtkommerziellen Nutzung und impliziert weder die Übertragung einer Lizenz noch die Einräumung eines Rechts zur Verwendung dieses Produkts in kommerziellen (d. h. ertragsorientierten) LiveProgrammen (leitungsbasiert, per Satellit, Kabel und/oder über jedes beliebige andere Medium), zum Broadcasting/Streaming über das Internet, über Intranets und/oder andere Netzwerke oder in anderen elektronischen Inhalt-Vertriebssyste- 86 Zusätzliche Informationen men, z. B. „Pay-Audio”- oder „Audio-on-demand”-Anwendungen. Für eine derartige Nutzung ist eine separate Lizenz erforderlich. Detaillierte Informationen hierzu finden Sie unter http://www.mp3licensing.com. WMA Windows Media ist eine eingetragene Marke oder eine Marke der Microsoft Corporation in den USA und/oder anderen Ländern. Dieses Produkt enthält Technologie, die Eigentum der Microsoft Corporation ist und nicht ohne Lizenz von Microsoft Licensing, Inc. vertrieben werden darf. iPod und iPhone iPhone, iPod, iPod classic, iPod nano und iPod touch sind in den USA sowie in anderen Ländern eingetragene Marken von Apple Inc. Lightning ist ein Warenzeichen der Apple Inc. Die Kennzeichnungen „Made for iPod” und „Made for iPhone” bedeuten, dass ein elektronisches Zubehörteil spezifisch zum Anschluss an iPod oder iPhone konstruiert wurde und entsprechend vom Entwickler als die Leistungsstandards von Apple erfüllend zertifiziert wurde. Apple übernimmt keine Verantwortung für die richtige Funktion dieses Geräts oder seine Erfüllung von Sicherheits- oder anderen Vorschriften. Bitte beachten Sie, dass der Gebrauch dieses Zubehörteils in Verbindung mit einem iPod oder iPhone die drahtlose Leistung beeinträchtigen kann. Androidä Android ist eine Marke von Google Inc. Technische Daten Allgemein Stromversorgung ............. 14,4 V Gleichspannung (Toleranz 10,8 V bis 15,1 V) Erdungssystem ................ Negativ Maximale Leistungsaufnahme ................................... 10,0 A Abmessungen (B × H × T): DIN Einbaugröße .................... 178 mm × 100 mm × 157 mm Frontfläche ...................... 188 mm × 118 mm × 25 mm D Einbaugröße .................... 178 mm × 100 mm × 165 mm Frontfläche ...................... 170 mm × 96 mm × 17 mm Gewicht ........................... 1,2 kg Audio Max. Ausgangsleistung .... 50 W × 4 70 W × 1/2 W (für Subwoofer) Dauer-Ausgangsleistung ................................... 22 W × 4 (50 Hz bis 15 000 Hz, 5 % THD, bei 4-W-Last, beide Kanäle betrieben) Lastimpedanz .................. 4 W (4 W bis 8 W zulässig) Maximaler Preout-Ausgangspegel ................................... 2,0 V Loudness-Kontur ............. +10 dB (100 Hz), +6,5 dB (10 kHz) (Lautstärke: –30 dB) Equalizer (5-Band Graphic Equalizer): Frequenz .......................... 80 Hz/250 Hz/800 Hz/2,5 kHz/ 8 kHz Entzerrungsbereich .......... ±12 dB (Inkrement 2 dB) Subwoofer (Mono): Frequenz .......................... 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Steilheit ........................... –12 dB/Okt., –24 dB/Okt. Verstärkung ..................... +6 dB bis –24 dB Phase .............................. Normal/Gegen CD-Player Typ ................................... Compact-Disc-Digital-Audiosystem Kompatible Discs ............. Compact Disc Signal-Rauschabstand ..... 94 dB (1 kHz) (IEC-A-Netz) Anzahl der Kanäle ............ 2 (Stereo) MP3-Decodiermodus ....... MPEG-1 und 2 Audio Layer 3 WMA-Decodiermodus ...... Vers. 7, 7.1, 8, 9, 10, 11, 12 (2Kanal-Audio) (Windows Media Player) WAV-Signalformat ............ Lineare PCM und MS ADPCM (nicht komprimiert) USB USB-Standard-Spezifikation ................................... USB 2.0 Full Speed Maximale Stromversorgung ................................... 1 A USB-Klasse ..................... MSC (Massenspeicher-Klasse) Dateisystem ..................... FAT12, FAT16, FAT32 MP3-Decodiermodus ....... MPEG-1 und 2 Audio Layer 3 WMA-Decodiermodus ...... Vers. 7, 7.1, 8, 9, 10, 11, 12 (2Kanal-Audio) (Windows Media Player) WAV-Signalformat ............ Lineare PCM und MS ADPCM (nicht komprimiert) UKW-Tuner Frequenzbereich .............. 87,5 MHz bis 108,0 MHz Nutzempfindlichkeit ......... 9 dBf (0,8 µV/75 W, Mono, Signal-Rauschabstand: 30 dB) Signal-Rauschabstand ..... 72 dB (IEC-A-Netz) MW-Tuner Frequenzbereich .............. 531 kHz bis 1 602 kHz Nutzempfindlichkeit ......... 25 µV (Signal-Rauschabstand: 20 dB) Signal-Rauschabstand ..... 62 dB (IEC-A-Netz) LW-Tuner Frequenzbereich .............. 153 kHz bis 281 kHz Nutzempfindlichkeit ......... 28 µV (Signal-Rauschabstand: 20 dB) Signal-Rauschabstand ..... 62 dB (IEC-A-Netz) Hinweis Änderungen der technischen Daten und des Designs vorbehalten. De <QRD3247-B> 86 Black plate (87,1) Deutsch De <QRD3247-B> 87 87 Black plate (88,1) Hoofdstuk Vóór u begint 01 Hartelijk dank voor uw keuze voor dit Pioneer-product Lees deze handleiding voordat u het product in gebruik neemt zodat u het goed leert gebruiken. Lees vooral de gedeelten die met WAARSCHUWING en LET OP gemarkeerd zijn aandachtig. Bewaar deze handleiding na het lezen op een veilige, voor de hand liggende plaats zodat u hem indien nodig altijd kunt raadplegen. Vóór u begint Informatie over dit toestel De tuner van dit toestel kan worden afgestemd op frequenties die gebruikt worden in West-Europa, Azië, het Midden-Oosten, Afrika en Oceanië. In andere gebieden is de ontvangst wellicht slecht. De RDS-functie (Radio Data System) werkt alleen in gebieden waar FM-zenders RDSinformatie uitzenden. WAARSCHUWING Deponeer dit product niet bij het gewone huishoudelijk afval wanneer u het wilt verwijderen. Er bestaat een speciaal wettelijk voorgeschreven verzamelsysteem voor de juiste behandeling, het opnieuw bruikbaar maken en de recycling van gebruikte elektronische producten. In de lidstaten van de EU en in Zwitserland en Noorwegen kunnen particulieren afgedankte elektronische producten gratis bij de daarvoor bestemde verzamelplaatsen inleveren. Als u een soortgelijk nieuw product koopt, kunt u het afgedankte product ook bij uw verkooppunt inleveren. Als u in een ander land woont, neem dan contact op met de plaatselijke overheid voor informatie over het weggooien van afgedankte producten. Op die manier zorgt u ervoor dat uw afgedankte product op de juiste wijze wordt verwerkt, hergebruikt en gerecycled, zonder schadelijke gevolgen voor het milieu en de volksgezondheid. 88 ! Probeer het product niet zelf te monteren en voer er geen onderhoud aan uit. Montage of onderhoud van het product door personen zonder technische opleiding en ervaring met elektronische apparatuur en auto-accessoires kan gevaarlijk zijn, en kan een elektrische schok, verwonding of andere gevaren veroorzaken. ! Bedien het toestel niet tijdens het rijden. Als u knoppen op het toestel wilt bedienen, moet u het voertuig eerst van de weg halen en op een veilige plaats parkeren. LET OP Dit apparaat is geclassificeerd als een klasse 1 laserproduct onder de veiligheidsnormen voor laserproducten, IEC 60825-1:2007. KLASSE 1 LASERPRODUCT Bij problemen Neem contact op met uw leverancier of het dichtstbijzijnde erkende Pioneer-servicecentrum als het toestel niet naar behoren functioneert. LET OP ! Zorg ervoor dat het toestel niet met vloeistof in aanraking komt. Een elektrische schok kan daarvan het gevolg zijn. Bovendien kan contact met vloeistoffen rookvorming, oververhitting en andere schade aan het toestel veroorzaken. ! De Pioneer CarStereo-Pass wordt alleen in Duitsland gebruikt. ! Zet het volume nooit zo hoog dat u geluiden buiten het voertuig niet meer kunt horen. ! Zorg dat het toestel niet wordt blootgesteld aan vocht. Nl <QRD3247-B> 88 Black plate (89,1) Hoofdstuk Gebruik van het toestel Hoofdtoestel 1 2 Gebruik van het toestel 2 Display-indicaties 3 4 2 1 5 3 4 5 7 9 6 8 a 1 6 7 1 h (uitwerpen) 2 iPod 89 3 1/ 4 Laadsleuf voor disc 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d 9 MULTI-CONTROL (M.C.) 2 3 Bijkomende informatie 4 TA (verkeersberichten) 5 TP (verkeersprogramma-identificatie) 6 7 8 (iPod-bediening) a (terug)/DIMMER (dimmer) b (lijst) AUX-ingang (3,5 mm-stereoplug) d USB-poort 9 a b (sound retriever) LOC (automatisch afstemmen op lokale zenders) (herhalen) (willekeurig) Basisinformatie ! Tuner: frequentieband en frequentie ! RDS: programmaservicenaam, PTY-informatie en andere tekstinformatie ! Cd-speler, USB-opslagapparaat en iPod: verstreken weergavetijd en tekstinformatie Licht op wanneer er een menu of mappen op een lager niveau bestaan. LET OP Sluit een USB-opslagapparaat via een Pioneer USB-kabel (CD-U50E, optioneel) op dit toestel aan. Sluit het niet rechtstreeks op dit toestel aan omdat het dan uitsteekt en verwondingen of beschadigingen kan veroorzaken. Instellingenmenu 3 Druk op M.C. om uw keuze te bevestigen. 4 Volg deze stappen om het menu in te stellen. Om verder te gaan naar de volgende menuoptie, moet u uw selectie bevestigen. LANGUAGE (taalinstelling) Dit toestel kan Engelse, Russische of Turkse tekstinformatie bij een gecomprimeerd audiobestand weergeven. ! Als de gebruikte taal niet overeenkomt met de taalinstelling van dit toestel, wordt tekst wellicht niet correct weergegeven. ! Het is mogelijk dat sommige tekens niet juist worden weergegeven. 1 Draai aan M.C. en selecteer de gewenste instelling. ENG (Engels)—РУС (Russisch)—TUR (Turks) 2 Druk op M.C. om de selectie te bevestigen. CLOCK SET (klok) 1 2 3 4 Draai aan M.C. om het uur in te stellen. Druk op M.C. om de minuut te selecteren. Draai aan M.C. om de minuut in te stellen. Druk op M.C. om de selectie te bevestigen. FM STEP (FM-afstemstap) Gebruik FM STEP om de FM-afstemstap in te stellen (afstemstap bij het zoeken). 1 Draai aan M.C. en selecteer de FM-afstemstap. 100 (100 kHz)—50 (50 kHz) 2 Druk op M.C. om de selectie te bevestigen. QUIT verschijnt. ! Bij handmatig afstemmen is de afstemstap vast ingesteld op 50 kHz. ! Als de functies AF en TA zijn uitgeschakeld, is de afstemstap vast ingesteld op 50 kHz, ook als 100 is geselecteerd. 5 Draai aan M.C. en selecteer YES om de instelling te voltooien. # Als u nog iets wilt wijzigen, draait u M.C. naar NO. 6 Druk op M.C. om uw keuze te bevestigen. Opmerkingen ! U kunt de menu-opties instellen in het systeemmenu en het begininstellingenmenu. Raadpleeg Systeemmenu op bladzijde 95 en Beginmenu op bladzijde 95 voor meer informatie over de instellingen. ! U kunt het instellingenmenu annuleren door op SRC/OFF te drukken. Nederlands c (lijst) (iPod-bediening) De iPod-functie van dit toestel wordt via de iPod bediend. a b cd tot 6/ b Draai aan M.C. en selecteer YES. # Als u het toestel niet binnen 30 seconden gebruikt, wordt het instellingenmenu niet weergegeven. # Als u de instelling later wilt maken, selecteert u met M.C. nu NO. 02 Basisbediening Het toestel inschakelen 1 Druk op SRC/OFF om het toestel in te schakelen. Het toestel uitschakelen 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. 1 Zet het contact aan na de installatie van dit toestel. SET UP verschijnt. Nl <QRD3247-B> 89 89 Black plate (90,1) Hoofdstuk Gebruik van het toestel 02 Een signaalbron selecteren 1 Druk op SRC/OFF om over te schakelen tussen: RADIO—CD—USB/iPod—APP (toepassing)— AUX ! Wanneer de MTP-verbinding actief is, wordt USB MTP weergegeven. ! Als een iPod aangesloten is en een andere bron dan iPod geselecteerd is, kunt u naar iPod overschakelen door op iPod te drukken. Het volume afstellen 1 Draai aan M.C. om het volume te regelen. Opmerking Als de blauw-witte draad van dit toestel is aangesloten op de bedieningsaansluiting van de automatische antenne van het voertuig, schuift de antenne uit wanneer er een signaalbron van dit toestel wordt ingeschakeld. Als de signaalbron wordt uitgeschakeld, wordt de antenne weer ingeschoven. Veelgebruikte menufuncties Terugkeren naar het vorige display Terugkeren naar de vorige lijst (de map die een niveau hoger ligt) 1 Druk op /DIMMER. Terugkeren naar het gewone display Het hoofdmenu annuleren 1 Druk op BAND/ . Terugkeren naar het gewone display van de lijst 1 Druk op BAND/ . Gebruik van het toestel Radio Basisbediening Een frequentieband selecteren 1 Druk op BAND/ totdat de gewenste frequentieband (FM1, FM2, FM3 voor FM of MW/LW) op het display verschijnt. Overschakelen tussen voorkeuzestations 1 Druk op c of d. ! Om deze functie te gebruiken, moet u PCH (voorkeuzezender) selecteren onder SEEK. Handmatig afstemmen (stap voor stap) 1 Druk op c of d. ! Om deze functie te gebruiken, moet u MAN (handmatig afstemmen) selecteren onder SEEK. Automatisch afstemmen 1 Houd c of d ingedrukt en laat deze weer los. U kunt het automatisch afstemmen afbreken door even op c of d te drukken. Als u c of d ingedrukt houdt, worden zenders overgeslagen. Het automatisch afstemmen begint zodra u c of d loslaat. Opmerkingen ! Raadpleeg SEEK (instelling linker/rechter toets) op bladzijde 91 voor meer informatie over SEEK. ! U kunt de AF-functie (zoeken naar alternatieve frequenties) in- en uitschakelen. Voor normaal afstemmen moet de AF-functie uit staan (raadpleeg AF (alternatieve frequenties zoeken) op bladzijde 91). Zenders voor de verschillende frequentiebanden opslaan en oproepen De voorkeuzetoetsen gebruiken 1 Opslaan: Houd de gewenste voorkeuzetoets (1/ t/m 6/ ) ingedrukt tot het nummer stopt met knipperen. 2 Oproepen: Druk op de gewenste voorkeuzetoets (1/ t/m 6/ ). Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! FREQUENCY (programmaservicenaam of frequentie) ! BRDCST INFO (programmaservicenaam/ PTY-informatie) ! CLOCK (naam signaalbron en klok) Opmerkingen ! Als de programmaservicenaam niet gedetecteerd kan worden in FREQUENCY, wordt de frequentie weergegeven. Anders wordt de programmaservicenaam weergegeven. ! Afhankelijk van de frequentieband kan de tekstinformatie verschillen. ! Welke tekstinformatie gewijzigd kan worden, hangt af van het gebied. RDS-zenders zoeken via PTY-informatie (lijst). 1 Druk op 2 Draai aan M.C. om een programmatype te kiezen. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Druk op M.C. om het zoeken te beginnen. Het toestel zoekt naar een zender die het geselecteerde programmatype uitzendt. Als er een zender is gevonden, wordt de programmaservicenaam weergegeven. ! Druk opnieuw op M.C. om het zoeken te annuleren. ! Het programma van een zender kan afwijken van de informatie die door de PTY-code wordt aangegeven. ! Als er geen zender gevonden wordt die het gewenste soort programma uitzendt, wordt op het display ongeveer twee seconden lang NOT FOUND getoond en keert de tuner terug naar de oorspronkelijke zender. PTY-lijst Bezoek de volgende website voor meer informatie over de PTY-lijst: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Functie-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. PTY-functies Met behulp van PTY-informatie (programmatypeinformatie) kunt u op een bepaald soort zender afstemmen. 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. 3 Draai aan M.C. om de gewenste functie te selecteren. U kunt de volgende functies aanpassen. # Als de MW/LW-band is geselecteerd, zijn alleen BSM, LOCAL en SEEK beschikbaar. 90 Nl <QRD3247-B> 90 Black plate (91,1) Hoofdstuk Gebruik van het toestel FM SETTING (instellingen voor FM-geluidskwaliteit) De geluidskwaliteit kan worden aangepast aan het signaal van de FM-band. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. ! STANDARD – Dit is de standaardinstelling. ! HI-FI – In deze instelling wordt de hoge kwaliteit van stereogeluid benadrukt. ! STABLE – In deze instelling wordt de lage ruis van monogeluid benadrukt. BSM (geheugen voor de sterkste zenders) Met de functie BSM (Best Stations Memory) kunt u automatisch de zes sterkste zenders in het geheugen opslaan. Deze worden opgeslagen in volgorde van signaalsterkte. 1 Druk op M.C. om de functie BSM in te schakelen. Druk nogmaals op M.C. om deze te annuleren. REGIONAL (regionaal) Als de functie AF is ingeschakeld, kan de regionale functie gebruikt worden om het zoeken tot regionale programma’s te beperken. 1 Druk op M.C. om de regionale functie in of uit te schakelen. Als deze functie is ingeschakeld, stemt het toestel alleen af op zenders waarvan het signaal voldoende sterk is voor een goede ontvangst. 1 Druk op M.C. en selecteer de gewenste instelling. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Als u het hoogste niveau selecteert, wordt alleen afgestemd op de sterkste zenders. Bij lagere niveaus wordt ook afgestemd op zwakkere zenders. TA (stand-by voor verkeersberichten) 1 Druk op M.C. om de functie Stand-by voor verkeersberichten in en uit te schakelen. AF (alternatieve frequenties zoeken) 1 Druk op M.C. om AF aan of uit te zetten. NEWS (onderbreking door nieuwsberichten) 1 Druk op M.C. om de nieuwsfunctie in of uit te schakelen. SEEK (instelling linker/rechter toets) U kunt een functie toewijzen aan de linker en rechter toets van het toestel. Selecteer MAN (handmatig afstemmen) om handmatig af te stemmen of PCH (voorkeuzezenders) om op voorkeuzezenders af te stemmen. 1 Druk op M.C. om MAN of PCH te selecteren. Cd/cd-r/cd-rw-discs en USBopslagapparaten MTP-verbinding Android-apparaten die compatibel zijn met MTP (apparaten met Android OS 4.0 of hoger) kunnen via de USB-bron met een MTP-verbinding worden aangesloten. Sluit Android-apparaten aan met de eigen kabel van het apparaat. Opmerking Deze functie is niet compatibel met WAV. Basisbediening Een cd/cd-r/cd-rw afspelen 1 Plaats een disc met het etiket omhoog in de laadsleuf. Songs op een USB-opslagapparaat afspelen 1 Open het deksel van de USB-poort. 2 Sluit het USB-opslagapparaat aan via een USB-kabel. Stoppen met afspelen van songs op een USB-opslagapparaat 1 U kunt een USB-opslagapparaat op elk gewenst moment verwijderen. Een map selecteren 1 Druk op 1/ of 2/ . Een fragment selecteren 1 Druk op c of d. Vooruit of achteruit spoelen 1 Houd c of d ingedrukt. ! Als u gecomprimeerde audio afspeelt, is er geen geluid bij vooruit- en achteruitspoelen. Terugkeren naar de hoofdmap 1 Houd BAND/ ingedrukt. Overschakelen tussen gecomprimeerde audio en cd-da 1 Druk op BAND/ . Overschakelen tussen afspeelbare geheugenapparaten Als een USB-opslagapparaat meerdere USB Mass Storage-compatibele afspeelbare geheugenapparaten bevat, kunt u tussen deze apparaten overschakelen. 1 Druk op BAND/ . ! U kunt overschakelen tussen maximaal 32 verschillende geheugenapparaten. Opmerking Ontkoppel USB-opslagapparaten van dit toestel wanneer u ze niet gebruikt. 02 Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: CD-DA ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) CD-TEXT ! TRACK INFO (fragmenttitel/naam artiest fragment/disctitel) ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) MP3/WMA/WAV ! TRACK INFO (fragmenttitel/naam artiest/ albumtitel) ! FILE INFO (bestandsnaam/mapnaam) ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) Bestanden en fragmenten in de lijst selecteren en afspelen 1 Druk op om over te schakelen naar de lijst met bestands- of fragmentnamen. 2 Gebruik M.C. om de gewenste bestandsnaam (of mapnaam) te selecteren. Een bestand of map selecteren 1 Draai aan M.C. Nederlands LOCAL (automatisch afstemmen op lokale zenders) Gebruik van het toestel Afspelen 1 Selecteer een bestand of fragment en druk op M.C. Een cd/cd-r/cd-rw uitwerpen 1 Druk op h. Nl <QRD3247-B> 91 91 Black plate (92,1) Hoofdstuk Gebruik van het toestel 02 Een lijst van de bestanden (mappen) in de geselecteerde map weergeven 1 Selecteer een map en druk op M.C. Een song in de geselecteerde map afspelen 1 Selecteer een map en houd M.C. ingedrukt. Gebruik van het toestel Functie-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. U kunt de volgende functie aanpassen. Bediening met speciale toetsen S.RTRV (sound retriever) Een herhaalbereik selecteren om over te schakelen tussen: 1 Druk op 6/ Cd/cd-r/cd-rw-discs ! ALL – Alle fragmenten herhalen ! ONE – Het huidige fragment herhalen ! FLD – De huidige map herhalen USB-opslagapparaat ! ALL – Alle bestanden herhalen ! ONE – Het huidige bestand herhalen ! FLD – De huidige map herhalen Fragmenten in willekeurige volgorde afspelen om willekeurige weergave in of 1 Druk op 5/ uit te schakelen. Fragmenten in een geselecteerd herhaalbereik worden in willekeurige volgorde afgespeeld. ! Druk tijdens weergave in willekeurige volgorde op d om naar het volgende fragment te gaan. Als u op c drukt, wordt het huidige fragment opnieuw vanaf het begin afgespeeld. Het afspelen onderbreken 1 Druk op 4/PAUSE om het afspelen te onderbreken (pauze) of te hervatten. De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) 1 Druk op 3/S.Rtrv om over te schakelen tussen: 1—2—OFF (uit) 1 heeft effect bij lage compressie en 2 heeft effect bij hoge compressie. 92 Deze verbetert automatisch de weergave van gecomprimeerde audio en zorgt voor een vol geluid. 1 Druk op M.C. en selecteer de gewenste instelling. Raadpleeg De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) op bladzijde 92 voor meer informatie. ! De iPod wordt uitgeschakeld ongeveer twee minuten nadat de contactschakelaar is uitgezet. Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! TRACK INFO (fragmenttitel/naam artiest/ albumtitel) ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) Naar een song bladeren 1 Druk op om naar het hoofdmenu met zoeklijsten te gaan. iPod 2 Selecteer een categorie of song met M.C. Basisbediening Muziek op een iPod afspelen 1 Open het deksel van de USB-poort. 2 Sluit een iPod aan op de USB-ingang. Het afspelen begint automatisch. De naam van een song of categorie wijzigen 1 Draai aan M.C. Speellijsten—artiesten—albums—songs— podcasts—genres—componisten—audioboeken Een song selecteren (hoofdstuk) 1 Druk op c of d. Afspelen 1 Selecteer een song en druk op M.C. Een album selecteren 1 Druk op 1/ of 2/ . Een lijst van songs in de geselecteerde categorie weergeven 1 Selecteer een categorie en druk op M.C. Vooruit of achteruit spoelen 1 Houd c of d ingedrukt. Opmerkingen ! De iPod kan niet worden in- en uitgeschakeld als de bedieningsmodus is ingesteld op CTRL AUDIO. ! Verwijder de koptelefoon van de iPod voordat u hem op dit toestel aansluit. Een song in de geselecteerde categorie afspelen 1 Selecteer een categorie en houd M.C. ingedrukt. Alfabetisch in een lijst zoeken 1 Geef de lijst voor de geselecteerde categorie om alfabetisch te zoeken. weer en druk op ! U kunt ook overschakelen naar alfabetisch zoeken door twee keer aan M.C. te draaien. 2 Draai aan M.C. om een letter te selecteren. 3 Druk op M.C. om de alfabetische lijst weer te geven. ! Druk op /DIMMER om het zoeken te annuleren. Opmerkingen ! U kunt speellijsten afspelen die zijn gemaakt met de computertoepassing MusicSphere. Deze toepassing is beschikbaar op onze website. ! Speellijsten die zijn gemaakt met de computertoepassing MusicSphere worden verkort weergegeven. Bediening met speciale toetsen Een herhaalbereik selecteren om over te schakelen tussen: 1 Druk op 6/ ! ONE – De huidige song herhalen ! ALL – Alle songs in de geselecteerde lijst herhalen ! In de bedieningsmodus CTRL iPod wordt hetzelfde herhaalbereik gebruikt dat is ingesteld voor de aangesloten iPod. Een herhaalbereik voor afspelen in willekeurige volgorde (shuffle) selecteren om over te schakelen tussen: 1 Druk op 5/ ! SNG – De songs in de geselecteerde lijst in willekeurige volgorde afspelen. ! ALB – De songs van een willekeurig album op volgorde afspelen. ! OFF – Niet afspelen in willekeurige volgorde. Nl <QRD3247-B> 92 Black plate (93,1) Hoofdstuk Gebruik van het toestel Alle songs in willekeurige volgorde afspelen (shuffle all) ingedrukt om de functie Shuffle 1 Houd 5/ all in te schakelen. ! Selecteer OFF in Shuffle om Shuffle all uit te schakelen. Raadpleeg voor meer informatie Een herhaalbereik voor afspelen in willekeurige volgorde (shuffle) selecteren op bladzijde 92. Het afspelen onderbreken 1 Druk op 4/PAUSE om het afspelen te onderbreken (pauze) of te hervatten. De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) 1 Druk op 3/S.Rtrv om over te schakelen tussen: 1—2—OFF (uit) 1 heeft effect bij lage compressie en 2 heeft effect bij hoge compressie. Songs afspelen die verwant zijn met de huidige song De volgende lijsten voor songs zijn beschikbaar. • Lijst van albums van de huidige artiest • Lijst van songs op het huidige album • Lijst van albums van het huidige genre 1 Houd ingedrukt om naar de gekoppelde weergavemodus over te schakelen. ! ARTIST – Een album van de huidige artiest afspelen. ! ALBUM – Een song van het huidige album afspelen. ! GENRE – Een album van het huidige genre afspelen. De geselecteerde song of het geselecteerde album wordt na de huidige song afgespeeld. Opmerkingen ! De geselecteerde song of het geselecteerde album kan worden geannuleerd als u een andere functie dan gekoppeld zoeken gebruikt (bijvoorbeeld snel vooruit of achteruit spoelen). ! Afhankelijk van de geselecteerde song is het mogelijk dat het einde van de huidige song en het begin van de geselecteerde song (album) worden afgesneden. De iPod-functie van dit toestel via de iPod gebruiken De iPod-functie van dit toestel kan via een aangesloten iPod bediend worden. CTRL iPod kan niet worden gebruikt met de volgende iPod-modellen. ! iPod nano 1e generatie ! iPod met video % Druk op BAND/ dus te wijzigen. om de bedieningsmo- ! CTRL iPod – De iPod-functie van dit toestel kan via de aangesloten iPod bediend worden. ! CTRL AUDIO – De iPod-functie van dit toestel kan via dit toestel bediend worden. U kunt ook op iPod drukken om de bedieningsmodus te wijzigen. Opmerkingen ! Als u de bedieningsmodus overschakelt op CTRL iPod, wordt het afspelen van songs onderbroken. Gebruik de iPod om de weergave te hervatten. ! Ook als de bedieningsmodus is ingesteld op CTRL iPod, kunnen de volgende functies vanaf dit toestel bediend worden. — Pauze — Vooruit en achteruit spoelen — Een song selecteren (hoofdstuk) ! Het volume kan alleen vanaf dit toestel worden bijgesteld. Functie-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. 3 Draai aan M.C. om de gewenste functie te selecteren. U kunt de volgende functies aanpassen. ! AUDIO BOOK kan niet worden gebruikt als CTRL iPod is geselecteerd in de bedieningsmodus. Raadpleeg De iPod-functie van dit toestel via de iPod gebruiken op bladzijde 93 voor meer informatie. AUDIO BOOK (audioboeksnelheid) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. ! FASTER – Weergave is sneller dan normaal ! NORMAL – Weergave met normale snelheid ! SLOWER – Weergave is langzamer dan normaal S.RTRV (sound retriever) 1 Druk op M.C. en selecteer de gewenste instelling. Raadpleeg De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) op bladzijde 93 voor meer informatie. Applicaties van aangesloten apparaten gebruiken Via dit toestel kunt u songs van iPhone-applicaties via streaming afspelen en bedienen of alleen via streaming afspelen. 02 Belangrijk Voor gebruik van applicaties van derden worden mogelijk persoonsgegevens gebruikt of moet u zulke gegevens verstrekken, bijvoorbeeld door het opzetten van een gebruikersaccount of op andere wijze, en voor sommige applicaties worden mogelijk geolocatiegegevens gebruikt. ALLE APPLICATIES VAN DERDEN VALLEN UITSLUITEND ONDER VERANTWOORDELIJKHEID VAN HUN UITGEVER, INCLUSIEF MAAR NIET BEPERKT TOT HET VERZAMELEN EN BEVEILIGEN VAN GEBRUIKERSGEGEVENS EN HET PRIVACYBELEID. DOOR EEN APPLICATIE VAN DERDEN TE GEBRUIKEN, GAAT U ERMEE AKKOORD OM U TE INFORMEREN OVER DE GEBRUIKSVOORWAARDEN EN HET PRIVACYBELEID VAN DE UITGEVER ERVAN. ALS U NIET AKKOORD GAAT MET DE GEBRUIKSVOORWAARDEN OF HET BELEID VAN EEN UITGEVER OF GEEN TOESTEMMING GEEFT VOOR HET GEBRUIK VAN GEOLOCATIEGEGEVENS (INDIEN VAN TOEPASSING), MOET U DE APPLICATIE NIET GEBRUIKEN. Informatie over de compatibiliteit van aangesloten apparaten Hieronder vindt u gedetailleerde informatie over de benodigde aansluitingen om de applicatie voor iPhone op dit toestel te gebruiken. Voor iPhone ! Deze functie is compatibel met de iPhone en iPod touch. ! Het apparaat moet iOS 5.0 of later hebben. Nederlands 2 Draai aan M.C. om een andere modus te kiezen; druk erop om een modus te selecteren. Gebruik van het toestel Opmerkingen ! Raadpleeg onze website voor een overzicht van ondersteunde iPhone-applicaties voor dit toestel. Nl <QRD3247-B> 93 93 Black plate (94,1) Hoofdstuk Gebruik van het toestel 02 ! Pioneer is niet aansprakelijk voor problemen die kunnen ontstaan door fouten of gebreken in de gebruikte toepassing. ! De provider van de App is verantwoordelijk voor de inhoud en de functionaliteit van de aangeboden toepassing. Gebruik van het toestel 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. 3 Draai aan M.C. om de gewenste functie te selecteren. U kunt de volgende functies aanpassen. Startprocedure voor iPhone PAUSE (pauze) FADER (fader aanpassen) 1 Sluit een iPhone aan op de USB-ingang. 2 Schakel de signaalbron over naar APP. 1 Druk op M.C. om het afspelen te onderbreken (pauze) of te hervatten. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de balans tussen de luidsprekers voorin en achterin in te stellen. S.RTRV (sound retriever) 3 Start de applicatie op de iPhone en begin met afspelen. Basisbediening Een fragment selecteren 1 Druk op c of d. Vooruit of achteruit spoelen 1 Houd c of d ingedrukt. Het afspelen onderbreken 1 Druk op BAND/ om het afspelen te onderbreken (pauze) of te hervatten. Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! TRACK INFO (fragmenttitel/naam artiest/ albumtitel) ! APP NAME (naam van applicatie) ! ELAPSED TIME (weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) Functie-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 94 ! SUB.W CTRL kan niet worden gebruikt als SUB.W is geselecteerd in OFF. Raadpleeg voor meer informatie SUB.W (subwoofer aan/ uit) op bladzijde 94. ! SLA is niet beschikbaar als de signaalbron is ingesteld op FM. 1 Druk op M.C. en selecteer de gewenste instelling. 1—2—OFF (uit) 1 heeft effect bij lage compressie en 2 heeft effect bij hoge compressie. Audio-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie AUDIO en druk erop. 3 Draai aan M.C. en selecteer de audiofunctie. U kunt de volgende audiofuncties aanpassen. ! FADER kan niet worden gebruikt als SUB.W/SUB.W is geselecteerd in SP-P/O MODE. Raadpleeg voor meer informatie SP-P/O MODE (achteruitgang en preout-instelling) op bladzijde 96. ! SUB.W en SUB.W CTRL kunnen niet worden gebruikt als REAR/REAR is geselecteerd in SP-P/O MODE. Raadpleeg voor meer informatie SP-P/O MODE (achteruitgang en preout-instelling) op bladzijde 96. BALANCE (balansinstelling) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de balans tussen de linker/ rechterluidsprekers in te stellen. EQ SETTING (equalizercurven) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de equalizer te selecteren. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS De equalizerband en het equalizerniveau kunnen worden aangepast van CUSTOM1 en CUSTOM2. Volg de onderstaande procedure als u CUSTOM1 of CUSTOM2 selecteert. Voor een andere optie drukt u op M.C. om terug te keren naar het vorige display. ! CUSTOM1 kan voor elke signaalbron afzonderlijk worden ingesteld. USB, iPod en APP worden echter automatisch op dezelfde stand ingesteld. ! CUSTOM2 is een gemeenschappelijk instelling voor alle signaalbronnen. 3 Druk op M.C. om de instellingenmodus weer te geven. 4 Druk op M.C. om over te schakelen tussen: Equalizerband—Equalizerniveau 5 Draai aan M.C. en selecteer de gewenste instelling. Equalizerband: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizerniveau: +6 tot –6 LOUDNESS (loudness) De loudness-functie compenseert een tekort aan lage tonen en hoge tonen bij een laag volume. 1 Druk op M.C. en selecteer de gewenste instelling. OFF (uit)—LOW (laag)—MID (midden)—HI (hoog) SUB.W (subwoofer aan/uit) Dit toestel is voorzien van een in- en uitschakelbare subwooferuitgang. 1 Druk op M.C. en selecteer de gewenste instelling. NOR (normale fase)—REV (tegengestelde fase)—OFF (subwoofer uit) Nl <QRD3247-B> 94 Black plate (95,1) Hoofdstuk Gebruik van het toestel Gebruik van het toestel SUB.W CTRL (subwoofer aanpassen) SLA (bronniveauregeling) CLOCK SET (klok) De subwoofer geeft alleen frequenties beneden de geselecteerde waarde weer. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om over te schakelen tussen: Drempelfrequentie—Uitgangsniveau—Vervalniveau Instelbare waarden knipperen. 3 Draai aan M.C. en selecteer de gewenste instelling. Drempelfrequentie: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Uitgangsniveau: –24 tot +6 Hellingsniveau: –12 — –24 De functie voorkomt sterke volumewisselingen wanneer de bron wordt overgeschakeld. ! De instellingen zijn gebaseerd op het FM-volumeniveau, dat zelf niet gewijzigd kan worden. ! Het MW/LW-volumeniveau kan ook met deze functie worden aangepast. ! USB, iPod en APP worden automatisch hetzelfde ingesteld. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om het bronvolume te regelen. Instelbereik: +4 tot –4 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om het onderdeel van de klok te selecteren dat u wilt instellen. Uur—Minuut 3 Draai aan M.C. om de klok in te stellen. BASS BOOST (bass boost) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer het gewenste niveau. U kunt het niveau verhogen of verlagen tussen de waarden 0 en +6. De waarde wordt op het display getoond. HPF SETTING (high pass filter aanpassen) 1 Druk op M.C. en selecteer de gewenste instelling. 12H (12-uurs klok)—24H (24-uurs klok) AUTO PI (automatisch PI-zoeken) Systeemmenu Belangrijk Als het toestel van de accu wordt losgekoppeld, wordt PW SAVE (energiezuinige modus) uitgeschakeld. Deze functie moet u weer inschakelen als het toestel terug met de accu wordt verbonden. Als het voertuig niet van een contactschakelaar met accessoirestand (ACC) is voorzien, is het (afhankelijk van de aansluiting) mogelijk dat het toestel de accu blijft belasten als PW SAVE (energiezuinige modus) is uitgeschakeld. 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. 3 Draai aan M.C. en selecteer de systeemmenufunctie. U kunt de volgende functies in het systeemmenu aanpassen. Als deze functie is ingeschakeld, probeert het toestel bij slechte ontvangst automatisch een andere zender met gelijkaardige programma’s te vinden, ook als u een voorkeuzezender selecteerde. 1 Druk op M.C. om de automatische PI-zoekfunctie in of uit te schakelen. Het geluid van dit toestel kan automatisch worden uitgeschakeld of gedempt wanneer een ander apparaat met uitschakelingsfunctie daarom vraagt met een speciaal signaal. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. ! MUTE – Tijdelijk uitschakelen ! 20dB ATT – Dempen (20dB ATT heeft meer effect dan 10dB ATT) ! 10dB ATT – Dempen PW SAVE (energiezuinige stand) Met deze functie wordt het energieverbruik van de accu verminderd. ! Als deze functie is ingeschakeld, kan alleen het bronsignaal worden ingeschakeld. 1 Druk op M.C. om de energiezuinige modus in of uit te schakelen. AUX (externe aansluiting) Beginmenu Schakel deze instelling in als een extern apparaat op dit toestel is aangesloten. 1 Druk op M.C. om AUX in of uit te schakelen. 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. DIMMER (dimmer) 2 Houd SRC/OFF ingedrukt tot het hoofdmenu wordt weergegeven. 1 Druk op M.C. om de dimmer in of uit te schakelen. ! U kunt de dimmer ook instellen door /DIMMER even ingedrukt te houden. 3 Draai aan M.C., selecteer de menuoptie INITIAL en druk erop. MUTE MODE (dempen) 4 Draai aan M.C. en selecteer de gewenste functie. U kunt de volgende functies in het beginmenu aanpassen. Nederlands Gebruik deze functie als u alleen naar geluid met hogere frequenties wilt luisteren. Alleen frequenties boven de drempelfrequentie van het high pass filter worden weergegeven. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om over te schakelen tussen: Drempelfrequentie—Vervalniveau 3 Draai aan M.C. en selecteer de gewenste instelling. Drempelfrequentie: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Hellingsniveau: –12 — –24 12H/24H (tijdweergave) 02 FM STEP (FM-afstemstap) LANGUAGE (taalinstelling) 1 Druk op M.C. en selecteer de gewenste instelling. ENG (Engels)—РУС (Russisch)—TUR (Turks) 1 Druk op M.C. om de FM-afstemstap te selecteren. 100 (100 kHz)—50 (50 kHz) Nl <QRD3247-B> 95 95 Black plate (96,1) Hoofdstuk Gebruik van het toestel 02 Installatie 03 De AUX-signaalbron 1 Steek de stereo-miniplugkabel in de AUX-ingang van dit toestel. 2 Houd SRC/OFF ingedrukt tot het hoofdmenu wordt weergegeven. 3 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. Opmerking De signaalbron AUX kan alleen worden geselecteerd als de externe aansluiting is ingeschakeld. Raadpleeg voor meer informatie AUX (externe aansluiting) op bladzijde 95. Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! Naam signaalbron ! Naam signaalbron en klok Als een scherm verkeerd wordt weergegeven 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. 3 Draai aan M.C., geef DEMO OFF weer en druk erop. 4 Draai aan M.C. en selecteer YES. 5 Druk op M.C. om uw keuze te bevestigen. 96 OF F O ACC-stand STAR 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. Belangrijk ! Als dit toestel wordt geïnstalleerd in een voertuig met een contactschakelaar zonder ACCstand (accessoirestand), kan de accu leeglopen als de rode kabel niet wordt aangesloten op de aansluiting die de bediening van de contactschakelaar herkent. 2 Druk op SRC/OFF en kies AUX als signaalbron. Zet het ongewenste scherm als volgt uit. Systeemmenu Verbindingen N Op de uitgang voor de achterluidspreker en de RCA-uitgang van dit toestel kan een luidspreker met volledig bereik of een subwoofer aangesloten worden. Selecteer de gewenste instelling. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. ! REAR/SUB.W – Selecteer deze stand als op de uitgang voor de achterluidspreker een luidspreker met volledig bereik aangesloten is, en op de RCA-uitgang een subwoofer aangesloten is. ! SUB.W/SUB.W – Selecteer deze stand als op de uitgang voor de achterluidspreker een subwoofer rechtstreeks aangesloten is zonder versterker, en op de RCA-uitgang een subwoofer is aangesloten. ! REAR/REAR – Selecteer deze stand als op de uitgang voor de achterluidspreker en op de RCA-uitgang een luidspreker met volledig bereik is aangesloten. Als op de uitgang voor de achterluidspreker een luidspreker met volledig bereik is aangesloten en de RCA-uitgang niet gebruikt wordt, kunt u zowel REAR/SUB.W als REAR/REAR selecteren. 4 Draai aan M.C. en selecteer de systeemmenufunctie. Raadpleeg Systeemmenu op bladzijde 95 voor meer informatie. T SP-P/O MODE (achteruitgang en preout-instelling) Geen ACC-stand ! Gebruik van dit toestel onder andere omstandigheden dan de volgende kan leiden tot brand of storingen. — Voertuigen met een accu van 12 volt en negatieve aarding. — Luidsprekers van 50 W (uitgangswaarde) en 4 W tot 8 W (impedantiewaarde). ! Om kortsluiting, oververhitting en storingen te voorkomen, moet u onderstaande aanwijzingen opvolgen. — Koppel de negatieve aansluiting van de accu los voordat u het toestel installeert. — Gebruik kabelklemmen of plakband om de bekabeling veilig aan te brengen. Bescherm de kabels met plakband op plaatsen waar deze tegen metalen onderdelen liggen. — Plaats geen kabels in de buurt van beweegbare onderdelen zoals de versnellingspook of de stoelrails. — Leg kabels niet op plaatsen die heet kunnen worden, zoals dicht bij de kachel. — Sluit de gele kabel niet op de accu aan via een gat in het motorcompartiment. — Dek alle ongebruikte kabelaansluitingen af met isolatietape. — Maak de kabels niet korter. — Verwijder nooit de isolatie van de voedingskabel van dit toestel om andere apparaten van stroom te voorzien. De stroomcapaciteit van de voedingskabel is beperkt. — Gebruik een zekering met het voorgeschreven vermogen. — Verbind de negatieve luidsprekerkabel nooit rechtstreeks met de aarding. — Voeg de negatieve kabels van verschillende luidsprekers nooit samen. ! Als dit apparaat aan staat, wordt het bedieningssignaal doorgegeven via de blauw/witte kabel. Verbind deze kabel met de afstandsbediening van een externe versterker of met de bedieningsaansluiting van de automatische antenne van het voertuig (maximaal 300 mA, 12 V gelijkstroom). Als het voertuig is uitgerust met een glasantenne, verbindt u deze met de voedingsaansluiting van de antennebooster. ! Verbind de blauw/witte kabel nooit met de voedingsaansluiting van een externe versterker of automatische antenne. Anders kan de accu leeglopen of kan er storing optreden. ! De zwarte kabel is de aarding. Dit toestel moet gescheiden worden geaard van andere apparaten (met name apparaten die veel stroom verbruiken zoals een versterker). Anders kan er brand of storing ontstaan wanneer de aarding per ongeluk losraakt. Dit toestel 1 23 4 5 1 Antenne-ingang 2 Zekering (10 A) 3 Ingang stroomkabel Nl <QRD3247-B> 96 Black plate (97,1) Hoofdstuk Installatie Installatie 4 Ingang voor draadafstandsbediening Een bedrade afstandsbedieningsadapter kan aangesloten worden (los verkrijgbaar). 5 Achteruitgang of subwooferuitgang Stroomkabel 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d Opmerkingen ! Wijzig het beginmenu van het toestel. Raadpleeg gedeelte SP-P/O MODE (achteruitgang en preout-instelling) op bladzijde 96. De subwooferuitgang van dit toestel is mono. ! Als u een subwoofer van 70 W (2 W) gebruikt, moet u de subwoofer aansluiten op de violette en zwart-violette draden van dit toestel. Sluit niets aan op de groene en groen-zwarte draden. Versterker (apart verkrijgbaar) Maak deze verbindingen als de optionele versterker wordt gebruikt. 60° 3 1 5 ! Dit toestel werkt het beste als het wordt geplaatst onder een hoek van minder dan 60°. 2     4 5 1 Systeemafstandsbediening Verbinden met blauw-witte kabel. 2 Versterker (apart verkrijgbaar) 3 Aansluiten op RCA-kabels (apart verkrijgbaar) 4 Naar achteruitgang of subwooferuitgang 5 Luidspreker achterin of subwoofer ! Laat bij het plaatsen voldoende ruimte vrij achter het achterpaneel en wikkel losse kabels zo dat ze de ventilatiegaten niet blokkeren; zorg altijd dat warmte goed wordt afgevoerd tijdens gebruik van het toestel. Laat voldoende 5 cm ruimte vrij Installatie ! ! ! ! Belangrijk Controleer alle aansluitingen en systemen voordat u de installatie voltooit. Gebruik geen onderdelen van andere fabrikanten; deze kunnen storingen veroorzaken. Neem contact op met uw dealer als er voor de installatie gaten moeten worden geboord of als er andere aanpassingen aan het voertuig nodig zijn. Installeer dit toestel niet op een plaats waar: — het de besturing van het voertuig kan belemmeren. — het de inzittenden kan verwonden bij een noodstop. 5 cm 5cm cm ! Gebruik voor installatie in de handel verkrijgbare onderdelen. Installatie Het toestel kan op een van de volgende wijzen geïnstalleerd worden. ! Installatie met de houder ! Monteren met de schroefgaten aan de zijkant van het toestel Nederlands 1 Naar ingang stroomkabel 2 De functie van 3 en 5 kan verschillen afhankelijk van het type voertuig. Verbind in dat geval 4 met 5 en 6 met 3. 3 Geel Back-up (of accessoire) 4 Geel Aansluiten op de constante 12 V-voedingsaansluiting. 5 Rood Accessoire (of back-up) 6 Rood Aansluiten op een aansluiting die door de contactschakelaar wordt aangestuurd (12 V gelijkstroom). 7 Verbind kabels van dezelfde kleur met elkaar. 8 Zwart (chassisaarding) 9 Blauw-wit De pinpositie van de ISO-connector verschilt naargelang het type voertuig. Als pin 5 de antenne aanstuurt, verbindt u 9 en b. In andere typen voertuigen verbindt u 9 en b nooit. a Blauw-wit Aansluiten op systeembedieningsaansluiting van de versterker (maximaal 300 mA, 12 V gelijkstroom). b Blauw-wit Aansluiten op bedieningsaansluiting van de gemotoriseerde antenne (maximaal 300 mA, 12 V gelijkstroom). c Geel/zwart Als u apparatuur met dempingsfunctie gebruikt, verbindt u deze draad met de draad voor audiodemping op die apparatuur. Als u zulke apparatuur niet gebruikt, verbindt u de draad voor audiodemping niet. d Luidsprekerkabels Wit: Linksvoor + Wit-zwart: Linksvoor * Grijs: Rechtsvoor + Grijs-zwart: Rechtsvoor * Groen: Linksachter + of subwoofer + Groen-zwart: Linksachter * of subwoofer * Violet: Rechtsachter + of subwoofer + Violet-zwart: Rechtsachter * of subwoofer * e ISO-connector Bij sommige voertuigen is de ISO-connector in twee verdeeld. Verbind in dat geval beide connectoren. 03 ! De halfgeleiderlaser raakt bij oververhitting beschadigd. Plaats dit apparaat niet op plaatsen waar het warm wordt, zoals nabij de uitlaat van een kachel. Nl <QRD3247-B> 97 97 Black plate (98,1) Hoofdstuk Installatie 03 Installatie 1 Houder (meegeleverd onderdeel) Voordat u het toestel monteert 1 3 Bevestig de sierlijst. 1 2 Verwijder de sierlijst. Installatie met de houder 1 Monteer de houder in het dashboard. Nadat u de houder in het dashboard geplaatst hebt, kiest en buigt u lipjes die geschikt zijn voor de dikte van het dashboardmateriaal. (Monteer dit toestel zo stevig mogelijk met behulp van de boven- en onderlipjes. Om het toestel vast te zetten, buigt u de lipjes 90 graden.) 3 1 1 1 1 Sierlijst 1 Sierlijst De houder verwijderen 2 Steek de meegeleverde uittreksleutels in de beide kanten van het toestel totdat ze op hun plaats klikken. 2 1 Dashboard 2 Houder (meegeleverd onderdeel) 2 Installeer het toestel. 3 Trek het toestel uit de houder. Verwijder de houder. De procedure is gelijk aan die in Voordat u het toestel monteert. Raadpleeg voor meer informatie Voordat u het toestel monteert op bladzijde 98. 4 1 Als het uitsteekseltje in de weg zit, buigt u het omlaag. 2 Radiomontageklem 3 Platbolkopschroeven (5 mm × 8 mm) 4 Dashboard of console Monteren met de schroefgaten aan de zijkant van het toestel % Bevestig het toestel aan de radiomontageklem. Plaats het toestel zo dat de schroefgaten ervan samenvallen met de schroefgaten van de klem. Zet het toestel vast met drie schroeven aan elke kant. 1 1 1 Dashboard 98 Nl <QRD3247-B> 98 Black plate (99,1) Aanhangsel Aanvullende informatie Aanvullende informatie Problemen verhelpen Foutmeldingen Symptomen worden vet gedrukt. Oorzaken worden in gewoon lettertype zonder inspringen gedrukt. Gewone en ingesprongen tekst geeft aan wat u moet doen. Schrijf een foutmelding altijd nauwkeurig op en houd die bij de hand als u contact opneemt met uw leverancier of Pioneer-servicecentrum. Foutmeldingen worden vet gedrukt. Oorzaken worden in gewoon lettertype zonder inspringen gedrukt. Gewone, ingesprongen tekst geeft aan wat u moet doen. Het display keert automatisch terug naar het gewone display. U hebt gedurende ongeveer 30 seconden geen handeling uitgevoerd. Voer de handeling opnieuw uit. Het bereik voor herhaald afspelen wordt onverwachts gewijzigd. Afhankelijk van het herhaalbereik kan het geselecteerde bereik gewijzigd worden wanneer u een andere map of een ander fragment selecteert of vooruit of achteruit spoelt. Selecteer het gewenste herhaalbereik opnieuw. Algemeen AMP ERROR Dit toestel werkt niet of er is een probleem met de luidsprekeraansluiting; het beveiligingscircuit is geactiveerd. Controleer de luidsprekeraansluiting. Neem contact op met uw leverancier of een erkend Pioneer Servicecentrum als het bericht nog wordt weergegeven nadat u de motor hebt uit- en aangezet. ERROR-23 Het cd-formaat wordt niet ondersteund. Plaats een andere disc. FORMAT READ Na het begin van het afspelen duurt het soms even totdat er geluid klinkt. Wacht tot het bericht verdwijnt en er geluid klinkt. Onderliggende mappen worden niet afgespeeld wanneer FLD (map herhalen) is geselecteerd. Selecteer een ander herhaalbereik. Als het display wordt gewijzigd, verschijnt NO XXXX (bijvoorbeeld NO TITLE). Het toestel functioneert niet correct. Er is interferentie. U gebruikt mogelijk een apparaat (bijvoorbeeld een mobiele telefoon) dat hoorbare interferentie veroorzaakt. Gebruik nabij dit toestel geen elektrische apparaten die interferentie kunnen veroorzaken. ERROR-07, 11, 12, 17, 30 De disc is vuil. Reinig de disc. De disc is bekrast. Plaats een andere disc. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Elektrisch of mechanisch probleem. Zet het contact uit en weer aan, of schakel over naar een andere signaalbron en dan terug naar de cd-speler. ERROR-15 De geplaatste disc bevat geen gegevens. Plaats een andere disc. Het aangesloten USB-opslagapparaat bevat bestanden die met DRM zijn beveiligd. Beveiligde bestanden worden overgeslagen. PROTECT De geplaatste disc bevat geen afspeelbare bestanden. Plaats een andere disc. Alle bestanden op het aangesloten USB-opslagapparaat zijn beveiligd met DRM. Gebruik een ander USB-opslagapparaat. SKIPPED N/A USB De geplaatste disc bevat bestanden die door digitaal rechtenbeheer (DRM) beveiligd zijn. Beveiligde bestanden worden overgeslagen. Het aangesloten USB-apparaat wordt niet ondersteund door dit toestel. ! Gebruik een opslagapparaat dat compatibel is met USB Mass Storage Class. ! Ontkoppel het apparaat en sluit een compatibel USB-opslagapparaat aan. Alle bestanden op de disc zijn door digitaal rechtenbeheer (DRM) beveiligd. Plaats een andere disc. USB-opslagapparaat en iPod CHECK USB Er is kortsluiting opgetreden in de USB-aansluiting of de USB-kabel. Controleer of de USB-stekker en de USB-kabel niet ergens ingeklemd of beschadigd zijn. FORMAT READ Na het begin van het afspelen duurt het soms even totdat er geluid klinkt. Wacht tot het bericht verdwijnt en er geluid klinkt. NO AUDIO Er zijn geen songs. Zet de audiobestanden over naar het USBopslagapparaat en sluit het aan. CHECK USB Het aangesloten USB-opslagapparaat verbruikt meer stroom dan de maximaal toelaatbare waarde. Ontkoppel het USB-opslagapparaat en gebruik het niet meer. Zet de contactschakelaar van het voertuig uit, dan in de accessoirestand (ACC) of aan, en sluit een compatibel USBopslagapparaat aan. Nl <QRD3247-B> 99 Nederlands Er is geen tekstinformatie beschikbaar. Wijzig de displaystand of speel een ander fragment of bestand af. Cd-speler SKIPPED NO AUDIO PROTECT Een onderliggende map wordt niet afgespeeld. De inhoud van het USB-opslagapparaat is beveiligd. Raadpleeg de instructies bij het USBopslagapparaat om de beveiliging uit te schakelen. 99 Black plate (100,1) Aanhangsel Aanvullende informatie Aanvullende informatie CHECK USB NOT FOUND De iPod functioneert correct maar wordt niet opgeladen. Controleer of de kabel van de iPod niet is kortgesloten, bijvoorbeeld contact maakt met metalen voorwerpen. Zet daarna het contact uit en weer aan, of ontkoppel de iPod en sluit deze weer aan. Geen verwante songs. Zet songs over naar de iPod. ERROR-19 Communicatiefout. Probeer de volgende mogelijkheden. – Zet het contact uit en dan weer aan. – Ontkoppel het USB-opslagapparaat. – Schakel over naar een andere signaalbron. Schakel vervolgens terug naar de USBsignaalbron. iPod-fout. Verwijder de kabel uit de iPod. Sluit de kabel weer aan als het hoofdmenu van de iPod wordt weergegeven en stel de iPod opnieuw in. Applicatie START UP APP De applicatie is nog niet gestart. Volg de instructies op het scherm. Aanwijzingen voor het gebruik Discs en de player Gebruik uitsluitend discs die voorzien zijn van een van onderstaande twee logo’s. ERROR-16 De versie van de iPod-firmware is verouderd. Werk de versie van de iPod bij. iPod-fout. Verwijder de kabel uit de iPod. Sluit de kabel weer aan als het hoofdmenu van de iPod wordt weergegeven en stel de iPod opnieuw in. STOP De huidige lijst bevat geen songs. Selecteer een lijst die wel songs bevat. 100 Gebruik discs van 12 cm. Gebruik uitsluitend normale, ronde discs. De volgende typen discs kunnen niet op dit toestel worden afgespeeld: ! DualDiscs ! Discs van 8 cm: Als u deze discs met een adapter probeert af te spelen, kan het toestel defect raken. ! Discs in een ongewone vorm ! Andere discs dan cd’s ! Beschadigde discs, inclusief schijven die zijn gebarsten, gebogen of waarvan stukjes zijn afgebroken ! Cd-r/rw-discs die niet zijn gefinaliseerd USB-opslagapparaat Bewaar discs in het bijbehorende doosje wanneer u ze niet gebruikt. Het maken van verbindingen via een USB-hub wordt niet ondersteund. Plak geen labels op discs, schrijf er niet op en breng het oppervlak niet in aanraking met chemische middelen. Sluit alleen een USB-opslagapparaat aan en geen andere apparaten. Als u een cd reinigt, veegt u de disc van het midden naar de buitenkant met een zachte doek schoon. Maak het USB-opslagapparaat stevig vast voordat u gaat rijden. Zorg dat het niet op de grond valt omdat het dan onder het rem- of gaspedaal terecht kan komen. Condens en vocht kunnen de werking van de speler tijdelijk negatief beïnvloeden. Laat de speler in een warmere omgeving ongeveer een uur op temperatuur komen. Veeg vochtige schijven met een zachte doek schoon. Sommige discs kunnen niet worden afgespeeld afhankelijk van het type disc, de indeling ervan, de toepassing waarmee deze is opgenomen, de omgeving waarin deze wordt afgespeeld, de manier waarop deze wordt bewaard, enzovoort. Schokken tijdens het rijden van het voertuig kunnen de disc laten overslaan. ERROR-23 Het USB-opslagapparaat was niet geformatteerd met de indeling FAT12, FAT16 of FAT32. Gebruik een USB-opslagapparaat dat geformatteerd is met de indeling FAT12, FAT16 of FAT32. Raak de gegevenszijde van de disc niet aan. Bij gebruik van discs met een bedrukbaar labeloppervlak moet u de instructies en waarschuwingen van de discs controleren. Afhankelijk van de disc kan laden of uitwerpen niet mogelijk zijn. Het gebruik van zulke discs kan dit toestel beschadigen. Plak geen in de handel verkrijgbare labels of andere materialen op de discs. ! De discs kunnen vervormen waardoor ze onafspeelbaar kunnen worden. ! De labels kunnen loslaten tijdens het afspelen en de disc blokkeren bij het uitwerpen en het toestel beschadigen. Afhankelijk van het USB-opslagapparaat kunnen de volgende problemen voorkomen. ! De bediening kan verschillend zijn. ! Het opslagapparaat wordt niet herkend. ! Bestanden worden niet correct afgespeeld. ! Het toestel kan hoorbare interferentie veroorzaken wanneer u naar de radio luistert. iPod Stel de iPod niet bloot aan hoge temperaturen. Maak de iPod stevig vast voordat u gaat rijden. Zorg dat de iPod niet op de grond kan vallen omdat hij dan onder het rem- of gaspedaal terecht kan komen. Informatie over iPod-instellingen ! Wanneer een iPod is aangesloten, wordt de equalizer van de iPod door dit toestel uitgeschakeld voor een optimale klankweergave. Als u de iPod loskoppelt, wordt de equalizer naar de oorspronkelijke instelling teruggezet. ! Tijdens gebruik van dit toestel kunt u de herhaalfunctie op de iPod niet uitschakelen. De herhaalfunctie wordt automatisch ingesteld op Alle als u de iPod op dit toestel aansluit. Tekst op de iPod die niet compatibel is met de specificaties van dit toestel kan niet worden weergegeven. Nl <QRD3247-B> 100 Black plate (101,1) Aanhangsel Aanvullende informatie Compatibiliteit met gecomprimeerde audio (disc, USB) WMA Bestandsextensie: .wma Bitsnelheid: 48 kbps tot 320 kbps (CBR), 48 kbps tot 384 kbps (VBR) Bemonsteringsfrequentie: 32 kHz, 44,1 kHz, 48 kHz Windows Mediaä Audio Professional, Lossless, Voice/DRM Stream/Stream met video: Niet compatibel MP3 Bestandsextensie: .mp3 Aanvullende informatie Bijkomende informatie Alleen de eerste 32 tekens van de bestandsnaam (inclusief de extensie) of mapnaam worden weergegeven. Mappenhiërarchie: maximaal acht niveaus diep (Voor praktisch gebruik kunt u beter niet meer dan twee niveaus gebruiken.) Russische tekst kan alleen op dit toestel worden weergegeven als die met een van de volgende tekensets is gecodeerd: ! Unicode (UTF-8, UTF-16) ! Andere tekensets dan Unicode die in een Windows-omgeving worden gebruikt en op Russisch zijn ingesteld bij de taalinstellingen Afspeelbare mappen: maximaal 500 Een juiste werking van dit toestel is afhankelijk van de toepassing waarmee de WMA-bestanden zijn gecodeerd. Er kan een beetje vertraging optreden bij het beginnen met afspelen van audiobestanden met beeldgegevens of bestanden op een USB-opslagapparaat met een uitgebreide mappenstructuur. Bitsnelheid: 8 kbps tot 320 kbps (CBR), VBR Bemonsteringsfrequentie: 8 kHz tot 48 kHz (32 kHz, 44,1 kHz, 48 kHz voor de beste kwaliteit) Compatibele ID3-tag-versie: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3-tag versie 2.x krijgt prioriteit boven versie 1.x.) M3u speellijst: Niet compatibel MP3i (MP3 interactive), mp3 PRO: Niet compatibel Disc Mappenhiërarchie: maximaal acht niveaus diep (Voor praktisch gebruik kunt u beter niet meer dan twee niveaus gebruiken.) Afspeelbare mappen: maximaal 99 Quantisatiebits: 8 en 16 (LPCM), 4 (MS ADPCM) Bemonsteringsfrequentie: 16 kHz tot 48 kHz (LPCM), 22,05 kHz en 44,1 kHz (MS ADPCM) ! U kunt deze functie niet gebruiken met USB MTP. Afspelen van auteursrechtelijk beschermde bestanden: Niet compatibel Gepartitioneerd USB-opslagapparaat: Alleen de eerste partitie kan worden afgespeeld. Bij het starten van audiobestanden op een USBopslagapparaat met een uitgebreide mappenstructuur kan enige vertraging optreden. iPod nano (6e generatie) iPod nano (5e generatie) iPod nano (4e generatie) iPod nano (3e generatie) iPod nano (2e generatie) iPod nano (1e generatie) iPhone 5 iPhone 4S iPhone 4 iPhone 3GS iPhone 3G iPhone Afhankelijk van de generatie en de versie van de iPod zijn sommige functies mogelijk niet beschikbaar. De bediening kan variëren, afhankelijk van de softwareversie van de iPod. LET OP ! Pioneer garandeert geen compatibiliteit met alle USB-opslagapparaten en kan niet verantwoordelijk worden gesteld voor eventueel gegevensverlies op mediaspelers, smartphones of andere apparaten tijdens gebruik van dit product. ! Laat discs en USB-opslagapparaten niet achter op plaatsen waar de temperatuur hoog kan oplopen. Gebruikers van een iPod met Lightning-aansluiting moeten de Lightning-naar-USB-kabel gebruiken (bij de iPod geleverd). Gebruikers van een iPod met dock-connector moeten CD-IU51 gebruiken. Raadpleeg uw leverancier voor meer informatie. Raadpleeg de handleiding van de iPod voor meer informatie over ondersteunde bestandsindelingen. Audioboek, podcast: Compatibel Afspeelbare bestanden: maximaal 999 Bestandssysteem: ISO 9660 Level 1 en 2, Romeo, Joliet Afspelen van multisessie-discs: Compatibel Bestandsextensie: .wav Afspeelbare bestanden: maximaal 15 000 ! ! ! ! ! ! ! ! ! ! ! ! Packet write data transfer: Niet compatibel Bij het afspelen van gecomprimeerde audiodiscs wordt altijd een korte pauze ingelast tussen de fragmenten. Dit gebeurt ongeacht de duur tussen de fragmenten op de originele opname. Compatibiliteit met iPod Alleen de volgende iPods kunnen met dit toestel gebruikt worden. Gemaakt voor ! iPod touch (5e generatie) ! iPod touch (4e generatie) ! iPod touch (3e generatie) ! iPod touch (2e generatie) ! iPod touch (1e generatie) ! iPod classic ! iPod met video ! iPod nano (7e generatie) LET OP Pioneer is niet verantwoordelijk voor verlies van gegevens op de iPod, ook niet tijdens gebruik van dit toestel. Nederlands WAV USB-opslagapparaat Volgorde van audiobestanden De gebruiker kan met dit toestel geen mapnummers toewijzen of de afspeelvolgorde wijzigen. Nl <QRD3247-B> 101 101 Black plate (102,1) Aanhangsel Aanvullende informatie Voorbeeld van een boomstructuur 01 02 1 2 03 3 4 04 5 6 05 Niveau 1 Niveau 2 Niveau 3 Niveau 4 : Map : Gecomprimeerd audiobestand 01 tot 05: Mapnummer 1 tot 6: Afspeelvolgorde S: T S: T S: T S: T S: T :Л :М :Н :О :П :Р :С :Т :У :Ф :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю S: Scherm T: Teken Disc Copyright en handelsmerken De mapvolgorde en andere instellingen zijn afhankelijk van de software die voor het coderen en schrijven is gebruikt. MP3 USB-opslagapparaat De afspeelvolgorde is gelijk aan de volgorde waarin de bestanden zijn opgenomen op het USB-opslagapparaat. Ga als volgt te werk als u wilt dat bestanden in een bepaalde volgorde worden afgespeeld. 1 Geef de bestanden namen met nummers die de afspeelvolgorde aangeven, bijvoorbeeld 001xxx.mp3 en 099yyy.mp3. 2 Plaats de bestanden in een map. 3 Sla de map met bestanden op het USB-opslagapparaat op. Merk echter op dat de afspeelvolgorde niet altijd kan worden bepaald. Dit is afhankelijk van het gebruikte systeem. De afspeelvolgorde op draagbare USB-audiospelers is verschillend en hangt af van de gebruikte audiospeler. Lijst van Russische tekens 102 Aanvullende informatie S: T S: T S: T S: T S: T :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К “Gemaakt voor iPod” en “Gemaakt voor iPhone” wil zeggen dat een elektronische accessoire speciaal ontwikkeld is voor verbinding met respectievelijk een iPod of iPhone en door de maker gewaarborgd is als conform de Apple werkingsnormen. Apple is niet verantwoordelijk voor de werking van dit apparaat en voor het voldoen aan de veiligheidsnormen en wettelijke normen. Houd er rekening mee dat het gebruik van dit accessoire met iPod of iPhone invloed kan hebben op de draadloze prestatie. Androidä Android is een handelsmerk van Google Inc. Dit product is uitsluitend bedoeld voor niet-commercieel privégebruik. Het mag niet in een commerciële omgeving worden gebruikt voor realtime-uitzendingen (over land, via satelliet, kabel en/of andere media), voor uitzendingen/ streaming via internet, intranet en/of andere netwerken, of in andere elektronische distributiesystemen zoals betaalradio of audio-opaanvraagtoepassingen. Hiervoor is een aparte licentie nodig. Kijk voor meer informatie op http://www.mp3licensing.com. WMA Windows Media is een gedeponeerd handelsmerk of een handelsmerk van Microsoft Corporation in de Verenigde Staten en/of in andere landen. Dit product bevat technologie die het eigendom is van Microsoft Corporation en die niet gebruikt of gedistribueerd mag worden zonder toestemming van Microsoft Licensing, Inc. iPod & iPhone iPhone, iPod, iPod classic, iPod nano en iPod touch zijn handelsmerken van Apple Inc., gedeponeerd in de VS en andere landen. Lightning is een handelsmerk van Apple Inc. Nl <QRD3247-B> 102 Black plate (103,1) Aanhangsel Aanvullende informatie Technische gegevens Algemeen Spanningsbron ................ 14,4 V gelijkstroom (10,8 tot 15,1 V toelaatbaar) Negatief Aarding ........................... Maximaal stroomverbruik ................................... Afmetingen (B × H × D): DIN Chassis ............................ Voorkant .......................... D Chassis ............................ Voorkant .......................... Gewicht ........................... 10,0 A 178 mm × 100 mm × 157 mm 188 mm × 118 mm × 25 mm 178 mm × 100 mm × 165 mm 170 mm × 96 mm × 17 mm 1,2 kg Audio Cd-speler Systeem ........................... Bruikbare discs ................ Signaal-tot-ruisverhouding ................................... Aantal kanalen ................. Compact Disc Audio Compact Discs 94 dB (1 kHz) (IEC-A-netwerk) 2 (stereo) USB USB-specificatie .............. USB 2.0 volledige snelheid Maximaal stroomverbruik ................................... 1 A USB-klasse ...................... MSC-apparatuur (Mass Storage Class) Bestandssysteem ............. FAT12, FAT16, FAT32 MP3-decoderingsformaat ................................... MPEG-1 & 2 Audio Layer 3 WMA-decoderingsformaat ................................... Versie 7, 7.1, 8, 9, 10, 11, 12 (2 kan. audio) (Windows Media Player) WAV-signaalformaat ........ Lineaire PCM & MS ADPCM (niet gecomprimeerd) FM-tuner Frequentiebereik .............. 87,5 MHz tot 108,0 MHz Bruikbare gevoeligheid .... 9 dBf (0,8 µV/75 W, mono, S/R: 30 dB) Signaal-tot-ruisverhouding ................................... 72 dB (IEC-A-netwerk) MW-tuner Frequentiebereik .............. 531 kHz tot 1 602 kHz Bruikbare gevoeligheid .... 25 µV (S/R: 20 dB) Signaal-tot-ruisverhouding ................................... 62 dB (IEC-A-netwerk) Nederlands Maximaal uitgangsvermogen ................................... 50 W × 4 70 W × 1/2 W (voor de subwoofer) Doorlopend uitgangsvermogen ................................... 22 W × 4 (50 Hz tot 15 000 Hz, 5% THD, 4 W belasting, beide kanalen) Belastingsimpedantie ...... 4 W (4 W tot 8 W toegestaan) Preout maximaal uitgangsniveau ................................... 2,0 V Contouren loudness ......... +10 dB (100 Hz), +6,5 dB (10 kHz) (volume: –30 dB) Equalizer (grafische equalizer met vijf banden): Frequentie ....................... 80 Hz/250 Hz/800 Hz/2,5 kHz/ 8 kHz Bereik equalizer ............... ±12 dB (in stappen van 2 dB) Subwoofer (mono): Frequentie ....................... 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Helling ............................. –12 dB/oct, –24 dB/oct Gain ................................ +6 dB tot –24 dB Fase ................................. Normaal/tegengesteld MP3-decoderingsformaat ................................... MPEG-1 & 2 Audio Layer 3 WMA-decoderingsformaat ................................... Versie 7, 7.1, 8, 9, 10, 11, 12 (2 kan. audio) (Windows Media Player) WAV-signaalformaat ........ Lineaire PCM & MS ADPCM (niet gecomprimeerd) LW-tuner Frequentiebereik .............. 153 kHz tot 281 kHz Bruikbare gevoeligheid .... 28 µV (S/R: 20 dB) Signaal-tot-ruisverhouding ................................... 62 dB (IEC-A-netwerk) Opmerking Technische gegevens en ontwerp kunnen zonder voorafgaande kennisgeving worden gewijzigd. Nl <QRD3247-B> 103 103 Black plate (104,1) Раздел Перед началом эксплуатации 01 Благодарим Вас за покупку этого изделия компании PIONEER Для обеспечения правильности эксплуатации внимательно прочитайте данное руководство перед началом использования изделия. Особенно важно, чтобы Вы прочли и соблюдали инструкции, помеченные в данном руководстве заголовками ПРЕДУПРЕЖДЕНИЕ и ВНИМАНИЕ. Держите данное руководство под рукой для обращения к нему в будущем. шего изделия с соблюдением обязательных процедур по обработке, утилизации и вторичной переработке и, таким образом, предотвратите потенциальное негативное воздействие на окружающую среду и здоровье людей. Дату изготовления оборудования можно определить по серийному номеру, который содержит информацию о месяце и годе производства. Если вы желаете утилизировать данное изделие, не выбрасывайте его вместе с обычным бытовым мусором. Существует отдельная система сбора использованных электронных изделий в соответствии с законодательством, которая предполагает соответствующее обращение, возврат и переработку. Частные лица в странах Евросоюза, Швейцарии и Норвегии могут бесплатно возвращать использованные электронные изделия в специализированные пункты приема или в магазин (при покупке аналогичного нового устройства). Если Ваша страна не указана в приведенном выше перечне, обращайтесь в органы местного управления за инструкциями по правильной утилизации продукта. Тем самым Вы обеспечите утилизацию Ва- Сведения об этом устройстве Частоты тюнера в этом устройстве распределены для использования в Западной Европе, Азии, на Ближнем Востоке, в Африке и Океании. При использовании в других регионах качество приема может быть плохим. Функция RDS (радиовещательная система передачи информации) работает только в регионах, где транслируются сигналы RDS для FM-станций. Перед началом эксплуатации ПРЕДУПРЕЖДЕНИЕ ! Не пытайтесь самостоятельно производить установку или ремонт изделия. Установка или ремонт изделия лицами, не обладающими специальными навыками и опытом работы с электронным оборудованием и автомобильными аксессуарами, могут создать опасность поражения электрическим током или иных инцидентов. ! Ни в коем случае не пытайтесь управлять устройством во время движения. Прежде чем использовать органы управления устройством, необходимо съехать с дороги и припарковать автомобиль в безопасном месте. При возникновении проблем При неполадках в работе этого изделия свяжитесь с торговым представителем компании-производителя или с ближайшим сервисным пунктом PIONEER. ВНИМАНИЕ ! Не допускайте попадания жидкости на устройство. Это может повлечь поражение электрическим током. Кроме того, попадание жидкости в устройство может стать причиной его выхода из строя, перегрева и появления дыма. ! Pioneer CarStereo-Pass предназначен для использования только в Германии. ! Всегда сохраняйте уровень громкости достаточно низким, чтобы были слышны звуки извне. ! Не допускайте воздействия влажности на изделие. ВНИМАНИЕ Данное изделие является лазерным изделием класса 1 согласно классификации по Безопасности лазерных изделий, IEC 60825-1:2007. ЛАЗЕРНЫЙ ПРОДУКТ КЛАСС 1 104 Ru <QRD3247-B> 104 Black plate (105,1) Раздел Использование данного устройства Основное устройство 1 2 3 4 5 Использование данного устройства ВНИМАНИЕ Для подключения запоминающих устройств USB используйте USB-кабель Pioneer (CDU50E, приобретается отдельно), поскольку любое устройство при подключении напрямую выступает из устройства, что создает потенциальную опасность. a Индикация на дисплее 2 1 6 7 89 4 5 6 7 9 8 b a b cd 1 h (извлечение) 2 iPod 3 С 1/ 4 Щель для загрузки диска 5 DISP 6 SRC/OFF 7 BAND/ 8 c/d 9 MULTI-CONTROL (M.C.) a (назад)/DIMMER (регулятор освещенности) b 3 по 6/ a 1 2 (управление iPod) (список) c Вход AUX (стереоразъем 3,5 мм) d USB порт b (список) (управление iPod) Управление функциями iPod производится с устройства iPod. 3 Сектор дополнительной информации 4 TA (дорожные сводки) 5 TP (идентификатор дорожных программ) 6 (sound retriever, технология преобразования звука) 7 LOC (настройка с местным поиском) 8 9 (повтор) (в произвольной последовательности) Сектор основной информации ! Тюнер: диапазон и частота ! RDS: название программы, PTY-информация и прочая текстовая информация ! Проигрыватель компакт-дисков, запоминающее устройство USB и iPod: время, прошедшее с начала воспроизведения, и текстовая информация Отображается при наличии нижнего уровня папки или меню. Установочное меню 1 После установки устройства поверните ключ зажигания в положение ON. Появится надпись SET UP. 2 Поверните M.C. для выбора YES. # Если в течение 30 секунд устройство не используется, установочное меню не будет выводиться. # Если вы хотите выполнить настройку позже, поверните M.C., чтобы выбрать NO. 3 Нажмите M.C. для выбора. 4 Настройте меню с помощью описанных ниже действий. Для перехода к следующему пункту меню необходимо подтвердить выбор. 02 LANGUAGE (выбор языка) Данное устройство может отображать текстовую информацию из сжатых аудиофайлов, в том числе информацию на английском, русском и турецком языках. ! При несовместимости настроек встроенного и выбранного языка возможны искажения при выводе текстовых сообщений. ! Некоторые символы могут отображаться неправильно. 1 Поворачивайте M.C. для выбора настройки. ENG (английский)—РУС (русский)—TUR (турецкий) 2 Нажмите M.C., чтобы подтвердить выбор. CLOCK SET (установка часов) 1 Поворачивайте M.C., чтобы установить часы. 2 Нажимайте M.C., чтобы выбрать установку минут. 3 Поворачивайте M.C., чтобы установить минуты. 4 Нажмите M.C., чтобы подтвердить выбор. FM STEP (шаг настройки в FM-диапазоне) Ru <QRD3247-B> 105 Русский Для установки шага настройки в FM-диапазоне (настройки поиска) используйте меню FM STEP. 1 Поверните M.C., чтобы выбрать шаг настройки в FM-диапазоне. 100 (100 кГц)—50 (50 кГц) 2 Нажмите M.C., чтобы подтвердить выбор. Появится надпись QUIT. ! Шаг ручной настройки фиксированный и составляет 50 кГц. ! При выключении функций AF и TA шаг настройки автоматически меняется на 50 кГц, даже если установлено 100. 105 Black plate (106,1) Раздел Использование данного устройства 02 5 Чтобы закончить настройку, поверните M.C. и выберите YES. # Если понадобится вновь изменить настройку, поверните M.C. и выберите NO. 6 Нажмите M.C. для выбора. Примечания ! Настроить параметры меню можно в меню системы и в начальном меню. Более подробную информацию см. в разделах Меню системы на стр. 112 и Стартовое меню на стр. 113. ! Вы можете отменить настройку параметра, нажав кнопку SRC/OFF. Основные операции Включение устройства 1 Нажмите кнопку SRC/OFF, чтобы включить устройство. Выключение устройства 1 Нажмите и удерживайте кнопку SRC/OFF, пока устройство не выключится. Выбор источника сигнала 1 Нажимайте кнопку SRC/OFF для выбора из следующих функций: RADIO—CD—USB/iPod—APP (приложение) —AUX ! При подключении по протоколу MTP на дисплее отображается USB MTP. ! Если подключен iPod и выбран любой источник сигнала, кроме iPod, можно переключиться на iPod с помощью кнопки iPod. Регулировка громкости 1 Для регулировки громкости поворачивайте M.C. 106 Примечание Когда голубой/белый провод этого устройства подключен к реле панели управления автомобильной антенной, антенна на автомобиле выдвигается при включении источника сигнала этого устройства. Чтобы втянуть антенну, выключите источник сигнала. Часто используемые элементы меню Возврат к предыдущему дисплею Возврат к предыдущему списку (к папке на один уровень выше) /DIMMER. 1 Нажмите кнопку Возврат в исходный режим Выход из главного меню 1 Нажмите кнопку BAND/ . Возврат в исходный режим из списка 1 Нажмите кнопку BAND/ . Радиоприемник Основные операции Выбор диапазона 1 Нажимайте кнопку BAND/ , пока на дисплее не отобразится нужный диапазон (FM1, FM2, FM3 для FM или MW/LW). Переключение станций предварительной настройки 1 Нажмите кнопку c или d. ! Чтобы использовать эту функцию, в меню SEEK выберите PCH (запрограммированная станция). Использование данного устройства Ручная настройка (пошаговая) 1 Нажмите кнопку c или d. ! Чтобы использовать эту функцию, в меню SEEK выберите MAN (ручная настройка). Поиск 1 Нажмите и удерживайте кнопку c или d, а затем отпустите. Вы можете отменить настройку с поиском кратким нажатием c или d. При нажатии и удерживании кнопки c или d можно пропускать радиостанции. Настройка с поиском начнется сразу после отпускания кнопки c или d. Примечания ! Подробную информацию о меню SEEK см. в разделе SEEK (настройка левой и правой кнопок) на стр. 107. ! Можно включить или выключить функцию AF (поиск альтернативных частот) данного устройства. Для обычной настройки функция AF должна быть выключена (смотрите в AF (поиск альтернативных частот) на стр. 107). Сохранение и вызов из памяти радиостанций для каждого диапазона Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! FREQUENCY (служебное название программы или частота) ! BRDCST INFO (служебное название программы/информация PTY) ! CLOCK (название источника сигнала и часы) Примечания ! Если служебное название программы в поле FREQUENCY отсутствует, вместо него отображается канал. Если служебное название программы обнаружено, оно будет отображаться. ! Текстовая информация может меняться в зависимости от диапазона. ! Возможность внесения изменений в текстовую информацию зависит от региона. Использование функций PTY Можно настроиться на радиостанцию с помощью информации PTY (типа программы). Использование кнопок предварительной настройки 1 Сохранение: нажмите и удерживайте одну из кнопок предварительной настройки (с 1/ по 6/ ), пока номер не прекратит мигать. 2 Вызов: нажмите одну из кнопок предварительной настройки (с 1/ по 6/ ). Ru <QRD3247-B> 106 Black plate (107,1) Раздел Использование данного устройства Поиск станции RDS с помощью информации PTY (список). 1 Нажмите 2 Кнопкой M.C. выберите тип программы. NEWS/INFO—POPULAR—CLASSICS—OTHERS 3 Нажмите M.C., чтобы начать поиск. Устройство начинает поиск радиостанций, передающих данный тип программ. При обнаружении радиостанции на дисплее будет показано название данной программы. ! Для отмены поиска нажмите M.C. еще раз. ! Программы некоторых радиостанций могут отличаться от программ, указанных в передаваемом коде PTY. ! Если ни одна из станций не передает программы нужного типа, то на дисплее в течение примерно двух секунд будет показано NOT FOUND, и затем тюнер перейдет в режим приема станции, с которой был начат поиск. Список PTY Более подробную информацию о списке PTY можно получить на веб-сайте: http://www.pioneer.eu/eur/products/25/121/tech/ CarAudio/PTY.html Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. # В диапазонах MW/LW можно выбрать только BSM, LOCAL и SEEK. FM SETTING (настройки качества звука FM) Уровень качества звука можно установить в соответствии с условиями приема сигнала в FM-диапазоне. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора настройки. ! STANDARD – стандартная настройка. ! HI-FI – настройка с приоритетом высокого качества стереозвучания. ! STABLE – настройка с приоритетом низкого уровня помех монофонического звучания. BSM (запоминание лучших станций) Функция BSM (запоминание лучших станций) позволяет автоматически сохранять в памяти устройства шесть станций с самым мощным сигналом в порядке убывания его мощности. 1 Нажмите M.C., чтобы включить функцию BSM. Для отмены режима нажмите M.C. еще раз. REGIONAL (региональный) При использовании функции AF функция региональных программ ограничивает выбор станциями, транслирующими региональные программы. 1 Нажмите M.C., чтобы включить или выключить функцию региональных программ. Настройка с местным поиском позволяет Вам настраиваться только на радиостанции с достаточно мощными сигналами для качественного приема. 1 Нажмите M.C. для выбора нужной настройки. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Настройка самого высокого уровня позволяет осуществлять прием только станций с самым сильным сигналом, а уменьшение уровня настройки позволяет принимать станции с более слабым сигналом. TA (режим ожидания дорожных сводок) 1 Нажмите M.C., чтобы включить или выключить режим ожидания дорожных сводок. AF (поиск альтернативных частот) 1 Нажмите M.C., чтобы включить или выключить функцию AF. NEWS (прерывание для передачи новостей) 1 Нажмите M.C., чтобы включить или выключить функцию НОВОСТИ. SEEK (настройка левой и правой кнопок) Правой и левой кнопкам на устройстве можно назначить определенную функцию. Выберите MAN (ручная настройка) для ручной настройки или PCH (предустановленный канал) для переключения между заранее настроенными каналами. 1 Нажмите кнопку M.C., чтобы выбрать MAN или PCH. 02 CD/CD-R/CD-RW и запоминающие устройства USB Подключение по протоколу MTP Устройства Android, поддерживающие протокол MTP (с операционной системой Android OS 4.0 или выше), можно подключить по протоколу MTP как USB-устройство. Для подключения используйте кабель, входящий в комплект поставки устройства Android. Примечание Эта функция не поддерживает WAV. Основные операции Воспроизведение CD/CD-R/CD-RW 1 Вставьте диск в щель для загрузки маркированной стороной вверх. Извлечение диска CD/CD-R/CD-RW 1 Нажмите h. Воспроизведение композиций на запоминающем устройстве USB 1 Откройте крышку порта USB. 2 Подключите запоминающее устройство USB с помощью кабеля USB. Остановка воспроизведения файлов на запоминающем устройстве USB 1 Запоминающее устройство USB можно отключить в любой момент. Выбор папки 1 Нажмите кнопку 1/ или 2/ . Выбор дорожки 1 Нажмите кнопку c или d. Русский 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. 3 Для выбора функции поворачивайте M.C. Следующие выбранные функции можно настраивать. Использование данного устройства LOCAL (настройка с местным поиском) Ru <QRD3247-B> 107 107 Black plate (108,1) Раздел Использование данного устройства 02 Ускоренная перемотка вперед или назад 1 Нажмите и удерживайте кнопку c или d. ! При воспроизведении сжатых аудиофайлов звук не воспроизводится, если включена ускоренная перемотка вперед или назад. Возврат к корневой папке 1 Нажмите и удерживайте кнопку BAND/ . Переключение между сжатыми аудиофайлами и диском CD-DA 1 Нажмите кнопку BAND/ . Переключение между запоминающими устройствами При наличии нескольких запоминающих устройств USB Mass Storage воспроизведение можно переключать между ними. 1 Нажмите кнопку BAND/ . ! Возможно переключение между 32 различными запоминающими устройствами. Примечание Если запоминающее устройство USB не используется, отключите его. Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: CD-DA ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) CD-TEXT ! TRACK INFO (название дорожки/исполнитель/название диска) ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) MP3/WMA/WAV ! TRACK INFO (название дорожки/имя исполнителя/название альбома) ! FILE INFO (название папки/название файла) ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) Выбор и воспроизведение фалов/дорожек из списка 1 Нажмите кнопку , чтобы отобразить список названий файлов/дорожек. 108 Использование данного устройства 2 С помощью M.C. выберите нужное имя файла (или папки). Выбор файла или папки 1 Поворачивайте M.C. Воспроизведение 1 Выберите файл или дорожку и нажмите M. C. Просмотр списка названий файлов (папок) в выбранной папке 1 Выберите папку и нажмите M.C. Воспроизведение композиции из выбранной папки 1 Выберите папку, затем нажмите и удерживайте M.C. Функции с использованием специальных кнопок Выбор диапазона повторного воспроизведения 1 Нажимайте кнопку 6/ для выбора из следующих функций: CD/CD-R/CD-RW ! ALL – Повторное воспроизведение всех дорожек ! ONE – Повтор текущей дорожки ! FLD – Повтор текущей папки Запоминающее устройство USB ! ALL – Повтор всех файлов ! ONE – Повтор текущего файла ! FLD – Повтор текущей папки Воспроизведение дорожек в произвольной последовательности , чтобы включить или 1 Нажмите кнопку 5/ выключить функцию воспроизведения в произвольной последовательности. Данная функция позволяет воспроизводить дорожки в произвольной последовательности в пределах выбранного диапазона повторного воспроизведения. ! Для переключения на следующую дорожку во время воспроизведения в произвольной последовательности нажмите кнопку d. При нажатии на кнопку c воспроизведение текущей дорожки начинается с начала. Приостановка воспроизведения 1 Нажмите кнопку 4/PAUSE, чтобы включить паузу или возобновить воспроизведение. Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) 1 Нажимайте кнопку 3/S.Rtrv для выбора из следующих функций: 1—2—OFF (выкл) Настройка 1 эффективна для файлов с низкой степенью сжатия, а настройка 2 – для файлов с высокой степенью сжатия. Ru <QRD3247-B> 108 Black plate (109,1) Раздел Использование данного устройства Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. Выбранные функции, которые можно настраивать, перечислены ниже. S.RTRV (sound retriever, технология преобразования звука) Автоматически улучшает качество звука сжатых аудиофайлов и восстанавливает полноту звучания. 1 Нажмите M.C. для выбора нужной настройки. Подробную информацию см. в Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) на стр. 108. Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! TRACK INFO (название дорожки/имя исполнителя/название альбома) ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) Поиск композиции iPod Основные операции Воспроизведение музыки на iPod 1 Откройте крышку порта USB. 2 Подключите iPod к разъему USB. Воспроизведение начинается автоматически. Выбор композиции (раздела) 1 Нажмите кнопку c или d. или 2/ . Ускоренная перемотка вперед или назад 1 Нажмите и удерживайте кнопку c или d. 1 Для перехода к главному меню поиска по списку нажмите . 2 С помощью M.C. выберите категорию/ композицию. Выбор названия композиции или категории 1 Поворачивайте M.C. Плейлисты—исполнители—альбомы—композиции—подкасты—жанры—композиторы—аудиокниги Воспроизведение 1 Выберите композицию и нажмите M.C. Воспроизведение композиции в выбранной категории 1 Выберите категорию, затем нажмите и удерживайте M.C. Поиск в списке по алфавиту 1 Когда список выбранной категории отобразится на дисплее, нажмите , чтобы включить режим поиска по алфавиту. ! Дважды повернув M.C., можно перейти в режим поиска по алфавиту. 2 Для выбора буквы поворачивайте M.C. 3 Нажмите M.C. для отображения списка по алфавиту. ! Для отмены поиска нажмите /DIMMER. Примечания ! Можно воспроизводить списки воспроизведения, созданные с помощью приложения для компьютера (MusicSphere). Приложение можно скачать на нашем сайте. ! Списки воспроизведения, созданные с помощью приложения (MusicSphere), будут отображаться в сокращенном виде. 02 Функции с использованием специальных кнопок Выбор диапазона повторного воспроизведения 1 Нажимайте кнопку 6/ для выбора из следующих функций: ! ONE – повтор текущей композиции ! ALL – повтор всех композиций в выбранном списке ! Если выбран режим управления CTRL iPod, диапазон повторного воспроизведения будет аналогичным установленному для подключенного iPod. Выбор диапазона воспроизведения в произвольной последовательности (“перемешать”) для выбора из 1 Нажимайте кнопку 5/ следующих функций: ! SNG – воспроизведение композиций из выбранного списка в произвольной последовательности. ! ALB – воспроизведение по порядку композиций из альбома, выбранного случайным образом. ! OFF – отмена воспроизведения в произвольной последовательности. Воспроизведение всех композиций в произвольной последовательности (“перемешать все”) /5, 1 Нажмите и удерживайте кнопку чтобы включить функцию “перемешать все”. ! Чтобы отключить функцию “перемешать все”, выберите OFF в меню перемешивания. Подробнее см. в разделе Выбор диапазона воспроизведения в произвольной последовательности (“перемешать”) на стр. 109. Русский Выбор альбома 1 Нажмите кнопку 1/ Примечания ! iPod можно включить или выключить, если выбран режим управления CTRL AUDIO. ! Перед подключением iPod к данному устройству отсоедините от него наушники. ! Выключение iPod происходит примерно через две минуты после выключения зажигания. Использование данного устройства Просмотр списка композиций в выбранной категории 1 Выберите категорию и нажмите M.C. Ru <QRD3247-B> 109 109 Black plate (110,1) Раздел Использование данного устройства 02 Приостановка воспроизведения 1 Нажмите кнопку 4/PAUSE, чтобы включить паузу или возобновить воспроизведение. Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) 1 Нажимайте кнопку 3/S.Rtrv для выбора из следующих функций: 1—2—OFF (выкл) Настройка 1 эффективна для файлов с низкой степенью сжатия, а настройка 2 – для файлов с высокой степенью сжатия. Воспроизведение композиций в жанре воспроизводимой в данный момент композиции Можно воспроизводить композиции из следующих списков. • Список альбомов артиста, композиция которого воспроизводится в данный момент • Список композиций, относящихся к воспроизводимому в данный момент альбому • Список альбомов, относящихся к воспроизводимому в данный момент музыкальному жанру 1 Нажмите и удерживайте кнопку для переключения в режим воспроизведения по категории. 2 Для изменения режима вращайте M.C., для выбора – нажмите. ! ARTIST – Воспроизведение альбома артиста, композиция которого воспроизводится в данный момент. ! ALBUM – Воспроизведение композиции из альбома, который воспроизводится в данный момент. ! GENRE – Воспроизведение альбома в жанре, который воспроизводится в данный момент. 110 Выбранная композиция или альбом будет воспроизводиться после окончания воспроизведения текущей композиции. Примечания ! Возможна отмена воспроизведения выбранной композиции/альбома, если вы используете любые другие функции, кроме поиска по категории (например, перемотка вперед или назад). ! В зависимости от того, какая композиция выбрана, конец текущей композиции и начало выбранной композиции/альбома могут быть обрезаны. Использование функций iPod данного устройства на вашем iPod Управление функциями iPod данного устройства может производиться с подключенного iPod. Режим CTRL iPod несовместим со следующими моделями iPod: ! iPod nano 1-го поколения ! iPod с поддержкой видео % Переключение между режимами управления производится нажатием BAND/ . ! CTRL iPod – управление функциями iPod данного устройства может производиться с подключенного iPod. ! CTRL AUDIO – управление функциями iPod данного устройства может производиться с помощью органов управления данного устройства. Переключение режима управления также производится нажатием кнопки iPod. Примечания ! При переключении на режим управления CTRL iPod воспроизведение композиции приостанавливается. Чтобы возобновить воспроизведение, используйте iPod. Использование данного устройства ! Следующими функциями можно управлять с данного устройства, даже если выбран режим управления CTRL iPod. — Пауза — Ускоренная перемотка вперед/назад — Выбор композиции (раздела) ! Громкость можно регулировать только с основного устройства. Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. 3 Для выбора функции поворачивайте M.C. Следующие выбранные функции можно настраивать. S.RTRV (sound retriever, технология преобразования звука) 1 Нажмите M.C. для выбора нужной настройки. Подробную информацию см. в Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) на стр. 110. Использование приложений на подсоединенном устройстве Это устройство можно использовать для потокового воспроизведения и управления композициями на iPhone с помощью приложений или только для потокового воспроизведения. ! Функция AUDIO BOOK недоступна, если в качестве режима воспроизведения выбрано CTRL iPod. Подробнее см. в разделе Использование функций iPod данного устройства на вашем iPod на стр. 110. AUDIO BOOK (скорость воспроизведения аудиокниги) 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C., чтобы выбрать нужную настройку. ! FASTER – Ускоренное воспроизведение ! NORMAL – Воспроизведение с обычной скоростью ! SLOWER – Замедленное воспроизведение Ru <QRD3247-B> 110 Black plate (111,1) Раздел Использование данного устройства Важно Использование приложений сторонних разработчиков может включать в себя или требовать предоставления личных данных (создание профиля пользователя или другие способы), а для некоторых приложений - предоставления данных о местонахождении. ВСЕ ПРИЛОЖЕНИЯ СТОРОННИХ РАЗРАБОТЧИКОВ НАХОДЯТСЯ В СФЕРЕ ОТВЕТСТВЕННОСТИ ЭТИХ РАЗРАБОТЧИКОВ, ЧТО БЕЗ ОГРАНИЧЕНИЙ ВКЛЮЧАЕТ В СЕБЯ СБОР И БЕЗОПАСНОСТЬ ПОЛЬЗОВАТЕЛЬСКИХ ДАННЫХ И ОБРАЩЕНИЕ С ЧАСТНОЙ ИНФОРМАЦИЕЙ. ПРИ ИСПОЛЬЗОВАНИИ ПРИЛОЖЕНИЙ СТОРОННИХ РАЗРАБОТЧИКОВ ВЫ СОГЛАШАЕТЕСЬ С УСЛОВИЯМИ ПРЕДОСТАВЛЕНИЯ СЕРВИСА И ПОЛИТИКОЙ КОНФИДЕНЦИАЛЬНОСТИ РАЗРАБОТЧИКОВ. ЕСЛИ ВЫ НЕ СОГЛАСНЫ С УСЛОВИЯМИ ИЛИ ПОЛИТИКОЙ РАЗРАБОТЧИКА ИЛИ НЕ ЖЕЛАЕТЕ ПРЕДОСТАВЛЯТЬ ДАННЫЕ О СВОЕМ МЕСТОНАХОЖДЕНИИ, КОГДА ЭТО ТРЕБУЕТСЯ, НЕ ИСПОЛЬЗУЙТЕ ТАКОЕ ПРИЛОЖЕНИЕ. Сведения о совместимости подключаемых устройств Ниже приводится подробная информация о разъемах, необходимых для использования приложений с iPhone на этом устройстве. Для пользователей iPhone Порядок запуска для пользователей iPhone 1 Подключите iPhone к разъему USB. 2 Переключите источник сигнала на APP. 3 Запустите приложение на iPhone и включите воспроизведение. Основные операции Выбор дорожки 1 Нажмите кнопку c или d. Ускоренная перемотка вперед или назад 1 Нажмите и удерживайте кнопку c или d. Приостановка воспроизведения 1 Нажмите кнопку BAND/ , чтобы включить паузу или возобновить воспроизведение. Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! TRACK INFO (название дорожки/имя исполнителя/название альбома) ! APP NAME (название приложения) ! ELAPSED TIME (время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. 3 Для выбора функции поворачивайте M.C. Следующие выбранные функции можно настраивать. PAUSE (пауза) 1 Нажмите M.C., чтобы включить паузу или возобновить воспроизведение. S.RTRV (sound retriever, технология преобразования звука) 1 Нажмите M.C. для выбора нужной настройки. 1—2—OFF (выкл.) Настройка 1 эффективна для файлов с низкой степенью сжатия, а настройка 2 – для файлов с высокой степенью сжатия. 02 Регулировки параметров звука 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать AUDIO. 3 Для выбора аудиофункции поворачивайте M.C. Следующие выбранные аудиофункции можно настраивать. ! Функция FADER недоступна, если в режиме SP-P/O MODE выбрано SUB.W/SUB.W. Подробнее см. в разделе SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 113. ! Функции SUB.W и SUB.W CTRL недоступны, если в режиме SP-P/O MODE выбрано REAR/REAR. Подробнее см. в разделе SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 113. ! Функция SUB.W CTRL недоступна, если в режиме OFF выбрано SUB.W. Подробнее см. в разделе SUB.W (включение/выключение сабвуфера) на стр. 112. ! Функция SLA недоступна, если в качестве источника сигнала выбрано FM. FADER (регулировка баланса) 1 Для отображения установочного меню нажмите M.C. 2 Нажмите M.C., чтобы отрегулировать баланс передних и задних громкоговорителей. BALANCE (регулировка баланса) 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C., чтобы отрегулировать баланс левого/правого громкоговорителей. EQ SETTING (вызов настроек эквалайзера) Ru <QRD3247-B> 111 Русский ! Данная функция поддерживается iPhone и iPod touch. ! На устройстве установлена iOS 5.0 или более поздней версии. Примечания ! Список совместимых приложений для iPhone см. на нашем сайте. ! Компания Pioneer не несет ответственности за любые проблемы, связанные с некорректными или поврежденными данными приложений. ! За содержимое и функциональность поддерживаемых приложений несут ответственность разработчики приложений. Использование данного устройства 111 Black plate (112,1) Раздел Использование данного устройства 02 1 Для отображения установочного меню нажмите M.C. 2 Нажмите кнопку M.C., чтобы выбрать эквалайзер. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS Полосу и уровень эквалайзера можно отрегулировать, если выбрано CUSTOM1 или CUSTOM2. При выборе CUSTOM1 или CUSTOM2 выполните действия, описанные ниже. При выборе других настроек нажмите M.C., чтобы вернуться к предыдущему дисплею. ! CUSTOM1 можно выбрать отдельно для каждого источника сигнала. Однако для USB, iPod и APP автоматически устанавливаются одинаковые настройки. ! CUSTOM2 - это общая настройка, используемая для всех источников сигнала. 3 Для отображения установочного меню нажмите M.C. 4 Нажимайте M.C. для выбора из следующих функций: Полоса эквалайзера—Уровень эквалайзера 5 Поворачивайте M.C. для выбора настройки. Полоса эквалайзера: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Уровень эквалайзера: от +6 до –6 LOUDNESS (тонкомпенсация) Тонкомпенсация компенсирует недостаточное звуковое давление в нижнем и верхнем диапазонах частот на низкой громкости. 1 Нажмите M.C. для выбора нужной настройки. OFF (выкл)—LOW (низкий)—MID (средний) —HI (высокий) SUB.W (включение/выключение сабвуфера) 112 Это устройство имеет выход канала сабвуфера, который можно включать и выключать. 1 Нажмите M.C. для выбора нужной настройки. NOR (нормальная фаза)—REV (обратная фаза)—OFF (сабвуфер выключен) SUB.W CTRL (настройка сабвуфер) На выходе сабвуфера будут воспроизводиться только те частоты, которые ниже указанных частот среза. 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C. для выбора из следующих функций: Частота среза—Уровень выходного сигнала—Крутизна характеристики Изменяемые значения будут мигать. 3 Поворачивайте M.C. для выбора настройки. Частота среза: 50HZ—63HZ—80HZ—100HZ —125HZ—160HZ—200HZ Уровень выходного сигнала: от –24 до +6 Крутизна характеристики: –12— –24 BASS BOOST (усиление нижних звуковых частот) 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора нужного уровня. При увеличении или уменьшении уровня отображаются надписи с 0 до +6. HPF SETTING (настройка фильтра верхних частот) Использование данного устройства Используйте эту функцию, если вы хотите, чтобы воспроизводились только высокие частоты. На громкоговорители будут выводиться только частоты выше, чем установленные фильтром высоких частот (HPF). 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C. для выбора из следующих функций: Частота среза—Крутизна характеристики 3 Поворачивайте M.C. для выбора настройки. Частота среза: OFF—50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Крутизна характеристики: –12— –24 SLA (регулировка уровня входного сигнала) Эта функция предупреждает скачки громкости при смене источника сигнала. ! Настройки основываются на уровне громкости FM-тюнера, который остается неизменным. ! Регулировку уровня громкости в диапазоне MW/LW также можно производить с помощью данной функции. ! Для USB, iPod и APP автоматически устанавливается одинаковая настройка. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивая M.C., отрегулируйте уровень громкости источника сигнала. Диапазон настройки: от +4 до –4 Меню системы Важно PW SAVE (режим энергосбережения) отключается при отсоединении аккумуляторной батареи автомобиля; при подсоединении батареи его потребуется включить снова. При выключенном режиме PW SAVE (режим энергосбережения) возможно, что, в зависимости от метода подключения, устройство будет потреблять энергию аккумулятора, если зажигание автомобиля не имеет положения АСС. 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 3 Для выбора функции меню системы поворачивайте M.C. Следующие выбранные функции меню системы можно настраивать. LANGUAGE (выбор языка) 1 Нажмите M.C. для выбора нужной настройки. ENG (английский)—РУС (русский)—TUR (турецкий) CLOCK SET (установка часов) 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C., чтобы выбрать сегмент дисплея часов, который нужно установить. Часы—Минуты 3 Поворачивайте M.C., чтобы отрегулировать время. 12H/24H (формат отображения времени) 1 Нажмите M.C. для выбора нужной настройки. 12H (12-часовой)—24H (24-часовой) AUTO PI (автоматический поиск по идентификатору программы) Устройство может автоматически искать другую станцию с такой же программой даже во время вызова предварительной настройки. 1 Нажмите M.C., чтобы включить или выключить автоматический поиск по идентификатору программы. AUX (вспомогательный вход) Ru <QRD3247-B> 112 Black plate (113,1) Раздел Использование данного устройства Активируйте эту настройку при подключении к данному устройству вспомогательного устройства. 1 Нажмите M.C., чтобы включить или выключить функцию AUX. DIMMER (регулятор освещенности) 1 Нажмите M.C., чтобы включить или выключить регулятор освещенности. ! Вы также можете выбрать другую настройку регулятора освещенности, удерживая нажатой кнопку /DIMMER. MUTE MODE (режим приглушения звука) Звук/уровень звукового сигнала данной системы автоматически понижается при получении сигнала от оборудования с функцией приглушения звука. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора настройки. ! MUTE – приглушение звука ! 20dB ATT – ослабление уровня сигнала (20dB ATT имеет более сильный эффект, чем 10dB ATT) ! 10dB ATT – ослабление уровня сигнала PW SAVE (энергосбережение) Включение этой функции позволяет снизить потребляемую мощность аккумуляторной батареи. ! При включении этой функции единственной возможной операцией является включение источника сигнала. 1 Нажмите M.C., чтобы включить или выключить функцию энергосбережения. 1 Нажмите и удерживайте кнопку SRC/ OFF, пока устройство не выключится. 2 Нажмите кнопку SRC/OFF и удерживайте ее, пока не откроется стартовое меню. 4 Для выбора функции меню системы поворачивайте M.C. Следующие выбранные функции стартового меню можно настраивать. FM STEP (шаг настройки в FM-диапазоне) 1 Нажмите M.C., чтобы выбрать шаг настройки в FM-диапазоне. 100 (100 кГц)—50 (50 кГц) SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) Выход на провода заднего громкоговорителя и выход заднего канала RCA можно использовать для подключения широкополосного громкоговорителя или сабвуфера. Выберите настройку, подходящую для Вашего соединения. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора настройки. ! REAR/SUB.W – Выберите, если к выходу заднего канала подсоединен широкополосный громкоговоритель, и также имеется сабвуфер, подсоединенный к выходу RCA. ! SUB.W/SUB.W – Выберите, если сабвуфер подключен напрямую к выходу заднего канала без дополнительного усилителя, и также имеется сабвуфер, подсоединенный к выходу RCA. ! REAR/REAR – Выберите, если широкополосный громкоговоритель подсоединен к выходу заднего канала и к выходу RCA. Если к выходу заднего канала подсоединен широкополосный громкоговоритель, а выход RCA не используется, можно выбрать REAR/SUB.W или REAR/ REAR. Меню системы 1 Нажмите и удерживайте кнопку SRC/ OFF, пока устройство не выключится. 2 Нажмите кнопку SRC/OFF и удерживайте ее, пока не откроется стартовое меню. 3 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 4 Для выбора функции меню системы поворачивайте M.C. Подробную информацию см. в Меню системы на стр. 112. 02 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 3 Поверните M.C., чтобы отобразить DEMO OFF, затем нажмите. 4 Поверните M.C. для выбора YES. 5 Нажмите M.C. для выбора. Использование дополнительного источника сигнала (AUX) 1 Вставьте мини-штекер стереокабеля в гнездо AUX. 2 Нажмите кнопку SRC/OFF, чтобы выбрать AUX в качестве источника сигнала. Примечание Невозможно выбрать AUX, если не включена вспомогательная настройка. Подробную информацию см. в разделе AUX (вспомогательный вход) на стр. 112. Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! Название источника ! Название источника сигнала и часы Русский Стартовое меню 3 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать INITIAL. Использование данного устройства Если открылся неверный экран Отключите неверный экран, как описано ниже. Ru <QRD3247-B> 113 113 Black plate (114,1) Раздел Установка 03 Установка Соединения F O N OF Важно ! При установке данного устройства в автомобиле, в котором отсутствует положение ключа зажигания АСС, красный кабель должен быть подключен к клемме, которая определяет рабочее положение ключа зажигания; в противном случае может возникнуть утечка тока аккумуляторной батареи. STAR T Положение ACC Положение ACC отсутствует ! Эксплуатация данного устройства в условиях, отличных от описанных ниже, может привести к пожару или сбою в работе устройства. — Транспортные средства с 12-вольтовым аккумулятором и заземлением отрицательного полюса. — Громкоговорители с 50 Вт (выходная мощность) и от 4 W до 8 W (сопротивление). ! Во избежание короткого замыкания, перегрева или неисправностей обязательно соблюдайте следующие указания. — Перед установкой отсоедините отрицательную клемму аккумулятора. — Закрепите провода при помощи зажимов или изоляционной ленты. Для защиты проводки заизолируйте провода в местах их соприкосновения с металлическими деталями. — Разместите все кабели в удалении от подвижных деталей, таких как рычаг переключения передач и направляющие сидений. — Разместите все кабели в удалении от нагревающихся деталей, таких как решетка обогревателя. 114 — Запрещается подключать желтый провод дисплея к аккумуляторной батарее автомобиля через сверленое отверстие в отсеке двигателя. — Изолируйте концы всех не подсоединенных кабелей изоляционной лентой. — Не укорачивайте кабели. — Никогда не срезайте изоляцию со шнура питания данного устройства с целью подачи питания на другое устройство. Допустимая нагрузка кабеля по току ограничена. — Используйте предохранитель с указанными параметрами. — Запрещается напрямую заземлять отрицательный вывод громкоговорителя. — Запрещается связывать вместе отрицательные кабели нескольких громкоговорителей. ! При включении питания устройства управляющий сигнал подается через синебелый провод. Подключите этот провод к клемме пульта управления внешнего усилителя мощности или клемме реле управления антенны с электроприводом (макс. 300 мА 12 В постоянного тока). Если автомобиль оборудован встроенной в оконное стекло антенной, подсоедините провод к клемме питания усилителя антенны. ! Запрещается подсоединять сине-белый кабель к клемме питания внешнего усилителя мощности. Также запрещается подсоединять данный провод к клемме питания антенны с электроприводом. В противном случае может возникнуть утечка тока аккумуляторной батареи или иная неисправность. ! Черный кабель является заземляющим. Заземляющие кабели данного устройства и других устройств (особенно устройств, предназначенных для эксплуатации при больших токах, таких как усилитель мощности) должны монтироваться отдельно. В противном случае их случайное отсоединение может привести к пожару или неисправности. Шнур питания 2 Данное устройство 7 3 4 5 6 3 4 5 6 1 8 a 9 1 23 4 5 Гнездо антенны Плавкий предохранитель (10 A) Гнездо шнура питания Вход проводного пульта дистанционного управления Служит для подключения проводного адаптера пульта дистанционного управления (приобретается отдельно). 5 Выход заднего канала или выход сабвуфера 1 2 3 4 e b c d 1 К гнезду шнура питания 2 В зависимости от типа автомобиля функции 3 и 5 могут отличаться. В этом случае следует подключить 4 к 5 и 6 к 3. 3 Желтый Резервный разъем (или разъем дополнительного оборудования) 4 Желтый Подключите к клемме источника постоянного тока 12 В. 5 Красный Разъем дополнительного оборудования (или резервный разъем) 6 Красный Подключите к клемме, на которую подается напряжение (12 В постоянного тока) при включении зажигания. 7 Подсоедините провода одинакового цвета друг к другу. 8 Черный (заземление на массу) Ru <QRD3247-B> 114 Black plate (115,1) Раздел Установка Примечания ! Требуется изменение стартового меню данного устройства. См. SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 113. Выход сабвуфера данного устройства монофонический. ! При использовании сабвуфера мощностью 70 Вт (2 W) обязательно подсоедините к сабвуферу фиолетовый и фиолетовый/черный провод данного устройства. Не подсоединяйте зеленый и зеленый/черный провода. Усилитель мощности (приобретается отдельно) Используйте данную схему подсоединения при использовании дополнительного усилителя мощности. ! Не используйте детали, не разрешенные производителем к использованию, поскольку это может стать причиной неисправностей. ! Уточните у дилера компании, требует ли установка сверления отверстий или внесения иных изменений в конструкцию автомобиля. ! Не устанавливайте данное устройство в местах, где оно может: — помешать управлению автомобилем. — травмировать пассажира при внезапной остановке автомобиля. Порядок установки Данное устройство можно устанавливать одним из описанных ниже способов. ! Установка с кронштейном ! Установка с помощью резьбовых отверстий на боковых панелях устройства Перед установкой данного устройства 1 Снимите рамку. ! Перегрев полупроводникового лазера приведет к его выходу из строя. Разместите все кабели в удалении от нагревающихся деталей, таких как решетка обогревателя. ! Оптимальной является установка устройства под углом менее 60°. 3 1 5 03 2     60° 4 5 1 Пульт дистанционного управления системой Подсоедините синий/белый кабель. 2 Усилитель мощности (приобретается отдельно) 3 Подключите с помощью кабелей RCA (приобретаются отдельно) 4 К выходу заднего канала или выходу сабвуфера 5 Задний громкоговоритель или сабвуфер Установка Важно ! Перед окончательной установкой проверьте все соединения и системы. 1 ! При установке необходимо обеспечить эффективный отвод тепла, оставив достаточное пространство за задней панелью и закрепив свободные кабели так, чтобы они не закрывали вентиляционные отверстия. Оставить просторное место 1 Декоративная рамка 2 Вставьте прилагаемые экстракторы с обеих сторон устройства до щелчка. 5 см 5 см 5cm cm 3 Извлеките устройство из кронштейна. Снимите кронштейн. Русский 9 Синий/белый Расположение штекера разъема ISO на различных автомобилях может отличаться. Если штекер 5 предназначен для управления антенной, подсоедините 9 к b. На других автомобилях подключать 9 к b запрещается. a Синий/белый Подключите к клемме панели управления усилителя мощности (макс. 300 мА 12 В постоянного тока). b Синий/белый Подключите к клемме реле управления антенны с электроприводом (макс. 300 мА 12 В постоянного тока). c Желтый/черный Если используется оборудование, имеющее функцию приглушения звука, данный провод необходимо подсоединить к клемме Audio Mute данного устройства. В противном случае необходимо проследить за тем, чтобы данный провод не контактировал с любыми другими разъемами. d Выводы громкоговорителей Белый: Передний левый + Белый/черный: Передний левый * Серый: Передний правый + Серый/черный: Передний правый * Зеленый: Задний левый + или сабвуфер + Зеленый/черный: Задний левый * или сабвуфер * Фиолетовый: Задний правый + или сабвуфер + Фиолетовый/черный: Задний правый * или сабвуфер * e Разъем ISO В некоторых автомобилях разъем ISO может иметь два вывода. В этом случае необходимо подсоединить оба разъема. Установка ! При установке используйте детали, имеющиеся в продаже. Ru <QRD3247-B> 115 115 Black plate (116,1) Раздел Установка 03 Установка 1 2 Установите устройство. % Крепление устройства на заводской установочный кронштейн. Расположите устройство таким образом, чтобы его резьбовые отверстия совпадали с резьбовыми отверстиями кронштейна, и затяните по три винта на каждой стороне. 1 1 Кронштейн (входит в комплект поставки) Установка с кронштейном 1 Установите кронштейн на приборную панель. После установки кронштейна на приборную панель выберите подходящие фиксаторы, исходя из толщины материала приборной панели, и подогните их. (С помощью верхних и нижних фиксаторов закрепите данное устройство как можно надежнее. Для надежной фиксации устройства необходимо подогнуть фиксаторы на 90 градусов.) Установка с помощью резьбовых отверстий на боковых панелях устройства 1 Приборная панель 3 Установите рамку. 1 2 1 1 1 Декоративная рамка Извлечение кронштейна 2 1 Приборная панель 2 Кронштейн (входит в комплект поставки) 116 Порядок действий тот же, что перед установкой устройства. Подробнее см. в разделе Перед установкой данного устройства на стр. 115. 3 4 1 Подогните зажим, если он мешает установке. 2 Заводской установочный кронштейн 3 Крепежные (5 мм × 8 мм) винты 4 Приборная панель или консоль Ru <QRD3247-B> 116 Black plate (117,1) Приложение Дополнительная информация Устранение неисправностей Симптомы выделены жирным шрифтом; причины показаны обычным шрифтом без отступа. Способы устранения показаны обычным шрифтом с отступом. Дисплей автоматически возвращается в исходный режим. В течение 30 секунд не было выполнено никаких операций. Повторите операцию. Диапазон повторного воспроизведения самопроизвольно изменяется. В зависимости от выбранного диапазона воспроизведения он может изменяться при выборе другой папки или дорожки, а также при перемотке вперед/назад. Выберите диапазон повторного воспроизведения еще раз. Устройство функционирует с ошибками. Имеются помехи. Вложенные папки не воспроизводятся, если выбран диапазон FLD (повторное воспроизведение папки). Выберите другой диапазон повторного воспроизведения. При изменении дисплея отображается NO XXXX (например, NO TITLE). Текстовая информация отсутствует. Переключите дисплей или включите воспроизведение другой дорожки/файла. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Используется устройство, например, сотовый телефон, которое может вызывать шумовые помехи. Уберите прибор, вызывающий помехи, от этого устройства. Электрическая или механическая неисправность. Установите ключ зажигания в положение OFF, а затем – в положение ON или переключитесь на другой источник сигнала, а затем обратно на проигрыватель компактдисков. Сообщения об ошибках ERROR-15 Прежде чем обратиться к торговому представителю или в ближайший сервисный центр Pioneer, обязательно запомните сообщение об ошибке. Сообщения об ошибках выделены жирным шрифтом; причины показаны обычным шрифтом без отступа. Способы устранения показаны обычным шрифтом с отступом. Общие AMP ERROR Вложенная папка не воспроизводится. Дополнительная информация Устройство не работает или неправильно подсоединен громкоговоритель; сработала цепь защиты. Проверьте, подключен ли громкоговоритель. Если сообщение не исчезает даже после выключения/выключения зажигания, свяжитесь с дилерским центром или авторизованным сервисным центром Pioneer. Проигрыватель компакт-дисков Вставлен пустой диск. Замените диск. ERROR-23 Формат диска не поддерживается. Замените диск. FORMAT READ Иногда происходит задержка между началом воспроизведения и появлением звука. Звук появится после того как с дисплея исчезнет сообщение. NO AUDIO На диске отсутствуют файлы, которые можно воспроизвести. Замените диск. SKIPPED Диск содержит файлы, защищенные технологией DRM. Защищенные файлы пропускаются. PROTECT Диск загрязнен. Очистите диск. Все файлы на диске защищены технологией DRM. Замените диск. Диск поцарапан. Замените диск. Иногда происходит задержка между началом воспроизведения и появлением звука. Звук появится после того как с дисплея исчезнет сообщение. NO AUDIO Композиции отсутствуют. Перенесите аудиофайлы на запоминающее устройство USB и подключите его. На подключенном запоминающем устройстве USB включена функция защиты от перезаписи. Отключите функцию защиты от перезаписи в соответствии с инструкцией по эксплуатации запоминающего устройства USB. SKIPPED На подключенном запоминающем устройстве USB содержатся файлы, защищенные технологией DRM. Защищенные файлы пропускаются. PROTECT Все файлы на подключенном запоминающем устройстве USB защищены технологией DRM. Замените запоминающее устройство USB. N/A USB Подключенное устройство USB не поддерживается данным устройством. ! Подключите запоминающее устройство USB класса Mass Storage. ! Отсоедините устройство и замените его на совместимое запоминающее устройство USB. Ru <QRD3247-B> 117 Русский ERROR-07, 11, 12, 17, 30 Запоминающее устройство USB/iPod FORMAT READ 117 Black plate (118,1) Приложение Дополнительная информация CHECK USB ERROR-23 Короткое замыкание на разъеме USB или в кабеле USB. Убедитесь, что разъем USB или кабель USB не защемлен и не поврежден. Запоминающее устройство USB не отформатировано в системе FAT12, FAT16 или FAT32. Запоминающее устройство USB должно быть форматировано в FAT12, FAT16 или FAT32. CHECK USB ERROR-16 Подключенное запоминающее устройство USB потребляет больше максимально допустимой силы тока. Отсоедините запоминающее устройство USB и не используйте его. Установите ключ зажигания в положение OFF, затем – в положение ACC или ON, и затем подключайте только совместимые запоминающие устройства USB. Устаревшая версия прошивки iPod. Обновите версию прошивки iPod. CHECK USB iPod работает, но не подзаряжается. Убедитесь в отсутствии короткого замыкания в кабеле iPod (например, что кабель не зажат между металлическими предметами). После проверки кабеля установите ключ зажигания в положение OFF, а затем – в положение ON, либо отключите и заново подключите iPod. ERROR-19 Сбой связи. Выполните следующие действия. – Установите ключ зажигания в положение OFF, а затем – в положение ON. – Отключите запоминающее устройство USB. – Выберите другой источник сигнала. Затем вновь выберите USB в качестве источника сигнала. Сбой iPod. Отключите кабель от iPod. После появления на дисплее главного меню iPod заново подключите iPod и перезагрузите его. Дополнительная информация Рекомендации по обращению с изделием Диски и проигрыватель Используйте только диски, имеющие один из следующих логотипов. Сбой iPod. Отключите кабель от iPod. После появления на дисплее главного меню iPod заново подключите iPod и перезагрузите его. STOP В текущем списке отсутствуют композиции. Выберите список, содержащий музыкальные композиции. NOT FOUND Композиций не найдено. Загрузите композиции на iPod. Приложение еще не запущено. Следуйте экранным подсказкам. Воспроизведение дисков может быть невозможно из-за характеристик диска, формата диска, приложения, при помощи которого выполнялась запись, условий воспроизведения, условий хранения и других факторов. Толчки от неровностей дороги могут вызвать прерывание воспроизведения диска. Используйте 12-см диски. Используйте только обычные круглые диски. Следующие типы дисков нельзя использовать на данном устройстве: ! Диски формата DualDisc ! 8-см диски: попытки использовать такие диски с помощью адаптера могут привести к неисправности устройства. ! Диски необычных форм Приложение START UP APP Конденсация может временно ухудшить работу проигрывателя. Оставьте его для адаптации к более высокой температуре примерно на час. Также удалите влагу с дисков с помощью мягкой ткани. ! Диски других форматов, кроме CD ! Поврежденные диски, в т.ч. с трещинами, с отколотыми краями или деформированные ! Диски CD-R/RW, запись на которых не была завершена При использовании дисков, на поверхность которых могут наноситься этикетки, изучите инструкции и предупреждения для этих дисков. Установка и извлечение некоторых дисков могут быть невозможны. Использование таких дисков может привести к повреждению оборудования. Не приклеивайте на диски этикетки и другие материалы. ! Это может деформировать диски, в результате чего их воспроизведение будет невозможным. ! Этикетки могут отклеиться во время воспроизведения и затруднить извлечение дисков, а также повредить оборудование. Запоминающее устройство USB Не прикасайтесь к записанной поверхности дисков. Подключение через USB-концентратор не поддерживается. Когда диски не используются, храните их в футлярах. Не подключайте другие устройства, кроме запоминающих устройств USB. Не приклеивайте этикеток, не пишите и не наносите химических веществ на поверхность дисков. Для очистки компакт-диска протрите диск мягкой тканью от центра к краю. 118 Ru <QRD3247-B> 118 Black plate (119,1) Приложение Дополнительная информация При движении автомобиля надежно закрепите запоминающее устройство USB. Не роняйте запоминающее устройство USB на пол, где оно может застрять под педалью тормоза или акселератора. В зависимости от типа запоминающего устройства USB могут возникнуть следующие проблемы. ! Управление функциями может отличаться. ! Запоминающее устройство может не распознаваться. ! Файлы не могут воспроизводиться корректно. ! Устройство может создавать шумовые помехи во время прослушивания радио. iPod Не оставляйте iPod в местах с высокой температурой воздуха. При движении автомобиля надежно закрепите iPod. Не роняйте iPod на пол, где он может застрять под педалью тормоза или акселератора. WMA Расширение: .wma Скорость передачи данных: от 48 кбит/с до 320 кбит/с (постоянная), от 48 кбит/с до 384 кбит/с (переменная) Частота дискретизации: 32 кГц, 44,1 кГц, 48 кГц Windows MediaäAudio Professional, Lossless, Voice/DRM Stream/Stream с поддержкой видео: не поддерживается MP3 WAV Расширение: .wav Разрядность квантования: 8 и 16 (LPCM), 4 (MS ADPCM) Частота дискретизации: от 16 кГц до 48 кГц (LPCM), 22,05 кГц и 44,1 кГц (MS ADPCM) ! Эта функция не работает, если выбрано USB MTP. Дополнительная информация В качестве названия файла или папки могут отображаться только первые 32 символа (включая расширение). Частота дискретизации: от 8 кГц до 48 кГц (32 кГц, 44,1 кГц, 48 кГц пиковая) Для отображения в данном устройстве кодировка русского текста должна соответствовать одному из следующих наборов символов: ! Юникод (UTF-8, UTF-16) ! Отличный от Юникода набор символов, использующийся в среде Windows, для которого в языковой настройке задан русский язык Совместимая версия тегов ID3: 1.0, 1.1, 2.2, 2.3, 2.4 (теги ID3 версии 2.x имеют приоритет перед версией 1.x.) Это устройство может работать некорректно в зависимости от приложений, использованных для кодирования файлов WMA. Списки воспроизведения M3u: не поддерживаются При начале воспроизведения аудиофайлов, содержащих изображения, и файлов с запоминающего устройства USB, содержащего разветвленные иерархии папок, может происходить небольшая задержка. Расширение: .mp3 Скорость передачи данных: от 8 кбит/с до 320 кбит/с (постоянная), переменная MP3i (интерактивный MP3), mp3 PRO: не поддерживаются Диск Допустимая иерархия папок: до восьми уровней (реальная иерархия папок составляет менее двух уровней) Количество воспроизводимых папок: не более 99 Количество воспроизводимых файлов: не более 999 Файловая система: ISO 9660 уровень 1 и 2, Romeo, Joliet Воспроизведение нескольких сессий: поддерживается Пакетный формат записи: не поддерживается Независимо от продолжительности паузы между композициями в изначальной записи, при воспроизведении дисков со сжатыми аудиофайлами между композициями будут короткие паузы. Запоминающее устройство USB Допустимая иерархия папок: до восьми уровней (реальная иерархия папок составляет менее двух уровней) Количество воспроизводимых папок: не более 500 Количество воспроизводимых файлов: не более 15 000 Воспроизведение защищенных от копирования файлов: не поддерживается Русский Настройки iPod ! При подключении iPod к данному устройству эквалайзер iPod автоматически отключается, что обеспечивает оптимальное звучание. При отсоединении iPod для эквалайзера автоматически выбирается предыдущая настройка. ! При использовании данного устройства отключение функции повторного воспроизведения на iPod невозможно. Если iPod подключен к данному устройству, будет автоматически выбран режим повтора всех композиций. Поддержка сжатых аудиофайлов (компактдиск, USB) Дополнительная информация Текстовая информация несовместимого формата, сохраненная на iPod, не будет отображаться на дисплее данного устройства. Ru <QRD3247-B> 119 119 Black plate (120,1) Приложение Дополнительная информация Запоминающее устройство USB, содержащее разделы: воспроизводится только первый раздел. При начале воспроизведения аудиофайлов на запоминающем устройстве USB, содержащем разветвленные иерархии папок, может возникать небольшая задержка. ВНИМАНИЕ ! Pioneer не гарантирует совместимость со всеми устройствами USB mass storage и не несет ответственности за любую потерю данных на медиапроигрывателях, смартфонах и других устройствах при использовании этого изделия. ! Не оставляйте диски или запоминающее устройство USB в местах с высокой температурой воздуха. Дополнительная информация ! iPhone 3GS ! iPhone 3G ! iPhone Пользователям iPod с интерфейсом Dock Connector потребуется кабель CD-IU51. Подробную информацию можно получить по месту покупки. О совместимости файлов/форматов см. в руководствах к iPod. Поддержка iPod 120 02 1 2 03 ВНИМАНИЕ Компания Pioneer не несет ответственности за потерю данных на iPod, даже если эти данные будут потеряны во время использования данного устройства. Последовательность воспроизведения аудиофайлов Пользователь не может назначать номера папок и устанавливать последовательность воспроизведения с помощью данного устройства. 3 4 04 5 6 Функции iPod могут различаться в зависимости от версии программного обеспечения. Аудиокниги, подкасты: поддерживаются Данное устройство поддерживает только нижеперечисленные модели iPod. Сделано для ! iPod touch (5-го поколения) ! iPod touch (4-го поколения) ! iPod touch (3-го поколения) ! iPod touch (2-го поколения) ! iPod touch (1-го поколения) ! iPod classic ! iPod с поддержкой видео ! iPod nano (7-го поколения) ! iPod nano (6-го поколения) ! iPod nano (5-го поколения) ! iPod nano (4-го поколения) ! iPod nano (3-го поколения) ! iPod nano (2-го поколения) ! iPod nano (1-го поколения) ! iPhone 5 ! iPhone 4S ! iPhone 4 01 В зависимости от версии программного обеспечения или поколения iPod некоторые функции могут быть недоступны. Пользователям iPod с интерфейсом Lightning потребуется кабель Lightning - USB (входит в комплект поставки iPod). Таблица символов для русского языка Пример иерархии 05 : Папка : Сжатый аудиофайл от 01 до 05: Номер папки от 1 до 6: Последовательность воспроизведения Диск Последовательность выбора папок и других действий может отличаться в зависимости от кодировки или программного обеспечения, использованного для записи. Запоминающее устройство USB Файлы воспроизводятся в той последовательности, в которой они записаны на запоминающем устройстве USB. Для выбора алгоритма воспроизведения рекомендуется выполнить следующие действия. 1 Присвойте файлам имена с цифрами, определяющими последовательность воспроизведения (например, 001xxx.mp3 и 099yyy.mp3). 2 Поместите эти файлы в папку. 3 Сохраните папку, содержащую файлы, на запоминающем устройстве USB. Учитывайте, что в некоторых системных средах невозможно установить порядок воспроизведения. Последовательность воспроизведения файлов на портативном аудиоплеере USB может изменяться и зависит от типа плеера. Д: Б Д: Б Д: Б Д: Б Д: Б :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю Д: Дисплей Б: Буква Авторское право и товарные знаки MP3 Поставка этого изделия дает право только на его частное и некоммерческое использование и не предоставляет лицензии и не подразумевает право использования этого изделия в любых коммерческих (т.е. приносящих прибыль) прямых трансляциях (телевизионных, спутниковых, кабельных и/или любых других), вещании/потоковой передаче через Интернет, локальных сетях и/или других сетях или в других электронных системах распространения, таких как системы платного аудио и аудио по запросу. Для такого использования необходима специальная лицензия. Дополнительную информацию см. на сайте http://www.mp3licensing.com. WMA Windows Media – это зарегистрированная торговая марка или торговая марка Microsoft Corporation в США и/или других странах. Ru <QRD3247-B> 120 Black plate (121,1) Приложение Дополнительная информация В данном изделии используются технологии, принадлежащие корпорации Microsoft, которые не разрешается использовать или распространять без лицензии от Microsoft Licensing, Inc. iPod и iPhone iPhone, iPod, iPod classic, iPod nano и iPod touch являются товарными знаками компании Apple Inc., зарегистрированными в США и других странах. Lightning является торговым знаком компании Apple Inc. “Made for iPod” и “Made for iPhone” означает, что электронный прибор был разработан с целью подключения определенно к iPod или iPhone соответственно, и имеется сертифицикация разработчика о соответствии с техническими характеристиками Apple. Apple не несет ответственности за работу данного устройства или его соответствие со стандартами по технике безопасности или регулятивными нормами. Пожалуйста, обратите внимание, что использование данного прибора с iPod или iPhone может отрицательно сказываться на качестве беспроводной связи. Дополнительная информация Серийный номер На этом рисунке показана информация о месяце и годе изготовления устройства. 12 цифр 10 цифр 2 цифры P1 P2 Дата изготовления оборудования P1 - Год изготовления 2001 2002 Год Символ A B Год Символ 2011 K 2012 L P2 - Месяц изготовления Месяц 1 2 3 Символ A B C 2003 C 2004 D 2005 E 2006 F 2007 G 2008 H 2009 I 2010 J 2013 M 2014 N 2015 O 2016 P 2017 Q 2018 R 2019 S 2020 T 4 D 5 E 6 F 7 G 8 H 9 I 10 J 11 K 12 L Androidä Android является товарным знаком компании Google Inc. Русский Ru <QRD3247-B> 121 121 Black plate (122,1) Приложение Дополнительная информация Технические характеристики Общие Источник питания ........... 14,4 В постоянного тока (допустимый диапазон от 10,8 В до 15,1 В) Система заземления ..... Заземление отрицательного полюса Максимальный потребляемый ток ................................... 10,0 А Размеры (Ш × В × Г): DIN Шасси ............................. 178 мм × 100 мм × 157 мм Передняя панель ........... 188 мм × 118 мм × 25 мм D Шасси ............................. 178 мм × 100 мм × 165 мм Передняя панель ........... 170 мм × 96 мм × 17 мм Масса ............................. 1,2 кг Аудио Максимальная выходная мощность ................................... 50 Вт × 4 70 Вт × 1/2 W (для сабвуфера) Номинальная выходная мощность ................................... 22 Вт × 4 (от 50 Гц до 15 000 Гц, суммарное значение коэффициента нелинейных искажений 5 %, нагрузка 4 W для обоих каналов) Сопротивление нагрузки ................................... 4 W (допустимо – от 4 W до 8 W) Максимальная выходная мощность ................................... 2,0 В Контур громкости ........... +10 дБ (100 Гц), +6,5 дБ (10 кГц) (громкость: –30 дБ) Эквалайзер (5-полосный графический эквалайзер): Частота ........................... 80 Гц/250 Гц/800 Гц/2,5 кГц/ 8 кГц Диапазон амплитудно-частотных характеристик ................................... ±12 дБ (с шагом 2 дБ) 122 Дополнительная информация Сабвуфер (моно): Частота ........................... 50 Гц/63 Гц/80 Гц/100 Гц/ 125 Гц/160 Гц/200 Гц Крутизна характеристики ................................... –12 дБ/окт, –24 дБ/окт Усиление ........................ +6 дБ до –24 дБ Фаза ............................... Нормальная/Обратная Диапазон частот ............. от 531 кГц до 1 602 кГц Полезная чувствительность ................................... 25 мкВ (отношение сигнал/ шум: 20 дБ) Отношение сигнал/шум ................................... 62 дБ (сеть IEC-A) Проигрыватель компакт-дисков LW-тюнер Система ......................... Аудиосистема с компакт-диском Используемые диски ..... Компакт-диск Отношение сигнал/шум ................................... 94 дБ (1 кГц) (сеть IEC-A) Число каналов ............... 2 (стерео) Формат декодирования файлов MP3 ................................... MPEG-1 и 2 Audio Layer 3 Формат декодирования файлов WMA ................................... Версии 7, 7.1, 8, 9, 10, 11, 12 (двухканальный звук) (Windows Media Player) Формат сигнала WAV ..... Linear PCM и MS ADPCM (без компрессии) USB Стандартная спецификация USB ................................... USB 2.0 полноскоростной Максимальный ток питания ................................... 1 А Класс USB ...................... MSC (Mass Storage Class) Файловая система ......... FAT12, FAT16, FAT32 Формат декодирования файлов MP3 ................................... MPEG-1 и 2 Audio Layer 3 Формат декодирования файлов WMA ................................... Версии 7, 7.1, 8, 9, 10, 11, 12 (двухканальный звук) (Windows Media Player) Формат сигнала WAV ..... Linear PCM и MS ADPCM (без компрессии) MW-тюнер Диапазон частот ............. от 153 кГц до 281 кГц Полезная чувствительность ................................... 28 мкВ (отношение сигнал/ шум: 20 дБ) Отношение сигнал/шум ................................... 62 дБ (сеть IEC-A) Примечание: В соответствии со статьей 5 закона Российской Федерации «О защите прав потребителей» и постановлением правительства Российской Федерации № 720 от 16.06.97 компания Pioneer Europe NV оговаривает следующий срок службы изделий, официально поставляемых на российский рынок. Автомобильная электроника: 6 лет Прочие изделия (наушники, микрофоны и т.п.): 5 лет Примечания ! Характеристики и конструкция могут быть изменены без предварительного уведомления. ! Данное устройство произведено в Таиланде. FM-тюнер Диапазон частот ............. от 87,5 МГц до 108,0 МГц Полезная чувствительность ................................... 9 дБф (0,8 мкВ/75 W, моно, отношение сигнал/шум: 30 дБ) Отношение сигнал/шум ................................... 72 дБ (сеть IEC-A) Ru <QRD3247-B> 122 Black plate (123,1) Русский Ru <QRD3247-B> 123 123 <QRD3247-B> 124 <QRD3247-B> 125 <QRD3247-B> 126 <QRD3247-B> 127 Black plate (124,1) PIONEER CORPORATION 28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, JAPAN Корпорация Пайонир 28-8, Хонкомагомэ 2-чоме, Бункё-ку, Токио 113-0021, Япония Импортер ООО “ПИОНЕР РУС” 105064, Россия, г. Москва, Нижний Сусальный переулок, дом 5, строение 19 Тел.: +7(495) 956-89-01 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique TEL: (0) 3/570.05.11 PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901 TEL: 905-479-4411 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 2 Jalan Kilang Barat, #07-01, Singapore 159346 TEL: 65-6378-7888 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202 Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MÉXICO S.A. de C.V. Blvd.Manuel Ávila Camacho 138, 10 piso Col.Lomas de Chapultepec, México, D.F. 11000 TEL: 52-55-9178-4270 FAX: 52-55-5202-3714 先鋒股份有限公司 台北市內湖區瑞光路407號8樓 電話: 886-(0)2-2657-3588 先鋒電子(香港)有限公司 香港九龍長沙灣道909號5樓 電話: 852-2848-6488 ã 2013-2016 PIONEER CORPORATION. All rights reserved. ã 2013-2016 PIONEER CORPORATION. Tous droits de reproduction et de traduction réservés. ã PIONEER CORPORATION, 2013-2016. Все права защищены. <KOKZ16E> <QRD3247-B> EW <QRD3247-B> 128
1 / 1

Pioneer FH-460UI Manual de usuario

Categoría
Receptores de medios de coche
Tipo
Manual de usuario